email: [email protected] Customer Service: 800.445.3988 www.autorefinishdevilbiss.com ©2012 DeVilbiss Automotive Refinishing All rights reserved Form No. A-2987 Litho in U.S.A. 5/12 A-2987
email: [email protected] Service: 800.445.3988www.autorefinishdevilbiss.com
©2012 DeVilbiss Automotive Refinishing All rights reserved Form No. A-2987 Litho in U.S.A. 5/12
A-2987
Waterborne Finishing . . . . . . . . . . . 3-4
Guns & Accessories
Gravity Guns & Accessories . . . . . . 5–21
Suction Guns & Accessories . . . . . 22–26
Pressure Guns . . . . . . . . . . . . 27–31
Pressure Tanks & Accessories . . . . 32–34
Disposable Cups & Accessories
. . . . . . . . . . . . . . . . . . . . . 35–44
Airbrushes & Accessories
. . . . . . . . . . . . . . . . . . . . . 45–48
Air Control
Air Filtration . . . . . . . . . . . . . . 49–55
Hose and Fittings . . . . . . . . . . . 56–60
Air Regulators & Adjusting Valves . . 61–62
Breathable Air . . . . . . . . . . . . . 63–65
Clean Solutions
. . . . . . . . . . . . . . . . . . . . . 66–69
Maintenance & Accessories
. . . . . . . . . . . . . . . . . . . . . 70–77
Properly Piped Shop Diagram
. . . . . . . . . . . . . . . . . . . . . 78–79
Waterborne-Compatible Spray Guns
Waterborne Finishing•Spray Guns–Separate guns for waterborne base coats and solvent top
coats should be used to avoid cross contamination and material coagulation. Waterborne guns should have corrosion-resistant fluid passages, gun body and paint cup. DeVilbiss offers the TEKNA® QuickClean™, TEKNA® Copper, TEKNA® ProLite, CVi®, FinishLine® FLG-4, PRi®, and SRiPro™ in both high efficiency and HVLP, all proven with waterborne materials.
•Disposable Cup Systems–Waterborne materials can corrode metal cups and are difficult to remove from plastic cups if not cleaned promptly after using. Disposable cup systems make paint clean up easy and cost effective. DeVilbiss disposable cup systems are an ideal solution for increased productivity and shop savings.
•Drying Systems–Air movement significantly reduces the drying time of waterborne materials, resulting in higher productivity and lower costs. The most economical and flexible choices are portable, hand-held dryers like the CAMAIR® Aerodry® Paint Dryer from DeVilbiss. The CAMAIR® Aerodry® Paint Dryer is very effective in creating air movement while using less air volume than competitors. A portable and adjustable two blower stand is recommended.
•Paint Filtration–Look for strainers that have the adhesive applied on the outside of the strainer to avoid adhesive residue contamination. Be sure to follow manufacturer recommendations for straining paint materials.
•Gun Cleaners for Waterborne–A separate gun cleaner is needed for waterborne materials. These are made of non-corrosive materials and use water and waterborne cleaning solutions to clean spray equipment.
TEKNA® All models
CVi® CVI-620G, CVI-620GW, CVI-501-510-10
PRi® PRI-612G
FinishLine® FLG-4 FLG-670, FLG-671, FLG-678
SRiPro™ SRIPRO-635G-10
Look for this symbol throughout the catalog to find tools compatible with waterborne materials. Spray guns with this designation are compatible when using a plastic or disposable cup system.
WaterborneCompatible
Waterborne Finishing 32
Order No.130530 Dryer Gun
CamAir® Paint DryerOrder No. Description
130529 Two-Gun Stand130530 Dryer Gun
•Waterbornepaintdryerreducesdrying time
•Coandaeffectamplifiesinletairflow about 7 times
•Ultraquiet
Aerodry®
Paint DryerOrder No.130529 Two-Gun Stand with 2 Dryer Guns
Efficient Amplified Drying
SPECiFiCATiONSMaximuminletpressure: 100 PSIGTypicalairflows fordryergun: inlet inlet Outlet PSi CFM CFM
20 5.5 43 30 7.5 52 40 9.5 61 50 11.5 72
ROOMAiR iNlET
FlOW OuTlET52 CFM*
* TyPiCAl APPliCATiON SHOWN
SHOP AiR iNlET30 PSi
uSiNG 7.5 CFM*
&Accessories
Gravity Guns
5Waterborne Finishing4
GrAvity SPrAy Gun
includes:•Multipleaircapsandnozzles•HAV-555digitalairadjustingvalvewithgauge•GunwrenchandcolorIDrings•Lightweightergonomicdesign
TEKNA® ProLite Air CapsTE10 air cap Basecoats, low solids clear coats(HE) AirCapOrder/ModelNo.703538 7.5–11 CFM @ 20–35 PSI inlet
TE20 air cap Basecoats, high solids clear coats(HE) AirCapOrder/ModelNo.703539 9–12 CFM @ 16–26 PSI inlet
HV30 air cap Basecoats, clear coats(HVlP) AirCapOrder/ModelNo.703540 14.5–16.5 CFM @ 20–24 PSI inlet
Fluid Tips 1.2mm, 1.3mm, 1.4mm, 1.5mm
Air Cap Pattern
12–13"
Air Cap Pattern
13–14"
Air Cap Pattern
12–13"
HAV-555
3 Models Available! 703566
*Waterbornecompatiblewhenusingaplasticordisposablecupsystem.Viewourapprovallettersatwww.autorefinishdevilbiss.com
703517, 703567
•Incrediblyfastcleanup•Coatinghasnon-stickproperties•Excellentforsolventandwaterbornecoatings•Gunbodycoatedinsideandout
tEKnA® QuickClean™
GrAvity SPrAy Gun
includes:•HAV-555digitalairadjusting
valve with gauge•Extraneedle/nozzleset•GunwrenchandcolorIDrings
TEKNA® QuickClean™ Air Caps#7E7 air cap Base coats, clearcoats(HE) AirCapOrder/ModelNo.703062 9-11 CFM @ 16-22 PSI inlet forHVLPapprovedareas
#202 air cap Base coats (solvent)(HVlP) AirCapOrder/ModelNo.702723 13.5-15.5 CFM @ 18-22 PSI inlet
#909 air cap Clearcoats, waterborne base coats(HVlP) AirCapOrder/ModelNo.702724 14-16 CFM @ 22-26 PSI inlet
Fluid Tips 1.1mm, 1.2mm, 1.3mm, 1.4mm, 1.5mm (forhotclimatewaterborne)
Air Cap Pattern
12½"
Air Cap Pattern
12"
Air Cap Pattern
13"
HAV-555
4 Models Available!
703507, 703509
703506, 703508
*Waterbornecompatiblewhenusingaplasticordisposablecupsystem.
TEKNA® QuickClean™ Basecoat/Clearcoat Gravity Feed Spray GunsOrder no. needle/nozzle Cup Air Cap
703506 1.2mm, 1.3mm Uncupped IncludesDPCadapter
7E7
703507 1.2mm, 1.3mm 900ccAluminum 7E7
703508 1.3mm, 1.4mm Uncupped IncludesDPCadapter
7E7 & 909
703509 1.3mm, 1.4mm 900ccAluminum 7E7
WaterborneCompatible
WaterborneCompatible
EPA Compliant. Approved in most
HVlP areas.
EPA Compliant. Approved in most
HVlP areas.
Gravity Guns Gravity Guns 76
TEKNA® ProLite Gravity Feed Spray GunsOrder no. needle/nozzle Cup Air Cap
703517 1.3 & 1.4 Uncupped IncludesDPCadapter
TE20 & HV30
703567 1.2, 1.3, & 1.4 Uncupped IncludesDPCadapter
TE10 & TE20
703566 1.2, 1.3, & 1.4 900ccAluminum TE10 & TE20
tEKnA® Copper HEGrAvity SPrAy Gun
includes:•HAV-555digitalairadjusting
valve with gauge•Extraneedle/nozzleset•GunwrenchandcolorIDrings
TEKNA® Copper Air Caps#7E7 air cap Base coats, clearcoats(HE) AirCapOrder/ModelNo.703062 9-11 CFM @ 16-22 PSI inlet forHVLPapprovedareas
#202 air cap Base coats (solvent)(HVlP) AirCapOrder/ModelNo.702723 13.5-15.5 CFM @ 18-22 PSI inlet
#909 air cap Clearcoats, waterborne base coats(HVlP) AirCapOrder/ModelNo.702724 14-16 CFM @ 22-26 PSI inlet
Fluid Tips 1.1mm, 1.2mm, 1.3mm, 1.4mm, 1.5mm (forhotclimatewaterborne)
Air Cap Pattern
12½"
Air Cap Pattern
12"
Air Cap Pattern
13"
HAV-555
4 Models Available!Cupped or uncupped
TEKNA® Copper Basecoat/Clearcoat Gravity Feed Spray GunsOrder no. needle/nozzle Cup Air Cap
703488 1.2mm, 1.3mm Uncupped IncludesDPCadapter
7E7
703489 1.2mm, 1.3mm 900ccAluminum 7E7
703496 1.3mm, 1.4mm Uncupped IncludesDPCadapter
7E7
703497 1.3mm, 1.4mm 900ccAluminum 7E7
703489, 703497
703488, 703496
*Waterbornecompatiblewhenusingaplasticordisposablecupsystem.
Gravity Gun/Cup(#510 trAnS-tECH HE AnD #505 HvLP Air CAPS inCLuDED in EACH mODEL)Order No. Model No.802851 CVi-620Gincludes:1.3mm&1.4mmfluidnozzles; 900ccaluminumgravitycupwithpush-onlid
Order No. Model No.802949 CVi-620GWIncludes:1.3mm&1.4mmfluidnozzles; 20oz.Acetalgravitycup
CVi® Gravity Feed Air Caps#505 air cap Base coats, clearcoats, primers, (HVlP) single stage, and low VOC AirCapOrderNo. 802841 AirCapModelNo. SP-100-505-K 14-18 PSI inlet 10-13 CFM
#510 air cap Primers, base coats, clearcoats, (HE) single stage, and low VOC AirCapOrderNo. 802546 AirCapModelNo. SP-100-510-K 20-26 PSI inlet 7.5-9 CFM
Fluid tips 1.0 mm, 1.2 mm, 1.3 mm, 1.4 mm
Air Cap Pattern
11¼"
Air Cap Pattern
11½"
CVi® Gravity Guns also include:•#510Trans-TechHEand#505HVLPaircaps•Spraygunlube•Fluidfilter•Gunhook•Airvalveassemblytool•HAV-512airadjustingvalvewithgauge
*Waterbornecompatiblewhenusingaplasticordisposablecupsystem.Visitautorefinishdevilbiss.comtoviewourapprovalletters.
WaterborneCompatible
WaterborneCompatible
EPA Compliant. Approved in most
HVlP areas.
EPA Compliant. Approved in most
HVlP areas.
Gravity Guns Gravity Guns 98
*Waterbornecompatiblewhenusingaplasticordisposablecupsystem.
Experiencethe Power of PluS...Powerful atomization• Twicetheenergyavailable inHVLPguns
Powerful productivity• Superfastfluidflowforhighspeedpainting
Powerful efficiency • EqualtoorbetterthanHVLPtransferefficiency
The choice for clearcoats
PLUS® Gravity Feed Order No. Fluid inlet Air Model No. Tip (mm) Pressure Applications
110264 1.2&1.3 25-35PSI BasecoatsGFG-670 30-40PSI Highsolidsclearcoats 30-40 PSI Single stages 1.4 30-40PSI Lowsolidsclearcoats 30-40 PSI Single stages
PLuS®
HiGH EFFiCiEnCy GrAvity FEED Gun/CuPOrder No.110264Model No.GFG-670
PluS® Gravity Gun includes:•1.2mm,1.3mm,and 1.4mmfluidtips
•900ccaluminumcupwithpushonlid
•HAV-511highoutput airadjustingvalve with gauge
•Spraygunlube,fluidfilter,gunhook
PLUS® Gravity Feed High Efficiency Air Cap#410 air cap Primers, base coats, clearcoats, single (HE) stage and low VOC AirCapOrderNo. 192174 AirCapModelNo. AV-440-410 30-40 PSI 9-11 CFM
Fluid tips 1.0 mm, 1.2 mm,1.3 mm, 1.4 mm, 1.6 mm, 1.8 mm (included tip sizes shown in bold)
Visitautorefinishdevilbiss.comtoviewourapprovalletters.
Air Cap Pattern
12½"
WaterborneCompatible
SriPro™ SPOt rEPAir GunOrder No.803311Model No.SRiPRO-635G-10
SmallGun•BIGPerformanceimproved comfort and balance• Newbodystyle;2-fingertrigger
ExcellentatomizationofsolventandwaterbornematerialsVersatile!• ¼"to9"fanpatternforeverythingfromspotrepairstodoorjambs,bumpers,smallpanels,andmotorcycletanks
Balanced air valve for smooth triggering and control during fading and blending
includes:•1.0mmfluidtip•TS1highefficiency&HS1HVLPaircaps•Startersetof9-oz.disposablecups: 4lidsandliners;1reusablesleeveand lidwith2plugs;1gunadapter; 1measuringguide;1300-micronbarrelpaintfilter;1125-microndiskfilter
•(3)3oz.plasticcupswithlids•Wrench,spraygunlube•4coloredidentificationrings
SRiPro™ Spot Repair Gun Air CapsHS1 air cap Primers, base coats, clearcoats, (HVlP) single stage, and low VOC AirCapOrderNo. 803296 AirCapModelNo. SRiPRO-101-HS1 29 PSI inlet 4.8 CFM
TS1 air cap Base coats, clearcoats, primers, (HE) single stage, and low VOC AirCapOrderNo. 803297 AirCapModelNo. SRiPRO-100-TS1 29 PSI inlet 3.5 CFM
Fluid tips 0.8 mm, 1.0 mm, 1.2 mm (included tip size shown in bold)
Air Cap Pattern
¼ to 9"
Air Cap Pattern
¼ to 9"
EPA Compliant.
Approved in most
HVlP areas.
NEW! Anodized
Finish
Gravity Guns Gravity Guns 1110
The Start of a Great Finish•Reducessanding andoverspray
•Spraysawidevarietyofprimersandotherundercoats
PRi® HVLP Gravity Feed PrimerOrder No. Fluid inlet Air Model No. Tip (mm) Pressure Applications
803248 1.4,1.8 15-20PSI Primersurfacers PRi-612G
Pri®
HvLP GrAvity FEED Gun/CuPOrder No.803248Model No.PRi-612G
PRi® Gravity Primer Gun includes:•900ccaluminumcupwithpushonlid
•SprayGunLube
PRi® Gravity Feed HVLP Primer Air Cap#101 air cap (HVlP) Primers including low VOC AirCapOrderNo. 192187 AirCapModelNo. PRi-407-101 16 CFM @ 30 PSI inlet
Fluid tips 1.2 mm, 1.3 mm, 1.4 mm, 1.5 mm, 1.6 mm, 1.8 mm, 2.0 mm, 2.2 mm (included tip sizes shown in bold)
Air Cap Pattern
11"
*Waterbornecompatiblewhenusingaplasticordisposablecupsystem.
GTi® Millennium Gravity Feed Order No. Fluid inlet Air Model No. Tip (mm) Pressure Applications
170156 1.3&1.4 20-25PSI Basecoats GTi-620G 25-30PSI Highsolidsclearcoats,singlestages 1.5 20-25PSI Basecoats 25-30PSI Lowsolidsclearcoats,singlestages(includes 1.3 mm, 1.4 mm, & 1.5 mm fluid tips)
Gti® millenniumHvLP GrAvity FEED Gun/CuPOrder No.170156Model No.GTi-620G
unique Air Cap Design Produces Painter- Friendly Pattern•Excellentvalue•Threegunsinone—includesthreedifferentfluidtips
GTi® Gravity Gun includes:•1.3mm,1.4mm,and 1.5mmfluidtips
•900ccaluminumcupwithpushonlid
•HAV-511highoutput airadjustingvalve with gauge
•Spraygunlube,fluidfilter,gunhook
GTi® Millennium Gravity Feed HVLP Air Cap#2000 air cap Base coats, clearcoats, primers, single (HVlP) stage, and low VOC AirCapOrderNo. 192136 AirCapModelNo. GTi-407-2000 20-30 PSI 12.5-16 CFM
Fluid tips 1.2 mm, 1.3 mm, 1.4 mm, 1.5 mm, 1.6 mm, 1.8 mm, 2.0 mm, 2.2 mm (included tip sizes shown in bold)
Air Cap Pattern
12"
NEW! Anodized
Finish
WaterborneCompatible
Gravity Guns Gravity Guns 1312
•Multiplefluidtipsincludedineachmodel
•Highgradestainlesssteelparts
•Easytoclean,blueanodizedfinish (FLG-670,FLG-671,andFLG-678)
•Provenreliability
Finishline® Spray Guns
803558 FlG-670 Solvent Base value kit includes: •900ccAluminumcup•1.3mmfluidtip•1.5mmfluidtip•1.8mmfluidtip•Airadjustingvalve
with gauge
803559 FlG-671 Waterborne value kit includes:•20oz.Acetalcup•1.3mmfluidtip•1.5mmfluidtip•1.8mmfluidtip•Airadjustingvalve
with gauge
803560 FlG-678 Primer value kit includes: •900ccAluminumcup•1.8mmfluidtip•2.2mmfluidtip
FinishLine® Gravity Feed Air Caps#1 air cap Primers, base coats, clearcoats, Conventional single stage and low VOC(opitonal) AirCapOrderNo. 690000 AirCapModelNo. FlG-1-1 9.9 CFM @ 40 PSI inlet
#3 air cap Primers, base coats, clearcoats, (HVlP) single stage and low VOCIncluded AirCapOrderNo. 690001 AirCapModelNo. FlG-1-3 13 CFM @ 23 PSI inlet
Fluid Tips 1.3 mm, 1.5 mm, 1.8 mm, 2.2 mm
FinishLine® Gravity FeedOrder no. model no.
Fluid tip (mm) Aircap Cup Application
803558 FlG-670
1.3, 1.5, 1.8
HVLP #3
900ccAluminum
Topcoats,lightprimers
803559 FlG-671
1.3, 1.5, 1.8
HVLP #3
20oz.Acetal
Waterbornetopcoats,lightprimers,primers
803560 FlG-678
1.8, 2.2 HVLP #3
900ccAluminum
Primers,liquidmasking,chipguards,other specialtymaterials
Cnv. = Conventional
Air Cap Pattern
10½"
Air Cap Pattern
10½"
FLG4PrimEr Gun vALuE KitOrder No.803560Model No.FlG-678
FLG4HvLP WAtErBOrnE vALuE KitOrder No.803559Model No.FlG-671
FLG4HvLP SOLvEnt-BASED vALuE KitOrder No.803558Model No.FlG-670
ALWAYS THE PRICE AND
PERFORMANCE LEADER
*Waterbornecompatiblewhenusingaplasticordisposablecupsystem.
WaterborneCompatible
WaterborneCompatible
WaterborneCompatible
Gravity Guns Gravity Guns 1514
HvLP Auto Painting Gun Sets
Specifications
StartingLine® HVLP Auto Painting Gun Kits
Order no. KitGuns
includedFluid tip
Cup(s) included
Accessories included
802342 Painting and Detail
Finish CoatDetail
1.31.01.8
One600cc(20oz.)One250cc(8.5oz.)
Cleaning brushes, wrench,air adjustingvalve with gauge
802343 2-Gun Painting and Priming
Finish CoatPrimer
1.31.81.5
Two600cc(20oz.)
Cleaning brushes, wrench,air adjustingvalve with gauge
802789 3-Gun Painting and Priming
Finish CoatPrimerDetail
1.31.81.0
Two600cc(20oz.)One130cc (4oz.)
Cleaning brushes, wrench,air adjustingvalve with gauge
803485 2-Gun Primer Pack
Primer(2) 1.51.8
Three3oz.plastic; Four24-oz.liners & lids, One sleeve, Two plugs
Two DPC-81 adapters, 1.5tip&needle
802405 Detail Gun only 1.0 One250cc (8.5oz.)
None
HVLPDetailSprayGun
2-Gun PrimerPack
HVLPFinishCoatSprayGun
HVLPPrimer SprayGun
Finish Coat and Primer Spray Gun
30PSIinletpressuredelivers10PSIaircappressureat13CFMairvolumeAirinlet:¼"NPS
Detail Spray Gun
30PSIinletpressuredelivers10PSIaircappressureat8CFMairvolumeAirinlet:¼"NPS
Detail gun also sold
separately
Gravity Guns Gravity Guns 1716
192219
Gravity Spray Gun Holders
Spray Gun Accessories
GH-505&GH-56
Gravity Gun Holders180029 MixingBenchGunHolder GH-505 Featuresasturdy,notipdesignforuseonpaint mixingbenches
180026 Paint Strainer Holder GH-56 AttachestotheGH-505toalloweasierpouringand mixingthroughapaintstrainer
192219 Wall Mount Gun Holder Protectivecoatingpreventsscratchesongravitycups
130095 / HAF-507-K2Whirlwind filter
803291 / HAV-555Digitalpressuregauge
220052 / HA-58673 ⁄8"HVLPairhoseassy.(35´)
803236 / HAV-512Airadjustingvalvewithgauge,100 PSI
m1-GHvLP GrAvity FEED Gun/CuPOrder No.901210Model No.6924-0000-0
Proven Performancelow air volume requirementsQuality finishes with low to medium solids materials
M1-G HVLP Gravity Feed Order No. Fluid inlet Air Model No. Tip (mm) Pressure Applications901210 1.4 18PSI Basecoats,clearcoats, 6924-0000-0 single stages, waterbornes (94x93P)
M1-G Gravity Gun includes:•1.4mmfluidtip•900ccaluminumcupwithpushonlid
•Spraygunlube,fluidfilter,gunhook
M1-G Gravity Feed HVLP Air Cap93P air cap Base coats, clearcoats, single stage, waterbornes AirCapOrderNo. 900361 AirCapModelNo. 46-9300 10 CFM @ 18 PSI inlet
Fluid tips 1.2mm(92),1.3mm(93), 1.4 mm (94), 1.7mm(97) (included tip size shown in bold)
Air Cap Pattern
10"
19Gravity Guns18 GravityGunAccessories
Gravity CupsCups to Fit DeVilbiss, Binks, Finishline and TEKNA Gravity Spray Guns
81-381 54-4458
SRI-478-K12GFC-501
Gravity Feed CupsOrder no. model no. Cup Size Application190252 GFC-501 20oz.
AcetalAllfullsizecurrentDeVilbiss,BinksandFinishLinegravityguns
803510 DPC-503-K24 3oz. Disposable
Fits onto any gun withaDeKupsadapter
192191 SRi-478-K12 4oz. Nylon
DeVilbiss SRi, SRiW, SRiPro, and BinksCubgravityguns
702576 702576 900cc Aluminum
Allfull-sizecurrentDeVilbiss,BinksandFinishLinegravityguns
901430 81-381 8oz. Aluminum
DeVilbiss SRi, SRiW, SRi Pro and BinksCubgravityguns
900875 54-4458 4oz. Aluminum
DeVilbiss SRi, SRiW, SRi Pro and BinksCubgravityguns
702576
DPC-503-K24
Gravity Cups
StartingLine Gravity Feed CupsOrder No. Model No. Cup Size Application802346 600 CC StartingLine Finish Coat and Primer 802346 Aluminum gravity guns 802347 250 CC StartingLine Detail gravity guns 802347 Aluminum
802346 802347
StartingLine®
GrAvity CuPS
E-Z LinersOrder no. model no. Description190966 OMX-70-K48 E-Z Liner Kit
(48liners&bushings)
192177 OMX-70-K10 E-Z Liner Kit (10liners&bushings)(orderqty.12)
E-Z Liners
OMX-70-K10
Most Economical Disposable Paint Cup System Available• Savespainterstimewitheasy cleanupandlessmess
• Savesshopsmoneybygreatlyreducingsolventuseforcleanup
GravityCups GravityCups 2120
Suction Guns&Accessories
Air Cap Pattern
10"
JGA®
COnvEntiOnAL SuCtiOn FEED Gun/CuP Order No.110225Model No.JGA-644
Order No.110102Model No.JGA-636
JGA® Suction Gun includes:•TGC1-qt.cup
DeVilbiss JGA® Suction Feed GunsOrder No. Fluid inlet Model No. Type Tip (mm) Pressure Application
110225 CNV. 1.6 35-50PSI Base,clear,lowVOC,single JGA-644 stages, Urethanes
110102 CNV. 1.8 25-45PSI Syntheticandacrylicenamels JGA-636 Mayneedtorestrictfluidflow withneedleadj.forbaseand CNV. = Conventional clearcoats.
Proven Technology and Durability
JGA® Conventional Suction Feed Air Caps#9000 air cap Base coats, clearcoats, single stages JGA-644 AirCapOrderNo. 199000 AirCapModelNo.AV-440-9000 35-50 PSI inlet 9-13 CFM Fluidtips 1.6mm,1.8mm
#80 air cap Synthetic and acrylic enamels JGA-636 AirCapOrderNo. 190230 AirCapModelNo.MB-4039-80 25-45 PSI inlet 10-14 CFM Fluidtips 1.8mm
Air Cap Pattern
12"
SuctionGuns 2322
EGA™ Suction/Pressure Feed Touch-up GunOrder No. Fluid inlet Model No. Type Tip (mm) Pressure Application
110222 CNV. 1.0 30 PSI All automotive EGA-503-390F refinishing materialsCnv. = Conventional
EGA™
COnvEntiOnAL SuCtiOn/PrESSurE FEED tOuCH-uP GunOrder No.110222Model No.EGA-503-390F
EGA™ Conventional Suction or Pressure Feed Touch-up Air Cap#390 air cap General Purpose AirCapOrderNo.190083 AirCapModelNo.EGA-40-390 30 PSI inlet 3 CFM
Fluid tip 1.0 mm
Air Cap Pattern
3"
Patented “Drip Free Design” – One Quart Capacity
TGC-545
Suction Feed CupsOrder No. Model No. Cup size Application120011 1qt. AllfullsizecurrentBinks,DeVilbiss TGC-545 Aluminum andFinishLinesuctionguns120038 8oz. DeVilbissEGA&EGHVsuctiontouch-upguns TGS-503 Polyethylene
Suction Feed Cups
TGS-503
Durable Detail Suction Cup
PLUS® Suction Feed GunOrder No. Fluid inlet Model No. Type Tip (mm) Pressure Application
110265 High 1.6 30-40PSI BasecoatsJGA-670 Efficiency 35-45PSI Highandlowsolidsclearcoats 35-45 PSI Single stages 1.8 30-40PSI Syntheticandacrylicenamels
PLuS®
HiGH EFFiCiEnCy SuCtiOn FEED Gun/CuPOrder No.110265Model No.JGA-670
PluS® Suction Gun includes:•1.6mmand1.8mm fluidtips
•TGC1-qt.cup•Highoutputairadjusting
valve with gauge•Spraygunlube
PLUS® Suction Feed High Efficiency Air Cap#410 air cap Primers, base coats, clearcoats, single stage, and low VOC AirCapOrderNo. 192174 AirCapModelNo. AV-440-410 30-40 PSI 9-11 CFM
Fluid tips 1.0 mm, 1.2 mm, 1.3 mm, 1.4 mm, 1.6 mm, 1.8 mm (included tip sizes shown in bold)
Air Cap Pattern
12"
NEW! Anodized
Finish
SuctionGuns SuctionGuns 2524
GTi® Suction Gun includes:•2.0mmand2.2mm fluidtips
•TGC1-qt.cup•Highoutputairadjusting
valve with gauge•Spraygunlube
GTi® Millennium HVLP Suction Feed GunOrder No. Fluid inlet Model No. Type Tip (mm) Pressure Application
170161 HVLP 2.0 20-25PSI BasecoatsGTi-620S 2.2 25-30 PSI Low and high solids, clearcoatsandsinglestages
Gti® milleniumHvLP SuCtiOn FEED Gun/CuPOrder No.170161Model No.GTi-620S
GTi® Millennium Suction Feed HVLP Air Cap#2000 air cap AirCapOrderNo.192136 (HVlP) AirCapModelNo.GTi-407-2000 20-30 PSI 12.5-16 CFM
Fluid tips 1.0 mm, 1.2 mm, 1.3 mm, 1.4 mm, 1.5 mm, 1.6 mm, 1.8 mm, 2.0 mm, 2.2 mm (included tip sizes shown in bold)
Air Cap Pattern
11"
Pressure Guns & Tanks&Accessories
NEW! Anodized
Finish
27SuctionGuns26
Order No.170159Model No.GTi-520P-11
Order No.170165Model No.GTi-546P-14
Gti® milleniumHvLP PrESSurE FEED Gun
HVlP Technology with large Spray Pattern• Smoothmaterialandairflow• Easytoclean• Produceahighglossfinishand minimizeorangepeel
• Excellentfluidcontrolforapplying morefilmbuildwithfewerpasses
Air Cap Pattern
12"
Air Cap Pattern
11"
GTi® Millennium Pressure Feed HVLP Air Caps#2000 air cap Primers, base coats, clearcoats, (HVlP) and low VOC AirCapOrderNo. 192136 AirCapModelNo. GTi-407-2000 20-30 PSI 12.5-16 CFM
#46MP air cap Primers, base coats, clearcoats, (HVlP) single stages and low VOC AirCapOrderNo. 192184 AirCapModelNo. GTi-407-46MP 50 PSI inlet 22.5 CFM
Fluid tips 1.1 mm, 1.4 mm
GTi® Millenium Pressure Feed GunsOrder No. Fluid inlet Model No. Tip (mm) Pressure Application Fluid Flow
170159 1.1 30PSI Lowtomediumsolids 7-12oz./min. GTi-520P-11 1.1 30PSI Highsolids 5-7oz./min.
170165 1.4 50PSI Highsolids 9-12oz./min. GTi-546P-14
NEW! Anodized
Finish
Order No.802942Model No.CVi-501-510-10
Cvi®
PrESSurE FEED Gun
CVi® Pressure Feed GunOrder No. Fluid inlet Model No. Tip (mm) Pressure Application Fluid Flow
802942 CVi-501-510-10
#510 (HE) 1.0,1.4 25-29PSI Mediumtohighsolids 7-10oz./min.
#505 (HVlP) 1.0,1.4 14-18PSI Basecoats,lowto 6-8oz./min. medium solids
CVi® Pressure Feed Air Caps#510 air cap Primers, base coats, clearcoats, (HE) single stage, and low VOC AirCapOrderNo. 802546 AirCapModelNo. SP-100-510-K 20-29 PSI inlet 7.5-9 CFM
#505 air cap Base coats, clearcoats, primers, (HVlP) single stage, and low VOC
AirCapOrderNo. 802841 AirCapModelNo. SP-100-505-K 14-18 PSI inlet 10-13 CFM
Fluid tips 1.0 mm, 1.2 mm, 1.3 mm, 1.4 mm (included tip sizes shown in bold)
Air Cap Pattern
11¼"
Air Cap Pattern
11½"
WaterborneCompatible
• Twoaircapsandfluidtip sets included
• Comfortableand lightweight, ergonomic design reduces fatigue
• Spraysabroadrange of materials
Pressure Guns Pressure Guns 2928
PLUS® High Efficiency Pressure Feed GunsOrder No. Air Fluid inlet Model No. Cap Tip (mm) Pressure Application Fluid Flow
110266 #410 1.0 30-50PSI Mediumsolids 6-10oz./min. JGA-570-10 25-35PSI Enamelsandprimers
110272 #414 1.2 60-65PSI Highsolids 7-14oz./min. PluS-514P-12
PLuS®
HiGH EFFiCiEnCy PrESSurE FEED GunOrder No.110266Model No.JGA-570-10
Order No.110272Model No.PluS-514P-12
High Efficiency
Superior Atomization
Handles Difficult Materials and Delivers Superior Finishes
PLUS® Pressure Feed High Efficiency Air Caps#410 air cap Primers, base coats, clearcoats, single stage, and low VOC AirCapOrderNo. 192174 AirCapModelNo. AV-440-410 30-50 PSI 9-12 CFM Fluidtip 1.0mm
#414 air cap High solids AirCapOrderNo. 192312 AirCapModelNo. AV-440-414 60-65 PSI inlet 19-22 CFM Fluidtip 1.2mm
Fluid tips 1.0 mm, 1.2 mm, 1.3 mm, 1.4 mm
Air Cap Pattern
12½"
Air Cap Pattern
11–14"
JGA®
COnvEntiOnAL PrESSurE FEED Gun
Order No.110271Model No.JGA-504-765-12
Order No.110274Model No.JGA-504-777-14
High Production High Performance• Worldwidechoiceforlargearea refinishing
JGA® Conventional Pressure Feed Air Caps#765 air cap High solids AirCapOrderNo. 192310 AirCapModelNo. AV-440-765 60-65 PSI inlet 19-22 CFM Fluidtip 1.2mm
#777 air cap High solids AirCapOrderNo. 192066 AirCapModelNo. AV-440-777 50-80 PSI inlet 17-25 CFM Fluidtip 1.4mm
Fluid tips 1.0 mm, 1.2 mm, 1.3 mm, 1.4 mm
Air Cap Pattern
11–14"
Air Cap Pattern
11–14"
JGA® Conventional Pressure Feed GunsOrder No. Air Fluid inlet Model No. Cap Tip (mm) Pressure Application Fluid Flow
110271 #765 1.2 60-65PSI Highsolids 7-13oz./min. JGA-504-765-12 Fleet materials
110274 #777 1.4 50-80PSI Highsolids 9-17oz./min. JGA-504-777-14 Fleet materials
NEW! Anodized
Finish
Pressure Guns Pressure Guns 3130
Pressure tanks and Cups
83C-220 83C-221
Heavy-duty, A.S.M.E. Code Pressure Tanks Comply with O.S.H.A. Regulations• 2.7and9.8galloncapacity• Availableinsingleand
double regulated versions• Quick,efficientcleanup withanti-statliners(p.33)
Pressure Cups and Tanks
Order no. model no. Capacity regulation¾ H.P. Air Driven Agitation included
901558 83C-210 2.7 gal. Single No901560 83C-220 2.7 gal. Double No901561 83C-221 2.7 gal. Double Yes120033 KB-555 2qt. Yes N/A930780 183G-520 9.8 gal.* Double No(availableseparately,
orderQMG-418&QS-5012)
PrESSurE CuP, 2-QuArt
Order No.120033Model No.KB-555
183G-520
KBii 2-qt. is comfortable to carry. Easy clean ups with disposable liners
KBii Worldwide Favorite
KB-555 KBII
KBII AccessoriesOrder No. Model No. Description
220019 KB-4006 Hoseassembly,6ft.192025 KK-5051 KBEZLinerkit
*183G-520holdsa5gallonpail
9.8 Gallon* A.S.M.E. Code Pressure Tank
PTL-406-K20
Pressure tank Liners
PT-52 / PT-52-K6080-356
Quick, Efficient Clean up with Anti-Stat liners
Pressure Tank LinersOrder no. model no. Description
192143PT-52
TankLiner(orderquantity10)
192153PT-52-K60
TankLiner
191696PTl-406-K20
TankLiner
Pressure Tanks and Cups
83B 83C
183G-520 83G-520 83G-500
2 Qt. Cup Steadi-
Grip
83- 5600 83-
15600
83- 5500 83-
15500 83-
5400
XX
X
XXX
XX
Tank Liners
Fits Tank Size
Case Qty.
DeV
ilbis
s PT-52 2.7 gal. 10PT-52-K60 2.7 gal. 60PTL-406-K20 9.8 gal.* 20PTL-410-K8 11.8 gal. 8
Bin
ks
80-356 2qt. 1283-2878 2 gal. 126-228-60 2 gal. 606-238-60 2 gal. 606-239 5 gal. 24
Tank Liners
Fits Tank Size
Case Qty.
DeV
ilbis
s PT-52 2.7 gal. 10PT-52-K60 2.7 gal. 60PTL-406-K20 9.8 gal.* 20PTL-410-K8 11.8 gal. 8
Bin
ks
80-356 2qt. 1283-2878 2 gal. 126-228-60 2 gal. 606-238-60 2 gal. 606-239 5 gal. 24
Pressure Tanks
All PT Series Tanks
QMGT- 5200
QMST- 5200
QMGT- 5500
QMST- 5500
QMGT- 51000 QMST- 51000
X XX X
XX
*183G-520holdsa5gallonpailDeVilbissPT-52seriestanklinersalsofitBinks83Band83CtankseriesDeVilbissPTL-406seriestanklinersalsofitBinks83G-500tankseriesBinksPTL-408seriestanklinersalsofitDeVilbissQMGT-5500andQMST-5500tankseries
PressureTanks PressureTanks 3332
Disposable Cups&Accessories
Pressure Gun Accessories
FLuiD rEGuLAtOr
Order No.130090Model No.HGS-5242
FLuiD FiLtEr
Order No.180073Model No.VS-532
FLuiD tuBE
Order No.180042Model No.JGA-444
KB ADAPtEr FittinG AnD HOSE Kit
Order No.192026Model No.KK-5052
SOLvEnt SAvEr
Order No.180037Model No.HD-503
A Real Time SaverCleansfluidhosesquickly without wasting solvent
•3/8"NPSthread
•Keepshosefromdragging over workandpreventstwisted lines
•3/8"NPS(M) fluid inlet
•3/8"NPS(F) swivel fluid outlet
•Regularpressure from2-50PSI
Allowsflushingofcuptube,hoseand gun using SolventSaver™. Kit includes:HD-410adapterfitting and 2' hose assembly.
28
KB II
Solvent Saver™
35PressureGunAccessories34
1
5 6
7 8 9
32
10 11 12
4
DeKups®
GrAvity FEED DiSPOSABLE CuP
Gun not included
24 oz.
34 oz.
9 oz.
The ultimate in ProductivitySaves Time and Money• Betterfluidflowfor greatcolormatch
• Positivelocking gunconnection
• Refillwithoutopening thecup
• Self-dispensingpackaging• Largercapacitycups
Available in 9, 24, 34oz.
U.S.PatentNos.6,820,824and7,374,111,ownedby3MInnovativePropertiesCo.,and U.S.PatentNos.7,380,680;7,354,074;7,353,964;7,350,418;7,344,040;7,263,893;7,165,732;7,086,549;ownedbyIllinoisToolWorksInc.
improved Reusable Sleeve
for Better Grip
DisposableCups DisposableCups 3736
DeKups® Demo KitOrder No. Model No.803130 DPC-654
Get Started with DeKups Today!The ultimate in ProductivitySaves Time and MoneyAnti-Static Disposables•Containstheperfectamountforseveraljobs•Betterfluidflowforgreatercolormatch•Positivelockinggunconnection•Anti-staticcupsforimprovedmetallicdistribution•Largercapacitycups
802212 / DPC-44Cleaning brush
192316 / DPC-8Cleaning bottle
802950 / DPC-59-K1024oz.Universalmeasuringguide(10)
802951 / DPC-60-K109oz.Universalmeasuringguide(10)
802952 / DPC-61-K1034oz.Universalmeasuringguide(10)
802953 / DPC-62-K1024oz.2:1and3:1Measuringguide(10)
802954 / DPC-63-K1024oz.4:1and5:1Measuringguide(10)
802334 / BXX-1279Filters&plugs storagecase
802109 / DPC-22-K24Disposablefunnel(24)
803474 / DPC-524Disposablelid(32)
Accessories
DeKups® Disposables and ReusablesOrder No. Model No. Description
802102 DPC-602 9FL.OZ./265mlDisposablecup/lid(32)
802101 DPC-601 24 FL. OZ./710 ml Disposablecup/lid(32)
802100 DPC-600 34 FL. OZ./1000 ml Disposablecup/lid(32)
802972 DPC-607 9FL.OZ./265mlReusablesleeve/lid(2)
802759 DPC-606 24 FL. OZ./710 ml Reusablesleeve/lid(2)
802973 DPC-608 34FL.OZ./1000mlReusablesleeve/lid(2)
803474 DPC-524 24 FL. OZ./34 FL. OZ. Disposablelid(32)
9 oz. DPC-602 & DPC-607
34 oz. DPC-600
& DPC-608
24 oz. DPC-601 & DPC-606
U.S.PatentNos.6,820,824and7,374,111,ownedby3MInnovativePropertiesCo.,and U.S.PatentNos.7,380,680;7,354,074;7,353,964;7,350,418;7,344,040;7,263,893;7,165,732;7,086,549;ownedbyIllinoisToolWorksInc.
U.S.PatentNos.6,820,824and7,374,111,ownedby3MInnovativePropertiesCo.,and U.S.PatentNos.7,380,680;7,354,074;7,353,964;7,350,418;7,344,040;7,263,893;7,165,732;7,086,549;ownedbyIllinoisToolWorksInc.
Demo Trial KitAdapterforDeVilbissTEKNA/Finishline/Binks(1), 24oz.ReusableSleeve&Lid(1),24oz.DisposableCups&Lids(8),Plugs(5),DiskFilter125Micron(4),BarrelFilter300Micron(1),Funnel(1),MeasuringGuide(1),How-to-UseGuide
DisposableCups DisposableCups 3938
•Simpleandaffordablesolutionforspotrepairandsprayingat mobile repair locations
•Ventedcupdesignprovidesconsistentfluidflowforbettercolor match and a better quality finish
•EasyandsecurefitoverDPCadapters
LID
CUP
DPC ADAPTER(not included)
OPTIONAL FILTER(not included)
DeKups® Shop Start up KitOrder No. Model No.802371 DPC-650
U.S.PatentNos.6,820,824and7,374,111,ownedby3MInnovativePropertiesCo.,and U.S.PatentNos.7,380,680;7,354,074;7,353,964;7,350,418;7,344,040;7,263,893;7,165,732;7,086,549;ownedbyIllinoisToolWorksInc.
3 oz. Disposable CupOrder No.803510Model No.DPC-503-K24 (Kitof24cups&lids)
Shop Start up Kit24oz.ReusableSleeve&Lid(3),9oz.ReusableSleeve&Lid(1), 24oz.DisposableCups&Lids(32),9oz.DisposableCups&Lids(32),24/34oz.DiskFilter125Micron(12),9oz.DiskFilter125Micron(12),BarrelFilter300Micron(10),BarrelFilter600Micron(10),Funnel(24),3oz.DisposableCups(3),CleaningBrush,CleaningBottle,Magnets(5),How-to-UseGuide
DisposableCups DisposableCups 4140
802976 / DPC-42-K2424oz./34oz.Diskfilter (125micron)(24)Whiteframe/whitemesh
802978 / DPC-66-K2424oz./34oz.Diskfilter (200micron)(24)Blackframe/whitemesh
802977 / DPC-65-K249oz.Diskfilter (125micron)(24)Whiteframe/whitemesh
802979 / DPC-67-K249oz.Diskfilter (200micron)(24)Blackframe/whitemesh
Disk Filters
Adapters
Foradditionaladaptersseewww.autorefinishdevilbiss.com
802204 / DPC-11Adapter(SataNR95&92,IwataLPH-400 & W400LV, Astro GF14, 17 & 20S, FinexFX200&FX300)
802205 / DPC-13Adapter(Sagola)
802201 / DPC-26Adapter(AccusprayIssac)
802202 / DPC-31Adapter(FinishLine2,3&4)
802200 / DPC-43Adapter(DeVilbiss, TEKNA, CVi, PLUS,GTi,PRi,JGA,BinksM1G,SharpeCobalt,Platinum&Titanium)
802203 / DPC-10Adapter(Sata NR 2000, RP, KLC, MCB &Jet90series)
802206 / DPC-23Adapter(DeVilbiss SRi, SRiW, SRiPro, and BinksCub)
Get started today!Order adapters from
your distributor
Adapters
Barrel Filters802107 / DPC-17-K10Finefilter(300micron) Colorsandclears(10)
802108 / DPC-27-K10Very fine filter (200 micron)Pearls(10)
802106 / DPC-14-K10Coarsefilter(600micron) Thickpaint(10)
803238 DPC-502AdapterKit(SataMinis,QCC&threaded)
802955 / DPC-64Adapter(StartingLinetouch-upgun)
803237 / DPC-501AdapterKit(SataQCCfullsize)
802340 / DPC-500ConversionAdapter
803120 / DPC-69-K1SuctionConversionKit
803420 / DPC-81Adapter(StartingLinefull-sizegun,SharpeFinex 1000, 2000, 3000)
803314 / DPC-78Adapter(IwataSuperNova, AirGunsa,LPH300,W300)
Foradditionaladaptersseewww.autorefinishdevilbiss.com
U.S.PatentNos.6,820,824and7,374,111,ownedby3MInnovativePropertiesCo.,and U.S.PatentNos.7,380,680;7,354,074;7,353,964;7,350,418;7,344,040;7,263,893;7,165,732;7,086,549;ownedbyIllinoisToolWorksInc.
U.S.PatentNos.6,820,824and7,374,111,ownedby3MInnovativePropertiesCo.,and U.S.PatentNos.7,380,680;7,354,074;7,353,964;7,350,418;7,344,040;7,263,893;7,165,732;7,086,549;ownedbyIllinoisToolWorksInc.
DisposableCups DisposableCups 4342
Airbrushes
nAirbrushesandAccessoriesPackages –featuringDAGR®
nCompressorsandAccessoriesPackages –featuringAirBlade®
nAirbrushTemplates –fromdesignersAlanPastranaandScottMcKay
&Accessories
Cups, Lids & AdaptersOrder no. model no. Description Qty/Pkg803431 DMK-621 24oz.cup/filterlid–125micronbluefilter 48803432 DMK-622 24oz.cup/filterlid–200microngreenfilter 48803433 DMK-26 Storagelid,24oz.cup 48803434 DMK-421 Filterlidfor24oz.cup–125micronfilter 48803435 DMK-422 Filterlidfor24oz.cup–200micronfilter 48803436 DMK-110 Adapter,SataNR2000&RP803437 DMK-111 Adapter,SataNR92/95,Iwata400803438 DMK-143 Adapter,DeVilbiss,Binks&Sharpe803439 DMK-178 Adapter,IwataSuperNova&W300803440 DMK-181 Adapter,StartingLineFullSize803442 DMK-1500 ConversionAdapter,3M803570 DMK-1501 ConversionAdapter,Sata
Gunner Cups• Integrated air-flow
valve allows for a consistent paint flow. Excellent for waterborne.
• Flat lid available for easy stacking and storing.
• Extensive range of paint company-specified mixing ratios.
• Increase shop productivity and profits with the easy to use design.
• Save time and money on cleaning solvent and disposal.
Mix.
Flow.
Store.
45DisposableCups44
Order No.802609Model No.DGR-501G-35
DAGr®
GrAvity AirBruSH (.35mm)
DAGr® Studio
Performance and Versatility for the Automotive Artist
ExcellentControl•Hairlinedetailtohighpaint-flowshadingandgradualfades
•Smoothdoubleactiontrigger•Pre-sethandleforprecisecontrolofpaintflow
Versatile•Spraysautomotivepaintstowaterbasedinks
•Removable1⁄3oz.gravitycupwithoptional¼oz.and½oz.cupsavailableorspraywithnocup
•Threadedareaonpre-sethandleforcrowncapwhenremovedduring use
Durable•Solventprooffluidpassages•Copper,nickelandchrome platedbody
Order No. Model No.803125 DGR-603
Everything the Automotive Artist needs to get started!•DAGRairbrushwith1/3oz.cup•½fl.oz.(14cc)cupandlid–idealforsprayinglargerareas
without refilling•10ft.braidednylonairhose
Comfortable•Lightweightandbalanced•Choiceoftriggerbuttons
High Quality•PrecisionmadeinU.S.A.
Value•Crowncapstandardforfinelinesandneedleprotection
•Collectorstoragetinincluded
Order No803285
Model No.DGR-604G-35
DAGr®
GrAvity AirBruSH, 1⁄8 HP COmPrESSOr AnD HOSE
AirBlade® Compressor and AccessoriesOrder No. Model No. Description
803286 DGR-518-1 AirBlade®Compressorw/Regulator(1⁄8hp) .07CFM,upto30PSI,120V803287 DGR-140 Regulatorw/filter,moisturetrap,hanger803285 DGR-604G-35 Gravity DAGR®w/Compressor(1⁄8hp),hose
DGR-518-1
AirBlade® Compressors include:•Regulator•Watertrapfilter•Airbrushholder
Quiet, Oilless, Piston Compressor with Automatic Shut-Off for longer Compressor life
AirBlade®
COmPrESSOr WitH rEGuLAtOr (1⁄8 HP)Order No.803286
Model No.DGR-518-1
WaterborneCompatible
Airbrushes Airbrushes 4746
GO
TT
A H
AV
E ’
EM
™ S
ET
1
GO
TT
A H
AV
E ’
EM
™ S
ET
2
GO
TT
A H
AV
E ’
EM
™ M
INIS
ON
FIR
E!™
KE
WL
EF
X™
SIX
-PA
CK
O’S
KU
LL
Z™
Templates designed by renowned artists Alan Pastrana and Scott MacKay•Precision,laser-cuttemplatesforhighlydetailedeffects•Solventproof!Greatwithbothsolventandwater-basedpaints•Savetimecuttingfrisketoracetatemasks.Nosoftware orplottersneeded.
•Loadedwithextrasforcreatingfinishedfreehand-styleartwork•Positivesandnegativesforpaintingonlight ordarkbackgrounds
•Usewithanyairbrush,includingtheDeVilbissDAGR®
Pastrana Templates
Order no. model no. Description803278DGR-133
GottaHave’Em™ set 1 (5templates)FrenchCurve,BigGhost1,Ham-merhead,Spider,MiniGhost2*
803279DGR-134
GottaHave’Em™ set 2 (4templates)Ship’sCurve,BigGhost3,Waves‘n’Curves,MiniWaves‘n’Curves*
803280DGR-135
GottaHave’Em™ Minis (7templates)Mini Ghost 1, Mini Ghost 2, Mini Ghost 3, Mini Ghost 4, Mini Waves‘n’Curves,MiniHam-merhead,MiniSpider
803281DGR-136
OnFire!™(5templates)BringingtheHeat,Burning Down, Fuego, Round Fire, MiniHammerhead*
McKay Templates803282DGR-137
Six-PackO’Skullz™ set 1 (6templates)Medium:HeadDown,SayAh,OldYeller;Large:SideLook,LookUp,SayWhat
803283DGR-138
Six-PackO’Skullz™ set 2 (6templates)Medium:SideLook,LookUp,SayWhat;Large: HeadDown,Say Ah, Old Yeller
803284DGR-139
Kewl Metal EFX™ (3templates)DiamondPlate;Nutz,Screwz,‘n’Rivets™;Hazardous‘n’More™
* Bonus template
n includes: DesiccantDryerSystems,AirFiltrationSystems,HoseandFittings,AirAdjustingValves,AirRegulators,Respirators,BreathableAir Systems
AirControl
49Airbrushes48
Ct Plus™ 5-StAGE DESiCCAnt FiLtEr SyStEmOrder No.130522
Worry free air filtration for top quality paint jobs•Firststagefilterremoves
oil, water and dirt down to 40micron
•Secondstagecoalescerremovesoilvaporsanddirtparticlesdownto.01micron
•CT30desiccanttankrepeatsdirt and oil aerosol removal and removes humidity
•Installatpointofuse
30 CFM capacity at 100 PSi
Easy and economical maintenance•Longerdesiccantlife•Airinletvalveshutsoff
CT Plus™ air without having toshutoffshopair
•Notoolsneededtochangefirstandsecondstagefilters
•Easychange-outdesiccantcartridgebag
Ergonomic, self-relieving regulator
CamAir® CT Plus™
Order no. Description
130522 CTPlus5-stagedesiccantfiltersystem130517 Filterelement,water(1stStage)130518 Filterelement,coalescing(2ndStage)130504 DC30desiccantcartridge130516 Regulator assembly
Water Separator
Oil Coalescer
2-Stage Filter SystemOrder No.130523
CamAir® Filter SystemsOrder no. Description130523 2-stage filter unit with regulator130526 3-stage filter unit with 2 regulators130517 Filterelement,water(1stStage)130518 Filterelement,coalescing(2ndStage)130527 Filterelement,charcoal(3rdStage)
Air Filtration/Regulation Systems •Compactandeffective—perfectforcrampedshopspaces•Removesdirt,waterandoilfromairlinesto0.01micron—assuressuperiorfinishes
•Quickchangebowlsandairinletvalveaccommodaterapid,troublefreemaintenancewithoutshuttingoffmainshopair
•Combine2-stagefilterwiththeCT-30desiccantdryertocreate a CT Plus 5-stage filter system
65CFMCapacity@90PSI
Water Separator
Oil Coalescer
CharcoalAdsorber
Water Separator
Oil Coalescer
3-Stage Filter SystemOrder No.130526
3-STAGE FILTER SYSTEM MEETS TYPE 1 GRADE D BREATHABLE
AIR PARTICULATE REQUIREMENTS
WaterborneCompatible
WaterborneCompatible
Air Filtration Air Filtration 5150
Patents Pending
Easy Change Desiccant Air Dryer
Ct30 & Ct30PDESiCCAnt CArtriDGE DryErS
•CTseriesdesiccantairdry-ersremovewatervaporfrom thecompressedairdown toadewpointof-40°F
•Quickchange10lb. desiccantcartridgebag ismadeofaspecialfibermediawhichremovesoilaerosolsandsolidparticlesdownto0.1micron—meaningnoneedforcoalescingorfinalfilters
• Installatpointofuse
Order No. 130500 (CT30 WallMount)Order No. 130501 (CT30-P Portable)
Patent No. 7361214
130501(CT30-P)
CT Desiccant Cartridge DryerOrder No. Description130500 DesiccantAirDryerwall mount130501 DesiccantAirDryerportable with stand130504 Desiccantcartridge
30CFMairflowcapacity
QC3FiLtEr AnD DryEr unitOrder No. 130525
130525
130524
light Duty, Compact Air Filter/DryerA great choice for light usage such as low volume shops, restorers, customizers, and hobbyists• Three-stagefilteringwith0.1micronratingproducesclean,oil-andhumidity-freeair.
•Highperformancefiltrationwithonly2PSIpressuredrop.•Quickchangefiltercartridgeiseasytomaintain. Bowlremovaltoolincluded.
• Largerfiltermediaandlongerlifedesiccantthan disposabledryers
QC3 Desiccant Cartridge DryerOrder No. Description
130525 DesiccantFilterandDryerUnit130524 QC3FilterandDesiccantCartridgeReplacement
16CFMairflowcapacity
COMPLETELY PORTABLE.
ALLOWS PLACEMENT AT POINT OF USE
The Value leader• Removesmoistureanddirt• Regulatesairpressure
FinishLine® Air Control unitOrder No. Model No.130099 HAR-602
includes:•5micronparticlefilter•Mountingbracket•Regulatorandgauge
FinishLine® Air Control UnitOrder No. Model No. Description130099 HAR-602 Aircontrolunit192315 HAF-39 Filterelementandgasketkit
120CFMairflowcapacityforfilter,50CFMairflowcapacityforregulator
DAD-500™ DESiCCAnt Air DryEr SyStEm
Compare the humidity reading before and after filtering with
DeVilbiss DAD-500
Compare DeVilbiss filtered air vs. unfiltered air
DeVilbiss’DAD-500filtersoutcontaminantsto.01micron
READiNG AFTER FilTERiNG
(.2%Relativehumidity)
READiNG BEFORE FilTERiNG
(70.2%Relativehumidity)
uNFilTERED AiR
Oil Dirt
Rust
FilTERED AiR
Avoid Costly RedosProperly maintained air filtration system eliminates moisture and dirt in air lines•Installatpointofuse•Cleanair=betterfinish
Desiccant Air DryerOrder No. Model No. Description
130026 DAD-500 3-stagedesiccantairdryersystem190831 DAD-1 Desiccantrefill130030 DAD-600 Desiccantrefill,1stStagefilterelement802182 DAD-600-1 Desiccantrefill,filterelementkit,1stand2ndStage filter elements
25CFMairflowcapacity
ALSO inCLuDES: ½" BALL vALvE
SHutOFF FOr EASy mAintEnAnCE
Air Filtration Air Filtration 5352
Air Filtration and Regulation Systems — Remove Dirt, Oil Vapor, and Water from Air lines
Clean Air™ Air LinE FiLtErS AnD COntrOL unitS
13-0042
Clean Air™ Air Line Filters and Control UnitsOrder No. Model No. Description
130098 Two-stage filtration system, HAF-518 includingcentrifugalandcoalescer w/ 60 CFM regulator
130041 100 CFM air line filter 13-0041 5micronfilter
130042 100 CFM air line filter 13-0042 w/ 60 CFM regulator
HAF-518
HAF-518 QuiCK FACtS:•1stStage5micronfilter•2ndStage.01micronfilter•Easiermaintenancecomes with manual flexible drain
130502 (DS20)
Alerts Painter to Humidity in the Air line
Recommended for use with Desiccant Snake
130503 (RHI-01)
Desiccant SnakeOrder No. Model No.130502 DS20
Humidity indicatorOrder No. 130503Model No. RHi-01
Disposable, in-line Desiccant Air Dryer
Desiccant Snake and IndicatorOrder No. Description130502 DS20DesiccantSnake130503 RHI-01HumidityIndicator
Automatic Drain with y-Strainer valveOrder No. 130512
Automatically drains water from compressed air systems•Usewithaircompressors,waterseparatorsandatdroplegs—Seeproperlypipedshopdiagramforinstalllocations(pgs.78–79)
•Adjustableintervaltimeanddraintime•Removablefilterforeasycleaning•Includeselectrictimer,¼"Y-strainervalvewithfilterscreenand6ft.powercord
•Auniquedesignthatcombines desiccantdryingwithbuiltindirt and oil aerosol filters
•EffectivewithbothHVLPand Conventionalsprayequipment
•200PSImaximum•150˚Fmaximum
rEmOvES Dirt, WAtEr AnD
OiL—PErFECt FOr LOW HumiDity
COnDitiOnS
Air Filtration Air Filtration 5554
Hoses
Air Hose Assemblies Hose Assembly Connection Conn. Size Order No. length Bulk Thread Type of Nut & i.D. Model No. of Hose Hose # Size Connection Nipple
5/16" 220002 25' H-1921 1/4"NPS(F) Three-Piece 240032 HA-2125 Swivel Reusable P-HC-4527
5/16" 220004 50' H-1921 1/4"NPS(F) Three-Piece 240032 HA-2150 Swivel Reusable P-HC-4527
3/8" 220049 25' H-1958 1/4"NPS(F) Three-Piece 240038 HA-5825 Swivel Reusable P-HC-4528
3/8" 220052 35' H-1958 1/4"NPS(F) Three-Piece HC-4719 HA-5867* Swivel Reusable P-HC-4528
3/8" 220054 35' H-1958 1/4"NPS(F) Three-Piece 240033 HA-5835 Swivel Reusable P-HC-4528
3/8" 220047 50' H-1958 1/4"NPS(F) Three-Piece 240033 HA-5850 Swivel Reusable P-HC-4528
*HA-5867HVLPAirHoseAssemblyincludes HC-4719HighVolumeAirQuickDisconnectandHC-4419Stem.
Fluid Hose Assemblies Hose Assembly Connection Conn. Size Order No. length Bulk Thread Type of Nut & i.D. Model No. of Hose Hose # Size Connection Nipple
3/8" 220008 25' H-1973-1 3/8"NPS(F) Three-Piece 240035 HA-7325 Reusable P-HC-4548
3/8" 220040 35' H-1973-1 3/8"NPS(F) Three-Piece 240035 HA-7335 Reusable P-HC-4548
3/8" 220045 50' H-1973-1 3/8"NPS(F) Three-Piece 240035 HA-7350 Reusable P-HC-4548
1/4" 220055 35' H-1975-1 3/8"NPS(F) Three-Piece 240034 HA-7535 Reusable P-HC-4543
Smooth Cover — Spray and Air Tool HoseCan be used for all kinds of air-operated equipment. Smooth brick-red cover, synthetic rubber compound tube with high tensile strength braid. Hose offers superior resistance to oil, weathering, ozone and abraision. Can be used with reusable or permanent crimp connections. Maximum application temperature: 150°F
Nyliner ii Fluid HoseIdeal for use with a wide range of materials such as resins and solvents contained in latices, epoxies, urethanes, alkyds, primers, acrylics, ketone, MEK, acetone, polyesters, silicones, bitumastic coatings, oil and water-based paints, lacquers, latex coatings, toluene, turpentine, naptha, and many other solvents. Tube is nylon; cover is black neoprene rubber; yarn reinforced. Can be used with permanent crimp or reusable connections. Maximum application temperature: 150°F
Air/Fluid Hose Set (for use with KBII Cup) Bulk Bulk Conn. Type Conn. Order No. Air Fluid Thread of Nut & Model No. length Hose Hose Size Conn. Nipple
220019 5'9" 210002 1/4"NPS(F) Three- 240032 KB-4006 H-1921 Swivel Piece P-HC-4527 Reusable
6'3" 210007 3/8"NPS(F) Three- 240034 H-1975-1 Piece P-HC-4543 Reusable
Bulk Hose Chart Maximum Working Feet Type of Size Size Bulk Hose Pressure per Hose i.D. O.D. Model No. (PSi) Reel (Order No.)
Smooth 1/4" 1/2" H-1957 250 500 (210003) Cover 5/16" 5/8" H-1921 250 500 (210002) Air 3/8" 11/16" H-1958 250 500 (210004)
NylinerII 1/4" 1/2" H-1975-1 500 500 (210007) Fluid 3/8" 11/16" H-1973-1 500 500 (210006)
Premium Hose Helps Ensure Premium Paint Jobs
For properly piped shop information, see pages 78–79
HoseandFittings HoseandFittings 5756
(A)
(B)
(C)
(D)
Quick Disconnects – High Flow Ball and Ring Lock Type(For use with HVlP Spray Equipment)
Connection Order Thread Number Number Size
HC-4719 (A) 240147 1/4"NPT(M)
HC-4720(B) 240148 1/4"NPT(F)
Stem NumberHC-1166(C) 240015 1/4"NPT(M)
HC-4419*(D) 240145 1/4"NPS(F)
*Designedforsprayguns.Specialconeseatpreventsleaks!
Reusable ConnectionsHose Size and Type (M) Male Fits (F) Female Straight Connections Size Size DeVilbiss Connection Female Complete i.D. O.D. Hose No. Thread Size Connection No.
1/4" 1/2" H-1957 1/4"NPS(F) P-HC-4523 H-1975-1 3/8"NPS(F) P-HC-4543
5/16" 5/8" H-1921 1/4"NPS(F) P-HC-4527 1/4"NPS(M) P-HC-4599
3/8" 11/16" H-1973-1 3/8"NPS(F) P-HC-4548 H-1958 1/4"NPS(F) P-HC-4528 1/4"NPT(M) P-HC-4955
AdaptersPart Straight Type Number Male Thread Female Thread
AD-404 1/4"NPS 3/8"NPS
P-H-4105 3/8"NPS 1/4"NPS
Valves - Ball TypePart Number Thread
VA-540 3/8"NPS(M)x3/8"NPT(M)
VA-542 1/4"NPS(M)x1/4"NPT(M)
VA-595 1/2"NPT(M)x1/2"NPT(M)
Nipples (MBE) Male Both EndsPart Straight Type Number Male Thread Male Thread
AD-31 1/4"NPS 1/4"NPS
H-2008 1/4"NPS 1/4"NPT
H-1446 3/8"NPS 3/8"NPS
AD-11 3/8"NPS 3/8"NPT
CouplerPart Number Thread
SSP-69 1/4"x1/4"NPT(F)
Hose Fittings
The chart above shows test data at 25 SCFM using:
DeVilbiss high flow HC-4720 coupler, HC-4419 stem.RBL 611 coupler, 612 stem.Sharpe 8320 coupler, 8330 stem.Original DeVilbiss P-HC-4120 coupler, P-HC-201 stem.Milton/Sata “P" style 1804 coupler, 1810 stem.Milton “M" style S715 coupler, S727 stem.Sata/Milton “T" style 784 coupler, 786 stem.Milton “A" style S775 coupler, S777 stem.
DesignedtoOptimizeAirflowforTopSpray Gun and Air Tool Performance
Pressure Drop Comparison at 50 PSi inlet at 25 SCFM
HoseandFittings HoseandFittings 5958
Hose Fittings
240109P-HC-4482
Female Thread3/8"NPS
NPT= taperedNPS=straight(M)= Male(F)= FemaleWheneverpossible,matchstraightthreadswithstraightthreadsandtaperedwithtapered.Otherwise,leakagemayoccur.
240145HC-44191/4"NPS(F)
240015HC-1166
1/4"NPT(M)
Air Tools (Male Stem)
Spray Equipment (Female Stem)
Air Hose210004H-19583/8"I.D.
240156P-HC-4808-13/8"NPS(M)
240035P-HC-45483/8"NPS(F)
240148HC-47201/4"NPT(F)
240147HC-4719
1/4"NPT(M)
240037P-HC-45991/4"NPT(M)
Fluid Hose210006
H-1973-13/8"I.D.
240032P-HC-45271/4"NPS(F)
240033P-HC-45281/4"NPS(F)
Air Hose210002H-19215/16"I.D.
SpecialCone Seat
Prevents Leaks!
Digital Gauge with Air Adjusting valveOrder No. Model No.803291 HAV-555
Order No. Model No. 803289 DGi-101 Digital Gauge Only
Specifications:• Accuracyto+/-0.5PSI• UL/CSAapproved• Gaugerange:2.5to160PSI• Autooffafter60secondstopreservebatterylife• Upto4yearsofbatterylife,dependingonusage
High Output Air Adjusting valves and GaugesOrder No. Model No.180005 HAV-500
Order No. Model No.180006 HAV-501 w/Gauge
Order No. Model No.180089 HAV-511 w/Gauge
Order No. Model No.803236 HAV-512 w/Gauge
Gun Mounted Air Adjusting Valves and Gauges
Order no. model no.
max. inlet
Press.max. reg Press. PSi Air inlet Air Outlet
180005HAV-500
175 — 1/4"NPS(M) 1/4"NPS(F)(Swivel)
180006HAV-501 w/gauge
160 0–160 (GaugeRange)
1/4"NPS(M) 1/4"NPS(F)(Swivel)
180089 HAV-511 w/gauge
160 0–160 (GaugeRange)
1/4"NPS(M) 1/4"NPS(F)(Swivel)
803236HAV-512 w/gauge
100 100 1/4"NPS(M) 1/4"NPS(F)(Swivel)
803291HAV-555 Digital
160 2.5–160 1/4"NPS(M) 1/4"NPS(F)(Swivel)
HAV-511
HAV-501
HAV-512
HAV-500
HAV-555
AirRegulators/AirAdjustingValves 61HoseandFittings60
millennium 3000 respiratorsOrder No.900254Model No.40-141
Order No.900253Model No.40-128
Order No.900255Model No.40-143
CautionNotforusewithpaintsthatcontainisocyanates.Readandfollowallprintedwarnings.Aqualifiedsafetyexpertorhygienistshouldbeusedtoselectthecorrectrespirator.
Millennium 3000 RespiratorsOrder No. Replaceable Model No. Size Description cartridges
900253 Medium Millennium3000Respirator Yes 40-128
900254 Small Millennium3000Respirator Yes 40-141
900255 Large Millennium3000Respirator Yes 40-143
Approved,whenusedasspecified
ExtremelyComfortable,Strong and Durable with Sizes to Fit Most Painters and Technicians
Millennium 3000 Replacement PartsOrder No. Model No. Description900259 40-1921-10 Cartridge(2/Card,Kitof10Cards)900261 40-1924-10 Pre-filter(10/Card,Kitof10Cards)900262 40-1925 Cover(Kitof2)
Air RegulatorsOrder no./model no. Description130516 / 130516 75 CFM air regulator, gauge and valve
(regulatoravailableseparatelyas130521)130093 / HAR-600 60 CFM air regulator,gauge and valve
(regulatoravailableseparatelyasHAR-507)192242 / HAR-511 60 CFM air regulator
Flowthroughregulatorforpressuretanks130100 / HAR-520 50CFMairregulator—non-relieving
(purchaseGA-375gaugeseparately)
Air regulatorsOrder No.130516
Order No.130093Model No.HAR-600
Order No.192242Model No.HAR-511
Order No.130100Model No.HAR-520
HAR-600
HAR-511
HAR-520
130516
HARG-555Digital
HARG-510
Gun mounted regulators and GaugesOrder No. Model No.130015 HARG-510
Order No. Model No.802419 HARG-555 w/digital gauge
Gun Mounted Regulators and Gauges
Order no. model no.
max. inlet
Press.max. reg Press. PSi Air inlet Air Outlet
802419 HARG-555 Digital
160 2.5–100 1/4"NPS(M) 1/4"NPS(F)(Swivel)
130015HARG-510
175 100 1/4"NPS(M) 1/4"NPS(F)(Swivel)
Breathable Air 63AirRegulators/AirAdjustingValves62
Breathable Air HoseOrder No. Model No. Description
160015 MPV-530 30' Breathable air hose assembly160016 MPV-550 50' Breathable air hose assembly
Breathable Air Systems Belt No. of Regulator Breathable Visor Filtration Order No. and Hood Air Covers unit Filtration Model No Assembly Hose (30') included included Description
165013 Yes No 2 None — MPV-625
160019 Yes Yes 12 DAD-503 3-stage filtration MPV-651 withdesiccant air dryer systen
160020 Yes Yes 12 HAF-601 3-stage MPV-652 filtration system
160018 Yes Yes 12 DAD-504 Desiccant MPV-650 retrofit system
Breathable Air Filtration Removes Removes Removes Order No. dirt to liquid oil Removes Removes Model No. Description 5 micron water aerosols humidity odor
130089 3-stage filtration Yes Yes Yes Yes Yes DAD-503 withdesiccantair dryer system
130087 3-stage filtration HAF-601 system Yes Yes Yes No Yes
130096 Desiccantretrofit Yes,when Yes,when Yes,when Yes,when Yes DAD-504 system used with used with used with used with DAD-500 DAD-500 DAD-500 DAD-500 orHAF-518 orHAF-518 orHAF-518
Protect your Health with an Air Supplied Respirator and FiltrationmPv-625•Easilyaccommodatesprescription eyewearandbeardedemployees
•Adjustablebeltwithquickfitbuckle
•Vizorwindowimprovedtoreduceglare
• Coolandcomfortable
• MeetsNIOSHapproval(TC19C-0368)
• MeetsOSHARequirementsInletpressuresspecifications: Operatinginletpressures45–100PSInominalflowratetoVizor6.5CFM
Air vizor™
BrEAtHABLE Air SyStEmS
* AirVizor™requiresproperairlinefiltrationandcarbonmonoxide(CO)monitoringtocompleteanapprovedsuppliedairrespirator.Acarbonmonoxide(CO)monitormaybepurchasedlocallyorfromENMETCorp.(734)761-1270(phone).OrderformavailablefromDeVilbissuponrequest.
DAD-503
DAD-504
HAF-601
ALSO inCLuDES ½" BALL vALvE
SHutOFF FOr EASy mAintEnAnCE
Breathable Air Breathable Air 6564
Clean Solutionsn Dirt Control Floor Coat
nBumperPrepPad
n DeWIPE-OUTS
Devilbiss® Dirt Control Floor Coat
DeVilbiss® Dirt Control Floor CoatOrder No. Description
803491 DirtControlFloorCoat(5gals.)
803492 2-gallonPumpSprayer
Features/Benefits• Significantlyreducesbuffingtimecausedbydirt inpaintjobs
• Reducesairborneparticlesinasprayboothbytrappingthem to booth floor
• Canbeusedinconcretefloorpaintbooths,idealforshopssprayingwaterborne(notforusewithpaintedconcrete,tile,orgratedfloors)
• Water-based,reducesVOCexposure• Helpsreducestaticinpaintbooth,preventing paintcontamination
Clean Solutions 6766
Devilbiss® Bumper Prep Pad
DeVilbiss® Bumper Prep PadOrder No. Description
803557 All-In-OneBumperPrepPad(1perpkg.)
•Clean,abradeanddegrease in one easy step
•Reducesstepsin bumper prep process to increase efficiency
•Providescomprehensiveabrasion for better adhesion
improves paint job quality•“StaticKiller”formula dramaticallyreducesstatic chargeandstatic-relateddirt
•Greatforplasticparts andbumpercovers
•Removesresidue andfibersleft bytacking
Saves time•Reducesbuffing•Advancedtechnology fabricprovidesfast andconsistentdrying
large, lint-free wipe
OEM-preferred
The final step before painting*
DeWipe-Outs™ Prep WipesOrder No. Size Description Application
803045 11"x17" 85%IPA/15%DIWater Mostclimates
803046 11"x17" 50%IPA/50%DIWater Warmer/dryerclimates orheatedspraybooths
803418 11"x17" Acetoneblend,California VOCcompliant exempt.Mustbeusedwith Californiablend 803048storagecase
803048 Storagecasew/lidgasket &snapclosure
Pre-saturated Prep Wipe
*Useontwo-componentorwaterborneprimers
50 wipes per pouch
803418VOCcompliant
803045 and 803046
Resealable pouches
803048Storagecase
Clean Solutions Clean Solutions 6968
n includes: GunCases,SprayGunCleaningKits,CupLids, FluidStrainers,GunWrenches,SprayGunLube, WhirlwindAirFilters,PaintStrainers,etc.
Maintenance& Accessories
Order No.192212
Professional Spray Gun Cleaning Kit
Gravity Spray Gun Cup LidsGravity Gun Cup Lids190944 Disposable lid Kit GFC-404-K2 forGFC-502gravity cup(Kitof2)190225 lid Assembly Kit GFC-402 forGFC-501 gravitycup
GFC-404-K2
GFC-402
Paint Strainers
Paint StrainersOrder No. Pkg Model No. Description Qty.
901441 Fine Mesh 5 81-82 (145)White
901442 Medium Mesh 5 81-83 (100)Blue
901443 Coarse Mesh 5 81-84 (80)Red
Spray Gun LubeSpray Gun lube181001 SprayGunLube SSl-10 • Containsnosiliconeor
petroleumdistillates• Compatiblewithallpaint
materials• 2oz.bottle
Scrubs® Hand cleaner towelSOrder No.192218 Bucket of 72 Scrubs
Pre-moistened, heavy-duty towels easily remove soil from your hands.• Portableandconvenient.
• Conditionsandsoftens.
• Useontools,equipment andworksurfaces.
• Worksfastondirt,oils,adhesives,lubricants,paints,grease,tar,urethanes, epoxies,inksanddyes,sealantsandcaulks.
For automotive collision repair
technicians
Maintenance/Accessories 7170
149-278
Gun WrenchesGun WrenchesOrder No. Model No. Description
702740 702740 10mmand14mmwrench,forusewithallTEKNA® and DeVilbiss SRi Pro guns
180008 WR-103 For use with DeVilbiss FLG, GTI, JGA, and PLUS guns as well as many other brands
900712 54-3918 ForusewithM1-GandMach1HVLPsprayguns
900431 5-476 Forusewith2001spraygun(notshown)
802531 SPN-5-K ForusewithallDeVilbisssprayguns(exceptSRiPro) andworkswithmanyotherbrands(notshown)
54-3918
WR-103
702740
Fluid Strainers
VS-532PLH-MF-6-100 KGP-5-K5
Strainers Max. Order No. Working Model No. Application Description Pressure
190181 GravityCup FluidStrainer N/A KGP-5-K5 900006 SuctionCupTube Strainer N/A 149-278240129 Pressure Gun Fluid Strainer 250 PSI PlH-MF-6-100 180073 Pressure Gun Fluid Strainer 300 PSI VS-532 191925 ReplacementScreen Screen-100Mesh N/A VS-58-K10 for VS-532 240131 ReplacementScreen Screen-100Mesh N/A PlH-MFC-100 for PLH-MF-6-100
model 140-B Engine/Part Cleaning GunOrder No. Model No.901205 6530-0000-1
Extensiongunforcleaningenginesand automotive equipment
includes: 6' hose
Clean. Fast. Efficient.Premium Paint Strainers• Singlemeshedtip–eliminatesunstrainedpaintpassingthroughthetip• Fastandstrong• Lintfreenylonstrainers• Consistentmeshsizesforoptimumfiltration
DeKones™ Premium Paint StrainersOrder No. Model No. Description
802352 Nylon-Medium,226micron,100/box802394 Nylon-Medium,226micron,250/bag,1000/case802351 Nylon-Fine,190micron,100/box802353 Nylon-Fine,190micron,250/bag,1000/case803253 Nylon-Superfine,125micron,100/box802852 Nylon-Superfine,125micron,250/bag,1000/case
Gun Storage Cases
Order No. Model No.192246 BXX-1250
Order No. Model No.802136 BXX-1258
SinGLE Gun CASE
tWO-Gun CASE
Two-gun case holds:Any2fullsizeDeVilbiss®gravitysprayguns–or–Any1fullsizeDeVilbiss® gravityspraygunandtheDeVilbissSRiPro™spotrepairgravityspraygun,2aluminumgravitycups–or–1aluminumgravitycup,andthealuminum4fl.oz.gravitycupandtheplastic4fl.oz.gravitycup,4fluidtips,1DeVilbiss®highoutputgunregulatorwithgauge,2gunhooks,1guncleaningkit
Single gun case holds:Any1fullsizeDeVilbiss®gravityspraygunandaluminumcup,5fluidtips,1DeVilbiss®highoutputgunregulatorwithgauge,1guncleaningkit
WaterborneCompatible
Store your guns and their accessories—
fits all DeVilbiss gravity spray guns
Maintenance/Accessories Maintenance/Accessories 7372
Whirlwind™ DiSPOSABLE Air FiLtEr
CanbeusedwithallHVLPsprayguns
Whirlwind: longer life and less pressure drop
Whirlwind Disposable Air FilterOrder No. Model No. Description130028 Whirlwind Filter HAF-507 130095 Whirlwind Filter HAF-507-K2 2pack
DeVilbiss
Motor Guard
Sharpe
Viskon- Aire
Patented two-stage filter Stage 1- Swirl Chamber
Removeslargewaterdroplets
Stage 2- Filter Media Removes smaller water droplets,oildroplets,and dirtparticles
All other competitive filters:• Waterdropletssaturatethe
filtermedia—shortening thelifeofthefilter
• Smallerinletsurfacearea increasespressuredrop
Cross-sectionviewoffilters
6
5
4
3
2
1
0DeVilbiss Motor Guard Sharpe Viskon-Aire
FILTER ELEMENT INLET SURFACE AREALarger area = longer life & less pressure drop
DeVilbiss has largest surface area
Surf
ace
Area
(squ
are
inch
es) 7
6
5
4
3
2
1
0DeVilbiss Motor Guard Sharpe Viskon-Aire
FILTER PRESSURE DROPLower drop = better flow
DeVilbiss has lowest pressure drop
PSI P
ress
ure
Dro
p(@
80p
si w
ith 2
0 cf
m fl
ow ra
te)
FILTER TOUGHNESSEnergy needed to break male thread. More energy = stronger.
DeVilbiss bends, but doesn’t break120
100
80
60
40
20
0Ener
gy N
eede
d to
Bre
ak F
ilter
(inch
-pou
nds)
DeVilbissThread did NOT BREAK
at 108 in.-lbs.input energy
Motor GuardThread brokeat 25 in.-lbs.
i nput energy
SharpeThread brokeat 25 in.-lbs.input energy
Viskon-AireThread brokeat 25 in.-lbs.input energy
Maintenance/Accessories Maintenance/Accessories 7574
Order No.802182Model No.DAD-600-1
Order No.130504
DAD-600-1DAD-500 DESiCCAnt tunE-uP Kit
Ct DESiCCAnt CArtriDGE DryEr
Desiccant Charge & TS-10 Tune-up Kit Order No. Model No. Description
130506 DC10 10lbs.desiccantcharge
130508 TuK10 TS-10tune-upkit(10lbs.desiccantcharge, humidityindicator,coalescingfilter)
Desiccant Tune-up KitOrder No. Model No. Description
802182 DAD-600-1 Desiccantrefill,1stand2ndstagefilterelements130030 DAD-600 Desiccantrefill,1ststagefilterelement190831 DAD-1 Desiccantrefill
Order No.130506Model No.DC10
Desiccant Charge (10lbs.)
Keep your TS-10 and Other Desiccant Systems Performing like New!
Order No.130508Model No.TuK10
tS-10 tune-up Kit
includes:•Desiccantrefill(DAD-1)•Filterelementkit(HAF-6)•Coalescingfilterelement(HAF-28)
A Well-Maintained DAD-500 Helps Eliminate Paint Defects
High Holding Capacity for All Dry Spray Booths
Flame retardant Booth Paper
Order No.900115Model No.29-836
Highly AbsorbentSuitableforfloor,walland equipmentcoverwhilespraying
AF Filters™ Exhaust Air Filters
Order No.900113Model No.29-356
Size: 3' x 30' 90sq.ft.ofsurfacearea 8pleatsperft.
Size: 60"x300'
Average Removal
Efficiency: 98.1%
Maintenance/Accessories Maintenance/Accessories 7776
Refrigerated
Dryer
Compressor
Slope Line
GENERAL PURPOSE
AIR TOOLS
mumini
M teeF 02
Slope Line
PREP AREA
SPRAY BOOTH
MainLineFilter
HAR-602 #130099
35 ft. 3/8" Air Hose with High Flow FittingHA-5867 #220052
HeatResistantFlex Hose
#130522CT Plus 5-Stage Filter/Desiccant Dryer
LOWEST POINT
Auto Drain# 130512
35 ft. 3/8" Air Hose with High Flow FittingHA-5867 #220052#130522
CT Plus 5-StageFilter/Desiccant Dryer
Water and Particulate Filter/Regulator
HAR-602 #130099
Water and Particulate Filter/Regulator
Auto Drain# 130512
A Properly Piped Shop is of Prime importance for a Premium Finish.Onthesurfaceitmaynotseemlikeasignificantfactorinturningoutaqualitypaintjob,buttheplumbingofyourshop'sairlinesisveryimportant.Correctinstallationisnecessaryforoptimumperformanceofyourequipment.
Correctairlinepipingissoimportantbecauseitcanreducecontaminantsinyourairsupplybyupto75percent.Reducingcontaminantstothefilteralsoreducesthefrequencyoffilterreplacement,maintenance,andmostimportantly,reducesthe riskofcontaminantsinyourpaintjob.
Thefollowingchartanddiagramwillhelpyoureducepressuredropinyourairlinesandhelpreducecontaminationinyour paintjob.
Minimum Pipe Size Recommendations for Header or Main Air LinesCompressor Compressor Main Min.Pipe Size (HP) Capacity (CFM) Air line Diameter
5–10 15–40 Upto200ft. 1in. Upto1000ft. 1¼in.
15–20 45–80 Upto200ft. 1¼in. Upto1000ft. 1½in.
25–30 75–120 Upto200ft. 1½in. Upto1000ft. 2in.
Minimum Pipe Size Recommendations for Drop LegsHighest CFM Tool being used Min. Pipe on this Drop leg Drop leg Diameter
Upto20CFM Upto50ft. ½in.
Over20CFM Over50ft. ¾in.
Guidelines to Piping your Shop• Alwaysuseflexhosefromcompressortopiping• Allow20'minimumbetweencompressorand refrigerantdryer
• Runheaderpipeinafullloop• Eliminateunnecessaryteesandelbows• Takedropsfromthetopoftheheaderpipe• Dropsshouldbeascloseaspossibletothepoint ofapplication
• Slopethepipingtoaccessibledrainpoints
ProperlyPipedShop ProperlyPipedShop 7978