9176025 - biospray

Kills 99.999% of Bacteria & Viruses

Save 55-63% on Labor Costs

Use 60-88% Less Product

Non-Flammable, Non-Corrosive & No Rinse

Hospital-Grade Disinfectant Sanitizer for Food Contact Surfaces

1

1

Sanitizing & Disinfecting System

BioSpray  D2™  is  U.S.  Environmental  Protection Agency registered and approved as a tuberculocide, virucide,  disinfectant  &  surface sanitizer  and  meets Regulatory Standards (CFR 178.1010) approved as a no  rinse  sanitizer/disinfectant  for  food  contact surfaces 

BioSpray Power Pack™ Models PSD-5 Backpack, PSD-10 & PSD-20 comply with the applicable requirements imposed by the U.S. Food and Drug Administration

BioSpray D2™ meets U.S. Department of Agriculture Pre-NSF era standards for the D2 no-rinse rating and is Federal Insecticide, Fungicide and Rodenticide Act registered and certi�ed for general use

BioSpray  D2™  is  National  Sanitation  Foundation registered  and  certi�ed  for  contact  with  food surfaces  with  no  rinse or  wipe down  required and meets regulatory requirements of FDA 21 CFR  

BioSpray D2™  is Kosher/Pareve certi�ed to contain no animal or dairy ingredients

BioSpray Sanitizing & Disinfecting Systems™ are eligible for Veterans First Contracting Program with U.S. Department of Veteran A�airs through certi�ed Service-Disabled Veteran-Owned Small Business (SDVOSB) partnership

The BioSpray™ Sanitizing & Disinfecting Systems sanitize and disinfect faster and more completely than conventional spray methods, reducing labor costs 55-63% while using 60-88% less product1. The BioSpray™ system includes the:

BioSpray Power Pack™ PSD-20, PSD-10 and PSD-5 Backpack Models BioSpray D2™ Surface Sanitizer & Disinfectant Chemical Solutions

The BioSpray Power Packs™ utilize a regulated CO2 delivery design to propel the BioSpray D2 faster, more e�ciently and more conveniently than ever before. Systems using CO2 to deliver sanitizing solutions were developed in the early 1990’s in the Paci�c Rim and required the use of electric heaters to keep the CO2 propellant from freezing with continuous use. As a result, convenience was sacri�ced because these �rst generation units had to be tethered to AC outlets via power cords, and as with many early technologies, they were big, heavy, bulky and expensive.

BioSpray Power Pack™ PSD models are the �rst completely portable, non-electric, no external heater, no freeze2 CO2-powered technology systems to spray a sanitizing solution to be created, designed, manufactured and marketed in the U.S.A.

BioSpray Power Pack™ PSD models are made from lightweight aircraft aluminum, are a�ordable and have no cords to cause safety concerns and no electrical current, making them safe for use in virtually all environments. The PSD-5 Backpack model is built on an ALICE military frame providing even more �exibility for sanitizing hard to reach locations, and on every PSD model, the system regulator can quickly and easily adjust to provide the necessary pounds per square inch needed to utilize the 50 and 100 foot coil hoses.

BioSpray D2™ Surface Sanitizer & Disinfectant is a propri-etary blend of isopropyl alcohol and quaternary ammo-nium solution with proven hospital-grade disinfecting killing power that is non-corrosive, non-staining and non-toxic, and is set apart from other solutions because even though it matches strength with the harshest chemicals, it is certi�ed safe to be applied directly on food contact surfaces without requiring a rinse; an extremely unique distinction. And because BioSpray D2™ is non-corrosive, it can be sprayed directly electronics, precision equipment, health care devices, keyboards, and other water-sensitive devices, including food service equipment and control panels, and there is no risk of cross contamination on any surfaces as no wiping is required to activate or remove the product; it quickly evaporates with no residual.

Alcohol-based chemical solutions were once widely used as disinfectants and sanitizers and the Centers for Disease Control (CDC) still lists isopropyl alcohol as an e�ective disinfectant for homes and hospitals. However, many industry segments dramatically reduced the use of alcohol-based chemical solutions because of �ammability, prompting the use of alternative chemicals with more favorable �re-safe ratings but that commonly include undesirable traits such as corrosiveness, toxicity, e�cacy, long dwell times, resistance buildup and/or speed of application, among others.

In addition to providing the propellant power for the BioSpray D2™ solution, the BioSpray Power Pack™ PSD models utilize the CO2 to serve a second critical function: �re retardant. The PSD model’s technology aerosolizes the BioSpray D2™ encasing the oxygen molecules with the carbon dioxide, rendering the alcohol-based BioSpray D2™ completely non-�ammable without diminishing the e�ectiveness of BioSpray D2’s™ proprietary alcohol-quat blend, making it safe to use an alcohol-based solution once again as a disinfectant and surface sanitizer.

1Compared to manual hand-pump spraying; see MicroBioTest, Inc. independent laboratory testing validation reports and ROI/Cost Bene�t Analysis for full details.

2The BioSpray™ patent-pending technology allows the contents of the system’s CO2 drive cylinder to be continuously sprayed until empty without the contents freezing and thus stopping the operation; when the system’s CO2 drive cylinder is completely emptied from continuous spraying from start to �nish, a variable recovery period (based on the PSD model) of up to ninety minutes may be needed to allow for the system to provide another complete emptying of the drive cylinder when continuously sprayed. Ask for a ROI/Cost Bene�t Analysis to determine the type and number of PSD systems, as well as the Recovery Period discount when multiple systems are required due to area and continuous spraying requirements.

Patent-Pending TechnologyNo Electricity, Fire-Safe, Non-Corrosive Spray Portable, Light Weight Aircraft Aluminum Design

BioSpray Power Pack™ Models

PSD-10PSD-5

Backpack

PSD-20

BioSpray™ Sanitizing & Disinfecting SystemA Better Solution™

Traditional hand sprayer bottles and manual spray-pump systems cannot atomize the disinfectant properly or provide even coverage which leads to wasted formula, increased chemical costs and labor time and worst of all, potentially unprotected areas.

Products that are safe for the environment and humans generally end up costing companies more than other solutions that are not environmentally friendly. The BioSpray™ Systems are not only non-corrosive and non-toxic, they are far less expensive overall than conven-tional, caustic sanitizing and disinfecting solution alternatives, and in most cases they pay for themselves in a matter of months.

Our latest, environmentally e�cient atomizing spray guns ensure the least amount of formula while maintaining e�cacy and the fastest application time on the market, saving employee hours and dramatically lowering solution usage.

BioSpray Power Pack™ is the �rst CO2-based propellant system to validate through an independent laboratory, the proof-of-e�cacy of the sanitizing and disinfecting solution after it’s been atomized, as well as the �rst to validate by independent lab, the certi�ed speed of application and amount of solution used.

The �nancial bene�ts and substantial savings of the BioSpray™ system are provided in a comprehensive Return On Investment (ROI)/Cost Bene�t Analysis that includes and compares all expenses including labor, type and number of PSD systems, formula and accessories.

MicroBioTest, Inc. Independent Laboratory Tested and Certi�ed

Speed, Chemical Usuage & Proof-of-E�cacy Validation

Easy OperationSpray Up to 15 FeetQuick Adjust up to 120 psi.

Added Convenience

BioSpray D2™ does not require dilution or mixing and is provided in convenient, ready-to-use one liter bottles sold in case lots of 12 that can be air shipped overnight delivery for emergency situations.

Limited Lifetime Warranty

The BioSpray Power Pack’s™ have a free Lifetime Limited Warranty that includes 5-year recerti�cation of the system when minimum requirements are met*.*Certain conditions apply; ask for complete details.

A Better Solution™

BioSpray™ Sanitizing & Disinfecting System

Kills 99.999% of detectable pathogens

Saves 55-63% of labor costs

Reduces chemical usage by 60-88%

Pays for itself in months

Low dwell times

Fire-safe

Non-corrosive

Non-toxic

No rinse

Model PSD-20

BIOSPRAY D2™ TECHNICAL SPECIFICATIONSE.P.A. Reg. No. 73232-1-86168

ACTIVE INGREDIENTS:Isopropyl Alcohol......................................................58.6000%Octyl Decyl Dimethyl Ammonium Chloride......0.0075%Didecyl Dimethyl Ammonium Chloride..............0.0045%Dioctyl Dimethyl Ammonium Chloride...............0.0030%OTHER INGREDIENTS................................................41.3850%

Warning: Flammable in Bottle; Non-Flammable whenapplied through BioSpray Power Pack™

Color: Clear Liquid

Kilograms per Liter: 0.8

Quick and Convenient

Ready-to-Use

Evaporates Quickly

Non-Corrosive

For Food Contact Surfaces Without Rinse

60 Second Contact Time for Sanitizing; 5 Minutes to Disinfect

INDEPENDENT ANTIMICROBIAL EFFICACY TESTING PERFORMED BY MICROBIOTEST, INC. & COMPLIANCE CERTIFIED WITH GOOD LABORATORY PRACTICE REGULATIONS:

Backpack Model PSD-5

U.S. Environmental Protection Agency (EPA)  Registration Number 73232-1-86168

NSF International - National Sanitation Foundation (NSF)  Registration Number 126509 

FOOD CONTACT SANITIZER TESTS – 1 MINUTE DWELL  Staphylococcus aureus (ATCC 6538)  Escherichia coli (ATCC 11299)  Escherichia coli O157:H7 (ATCC 43895)  Pseudomonas aeruginosa (ATCC 15442)  Salmonella typhimurium (ATCC 13311)  Listeria monocytogenes (ATCC 19111)  Enterobacter sakazakii (ATCC 51329)  Vibrio cholerae (ATCC 14035) 

AOAC TUBERCULOCIDAL TEST – 5 MINUTE DWELL  Mycobacterium bovis, BCG 

AOAC GERMICIDAL HEALTH CARE TESTS – 5 MINUTE DWELL  Staphylococcus aureus (ATCC 6538)  Pseudomonas aeruginosa (ATCC 15442)  Salmonella choleraesuis (ATCC 10708)  Staphylococcus aureus MRSA (ATCC 33591)  Enterococcus faecium VRE (ATCC 51559)  Escherichia coli O157:H7 (ATCC 43895)  Listeria monocytogenes (ATCC 19111)    AOAC FUNGICIAL TEST – 5 MINUTE DWELL  Trichophyton mentagrophytes (ATCC 9533)    VIRUCIDAL TESTS – 5 MINUTE DWELL  Norwalk virus [FCV]  Hepatitis B virus [HBV]  HIV virus (HIV-1)  Avian In�uenza virus Swine In�uenza virus (H1N1)

Generally speaking, disinfectants can be placed into categories based on the speci�c active ingredient (the chemical or combination of chemicals in the product that actually kill the target microorganisms) they contain.

All disinfectants have varying degrees of e�cacy and speed of kill, and may also carry drawbacks ranging from the need to mix or a mild odor to staining, extreme toxicity, or loss of e�cacy under imperfect conditions. Following is a summary of the most common categories of commercial disinfectants:

Glutaraldehyde-Based Products are generally cheap and are not known to stain or corrode surfaces that they are applied to. Their disadvantages lie in their need to be mixed, the foul odor they produce, their toxicity, and their need for contact times up to 20 minutes. These products are more speci�cally meant to be used as cold sterilants, not as hard-surface disinfectants.

Phenol-Based Products generally don't have much of an odor and do not stain or corrode the surfaces that they are applied to, and have the increased bene�t of low price when concentrated formulas are purchased. Where these products lose points is in the fact that they are not very fast-acting (typically 10 minutes), a residue will eventually build-up on the surfaces, and they are found to be extremely toxic, often causing sinus and respiratory problems, as well as headaches and nausea due to overexposure and lack of proper ventilation.

Iodophore-Based Products are generally low odor, non-corrosive, and inexpensive, but they lack speed of kill and their dilution and contact times are far too critical for their e�cacy to be consistent and practical in most settings.

Bleach-Based Products are well-known for their killing power, speed, and safety, but they tend to be extremely corrosive and damaging to surfaces and usually contain a heavy odor. They are not typically recommended for use on most surfaces.

Quaternary Amonium-Based Products are the commonly used type of hard-surface disinfect and they have been found to be very e�ective and safe. However, quat drawbacks include the speed of kill (also typically 10 minutes), the potential for staining and residue to be left behind, depending on the amount of quat found in the particular product’s formulation. The higher the level of quat, the more it will lead to staining.

Alcohol/Quat-Based Products are becoming widely accepted to be the safest and fastest disinfectant products on the market today. They also kill a wide range of pathogens and don't typically contain any staining or corrosive characteristics. They are fairly cheap, especially for a ready-to-use product, and don't present any serious health hazards. They do tend to contain an odor although it usually dissipates rather quickly.

Least susceptible

Most susceptible

BACTERIA WITH SPORES(Bacillus subtilis, Clostridium tetani, C. di�cile, C. botulinum)

PROTOZOA WITH CYSTS(Gardia lamblia, Cryptosporidium parvum)

MYCOBACTERIA(Mycobacterium tuberculosis, M. avium-

intracellulare, M. chelonae)

NON-ENVELOPED VIRUSES(Coxsackieviruses, polioviruses, rhinoviruses, rotaviruses,

Norwalk virus, hepatitis A virus)

FUNGI(Candida species, Cryptococcus species, Aspergillus species, Dermatophytes)

VEGETATIVE BACTERIA(Staphylococcus aureus, Salmonella typhi, Pseudomonas aeruginosa, coliforms)

ENVELOPED VIRUSES(Herpes simplex, varicella-zoster virus, cytomegalovirus, Epstein-Barr virus, measles virus, mumps virus, rubella virus, in�uenza virus, respiratory syncytial virus, hepatitus B and C viruses, hantaviruses, human

immunode�ciency virus, and H1N1 in�uenza virus)

REFERENCE GUIDE TO DISINFECTANTS*

MICROORGANISMS SUSCEPTIBILITY OF CHEMICAL DISINFECTANTS

Hospital-G

rade Disinfection

BioSpray D2™is Hospital-Grade. Kills of

Detectable Pathogens

Concentrate = requires dilution with water prior to use.RTU = ready to use.

Non-Staining

Good

Good

Good

Poor

Good

Good

Excellent

Non-Corrosive

Good

Good

Good

Excellent

Poor

Excellent

Excellent

Speed

Poor

Poor

Poor

Poor

Excellent

Poor

Excellent

Non-Toxic

Extremely Poor

Extremely Poor

Extremely Poor

Good

Good

Excellent

Excellent

Odor

Poor

Good

Good

Good

Extremely Poor

Excellent

Good

Convenience

Good

Poor

Excellent

Poor

Excellent

Excellent

Excellent

Price

Good

Excellent

Good

Excellent

Good

Good

Good

*Source: Dental Explorations, LLC; Balancing the Art, Science, and Business of Dentistry Hard-surface disinfectants by Je�rey C. Hoos D.M.D., F.A.G.D.

Disinfectant

Glutaraldehyde(concentrate)

Phenol(concentrate)

Phenol(RTU)

Iodophore(concentrate)

Bleach(RTU)

Quaternary Ammonium(RTU)

Alcohol/Quat(RTU)

99.999%

Same hospital-grade disinfectant that kills 99.999% of all detectable pathogens in a safe, non-�ammable aerosol can! Perfect for smaller, fast, no-wipe, no-rinse surface sanitizing & disinfecting jobs in:

School Rooms • Buses • Cruise Cabins • Airplanes • Emergency ResponsePolice Cars • Ambulances • Single Hospital Rooms • Single Correction CellsRestaurants • Office Cubicles • Keyboards • Electronics • Public Bathrooms Elevators & more

Ask to be added to our Notice List and we’ll send you an email when BioSpray D2™ Aerosol is released.

1PBPSD5 BioSpray Power Pack™ Model PSD-5 Backpack 5 lb. CO2 Power Driver

1PBPSD10 BioSpray Power Pack™ Model PSD-10 10 lb. CO2 Power Driver

1PBPSD20 BioSpray Power Pack™ Model PSD-20 20 lb. CO2 Power Driver

1PBBSD2 BioSpray D2™ - 12 x 1 Liter (Case)

1PBBSD25 BioSpray D2™ - 5 Gallon Pail

1PBBSD250 BioSpray D2™ - 50 Gallon Drum

1PBCH20 Coil Hose - 20 Foot

1PBCH50 Coil Hose - 50 Foot

1PBCH100 Coil Hose - 100 Foot

1PBBSBH BioSpray D2™ Bottle Holder (All PSD Models)

1PBCO2R BioSpray™ Re-Filler Kit (All PSD Models)

1PBSC5 PSD-5 Backpack Travel Case

1PBSC10 PSD-10 Travel Case

1PBSC20 PSD-20 Travel Case

www.go1bio.com

Manufacturer  1 Priority Biocidal, LLC  2410 Gravel Drive  Fort Worth, Texas 76118 

(817) 590-8100 O�ce (817) 288-0686 Fax  [email protected]

For more information on BioSpray Power Pack™ systems & accessories or BioSpray D2™ 

Aerosol SprayComing Soon

CONFIGURATIONS & ACCESSORIES

Copyright 2009. All Rights Reserved.1 Priority Biocidal, LLC. Revision 2.0

Sanitizing & Disinfecting System

*PSD unit & rental supply cylinder not included

BioSpray™ Re-Filler KitIncludes Pump, Scale w/Digital Display & PSD Adaptor, Drive Cylinder, 2 Regulators & all hoses necessary*

Page 1 of 2

MATERIAL SAFETY DATA SHEET

1. PRODUCT IDENTIFICATION: BIOSPRAY D2 Chemical Family: Isopropyl alcohol-glycerol-water blend Manufactured For: 1 Priority Biocidal, LLC

2561 Gravel Drive Fort Worth, Texas 76118

Emergency Information: For chemical emergency (spill, leak, fire, explosion or accident), call CHEMTREC 24-hour emergency number 800-424-9300; International +1 703-527-3887 (collect calls accepted) or 1 Priority Biocidal, LLC 817-590-8100 between 8:30am & 4:30pm Central Time.

Other Information: EPA Registration Number 73232-1-86168 Precautions: Flammable. Keep away from high heat, sparks, flame and all other ignition sources. May be harmful or fatal if swallowed. Use with adequate ventilation. Avoid prolonged breathing of vapor. Avoid contact with eyes or mucous membranes where prolonged contact causes irritation.

Date Revised: March 1, 2005

2. HAZARDOUS INGREDIENTS Exposure Limits In Air (ppm) Chemical Names CAS Numbers Percent* ACGIH TLV OSHA PEL Other (specify) Isopropyl Alcohol 67-63-0 55-65% 400ppm 400ppm 500ppmSTEL Other non-hazardous ingredients 35-45% N/A N/A TOTAL 100.00 *Not a required category

3. PHYSICAL PROPERTIES

Vapor Density: 2.07 Physical State: Clear liquid Vapor Pressure: 33mm Hg @20°C Color: Clear Specific Gravity: 0.8857 Odor Alcohol odor Melting Point: NA Miscibility: 100% in water Boiling Point 180°F Stability: >5 years Viscosity: non-viscous Corrosion: non-corrosive Does not stain skin, fabrics, plastics, metals, glass, Formica. How To Detect This Substance: Mild alcoholic odor

4. FIRE AND EXPLOSION

Flash point: 21.49°C (tag closed cup) Auto-ignition temperature: >685 F. Flammable limits in air, volume %: lower 2; upper 12. NFPA Rating: Health (1), Flammability (3), Physical Hazard/ Instability (0)

FIRE FIGHTING PROCEDURES: Use dry chemical, "alcohol foam", or carbon dioxide. Water may be ineffective, but water should be used to keep fire-exposed containers cool. If a leak or spill has not ignited, use water spray to disperse the vapors and to protect persons attempting to stop a leak. Water may be used to flush and dilute spills to nonflammable mixtures.

5. HEALTH HAZARD INFORMATION

SYMPTOMS OF OVEREXPOSURE for each potential route of exposure:

INHALATION: Exposure to over 400ppm may cause headache, drowsiness, lassitude, loss of appetite and inability to concentrate. May cause irritation of the throat.

SWALLOWED: Can cause depression of central nervous system, nausea, vomiting, and diarrhea.

EYE CONTACT: Can cause eye irritation (stinging sensation) and tear production. Redness of conjunctiva may occur.

SKIN CONTACT: Causes no skin irritation if used as directed. Excessive, continuous exposure for a long period of time may cause defatting or drying of skin. Rate of absorption of active ingredients through skin or the effects thereof are unknown.

Page 2 of 2

INGESTION: Can cause depression of central nervous system, nausea, vomiting, and diarrhea. HEALTH EFFECTS FROM EXPOSURE ACUTE/CHRONIC: No special acute or chronic effects or risks are expected from usage as directed on label. Brief contact with eyes, conjunctiva or other mucous membranes may cause temporary irritation. Ingestion will cause irritation of throat and esophagus and may cause mental or physical disabilities associated with alcohol intoxication. FIRST AID, EMERGENCY PROCEDURES EYE CONTACT: Immediately flush affected area with plenty of cool water for at least 15 minutes. GET MEDICAL ATTENTION IMMEDIATELY. INHALATION: Immediately remove victim to fresh air. If victim has stopped breathing, give artificial respiration, preferably mouth-to mouth. GET MEDICAL ATTENTION IMMEDIATELY. INGESTION: If victim is conscious and able to swallow, have victim drink water or milk to dilute. Never give victim anything by mouth if victim is unconscious or having convulsions. CALL PHYSICIAN OR POISON CONTROL CENTER IMMEDIATELY. Induce vomiting only if advised by physician or poison control center. SUSPECTED CANCER AGENT? No. This product’s ingredients are not found in Federal OSHA, NTP or IARC lists. MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: None known when used as directed.

6. REACTIVITY DATA

STABILITY: Stable at room temperature for at least 5 years in a tightly closed container. CONDITIONS AND MATERIALS TO AVOID: Contact with acetyl chloride and a wide range of strong oxidizing agents which may react violently. HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide can form upon incomplete combustion. HAZARDOUS POLYMERZATION: None likely.

7. SPILL, LEAK AND DISPOSAL PROCEDURES ENVIROMENTAL PRECAUTIONS: Avoid uncontrolled releases of this material. Where spills are possible, a comprehensive spill response plan should be developed and implemented. SPILL OR LEAK PROCEDURES: In case of large spills, wear appropriate respiratory protection. Eliminate possible ignition sources. Contain spilled material. Transfer to secure containers. Where necessary, collect spilled product using absorbent media. Dilute spill with water and directly flow to any available sanitary drain. In the event of an uncontrolled release of this product, the user should determine if the release is reportable under applicable laws and regulations. WASTE DISPOSAL: All recovered product may be dispensed along with large volumes of water through normal sanitary sewage systems in gradual releases. Note: Dispose of all wastes in accordance with federal, state and local regulations.

8. SPECIAL HANDLING INFORMATION

VENTILATION: Adequate ventilation should be available for all uses of this product RESPIRATORY PROTECTION: Where exposure is likely to exceed acceptable criteria, use NIOSH/MSHA approved respiratory protection equipment. For normal use of product as a surface disinfectant, no respirators are deemed necessary. EYE PROTECTION: Contact of product with the eyes is not expected or anticipated in the normal use, However; if there is a possibility of splashing or other means of contact with eyes, chemical safety goggles meeting the specifications of ANSI Standard Z87.1 should be worn.

GLOVES OR OTHER PROTECTIVE CLOTHING: No protective gloves or clothing are deemed necessary for normal application of product STORAGE: Store product in cool place away from areas of high heat, flames or potential sparks. Empty containers may be discarded in trash after rinsing with water. SHIPPING DESCRIPTION: ISOPROPYL ALCOHOL, 3, UN1219, PGII.

For bottles one liter or less ORM-D in U.S.A.