MOTORCYCLE CARRIER MANUAL ASSEMBLY INSTRUCTIONS STEP 1. Place two tire cradles on L type junction plate. Attach with small bolts & nuts (See FIG.1 ) FIG. 1 STEP 2. Place 2” receiver bar inside support channel on underside of the L junction plate, aligning holes and using the long bolts. Attach bridge supports as shown using lock nuts; Attach medium bolts in two side of bridge supports respectively, getting through ramp support and the hole of two side for bridge support using locking nut. (See FIG.2) FIG. 2 TIRE CRADLE SMALL BOLTS & NUTS SUPPORT CHANNEL RAMP SUPPORTS BRIDGE SUPPORTS MEDIUM BOLTS & NUTS L JUNCTION PLATE 2” RECEIVER BAR LONG BOLTS ROTATION & ENLARGEMENT PICTURE SECTIONAL ENLARGEMENT PICTURE
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
MOTORCYCLE CARRIER MANUAL ASSEMBLY INSTRUCTIONS
STEP 1. Place two tire cradles on L type junction plate. Attach with small bolts & nuts (See FIG.1)
FIG. 1 STEP 2. Place 2” receiver bar inside support channel on underside of the L junction plate, aligning holes and using
the long bolts. Attach bridge supports as shown using lock nuts; Attach medium bolts in two side of bridge supports respectively, getting through ramp support and the hole of two side for bridge support using locking nut. (See FIG.2)
FIG. 2
TIRE CRADLE
SMALL BOLTS & NUTS
SUPPORT CHANNEL
RAMP SUPPORTS
BRIDGE SUPPORTS
MEDIUM BOLTS & NUTS
L JUNCTION PLATE
2” RECEIVER BAR
LONG BOLTS
ROTATION & ENLARGEMENT
PICTURE
SECTIONAL
ENLARGEMENT PICTURE
STEP 3. Adjusting Step 1 and Step 2 to the level position, screw on all lock nuts tightly
STEP 4. The carrier is designed to load the motorcycle from the left or right side using the ramp. There are 3 sets of center holes and 1 set of upper holes on each cradle. The large safety pins and clevis pins are used in the upper holes. See FIG. 4. The 4 large bolts are used in the center hole to support the motorcycle tires. NOTE:Depending on the size of your motorcycle some bolts may not be needed. (see FIG.3)
FIG. 3 STEP 5.The front tire of the motorcycle must rest down into the cradle and be secured with a large safety pin and clevis
pin. This step is needed in case a strap is broken or comes loose during transport. A second safety pin is supplied. Depending on the size of your motorcycle, this pin may not be needed. If this pin is not used, secure the motorcycle tire with a strap. (Not included – We recommend Ignition Tie-‐Down Straps – Part # 9300)
FIG. 4
LARGE SAFETY PINS
CLEVIS PIN
STRAP HOOK HOLES RAMP STORAGE
BRACKET
STRAP HOOK HOLES (Not Shown)
RAMP MOUNT
RAMP
LARGE SAFETY PIN
STEP 6.After the assembling, place ramp in the middle and using the 2” spring clip – attach it to the frame as shown. Then install the medium safety pin through the ramp & frame and secure with the clevis pin underneath to reduce movement. (SEE FIG.5)
MOUNTING AND LOADING MOTORCYCLE INSTRUCTIONS STEP 1. Insert 2" receiver bar tube into the 2" receiver hitch and secure with a clevis pin (clevis pin not included). This carrier will only mount into a 2" receiver only STEP 2. The loading ramp can be used on either side of the carrier.Make sure lip of ramp is securely hooked into the ramp mount STEP 3. With feet firmly planted and motorcycle in neutral, slowly guide motorcycle up loading ramp onto carrier.Use two people if necessary STEP 4. Secure motorcycle with 2 tie-‐down straps (not included) – We recommend Ignition Tie-‐Down Straps – Part # 9300. Put one of the safety pins into upper hole passing through the spokes of the front wheel and secure with a clevis pin. (See FIG 4) STEP 5. Place the ramp onto the receiver tube as shown allowing the center support to slide into the bracket. Secure with 2" spring clip.
WARNINGS: l THE MOTORCYCLE CARRIER IS INTENDED FOR MOTORCYCLE USE ONLY l Never exceed 500lb capacity or the hitch receiver manufacturer's tongue weight rating l The motorcycle carrier is intended for one motorcycle only l Do not attempt to drive motorcycle onto carrier platform l Always use the ramp to load and unload motorcycle l Always secure loading ramp while vehicle is in motion l Do not sit or start the motorcycle while on carrier l Do not carry flammable items on the carrier l Motorcycle must be in gear while on carrier for transport l The motorcycle carrier is not intended for transporting people l The motorcycle MUST be secured with tie-‐down straps while being transported (straps not included)
(We recommend Ignition Tie-‐Down Straps – Part # 9300) l Safety bolts and clevis pins must be secured through tire spokes before transporting the motorcycle l Check all hardware connections (nuts & bolts) before each use l For added theft security, secure motorcycle with a lock and chain
CLEVIS PIN
MEDIUM PIN
1-‐2" SPRING CLIP
FIG. 5
PARTS LIST
4 LARGE BOLTS WITH LOCKING NUTS
2 LONG BOLTS AND LOCKING NUTS
2 LARGE SAFETY PINS WITH CLEVIS PIN
1 MEDIUM SAFETY PIN WITH CLEVIS PIN
4 MEDIUM BOLTS WITH LOCKING NUT
8 SMALL BOLTS WITH LOCKING NUTS & WASHERS
1-‐2" SPRING CLIP
2 – TIRE CRADLES 2 – BRIDGE SUPPORTS 1 – SUPPORT CHANNEL RECEIVER BAR 2 – RAMP SUPPORTS 1 – RAMP IGNITION PRODUCTS INC IS NOT RESPONSIBLE FOR ANY PROPERTY DAMAGE OR PERSONAL INJURIES DUE TO INCORRECT ASSEMBLY OR IMPROPER USAGE OF THIS MOTORCYCLE CARRIER. PLEASE CHECK YOUR LOCAL LAWS FOR LIGHTING REQUIRMENTS.
FOR MORE INFORMATION PLEASE CONTACT US BY PHONE 1-‐866-‐997-‐5401 OR EMAIL -‐ [email protected]
AJAX, ONTARIO
WWW.IGNITIONPRODUCTS.COM
MANUEL POUR TRANSPORTEUR DE MOTOCYCLETTE INSTRUCTIONS D’ASSEMBLAGE
Placez les deux berceaux de pneu sur les plaques d’assemblage en L. Fixez avec les petits boulons Voir Fig 1.
FIG. 1
Placez la barre de raccord de 2’’ dans la glissière de support dessous des plaques d’assemblage L, alignez les trous et utilisez les boulons longs. Fixez les supports de ponts comme illustré en
utilisant les écrous d’arrêt; fixez les boulons moyens dans les deux cotés respectifs des ponts de support, en passant au travers des supports de rampes et le trou dans les deux cotés des supports de pont en utilisant les écrous d’arrêt (Voir FIG.2)
BERCEAU DE PNEU
PETITS BOULONS ET ÉCROUS
GLISSIÈRE DE SUPPORT
SUPPORTS DE RAMPES
SUPPORTS DE PONT
BOULONS & ÉCROUS MOYENS
PLAQUES D’ASSEMBLAGE EN L
BARRE DE RACCORD 2”
BOULONS LONGS
IMAGE D’AGRANDISSEMENT
ET DE ROTATION
IMAGE SECTIONNELLE
AGRANDIE
ÉTAPE 1
ÉTAPE 2
FIG. 2
Ajustez les étapes 1 & 2 au niveau, serrez fermement tout les écrous d’arrêt
Le transporteur est conçu pour charger la motocyclette du coté gauche ou droit en utilisant la rampe. Ils y a trois jeux de trous centraux et 1 jeu de trous du haut dans chaque berceau. Les larges goujons de sécurité et les pinces d’attache sont utilisés dans les trous du haut. Voir FIG 4. Les 4 larges boulons sont utilisés dans les trous du centre pour supporter les pneus de la motocyclette. NOTE Selon la grosseur de votre motocyclette certains boulons peuvent être pas nécessaires. (voir FIG.3)
FIG. 3
Le pneu avant de la motocyclette doit reposer dans le berceau et doit être fixé avec un goujon de sécurité large et une pince d ‘attache. Cette étape est nécessaire au cas ou une courroie se briserais ou se relâche durant le transport. Un second goujon de sécurité est fourni. Selon la grosseur de votre motocyclette, celle-‐ci peut être pas nécessaire. Si ce goujon n’est pas utilisé, attachez la motocyclette avec une courroie (Pas incluse). Nous recommandons des Cordon Courroies de Ignition – Part # 9300.
FIG. 4
Goujons de sécurité larges
PINCE D’ ATTACHE
TROUS POUR LES CROCHETS DE COURROIES
SUPPORT DE REMISAGE DE RAMPE
TROUS POUR LES CROCHETS DE COURROIES (Pas illustré)
CHARNIÈRE DE RAMPE
RAMPE
GOUJON DE SÉCURITÉ LARGE
ÉTAPE 3
ÉTAPE 4
ÉTAPE 5
Après l’assemblage, placez la rampe au milieu en utilisant la fixation à ressort ½ ‘’ pour sécuriser, le goujon pour fixer et le maillon d’attache pour placer et réduire le mouvement (Voir FIG.5)
FIG. 5
INSTRUCTIONS DE MONTAGE ET DE CHARGEMENT DE LA MOTO ÉTAPE 1. Insérez la barre de raccord 2’’ dans le réceptacle d’attelage 2’’ et fixez avec une goupille.(Goupille pas incluse) Ce transporteur s’adapteras seulement dans un réceptacle d’attelage 2’’ ÉTAPE 2. La rampe de chargement peut être utilisé de chaque coté du transporteur. Assurez vous que la lèvre de la rampe est accroché sécuritairement dans la charnière de la rampe ÉTAPE 3. Avec les fermement au sol et la motocyclette au neutre, guidez lentement la motocyclette en haut de la rampe sur le transporteur.Utilisez deux personnes si nécessaire ÉTAPE 4. Sécurisez la motocyclette avec deux courroies à rochet (pas incluses). Nous recommandons des Cordon Courroies de Ignition – Part # 9300. Placez un des goujons de sécurité dans un trou supérieur en passant entre les rayons de la roue avant, assurez avec une pince d’attache (Voir FIG 4) ÉTAPE 5. Placez la rampe sur le tube réceptacle comme illustré en permettant que le support central glisse dans la fixation. Fixez avec la fixation à ressort 2’’
AVERTISSMENTS: • LE TRANSPORTEUR DE MOTOCYCLETTE EST CONÇU POUR MOTOCYCLETTE SEULEMENT • Ne jamais dépasser la capacité de 500lbs (227 kg) ou la capacité de l’attelage indiqué par le fabricant • Le transporteur de motocyclette est conçu pour une moto seulement • N’essayez pas conduire la moto sur le transporteur • Utilisez toujours la rampe pour charger et décharger la motocyclette • Toujours sécuriser la rampe de chargement lorsque le véhicule est en mouvement • Ne vous assoyez pas sur la ou ne démarrez pas la motocyclette lorsque que sur le transporteur • Ne transportez pas des produits inflammable sur le transporteur • La motocyclette DOIT ÊTRE embrayée lorsque sur le transporteur • Le transporteur de motocyclette n’est pas conçu pour transporter des personnes • La motocyclette doit être attachée avec des courroies à cliquet lors de transport (Courroies pas incluses)
Nous recommandons des Cordon Courroies de Ignition – Part # 9300 • Les goujons de sécurité et les pinces d’attache doivent être installé entre les rayons de roue avant de transporter la
motocyclette • Vérifiez toute la quincaillerie (boulons et écrous) avant chaque utilisation • Pour une sécurité antivol, attachez la motocyclette avec un cadenas et une chaîne
PINCE D’ ATTACHE
GOUJON RAPIDE
FIXATION À RESSORT 1-‐2"
ÉTAPE 6
LISTE DE PIÈCES
4 LARGES BOULONS AVEC ÉCROUS D’ ARRÊT
2 LONGS BOULONS AVEC ÉCROUS D’ ARRÊT
2 LARGES GOUJON DE SÉCURITÉ AVEC PINCES D’ ATTACHE
1 GOUJON RAPIDE AVEC PINCES D’ ATTACHE
4 BOULONS MÉDIUM AVEC ÉCROUS D’ ARRÊT
8 PETITS BOULONS AVEC ÉCROUS D’ ARRÊT & RONDELLES
1-‐2" AGRAFE-‐RESSORT
2 – BERCEAUX DE PNEU 2 – SUPPORTS DE PONT 1 – GLISSIÈRE DE SUPPORT ET BARRE DE RACCORD 2 – SUPPORTS DE RAMPES 1 – RAMPE IGNITION PRODUCTS INC N’EST PAS RESPONSABLE DES DOMMAGES À LA PROPRIÉTÉ OU DES BLESSURES PERSONNELLES CAUSÉS PAR UN ASSEMBLAGE INCORRECT OU UN USAGE INAPPROPRIÉ DE CE TRANSPORTEUR DE MOTOCYCLETTE. VÉRIFIEZ LES LOIS LOCALES POUR LES ÉCLAIRAGES ADÉQUATS.
POUR PLUS D'INFORMATIONS S'IL VOUS PLAIT NOUS CONTACTER PAR LE TELEPHONE 1-‐866-‐997-‐5401 OU L'E-‐MAIL -‐ [email protected]