7Á&6ä6â þG D þ Ù ] fGYGsG GG · 2015-01-28 · No. 663 201 5 º 1 v 7Á&"6ä6â þG D þ Ù ] fGYGsG GG g ¡ UT -MT20 /MT32 g K)F _ /GtGYGQGV f'à d GAG2Gy A /²&g GwGgGy f
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
No. 663
2015年 1月
電磁開閉器・制御器 仕様変更ニュース
形 名 UT-MT20/MT32形 接続導体ユニット
変更箇所 コイル定格表示ラベル
変更内容
接続する電磁接触器のコイル定格の表示方法を変更します。
※詳細は添付取扱要項(HE19C990)をご参照願います。
【 従来 】 【 変更後 】
コイル定格 表示方法
コイル定格ラベルを製品に添付
組合せる電磁接触器のコイル定格に応じて
お客様にてご選択・貼付け
コイル定格ラベルが製品に貼付け済み
組合せる電磁接触器のコイル定格電圧を
お客様にてご記入
変更理由 ① お客様の作業性向上
② 紙使用量・梱包部材削減による,環境負荷低減
識別方法 目 視
従来との関係 互換性あり
切換時期 2015年 5月生産分より順次
備 考
添付資料 なし
(1/1)
取外し / Removing取付け / Mounting
UT-SA21/SA23の取付け/Attachment of UT-SA21/SA23UT-SA21/SA23 UT-MT20(D)用 UT-MT32(D)用
For UT-MT20(D) For UT-MT32(D)
Trashbox
21
・UT-SA21/SA23の端子を一部切り取って, 取り付けてください Cut off part of the terminal before attaching UT-SA21/SA23.・UT-SA22/SA25は取り付けできません/Cannot attach UT-SA22/SA25.
安全上のご注意
Safety precautions
取付, 配線工事, 操作および保守 ・ 点検の前には, 必ず本紙と各構成機器に付属の書類をよくお読みの上, 正しくご使用ください。Please read this instruction manual and enclosed documents, before startingmounting, operation, maintenance and inspections to ensure correct usage.
・UT-MT20D/MT32Dは必ず取付ベースユニットと 組合せてご使用ください(裏面参照) Use MOUNTING BASE when using UT-MT20D/MT32D. (See reverse side.) ・ラベルに操作コイル電圧を記入してください Write the coil voltage of contactor on the label.
1000 万回10 million operations
8.5mm 8.5mm
単線Solid
適用電線/Applicable wire
締付トルクTightening torque
より線Stranded1.25 - 2mm2
1.25 - 2mm2 1.25 - 3.5-
2-S3.51.0 - 1.5 N・m
φ1.6#16 - #14 (AWG)
スリーブ付より線With end sleeve
圧着端子Lug terminal
ねじサイズScrewsizeコイル
端子CoilTerminal M3.5
端子仕様/ Terminal Specification
(*1) 取付ベースユニットを組合わせて使用した場合の機械的耐久性は1000万回です Mechanical durability is 10 million times when using a Mounting Base.
UT-MT20/MT32:1 ~ 8UT-MT20D/MT32D: ① ~ ⑥
①
⑥
④
⑤
③
②
配線 /Wiring・丸圧着端子を配線する時は一度カバーを 外してください Take off the terminal cover once before wiring a ring rug.・制御回路は必ずUT-MT**の端子に接続し, 電磁接触器のコイル端子に配線しないでください Control circuit must be connected to the terminals of UT-MT, not to the coil terminals of magnetic contactor.
組合せ機器/ Combination
組付け/ Attachment
取付ベースユニットとの組合せ/ Usage with a Mounting Base 可逆式電磁接触器との組合せ/Usage with a reversing type magnetic contactor・ 取付ベースユニットを2つ使用し , 可逆連結ブロック UT-RT** で連結してください Use 2 units of mounting base and joint them with the jointing block UT-RT**.
1
2UT-BT20/BT32/BT32D
3
M4x20(UT-BT20/BT32/BT32Dに添付)(Attached to UT-BT20/BT32/BT32D)
2
1
取付け/Mounting
2
1
取外し/Removing
160+
1 0
UT-RT** の表示 (A) と UT-BT** の側面 (B) を合わせて取り付けてください
Match the indication (A) of UT-RT** and the side (B) of UT-BT**