10-1 Chapter Ten: Master Parts Manual LasTec Articulator Model 721X Master Parts Manual Manual Part Number: Man-721X LasTec A Division of Wood-Mizer Products, Inc. 7865 N County Rd 100E Lizton, Indiana 46149 Phone (317) 892-4444 Fax (317) 892-4188 www.lastec.com
102
Embed
721X owner ops - Lastecgateway.lastec.com/manuals/Parts/721xmas.pdf · Chapter 10: Parts Manual LasTec Articulator Owner Manual Parts Index Model 721X 10-6 Parts Index Listed By Part
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Ref No. Part No. Part No. Part No. Part No. Part No. Part No. Part Description1 F120 F120 F120 F120 F120 F120 1"-8 Nylock Nut2 F168 (*1) F168 (*1) F168 (*1) F168 F168 F168 1" SAE Flat Washer3 P109 P109 P109 P109 P109 P109 Bronze Bushing, 1" ID4 Not Used Not Used Not Used P247 Not Used Not Used 90 Degree Street Elbow, 1/2" NPT5 W134 W134 W134 W134 Gearbox Channel Weldment, HCM66/SGCM500
(*1) Originally P115 & P116 Brass & Zinc Wear Washers, have been replaced with F168 1" SAE Flat Washers. P115 & P116 are nolonger available.
NOTE: The location of these washers may vary depending on model.
(*2) Originally P129-M Gearbox, which utilized the P148 PTO Shaft, which are both no longer available. If converting from a P129-M toa P196-M, you will also need to order either a P225 PTO Shaft or a P207 Splined Yoke to upfit your existing PTO shaft.
(*3) Originally P220 Gearbox, has been replaced with the P196-M Gearbox. The P220 is no longer available. If converting from a P220to a P196-M, you will also need to order (1) W134 Gearbox Channel Weldment and (1) W135 Slide Bar Weldment.
(*4) Originally P250 Gearbox, has been replaced with the P196-M The P250 is no longer available. If converting from a P250 to aP196-M you will also need to order (1) W134 Gearbox Channel Weldment and (1) W135 Slide Bar Weldment.
(*5) Originally L109-M Swivel Cover, has been replaced with the P128-M Universal Swivel Cover. The L109-M is no longer available.
(*6) P131 & P281 each include (2) F187 1/4-20 x 3/4" G8 Bolts.
(*7) Originally P132 Pillow Block with Eccentric Lock Collar. If converting to P208, new mounting hardware will also be needed. (SeeFig. 2.03 for listing.) Also, P208 includes (1) F178 5/16-24 x 5/16" Nylock Set Screw and (1) P107 1/4-28 Straight Grease Zerk.
(*8) P208 Includes (1) F178 5/16-24 x 5/16" Nylock Set Screw and (1) P107 1/4-28 Straight Grease Zerk.
(*9) Used only with P132 Pillow Block Bearing.
For your convenience, we have compiled two indexes of all illustrated Articulator parts and the illustration(s) inwhich they appear. These indexes are contained in the following section of this manual. The first index of parts islisted in order by part number, followed by an index of parts listed in order by part description. Simply locate thepart number or description in either index, and turn to the corresponding illustration number(s) to view the part forphysical verification and/or actual application(s).
Part NumbersThis is the part number you should
use when ordering the part.
Not UsedIf, due to an engineering change, an
illustrated part is discontinued orreplaced, the term “Not Used”
appears in the column under theappropriate serial numbers.
FootnotesChanges which may include important information have
footnotes (*1) listed next to the corresponding part number.Please be sure to read and understand these notes, as they willaid you in identifying and ordering the correct parts for the serial
number series of your Articulator.
Part DescriptionThis is the part description you
should use when ordering the part.
Reference NumbersParts shown in the corresponding
Illustration will each post a referencenumber. Find this reference number
on the spreadsheet for properinformation about that part.
Serial NumbersEngineering changes made to the Articulator aretracked by serial number. If a change affects a
part in the illustration, serial number breakdownsindicating when the change was implemented are
listed at the top of the spreadsheet. Assembly IllustrationThis references the proper
illustration which corresponds withthe spreadsheet
Go to www.lastec.com for latest changes in this manual.
Chapter 10: Parts Manual LasTec Articulator Owner ManualParts Index Model 721X
10-4
Go to www.lastec.com for latest changes in this manual.
LasTec Articulator Owner Manual Chapter 10: Parts ManualModel 721X Parts Index
040237 Deck Weldment, X7, DBS XM-3.06P417 Delrin Wear Pad, 1" ID x 8" DIA XM-2.01P420 Delrin Wear Pad, Belt Cover XM-3.08W468 Discharge Extension Weldment, 521X XM-3.10W479 Dual Whl Yoke Leg Mnt Wldmnt, LF XM-4.04W477 Dual Whl Yoke Leg Mnt Wldmnt, RT XM-4.04W480 Dual Wheel Yoke Leg Weldment, LF XM-4.04W478 Dual Wheel Yoke Leg Weldment, RT XM-4.04W482 Dual Wheel Yoke Weldment, LF XM-4.07W476 Dual Wheel Yoke Weldment, RT XM-4.07
F05009-76 Eye Bolt, 1/2-13 x 2" XM-5.06M140 Fender XM-3.09 XM-3.09 XM-3.09 XM-3.09W425 Fender Weldment, Rear, Center XM-3.09W417 Fender Weldment, Rear, Left XM-3.09W418 Fender Weldment, Rear, Right XM-3.09P443 Gas Spring Cylinder XM-5.01A241 Gas Spring Cylinder Assembly XM-5.01
Go to www.lastec.com for latest changes in this manual.
LasTec Articulator Owner Manual Chapter 10: Parts ManualModel 721X Parts Index
10-15
Parts IndexListed By Part Description
Part No. Part Description Illustration Number(s)
P264 PTO Male Shaft Yoke, Bondioli XM-1.03P277 PTO Outer Shaft Shield, Bondioli XM-1.03P268 PTO Outer Shield Assembly, Bondioli XM-1.03P270 PTO Outer Shield Bearing, Bondioli XM-1.03P274 PTO Shaft, Female, Bondioli XM-1.03P275 PTO Shaft, Male, Bondioli XM-1.03P256 PTO Shield Retaining Chain, Bondioli XM-1.03P272 PTO Twist Sleeve Assembly, Bondioli XM-1.03P260 PTO Yoke Assy, Twist Rel, F, Bond XM-1.03P261 PTO Yoke Assy, Twist Rel, M, Bond XM-1.03P276 PTO Yoke Shield, Female Side, Bond XM-1.03P278 PTO Yoke Shield, Male Side, Bondioli XM-1.03P225 PTO, Bondioli, 29.9/45.1, Splined XM-1.03W394 Pull Arm Weldment, Left XM-1.01W395 Pull Arm Weldment, Right XM-1.01C544 Pull Bar L-Pin XM-1.02W491 Pull Bar Weldment, NXS XM-1.02W398 Pull Bar Weldment, XS XM-1.02T159 Pull Pin, SQHD, XS XM-1.02T156 Pulley, Double, XS XM-3.01 XM-3.01AP418 Pulley, Drive, 2B5V154 XM-2.01P408 Pulley, Idler XM-2.03T160 Pulley, Quad, XS XM-3.01 XM-3.01AC576 Retro Anti-Scalp Roller Tube XM-4.10P111 Ring, Kick-Out, 1” ID XM-4.06 XM-4.07 XM-4.08
F04203-11 Rivet, 3/16" x 1/4" XM-3.08F05015-30 Screw, 5/16” x 3/4”, Self-Tapping XM-5.04
F05005-118 Screw, SFH, 1/4-20 x 1" XM-3.08F05009-75 Screw, Wing, 1/4-20 x 1/2" XM-4.11F05009-77 Screw, Wing, 3/8-16 x 5/8" XM-3.08
P293 Seal, TRB, 1 1/8" ID XM-4.09T133 Spacer, 1 1/4” ID x 1” XM-4.07 XM-4.08T132 Spacer, 1 1/4” x 1/4” XM-1.01 XM-4.01 XM-4.07 XM-4.08T104 Spacer, 1" ID x 1 3/4" OD x 1/4" XM-3.03 XM-4.06 XM-5.01T107 Spacer, 1" ID x 1" XM-3.02 XM-4.06T180 Spindle Spacer, 1" XM-3.01
018309 Spindle, Extended XM-3.01 XM-3.01AT157 Spindle, Keyed XM-3.01 XM-3.01AW473 Spring Plate Weldment, Left XM-5.02 XM-5.03W472 Spring Plate Weldment, Right XM-5.02 XM-5.03P416 Spring, Compression, 2" x 6" XM-1.01P464 Spring, Extension, 1 3/16" x 7 1/2" XM-5.02 XM-5.03P410 Spring, Extension, 1" x 7" XM-2.03P430 Spring, Torsion, 180°, LH XM-3.08P459 Spring, Torsion, 180°, RH XM-3.08W414 Stud Weldment, 3/8-16 x 6 ½” XM-3.08
F05004-111 Stud, Press-In, 1/2-20 x 1 13/16" XM-4.03 XM-4.05F05004-112 Stud, Press-In, 5/16-24 x 3/4" XM-4.09
W460 Swivel Wheel Leg Weldment, X1 XM-4.02W461 Swivel Wheel Leg Weldment, X3 XM-4.02P190 Tapered Roller Bearing, 1" ID XM-4.01 XM-4.03 XM-4.05P187 Tire/Rim Assy, Pneumatic, 16.5 x 6.5 XM-4.03 XM-4.05C554 Trim, Rubber, 9 1/2" XM-3.08W420 Turnbuckle End Weldment, 1/2”, LH XM-4.01 XM-4.03 XM-4.05W354 Turnbuckle End Weldment, 1/2”, RH XM-4.01 XM-4.03 XM-4.05W419 Turnbuckle End Wldmnt, 1” Fixed, LH XM-4.01 XM-4.03 XM-4.05W353 Turnbuckle End Wldmnt, 1” Fixed, RH XM-4.01 XM-4.03 XM-4.05W421 Turnbuckle End Wldmnt, Sliding, LH XM-4.05W357 Turnbuckle End Wldmnt, Sliding, RH XM-4.05M102 Turnbuckle Guard, Fixed, Left XM-4.01 XM-4.03 XM-4.05M101 Turnbuckle Guard, Fixed, Right XM-4.01 XM-4.03 XM-4.05M104 Turnbuckle Guard, Sliding, Left XM-4.05M103 Turnbuckle Guard, Sliding, Right XM-4.05T154 Turnbuckle Shoulder Bolt XM-4.01 XM-4.03 XM-4.05T153 Turnbuckle, 3/4-16 XM-4.01 XM-4.03 XM-4.05
Go to www.lastec.com for latest changes in this manual.
Chapter 10: Parts Manual LasTec Articulator Owner ManualParts Index Model 721X
10-16
Parts IndexListed By Part Description
Part No. Part Description Illustration Number(s)
F05011-75 Washer, 1 1/4" ID x 1 3/4" ID x 1/8" XM-4.01 XM-4.02F05011-4 Washer, 3/8” XM-1.01F05011-44 Washer, Fender, 3/8" XM-3.08F05011-50 Washer, Fender, 5/16” XM-3.10
Ref. No. Part No. Part No. Part No. Part Description1 W394 W394 W394 Pull Arm Weldment, Left2 W395 W395 W395 Pull Arm Weldment, Right
W397 (*2) Weight Transfer Rod Weldment, Fixed3 W483 W483 Weight Transfer Rod Weldment, Fixed, NXS4 P416 P416 P416 Spring, Compression, 2" x 6"5 P244 P244 P244 Lift Pin Assembly6 P183 P183 P183 Clevis Pin, 1" DIA x 4 1/2"7 NOT USED NOT USED 029096 Pivot Pin Weldment
10 P114 P114 P114 Lynch Pin, 3/16"11 P113 P113 P113 Lynch Pin, 1/4"12 NOT USED T132 T132 Spacer, 1 1/4” x 1/4”13 NOT USED NOT USED F05007-27 Bolt, 3/8-16 x 3/4”14 NOT USED NOT USED F05011-4 Washer, 3/8”15 P107 P107 P107 Grease Zerk, 1/4-28 Straight
Notes(*1) Machines prior to serial number 6720397 which have had a K417 Pull Bar Upgrade Kit installed,
should use the 6720397 to 10810798 column to order parts.
(*2) Machines before serial number 6720397 which have had a K417 Pull Bar Upgrade Kit installedrequire the W483 Weight Transfer Rod Weldment.
(*3)Machines prior to serial number 6720397 did not require the second 3/4" bushing (illustrated)which is required for machines as of serial number 6720397. Machines prior to 6720397 whichhave had the K417 Pull Bar Upgrade Kit installed require the second bushing.
(*4)Although Machines prior to Serial Number 6720397 are originally equipped with P109 BronzeBushings, we recommend replacing them with P787 Steel Bushings. If installing steel bushingson these machines, you will also need to install T132 Spacers between the bushings and theball swivels located on the pull arms.
Go to www.lastec.com for latest changes in this manual.
P109 (*5) P109 (*5) P109 (*5) Bushing, Bronze, 1" ID7 P787 (*5) Bushing, Steel, 1" ID8 F05009-69 Not Used Not Used Not Used Bolt, 1-8 x 3", G89 F05011-53 Not Used Not Used Not Used Washer, Split Lock, 1"10 Not Used T159 T159 T159 Pull Pin, SQHD, XS11 Not Used P113 P113 P113 Lynch Pin, 1/4"12 Not Used Not Used C544 C544 Pull Bar L-Pin
Notes(*1) Machines prior to serial number 6720397 which have had a K417 Pull Bar Upgrade Kit installed,
should use column 6720397 to Present when ordering parts for this assembly.
(*2) Machines prior to serial number 6720397 which have had a K417 Pull Bar Upgrade Kit installed,require the W491 Pull Bar Weldment.
(*3) The quantity of F113 Washers will vary due to the assembly and alignment process.
(*4) Originally P115 Brass Wear Washer, has been replaced with the P116 Zinc Wear Washer. TheP115 is no longer available.
(*5)Although machines prior to serial number 6720397 used the P109 Bronze Bushing, and machines asof 6720397 used the P787 Steel Bushing, these bushings are 100% interchangeable, and you maysubstitute one for the other at your discretion.
Go to www.lastec.com for latest changes in this manual.
14 T160 (*1) T160 (*1) T160 (*1) T160 (*1) T160 (*1) Pulley, Quad, XS15 P427 P427 P427 P427 P427 Belt, B-6016 NOT USED T180 (*2) NOT USED T180 (*2) NOT USED Spindle Spacer, 1"
Notes(*1) The T156 Double Pulley is utilized on decks X1 & X3 - X7. The T160 Quad Pulley is utilized on deck X2.
(*2)
Machines within this serial number range were originally equipped with T157 Spindles and T180 SpindleSpacers, which have been replaced with 018309 Extended Spindles, which do not require the T180 SpindleSpacers. The T157 & T180 are still available, but it is recommended that they be replaced with the 018309Extended Spindle on machines within this serial number series, making the T180 Spacer unnecessary. Ifconverting from T157 to 018309 Spindles, you will also need to replace the F05009-80 5/8-18 x 2 1/4” Boltswith F05008-95 5/8-18 x 1 1/4” Bolts.
(*3) All machines are equipped with P128 High-Lift Blades standard, but there are other blades available,including the P246 21" Low-Lift Blade, and the P322 21" Gator Mulching Blade.
(*4)The F05009-80 Bolt is utilized with the T157 Spindle & T180 Spindle Spacer ONLY. If you are replacing theT157 Spindle & T180 Spacer with the 018309 Extended Spindle on machines within this serial numberseries, you will also need to replace the F05008-80 Bolt with the F05008-95 Bolt in each spindle.
(*5)
Machines prior to Serial No. 1367099 utilized F05011-27 5/8" Split Lock Washers in this location. Thesehave been replaced with the F05011-40 5/8" Flat Washers and the 028350 Nylon Blade Washers (seeIllustration XM-3.01A, next page). It is recommended that all machines prior to Serial No. 1367099 beupfitted with the F05011-40 & 028350 washers on all blade bolts. To upfit your machine to the new stylewashers, order the 040250 Nylon Blade Washer Kit.
NOTE: The 018309 Extended Spindles CANNOT BE INSTALLED on machines from Serial Numbers 1010295 to1600895, or from Serial Numbers 1620895 to 1630895.
Go to www.lastec.com for latest changes in this manual.
F05011-27 (*2) Washer, Split Lock, 5/8"12 F05011-89 (*2) Washer, Flat, 5/8" ID x 2 1/2" ODF05008-95 Bolt, 5/8-18 x 1 1/4"13 F05009-80 (*4) Bolt, 5/8-18 x 2 1/4"
14 T160 (*1) T160 (*1) Pulley, Quad, XS15 P427 P427 Belt, B-6016 NOT USED (*2) 028350 (*2) Washer, Nylon Blade
Notes(*1) The T156 Double Pulley is utilized on decks X1 & X3 - X7. The T160
Quad Pulley is utilized on deck X2.
(*2)
Machines prior to Serial No. 1367099 utilized F05011-27 5/8" SplitLock Washers in this location. These have been replaced with theF05011-89 5/8" Flat Washers and the 028350 Nylon Blade Washers.It is recommended that all machines prior to Serial No. 1367099 beupfitted with the F05011-89 & 028350 washers on all blade bolts. Toupfit your machine to the new style washers, order the 040250 NylonBlade Washer Kit.
(*3)All machines are equipped with P128 High-Lift Blades standard, butthere are other blades available, including the P246 21" Low-LiftBlade, and the P322 21" Gator Mulching Blade.
(*4)
The F05009-80 Bolt is utilized with the T157 Spindle & T180 SpindleSpacer ONLY. If you are replacing the T157 Spindle & T180 Spacerwith the 018309 Extended Spindle on machines within this serialnumber series, you will also need to replace the F05008-95 Bolt withthe F05008-95 Bolt in each spindle.
Go to www.lastec.com for latest changes in this manual.
(*1)The high & low pivot slide bar assemblies both take the same W358 Pivot Slide BarWeldment. It is simply inverted as to locate the ball swivel to either the top or bottom of thebar. Refer to Figure XM-3.06 for the proper pivot slide bar locations & orientations.
(*2) The F05009-69 Bolt & the F05004-154 Bolt are to be tightened with a torque wrench to150 Ft. Lbs.
(*3)
Machines prior to Serial No. 13820699 utilized jam nuts, hex nuts, and split lock washers inthese locations. These have been replaced with the F05010-161 2-Way Locking Nut,F05011-62 Flat Washer, and the F05010-122 Half Nylock Nut. Machines prior to13820699 should be upfitted with the new style hardware. If upfitting to the new stylehardware, order the 040249 Slide Bar Hardware Upfit Kit.
Go to www.lastec.com for latest changes in this manual.
Figure XM-3.03: Common Leg Pivot Slide Bar Assemblies
Go to www.lastec.com for latest changes in this manual.
Chapter 10: Master Parts Manual LasTec Articulator Owner's ManualSection 3: Cutting Decks Model 721X
10-42
Figure XM-3.04: Deck Pivot Arm AssembliesSerial Numbers
From 1010295 6710397To 6700297 Present
Ref. No. Part No. Part No. Part Description1 W383 W383 Deck Pivot Arm Weldment, X7 (Right)2 W378 W378 Deck Pivot Arm Weldment, X6 (Left)3 W416 W416 Deck Pivot Arm Rod Weldment
F05013-71 Bolt, 3/4-10 x 2"4 F05009-36 Bolt, 3/4-10 x 3"F05009-36 Bolt, 3/4-10 x 3"5 F05009-54 Bolt, 3/4-10 x 3 1/2"
Notes(*1) The quantity of F05011-62 Washers may vary due to the assembly & alignment procedures.
(*2) On machines prior to serial number 6710397, the F05009-36 Bolt screwed directly intomounting plate on the deck, making the F05010-103 Nut unnecessary.
Go to www.lastec.com for latest changes in this manual.
Ref. No. Part No. Part No. Part No. Part No. Part No. Part No. Part No. Part Description1 (*1) (*1) (*1) (*1) (*1) (*1) (*1) Pivot Slide Bar Assy, High2 (*1) (*1) (*1) (*1) (*1) (*1) (*1) Pivot Slide Bar Assy, Low3 (*1) (*1) (*1) (*1) (*1) (*1) (*1) Pivot Slide Bar Assy, Com Leg
(*1)The two loose P442 "Outer Deck" Warning Decals located in the front of this manual are tobe affixed to each of the two rear fenders of the tractor, preferably near the operatingcontrols.
Go to www.lastec.com for latest changes in this manual.
(*1)The M112 Main Deck Cover & related hardware, M130 End Plate & related hardware, &M132 End Plate & related hardware are only used on machines which have been convertedto 5 cutting decks (521X).
Go to www.lastec.com for latest changes in this manual.
Go to www.lastec.com for latest changes in this manual.
Chapter 10: Master Parts Manual LasTec Articulator Owner's ManualSection 3: Cutting Decks Model 721X
10-52
Figure XM-3.09: Fender AssembliesSerial Numbers
From 1010295 1450895 6950497 11200998To 144895 6940497 11190898 Present
Ref. No. Part No. Part No. Part No. Part No. Part Description1 M140 M140 NOT USED (*2) NOT USED (*3) Fender
W417 Fender Weldment, Rear, Left2 M140 M140 NOT USED (*3) FenderW425 Fender Weldment, Rear, Center3 M140 M140 NOT USED (*3) FenderW418 Fender Weldment, Rear, Right4 M140 M140 NOT USED (*3) Fender
5 F05011-105 (*1) F05011-105 (*1) F05011-105 (*1) NOT USED (*3) Washer, Fender, 5/16” x 1/8”6 F05006-5 F05006-5 F05006-5 NOT USED (*3) Bolt, 5/16-18 x 3/4”
F05006-1 Bolt, 5/16-18 x 1”7 F05006-5 F05006-5 NOT USED (*3) Bolt, 5/16-18 x 3/4”
Notes
(*1)Machines from Serial Number 1010295 to 10810798 were equipped with F05011-50 5/16” FenderWashers on the fenders. They have been replaced with F05011-105 5/16” x 1/8” Thick Washers.We recommend that you replace these washers on all the fenders.
(*2) As of Serial Number 6950497, the front fenders are no longer used. Rear fenders only.
(*3) As of Serial Number 112000998, fenders are no longer used on the Ariculator.
Go to www.lastec.com for latest changes in this manual.
From 1010295 1550895 1760995 10820798To 1540895 1750995 10810798 Present
Ref. No. Part No. Part No. Part No. Part No. Part Description1 NOT USED (*1) W384 (*2) W384 W384 Grass Chute Weldment, Guarded2 NOT USED (*1) F05006-1 F05006-1 F05006-1 Bolt, 5/16-18 x 1”3 NOT USED (*1) F05011-50 F05011-50 F05011-50 Washer, Fender, 5/16”4 NOT USED (*1) F05011-16 F05011-16 F05011-16 Washer, Flat, 5/16”5 NOT USED (*1) F05010-58 F05010-58 F05010-58 Nut, Nylock, 5/16-186 W468 (*3) W468 (*3) W468 (*3) W468 (*3) Discharge Extension Weldment, 521X7 F05006-1 (*3) F05006-1 (*3) F05006-1 (*3) F05006-1 (*3) Bolt, 5/16-18 x 1”8 F05011-105 (*4) F05011-105 (*4) F05011-105 (*4) F05011-105 (*4) Washer, Fender, 5/16” x 1/8”9 F05011-16 (*3) F05011-16 (*3) F05011-16 (*3) F05011-16 (*3) Washer, Flat, 5/16”10 F05010-58 (*3) F05010-58 (*3) F05010-58 (*3) F05010-58 (*3) Nut, Nylock, 5/16-18
Notes(*1) On Machines prior to Serial Number 1550895, the grass chutes were an integral part of the cutting
decks. Removable grass chutes & related hardware were not used on these machines.
(*2)Machines prior to Serial Number 1760995 were originally equipped with M115 Grass Chutes, which didnot include the guard. The M115 has been replaced with the W384 Guarded Grass Chute. The M115 isno longer available.
(*3) The W468 Discharge Extension & related hardware are only used on machines which have beenconverted to 5 cutting heads (521X).
(*4)Machines from Serial Number 1010295 to 10810798 were equipped with F05011-50 5/16” FenderWashers on the grass chutes. They have been replaced with F05011-105 5/16” x 1/8” Thick Washers.We recommend that you replace these washers on all the grass chutes.
Go to www.lastec.com for latest changes in this manual.
Ref. No. Part No. Part No. Part No. Part No. Part No. Part DescriptionC529 NOT USED C529 Chain, Safety, 100”1
C547 NOT USED C547 C547 Chain, Safety, 78”2 P449 P449 NOT USED P449 P449 P449 Chain Snap Link, 1/4”3 NOT USED C546 NOT USED C546 NOT USED NOT USED Chain Mount Plate, Safety
Notes
(*1)On machines from Serial Number 2201195 to 2980296, the safety chain & related hardware were not standardequipment. To upfit a machine within this serial number series with a safety chain, order an A246 Safety ChainAssembly, which includes (1) C547 Chain, (2) P449 Snap Links, and (2) C546 Mounting Plates.
Go to www.lastec.com for latest changes in this manual.
Ref. No. Part No. Part No. Part Description1 T154 NOT USED Turnbuckle Shoulder Bolt2 W419 NOT USED Turnbuckle End Weldment, 1” Fixed, LH3 T153 NOT USED Turnbuckle, 3/4-164 W420 NOT USED Turnbuckle End Weldment, 1/2”, LH
F05009-71 NOT USED Bolt, AH, 1/4-20 x 5/8", SSF05005-120 NOT USED Bolt, AH, 1/4-20 x 1", SSF05005-121 NOT USED Bolt, AH, 1/4-20 x 1 1/4", SSF05005-122 NOT USED Bolt, AH, 1/4-20 x 1 1/2", SS
5 (*2)
F05005-119 NOT USED Bolt, AH, 1/4-20 x 1 3/4", SS6 F05010-9 NOT USED Nut, Keps, 1/4-207 W352 NOT USED Wheel Arm Weldment, 13", Left8 F05012-21 NOT USED Cotter Pin, 3/16" x 1"9 P447 NOT USED Cotter Pin, 1/8" x 1 1/2"10 F05012-23 NOT USED Cotter Pin, 3/16" x 1 1/2"11 P203 NOT USED Bushing, Bronze, 1 1/4" ID12 F05011-2 NOT USED Washer, Flat, 1/2" SAE13 F05010-8 NOT USED Nut, Nylock, 1/2-1314 P435 NOT USED Bushing, Bronze, 1 1/4" ID x 1"
T132 NOT USED Spacer, 1 1/4" ID x 2" OD x 1/4"15 F05011-75 NOT USED Washer, 1 1/4" ID x 1 3/4" ID x 1/8"16 P191 NOT USED Bearing Seal, 1 1/4" ID17 P190 NOT USED Tapered Roller Bearing, 1" ID18 P433 NOT USED Bearing Washer, 3/4" ID19 P434 NOT USED Nut, Castle, 3/4-1620 P195 NOT USED Hub Cap21 A250 (*3) NOT USED Wheel Assembly, 13 x 5, Urethane Filled22 P107 NOT USED Grease Zerk, 1/4-28, Straight23 M102 NOT USED Turnbuckle Guard, Fixed, Left25 W370 NOT USED Wheel Arm Weldment, 13", Right26 W353 NOT USED Turnbuckle End Weldment, 1” Fixed, RH27 W354 NOT USED Turnbuckle End Weldment, 1/2”, RH28 M101 NOT USED Turnbuckle Guard, Fixed, Right29 P289 (*3) NOT USED Bearing Race Insert, 1" ID TRB
Notes
(*1)On machines from Serial Numbers 1010295 to 2011095, the 13” tires & pivot arms areused on decks X1, X3, X6, & X7. On machines from Serial Numbers 2021095 to 6710397,the 13” tires & pivot arms are used only on decks X6 & X7.
(*2)The length of the allen head bolt will vary in each turnbuckle due to the assembly andalignment process. All five possible lengths are listed here. Simply match them with theactual bolt(s) in your turnbuckle(s).
(*3) The A240 Wheel Assembly includes (2) P289 Bearing Race Inserts.
(*4) As of Serial Number 6710397, the 13” tires & pivot arms are not used. They have beenreplaced with 9” urethane-filled wheel yoke assemblies & wheel spacers.
Go to www.lastec.com for latest changes in this manual.
Go to www.lastec.com for latest changes in this manual.
Chapter 10: Master Parts Manual LasTec Articulator Owner's ManualSection 4: Wheels Model 721X
10-66
Figure XM-4.02: Swivel Wheel Leg AssemblySerial Numbers
From: 1010295 1640895 2021095 6720397
To: 1600895 (*1) 2011095 (*2) 6710397 Present(*3)
1620895,Also: 1630895 1610895
Ref. No. Part No. Part No. Part No. Part No. Part Description1 NOT USED NOT USED W460 NOT USED Swivel Wheel Leg Weldment, X12 NOT USED NOT USED W461 NOT USED Swivel Wheel Leg Weldment, X33 NOT USED NOT USED P107 NOT USED Grease Zerk, 1/4-28 Straight4 NOT USED NOT USED F05013-3 NOT USED Bolt, 3/4-10 x 4"5 NOT USED NOT USED F05011-62 NOT USED Washer, Flat, 3/4" SAE6 NOT USED NOT USED F05010-103 NOT USED Nut, Nylock, 3/4-107 NOT USED NOT USED F05012-23 NOT USED Cotter Pin, 3/16" x 1 1/2"8 NOT USED NOT USED F05011-75 NOT USED Washer, 1 1/4" ID x 1 3/4" OD x 1/8"
Notes
(*1)On machines from Serial Number 1010295 to 1600895, plus 1620895 & 1630895, 9” wheels were notstandard equipment. These machines were equipped with 13” tires & pivot arms on decks X1 & X3. Ifyou would like to convert a machine within this serial number range to 9” swivel wheels, order a K410Swivel Wheel Retro-Fit Kit.
(*2)On machines from Serial Number 1640895 to 2011095, plus 1610895, 9” wheels were not standardequipment. These machines were equipped with 13” tires & pivot arms on decks X1 & X3. If you wouldlike to convert a machine within this serial number range to 9” swivel wheels, order a K412 SwivelWheel Retro-Fit Kit.
(*3) As of Serial Number 6720397, the 9” swivel wheel legs are welded directly to the cutting decks, thusmaking the bolt-on legs & related hardware unnecessary.
Go to www.lastec.com for latest changes in this manual.
Ref. No. Part No. Part No. Part Description1 W365 W365 NOT USED Wheel Arm Weldment, 16.5", Fixed, Right2 P109 P109 NOT USED Bushing, Bronze, 1" ID3 NOT USED (*2) P294 (*4) NOT USED Grease Zerk, 1/4-28, 45°4 P193 P193 NOT USED Cotter Pin, 5/32" x 1 3/4"5 F05012-21 F05012-21 NOT USED Cotter Pin, 3/16" x 1"6 F05012-23 F05012-23 NOT USED Cotter Pin, 3/16" x 1 1/2"7 T154 T154 NOT USED Turnbuckle Shoulder Bolt8 W353 W353 NOT USED Turnbuckle End Weldment, 1", Fixed, RH9 T153 T153 NOT USED Turnbuckle, 3/4-1610 W354 W354 NOT USED Turnbuckle End Weldment, 1/2", RH11 F05011-2 F05011-2 NOT USED Washer, Flat, 1/2"12 F05010-8 F05010-8 NOT USED Nut, Nylock, 1/2-1313 F05010-9 F05010-9 NOT USED Nut, Keps, 1/4-20
F05009-71 F05009-71 NOT USED Bolt, AH, 1/4-20 x 5/8", SSF05005-120 F05005-120 NOT USED Bolt, AH, 1/4-20 x 1", SSF05005-121 F05005-121 NOT USED Bolt, AH, 1/4-20 x 1 1/4", SSF05005-122 F05005-122 NOT USED Bolt, AH, 1/4-20 x 1 1/2", SS
14 (*3)
F05005-119 F05005-119 NOT USED Bolt, AH, 1/4-20 x 1 3/4", SS15 P187 P187 NOT USED Tire/Rim Assembly, Pneumatic, 16.5 x 6.516 P195 P195 NOT USED Hub Cap17 P192 P192 NOT USED Nut, Castle, 1"-1418 P190 P190 NOT USED Bearing, Tapered Roller, 1" ID19 P194 P194 NOT USED Nut, Lug, 1/2-20 x 13/16" Tapered20 P289 (*4) P289 (*4) NOT USED Bearing Race Insert, 1" ID TRB21 F05004-111 (*4) F05004-111 (*4) NOT USED Stud, Press-In, 1/2-20 x 1 13/16"22 P191 P191 NOT USED Bearing Seal, 1 1/4" ID23 M101 M101 NOT USED Turnbuckle Guard, Fixed, Right24 C489 C489 NOT USED Axle25 P188 (*4) P188 (*4) NOT USED Hub Assembly, 1" ID TRB, Demountable26 W355 W355 NOT USED Wheel Arm Weldment, 16.5", Fixed, Left27 W419 W419 NOT USED Turnbuckle End Weldment, 1", Fixed, LH28 W420 W420 NOT USED Turnbuckle End Weldment, 1/2" LH29 M102 M102 NOT USED Turnbuckle Guard, Fixed, Left
Notes
(*1)On machines as of Serial Number 6950497, the 16.5” tires, pivot Arms, & turnbuckles located onthe front of the decks have been replaced with urethane-filled 9” dual wheel yoke assemblies &wheel spacers.
(*2) Machines prior to Serial Number 2031095 were not equipped with the P294 Zerk, unless the hubhas been replaced since October of 1995. All P188 Hubs now include the zerk.
(*3)The length of the allen head bolt will vary in each turnbuckle due to the assembly and alignmentprocess. All five possible lengths are listed here. Simply match them with the actual bolts usedin your turnbuckles.
(*4) The P188 Hub Assembly includes (1) P294 Grease Zerk, (2) P289 Bearing Race Inserts, & (4)F05004-111 Press-In Studs.
Go to www.lastec.com for latest changes in this manual.
Ref. No. Part No. Part No. Part No. Part Description
NOT USED W478(Shown) NOT USED Dual Wheel Yoke Leg Weldment, Right
(Shown)1NOT USED W480
(Not Shown) NOT USED Dual Wheel Yoke Leg Weldment, Left(Not Shown)
NOT USED W477(Shown) NOT USED Dual Wheel Yoke Leg Mount Weldment, Right
(Shown)2NOT USED W479
(Not Shown) NOT USED Dual Wheel Yoke Leg Mount Weldment, Left(Not Shown)
3 NOT USED F05009-36 NOT USED Bolt, 3/4-10 x 3”4 NOT USED F05011-62 NOT USED Washer, Flat, 3/4” SAE5 NOT USED F05011-6 NOT USED Washer, Split Lock, 3/4”6 NOT USED F05010-7 NOT USED Nut, Hex, 3/4-107 NOT USED F05009-69 NOT USED Bolt, 1-8 x 3”8 NOT USED F05010-109 NOT USED Nut, Nylock, 1-89 NOT USED F05009-44 NOT USED Bolt, 3/4-10 x 2 1/2”10 NOT USED P107 NOT USED Grease Zerk, 1/4-28 Straight
Notes
(*1)Machines prior to Serial Number 6950497 were equipped with 16.5” tires & pivot Arms on thefront of the main deck, and the bolt-on dual wheel yoke legs are not used. If you would like toconvert your machine to dual wheel yokes, order a K450 Dual Wheel Retro-Fit Kit.
(*2) As of Serial Number 7640697, the dual wheel legs are welded directly to the deck, and the bolt-on dual wheel yoke legs are no longer used.
Go to www.lastec.com for latest changes in this manual.
31 NOT USED (*3) NOT USED (*3) P294 Grease Zerk, 1/4-28, 45°32 C489 (*4) C489 (*4) C489 (*4) Axle, Drilled33 F05012-23 (*4) F05012-23 (*4) F05012-23 (*4) Cotter Pin, 3/16" x 1 1/5"
Notes
(*1)The length of the allen head bolt will vary in each turnbuckle due to the assembly andalignment process. All five possible lengths are listed here. Simply match them with theactual bolts used in your turnbuckles.
(*2) The P188 Wheel Hub includes (4) F05004-11 Studs, (2) P289 Inserts, & (1) P294 Zerk.
(*3)As of Serial Number 2031095, the P294 Zerk located in the P188 Hub became standardequipment. Machines prior to Serial Number 2031095 do not have this zerk unless the hubhas been replaced. All P188 Hubs now include the zerk.
(*4) The C489 Drilled Axle & hardware are used in the center wheel arm location only. The left& right wheel arms use the W415 Flagged Axle Weldment & hardware.
Go to www.lastec.com for latest changes in this manual.
Ref. No. Part No. Part No. Part No. Part No. Part Description1 NOT USED W118 W118 W118 Wheel Yoke Weldment, 9” Swivel RT2 NOT USED W688 W688 W688 Wheel Yoke Weldment, 9” Swivel LF3 NOT USED A150 A150 A150 Wheel Assembly, 9” x 3.5”, UF4 NOT USED P296 P296 P296 Bearing Spacer, 3/4” ID x 1/2”, SS5 NOT USED F05013-70 F05013-70 F05013-70 Bolt, 3/4-10 x 6 1/2”6 NOT USED NOT USED (*2) F05011-62 F05011-62 Washer, Flat, 3/4” SAE7 NOT USED F05010-103 F05010-103 F05010-103 Nut, Nylock, 3/4-108 NOT USED P109 P109 P109 Bushing, Bronze, 1” ID9 NOT USED T107 T107 T107 Spacer, 1” ID x 1”10 NOT USED T104 T104 T104 Spacer, 1” ID x 1/4”11 NOT USED NOT USED (*3) NOT USED (*3) P843 Washer, Wave, 1” ID12 NOT USED P110 P110 P110 Clevis Pin, 3/8” x 1 5/16”13 NOT USED P111 P111 P111 Ring, Kick-Out, 1” ID
Notes
(*1)Machines prior to Serial Number 2021095 did not include 9” swivel wheel yokes as standard equipment.These machines will only need 9” swivel wheel yokes & related hardware if a K410 or K412 SwivelWheel Leg Retro-Fit Kit has been installed.
(*2) Machines prior to Serial Number 2870196 did not include the F05011-62 Washers as standardequipment. However, It is recommended that they be installed on all machines.
(*3) Machines prior to Serial Number 6720397 did not include the P843 Wave Washers as standardequipment. However, it is recommended that they be installed on all machines.
Go to www.lastec.com for latest changes in this manual.
Ref. No. Part No. Part No. Part Description1 NOT USED W476 Dual Wheel Yoke Weldment, RT2 NOT USED W482 Dual Wheel Yoke Weldment, LF3 NOT USED A150 Wheel Assembly, 9” x 3.5”, UF4 NOT USED T125 Bearing Spacer, 3/4” ID x 3/8”5 NOT USED T126 Bearing Spacer, 3/4” x 11/16”6 NOT USED W481 Axle Weldment, Dual Wheel7 NOT USED F05010-34 Nut, Nylock, 5/8-108 NOT USED P203 Bushing, Bronze, 1 1/4” ID9 NOT USED T133 Spacer, 1 1/4” ID x 1”10 NOT USED T132 Spacer, 1 1/4” ID x 1/4”11 NOT USED P844 Washer, Wave, 1 1/4” ID12 NOT USED P212 Clevis Pin, 3/8” x 2 1/8”13 NOT USED P111 Ring, Kick-Out, 1” ID
Notes
(*1)Machines prior to Serial Number 6950497 did not include the dual wheel yokes as standardequipment. These machines will only need dual wheel yokes & related hardware if a K450Dual Wheel Yoke Leg Kit has been installed.
Go to www.lastec.com for latest changes in this manual.
Ref. No. Part No. Part No. Part Description1 NOT USED W686 Wheel Yoke Weldment, Fixed, RT2 NOT USED W685 Wheel Yoke Weldment, Fixed, LF3 NOT USED A150 Wheel Assembly, 9” x 3.5”, UF4 NOT USED P296 Bearing Spacer, 3/4” ID x 1/2”, SS5 NOT USED T126 Bearing Spacer, 3/4” x 11/16”6 NOT USED F05010-122 Nut, Nylock, 3/4-107 NOT USED P109 Bushing, Bronze, 1” ID8 NOT USED T107 Spacer, 1” ID x 1”9 NOT USED T104 Spacer, 1" ID x 1/4”10 NOT USED P843 Washer, Wave, 1” ID11 NOT USED P110 Clevis Pin, 3/8” x 1 5/16”12 NOT USED P111 Ring, Kick-Out, 1” ID
Notes
(*1)Machines prior to Serial Number 6720497 did not include the 9” fixed wheel yokeassemblies & related hardware as standard equipment. They were equipped with 13” tires& pivot arms
Complete left and right yoke assemblies can be ordered under part numbers: A631 -- Wheel Yoke Assy, 9 in Fxd LF XS/ER, includes items 2 through 12A632 -- Wheel Yoke Assy, 9 in Fxd Rt XS/ER, includes Item 1 and items 3 through 12
Go to www.lastec.com for latest changes in this manual.
Go to www.lastec.com for latest changes in this manual.
Chapter 10: Master Parts Manual LasTec Articulator Owner's ManualSection 4: Wheels Model 721X
10-80
Figure XM-4.09: 9” Wheel AssemblySerial Numbers
From: 1010295 2021095To: 2011095 (*1) Present
Ref. No. Part No. Part No. Part Description1 NOT USED A150 (*2) Wheel Assembly, 9" x 3.5", UF2 NOT USED A149 (*3) Wheel/Rim Assembly, UF3 NOT USED P291 (*4) Wheel Hub/Bearing Assembly, 3/4" TRB, DM4 NOT USED P297 (*5) Wheel Hub Assembly, DM5 NOT USED P294 Grease Zerk, 1/4-28 x 45°6 NOT USED F05004-112 Stud, Press-In, 5/16-24 x 3/4"7 NOT USED P402 Bearing Race Insert, 3/4" ID, TRB8 NOT USED P292 Bearing, Tapered Roller, 3/4" ID9 NOT USED P293 Seal, TRB, 1 1/8" ID10 NOT USED F05005-101 Bolt, 1/4-20 x 1"11 NOT USED F05011-14 Washer, Split Lock, 1/4"12 NOT USED F05010-63 Nut, Hex, 1/4-2013 NOT USED F05010-142 Nut, Lug, 5/16-24 Tapered
Notes
(*1)Machines prior to Serial Number 2021095 did not include 9” wheels as standard equipment.These machines only need 9” wheels & related hardware if a K410 or K412 Swivel WheelLeg Retro-Fit Kit, or a K450 Dual Wheel Leg Retro-Fit Kit has been installed.
(*2) The A150 Wheel Assembly includes all components illustrated.
(*3) The A149 Wheel/Rim Assembly includes (4) F05005-101 Bolts, (4) F05011-14 Washers, &(4) F05010-63 Nuts.
(*4) The P291 Wheel Hub/Bearing Assembly includes (1) P297 Wheel Hub Assembly, (2) P292Bearings, & (2) P293 Seals.
(*5) The P297 Wheel Hub Assembly includes (4) F05004-112 Studs, (2) P402 Bearing RaceInserts, & (1) P294 Grease Zerk.
Go to www.lastec.com for latest changes in this manual.
Ref. No. Part No. Part No. Part No. Part Description1 P438 P438 P438 Anti-Scalp Wheel, 6” x 3.5” x 3/4” ID2 P122 NOT USED NOT USED Clevis Pin, 3/4” DIA x 4 1/2”3 F05012-63 NOT USED NOT USED Hitch Pin, #2164 NOT USED F05008-106 F05008-106 Bolt, 1/2-13 x 4 3/4”
NOT USED C576 (*2) Retro Anti-Scalp Roller Tube5 C575 (*3) Anti-Scalp Roller Tube6 NOT USED F05010-127 F05010-127 Nut, Half Nylock, 1/2-13
Notes
(*1)
Machines from Serial Number 1010295 to 7630697 are equipped with clevis pins and hitch pins,rather than bolts, tubes, & nuts, unless an 019693 Anti-Scalp Plate Rebuild Kit has beeninstalled. To convert a machine within this serial number range to the bolt/tube system, order aK430 Anti-Scalp Wheel Rebuild Kit. If an 019693 Kit has been installed, use the 7750797 toPresent column to order parts. If a K430 Kit has been installed, use the 7640697 to 7740797column to order parts.
(*2)Machines from Serial Number 7640697 to 7740797 are equipped with anti-scalp wheel plateswith 3/4” holes, which require the C576 Retro Anti-Scalp Roller Tube. If an 019693 Anti-ScalpPlate Rebuild Kit has been installed (which has 1/2” holes), use the 7750797 to Present columnto order parts.
(*3)Machines from Serial Number 7750797 to Present are equipped with anti-scalp wheel plateswith 1/2” holes, which require the C575 Anti-Scalp Roller Tube. Machines prior to SerialNumber 7750797, which have had an 019693 Kit installed, should use the 7750797 to Presentcolumn to order parts.
Go to www.lastec.com for latest changes in this manual.
Ref. No. Part No. Part No. Part Description1 P121 NOT USED Hydraulic Cylinder, PP, 3/8" NPT2 P198 NOT USED Hydraulic Fitting, 1/4" JIC-1/4" NPT, 90°3 W385 NOT USED Cylinder Pull Arm Weldment4 W392 NOT USED Cylinder Pivot Block Weldment, Left5 W390 NOT USED Cylinder Pivot Block Weldment, Right6 C444 NOT USED Cylinder Tie Rod7 W389 NOT USED Cylinder Base Weldment8 W393 NOT USED Lift Arm Weldment9 W388 NOT USED Lift Arm End Weldment, Left10 W387 NOT USED Lift Arm End Weldment, Right11 F05012-63 NOT USED Hitch Pin, #21612 F05012-23 NOT USED Cotter Pin, 3/16" x 1 1/2"13 P109 NOT USED Bushing Bronze, 1” ID14 P116 NOT USED Washer, 1 1/16" ID x 1 3/4" OD x 1/8"15 T104 NOT USED Spacer, 1" ID x 1 3/4" x 1/4"16 F05011-6 NOT USED Washer, Split Lock, 3/4"17 F05010-7 NOT USED Nut, Hex, 3/4-1018 P411 NOT USED Clevis Pin, 1" DIA x 3 1/8"19 A241 NOT USED Gas Spring Cylinder Assembly20 P443 NOT USED Gas Spring Cylinder21 P448 NOT USED Ball Stud Retaining Clip22 P444 NOT USED Ball Stud, 10 MM DIA x 5/16-18 x 1/2"23 P113 NOT USED Lynch Pin, 1/4"24 P199 NOT USED Hydraulic Fitting, 1/4” JIC – 1/4” NPT, Straight25 P223 NOT USED Hydraulic Fitting Adapter, 1/4” NPT – 3/8” NPT
Notes
(*1)Machines after Serial Number 1440895, and machines prior to 1450895, which have had aK400 Hydraulic Lift Retro-Fit Kit installed, are equipped with a new hydraulic lift assembly.Refer to Illustrations XM-5.02 & XM-5.03 for parts for the new assembly.
Go to www.lastec.com for latest changes in this manual.
Ref. No. Part No. Part No. Part No. Part Description1 NOT USED P121 P121 (*2) Hydraulic Cylinder, PP, 3/8" NPT
NOT USED P198 P198 Hydraulic Fitting, 1/4” JIC-1/4” NPT, 90°2 NOT USED Hydraulic Fitting, 1/4" JIC-3/8" NPT, 90°3 NOT USED W434 W434 Cylinder Pivot Arm Weldment, LF4 NOT USED W433 W433 Cylinder Pivot Arm Weldment, RT5 NOT USED C527 C527 Cylinder Tie Rod, 3/4"6 NOT USED W435 W435 Cylinder Base Plate Weldment7 NOT USED W432 W432 Lift Arm Weldment, 3/4-10 Thread8 NOT USED W431 W431 Lift Arm Slide Tube Weldment9 NOT USED NOT USED (*3) NOT USED (*3) Deck Lift Arm Weldment, Rear, LF10 NOT USED NOT USED (*3) NOT USED (*3) Deck Lift Arm Weldment, Rear, RT11 NOT USED P464 P464 Spring, Extension, 1 3/16" x 7 1/2"12 NOT USED W473 W473 Spring Plate Weldment, Left13 NOT USED W472 W472 Spring Plate Weldment, Right14 NOT USED P223 NOT USED (*5) Hydraulic Fitting Adapter, 1/4” NPT – 3/8” NPT
Ref. No. Part No. Part No. Part No. Part Description1 P121 (*2) P121 (*2) P121 Hydraulic Cylinder, PP, 3/8" NPT
P198 P198 Hydraulic Fitting, 1/4” JIC-1/4” NPT, 90°2 P445 Hydraulic Fitting, 1/4" JIC-3/8" NPT, 90°3 W434 W434 W434 Cylinder Pivot Arm Weldment, LF4 W433 W433 W433 Cylinder Pivot Arm Weldment, RT5 C527 C527 C527 Cylinder Tie Rod, 3/4"6 W435 W435 W435 Cylinder Base Plate Weldment7 W432 W432 W432 Lift Arm Weldment, 3/4-10 Thread8 W431 W431 W431 Lift Arm Slide Tube Weldment9 W471 W471 W471 Deck Lift Arm Weldment, Rear, LF10 W470 W470 W470 Deck Lift Arm Weldment, Rear, RT11 P464 P464 P464 Spring, Extension, 1 3/16" x 7 1/2"12 W473 NOT USED (*4) NOT USED (*4) Spring Plate Weldment, Left13 W472 NOT USED (*4) NOT USED (*4) Spring Plate Weldment, Right14 NOT USED (*5) NOT USED (*5) NOT USED (*5) Hydraulic Fitting Adapter, 1/4” NPT – 3/8” NPT
Notes
(*1)Machines prior to Serial Number 1450895 are equipped with the original hydraulic lift assembly.Refer to Illustration XM-5.01 for parts for the original assembly. Machines prior to SerialNumber 1450895 which have had a K400 Hydraulic Lift Retro-Fit Kit installed should usedcolumn 2021095 – 2191195 for parts ordering.
(*2)
Machines from Serial Number 1840995 to 2780198 were originally equipped with P200Hydraulic Cylinders, which required P198 Fittings. The P200 has been replaced with the P121Cylinder, and is no longer available. If converting from a P200 to a P121 Cylinder on machineswithin this serial number range, you will also need to order either (2) P445 Fittings or (2) P223adapters to use with your existing fittings.
(*3)Machines prior to Serial Number 2021095 did not include the W470 & W471 Rear Deck LiftArms & related hardware as standard equipment. These parts are only used if a K400Hydraulic Lift Retro-Fit Kit has been installed.
(*4) As of Serial Number 2201195, the W472 & W473 Spring Plate Weldments are integral parts ofdecks X4 & X5.
(*5) As of Serial Number 1840995, P445 3/8” NPT Fittings are used, which do not need the P2231/4” NPT – 3/8” NPT Adapters.
Go to www.lastec.com for latest changes in this manual.
Ref. No. Part No. Part No. Part No. Part No. Part Description1 NOT USED P121 P121 P121 Hydraulic Cylinder, PP, 3/8" NPT2 NOT USED W434 W434 W434 Cylinder Pivot Arm Weldment, LF3 NOT USED W433 W433 W433 Cylinder Pivot Arm Weldment, RT4 NOT USED C527 C527 C527 Hydraulic Cylinder Tie Rod, 3/4"5 NOT USED W435 W435 W435 Cylinder Base Plate Weldment6 NOT USED W432 W432 W432 Lift Arm Weldment, 3/4-10 Thread7 NOT USED W431 W431 W431 Lift Arm Slide Tube Weldment8 NOT USED F05013-71 F05013-71 F05013-71 Bolt, 3/4-10 x 2"9 NOT USED F05011-6 F05011-6 F05011-6 Washer, Split Lock, 3/4"10 NOT USED F05011-62 F05011-62 F05011-62 Washer, Flat, 3/4" SAE11 NOT USED P113 P113 P113 Lynch Pin, 1/4"12 NOT USED P463 P463 P463 Clevis Pin, 1" DIA x 3 1/2"13 NOT USED P116 (*2) P116 (*2) P116 (*2) Washer, 1 1/16" ID x 1 3/4" x 1/8"14 NOT USED P464 P464 P464 Spring, Extension, 1 3/16" x 7 1/2"15 NOT USED F05010-109 F05010-109 F05010-109 Nut, Nylock, 1"-816 NOT USED F05012-21 F05012-21 F05012-21 Cotter Pin, 3/16" x 1"17 NOT USED P114 P114 P114 Lynch Pin, 3/16"18 NOT USED NOT USED (*3) W470 W470 Deck Lift Arm Weldment, Rear, RT19 NOT USED NOT USED (*3) W471 W471 Deck Lift Arm Weldment, Rear, LF20 NOT USED W473 W473 NOT USED (*4) Spring Plate Weldment, Left21 NOT USED W472 W472 NOT USED (*4) Spring Plate Weldment, Right
Notes
(*1)Machines prior to Serial Number 1450895 are equipped with the original hydraulic lift assembly. Refer toIllustration XM-5.01 for parts for the original assembly. Machines prior to Serial Number 1450895 whichhave had a K400 Hydraulic Lift Retro-Fit Kit installed should used column 2021095 – 2191195 for partsordering.
(*2) The quantity of P116 Washers will vary due to the assembly & alignment process.
(*3)Machines prior to Serial Number 2021095 did not include the W470 & W471 Rear Deck Lift Arms &related hardware as standard equipment. These parts are only used if a K400 Hydraulic Lift Retro-Fit Kithas been installed.
(*4) As of Serial Number 2201195, the W472 & W473 Spring Plate Weldments are integral parts of decks X4 &X5.
Go to www.lastec.com for latest changes in this manual.
Ref. No. Part No. Part No. Part Description1 NOT USED F05015-30 F05015-30 Screw, 5/16” x 3/4”, Self-Tapping2 NOT USED P440 P440 Clamp, Hydraulic Hose, 1/2”3 W424 W424 NOT USED (*2) Hydraulic Hose Support Loop Weldment
Notes
(*1)The P440 Clamp & related hardware became standard equipment on machines as of SerialNumber 1280795. They can be added to machines prior to 1280795 by simply drilling a mounthole in the top of the cross tube.
(*2) As of serial number 1610895, the W424 Hydraulic Hose Support Loop is an integral part of theW399 Gearbox Channel Weldment.
Go to www.lastec.com for latest changes in this manual.
Go to www.lastec.com for latest changes in this manual.
Chapter 10: Master Parts Manual LasTec Articulator Owner's ManualSection 5: Hydraulic Lift Model 721X
10-96
Figure XM-5.05: Lift Cables, Serial Numbers 1010295 - 1440895Serial Numbers
From: 1010295 1450895To: 1440895 Present (*1)
Ref. No. Part No. Part No. Part Description1 P413 NOT USED Cable, Lift, X22 P414 NOT USED Cable, Lift, X1/X3
Notes
(*1)As of Serial Number 1450895, the lift cables are no longer used. On machines prior to SerialNumber 1450895, we recommend removal of these cables and installation of a K400 HydraulicLift Retro-Fit Kit.
Go to www.lastec.com for latest changes in this manual.
Ref. No. Part No. Part No. Part Description1 P413 NOT USED Cable, Lift, X22 P414 NOT USED Cable, Lift, X1/X33 F05010-147 NOT USED Nut, Hex, 9/16-124 F05011-81 NOT USED Washer, Star, 9/16"5 T161 NOT USED Cable Lift End6 F05010-149 NOT USED Nut, Nylock, 5/16-247 F05009-79 NOT USED Bolt, 5/16-18 x 2", G88 F05011-17 (*1) NOT USED Washer, Flat, 5/16"9 F05010-58 NOT USED Nut, Nylock, 5/16-1810 A235 NOT USED Cable Assembly, X1/X311 A236 NOT USED Cable Assembly, X212 F05007-135 NOT USED Bolt, 3/8-16 x 3 1/4"13 F05009-76 NOT USED Eye Bolt, 1/2-13 x 2"14 F05010-35 NOT USED Nut, Hex, 1/2-1315 F05011-61 NOT USED Washer, Flat, 3/8" SAE16 F05011-68 NOT USED Washer, Flat, 1/2"17 F05010-8 NOT USED Nut, Nylock, 1/2-1318 W422 NOT USED Cable Support Loop Weldment19 F05009-62 NOT USED Bolt, 5/16-18 x 1 1/4"20 F05011-16 NOT USED Washer, Flat, 5/16"21 F05010-58 NOT USED Nut, Nylock, 5/16-1822 F05009-70 NOT USED Bolt, 5/16-18 x 1 3/4"23 P440 NOT USED Clamp, Pipe, 1/2"24 C377 NOT USED Cable Retainer Spacer Tube25 F05010-10 NOT USED Nut, Nylock, 3/8-16
Notes(*1) The quantity and location of the F05011-17 Washers will vary due to the assembly and
alignment process.
(*2)As of Serial Number 1450895, the lift cables are no longer used. On machines prior to SerialNumber 1450895, we recommend removal of these cables and installation of a K400 HydraulicLift Retro-Fit Kit.
Go to www.lastec.com for latest changes in this manual.