Assembly Manual 712570303 Building Dimensions 140.25 24.75 6’ x 5’ 69.75” 62” 72” 66” 54” 71” Storage Area Approximate Size Interior Dimensions Exterior Dimensions Roof Edge to Roof Edge 1.8 m x 1.5 m 2.30 m 2 3.97 m 3 177.17 cm 157.48 cm 182.88 cm 167.64 cm 137.16 cm 180.34 cm 6x5 Wall to Wall Depth Sq. Ft. Width Height Width Depth Height Cu. Ft. CAUTION Sharp Edges PATENTS ARE PENDING
26
Embed
CAUTION 712570303...C Part No Name Quantity 10262 Upper Channel (painted) 1 10256 Floor Channel (unpainted) 1 10280 Corner Clip 2 Attach Floor Channel (unpainted) in the same sequence
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
1.8 m x 1.5 m 2.30 m2 3.97 m3 177.17 cm 157.48 cm 182.88 cm 167.64 cm 137.16 cm 180.34 cm
6x5
Wall to Wall
DepthSq. Ft. Width HeightWidth Depth Height Cu. Ft.
CAUTIONSharp Edges
PATENTS ARE PENDING
1
1. Before beginning construction, check local building codes regarding footings, location and otherrequirements. Study and understand this owner’s manual.
2. Follow all directions and dimensions carefully.3. Follow the step sequence carefully for correct results.4. Be sure all the parts fit together properly before proceeding.5. SAFETY FIRST: Care must be taken when handling various pieces of your kit since some contain sharp
edges. Wear work gloves, eye protection and long sleeves when assembling or performing anymaintenance on your building.
6. GROUND MUST BE LEVEL: Be sure Floor Frames lie flat on ground. To prepare earth bed, remove sod andother debris. Level the high spots with flat shovel and tamp the bed down. Refer to Page 24 for Parts List.
Site PreparationBefore You Begin
Foundation RecommendationsLocal building codes vary by region, refer to your local codes for specifications.
Concrete Slab1. Select level site for building.
2. Remove 6” of soil for slab.
3. Compact 4” gravel in hole.
4. Place 6 ml plastic over gravel.
5. Construct 2 x 4 form.
6. Pour concrete and level.
Wood Platform1. Construct with 2 x 4 treated lumber and 5/8” minimum exterior grade
plywood using galvanized nails.
2. Level platform.
68 1/2” (174cm)
56 1
/2”
(14
3,5c
m)
Slab Dimensions
Door Opening
16” Centers
68 1/2” (174cm)
56 1
/2”
(14
3,5c
m)
Door Opening
CAUTIONSharp Edges
BASIC TOOLS
No. 2 PhillipsScrewdriver Pliers Work
Gloves
TapeMeasure
Level
Shovel
RubberMallet
2
Do Not store swimming pool chemicals in your building.Combustibles and corrosives must be stored in air tight
containers.
Care & Maintenance
Finish: For long lasting finish, periodically clean and wax the exterior surface. Touch up scratches as soonas you notice them on your building. Immediately clean the area with a wire brush; wash it and applytouch up paint per manufacturer’s recommendation.
Roof: Keep roof clean of leaves and snow with long handled, soft bristled broom. Heavy amounts ofsnow on roof can damage the building making it unsafe to enter.
Doors: Keep doors closed to prevent wind damage.
Fasteners: Regularly check you building for loose screws, bolts, nuts, etc. and retighten them as necessary.
Moisture: With changing temperatures, condensation will accumulate inside the building.
Other Tips: A noncorrosive caulking is helpful to seal the building.
A
B
Raise Panel at Angle
Overlap Panels and align endsHook edge of top Panel
to bottom Panel
C
3
Step 1 Pre-Assembly Side WallsPart No Name Quantity
10307 Wall Panel 810268 Corner Panel 2
ASSEMBLY COMMON FOR ALL PANELS
CAUTIONSharp Edges
ARROW TO TOP
21
NOTE: ALWAYS COVER THE ARROW!
MAKE TWO (2) SIDE WALL SECTIONS4 Panels & 1 Corner - Each
IMPORTANT
MUST USE FLAT SOLID SURFACEDO NOT SNAP ON GROUND OR GRASS!
Bring Top Panel down flat while maintainingpressure in the middle to keep edge hooked
Push down to snap Panels together workingfrom the center outward in both directions
D E
F G
Start in middle ofassembly to snap panels
together
Push down to snap end ofpanels together
Pre-Assembly Side Walls . . . .cont
4
Apply pressure inarea shown
CAUTIONSharp Edges
IMPORTANT
MUST USE FLAT SOLID SURFACEDO NOT SNAP ON GROUND OR GRASS!
5
Pre-Assembly Side Walls. . . . cont
Install Corner PanelH
CAUTIONSharp Edges
ARROW TO TOP
Push down to snapPanels together
working from thecenter in each direction
3
Cover Arrow onCorner Panel
1
Use edge of surface toallow Corner Panel
to hang down
2
I
J K
Align Channel to PanelRibs and pop intoplace at corner
Continue aligningChannel
and popping into place
6
Pre-Assembly Side Walls. . . . contPart No Name Quantity
10261 Upper Channel (painted) 2
Upper Channel(painted)
2
CAUTIONSharp Edges
ARROW TO TOP
Attach Upper Channel(painted)
Channel
CornerPanel
Corner must be against45° cut on Channel
-IMPORTANT-START ASSEMBLY AT CORNER PANEL
7
L
MAKE TWO (2) SIDE WALL SECTIONS
Floor Channel is Unpainted
Attach Floor Channelin the same sequence
as Upper Channel.
Pre-Assembly Side Walls . . . .contPart No Name Quantity
20 Roof Panel (left) 2 1025121 Roof Panel (right) 2 1025022 Roof Channel 4 1026723 Roof Fascia 4 1032024 Ridge Cap 1 1027025 Peak Cap 226 Corner Cap 427 Door Panel (1/2) 1 1027628 Door Panel 1 1030829 Door Panel 1 1030930 Vertical Door Brace 1 1036131 Vertical Door Brace 1 1036932 Horizontal Door Brace 2 1027533 Diagonal Door Brace 2 10288
Please include your Model Number, Part Number,and Part Name
Separate contents of the carton by the part number while reviewing parts list.Check to be sure that you have all the necessary parts for your building.