D E A B C A - Bit to Center of Stabilizer Blade B - Bit to Bend C - Overall Motor Length D - Max OD of Motor at Stabilizer Upset E - Radius at Kickpad Common Top Connection Common Bottom Connection Recommended Bit Sizes Estimated Weight 22.7 in (577 mm) 53 in (1346 mm) 26.8 ft (8.2 m) 6.9 in (175.3 mm) 3.5 in (89 mm) 4-1/2 IF or XH 4-1/2 REG 7-7/8 in to 8-3/4 in (200 - 222.3 mm) 2900 lbs (1315 kg) General Dimensional Data 6.75” SS100-B5 www.bicodrilling.com Lobes: 7/8 Motor Loads *While Not Operating Continuous Loads - Lay motor down if exceeded Ultimate Loads - Motor may part if exceeded Power Section Specifications Flow Range Speed Ratio No Load Bit Speed No Load Pressure Drop 200 - 600 gpm (757 - 2,271 lpm) .28 rev/gal (.074 rev/l) 56 - 168 rpm 450 psi (31.02 bar) Max Recommended Pressure Torque Slope Torque @ Max Recommended Pressure Power @ Max Recommended Pressure 1,250 psi (86.2 bar) 9.75 ft-lb/psi (191.73 Nm/bar) 12,188 ft-lbs (16,524 Nm) 364 hp (272 kW) 180 135 90 45 0 16,000 12,000 8,000 4,000 0 1200 1000 800 600 400 200 Disclaimer: The Performance Curve and Performance Data published by BICO Drilling Tools are based on recorded dynamometer data at surface temperature (72 degF) on a standard fit configuration between rotor and stator, with clean water, and are presented as a reference to the potential power of the power section and or motor. Downhole conditions such as highly elevated bottom hole temperatures and different drilling/intervention fluids shall require adjusted loose fits that may produce reduced power during surface (dynamometer) testing and will achieve the expected torque and speed values when reaching planned conditions. Contact BICO for the adjusted performance curves. Rated Motor Differential Pressure (psi) Bit Speed (rpm) Torque (ft-lbs) 1400 600 GPM 400 GPM 200 GPM Performance Curve Ultimate Loading Continuous Operation WOB - lbs (kg) Backreaming - lbs (kg) Bit Overpull* - lbs (kg) Body Overpull* - lbs (kg) Slick Motor Hole Size (in) Bend Angle 1.50 1.83 2.00 2.12 2.38 2.60 7-7/8 7.5 10.0 11.3 12.2 14.1 – 8-1/2 5.3 7.8 9.1 10.0 11.9 13.6 8-3/4 4.4 6.9 8.2 9.1 11.0 12.7 7-7/8 10.7 13.4 – – – – 8-1/2 10.6 13.0 14.4 15.4 – – 8-3/4 10.8 13.0 14.2 15.2 17.3 – 7-7/8 9.9 12.6 14.0 – – – 8-1/2 9.7 12.2 13.6 14.6 16.7 – 8-3/4 9.8 12.1 13.4 14.4 16.5 18.4 Stabilized 1/8” UG Hole Size (in) Stabilized 1/4” UG Hole Size (in) Predicted Build Rates *This condensed Build Rate table is the result of a theoretical geometry analysis of the motor and is presented as guideline for job design and planning. Due to the extensive variability in drilling BHA design, formation characteristics and other external factors, BICO cannot guarantee the values stated in the Build Rate table. Degrees / 100 ft (30 m) BICOBRUTE RUGGED DEMANDS NO LESS Motor: B5 Transmission: Articulated – – 740,000 (335,658) 1,070,000 (485,343) 60,000 (27,215) 29,000 (13,154) 197,000 (89,357) 526,000 (238,589)