Vaxcare:AUST: 1300 36 4040NZ: 0800 800 900Vaxcare:AUST: 1300 36
4040NZ: 0800 800 900www.vax.com.auInstruction ManualMODIFIED AUGUST
2008Please read carefully before using this cleaner.Always fully
extend the mains cable before use.Retain for future
reference.MultifunctionInstruction ManualModel No. V2000 - Sukka -
VHN - Pet VAX - Family VAXVAXCARE Service & Help:AUSTRALIA 1300
36 4040NEW ZEALAND 0800 800 900If you have any queries or concerns
about using your Vax, call VAXCARE. Please make a note of the part
number or model number of the appliance before calling. (Aust only:
Mon-Fri. 10.00am to 6.00pm. EST)Calls are charged at the local
rate.An answerphone is available out of these hours. There are over
300 approved Vax Service Agents in Australia and New Zealand. For
the nearest Service Agent, please refer to your Vax warranty or
call VAXCARE or visit www.vax.com.auTechnical SpecicationWeight:Net
8.0KgSize:Height 54cms x 34cms diameterMotor:1200 watts max. / 450
watts min variable power. 2 stage bypass motor completely insulated
and sealed against water contamination.Structure:Moulded
high-impact resistant ABSDust Bags: Supplied with machine.Clean
Water Reservoir:4 litres of clean water.RecoveryBucket:8 litre
capacity.Hose:1.8m long, crush resistant hose with 360 (degree)
swivels at each end.Subject to technical change without notice.21.
Important Safety InformationTHIS EASY GUIDE SHOULD BE
READCOMPLETELYANDREFERREDTOAT ALL TIMES BEFORE USING YOUR VAX.This
easy guide should be retained with your VAX for future
reference.IfyourVAXissoldortransferredtoanew
owner,thisguideshouldbepassedonso that the new owner can become
acquainted withthemachineandthisinformation.The following
information is provided in the interest of safety.Please read it
before using your VAX.DOSUse only genuine VAX replacement parts.Use
of non VAX uids, lters and accessories
maydamageyourmachineandvoidyour
warranty.Ensurethemainscableisfullyunwound and straightened before
use.Ifthesupplycordisdamaged,itmustbe replaced by the manufacturer
or its service agent or a similarly qualied person in order to
avoid a hazard.Ensurethemainscableiskeptwellaway
fromtherevolvingbrushes(wheretted) ofyourVAX,whenitisturnedonand
running.Keep the mains cable away from heat, oil, sharp edges and
rough surfaces and avoid damage in any other
way.Exerciseextremecarewhencleaningstair carpets. Ensure that your
VAX is in a stable positionateitherthetoporbottomofthe
stairswithoutover-stretchingthehose
orcable.Whencleaningthestairtreads, always keep a hand rmly on your
VAX. You may prefer to remove the
castors.Followtheinstructionsinthisuserguide when tting accessories
or tools.Remove the plug from the wall socket before
carryingoutanymaintenancespeciedin this
guide.Changedustbagandltersatregular intervals.Store your VAX in a
dry place.HaveyourVAXservicedbyanauthorised VAX Service Agent only
using genuine VAX spare parts.DONTSThisapplianceisnotintendedforuse
byyoungorinrmpersonsunlessthey havebeenadequatelysupervisedbya
responsible person to ensure that they can use the appliance
safely.Youngchildrenshouldbesupervised
toensurethattheydonotplaywiththe appliance.Never drag your VAX by
the mains cable.Never tug at the mains cable to remove the plug
from the wall socket.Neverallowthecompletecoiledmains cable to drop
on the oor as this may result inkinksorknotsoccurringinthecable,
causing premature failure.Dontletanyonetouchtherotatingbrush
bar(wheretted)unlessyourVAXis disconnected from the
mains.NeveruseyourVAXinthepresenceof ammable
gases.Avoidsuckinguphotitems,hazardous
liquidsoranyothermaterialwhichcould damage your VAX.Never leave
your VAX running unattended.Never use your VAX without a dust
bag.If your VAX fails to operate, never attempt to repair it
yourself as repairs carried out by an unauthorised or inexperienced
person may cause injury to you or damage to your VAX and void your
warranty.Never alter the specication or modify your VAX in any
way.EXTENSION CABLEIf using an extension cable always ensure that
the insulation sheath is in good condition and is not damaged in
any way.Make sure that the plug and socket are tted
totheextensioncablecorrectly,ifindoubt have it checked by a qualied
electrician.Always use the extension cable in accordance with the
manufacturers instructions.IMPORTANT:Whencarryingoutany
maintenanceorcleaningoperationsonthis product, it is essential that
the plug is removed from the wall socket.In the interests of
product improvement, theCompanyreservestherightto
introducemodicationsoralterations without notice.112.
TheSockFilterthat encasestheHEPA lter,actsasapre-lterandprotectsit
fromthemajorityof dust.TocleantheSock
FiltergentlypeelitbackfromtheHEPA
(Fig/14.2).Shaketoremovetheexcessdirtand
handwashatnormaltemperature.Do notmachinewashortumbledry.Donot
replacethesockwhenitisstilldampor
wet.WhenreplacingtheSockFilteronthe HEPA ensure that the sock is
pulled down completely all round.TheSockFiltercanbecleanedupto
5timesinthiswayandshouldthenbe replaced.3.
Withthesockremoved,theHEPAFilter canbecleanedbygentlytappingona
hard surface. The HEPA Filter should never be washed or exposed to
water.VAX recommends that the HEPA Filter be replaced every 12
months to maintain peak performance.TIPThe HEPA lter can also be
cleaned by taking the vacuum outside, removing the HEPA and
vacuumingtheHEPAonlywiththedusting
tool.Ensureallltersarereplacedbefore vacuuming your home.15.
Removing debris from the Mini TurboTool(Model: Pet VAX only.
Optional with other models.)1. Switchthe vacuumcleaner off and
disconnect thepowerplug from the electrical outlet.Rotate orremove
thelockingring (Fig/15.1).2. Liftthetopcover off and remove any
debris (Fig/15.2).3. Tore-assemble, ensurethatthe tabs are engaged.
Pivotthelower housing closed and rotateorreplace thelockingring 180
(Fig/15.3).16. Removing hair from
TurboBrush(Model:PetVAX&FamilyVAXoroptional extra with other
models).Over time hair and lint will build up around the brushbar.
This must be removed to maintain performanceandpreventdamagetothe
tool.1. Switchthevacuumcleaneroffand disconnectthepowerplugfromthe
electrical outlet.2. Turnthebrushbar overandusingapair
ofscissorsrunthe bottom blade along the length of the brushbar
cutting the hair as you go (Fig/16.1).USE SCISSORS WITH
THEPOINTOFTHE BLADEAWAYFROM YOUR BODY.3. Once the hair and lint
around the brush bar hasbeencut,removethehairoutofthe brushes.17.
StorageIMPORTANT:Alwaysunplugthevacuum
cleanerfromtheelectricaloutletandrewind the power cord as directed
before storing.NOTE:Alwaysstorethevacuumcleaner base
down.Replacement3 Filter PackDisposable PaperBags Pack
(5)ReplacementCloth BagMoulded ConeFilter Pack (2)P/N 90630 P/N
90600 P/N 90620 P/N 20310HEPA Filter & SMS Filter CoverP/N
905005. Thewashingtoolisatonthesurface being washed.6.
Thepowercontroliscorrectly adjustedwithinthewashing
range.Turnhigherthan minimumwashsettingfor uneven or higher pile if
required (Fig/12.4).7. There are no kinks in the solution
tube.Remove kinks by rubbing the tube between nger & thumb8.
That the recovery bucket is not full, causing
theautomaticcutoffvalvetostopthe suction.32. Parts Checklist1012.
If You Have Washing DifcultiesIF YOU HAVE WASHING DIFFICULTIES,
CHECK...1. The pump washing button is switched on.2. The tube valve
is properly connected (Fig/12.1).Before using your VAX, please read
Important safety information on page 2.All VAX Multifunctions
include:3. The weight on the end ofthesolutiontubeis
atthebottomofthe waterreservoirand nottrappedbetween
themotorandwater reservoir (Fig/12.2).4. Therocker switchis posi ti
oned t o w a r d s theback (Fig/12.3).13. Looking After Your
VAXItemsbelowareavailablefromyourVax Retailer or from VAX
direct.REGULARLY (when you buy a new pack
of5disposablepaperbagsor1new cloth bag)Replace cone
lterAvailableinapack oftwo.Alsoavailable withabondinilterand
exhaust lter in a 3 lter pack.Clean the Bondini
lterAvailablewithacone lter and exhaust lter in a 3 lter pack. Wash
lter in warm water. Squeeze itdryandreplaceit. Your VAX will work
more efciently if the Bondini lter is replaced with a new one
occasionally.Clean the exhaust lterAvailablewithacone lter and
bondini lter in a 3 lter pack. Wash lter in warm water. Squeeze dry
and replace.Filter housing unitMotor unitWater reservoirFlexible
Suction Hose and Hand gripStainless Steel Extendible WandDust
bagsVAXCarpetCleaningFluidCombination
toolUpholsteryToolDustingBrushCrevice toolUpholsterywashing
toolRecovery bucketFibreflow CarpetWashing ToolLiquid Delivery
TubeOn/off switchVariablespeedcontrolPump on/off switchHyrdo Dry
HardFloor Wash HeadHEPAfilterSpillPick-up ToolMiniTurbo BrushTurbo
BrushHard Floor BrushOther Accessories:14. Looking After Your HEPA
Filter (Model Family VAX and Sukka only. Optional extra with other
models. Contact VAXCARE for information)1. RemovetheHEPA
Filterbyturning a n t i c l o c k w i s e (Fig/14.1).1. Set up for
washing, but dont connect the solutiontubeorputwaterinthewater
reservoir (Fig/11.1).Ifthespillissoapy,VAXDefoamerwillbe requiredin
therecovery bucket.Refer toinstructions onDefoamer bottle. 2. Use
the metal extension tube or extendible wand or connect the washing
tool directly to the hand grip.3. Turn the suction power
tomaximumand switch on (Fig/11.2).4. Suck up the
spill.ThesoundyourVAXmakeswillchange and the suction will drop when
the recovery bucket is full. Time to empty it!3. Dry Vacuuming1.
Fitadustbagby pushing it rmly into the recovery bucket
beforeconnecting hose (Fig/3.1).2. Push the connector on the end of
the hose. Turn it clockwise to lock (Fig/3.2).3.
Fitthelterhousingandmotortothe recovery bucket.Ensure the two
retaining clips are secured. Youmayhavetopushdownhardonthe
edgesofthemotorunitabovetheclips. They are a tight t (Fig/3.3).4.
Fittheextendible wandtothehose hand grip.Adjustwand length by
pressing buttoninthe directionofthe arrow (Fig/3.4).5.
Choosesuctionpowerbyturningthedial located at the front of the
motor.Vacuum carpets on high power.Vacuumfabricsandupholsteryonlow
power.6. Choose the right tool for the job.The smaller tools can be
tted to the back of your VAX when not in use.7. Switch on and begin
vacuuming.TIPAs your VAX is very powerful, you may nd
thatthedustbagllsupquicklytherst time you use
it.Shouldablockageoccurinthesuction hose/hand grip it can usually
be unblocked byreversingthehoseandrunningthe machine for a few
seconds or so. It may be necessary to bind the hand grip end of the
hose with a cloth to form a temporary seal
betweenthehandgripandtheconnector socket on the recovery
bucket.UpholsteryTool:Foruseoncarpet, upholstery, stairs
etcDustingBrush:Forcleaningdelicate surfaces.Crevice Tool: For
cleaning in narrow gaps.MiniTurboBrush:RotatingBrushBar dislodges
hair and lint from upholstery (Model: Pet VAX only).Combination
Tool: Use the lever to switch between vacuuming hard oors and
carpets.Turbo Brush: Rotating Brush Bar dislodges
hairandlintfromcarpets(Model:PetVAX and Family VAX
only).SpillPick-upTool:Takesupsmallliquid spills (Model: Pet VAX
only).For information on accessories contact VAXCARE.4 910. How to
Unblock Sinks1. Set up for washing, but dont connect the extendible
wand, solution tube or put water in the water
reservoir.Ifthewaterinyoursinkissoapy,VAX
Defoamerwillberequiredintherecovery bucket. 2. Wrapacloth aroundthe
bent end tube tocreatea sealbetween thetubeand theplughole
(Fig/10.1).3. Turnthesuctionpowertomaximumand switch
on.ThesoundyourVAXmakeswillchange and the suction will drop when
the recovery bucket is full. Time to empty it!11. How to Suck Up
Large SpillsIf your washing machine oods or the deepfreeze has been
defrosted, leaving pools ofwater about, your VAX can help.Fig/11.2
Fig/10.19. What to Do After WashingAFTER WASHING - ALWAYSKeep your
VAX assembled. Clean the washing tool, stainless steel wand and
hose, by sucking up some clean warm water. After sucking up
thewater,leaveyourVAXswitchedon.Air owing through the hose will
help dry it out.AFTER WASHINGClean out the washing
toolstopreventdirt andresiduefrom drying out (Fig/9.1)8 51Vacuum
the area you intend to wash.2Removethemotorlterhousing,hose, dust
bag and vacuuming tool.3Whendustbagis removed, re-t the
hose.Pushand turnclockwise (Fig/5.1).4Fill the water reservoir
withwarmwater (nothot),tothelevel markedonit.Fitthe
waterreservoirinto therecoverybucket (Fig/5.2).5AddVAXCarpet
Cleanertotheclean water.Refertothe instructionsonthe carpet cleaner
bottle.8. How to Wash Hard Floors(Model Family VAX only. Optional
with other models.) 1. SetupyourVaxasdescribedonpage5
changingthecarpetcleaningsolutionfor hard oor solution. 2.
ConnecttheHydro-dryhardoorwash head to the end of the extendible
wand and t the solution tube to the Hydro-dry head. 3. Switch the
power button ON. 4. Turn suction power to wash setting.5. Start the
washing solution owing. To start thesolutionowthroughthewashhead,
push down the rocker switch on the Hydro
dryheadsothattheswitchispushed towards you (Fig/8.1).This also
lowers the sponge and brushes to scrub the oor surface
(Fig/8.2).6.Glidethe Hydro-dry headbackand forth
overtheoorsurface.Washanareaof around 3 square
metres.7.Tostopthewashingsolutionow,push
therockerswitchforward.Thiswillalso
raisethespongeandbrushesexposing rubber blades. 8.Turn the suction
power to maximum.9.ContinuetomovetheHydro-dryhead
overtheoorsurfacetopickupexcess water.10. Move to the next area and
repeat steps 3 to 9.Sponge &Brushes4. How to Use theSpill
Pick-up Tool (ModelPetVAXonly.Optionalwithother models. Contact
VAXCARE for information)The Spill-pick up tool can be used while
dry vacuuming to pick up small liquid spills.1. Attachthespill
pick-uptoolto thevacuuming hose.TurnyourVAX on.Suckupthe
spillkeeping thespillpick-up facingdown.Do not overll above
themaxlevel mark (Fig/4.1). NOTE: Do not tip the tool upside down
or the uid will leak out.2. Removethespillpick-up from the
hose.Releasetheconnector bypushingtheblack release button and pull
to disconnect.Disposethe spill (Fig/4.2).Fig/4.25. Getting Ready to
Wash3 ITEMS OUTFilter housing unit3 ITEMS INWater reservior with
water and carpet cleanerLiquid delivery tube Dust bagWashing tool
Vacuuming tool3. Separatethepartsand rinse.Drycomponentsbefore
replacing (Fig/4.3).NOTEThespillpick-upis designed to pick-up uid.
Anystainingormarking canbewashedusing yourVAXttedwiththe
appropriate washing tool.9.Tostopthesolutionow,pullthecollar
onthewashtoolbackward.Goback over the area you have just washed.
This willremoveexcessmoisturefromthe upholstery (Fig/7.3).10. Move
to the next area and repeat steps 6 to 9.11.
Whennomorewaterreachesthewash tool the pump will make a sound due
to sucking air.Rellthewaterreservoirwithwaterand
VAXCarpetcleaner.Emptytherecovery bucket when you rell the water
reservoir. The sound your VAX makes will change
andthesuctionwilldropiftherecovery bucket is full. Time to empty
it!TipUsetheupholsterywashingtoolforspot cleaning small patches on
either carpet or upholstery.6 76. How to Wash Carpets1. Set up your
VAX as described on page 5.2. Switch ON.3. Switch on the power
washing button.4. Turnthesuction powertothewash settingorhigher,
dependingonthe carpet pile (Fig/6.1).5. To allow water to ow
through the Fibreow wash head, ensure that the rocker switch
(A)ispositionedtowardsthebackofthe wash head (Fig/6.2).6.
Withthesolutionowing,washasection ofcarpetapprox3metresx3metresby
pushingthewashheadbackwardsand forwards over the area.7.
Stopthesolutionowbymovingthe rocker switch (A) to the forward
position on the Fibreow wash head. This will prevent
waterow,allowingexcesswatertobe removedfromthesectionjustwashed
(Fig/6.3).8. Turn the pump washing button off and turn the suction
power to maximum.Gobackovertheareayouhavejust
washed.Thiswillnowextractexcess moisture from the carpet.9.Move to
the next area and repeat steps 3 to 8.10.
Whennomorewaterreachesthewash tool the pump will make a sound due
to sucking air.Rellthewaterreservoirwithwaterand
VAXCarpetcleaner.Emptytherecovery bucket when you rell the water
reservoir. The sound your VAX makes will change
andthesuctionwilldropiftherecovery bucketisover-full.Timetoemptyit!
(Fig/6.4)TipALWAYSTESTFORCOLOUR FASTNESSWITHSOMEUNDILUTED
CARPETCLEANERONAHIDDEN AREA FIRST.Startfromthecornerofaroomandwork
backwards towards the door.Ifyouarewashingverydirtycarpets,you may
have to wash them several times over
aperiodoftimetobringallthedirttothe
surface.Whenwashingstairs,placeyourVAX above the area you are
washing. ALWAYS ENSUREYOURVAXISSTABLE.The
castorsonyourVAXwillpulloff,givingit extra stability on stairs or
slopes. DO NOT PULL EXCESSIVELY ON THE
HOSE.Metalorwoodenfurniturelegsmaymark
awetcarpet.Waituntilthecarpetisdry
orplacealuminiumfoilunderthefeetof furniture.When washing deep pile
carpets, move the washingtoolinthesamedirectionasthe pile
lays.Dontallowchildrenoranimalsontothe carpet until it is dry.7.
How to Wash Upholstery1.SetupyourVAXasdescribedonpage
5,BUTdontusetheextendiblemetal
wand.2.Connecttheupholsterywashingtoolto
theshortbentendandwindtheexcess solution tube around a portion of
the hand grip.Connectthetubetotheupholstery washing tool
(Fig/7.1).3.Switch power button ON.4.Switch ON the pump washing
button.5.Turnthesuctionpowertothewash setting.6.To start the
solution ow, push the collar on the wash tool forward
(Fig/7.2).7.When you see water swirling in the washing tool you are
ready to start washing.8.Draw the washing tool backwards across the
upholstery. Cover a small area at a time. Dont push
thetoolbackwardsandforwardsasthis may stretch the fabric.6.Wrap
Solution Tube (A) to Hose (B) using Clipsprovided(C)
toholditinplace. Ensurethatthe solutiontubeis wrappedloosely
enoughtoallow the solution to ow freelythroughthe tube
(Fig/5.3).7.Fittheextendiblewandtothesuction hose.8.Fit the washing
tool andpushendof SolutionTubeonto connectingvalve ontheCarpet/
UpholsteryWash Tool
(Fig/5.4).TIPToachievecorrectlengthlaytubewithclips parallel to
hose and wand before attaching.9.Unclip the transparent tube on the
bottom of the motor unit. Ensure the tube is positioned
atthebottomofthe washingsolution (Fig/5.5).10. Fitthemotorunit
(makesurethe transparenttubeis nottrappedwhen youdothis)Secure
clipsonbothsideof motor.11. Locatethetube valve, push in rmly and
turn clockwise (Fig/5.6).YOUARENOW READYTOSTART
WASHINGTIPIfyourcarpethasbeenpreviouslywashed
withahighfoamingshampoo,pourVAX Defoamer into the recovery
bucket.VAX Defoamer is available through your VAX Stockist.