64568503 12 1 Configure Ip Bts Gsm via Cme Gui 1

1

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential

Security Level:

47pt

www.huawei.com

Configure IP BTS via

CME GUI

2

HUAWEI TECHNOLOGIES CO., LTD. Page 2Huawei Confidential

Right click the MBSC icon. Click ‘GSM BTS TOPOLOGY’.

3


Select the subrack no. and slot no. of the interface board to which the BTS will

connect. For example, it should be an FG2a working in IP mode.

Right click the interface board and then click ‘Add Site’.

4


Fill in the parameters according to the planned data.

BTS IP = BTS traffic IP; BSC IP = BSC IP that connect to this BTS

This project has some naming rules of BTS in the next page. Please obey them.

5


Rules for add BTS

6


Double click the new BTS icon

7


This step is just for the BTS that use APM30 cabinet.

Right click SRN 7, SN 0, and then click ‘Add PMU’.

8


Add boards according to the planned data.

This page is showing the APM30 cabinet. For Virtual cabinet, there is only Subrack

0.

9


Right click ‘TOPO’, click ‘Add RXUCHAIN’

10


Fill the parameters according to the planned data.

This project has some naming rules of RXUCHAIN in the next page. Please obey

them.

*For more than 1 RXUCHAIN, please repeat these two steps.

11


Configure all the BTSRXUCHAIN according to the BTS layout:

RXUCHAIN0: 0-0-6-0

RXUCHAIN0: 0-0-6-1

RXUCHAIN0: 0-0-6-2

Rules of RXUCHAIN

12


Right click RXUCHAIN on which the MRRU board will be.

Click ‘Add’ -> ‘Add MRRU’.

Add MRRU in RXUCHAIN

13


Fill the parameters according to the planned data.

Is Configure Check Threadhold = YES

Forward Bandwidth = 125Receive Bandwidth = 250

Power Bandwidth = CLASS0

This project has some naming rules of MRRU in the next 2 page. Please obey

them.

*For more than 1 MRRU board, please repeat these 2 steps.

14


Rules of MRRU (1)

Add RFU ADD BTSRXUBRD

Subrack No. = 60 + CPRIPort + (Position - 1)*6

Slot No. = 0

RXU Chain No. = CPRIPort

Position = 1 + cascadeNo.

15


Rules of MRRU (2)

16


MRRU/GRRU Second Receive Mode = DOUBLE_ANTENNA

Configure ‘Working Standard’ according to the planned area.

Adjust BTSRXUBP

17


Right click the BTS icon

Click ‘BTS Configuration Express’

Adjust BTS parameters

18


BTS Basic Attrbutes -> BTS -> BTS Description

BTS description = BTS name-siteLocation: 125GHI-Ghimpati

Configure BTS Description

19


Configure BTSESN according to the actual data.1. Click ‘+‘

2. Fill in the esn3. Click ‘√√√√‘

Configure BTSESN

20


Clock Protocol Type = ‘PTP’Clock Synchronizaton Mode = ‘INTERSYN’

Domain = ‘0’Configure IP address according to the planned area.

Configure BTSIPCLKPARA

21


‘BTS Transmission Link’ -> ‘IP BTS Route’Destination IP address is the ip segment of MBSC Port IP

Destination address mask is the mask of MBSC Port IP

Forward route address is the gateway of BTS traffic IP

Configure BTSIPRT

22


Single click the BTS iconRight click on the right panel, click ‘Add Cell’

Following shows the GCell configuration

23


Fill the parameters according to the planned data

24


Right click the cell

Click ‘Assign Frequency’

Following shows the Freq configuration

25


Select the frequency

Click ‘OK’

26


Right click the cell

Click ‘Add TRX’

Following shows the TRX configuration

27


Select the cell in the Cell List

Click ‘Add Binding(s)’

28


Fill the ‘Logical TRX No.’ according to the planned dataSelect TRX Board; select TRX Board Channel

For the BCCH Frq, please check the checkBox in front of the ‘Main BCCH’Click ‘Bind TRX’ to bind frequency to trx channel.

29


Set ‘Cell Hop Mode’ and ‘HSN’ according to the planned dataClick ‘Apply’

If you want to modify the maio, please double click on the little cell like the

blue circle.

30


Right click the cellClick ‘Cell Configuration Express’

Following shows the Cell configuration

31


Cell Attributes -> Basic GPRS Attributes of 2G CellConfigure ‘GPRS’, ‘NO’ and ‘Routing Area’ according to the planned data

32


Right click the trx

Click ‘TRX Configuration Express’

Following shows the TRX configuration

33


Power Type = 20W --Adjust this value according to the planned date

Shut Down Enabled = DISABLETCH Rate Adjust Allow = YES

Allow Dynamic Shutdown TRX = NO

Configure GTRXDEV

34


Set Channel Type to ‘PDTCH’ of Channel No. 6 of the Main BCCH TRX--According to the planned data

Configure GTRXCHAN

35


Transport -> MBSC -> GSM -> GB -> PTP BVC

Configure PTP BVC according to the planned data

Add PTP BVC

36


Transport -> MBSC -> GSM -> Abis -> Adjacent Node

Add adjnode according to the planned dataAdjacent Node Name = BTS Name

Add AdjNode

37


Transport -> MBSC -> GSM -> Abis -> Adjacent Node Mapping

Gold user TRMMAP index = 43Factor table index =20

Add AdjMap

38


Transport -> MBSC -> GSM -> Abis -> IP Path

Add IP path according to the planned data

Add IP Path

39


Transport -> MBSC -> GSM -> Abis -> IP Route

Fill the Subrack No. and Slot No. according to the planned data.Destination IP address is the ip segment of BTS traffic IP

Destination address mask is the mask of BTS traffic IP

Forward route address is the gateway of BSC port IP

Add IP Route

40


Export MML Script

41


The MML folder

Click the link. You can open the folder contains the MML script.

42

Thank youwww.huawei.com

64568503 12 1 Configure Ip Bts Gsm via Cme Gui 1

Documents

planned datahuawei

ip segment

planned area

planned data

trx configuration

huawei technologies

configure

add mrru