Sink screw M2.5X12 Head_plate_base Screw M3X16 Hub Jam Nut M3 Hub_root 600/700 Size AS350 Scale Rotor Head Instruction Manual Introduction Scale 600 size AS350 rotor head is the design of Double Cats team. It is for the 10mm diameter main shaft, 50/60 class RC model heli-copters with CCPM mode. This head is made by CNC. It provides your scale mode AS350 the best detail with flying stability. It's the best choice for your AS350 scale fuselage. Assembly Section Hub Assembly Push the thrust bearing 5X10X4 into the bearing holder Push the bearing 6X10X3 to the coper bearing bracket, and then the washer 6X9.6X0.5 Then assemble them together Mount the bearing holders to the hub Assemble the hub_root and head_plate_base to the hub
4
Embed
600/700 Size AS350 Scale Rotor Head Instruction Manual ... scale rotor head for 600&700 size... · 600/700 Size AS350 Scale Rotor Head Instruction Manual Introduction. Scale 600 size
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Sink screw M2.5X12
Head_plate_baseScrew M3X16
Hub
Jam Nut M3Hub_root
600/700 Size AS350 Scale Rotor Head Instruction Manual
Introduction Scale 600 size AS350 rotor head is the design of DoubleCats team. It is for the 10mm diameter main shaft, 50/60class RC model heli-copters with CCPM mode.
This head is made by CNC. It provides your scale modeAS350 the best detail with flying stability. It's the bestchoice for your AS350 scale fuselage.
Assembly SectionHub Assembly
Push the thrust bearing 5X10X4 into the bearing holder
Push the bearing 6X10X3 to the coper bearing bracket, and then
the washer 6X9.6X0.5
Then assemble them together
Mount the bearing holders to the hub
Assemble the hub_root and head_plate_base to the hub
Rubber_O_ring
Washer_5X7X1 Bearing 6X10X3
Feather_Shaft
Screw M2.5X10
Grip Board
Front baring holder
Screw M2.5X10
Screw M2.5X10Screw M2.5X8
Grip Arm
Mount Grips to Hub
Grip Assembly
Insert the coper feather_shaft, washer and rubber_O_ring to the tip of the hub
Mount the bearing 6X10X3 on the feather_shaft
Up side Down side
Screw M4X6
Screw M2X6
Screw M2.5X12
Swash plate up part
Joint ball bearing
Swash plate handle
Bearing 30X37X4
Screw M3X5
Swash plate down part
Follower base Screw M2X6
Follower arm
Screw M3X8 Bearing 2X5X2.5
Follower fork
Metal Link head D2M2
Head Disc Assembly
Swash Plate Assembly
Follower Assembly
Assemble the rotor disc to hub by a screw M4X6
Screw M2X14
Screw M2X14
Jam nut M2
Install on the Main Shaft
Phase Adjustment
1. Install the swash plate, follower and hub on the main shaft, using 4pcs
screws M2X14 and 4pcs jam nut M2 to connect the linkages and follower to
the swash plate. 2.Using 3pcs screws
M2X14 and 3pcs washer to connect linkage to grip
arms. 3.Insert the screw M3X20 through the
hole of main shaft and lock it with a jam nut M3.
90°
1. Adjust the follower, make sure the linkage on the position of swash plate
lead the center line of grip by 90 degrees.
2. Tighten the screw M3X8 on the follower base to lock the phase.