600 Intivo Space Larder Unit Assembly Components Ref. No. Item Quantity Ref. No. Item Quantity Tools Required Assembly Instructions 1 3 5 151999 152401 4 152418 4 152402 2 150101 20 3.5x12mm 150202 8 4x12mm 4x15mm 150201 16 154085 14 154004 14 154082 12 150199 4 4.5x45mm 4 154027 A B C D E B B 150308 4 150309 4 154047 2 154068 4 152162 6 Intivo Space Unit Caution: Some pieces of hardware could be hazardous to small children. Keep all these items out of reach and do not leave children unattended in the assembly area. Please read these instructions carefully before proceeding. Refer to the Guide to Receiving and Installing your Kitchen for further information. Note: Due to variation in wall conditions no screws are supplied for fixing the units to the wall. If in doubt consult an expert. Assemble the unit on a clean solid work surface. Important: Installation should be carried out exactly according to the manufacturer’s instructions otherwise a safety risk can occur if incorrectly installed. Warning: Assess the suitability of the wall/ceiling to ensure that the fastening devices will withstand the forces generated. In order to prevent falling down this product must be used with the wall attachment devices provided. In the interest of continuing improvements we reserve the right to amend or adjust the specifications without prior notice. Errors and omissions excepted. Every effort has been made to ensure that this product leaves the factory in perfect condition. In the unlikely event that an item is damaged or incorrect, please contact the customer services department. FM 665131 5mm Drill G-Clamp (pair) Medium Crosshead Screwdriver Hammer Spirit Level Bradawl Tape Measure Large Flathead Screwdriver 8mm Tall Intivo Space Unit F 1 2 3 Holes to be drilled 5mm in diameter and 12mm deep. Holes to be drilled 8mm in diameter and 12mm deep. Holes to be drilled 5mm in diameter and 12mm deep. NOTE: Only required on side panel that will have the door hinged to it. NOTE: Before assembly can be being, a number of additional holes must be drilled into each side panel. See diagrams for drilling positions, and key for hole dimensions. 1 37mm 115mm 339mm 37mm 101mm 389mm 421mm 57mm 397mm 738mm 1037mm 1280mm 1372mm 1404mm 266mm 298mm 605mm 948mm 980mm 1 1 2 2 3 3 1470mm 1 1 1 1 1 3 3 3 3 3 1 1 1 1 1 37mm 115mm 339mm 57mm 397mm 738mm 1037mm 1280mm 266mm 298mm 605mm 1 1 1 1 1 3 3 3 1 1 1 1 1 Top of Panel Standard Height Units, right side shown only. Mirror for left hand side panel. Top of Panel Tall Height Units, right side shown only. Mirror for left hand side panel. A A 35mm 152183 6 151500 2 154084 2 G A Important Information - True Handleless Kitchens Installers: See Note Above TH Note: If fitting a “True Handleless” kitchen, some components will differ to those shown in this instruction and will also be packaged separately. Please refer to your True Handleless guide to Receiving for further details on the different components and difference in installation. TH TH Modification required at this stage, see True Handleless guide for further details.
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
600 Intivo Space Larder Unit AssemblyComponents
Ref. No. Item Quantity Ref. No. Item Quantity
Tools Required Assembly Instructions1 3
5151999
152401 4
152418 4
152402 2
150101 203.5x12mm
150202 84x12mm
4x15mm150201 16
154085 14
154004 14
154082 12
15019944.5x45mm
4154027
A
B
C
D
EB
B
150308 4
150309 4
154047 2
154068 4
152162 6
Intivo Space Unit
Caution: Some pieces of hardware could be hazardous to small children. Keep all these items out of reach and do not leave children unattended in the assembly area.Please read these instructions carefully before proceeding. Refer to the Guide to Receiving and Installing your Kitchen for further information.Note: Due to variation in wall conditions no screws are supplied for fixing the units to the wall. If in doubt consult an expert. Assemble the unit on a clean solid work surface. Important: Installation should be carried out exactly according to the manufacturer’s instructions otherwise a safety risk can occur if incorrectly installed.Warning: Assess the suitability of the wall/ceiling to ensure that the fastening devices will withstand the forces generated. In order to prevent falling down this product must be used with the wall attachment devices provided.
In the interest of continuing improvements we reserve the right to amend or adjust the specifications without prior notice. Errors and omissions excepted.Every effort has been made to ensure that this product leaves the factory in perfect condition. In the unlikely event that an item is damaged or incorrect, please contact the customer services department.
FM 665131
5mm
DrillG-Clamp(pair)
Medium Crosshead Screwdriver Hammer
Spirit Level Bradawl
Tape MeasureLarge Flathead Screwdriver
8mm
Tall Intivo Space Unit
F
123
Holes to be drilled 5mm in diameter and 12mm deep.
Holes to be drilled 8mm in diameter and 12mm deep.Holes to be drilled 5mm in diameter and 12mm deep. NOTE: Only required on side panel that will have the door hinged to it.
NOTE: Before assembly can be being, a number of additional holes must be drilled into each side panel. See diagrams for drilling positions, and key for hole dimensions.
1
37m
m
115m
m
339m
m
37m
m
101m
m
389m
m
421m
m
57mm
397mm
738mm
1037mm
1280mm
1372mm1404mm
266mm298mm
605mm
948mm980mm
11 2 2
33
1470mm
1
1
1
1
1
33
3
33
1
1
1
1
1
37m
m
115m
m
339m
m
57mm
397mm
738mm
1037mm
1280mm
266mm298mm
605mm
1
1
1
1
1
3
33
1
1
1
1
1
Top of Panel
Standard Height Units, right side shown only. Mirror for left hand side panel.
Top of PanelTall Height Units, right side shown only. Mirror for left hand side panel.
A A
35mm
152183 6
151500 2
154084 2
GA
Important Information - True Handleless Kitchens Installers: See Note Above TH
Note: If fitting a “True Handleless” kitchen, some components will differ to those shown in this instruction and will also be packaged separately. Please refer to your True Handleless guide to Receiving for further details on the different components and difference in installation.
TH
TH Modification required at this stage, see True Handleless guide for further details.
4 7
115m
m
339m
m
57mm
397mm
738mm
1037mm
1280mm
115m
m
339m
m
57mm
397mm
738mm
1037mm
1280mm
Top of Panel
Standard Height Units, right side shown only. Mirror for left hand side panel.
Top of PanelTall Height Units, right side shown only. Mirror for left hand side panel.
6 4 6 4
6 4 6 4
6 4 6 4
6 4 6 4
6 4 6 4
6 4 6 4
7Drawer runner
7Drawer runner
7Drawer runner
7Drawer runner
7Drawer runner
7Drawer runner
7Drawer runner
7Drawer runner
7Drawer runner
7Drawer runner
66
12154004
4
4
154082 12
3.5 x 16mm x2x4
Fit as third screw
Front 1 x 'L'; 1 x 'R'
Drawer Runner7
NOTE: Fixings are supplied in with the drawers.
8 9
88
154085 14
8
8
8
8
B
8
8
8
8
B
8
8
8
8
B
9
A
A B
B
B
9
Start Locked
Do Not Over Tighten9
9
9
9
9
9
9
9
9
9
9
154084 2
5
5
6
6
5
5
8
8
G
10
9
G
10
9
TH Modification required at this stage, see True Handleless guide for further details.
TH Modification required at this stage, see True Handleless guide for further details.
15 1611 14
17 18 20
21 23
Installation Instructions
4150199
12
66mm 4
14
150202
154047 2
F
D
E13
66mm 4150202
154068 4
4
13
150101
Note: Countersunk screw goes into back panels D and F.
13
4152418
16
4152401 150201 16
15
140m
m
15
15 15
1515
16
16
16
16
15
14
12
12
1211
11
11
13
13
1212
13
14
14
280mm
23.5mm
619mm
Top of Larger Fascia
35mm
NOTE: Before attaching hinges, two hinge holes must be created on the larger of rthe two fascias at the positions indicated. Hinge holes are 35mm in diameter and 13mm in depth. Once the hinge hole is drilled, a hinge can be held in place and the screw guide holes created using a bradawl.
17
17
20
20
150101
152402
4
2
18
4150308 150309 4
5mm
18
19
19
Appropriate to wall type(Not supplied) 2
==
19
19
18
18
18
18
20
20
150101 12
22
23
23
5151999
Note: Do not over tighten screws or use a power screwdriver.
21
22
22
22
22
22
22
2223
23
23
23
23
TH Modification required at this stage, see True Handleless guide for further details.
29
24 26 27 28
Ref. 170859 (01)
24
2151500
24
25
4154027
25
24
24
C26
25
25
25
25
A 28B28 28
C27
27
28
C
A 28
B28
27
27
27
27
27
Attach drawer fascias as per instructions provided with drawers then insert into unit.
29
29
29
29
29
Related Documents
