Installation Instructions QUIKTUNE ® DROP-AWAY 2000RG For your convenience, an Installation DVD is also included. FIG. 1 Mounting the Arrow Holder Pad 1. Apply at room temperature. 2. Use the enclosed alcohol wipe to clean shelf. Allow shelf to dry. 3. Mathews centershot on Legacy, Icon, LX, Ovation and Outback bows is 13/16 inch. Remove the adhesive backing and apply the arrow holder on the shelf with the center of the "v" centered at 13/16 inch and one edge of the arrow holder even with the back edge of the bow shelf (Fig. 1). 4. Firmly press the arrow holder down. The pressure sensitive adhesive develops full strength in 24 hours. 5. Trim excess off the front of the holder as needed (Fig. 2). Mounting the rest Right & Left Handed Bows (Right Hand Shown) 1. If the roller guard is the short model and looks like Fig. 3, mount the rest using the 5/16 x 24 cap screw in the number 1 position (Fig. 3A). 2. If the roller guard is a long model and looks like Fig. 4 or Fig. 4A, mount the rest using the 5/16 x 24 cap screw in the number 2 position (Fig. 4B). FIG. 2 TRIMMED FRONT OF ARROW HOLDER 51-230 (REV 1) FIG. 3 FIG. 3A TWO HOLES Setting Centershot 1. Loosen the lift arm lock screw (Fig. 5) and allow the lift arm to swing down toward the bow handle. The lift arm position will be set after centershot and prong height. 2. The QuikTune Drop-Away 2000RG has been preset at the factory to Mathews recommended centershot - 13/16” (Fig. 6). 3. If the rest has been moved horizontally from the factory setting, loosen the horizontal/vertical lock screw on the bottom of the bracket (Fig. 5). 4. Use a ruler to move the horizontal centershot back to 13/16”. FIG. 4 FIG. 4A FIG. 4B FIG. 5 LIFT ARM LIFT ARM LOCK SCREW FIG. 6 13/16” THREE HOLES FOUR HOLES HORIZONTAL/VERTICAL LOCK SCREW FIG. 7 FIG. 8 FIG. 9 FIG. 10 LAUNCHER POSITION LOCK SCREW PLUNGER HOLE COVERED BY ARROW 90° BOTTOM OF PLUNGER HOLE SHOWS HORIZONTAL/VERTICAL LOCK SCREW 13/16” Page 2 Arm hangs down Page 3 Page 1 90° Setting the Nock Point and Arrow Height 1. Loosen the launcher position lock screw (Fig. 7). 2. Turn the knob toward the up arrow until the rest prongs move to the upright position. (Fig. 8). 3. Tighten the launcher position lock screw. 4. Loosen the horizontal/vertical lock screw on the bottom of the bracket (Fig.7). 5. Loosely (not completely clamped) set a nock point on the string. 6. Nock an arrow on the string. 7. Simultaneously rotate the brass barrel shaft assembly and adjust the nock point on the string so that the arrow is square when resting on the raised prongs. For carbon or small diameter arrows the arrow shaft should equally cover the plunger hole (Fig.9). With larger diameter arrows e.g. 2315, the very bottom of the plunger hole should show beneath the arrow shaft (Fig. 10). 8. Tighten the horizontal/vertical lock screw on the bottom of the bracket (Fig. 7). 9. Completely clamp the nock point. THE REST IS STILL IN THE RAISED POSITION and the lift arm is still loose and hanging down. EXTREMELY IMPORTANT: DO NOT USE METAL “D” NOCKS WITH THE QUIKTUNE DROP-AWAY 2000RG ON THE MATHEWS LX BOW. Due to the LX Model’s 6-5/8” brace height, use of Ultra-Nok or metal “D” type nocks will impact the QuikTune Drop-Away 2000RG’s Lift Arm and cause it to break. INSTRUCTION INSERT 6/12/06 2:20 PM Page 1