A-22 APEM www.apem.com 5000 series Toggle switches Distinctive features A THE WIDEST RANGE IN MINIATURE SWITCHES ❑ 17 actuators including toggles, paddle levers and locking levers in different lengths. ❑ 5 contact materials from dry circuit to 6A 125VAC and high inrush up to 120A 2 ms. ❑ 8 functions including maintained and momentary versions. ❑ 1 to 4 pole configurations. ❑ 12 terminal types including 9 for PC board mounting. Other types include quick-connect and wire-wrap. ❑ 6 bushing styles from 6 (.236) plain to 11,9 (15/32) threaded. ❑ 3 types of finish including military black. ❑ 4 approvals (UL - CSA - VDE - CECC) and 3 listings. ❑ 4 types of sealing for terminal or front panel requirements. ❑ Numerous accessories available for actuator and bushing options.
22
Embed
5000 series - Farnell · A-22 APEM 5000 series Toggle switches Distinctive features A THE WIDEST RANGE IN MINIATURE SWITCHES 17 actuators including toggles, paddle levers and locking
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
A-22 APEM www.apem.com
5000 seriesToggle switchesDistinctive features
A
THE WIDEST RANGE IN MINIATURE SWITCHES
17 actuators including toggles, paddle levers and locking levers in different lengths.
5 contact materials from dry circuit to 6A 125VAC and high inrush up to 120A 2 ms.
8 functions including maintained and momentary versions.
1 to 4 pole configurations.
12 terminal types including 9 for PC board mounting.Other types include quick-connect and wire-wrap.
6 bushing styles from 6 (.236) plain to 11,9 (15/32) threaded.
A : silverAD : silver, gold platedCD : brass, gold platedX814 : for peak currrents, see section G.
• Terminal seal : epoxy• Paddles : UL94HB polyamide• Lever caps : vinyl
ELECTRICAL SPECIFICATIONS
• Current/voltage rating with resistive load :
Contact Maximum Minimum Level*
Silver (A) 3A 250VAC - 6A 125VAC - 4A 30VDC 50mA 10VDC III and IV
Silver, 3A 250VAC - 6A 125 VAC - 4A 30VDC 10mA 50mV I to IVgold plated (AD) Gold plating withstands up to 100mA 30VDC 10µA 5V
Brass, 0,4 VA at 20VAC or DC 10mA 50mV I and IIgold plated (CD) 10µA 5V
• For inductive, lamp or capacitive load, consult factory. * For details, see Technical Information, end of catalogue.• Initial contact resistance : 10 mΩ max.• Insulation resistance : 1.000 MΩ min. at 500VDC• Dielectric strength :
1.000 Vrms 50 Hz min. between terminals1.500 Vrms 50 Hz min. between poles1.500 Vrms 50 Hz min. between terminals and frame
• Contact bounce : 2 ms max.• Electrical life at full load :
50.000 cycles for single and double pole40.000 cycles for 3 pole30.000 cycles for 4 pole
• Low level or mechanical life : 100.000 cycles
GENERAL SPECIFICATIONS
• Torque : 1,25 Nm (.922 Ft.lb) max. applied to nut• Panel thickness : 2,5 mm (.098) with 2 nuts - 4 mm (.157) with 1 nut• Operating temperature : -40°C to +85°C
AGENCY APPROVALS/PREFERENTIAL LISTS
For VDE, refer to 55000 series.
QPL (Europe only)MUAHAGNATO
Availability : consult factory for details of approved models.
Marking : to order switches marked UL, CSA or CECC, complete appropriatebox of ordering format.Preferential lists do not appear on the switches.
CECC 96201-007
EN 61058-1
A-24 APEM www.apem.com
5000 seriesToggle switchesOverview
A
5
SERIES
Terminals and bushing
0 Straight PC terminals, 5,08 (.200) terminal spacing, with Ø 6,35 (1/4) threaded bushing
1 Straight PC or quick-connect terminals, 4,70 (.185) terminal spacing, with Ø 6(.236) threaded bushing.
2 Straight PC terminals, 4,70 (.185) terminalspacing, right angle, quick-connect or wire wrap terminals, with 6,35 (1/4)threaded bushing
3 Straight PC terminals, 4 (.157) terminal spacing, with Ø 6 (.236) threaded bushing
4 Straight PC terminals, 4 (.157) terminal spacing or right angle terminals , withØ 6,35 (1/4) threaded bushing
5 Solder lug terminals, with Ø 6 (.236)threaded bushing.
6 Solder lug terminals, with Ø 6,35 (1/4) or Ø 11,9 (15/32) threaded bushing.
7 Solder lug terminals, with Ø 6,35 (1/4) flatted bushing.
9 Straight PC or quick-connect terminals,with Ø 6,35 (1/4) flatted bushing, 4,70 (.185) terminal spacing.
Number of poles
3 Single pole4 Double pole5 Three pole6 Four pole
Electrical functions
6 ON - ON9 ON OFF ON7 MOM OFF MOM8 ON OFF MOM2 ON - MOM
4 ON ON ONON ON MOM MOM ON MOM
Function 4Must not have blank in"connections" box.. Must not have blank in"momentary" box.
Connections forfunction 4
TH StandardCT ReversedSee wiring diagrams end ofsection B.. For functions 4, 4-1R, 4-2R.Leave blank for all otherfunctions.
Momentary forfunction 4
1R ON ON MOM2R MOM ON MOM
Leave blank for otherfunctions.
Terminals
Blank Solder lugs or straight PC depending on model
M Solder lugs with Ø 11,9 (15/32) bushing (5600 switches)
ABOUT THIS SERIESOn the following pages, you will find successively :- model structure of switches with threaded bushing - model structure of switches with plain bushing- options in the same order as in above chart
Dimensions : first dimensions are in mm while inches are shown as bracketted numbers.
NOTICE : please note that not all combinations of above numbers are available.Refer to the following pages for further information.
APEM www.apem.com A-25
5000 seriesToggle switches
Overview
A
Sealing boots are available. They are presented in section H.
Mounting accessories : standard hardware supplied with all models with Ø 6,35 (1/4) or Ø 6 (.236) threaded bushing :2 hex nuts 8 mm (.314) across flats, 1 locking ring and 1 lockwasher.Standard and special hardware available are presented in section I.
Packaging unit : 25 pieces or 50 pieces depending on models.
Finish
Blank Bright chrome finishG Matt black finish on
bushing, actuator andhardware.
Fluorescent tip
Blank None0.38 White fluorescent
tip to lever
Available with matt blackfinish (G) only.
Special options
Blank No special requirement
X408 Front panel sealing by two O-rings
X404 Horizontal right angle with reduced overall dimensions
Other : specific bushingheight, PC terminal length,finish, ratings, etc... Seefollowing pages.
• Terminal spacing 5,08 mm (.200)• Epoxy sealed terminals standard• 1and 2 pole configurations• Can also be used as extended PCB terminals
*Function 4 : SP in DP case - specify CT or TH connections, see end of catalogue.
III II I2-3 1-2
5236MIWR ON - ON5239MIWR ON OFF ON5237MIWR MOM OFF MOM5238MIWR ON OFF MOM5232MIWR ON - MOM
III II I2-3 1-25-6 4-5
5246MIWR ON - ON5249MIWR ON OFF ON5247MIWR MOM OFF MOM5248MIWR ON OFF MOM5242MIWR ON - MOM5244 MIWR* ON ON ON5244 1R MIWR* ON ON MOM5244 2R MIWR* MOM ON MOM
MODELSTRUCTURE
PANEL CUT-OUT
With K With X408Standard sealing option sealing option
• Pin spacing 3,81 mm (.150)• 1, 2, 3 and 4 pole configurations
III II I2-3 1-2
5236WW ON - ON5239WW ON OFF ON5237WW MOM OFF MOM5238WW** ON OFF MOM5232WW** ON - MOM
III II I2-3 1-25-6 4-5
5246WW ON - ON5249WW ON OFF ON5247WW MOM OFF MOM5248WW** ON OFF MOM5242WW** ON - MOM5244WW* ON ON ON5244WW 1R* ON ON MOM5244WW 2R* MOM ON MOM
III II I2-3 1-25-6 4-58-9 7-8
5256WW ON - ON5259WW ON OFF ON5257WW MOM OFF MOM5258WW** ON OFF MOM5252WW** ON - MOM
MODELSTRUCTURE
Shown with standard lever (-13)
* and ** : see notes next page.
(.500) (.150)
(.531) (.236) (.433)
24˚
(.11
8 D
IA)
(.24
6 D
IA)
(.04
3)
(.222)
(.275)
(.200)
(.039)
(.15
0)(.
500)
(.200)
(.062 DIA)
(.301)
I
II
III
3.81
12.7
0
1.10
Ø3.
00
Ø6.
25
13.50 6.00 11.00 7.00
0.80
3.8112.705.655.08
1.00
Ø1.60
5.08
3.00
(.11
8)(.
519)
13.2
0
3
2
1
13.2
0(.
519)
5.65 12.70 3.81(.222) (.150)(.500)
Ø6.
25
Ø3.
00
(.24
6 D
IA)
(.11
8 D
IA)
11.006.0013.50(.433)(.236)(.531)
24˚0.80
(.301)
(.472)
5.08(.200)
Ø1.60
12.7
03.
81
(.062 DIA)
(.50
0)(.
150)
(.04
3)1.
10
(.18
7)
12.00
I
II
III
4.75
(.11
8)3.
00
6
5
4
3
2
1
5.08(.039)
(.200)
1.00
(.187)4.75
(.11
8 D
IA)
(.24
6 D
IA)
Ø3.
00
Ø6.
25
(.515)13.10
(.500) (.150)3.8112.70
(.283)
4.75
(.18
7)
1.10
(.04
3)
(.649)
(.15
0)(.
500)
3.81
12.7
0
III
II
I
24˚
7.20
16.50
(.03
1)0.
80
3.00
13.2
0(.
118)
(.51
9)
1.00(.039)
(.200)5.08
9
8
7
3
2
1
(.200)5.08
(.062 DIA)Ø1.60
4.75(.187)
(.492)6.00
(.236)12.50
APEM www.apem.com A-41
5000 seriesToggle switches - plain bushing
Right angle terminals - vertical : 5200WW - 5400WW
A
Four poleIII II I2-3 1-25-6 4-58-9 7-811-12 10-11
5266WW ON - ON5269WW ON OFF ON5267WW MOM OFF MOM5268WW** ON OFF MOM5262WW** ON - MOM5264WW* ON ON ON5264WW 1R* ON ON MOM5264WW 2R* MOM ON MOM
* Function 4 : SP in DP case, DP in 4P case - specify CT or TH connections, see end of catalogue.** Functions 2 and 8 : reversed connection available, consult factory.
PCB MOUNTING
5400WW models
• Pin spacing 2,54 mm (.100)• 1, 2, 3 and 4 pole configurations
Diagram as per 5200WW model
For model structure numbers, referto 5200WW models and replace 2 with 4.
Single pole Double pole5236Y7 B 5246Y7 B ON - ON5239Y7 B 5249Y7 B ON OFF ON5237Y7 B 5247Y7 B MOM OFF MOM5238Y7 B 5248Y7 B ON OFF MOM5232Y7 B 5242Y7 B ON - MOM
5244Y7 B* ON ON ON5244Y7 1R B* ON ON MOM5244Y7 2R B* MOM ON MOM
* Function 4 : SP in DP case - specify CT or TH connections, see end of catalogue.
III II I2-3 1-25-6 4-5
Single pole Double pole5236Y6 B 5246Y6 B ON - ON5239Y6 B 5249Y6 B ON OFF ON5237Y6 B 5247Y6 B MOM OFF MOM5238Y6 B 5248Y6 B ON OFF MOM5232Y6 B 5242Y6 B ON - MOM
5244Y6 B* ON ON ON5244Y6 1R B* ON ON MOM5244Y6 2R B* MOM ON MOM
III II I2-3 1-25-6 4-5
Single pole Double pole5236Y4 B 5246Y4 B ON - ON5239Y4 B 5249Y4 B ON OFF ON5237Y4 B 5247Y4 B MOM OFF MOM5238Y4 B 5248Y4 B ON OFF MOM5232Y4 B 5242Y4 B ON - MOM
5244Y4 B* ON ON ON5244Y4 1R B* ON ON MOM5244Y4 2R B* MOM ON MOM