43 CCNA (200-120) Quick notes before exam ~ Sysnet Notes

8/10/2019 43 CCNA (200-120) Quick notes before exam ~ Sysnet Notes

1/16

12/2/2014 CCNA (200-120) Quick notes before exam ~ Sysnet Notes

http://sysnetnotes.blogspot.com/2013/10/ccna-200-120-quick-notes-before-exam.html

Home > Cisco> Routing > Switching > VMware CMD Prompt Tips More>

CCNA (200-120) Quick notes before examby Shabeer ibm

I prepared this notes after passing my CCNA 200-120.This last minute quick

notes are only intended to refresh your knowledge. Make sure you know

everything mentioned here before attending the CCNA 200-120 exam.For

complete and detailed CCNA notes click here

Points to Remember

By default router can break up broadcast domains.You need vlans in switches to

break broadcast domains

Both router and switch can break up collision domains

Routingoccur in internet layer in DOD TCP/IP reference model

PPP perform in layer 2

FTP belongs to Application layer

When Global command that is set once and affects the entire router

LCP PPP sub protocol negotiates authentication options

PPP and DSL are valid WAN connectivity methods

Rapid Spanning Tree Protocol, an enhancement to Spanning Tree Protocol is

used to prevent loops

When using the term frame we can easily recognize it belongs to the Data

Link layer

SYSNET NOTES

MicroSoft | Cisco | VMware | Networking Notes| Tips| Troubleshooting

NOV 2014 ) UNE PILULE MINCEUR CONTROVERSE CONQUIT LA FRANCE VIE SAINE)

Search
http://shabeeribm.tk/http://www.linkedin.com/in/shabeeribmhttp://www.facebook.com/sysnetnoteshttps://twitter.com/shabeeribmhttp://sysnetnotes.blogspot.com/p/vmware.htmlhttp://sysnetnotes.blogspot.com/p/vmware.htmlhttp://sysnetnotes.blogspot.in/search/label/cmd%20prompthttp://sysnetnotes.blogspot.com/http://sysnetnotes.blogspot.com/http://sysnetnotes.blogspot.in/search/label/cmd%20prompthttp://www.linkedin.com/in/shabeeribmhttp://sysnetnotes.blogspot.in/p/home.htmlhttps://twitter.com/shabeeribmhttp://sysnetnotes.blogspot.com/p/vmware.htmlhttp://adstrckr.net/tracker/base.php?c=3768&key=2b7127199e77d113593d087a5b9e3d39&subid=unepilule_[eng_website_id]_[eng_sub_id]http://sysnetnotes.blogspot.in/search/label/cmd%20prompthttp://shabeeribm.tk/http://www.facebook.com/sysnetnotes


2/16


http://sysnetnotes.blogspot.com/2013/10/ccna-200-120-quick-notes-before-exam.html 2

When using the term Packet we can easily recognize it belongs to the Network

layer

Show version command reveals the last method used to powercycle a router

show ip interfacecommand is used to verify which interfaces are affected by

the ACL

Both routers must use the same password for CHAP to authentication

Basic notes

To check the connectivity between a host and a destination (through some networks)

we can use both tracert and ping commands. But the difference between these 2

commands is the tracert command can display a list of near-side router interfaces

in the path between the source and the destination. The traceroute command has

the same function of the tracert command but it is used on Cisco routersonly, not

on a PC

When powered on, the router first checksits hardware via Power-On Self Test

(POST). Then it checks the configuration register to identify where to load the IOS

image from. In the output above we learn that the Configuration register value is

02102 so the router will try to boot the system image from Flash memory first.

The last known good router will try to inform you that the destination cannot be

reached (with a Destination Unreachable message type) so from that information

you can learn how far your packets can travel to and where the problem is.

Each interface on a router must be in a different network. If two interfaces are in the

same network, the router will not accept it and show error when the administrator

assigns it.

When no startup configuration file is found in NVRAM, the System Configuration

Dialog will appear to ask if we want to enter the initial configuration dialog or not.

Ping command can be used from a PC to verify the connectivity between hosts that

connect through a switch in the same LAN

Organizational Unique Identifier (OUI)is the first 24 bits of a MAC address for a

network device, which indicates the specific vendor for that device as assigned by

the Institute of Electrical and Electronics Engineers, Incorporated (IEEE). This

identifier uniquely identifies a vendor, manufacturer, or an organization.


3/16



The Maximum Transmission Unit (MTU) defines the maximum Layer 3 packet (in

bytes) that the layer can pass onwards.

Modern Ethernet networks built with switches and full-duplex connections no

longer utilize CSMA/CD. CSMA/CD is only used in old switches

The Network layeris responsible for network addressing and routing through the

internetwork. So a ping fails, you may have an issue with the Network layer.Packets

are created when the network layer adds Layer 3 addresses and control information

to a segment.

The transport layerdivides a data stream into segments and may add reliability

and flow control information.

Application layerin the OSI reference model is responsible for determining the

availability of the receiving program and checking to see if enough resources exist

for that communication

When upgrading new version of the IOS we need to copy the IOS to the Flash so first

we have to check if the Flash has enough memory or not. Also running the new IOS

may require more RAM than the older one so we should check the available RAM

too. We can check both with the show version command.

When will devices transmit in a Ethernet network ?

Ethernet network is a shared environment so all devices have the right to access to

the medium. If more than one device transmits simultaneously, the signals collide

and cannot reach the destination. If a device detects another device is sending, it will

wait for a specified amount of time before attempting to transmit. When there is no

traffic detected, a device will transmit its message. While this transmission is

occurring, the device continues to listen for traffic or collisions on the LAN. After themessage is sent, the device returns to its default listening mode.

Two purposes does the Ethernet protocol use physical addresses

Physical addresses or MAC addresses are used to identify devices at layer 2

To allow communication between different devices on the same network

The following locations can be configured as a source for the IOS image:


4/16



Flash (the default location)

TFTP server

ROM (used if no other source is found)

What is the difference between a CSU/DSU and a modem?

A CSU/DSU converts digital signals from a router to a leased line; a modem

converts digital signals from a router to a phone line.

Router boot process:

The Power-On Self Test (POST) checks the routers hardware. When the POST

completes successfully, the System OK LED indicator comes on.

The router checks the configuration register to identify where to load the IOS image

from. A setting of 02102 means that the router will use information in the startup-

config file to locate the IOS image. If the startup-config file is missing or does not

specify a location, it will check the following locations for the IOS image:1. Flash (the default location)

2. TFTP server

3. ROM (used if no other source is found)

Basic IOS notes

service password-encryptioncommand, all the (current and future) passwords are

encrypted. This command is primarily useful for keeping unauthorized individuals

from viewing your password in your configuration file.

How to secure the virtual terminal interfaces on a router?

Configure a virtual terminal password and login process.

Enter an access list and apply it to the virtual terminal interfaces using the

access-class command.

Commands

Router(config)# service password-encryptioncommand encrypts all plaintextpasswords.

Router (config-if)# ppp authentication chap papcommand is used to enable CHAP

authentication with PAP as the fallback method on a serial interface

Router#show vlancommand only displays access ports, the trunk ports are not

showed in this command


5/16



"Show frame-relay lmi command allows you to verify the encapsulation type

(CISCO or IETF) for a frame relay link

show ip ospf database - command is used to display the collection of OSPF link

states

Below lists popular modes in Cisco switch/router:

Router> User mode

Router# Privileged mode

Router(config)# Configuration mode

Router(config-if)# Interface level (within configuration mode)

Router(config-router)# Routing engine level (within configuration mode)

Router(config-line)# Line level (vty, tty, async) within configuration mode

Trunking Notes:

Valid Vlan Trunk Modes

Desirable

Auto

ON

Dynamic Trunking Protocol (DTP) is a Cisco proprietary protocol for negotiating

trunking on a link between two devices and for negotiating the type of trunking

encapsulation (802.1Q) to be used.

IEEE 802.1Q is the networking standard that supports Virtual LANs (VLANs) on an

Ethernet network. It is a protocol that allows VLANs to communicate with one

another using a router. 802.1Q trunks support tagged and untagged frames.If a

switch receives untagged frames on a trunk port, it believes that frame is a part ofthe native VLAN. Also, frames from a native VLAN are not tagged when exiting the

switch via a trunk port.

Three elements must be used when you configure a router interface for vlan

trunking?

one IP network or subnetwork for each subinterface

subinterface encapsulation identifiers that match vlan tags


6/16



one subinterface per vlan

Cisco switches support two trunking protocols 802.1q & ISL. 802.1q is an open

standard and is thus compatible between most vendors equipment while Inter-

Switch Link (ISL) is Cisco proprietary.

Click herefor detailed VTP notes

STP Notes

Only non-root bridge can have root port.

The path cost to the root bridge is the most important value to determine which port

will become the root port on each non-root switch. In particular, the port with lowest

cost to the root bridge will become root port (on non-root switch).

Per VLAN Spanning Tree (PVST) maintains a spanning tree instance for each VLAN

configured in the network. It means a switch can be the root bridge of a VLAN while

another switch can be the root bridge of other VLANs in a common topology. For

example, Switch 1 can be the root bridge for Voice data while Switch 2 can be the

root bridge for Video data. If designed correctly, it can optimize the network traffic.

If we connect two switches via 2 or more links and do not enable STP on theseswitches then a loop (which creates multiple copies of the same unicast frame) will

occur. It is an example of an improperly implemented redundant topology.

PVST+ is based on IEEE802.1D Spanning Tree Protocol (STP). But PVST+ has only 3

port states (discarding, learning and forwarding) while STP has 5 port states

(blocking, listening, learning, forwarding and disabled). So discarding is a new port

state in PVST+.

RSTP only has 3 port states that are discarding, learning and forwarding. When RSTP

has converged there are only 2 port states left: discarding and forwarding

A BPDU is superior than another if it has:

1. A lower Root Bridge ID

2. A lower path cost to the Root

3. A lower Sending Bridge ID
http://sysnetnotes.blogspot.com/2013/06/vlan-trunking-protocol-vtp-explained.html


7/16



4. A lower Sending Port ID

Click herefor detailed STP Notes

ACL Notes

The standard access lists are ranged from 1 to 99 and from 1300 to 1999

We can have only 1 access list per protocol, per direction and per interface. It

means:

We can not have 2 inbound access lists on an interface

We can have 1 inbound and 1 outbound access list on an interface

We can use a dynamic access list to authenticate a remote user with a specific

username and password. The authentication process is done by the router or a

central access server such as a TACACS+ or RADIUS server.

Click herefor detailed ACL notes

NAT Notes

With static NAT, translations exist in the NAT translation table as soon as you

configure static NAT command(s), and they remain in the translation table until you

delete the static NAT command(s).Because static NAT translations are always present

in the NAT table so outside hosts can initiate the connection without being dropped

With dynamic NAT, translations do not exist in the NAT table until the router

receives traffic that requires translation. Dynamic translations have a timeout

period after which they are purged from the translation table.

By not reveal the internal Ip addresses, NAT adds some security to the inside

network

By allocating specific public IP addresses to inside hosts, NAT eliminates the need to

re-address the inside hosts

VLAN Notes

A native VLAN mismatch error will appear by CDP if there is a native VLAN

mismatch on an 802.1Q link. VLAN mismatch can cause traffic from one vlan to

leak into another vlan.
http://sysnetnotes.blogspot.com/2013/07/spanning-tree-protocol-stp-ieee-8021d.htmlhttp://sysnetnotes.blogspot.com/2013/08/access-list-notes-numbered-and-named-acl.html


8/16



VLANs allow to group users by function, not by location or geography

VLANs help minimize the incorrect configuration of VLANs so it enhances the

security of the network

VLANs increase the number of broadcast domains while decreasing the size of the

broadcast domains which increase the utilization of the links. It is also a bigadvantage of VLAN

Advantages of VLANs

VLANs establish broadcast domains in switched networks.

VLANs allow access to network services based on department, not physical

location.

VLANs can greatly simplify adding, moving, or changing hosts on the network.

For 802.1q encapsulation, the native VLAN must matched at both side; otherwise the

link will not work.

VLAN 1 is the default VLAN on Cisco switch. It always exists and can not be added,

modified or removed.

VLANs 1002-1005 are default VLANs for FDDI & Token Ring and they cant be deleted

or used for Ethernet.

Click here for detailed VLAN notes

Frame Relay Notes

To configure subinterface for Frame Relay, first we have to remove the IP address

from the physical interface and choose a Frame Relay encapsulation.

The PVC STATUS displays the status of the PVC. The DCE device creates and sends the

report to the DTE devices. There are 4 statuses:ACTIVE: the PVC is operational and can transmit data

INACTIVE: the connection from the local router to the switch is working, but the

connection to the remote router is not available

DELETED:the PVC is not present and no LMI information is being received from the

Frame Relay switch

STATIC:the Local Management Interface (LMI) mechanism on the interface is

disabled (by using the no keepalive command). This status is rarely seen so it is
http://sysnetnotes.blogspot.com/2013/05/vlan-explained-with-interview-questions.html


9/16



ignored in some books.

DLCI: DLCIstands for Data Link Connection Identifier. DLCI values are used on

Frame Relay interfaces to distinguish between different virtual circuits. DLCIs have

local significance because the identifier references the point between the local

router and the local Frame Relay switch to which the DLCI is connected.

Committed information rate (CIR):The minimum guaranteed data transfer rate

agreed to by the Frame Relay switch. Frames that are sent in excess of the CIR are

marked as discard eligible (DE) which means they can be dropped if the congestion

occurs within the Frame Relay network.

Note: In the Frame Relay frame format, there is a bit called Discard eligible (DE) bit

that is used to identify frames that are first to be dropped when the CIR is exceeded.

Local Management Interface (LMI)is a signalling standard protocol used betweenyour router (DTE) and the first Frame Relay switch

Inverse ARPis a technique by which dynamic mappings are constructed in a

network, allowing a device such as a router to locate the logical network address and

associate it with a permanent virtual circuit (PVC).

IP Routing Notes

When one route is advertised by more than one routing protocol, the router willchoose to use the routing protocol which has lowest Administrative Distance.

Routers decrement the TTL by 1 every time they forward a packet; if a router

decrements the TTL to 0, it throws away the packet. This prevents packets from

rotating forever

Remember these rules:

The IP addresses (of source and destination) of a packet never change during the

transportation through the network. For example if PC-A wants to send a packet toPC-Z then the source and destination IP addresses of the packet will be the IP

addresses of PC-A and PC-Z no matter how many devices they go through.

The MAC addresses, conversely, will change while passing the devices. The source

MAC address is the address of the last sender and the destination MAC address is the

address of the next device.

The simple syntax of static route:


10/16



ip route destination-network-address subnet-mask {next-hop-IP-address | exit-

interface}

Explanation

destination-network-address:destination network address of the remote network

subnet mask: subnet mask of the destination network

next-hop-IP-address:the IP address of the receiving interface on the next-hoprouter

exit-interface: the local interface of this router where the packets will go out

DHCP Notes

Network or sub network IP address and broadcast address should never be

assignable to hosts. When try to assign these addresses to hosts, you will receive an

error message saying that they cant be assignable.

An address conflict occurs when two hosts use the same IP address. During address

assignment, DHCP checks for conflicts using ping and gratuitous ARP. If a conflict is

detected, the address is removed from the pool. The address will not be assigned

until the administrator resolves the conflict.

OSPF Notes

The highest IP address of all loopback interfaces will be chosen as Router-ID

110 is the default administrative distance of OSPF

The default number of equal-cost paths that can be placed into the routing of a Cisco

OSPF router is 4. We can change this default value by using maximum-paths

command:

Router(config-router)#maximum-paths 2

Note:Cisco routers support up to 6 equal-cost paths

Characteristics of a link-state routing protocolProvides common view of entire topology

Calculates shortest path

Utilizes event-triggered updates

Describe the routing protocol OSPF

It supports VLSM.

It confines network instability to one area of the network.

View and Download complete CCNA and CCNP PDF Notes for Just $ 5 Click here
http://sysnetnotes.blogspot.in/p/home.html


11/16



It allows extensive control of routing updates

Hierarchical design of OSPF (basically means that you can separate the larger

internetwork into smaller internetworks called areas) helps us create a network

with all features listed like (decrease routing overhead, speed up convergence;

confine network instability to single areas of the network).

Hello packets and LSAs from other routers are used by router running a link-state

protocol to build and maintain its topological database

To form an adjacency (become neighbour), router A & B must have the same Hello

interval, Dead interval and AREA number.

Click here for detailed OSPF notes

EIGRP Notes

Make sure you know how to configure and troubleshoot EIGRP.

AD of EIGRP Internal Route is 90

AD of EIGRP external Route is 170

AD of EIGRP summary Route is 5

Passive Interface:In EIGRP (and OSPF) the passive interface command stops

sending outgoing hello packets, hence the router cannot form any neighbor

relationship via the passive interface. This behavior stops both outgoing and

incoming routing updates

Feasible successor is a route whose Advertised Distance is less than the Feasible

Distance of the current best path. A feasible successor is a backup route, which is not

stored in the routing table but stored in the topology table.

EIGRP stub advertises summary and directly connected routes. EIGRP stub routing

feature improves network stability, reduce resources utilization and simplifies stub

router configuration. Any neighbor that receives a packet informing it of the stub

status will not query the stub router for any routes.EIGRP stub configuration

command increases scalability by limiting the

EIGRP query range

Active State:When a route (current successor) goes down, the router first checks its

topology table for a feasible successor but it cant find one. So it goes active on the
http://sysnetnotes.blogspot.in/search/label/OSPFmailto:[email protected]


12/16



that route to find a new successor by sending queries out to its neighbors requesting

a path to the lost route.

Click herefor detailed EIGRP Notes

Security Notes

We only enable PortFast feature on access ports (ports connected to end stations).

But if someone does not know he can accidentally plug that port to another switch

and a loop may occur when BPDUs are being transmitted and received on these

ports.

With BPDU Guard, when a PortFast receives a BPDU, it will be shut down to prevent

a loop

We can verify whether port security has been configured by using the show

running-config or show port-security interface for more detail

Port security is only used on access port (which connects to hosts) so we need to set

that port to access mode, then we need to specify the maximum number of hosts

which are allowed to connect to this port.

Note: If we want to allow a fixed MAC address to connect, use the switchport port-

security mac-address command.

One of the most widely deployed network security technologies today is IPsec over

VPNs. It provides high levels of security through encryption and authentication,

protecting data from unauthorized access.

IPV6 Notes

Features of the IPv6 protocol

Autoconfiguration

No broadcasts

Plug-and-play

A single interface may be assigned multiple IPV6 addresses of any type.

Every IPV6 interface contains at least one loopback address.

With IPv6, devices can build a link-local address automatically. But notice this

address is only used for communications within the local subnetwork, routers do not

forward these addresses.

Below is the list of common kinds of IPv6 addresses:
http://sysnetnotes.blogspot.in/search/label/EIGRP


13/16



Loopback address ::1

Link-local address FE80::/10

Site-local address FEC0::/10

Global address 2000::/3

Multicast address FF00::/8

Click herefor Detailed IPv6 notes

SNMP protocol can cause overload on a CPU of a managed device

TRAP and INFORM are the alert message generated by SNMP agents

In a GLBP network, AVG is responsible for the arp request

Components of SNMPMIB

SNMP Manager

SNMP Agent

3 features are added in SNMPv3 over SNMPv2

Message Integrity

Authentication

Encryption

Popular destinations for syslog messages to be saved

The logging buffer .RAM

The console terminal

Syslog server

The benefit of using Netflow

Network, Application & User MonitoringSecurity Analysis

Accounting/Billing

3 things that the Netflow uses to consider the traffic to be in a same flow

IP address

Port numbers

L3 protocol type
http://sysnetnotes.blogspot.in/2013/09/ccnp-notes-ipv6-quick-notes.html


14/16



Related articles

Gateway Redundancy Protocols (HSRP)

Configuring Basic OSPF

OSPF Authentication

Cisco Discovery Protocol (CDP)

Quick reminder about HSRP

EIGRP Configuration and Troubleshooting commands

Top 10 'show' Commands

5 Comments:

REPLY

REPLY

Tony

October 4, 2013 at 12:29 PM

Hi Shabeer,

you are an absolute life saver for the little details that i missed studying for 640-802. Iscored 801/1000 :(

Now that i am in the process of studying for and sitting the 200-120 exam i wanted toknow what the process for getting a copy of the notes from your blog was?

Shabeer Ibm

October 4, 2013 at 12:33 PM

You can download Complete PDF via paypal

REPLY

Anonymous

December 13, 2013 at 8:14 AM

Thanks shabeer this notes really helped me to pass CCNA in first attempt
http://sysnetnotes.blogspot.com/2013/08/eigrp-configuration-and-troubleshooting.htmlhttp://sysnetnotes.blogspot.com/2013/09/configuring-basic-ospf.htmlhttp://sysnetnotes.blogspot.com/2013/09/gateway-redundancy-protocols-hsrp-n.htmlhttp://sysnetnotes.blogspot.com/2013/09/ospf-authentication.htmlhttp://sysnetnotes.blogspot.com/2013/10/ccna-200-120-quick-notes-before-exam.html?showComment=1386902676881#c1408438551622925061http://www.blogger.com/profile/14800622378615115709http://sysnetnotes.blogspot.com/2013/09/quick-reminder-about-hsrp.htmlhttp://sysnetnotes.blogspot.com/2013/08/cisco-discovery-protocol-cdp.htmlhttp://sysnetnotes.blogspot.com/2013/10/ccna-200-120-quick-notes-before-exam.html?showComment=1380869973041#c559506405525227356http://sysnetnotes.blogspot.com/2013/10/ccna-200-120-quick-notes-before-exam.html?showComment=1380870197334#c6035413460816789007http://sysnetnotes.blogspot.com/2013/10/top-10-show-commands.html


15/16



REPLY

Enter your comment...

Comment as: Google Accou

Publish

Preview

Links To This Post

Create a Link

N E X T P O S T : Short Note on Etherchannel

P R E V I O U S P O S T : Top 10 'show' Commands

REPLY

Faarah Adam

November 23, 2014 at 5:36 AM

Hi Shabeer, I bought the notes and downloaded the Zip file, but when I tried to extractthem I get asked for a password. please help.

Faarah Adam ([email protected])

Shabeer Ibm

November 24, 2014 at 8:29 PM

I already forwarded the updated PDF notes to your email.Hope my notes helps inyour studies

V I S I T OR S LA B EL S

BasicsC C N A A N D C C N P

NOTES FOR JUST $5
http://sysnetnotes.blogspot.com/2013/10/ccna-200-120-quick-notes-before-exam.html?showComment=1416841193565#c7818972936887921347http://sysnetnotes.blogspot.com/search/label/Batch%20filehttp://sysnetnotes.blogspot.com/2013/10/top-10-show-commands.htmlhttp://sysnetnotes.blogspot.com/search/label/Access%20listhttp://www.blogger.com/profile/14800622378615115709http://sysnetnotes.blogspot.com/search/label/AAAhttp://sysnetnotes.blogspot.com/2013/10/ccna-200-120-quick-notes-before-exam.html?showComment=1416701202125#c5491279721715035453http://sysnetnotes.blogspot.com/search/label/basichttp://www.blogger.com/profile/04811006006055286204http://www.blogger.com/blog-this.ghttp://sysnetnotes.blogspot.com/search/label/BGPhttp://sysnetnotes.blogspot.com/2013/11/short-note-on-etherchannel.htmlhttp://sysnetnotes.blogspot.com/search/label/ARPhttp://sysnetnotes.blogspot.com/search/label/Basics


16/16
http://sysnetnotes.blogspot.com/search/label/Static%20routinghttp://sysnetnotes.blogspot.com/search/label/Switchinghttp://sysnetnotes.blogspot.com/search/label/LABhttp://sysnetnotes.blogspot.com/search/label/FAQhttp://sysnetnotes.blogspot.com/search/label/lotus%20noteshttp://sysnetnotes.blogspot.com/search/label/softwarehttp://sysnetnotes.blogspot.com/search/label/Securityhttp://sysnetnotes.blogspot.com/search/label/Interviewhttp://sysnetnotes.blogspot.com/search/label/short%20noteshttp://sysnetnotes.blogspot.com/search/label/windowshttp://sysnetnotes.blogspot.com/search/label/internet%20explorerhttp://sysnetnotes.blogspot.com/http://sysnetnotes.blogspot.com/search/label/Etherchannelhttp://sysnetnotes.blogspot.com/search/label/network%20monitoringhttp://sysnetnotes.blogspot.com/search/label/IPv6http://sysnetnotes.blogspot.com/search/label/HSRPhttp://sysnetnotes.blogspot.com/search/label/cmd%20prompthttp://sysnetnotes.blogspot.com/search/label/kasperskyhttp://sysnetnotes.blogspot.com/search/label/Troubleshootinghttp://sysnetnotes.blogspot.com/search/label/CCNAhttp://sysnetnotes.blogspot.com/search/label/CCNP%20Switchinghttp://sysnetnotes.blogspot.com/search/label/Commandshttp://sysnetnotes.blogspot.com/search/label/DHCPhttp://sysnetnotes.blogspot.com/search/label/VTPhttp://sysnetnotes.blogspot.com/search/label/MPLShttp://sysnetnotes.blogspot.com/search/label/wirelesshttp://sysnetnotes.blogspot.com/search/label/Firewallhttp://sysnetnotes.blogspot.com/search/label/STPhttp://shabeeribm.fetchapp.com/sell/xeelesohhttp://sysnetnotes.blogspot.com/search/label/VLANhttp://sysnetnotes.blogspot.com/search/label/tipshttp://sysnetnotes.blogspot.com/search/label/Configurationhttp://sysnetnotes.blogspot.com/search/label/OSPFhttp://sysnetnotes.blogspot.com/search/label/MCPhttp://sysnetnotes.blogspot.com/search/label/Routinghttp://sysnetnotes.blogspot.com/search/label/errorhttp://sysnetnotes.blogspot.com/search/label/EIGRPhttp://sysnetnotes.blogspot.com/search/label/MSThttp://sysnetnotes.blogspot.com/search/label/CCNP%20Routinghttp://sysnetnotes.blogspot.com/search/label/Private%20VLANhttp://sysnetnotes.blogspot.com/search/label/FortiGate

43 CCNA (200-120) Quick notes before exam ~ Sysnet Notes

Documents