3hh 10116 Aaaa Tczza 01 7360 Isam Product Information r4_3_x

Alcatel-Lucent 7360INTELLIGENT SERVICES ACCESS MANAGER FX | RELEASE 4.3P R O D U C T I N F O R M A T I O N

3HH-10116-AAAA-TCZZA Edition 01 Released

Alcatel-Lucent ProprietaryThis document contains proprietary information of Alcatel-Lucent and is not to be disclosedor used except in accordance with applicable agreements.Copyright 2011 © Alcatel-Lucent. All rights reserved.

When printed by Alcatel-Lucent, this document is printed on recycled paper.

Alcatel-Lucent assumes no responsibility for the accuracy of the information presented, which is subject to change without notice.

Alcatel, Lucent and the Alcatel-Lucent logo are registered trademarks of Alcatel-Lucent. All other trademarks are the property of their respective owners.

Copyright 2011 Alcatel-Lucent.All rights reserved.

Disclaimers

Alcatel-Lucent products are intended for commercial uses. Without the appropriate network design engineering, they must not be sold, licensed or otherwise distributed for use in any hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct life-support machines, or weapons systems, in which the failure of products could lead directly to death, personal injury, or severe physical or environmental damage. The customer hereby agrees that the use, sale, license or other distribution of the products for any such application without the prior written consent of Alcatel-Lucent, shall be at the customer's sole risk. The customer hereby agrees to defend and hold Alcatel-Lucent harmless from any claims for loss, cost, damage, expense or liability that may arise out of or in connection with the use, sale, license or other distribution of the products in such applications.

This document may contain information regarding the use and installation of non-Alcatel-Lucent products. Please note that this information is provided as a courtesy to assist you. While Alcatel-Lucent tries to ensure that this information accurately reflects information provided by the supplier, please refer to the materials provided with any non-Alcatel-Lucent product and contact the supplier for confirmation. Alcatel-Lucent assumes no responsibility or liability for incorrect or incomplete information provided about non-Alcatel-Lucent products.

However, this does not constitute a representation or warranty. The warranties provided for Alcatel-Lucent products, if any, are set forth in contractual documentation entered into by Alcatel-Lucent and its customers.

This document was originally written in English. If there is any conflict or inconsistency between the English version and any other version of a document, the English version shall prevail.

Alcatel-Lucent 7360 ISAM FX R4.3 July 2011 iii3HH-10116-AAAA-TCZZA Edition 01 Released Product Information

Preface

This preface provides general information about the documentation set for the 7360 Intelligent Services Access Manager FX (7360 ISAM FX).

Scope

This documentation set provides information about safety, features and functionality, ordering, hardware installation and maintenance, CLI and TL1 commands, and software upgrade and migration procedures.

Audience

This documentation set is intended for planners, administrators, operators, and maintenance personnel involved in installing, upgrading, or maintaining the 7360 ISAM FX.

Prerequisite knowledge

The reader must be familiar with general telecommunications principles.

Safety information

For ETSI safety information, see the 7360 ISAM FX Safety Manual.

Preface

iv July 2011 Alcatel-Lucent 7360 ISAM FX R4.3Product Information Edition 01 Released 3HH-10116-AAAA-TCZZA

The following are examples of how special information is presented in this document.

Document conventions

The following conventions are used in this documentation set.

AcronymsSee the glossary included with the System Description for FD 100/320Gbps NT and FX NT for the expansion of acronyms used in this documentation set.

Release notes

Be sure to refer to the release notes (such as the Customer Release Notes or Emergency Fix Release Note) issued for software loads of the 7360 ISAM before you install or use the 7360 ISAM FX . The release notes provide important information about the software load.

Danger — Danger indicates that the described activity or situation may result in serious personal injury or death; for example, high voltage or electric shock hazards.

Warning — Warning indicates that the described activity or situation may, or will, cause equipment damage or serious performance problems.

Caution — Caution indicates that the described activity or situation may, or will, cause service interruption.

Note — A note provides information that is, or may be, of special interest.

Preface

Alcatel-Lucent 7360 ISAM FX R4.3 July 2011 v3HH-10116-AAAA-TCZZA Edition 01 Released Product Information

Documents

Table 1 lists the documents that make up the 7360 ISAM FX Release 4.3 documentation set.

Table 1 7360 ISAM FX Release 4.3 documentation set

Title Description Part number

Documentation CD

7360 ISAM FX CD CD containing all the documents in the 7360 ISAM FX documentation set (1)

3HH-10103-AAAA

General documentation

Product Information Provides general system information for the 7360 ISAM FX 3HH-10116-AAAA-TCZZA

System Description for FD 100/320Gbps NT and FX NT

Provides conceptual information for:

• the 7302 ISAM and the 7330 ISAM FTTN equipped with the 100Gpbs or the 320Gbps NT

• the 7360 ISAM FX equipped with an FX NT

3HH-09811-BAAA-TQZZA

Safety Manual Provides general safety guidelines when handling, installing, or operating the 7360 ISAM FX equipment

3HH-10126-AAAA-TCZZA

Hardware documentation

FX Hardware Installation Guide

Describes the hardware installation for the 7360 ISAM FX equipment

3HH-10127-AAAA-RJZZA

TL1 documentation

TL1 Commands and Messages for FD 100/320Gbps NT and FX NT

Describes the TL1 commands and messages for:



3HH-09857-BAAA-TCZZA

Operations and Maintenance Using TL1 for FD 100/320Gbps NT and FX NT

Provides task-oriented procedures using TL1 for operating and maintaining:




CLI documentation

CLI Commands for FD 100/320Gbps NT and FX NT

Describes the CLI commands for:



3HH-08079-DDAA-TCZZA

Operations and Maintenance Using CLI for FD 100/320Gbps NT and FX NT

Provides task-oriented procedures using CLI for operating and maintaining:




IHub System Basics, Management and OAM Guide for FD 100/320Gbps NT and FX NT

Describes the IHub system basics, system management and OAM (Operations and Maintenance)

3HH-10106-AAAA-TQZZA

IHub Interface Guide for FD 100/320Gbps NT and FX NT

Describes the IHub system interfaces 3HH-10107-AAAA-TQZZA

(1 of 2)

Preface

vi July 2011 Alcatel-Lucent 7360 ISAM FX R4.3Product Information Edition 01 Released 3HH-10116-AAAA-TCZZA

Note(1) Software documentation is not included on the 7360 ISAM documentation CD

IHub QoS Guide for FD 100/320Gbps NT and FX NT

Describes the IHub Quality of Service 3HH-10108-AAAA-TQZZA

IHub Router Configuration and Protocols Guide for FD 100/320Gbps NT and FX NT

Describes the IHub router configuration and router protocols 3HH-10110-AAAA-TQZZA

IHub Services Guide for FD 100/320Gbps NT and FX NT

Describes the IHub services 3HH-10109-AAAA-TQZZA

IHub MPLS Guide for FD 100/320Gbps NT and FX NT

Describes the IHub MPLS services 3HH-10111-AAAA-TQZZA

Software documentation(1)

Software Installation Guide Describes the software management of the 7302 ISAM, the 7330 ISAM FTTN, the 7356 ISAM FTTB and the 7360 ISAM FX equipment

3HH-07196-AAAA-RJZZA

Software Upgrade and Migration Application Procedures

Provides instructions for using the automated tools for upgrading and migrating the software for the 7302 ISAM, the 7330 ISAM FTTN, the 7356 ISAM FTTB and the 7360 ISAM FX

3HH-08277-AAAA-TCZZA

Title Description Part number

(2 of 2)

Contents

Preface iiiScope ............................................................................................... iiiAudience ............................................................................................... iiiPrerequisite knowledge ............................................................................... iiiSafety information..................................................................................... iiiDocument conventions ................................................................................ ivRelease notes........................................................................................... ivDocuments ...............................................................................................v

1 — System Overview 1-11.1 Introduction.............................................................................. 1-21.2 System Architecture .................................................................... 1-61.3 Network Management ................................................................. 1-171.4 Equipment Management .............................................................. 1-181.5 Board Capabilities and Dimensioning ............................................... 1-191.6 NT Redundancy Support............................................................... 1-251.7 CLEI Codes............................................................................... 1-26

2 — Subracks 2-12.1 Introduction.............................................................................. 2-22.2 General ................................................................................... 2-22.3 7360 ISAM FX Subracks ................................................................. 2-22.4 Supported Plug-in Units ................................................................ 2-62.5 Dummy Front Panels.................................................................... 2-7

3 — Physical Rack Equipment 3-13.1 General ................................................................................... 3-23.2 Universal Rack ........................................................................... 3-2

Alcatel-Lucent 7360 ISAM FX R4.3 July 2011 vii3HH-10116-AAAA-TCZZA Edition 01 Released Product Information

Contents

3.3 Side Plates ............................................................................... 3-53.4 Rack Doors ............................................................................... 3-63.5 Key Locks ................................................................................. 3-7

4 — Rack Configurations 4-14.1 General ................................................................................... 4-24.2 Rack Configurations..................................................................... 4-2

5 — SFP Optical Modules 5-15.1 Introduction.............................................................................. 5-25.2 SFP Optical Modules .................................................................... 5-2

A. Board Mnemonics A-1A.1 Board Mnemonics........................................................................ A-2

Index

viii July 2011 Alcatel-Lucent 7360 ISAM FX R4.3Product Information Edition 01 Released 3HH-10116-AAAA-TCZZA

Alcatel-Lucent 7360 ISAM FX R4.3 July 2011 1-13HH-10116-AAAA-TCZZA Edition 01 Released Product Information

1 — System Overview

1.1 Introduction 1-2

1.2 System Architecture 1-6

1.3 Network Management 1-17

1.4 Equipment Management 1-18

1.5 Board Capabilities and Dimensioning 1-19

1.6 NT Redundancy Support 1-25

1.7 CLEI Codes 1-26


1-2 July 2011 Alcatel-Lucent 7360 ISAM FX R4.3Product Information Edition 01 Released 3HH-10116-AAAA-TCZZA

1.1 Introduction

The 7360 ISAM FX is a frame based Multi Service Access Platform, offering high-density fiber connections for multimedia, high-speed internet access, voice and business services.

General Network Topology

Figure 1-1 shows the basic network topology.

Figure 1-1 General network topology

Note — Possible user interface types are not limited to the types shown on the figure.

xDSL ISAM

Video

FE/GE

FE/GE

IP Edge Router / BRAS

EMAN

EthernetSwitch NSP IP backbone

NSP IP backbone

NSP IP backbone

xDSLLT

EthLT

VoiceLT

GPONLT

xDSL

Ethernet

Voice

DS1/E1

Video

NT

ISAM shelf

ISAM

OMCIGPON

ISAM OLT

FE/GE/10GE

FE/GE/10GE

ONT/ONU

Ethernet

Voice

DS1/E1

EPONLT

OAMEPON

ONT/ONU

xDSL/Ethernet

Voice



User Side

At the user side, each 7360 ISAM FX shelf can terminate:

• Ethernet user interfaces• Passive Optical Network (PON) interfaces

It is possible to connect subtending DSLAMs to the FE/GE/10GE links at the user side in:

• cascading mode: a chain of 1 subtending ISAM per ISAM; see Figure 1-2• star mode: multiple subtending ISAMs per ISAM; see Figure 1-3• ring mode (except when there is a ring behind a Hub-ISAM); see Figure 1-4.

Figure 1-2 Cascading Topology

Figure 1-3 Star Topology

ISAMISAM

Cascading up to three levels

ISAM

Userinterfaces

k*FE/GE/10GEk*FE/GE/10GE

EMAN

Userinterfaces User

interfaces

ISAMISAM

ISAM

Userinterfaces

k*FE/GE/10GE

EMAN

k*FE/GE/10GE

Userinterfaces

Userinterfaces



Figure 1-4 Ring Topology

Network Side

At the network side, the 7360 ISAM terminates FE, GE, or 10GE links. The following configurations are possible:

• Connected to one or more Ethernet SwitchesThe Ethernet links can be connected to one or more Ethernet Switches. These Ethernet Switches forward the frames over the Ethernet based aggregation access network until they reach the IP Edge Router or BRAS of the corresponding Network Service Provider (NSP). At the IP Edge Router or BRAS, the frames enter the IP backbone of the NSP.

• More than one FE/GE/10GE link (link aggregation)In case of more than one link, Ethernet link aggregation is used.

• Directly connected to an IP Edge RouterThe 7360 ISAM FX can be connected directly to the IP Edge Router or BRAS. The Ethernet aggregation network is reduced to one or more parallel Ethernet links.

• Can also be connected to a Multi-protocol Label Switching (MPLS) network.

ISAM

k*FE/GE/10GE

ISAM

Userinterfaces

k*FE/GE/10GE

ISAM

EMANISAM

k*FE/GE/10GEUserinterfaces

Userinterfaces

Userinterfaces



Figure 1-5 Network Connections

Note — A link is a term which is used to refer to the physical layer of an interface of the 7360 ISAM FX, for example, an Ethernet link.

ISAMUserinterfaces

FE/GE

m x FE/GE/10GE

n x FE/GE/10GE

IP Edge Router /BRAS

EMAN

EthernetSwitch

NSP IP backbone

NSP IP backbone

NSP IP backbone

ISAMUserinterfaces

FE/GENSP IP backbone



1.2 System Architecture

Functional DecompositionThe ISAM is built as a typical multiplexer which can be equipped with the following main boards:

• a Network Termination (NT) board (optionally 1+1 redundant)• a NT Input/Output board (optional)• a set of Ethernet Line Termination (LT) boards implementing the user interfaces.• Gigabit Passive Optical Network (GPON) LT boards• Ethernet Passive Optical Network (EPON) LT boards

Figure 1-6 ISAM Decomposition

The ISAM’s management plane, control plane, and most of the data plane is realized on the NT board and on the LT boards.

Figure 1-7 ISAM System Decomposition

ISAM

NT

NTIO

LT

LT-applique

…

LTNT

iHub

System control

iHub control

Switch/Router IWF

Transport

Data plane

Control plane

LT-Control



FX NT Board

The FX NT board consist of an IHub subsystem and a System Control subsystem.

• The IHub subsystem has enhanced L2 functionality (VPLS based) and L3 functionality (VPRN based) and consists of a 10-Gigabit-Ethernet switch/router device, and IHub control software (SW).

• The System Control subsystem implements the management plane of the system (both the NT board and the LT boards) and part of the control plane (subscriber management in particular). The System Control consists of SW running on a powerful general purpose processor. It shares this processor with the IHub control SW (on a separate processor core).

Line Termination (LT) Boards

Line Termination (LT) boards are built from an InterWorking Function (IWF), a Transport subsystem and an LT-Control subsystem.

• The transport subsystem terminates the physical layer of the subscriber interfaces. It varies with the type of access technology used (Ethernet,...).

• The IWF processes the packets in the fast path. It is capable of handling frames at L2 (basically bridging) and L3 (basically IP forwarding), including sophisticated filtering and traffic management, all at the line rate of the transport medium.

• The LT-Control subsystem takes care of the slow path control plane and internal Operations And Maintenance applications.

GPON LT Boards

The GPON functionality of the ISAM extends the system boundaries via up to 128 Optical Network Terminations (ONTs) over a fiber plant that can reach 10s of kilometers out from the GPON LT boards located in an ISAM shelf.

These GPON LT boards provide the physical interfaces from the ISAM shelf towards the Customer Premises Equipment, that is, the ONTs.

EPON LT Boards

The EPON functionality of the ISAM extends the system boundaries via up to 64 Optical Network Terminations (ONTs) over a fiber plant that can reach 10s of kilometers out from the EPON LT boards located in an ISAM shelf.

These EPON LT boards provide the physical interfaces from the ISAM shelf towards the Customer Premises Equipment, that is, the ONTs.

Physical DecompositionFigure 1-8 shows the general functional architecture of the ISAM, from the viewpoint of its forwarding capabilities.



Figure 1-8 High-level ISAM Architecture

An ISAM shelf consists out of the following board types:

• NT board• LT boards

NT Board

Provisions are made to equip two NT boards in the shelf. These NT boards can act as an active / stand-by pair for all functions.

The following NT boards are supported in FX equipment:

• FANT-F (480 Gbps NT board):This NT board with integrated IHub subsystem provides the following links on the front panel:

• One electrical RJ45 interface:This port supports 10/100/1000Base-T

• Four 10GE SFPplus port:These ports can work both in 1 GE mode (with standard SFP optics) and in 10 GE mode (with SFPplus optics).

LT Boards

The LT boards consists of a IWF, the transport termination and the LT control.

The LT boards, also known as Line Interface Modules (LIMs), use a different interworking function between the user side and the Ethernet network side, depending on the board type. Table 1-1 shows the supported LT boards with their physical interface types, density (that is, number of lines per board) and Interworking function (IWF) capability.

Table 1-1 Supported LT Boards

LT Board PhysicalInterfaces

Overlay Density NT Interface IWF

NELT-B Ethernet - 36 10 GE L3 (2)

(1 of 2)

NT

NTIO

2 -

EPS

EMAN

IWF Transport

LTcontrol

n

Ethernet CPE

LT

Network links |Subtending links |

User links

Systemcontrol

IHubcontrol

IHubrouter GPON ONT

EPON ONT



Notes(1) L2: IWF function capability on Layer 2. For an overview of the IWF capabilities, refer to section 1.5(2) L3: IWF function capability on Layer 2 and Layer 3. For an overview of the IWF capabilities, refer

to section 1.5(3) Not all L3 features are supported in these ports, see Table 1-13

GFC Board

The General Facilities Card (GFC) provides connections for external power, circuit breakers for system protection, visual indications for power availability and collection and cascading of external alarms.

NTIO Board

The NTIO board plays the role of an applique to either the single NT board, or to both NT boards, depending on the NT redundancy configuration. It allows to decouple NT equipment protection from up-link protection in case of a redundant NT pair. In case the active NT fails, traffic on the NTIO external links will be switched automatically to and from the stand-by NT.

Table 1-2 shows the supported NT I/O boards.

Table 1-2 NT I/O Boards

NGLT-A GPON - 8 10 GE L3 (2)(3)

FPLT-A EPON - 8 10 GE L2(1)

Note — These boards are only used on the FX-8 and FX-4 subracks.

Board Interfaces

FNIO-B Eight additional external Ethernet interfaces:

• eight optical 100/1000Base-FX

Eight additional external Ethernet interfaces:

• four optical 100/1000Base-FX• four combo uplink ports, which can be configured to optical uplink ports (SFP ports,

100Base-FX, 1000Base-FX) or electrical uplink ports ( RJ45, 10/100/1000BASE-T)

LT Board PhysicalInterfaces

Overlay Density NT Interface IWF

(2 of 2)



Port mapping

The tables below list the port mapping for 7360 ISAM FX, that is, the mapping between the logical port numbers as used in the ISAM and the physical port numbers as visible on the equipment itself (frontplate numbering).

• Table 1-3 lists the different mapped items.• Table 1-4 lists the port mapping for the FANT-F board in a 7360 ISAM FX-16

subrack.• Table 1-5 lists the port mapping for the FANT-F board in a 7360 ISAM FX-16 in

dual NT + NTIO subrack mode for FNIO-B.• Table 1-6 lists the port mapping for the FANT-F board in a 7360 ISAM FX-8


dual NT + NTIO subrack mode for FNIO-B.• Table 1-8 lists the port mapping for the FANT-F board in a 7360 ISAM FX-4


dual NT + NTIO subrack mode for FNIO-B.

Table 1-3 Mapped Items

Table 1-4 FANT-F in 7360 ISAM FX-16

Item Description

Physical Port Number The physical switch device port number.

Logical Port Number The port number as denoted in the SNMP management interface

LT port number (index based)

For internal LT ports, the index of the LT in the main subrack that corresponds to this port (for local LTs only)

Faceplate port number For external ports, the manner in which this port is identified at the faceplate of the board.

Port state / configurability For NTIO ports, the manner in which this port can be configured:

• UP for uplinks/subtending/user links• DOWN for internal LT links

and

• FIXED for fixed configuration (UP or DOWN)• CONF for configurable configuration (UP or DOWN)

Physical PortNumber

Logical PortNumber

LT SlotNumber(indexbased)

FaceplatePortNumber

Interface

10 15 1

12 16 2

16 17 3

18 18 4

(1 of 2)



Table 1-5 FANT-F + FNIO-B in 7360 ISAM FX-16

32 19 5

34 20 6

41 21 7

43 22 8

45 23 9

37 24 10

22 25 11

8 26 12

39 27 13

28 28 14

20 29 15

14 30 16

2 5 1 (NT-A) RJ45

4 6 X1 (NT-A) SFP+

5 7 X2 (NT-A) SFP+

6 8 X3 (NT-A) SFP+

7 9 X4 (NT-A) SFP+

3 3 IEEE1588 (NT-A)

2 10 1 (NT-B) RJ45

4 11 X1 (NT-B) SFP+

5 12 X2 (NT-B) SFP+

6 13 X3 (NT-B) SFP+

7 14 X4 (NT-B) SFP+

3 4 IEEE1588 (NT-B)

Physical PortNumber

Logical PortNumber


FaceplatePortNumber

Interface

(2 of 2)

PhysicalPortNumber

Logical PortNumber


FaceplatePortNumber

Interface FNIO-B

FaceplatePortNumber

Port State /Configurability

10 15 1

12 16 2

16 17 3

18 18 4

(1 of 2)



32 19 5

34 20 6

41 21 7

43 22 8

45 23 9

37 24 10

22 25 11

8 26 12

39 27 13

28 28 14

20 29 15

14 30 16

47 31 as on NTIO SFP 1 (SFP) UP, FIXED




30 35 as on NTIO SFP or RJ45 5 (Combo) UP, FIXED




2 5 1 (NT-A) RJ45

4 6 X1 (NT-A) SFP+

5 7 X2 (NT-A) SFP+

6 8 X3 (NT-A) SFP+

7 9 X4 (NT-A) SFP+

3 3 IEEE1588 (NT-A)

2 10 1 (NT-B) RJ45

4 11 X1 (NT-B) SFP+

5 12 X2 (NT-B) SFP+

6 13 X3 (NT-B) SFP+

7 14 X4 (NT-B) SFP+

3 4 IEEE1588 (NT-B)

PhysicalPortNumber

Logical PortNumber


FaceplatePortNumber

Interface FNIO-B

FaceplatePortNumber


(2 of 2)





Physical PortNumber

Logical PortNumber


FaceplatePortNumber

Interface

59 15 1

47 16 2

28 17 3

8 18 4

51 19 5

36 20 6

24 21 7

16 22 8

2 5 1 (NT-A) RJ45

4 6 X1 (NT-A) SFP+

5 7 X2 (NT-A) SFP+

6 8 X3 (NT-A) SFP+

7 9 X4 (NT-A) SFP+

3 3 IEEE1588 (NT-A)

2 10 1 (NT-B) RJ45

4 11 X1 (NT-B) SFP+

5 12 X2 (NT-B) SFP+

6 13 X3 (NT-B) SFP+

7 14 X4 (NT-B) SFP+

3 4 IEEE1588 (NT-B)

PhysicalPortNumber

Logical PortNumber


FaceplatePortNumber

Interface FNIO-B

FaceplatePortNumber


59 15 1

47 16 2

28 17 3

8 18 4

51 19 5

36 20 6

(1 of 2)




24 21 7

16 22 8









2 5 1 (NT-A) RJ45

4 6 X1 (NT-A) SFP+

5 7 X2 (NT-A) SFP+

6 8 X3 (NT-A) SFP+

7 9 X4 (NT-A) SFP+

3 3 IEEE1588 (NT-A)

2 10 1 (NT-B) RJ45

4 11 X1 (NT-B) SFP+

5 12 X2 (NT-B) SFP+

6 13 X3 (NT-B) SFP+

7 14 X4 (NT-B) SFP+

3 4 IEEE1588 (NT-B)

PhysicalPortNumber

Logical PortNumber


FaceplatePortNumber

Interface FNIO-B

FaceplatePortNumber


(2 of 2)

Physical PortNumber

Logical PortNumber


FaceplatePortNumber

Interface

27 15 1

23 16 2

12 17 3

8 18 4

2 5 1 (NT-A) RJ45

4 6 X1 (NT-A) SFP+

(1 of 2)




5 7 X2 (NT-A) SFP+

6 8 X3 (NT-A) SFP+

7 9 X4 (NT-A) SFP+

3 3 IEEE1588 (NT-A)

2 10 1 (NT-B) RJ45

4 11 X1 (NT-B) SFP+

5 12 X2 (NT-B) SFP+

6 13 X3 (NT-B) SFP+

7 14 X4 (NT-B) SFP+

3 4 IEEE1588 (NT-B)

Physical PortNumber

Logical PortNumber


FaceplatePortNumber

Interface

(2 of 2)

PhysicalPortNumber

Logical PortNumber


FaceplatePortNumber

Interface FNIO-B

FaceplatePortNumber


27 15 1

23 16 2

12 17 3

8 18 4









2 5 1 (NT-A) RJ45

4 6 X1 (NT-A) SFP+

5 7 X2 (NT-A) SFP+

6 8 X3 (NT-A) SFP+

7 9 X4 (NT-A) SFP+

3 3 IEEE1588 (NT-A)

(1 of 2)



IHub

The IHub provides L2 bridging (based on VPLS) and IP routing (based on VPRN). It has at least 28 ports with a various specialization:

A number of ports are used to make a connection at 1 Gbps or at 2.5 Gbps or at 10 Gbps to an LT local in the shelf (one IHub link per LT). The actual connection speed depends on the LT capabilities; see Table 1-1.

The FE/GE ports, which are not used for connecting LT boards (local or remote), and the 10GE ports, are available as network interfaces, as interfaces to subtended DSLAM systems, or for connecting directly to users. These links serve network links, subtending links, or user links respectively.

Use of these ports is possible either through:

• Link interfaces which are physically located on an NTIO board, connected via bi-directional point-to-point high-speed tracks on the back-panel to both NT boards.These interfaces can also be used as electrical FE, electrical GE or optical GE, optical 10GE interfaces, for uplink, subtending or user links (depending on the NTIO board capabilities and software support). The NTIO board contains an NT equipment protection switch per external link interface.So link protection and NT equipment protection can be performed independently from each other for links terminated on the NTIO.

• Link interfaces that are physically located on the NT board itself, as electrical FE interfaces, electrical GE interfaces, optical GE interfaces, and optical 10 GE interfaces, for uplink, subtending or user links.

2 10 1 (NT-B) RJ45

4 11 X1 (NT-B) SFP+

5 12 X2 (NT-B) SFP+

6 13 X3 (NT-B) SFP+

7 14 X4 (NT-B) SFP+

3 4 IEEE1588 (NT-B)

PhysicalPortNumber

Logical PortNumber


FaceplatePortNumber

Interface FNIO-B

FaceplatePortNumber


(2 of 2)



1.3 Network Management

Figure 1-9 shows how the 7360 ISAM FX can be managed in a network.

Figure 1-9 7360 ISAM FX Network Management

The remote Craft Terminal (CT) uses TL1 commands or Command Line Interface (CLI) commands. TL1 is used for pre-provisioning of the NT board. CLI is used to manage both the xHub subsystem and the IACM.

Figure 1-10 shows the management topology for the 7360 ISAM FX.

Figure 1-10 7360 ISAM FX Management Topology

The NT Controller and the xHub subsystem each contain a separate SNMP agent. These can be managed via an Element Management Station (EMS), such as the Alcatel-Lucent 5520 AMS.

It is also possible to use local TL1 or CLI craft terminal on the NT board to manage the LTs.

LIM

LIM

LIM

EMAN

EMS CT

RS232

Network Ports

Remote CT

Management Flow to cascaded ISAM

ISAM

IACM

xHub

CLI (via Telnet)TL1 (via UDP-login)

ISAM

CLIagent

TL1agent

SNMPagent

RS232RS232 SSH TelnetUDPSNMPv2

orSNMPv3

Debugagent

SSH UDP

EMS(e.g. AMS 5520)

TL1Gateway

CLITerminal

TL1CT

CLICT

TL1Terminal

DebugTerminal

Telnet



An integrated CLI approach is implemented on the NT board using an CLI agent. This agent implements CLI commands for the NT Controller / LIMs and the xHub subsystem. However, there is no semantic integration.

Table 1-10 shows an overview of the involved managers.

Table 1-10 Manager Overview

1.4 Equipment Management

The NE equipment practice type does not have to be explicitly planned by the operator, but is auto-planned by the NT at startup, depending on the detected type. At the same time, the NT will autoplan the maximum number of racks supported by this equipment practice. The following ISAM type is defined:

• LNWW: Large New Equipment Practise Worldwide market (6 racks, 4 subracks per rack)

Subracks are automatically planned upon detection. The operator can control the administrative state of a subrack (lock/unlock).

The NE manages different types of boards. A complete overview of all supported board types in each type of subrack is given in the chapter “Subracks”. Board planning is supported for all types of boards, including the appliques. For LSMs, the operator can control the administrative state (lock/unlock).

Central Office Equipment managementCentral Office equipment only supports configurations consisting of a single rack/subrack.

ONT ManagementFor more information on the ONT management, see the System Description for FD 100/320Gbps NT and FX NT document.

Type Description

EMS Element Management System (EMS) based on SNMP. The Alcatel-Lucent WorkStation (5520 AMS) is commonly used.

CT Craft Terminal using TL1 commands or Command Line Interface (CLI) commands.

Note 1 — External OAM VLAN:

The IHub subsystem supports in-band management. This happens through a dedicated VLAN, which must be configured (if different than 4093) on both the IHub subsystem as on the NT.

Note 2 — VLAN 4094 and VLAN range 4088 and 4092 are reserved for internal use.



1.5 Board Capabilities and Dimensioning

This section provides an overview of:

• dimensioning information for the NT boards; see Table 1-11• SyncE support on NT boards and NTIO boards; see Table 1-12• the IWF capabilities of the LT boards per forwarding type; see Table 1-13• Ethernet frame size; see Table 1-14• dimensioning information of the LT boards per forwarding type; see Table 1-15• GPON-specific dimensioning; see Table 1-16• EPON-specific dimensioning; see Table 1-17

NT Board DimensioningTable 1-11 shows the dimensioning for the different NT board and their variants.

Table 1-11 NT Board Dimensioning

Note(1) A number of MAC addresses are always used by the system for internal purposes.(2) The same resource is shared for L2 filters and L3 filters. So, the maximum cannot be obtained for

both at the same time.

Description FANT-F AC

Throughput 480 Gbps

Maximum number of MAC addresses (FDB)(1)

128 k

Maximum number of IP interfaces 512

ARP table size 16 k

Maximum number of IP routes:

FIB

RIB

16 k

16 k

Maximum number of L2 filters 512(2)

Maximum number of L3 filters 512

Maximum number of VLAN 4 k

Maximum number of cross-connect

4 k

L2 frame size (in bytes) 480 Gbps

External interfaces 1 x El. GE

4 x 1/10 GE

BITS in/out ports 1/1

SyncE input/output 4/4



SyncE SupportTable 1-12 indicates the port applicability of the Synchronous Ethernet NTR functionality for clock extraction (in) and generation (out).

Table 1-12 Faceplate port applicability for Synchronous Ethernet

Board Port SyncE In Support SyncE Out Support

FANT-F X1 1GE and 10GE 1GE and 10GE

X2 1GE and 10GE 1GE and 10GE



FNIO-B 1 - 1GE

2 - 1GE

3 - 1GE

4 - 1GE

5 - 1GE

6 - 1GE

7 - 1GE

8 - 1GE



IWF CapabilitiesTable 1-13 provides an overview of the IWF capabilities of the LT boards. Refer to Table 1-1 for an overview of the supported LT boards.

Table 1-13 IWF Capabilities

Feature L3 L3GPON

L3EPON

NELT-B

UNI NNI

ATM AAL5 encapsulation type

LLC/SNAP bridged (IPoE and PPPoE) Y - - - -

LLC/SNAP routed (IPoA) Y - - - -

LLC/NLPid (PPPoA) Y - - - -

VC Mux Bridged (IPoE and PPPoE) Y - - - -

VC Mux Routed (IPoA) Y - - - -

VC Mux PPPoA (PPPoA) Y - - - -

Encapsulation autodetect

Autodetect IP (between LLC/SNAP bridged and routed) Y - - - -

Autodetect PPP (between LLC/SNAP bridged, VC Mux Bridged and LLC-NLPID, VC Mux PPPoA)

Y - - - -

Autodetect IP+PPP Y - - - -

Autodetect PPPoA (between LLC-NLPID and VC Mux PPPoA)

Y - - - -

Bridged Encapsulation Ethernet Packet formats

Reception of untagged packets Y Y - Y Y

Reception of combination of untagged and priority tagged packets

Y Y - Y Y

Reception of single tagged packets Y Y Y Y Y

Reception of combination of untagged, priority tagged, single tagged packets

Y Y - Y Y

Packet processing

Port Based Default VLAN for untagged / priority tagged (if applicable) packets

Y Y - Y Y

Port and Protocol Based default VLAN for untagged / priority tagged packets of the IpoE Protocols

Y Y - Y Y

Port and Protocol Based default VLAN for untagged / priority tagged packets of the PPPoE Protocols

Y Y - Y Y

Priority Bit Remarking and Mapping table for tagged / priority tagged packets

Y Y Y Y Y

L2 Forwarding

RB mode: Protocol Filter (set of Ethertypes) for upstream traffic in VLANs in (PPPoE and IpoE)

Y Y Y Y Y

RB mode Ethernet packet types: Ethernet II Encap on Ethernet

Y Y Y Y Y

(1 of 2)



Note(1) ARP relay only(2) Support policing on bridge port on L2

Ethernet Frame SizeTable 1-14 indicates the supported Ethernet frame size for the different line boards..

RB mode Ethernet packet types: LLC/SNAP on Ethernet Y Y Y Y Y

CC Mode: transparently pass all encapsulations (e.g. PPPoE and IpoE)

Y Y Y Y Y

CC Mode: Protocol Filter Y Y - Y -

CC Mode: IPoA to IPoE CC Y - - - -

VLAN stacking (S-VLAN CC and S-VLAN / C-VLAN CC) Y Y Y Y Y

VLAN stacking (S-VLAN / C-VLAN Residential Bridge) - - Y - Y

QoS-aware CC Y - - - -

L2 Forwarding user access protocols

ARP: enabling/disabling broadcast Y Y Y Y -

802.1X authentication Y Y - Y -

DHCP option 82 insertion Y Y Y Y -

PPPoE relay tag Y Y Y Y -

PPPoA-PPPoE relay Y - - - -

Multicast services Y Y Y Y -

L3 Forwarding

IPoE Y Y - Y -

IPoA Y Y - Y -

VLAN termination (at network side), forwarding at Layer 3

Y Y - Y Y

L3 Forwarding user access protocols

802.1X authentication Y - - Y -

ARP proxy user side for IPoE Y Y Y(1) Y -

DHCP relay Y - - Y -

QoS

CAC profile Y Y Y Y Y

Association of QOS profiles to ports Y(2) Y - Y Y

Association of QOS profiles to port-VLAN associations Y Y Y Y -

Feature L3 L3GPON

L3EPON

NELT-B

UNI NNI

(2 of 2)



Table 1-14 Ethernet Frame Size for different LT boards

Dimensioning of the LT BoardsTable 1-15 provides dimensioning information of the LT boards. Refer to Table 1-1 for an overview of the supported LT boards.

Table 1-15 Dimensioning Information

LT Board Encapsulation Frame Size (bytes)

P2P Eth NELT-B UNI (with FCS) 1976

NELT-B NNI (with FCS) 2048

OLT NGLT-A (with FCS) 2000

OLT FPLT-A (with FCS) 2000

Feature L3 L3GPON

L3EPON

NELT-B

UNI NNI

General

Maximum number of PONs - 8 8 - -

Maximum number of UNIs - 4096 4096 - -

Maximum number of FE ports per board - - - 36 36

Maximum number of GE ports per board - - - 36 36

Maximum number of UNI port type (FE) per board - - - 36 -

Maximum number of UNI port type (GE) per board - - - 36 -

Maximum number of NNI port type (FE) per board - - - - 36

Maximum number of NNI port type (GE) per board - - - - 36

Maximum number of CC VLAN 768 11520 7680 4608 4608

Maximum number of RB VLAN 768 1296 1296 1296 1296

Maximum number of VLAN per PVC 16 8 768 - -

Maximum number of port-VLAN associations per LT 384 11520 11776 - -

Maximum number of VLAN port per UNI (FE/GE) - - - 8 -

Maximum number of VLAN port per NNI (FE/GE) - - - - 256

Maximum number of VLAN port per board (UNI) - - - 144 -

Maximum number of VLAN port per board (NNI) - - - - 4608

Maximum number of MAC addresses per VLAN port 64 64 8192 - -

Maximum number of MAC addresses per UNI - - - 64 -

Maximum number of MAC addresses per NNI - - - - 3072

Maximum number of MAC addresses per board (including static)

1024 16 K(2) 16 K 2304 32768

(1 of 2)



Notes(1) Due to thermal restrictions(2) A few MAC addresses are used by the system for internal purposes.

ISAM OLT Service and System Capacity

Service and system capacity

Table 1-16 provides specific dimensioning information of the GPON LT boards.

Table 1-16 GPON-specific Dimensioning Information

Maximum number of user IP addresses per board (including static)

384 8 K 7680 - -

Average number of IPv4 subnets or addresses per board (=Average IP anti-spoofing entries, full/32 IP address or subnet, per board

- - - 288 0

Maximum number of IPv4 hosts per board - - - 288 0

Maximum number of IPv6 subnets or addresses per UNI

- - - 16 0

Maximum number of IPv6 subnets or addresses per VLAN port

- - - 4 0

Maximum number of IPv6 host addresses per board - - - 288 0

Maximum number of VRFs per board 128 NA NA - -

Multicast Dimensioning

Maximum number of simultaneous multicast channels per board

1024 1024 1024 1024 1024

Maximum number of multicast groups per user 100 100 100 100 1024

Maximum number of multicast VLANs 128 128 64 - -

802.1x

Maximum number of 802.1x sessions per PON - 288 - - -

Maximum number of 802.1x sessions per UNI - - - 1 -

Maximum number of 802.1x sessions per board - 2304 - 36 -

Feature L3 L3GPON

L3EPON

NELT-B

UNI NNI

(2 of 2)

Feature L3 GPON

Maximum number of ONT per PON 128

Maximum number of UNIs per PON 512

Maximum number of TCONTs per PON 1024

Maximum number of GEM ports per PON 2048



ISAM OLT performance and distance

The ISAM OLT provides performance and distance capacity of 2.488 Gb/s downstream and 1.244 Gb/s upstream, within a 40 km span, for all NGLT boards. The optical link budget is defined by both loss and bandwidth characteristics. The loss characteristic is determined by the difference between the optical transmitter and optical receiver for each direction, and is typically 28 dB. The bandwidth characteristic is determined by the maximum link distance parameter of each OLT and ONT transmitter specification, and is limited by the smaller of the upstream and downstream values.

ISAM OLT connection capacities

The ISAM OLT can accommodate a maximum of 16 NGLT boards. Each NGLT board provides eight ports.

EPON Service and System CapacityTable 1-17 provides specific dimensioning information of the EPON LT boards.

Table 1-17 EPON-specific Dimensioning Information

1.6 NT Redundancy Support

Four levels of redundancy can be identified:

• Link redundancy• Equipment redundancy• Subscriber Line redundancy• Application redundancy

NT redundancy will implement the Link Redundancy and Equipment Redundancy in a decoupled architecture. This results in the following redundancy cases:

• Only link protection:single NT, active-standby or load-sharing uplinks.

• Combined NT and link protection, no NTIO:dual active/standby NT, with direct uplink or link set.

Feature L3 EPON

Maximum number of ONT per PON 64

Maximum number of ONT per EPON LT board 512

Maximum number of ONTs per system 8192

Maximum number of LLIDs per ONT 1

Maximum number of UNIs per PON 512

Maximum number of UNIs per LT board 4096

Maximum number of UNIs per system 26214



• Decoupled NT and link protection, single NTIO:dual active/standby NT, NTIO board with link switches.

• NT protection, passive link protection, no NTIO:single, active-standby or load sharing uplinks.

• Subtending system protection.

Table 1-18 shows which hardware modules are ready for NT redundancy support.

Table 1-18 NT Redundancy Support Ready Hardware Modules

1.7 CLEI Codes

Table 1-19 lists the boards and fan units for which CLEI codes are available.

Table 1-19 CLEI codes

Type Module

Subrack FX-16

FX-8

FX-4

NT boards FANT-F

NTIO boards FNIO-B

LT boards FPLT-A

NELT-B

NGLT-A

Caution — The CLEI code changes whenever an item change (that is, an adaptation to a board) occurs.

The latest status of these CLEI codes is always available on the following website:

https://codecenter.commonlanguage.com/applogin.asp?app=clei_inquiry

An account is required before the CLEI database can be accessed.

Mnemonic Variant CLEI code CPR Bar code

AFAN-H 3EC 37533 NB VAUCAE2KAA 070LXX 154967

FANT-F 3FE 53701 AC VAUKAKG6AA 072BWS 179981

FNIO-B 3FE 54057 AA VAI2AHNNAA 072CUP 181294

NELT-B 3FE 62543 AA VAUCAJ36AA 072AEY 177909

NGLT-A 3FE 64279 AA VAI2AFHDAA 070YVT 175498

(1 of 2)



NFXS-E 3FE 64936 AA VAM9F10DRA 214460 462367

NGFC-E 3FE 64985 AA VAUCAJ76AA 072AXH 178685

NFXS-F 3FE 64991 AA VAMVV10KRA 214392 462173

NGFC-F 3FE 64993 AA VAUCAJ66AA 072ARH 178373

AFAN-X 3FE 64994 AA VAUCAJ56AA 072ARC 178361

AFAN-E 3FE 65060 AA VAUCAJ86AA 072AXJ 178692

NFXS-D 3FE 65209 AA VAM9G10DRA 214458 462357

Mnemonic Variant CLEI code CPR Bar code

(2 of 2)




2 — Subracks


2.2 General 2-2

2.3 7360 ISAM FX Subracks 2-2

2.4 Supported Plug-in Units 2-6

2.5 Dummy Front Panels 2-7

2 — Subracks


2.1 Introduction

This chapter describes the different 7360 ISAM FX subracks supported for the European Telecommunication Standard Institute (ETSI) market.

2.2 General

The modular organization of the ISAM system allows a wide range of physical size and traffic capacity options.The basic building blocks of the ISAM system are the subracks or shelves(*).(*): Both names are used for the same item.The ISAM R 4.x is a one-subrack system. Daisy-chaining multiple subracks via extender boards is not supported.Multiple collocated subracks can be cascaded via the standard Fast Ethernet (FE)/Gigabit Ethernet (GE)/10Gigabit Ethernet (10GE) subtending links. In such a configuration, each subrack operates and is managed as a separate system.

2.3 7360 ISAM FX Subracks

Subrack Types

Table 2-1 lists the 7360 ISAM FX subracks supported in this release.

Table 2-1 7360 ISAM FX Subracks

Notes(1) Adapter brackets must be used

• Figure 2-1 shows the 7360 ISAM FX-16 subrack• Figure 2-2 shows the 7360 ISAM FX-8 subrack• Figure 2-3 shows the 7360 ISAM FX-4 subrack

Item 7360 ISAM FX Subracks

FX-16 FX-8 FX-4

Code 3FE 65209 AA 3FE64936 AA 3FE-64991 AA

Mnemonic NFXS-D NFXS-E NFXS-F

Dimensions (in mm) Width 529 482.5 482.5

Height 622.5 355 222

Depth max. 280 278.3 278.3

Can be mounted in: ETSI racks Y Y(1) Y(1)

19” racks N Y Y

2 — Subracks


Figure 2-1 7360 ISAM FX-16 Subrack



2 — Subracks


Subrack Configurations

Table 2-2 lists the possible subrack configurations.

Table 2-2 Subrack Configurations

The following figures show the general layout and the slot numbering for the different 7360 ISAM FX subracks:

• for a 7360 ISAM FX-16 subrack in LT mode; see Figure 2-4• for a 7360 ISAM FX-8 subrack; see Figure 2-5• for a 7360 ISAM FX-4 subrack; see Figure 2-6

Figure 2-4 7360 ISAM FX-16 subrack

Configuration 7360 FX-16 7360 FX-8 7360 FX-4

Maximum number of LT boards 16 8 4

Fan unit

CBs, LEDs and switches

Connectors

NT

A

NT

IO

NT

B

LT 8

LT 3

LT 9

LT 1

3

LT 4

LT 7

LT 1

2

LT 1

LT 2

LT 5

LT 6

LT 1

0

LT 1

1

LT 1

4

LT 1

5

LT 1

6

2 — Subracks




NT RedundancyThe protection scheme for NT redundancy is 1+1 (active/active) in the data plane, and 1:1 (active/standby) in the control and management plane.

Fan UnitOne fan unit provides forced air cooling in the subrack.

The fan unit is a field replaceable unit in the subrack fan area, it plugs directly into the backplane. The fan unit can be equipped with a dust filter.

LT 7

LT 6

LT 5

LT 4

LT 3

LT 2

LT 1

NT A

NT I/O

NT B

NGFC-E

FAN

LT 8

LT 4

LT 3

LT 2

LT 1

NT A

NT I/O

NT B

NGFC-F

FAN

2 — Subracks


2.4 Supported Plug-in Units

Table 2-3 lists the supported plug-in units in the 7360 FX subracks for the current release.

Table 2-3 Supported Units in 7360 FX Subracks

Slot Plug-in Unit Description

NT A FANT-F AC 480 Gbps NT board

NT B FANT-F AC 480 Gbps NT board

NTIO FNIO-B NT I/O board with 8 supplementary uplinks

LT slot NELT-B 36-line Ethernet (FE/GE) LT board

NGLT-A GPON LT board with 8 GPON interfaces

FPLT-A EPON LT board with 8 EPON interfaces

General facilities board NGFC-E General facilities and control board for FX-8 subrack

NGFC-F General facilities and control board for FX-4 subrack

Fan area AFAN-H NB Fan unit for FX-16 subrack

AFAN-E Fan unit for FX-8 subrack

AFAN-X Fan unit for FX-4 subrack

Note — For detailed information about the plug-in units, refer to the relevant UDS. The used mnemonics are explained in Appendix “Board Mnemonics”.

2 — Subracks


2.5 Dummy Front Panels

Dummy front panels must be mounted on any unused slot of a subrack for the following purposes:

• To ensure EMC compliance• To ensure thermal compliance via a correct airflow in the subrack• To ensure safety by avoiding direct contact with backplane connectors• At slot deployment, the dummy front plate is replaced by the appropriate board

and the cables are connected to the board.

For NT BoardThis panel (code 3FE 65651 AA) must be used when the second NT board is not installed. Figure 2-7 shows the dummy front panel for NT board.

Figure 2-7 Dummy Front Panel for NT Board

For Optical BoardsWhen optical cabling is already foreseen for not-installed optical LT boards (NGLT-A, FPLT-A), the optical cables must be fixed on dummy front panels (code 3FE 65005 AA). Figure 2-8 shows the dummy front panel.

2 — Subracks


Figure 2-8 Dummy Front Panel for Optical LT boards

Dust cap


3 — Physical Rack Equipment

3.1 General 3-2

3.2 Universal Rack 3-2

3.3 Side Plates 3-5

3.4 Rack Doors 3-6

3.5 Key Locks 3-7



3.1 General

The rack equipment can be delivered as a preassembled rack or in separate kits.

This rack assembly is a universal rack cabinet, dimensions 2200 mm x 600 mm x 300 mm, which can be equipped with subracks, accompanying fan units and power and alarm cabling. Each rack configuration is ordered with a specific ordering code.

Different parts can also be delivered separately or in kits, the assembly is done on site at the customer.

3.2 Universal Rack

Cabinet Types

Table 3-1 shows the specifications of the universal rack.

Table 3-1 Cabinet Type used for FX Equipment

Figure 3-1 Universal Rack

Type Code Height Floorspace Drawing

Universal 3FE 28688 AA 2200 mm 600 x 300 mm Figure 3-1



Transport Bracket

The transport bracket is mounted on the universal rack to protect the door from damage during transport.

Figure 3-2 Transport Bracket

On site the bracket must be removed.

Cabling SpaceAs shown in Figure 3-1, the universal cabinet provides the space required for cabling. Position and dimensions of side holes are adapted for routing cables of all subracks in any configuration.

If required, the bottom plate can be removed as shown in Figure 3-3, to free bottom holes that allow cable routing under raised floor.

Transportbracket



Figure 3-3 Top and inside Bottom View

Top view

Bottom view inside cabinet

Floor plate mounted Floor plate removed(cable routing via bottom holes)



3.3 Side Plates

Table 3-2 specifies the items which are required to equip a universal rack with side plates (left or right).

Table 3-2 Side Plate Fixing Items

The same kit is used for mounting a side plate on the left or on the right. Figure 3-4 shows the right side plate.

Figure 3-4 Mounting Side Plate on Universal Rack

When mounting or dismounting the side plate, always remove the corner upright (item 4 in Figure 3-4) first. Each side plate is mounted with 5 screws and washers on the front and 5 screws and washers on the side.

Description Quantity Item No. on Figure 3-4

Side plate 2 1

Screw M4 20 2

Washer M4 20 3



3.4 Rack Doors

One universal door is available (code 3FE 20207 JC). The door opens to the left and can be closed by means of two door latch locks.

Figure 3-5 Universal Rack with Right Side Door

Refer to the 7360 ISAM FX Hardware Installation Manual for installation procedure.



3.5 Key Locks

The door latch locks can be replaced on site by key locks. A key lock kit can be ordered separately (code 3FE 25800 AA). This kit contains two key locks, two keys and instructions to replace the standard latch locks by key locks.

Figure 3-6 Key Lock Kit

Refer to the 7360 ISAM FX Hardware Installation Manual for installation procedure.




4 — Rack Configurations

4.1 General 4-2

4.2 Rack Configurations 4-2



4.1 General

This chapter describes the supported rack configurations for the 7360 ISAM FX-16 subrack.

An rack contains:

• A rack cabinet: 2200 mm high.• A door opening/closing on the left or the right side with a handle or a lock.• One or two subrack(s) depending on the rack configuration.• One fan unit per equipped subrack, for equipment cooling.

4.2 Rack Configurations

Table 4-1 gives an overview of all the possible rack configurations with 7360 ISAM FX-16 subracks. These configurations are shown in Figure 4-1.

Table 4-1 Rack Configurations with 7360 ISAM FX-16 subracks

Code 3FE 65679 AA 3FE 65680 AA

Cabinet 3FE 28688 AA

SR 1 NFXS-D

(3FE 65209 AA)

NFXS-D

(3FE 65209 AA)

Fan1 AFAN-H(with dust filter)

(3EC 37533 NB)

AFAN-H(with dust filter)

(3EC 37533 NB)

SR 2 - NFXS-D

(3FE 65209 AA)

Fan 2 - AFAN-H(with dust filter)

(3EC 37533 NB)



Figure 4-1 Rack Configurations with 7360 ISAM FX-16 subracks

3FE 65679 AA 3FE 65680 AA




5 — SFP Optical Modules


5.2 SFP Optical Modules 5-2



5.1 Introduction

This section lists the Alcatel-Lucent-approved Small Form Pluggable (SFP) modules that are supported for each board type.

5.2 SFP Optical Modules

Table 5-1 lists the Alcatel-Lucent-approved Small Form Pluggable (SFP) optical modules that are supported for each board type.

Table 5-2 lists different characteristics of these SFP modules.

Table 5-1 Supported SFP Modules per Board Type

Code Description

FA

NT

-F

FN

IO-B

NEL

T-B

NG

LT-A

FPLT

-A

Fast Ethernet SFP

3FE 25777 AA FE-FX Y

3FE 25778 AA FE-LX10 Y

3FE 29194 AA FE BX-10-D Y

3FE 29194 BA FE BX-10-D Y

3FE 29195 AA FE BX-10-U Y

3FE 63343 AA 100Base-T Y

Gigabit Ethernet SFP

3FE 25773 AA GE-SX

3FE 25774 AA GE-LX Y Y

3FE 25775 AA GE-EX Y

3FE 25776 AA GE-ZX Y

3FE 25771 AA GE-YX CWDM (24 dB)

3FE 25771 AB

3FE 25771 AC

3FE 25771 AD

3FE 25771 AE

3FE 25771 AF

3FE 25771 AG

3FE 25771 AH

(1 of 2)



Notes(1) This is a dual-rate compact SFP

3FE 25771 CA GE-VX CWDM (32 dB)

3FE 29549 CA

3FE 29550 CA

3FE 29551 CA

3FE 29552 CA

3FE 29553 CA

3FE 29554 CA

3FE 29555 CA

3FE 25772 AA GE-BX10-U Y

3FE 25772 AB GE-BX10-D Y Y Y

3FE 28784 AA 1000Base-T Y Y Y

3FE 28785 AA GE-BX40-U Y

3FE 28785 AB GE-BX40-D Y

SFP+

3FE 62600 AA 10GE-R

3FE 62600 CA 10GE-R

3FE 62600 DA 10GE-R Y

3FE 62600 EA 10GE-R Y

3FE 65608 AA 10GE-R Y

3FE 63264 AA 10GE-R Y

3FE 65831 AA 10GE-R Y

3FE 65832 AA 10GE-R

Dual SFP

3FE 65106 AA GE-BX10-D Y

3FE 65107 AA FE-BX10-D Y

3FE 66131 AA(1) FE-BX10-D

GE-BX-10-D

Y

Y

GPON SFP

3FE 53441 AC GPON SFP B+ Y

3FE 53441 BA GPON SFP C+ Y

3FE 53441 CC with OTDR GPON SFP B+ with OTDR Y

EPON SFP

3FE 53606 AA EPON PX20+ Y

3FE 66282 AA EPON PX20+ OTDR Y

Code Description

FA

NT

-F

FN

IO-B

NEL

T-B

NG

LT-A

FPLT

-A

(2 of 2)



Table 5-2 Characteristics of Approved SFP Modules

Code Description Wavelength(nm)

Operating CaseTemp. Range (°C)

OpticalBudget(dB)

Reach(km)

Fiber Bidi/Uni

UDS(1)

Fast Ethernet SFP

3FE 25777 AA FE-FX 1310 -40..+85 12 0.550 MM Uni DAAA

3FE 25778 AA FE-LX10 1310 -40..+85 16 15 SM Uni

3FE 29194 AA FE BX-10-D TX: 1550

RX: 1310

-40..+85 14 10 SM Bidi FAAA

3FE 29194 BA FE BX-10-D TX: 1490

RX: 1310

-40..+85 14 10 SM Bidi

3FE 29195 AA FE BX-10-U TX: 1310

RX: 1550

-40..+85 14 10 SM Bidi

3FE 63343 AA 100Base-T NA 0..+70 NA 0.100 Cat5 NA PAAA

Gigabit Ethernet SFP

3FE 25773 AA GE-SX 850 -40..+85 7 0.550 MM Uni CAAA

3FE 25774 AA GE-LX 1310 -40..+85 11 10 SM Uni

3FE 25775 AA GE-EX 1310 -40..+85 18 40 SM Uni

3FE 25776 AA GE-ZX 1550 -40..+85 24 80 SM Uni

3FE 25771 AA GE-YX

CWDM

(24 dB)

1471 -40..+85 22 62 SM Uni AAAA

3FE 25771 AB 1491

3FE 25771 AC 1511

3FE 25771 AD 1531

3FE 25771 AE 1551

3FE 25771 AF 1571

3FE 25771 AG 1591

3FE 25771 AH 1611

3FE 25771 CA GE-VX

CWDM

(32 dB)

1471 -5..+85 31 120 SM Uni

3FE 29549 CA 1491

3FE 29550 CA 1511

3FE 29551 CA 1531

3FE 29552 CA 1551

3FE 29553 CA 1571

3FE 29554 CA 1591

3FE 29555 CA 1611

(1 of 2)



3FE 25772 AA GE-BX10-U TX: 1310

RX: 1490

-40..+85 9 10 SM Bidi GAAA

3FE 25772 AB GE-BX10-D TX: 1490

RX: 1310

-40..+85 9 10 SM Bidi

3FE 28785 AA GE-BX40-U TX: 1310

RX: 1550

-40..+85 19 40 SM Bidi

3FE 28785 AB GE-BX40-D TX: 1550

RX: 1310

-40..+85 19 40 SM Bidi

3FE 28784 AA 1000Base-T NA 0..+85 NA 0.100 Cat5 NA EAAA

SFP+

3FE 62600 AA 10GE-R 1310 -40..+85 10 10 SM Uni MAAA

3FE 62600 CA 10GE-R 1310 -5..+85 10 10 SM Uni

3FE 62600 DA 10GE-R 1310 0..+70 10 10 SM Uni

3FE 62600 EA 10GE-R 1310 -40..+85 10 10 SM Uni

3FE 65608 AA 10GE-R 850 0..+70 11 0.3 MM Uni

3FE 63264 AA 10GE-R 850 -40..+85 11 0.3 MM Uni

3FE 65831 AA 10GE-R 1550 -40..+85 15 40 SM Uni

3FE 65832 AA 10GE-R 1550 -40..+85 24 80 SM Uni

Dual SFP

3FE 65106 AA GE-BX10-D TX: 1490

RX: 1310

-40..+85 9 10 SM Bidi

TAAA3FE 65107 AA FE-BX10-D TX: 1550

RX: 1310

-40..+85 14 10 SM Bidi

3FE 66131 AA FE-BX10-D

GE-BX10-D

TX: 1490

RX: 1310

-40..+85 8 (FE)

9 (GE)

10 SM Bidi

GPON SFP

3FE 53441 AC Class B+, normal

TX: 1490

RX: 1310

-40..+85 28 30 SM Bidi

RAAA3FE 53441 BA Class C+,

normalTX: 1490

RX: 1310

-5..+70 32 60 SM Bidi

3FE 53441 CC Class B+, with OTDR

TX: 1490

RX: 1310

-40..+85 28 30 SM Bidi

EPON SFP

3FE 53606 AA EPON PX20+ TX: 1490

RX: 1310

-40..+85 32 20 SM Bidi UAAA

3FE 66282 AA EPON PX20+ OTDR

TX: 1490

RX: 1310

-40..+85 32 20 SM Bidi

Code Description Wavelength(nm)

Operating CaseTemp. Range (°C)

OpticalBudget(dB)

Reach(km)

Fiber Bidi/Uni

UDS(1)

(2 of 2)



Note(1) For more detailed information on the different characteristics of the SFP module, refer to UDS 3HH

01046 xxxx TQZZA (where xxxx is the document variant indicated in this column).

Alcatel-Lucent 7360 ISAM FX R4.3 July 2011 A-13HH-10116-AAAA-TCZZA Edition 01 Released Product Information

A. Board Mnemonics

A.1 Board Mnemonics A-2

A. Board Mnemonics

A-2 July 2011 Alcatel-Lucent 7360 ISAM FX R4.3Product Information Edition 01 Released 3HH-10116-AAAA-TCZZA

A.1 Board Mnemonics

Table A-1 gives the used board mnemonics with their description.

Table A-1 Mnemonics

Mnemonic Description

AFAN-H Fan unit - version H

AFAN-E FX-8 Fan unit - version E

AFAN-X FX-4 Fan unit - version X

FANT-F Combined NT Unit - version F

FNIO-B FX FE/GE Network Termination I/O Applique - version B

FPLT-A EPON Line Termination Board - version A

NELT-B 36-line Fast Ethernet/Gigabit Ethernet Line Termination Unit - version B

NFXS-D FX-16 Shelf for ETSI/MII

NFXS-E FX-8 Shelf for ETSI/MII

NFXS-F FX-4 Shelf for ETSI/MII

NGFC-E General Facilities Card - version E

NGFC-F General Facilities Card - version F

NGLT-A GPON Line Termination Board - version A

Alcatel-Lucent 7360 ISAM FX R4.3 July 2011 IN-13HH-10116-AAAA-TCZZA Edition 01 Released Product Information

Index

Numbers

7360 FXrack configurations, 4-2subrack configurations, 2-4subrack types, 2-2Supported plug-in units, 2-6

C

CLEI codes, 1-26

D

Dimensioning, 1-19GPON, 1-24

Dummy front panels, 2-7

G

GPONdimensioning, 1-24

I

IWFcapabilities, 1-19

M

ManagementNetwork, 1-17

N

Network topology, 1-2Network side, 1-4User side, 1-3

P

Plug-in units, 2-6

R

Redundancy support1+1 NT, 1-25

S

SFP modules, 5-2System architecture, 1-6

IHub, 1-16

T

Technical specificationsP-OLT connection capacity, 1-25

Index

IN-2 July 2011 Alcatel-Lucent 7360 ISAM FX R4.3Product Information Edition 01 Released 3HH-10116-AAAA-TCZZA

U

Universal rack, 3-2Locks, 3-7Rack door, 3-6Side plates, 3-5type, 3-2

U — Universal rack

Customer documentation and product support

Customer documentationhttp://www.alcatel-lucent.com/myaccessProduct manuals and documentation updates are available at alcatel-lucent.com. If you are a new user and require access to this service, please contact your Alcatel-Lucent sales representative.

Technical Supporthttp://www.alcatel-lucent.com/support

Documentation [email protected]

http://www.alcatel-lucent.com/myaccess

http://www.alcatel-lucent.com/support

mailto:[email protected]

© 2011 Alcatel-Lucent. All rights reserved.3HH-10116-AAAA-TCZZA Edition 01 Released

3hh 10116 Aaaa Tczza 01 7360 Isam Product Information r4_3_x

Documents

alcatellucent logo

alcatellucent harmless

general information

incomplete information

failure of products

english version

isam fx r4

scopethis documentation