8/3/2019 3d Training
1/15
Installation
Pitch Test
Before installation1.D: drive should be Separate partition and free space required.
2.If windows 7 , install by right click then run as administrator.3.If not installed, pause the anti-virus for few seconds.4.Insert cd and double click the "exe" file5.Insert softkey or Dongle in USB port.6.Finally open the software.7.This software will not work in windows vista.
Pitch is the exact count of lenticules per inch (LPI). This refers to matching the
rendered 3dfile with the frequency and spacing of the lens material.
C:/program file/Antz Technologies/ pitch/ PitchRange_8_60_420C:/program file/Antz Technologies/ pitch/ PitchRange_8_40_480Print the file in any Desktop photo printer i.e: epson/canon/HP/ Brother
Take print of the following Pitch files
Beginer
TM
Pitch value for 60 Lpi: 420
The above image is an example of one type pitch testfile. It consists of various differentfrequencies of lines for a certain LPI. It may be necessary to resize an rendered image to fitthe lens more appropriately. The alignment bars are used for aligning the image and the lensas well as adjusting the pitch.
Pitch value for 40 Lpi: 478.505
8/3/2019 3d Training
2/15
Lentricks_3D Tutorial
8/3/2019 3d Training
3/15
Choose the artworkwhich is ready to create
Choose theLens and Depth
After choosing the
parametersPlay for view
Draw line
Depth can be kept as .5" for 8"x10" sizesThe depth can be adjusted according to the size of the images too.
Go to draw line and using the draw tool, you can now choose the area of the image which should be higlighted.For example if you want adjustments there are15 steps to be taken for volumetric effects
This is usedas selectiontool tocreate volumetric
The volumetric iscreated asseveral steps
Import the psd file
.5
8/3/2019 3d Training
4/15
Click the previewbutton to see the
Stop the prev
Set layer/Select to anothLayer.
Preview
After another layer to create the volumetric effect
8/3/2019 3d Training
5/15
Stop
8/3/2019 3d Training
6/15
Preview
8/3/2019 3d Training
7/15
You can set valueaccording to the d
Stop and Save
the file forFurther Use
Stop
After Setting the Vaplay the preview to over all depth
8/3/2019 3d Training
8/15
Resampling Pitch
After Rendering the file.
Open in Photoshop
Change the Value as per your pitch test result ( 418.505)
"Off" theResampleimage
418.505
Change the Value as per your original out put resolutions 480
"on" theResampleimage
480
Printing
8/3/2019 3d Training
9/15
Alignment and Lamination
This image illustrates bad alignmentThe alignment bars have "zebra" type pattern
This image illustrates good alignmentThe alignment appear as either solid black or white
Release the tape for1 inch down and paste slowly
Use Cold laminating machine for lamination. 3D is Ready,
Use tapes at both side edges, for easy releasingself adhesive.
Adjust the alignment bar in the print out taken with the appropriate lens, so that the image strips are parallel to lenticules.The alignment bars produced during rendering are necessary for achieving proper lens alignment during the printing.You can set the size of the alignment bars to match your project requirements.Proper lens alignment is crucial in achieving a good effect.
8/3/2019 3d Training
10/15
Lentricks_Merge
8/3/2019 3d Training
11/15
Choose theWidth and Height
Choose theLens (40)
Import the .BMPfile which is readyfor Flip
Click and choose thesame file up to 6 times.
8/3/2019 3d Training
12/15
Click and choose theanother file andcontinue from 7 to
12 frames of samemage
Click merge
8/3/2019 3d Training
13/15
8/3/2019 3d Training
14/15
"OFF " theResampleimage
Printing
"ON " theResampleimage
Change the Value as per your pitch test result ( 478.505)
Change the Value as per original out put resolutions 480
Open Merged File in Photoshop for Resampling image
Resampling Pitch
8/3/2019 3d Training
15/15
Alignment and Lamination
This image illustrates bad alignmentThe alignment bars have "zebra" type pattern
This image illustrates good alignmentThe alignment appear as a solid black or white
Release the tape for one inch down and paste slowly
Use Cold laminating machine for lamination. Flip image Ready.
Paste the tape at both side edges, for easy releasingself adhesive.
Adjusting an merged image so that the image strips are parallel to lenticules. The allignment bars produced duringrendered are necessary for achieving proper lens alignment during the printing. you can set the size of the alignment barsto match your project requirements. proper lens alignment is crucial in achieving a good effect.
Alignment and Lamination