AMS-8923 Connection Diagram 399800, Rev B A, Initial Release - May, 2010 1, Custom Design - August, 2007 B, Revised Release - April, 2017 Revision / Date: ets-lindgren.com ets-lindgren.com Note: ETS-Lindgren may substitute a similar part with the same functionality for another part. Warranty Information e h t e e s , n o i t a m r o f n i y t n a r r a w r o F Product Information Bulletin. Product Information Bulletin : g n i w o l l o f e h t r o f t n e m p i h s r u o y h t i w d e d u l c n i n e r g d n i L - S T E e h t e e S Product Information Bulletin Warranty information Safety, regulatory, and other product marking information Steps to receive your shipment Steps to return a component for service ETS-Lindgren calibration service ETS-Lindgren contact information © Copyright 2007-2017 by ETS-Lindgren Inc. All Rights Reserved. No part of this document may be copied by any means without written permission from ETS-Lindgren Inc. The logo is a registered trademark of ETS-Lindgren Inc. ETS-Lindgren USA Headquarters 1301 Arrow Point Drive Cedar Park, TX 78613 Phone: +1.512.531.6400 Please see ets-lindgren.com for a list of all ETS-Lindgren offices. WARRANTY . t n e m p i h s r u o y h t i w d e d u l c n i e h t e e s , n o i t a m r o f n i y t e f a s l a n o i t i d d a r o F Product Information Bulletin Safety Information Laser Danger: Denotes a laser (IEC Class 3B) is part of the operating system of the device. Laser power range is 5-500 mW. Visible laser radiation: Avoid exposure to beam. Do not stare into beam or view directly with optical instruments. Left Side Right Side Right Top Right Bottom Control Box (part# 114760) • EMCenter Modular RF Platform TM • TEST INSTRUMENT Test Instrumentation (required units provided by customer) • • AMS-8923 installed in finished chamber (part# 114700) • Interconnect Kit (part# 115018) Laser Control (part# 115017) Sensor Position Display (part# 115014) Laser Cable (part# 665080) 4-Conductor Cable (part# 660046) (part# 660047) 8-Conductor Cable (part# 705344-10) Fiber Optic Cable (part# 106043-10m) BNC Cable • 10-Meter Fiber Optic Cable (part# 705344-10) Additional cables (as required by configuration) HIGH VOLTAGE: Indicates presence of hazardous voltage. Unsafe practice could result in severe personal injury or death. CONTACT ETS-LINDGREN PRIOR TO SERVICING. Servicing (or modifying) the unit by yourself may void your warranty if you attempt to service the unit by yourself, disconnect all electrical power before starting. There are voltages at many points in the instrument that could, if contacted, cause personal injury. Only trained service personnel should perform adjustments and/or service procedures upon this instrument. Capacitors inside this instrument may still be CHARGED even when instrument is disconnected from its power source. BEFORE POWER IS APPLIED TO THIS INSTRUMENT, GROUND IT PROPERLY through the protective conductor of the AC power cable to a power source provided with protective earth contact. Any interruption of the protective (grounding) conductor, inside or outside the instrument, or disconnection of the protective earth terminal could result in personal injury. These components are required to connect the AMS-8923 Measurement System: +105 +90 +75 +60 +45 +30 +15 0 PHI -15 -30 -45 -60 -75 -90 -105 -120 PHI THETA +105 +90 +75 +60 +45 +30 +15 0 THETA -15 -30 -45 -60 -75 -90 -105 -120 -135 -150 -165 +165 +150 +135 +120 PHI -135 -150 -165 +165 +150 +135 +120 THETA RF PORTS 100/240 VAC 50/60 Hz 100 VA M AX AMS–8923 Controller Box Part #114760 LASER LASER SWITCH DISPLAY THETA PHI DEDICATED PATHS SWITCHED PATH TRIGGER OUTPUT ™ Laser On Power On EMCenter Interlock Standby OF F ON ALIGNMENT LASERS