312751G ENG Repair - Parts Gusmer-Decker RC Polyurethane Processing Equipment For dispensing controlled ratio shots of resin and isocyanate. For professional use only. Not approved for use in European explosive atmosphere locations. 3000 psi (21 MPa, 207 bar) Maximum Working Pressure 100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure Important Safety Instructions Read all warnings and instructions in this and all supplied manuals. Save these instructions. ti11588b
74
Embed
312751G - Gusmer-Decker RC, Repair-Parts, English ENG Repair - Parts Gusmer-Decker RC Polyurethane Processing Equipment For dispensing controlled ratio shots of resin and isocyanate.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
312751GENG
Repair - Parts
Gusmer-Decker RCPolyurethane Processing Equipment
For dispensing controlled ratio shots of resin and isocyanate. For professional use only.
Not approved for use in European explosive atmosphere locations.
3000 psi (21 MPa, 207 bar) Maximum Working Pressure100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure
Important Safety InstructionsRead all warnings and instructions in thisand all supplied manuals. Save theseinstructions.
Product ConfiguratorThis system can be ordered with many different options as shown in the configurator below.
The following table applies to the RC configurations and indicates all of the options available for each letter shownabove.
RC - C - A - B - C - D - E - F - G - H - I - J - K - L - M - N - O - P - Q - R - S - TU - VW - XY - AA - AB
Configurator
Series
Level
Base
UnitM
odule
Voltage/F
useP
ackage
IsoP
umpline
IsoLube
Kit
Poly
Pum
pline
Poly
LubeK
it
Iso/Poly
Pum
plineV
ariableF
requencyD
riveK
its
Day
Tanks
MixH
ead#1
MixH
ead#1
Hose
Kit
Pour
Pendant
Stand
Alone
Chiller
Heating
System
Volum
etricF
lowM
eters
IsoT
ankA
gitation
Poly
Tank
Agitation
Auto-F
ill
DualS
witching
Station
with
Hose
Package
andP
ourP
endant
MixH
ead#2
IsoN
eedle/Orifice
Kitfor
MixH
ead#1
Poly
Needle/O
rificeK
itforM
IxHead
#1
IsoN
eedle/Orifice
Kitfor
MixH
ead#2
Poly
Needle/O
rificeK
itforM
ixHead
#2
CS
AA
pproval
Code A Base Unit Module
2 Base, 20 lb/min (151 grams/sec)
3 Base, 40 lb/min (302 grams/sec)
4 Base, 100lb/min (756 grams/sec)
Code B Voltage/Fuse Package
A RC 20/40 230V 3PH
B RC 20/40 380-400V 3PH
C RC 20/40 460 V 3PH
E RC 100 230V 3PH
F RC 100 380-400V 3PH
G RC 100 460V 3PH
Code C Iso Pumpline
1 5 hp, 900 rpm, 5 cc
2 5 hp, 1800 rpm, 5 cc
3 15 hp, 1800 rpm, 12 cc
4 5 hp, MAG drive, 900 rpm, 5 cc
5 5 hp, MAG drive, 1800 rpm, 5 cc
6 15 hp, MAG drive, 1800 rpm, 12 cc
Code D Iso Lube Kit
N None
A Static Lube Kit
B Seal Flush Kit
Code E Poly Pumpline
1 5 hp, 900 rpm, 5 cc
2 5 hp, 1800 rpm, 5 cc
3 15 hp, 1800 rpm, 12 cc
4 5 hp, MAG drive, 900 rpm, 5 cc
5 5 hp, MAG drive, 1800 rpm, 5 cc
6 15 hp, MAG drive, 1800 rpm, 12 cc
Code F Poly Lube Kit
N None
A Static Lube Kit
B Seal Flush Kit
Code GIso/Poly Pumpline
Variable Frequency Drive Kits
1 5 cc 230V VFD Kit
2 5 cc 400-460V VFD Kit
3 12 cc 230V VFD Kit
4 12 cc 400-460V VFD Kit
5 Contactor Kit - No VFD
Product Configurator
312751G 5
Code H Day Tanks, 20 gal (75.7 L)
A Mild Steel, with 40 mesh, standard
B Mild Steel, with 40 mesh, placite
C Mild Steel, with 60 mesh, standard
D Mild Steel, with 60 mesh, placite
E Mild Steel, with 80 mesh, standard
F Mild Steel, with 80 mesh, placite
G Mild Steel, with 100 mesh, standard
H Mild Steel, with 100 mesh, placite
Code I MixHead #1
N None
1 L-Head 5/8 with Calibration Orifice Kit
2 L-Head 6/10 with Calibration Orifice Kit
3 L-Head 10/14 with Calibration Orifice Kit
4 L-Head 13/20 with Calibration Orifice Kit
5 L-Head 16/25 with Calibration Orifice Kit
6 S-Head 6-500 with Calibration Orifice Kit
7 S-Head 6-625 with Calibration Orifice Kit
9 S-Head 6-500 L/S with Calibration Orifice Kit
A S-Head 6-625 L/S with Calibration Orifice Kit
Code J MixHead #1 Hose Kit
N None
A L-Head Hose Kit, 15 ft, with Boom
B S-Head Hose Kit, 15 ft, with Boom
C L-Head Hose Kit, 15 ft, without Boom
D S-Head Hose Kit, 15 ft, without Boom
E L-Head Hose Kit, 25 ft, without Boom
F S-Head Hose Kit, 25 ft, without Boom
G L-Head Hose Kit, 40 ft, without Boom
H S-Head Hose Kit, 40 ft, without Boom
Code K Pour Pendant
N Standard Pour Pendant, 20 meter cable (includedin Base Unit Module, Code A)
Code L Stand Alone Chiller
N None
B 1PH, 230V, 1 ton
C 1PH, 230V, 2 ton
D 3PH, 230V, 3 ton
F 3PH, 460V/2.5 ton, 400V/2.0 ton
G 3PH, 460V/3.5 ton, 400V/3.0 ton
H 3PH, 460V/5.0 ton, 400V/4.5 ton
Code M Heating System
N None
1 Heater Assembly, Iso & Poly
Code N Volumetric Flow Meters
N None
A Set of 2 with controls, 20 lb/min (151 grams/sec)or 40 lb/min (302 grams/sec),0.01-0.5 gpm (0.037-1.89 lpm)
B Set of 2 with controls, 20 lb/min (151 grams/sec)or 40 lb/min (302 grams/sec),0.2-2 gpm (0.76-7.6 lpm)
C Set of 2 with controls, 100 lb/min (756 grams/sec)
Code O Iso Tank Agitation
N None
1 Agitator pre-wire kit, no motor
2 Fixed speed agitator, 230-460V
3 Variable Speed Agitator, 230V, iso
4 Variable Speed Agitator, 400-460V, iso
Code P Poly Tank Agitation
N None
1 Agitator pre-wire kit, no motor
2 Fixed speed agitator, 230-460V
3 Variable Speed Agitator, 230V, poly
4 Variable Speed Agitator, 400-460V, poly
Code Q Auto-Fill
N None
A Auto-Fill controls, no pumps
B Auto-Fill controls withtwo (2) diaphragm pumps
C Auto-Fill controls with two (2) 2:1 stick pumps
Code RDual Switching Station with
Hose Package and Pour Pendant
N None
1 Dual Switching Station for 2nd L-Head, 15 ft
2 Dual Switching Station for 2nd S-Head, 15 ft
3 Dual Switching Station for 2nd L-Head, 25 ft
4 Dual Switching Station for 2nd S-Head, 25 ft
5 Dual Switching Station for 2nd L-Head, 40 ft
6 Dual Switching Station for 2nd S-Head, 40 ft
Product Configurator
6 312751G
Code S MixHead #2
N None
1 L-Head 5/8 with Calibration Orifice Kit
2 L-Head 6/10 with Calibration Orifice Kit
3 L-Head 10/14 with Calibration Orifice Kit
4 L-Head 13/20 with Calibration Orifice Kit
5 L-Head 16/25 with Calibration Orifice Kit
6 S-Head 6-500 with Calibration Orifice Kit
7 S-Head 6-625 with Calibration Orifice Kit
9 S-Head 6-500 L/S with Calibration Orifice Kit
A S-Head 6-625 L/S with Calibration Orifice Kit
CodesTU, VW,XY, AA
Needle/Orifice Size Kits;Orifice Size (mm)
NN None
00 Calibration Orifice
0A 0.25
0B 0.35
0D 0.45
0E 0.50
0G 0.60
0H 0.70
0J 0.75
0K 0.80
0L 0.85
0M 0.90
1A 1.00
1B 1.10
1C 1.20
1D 1.25
1E 1.30
1G 1.40
1J 1.50
1L 1.60
1M 1.65
1N 1.70
1P 1.75
1Q 1.80
1S 1.90
Needle/Orifice Size Kits (continued)
2A 2.00
2E 2.40
2F 2.50
3A 3.00
3C 3.20
3F 3.50
3G 3.60
4A 4.00
4C 4.20
4F 4.50
5A 5.00
5F 5.50
5G 5.60
6A 6.00
6F 6.50
7A 7.00
CodeAB CSA Approval
NC No CSA Approval Required
CA CSA Approval Required
Warnings
312751G 7
WarningsThe following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer backto these warnings. Additional, product-specific warnings may be found throughout the body of this manual whereapplicable.
DANGERHIGH VOLTAGE ELECTRIC SHOCK HAZARDContact with high voltage equipment and improper grounding, setup, or usage of the system can causedeath or serious injury.• Turn off and disconnect power at main switch before disconnecting any cables and before servicing
equipment.• This equipment must be grounded. Connect only to grounded power source.• All electrical wiring must be done by a qualified electrician and comply with all local codes and
regulations.
WARNINGTOXIC FLUID OR FUMES HAZARDToxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, orswallowed.• Read MSDS’s to know the specific hazards of the fluids you are using.• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.• Always wear impervious gloves when spraying or cleaning equipment.
PERSONAL PROTECTIVE EQUIPMENTYou must wear appropriate protective equipment when operating, servicing, or when in the operatingarea of the equipment to help protect you from serious injury, including eye injury, inhalation of toxicfumes, burns, and hearing loss. This equipment includes but is not limited to:• Protective eyewear• Clothing and respirator as recommended by the fluid and solvent manufacturer• Gloves• Hearing protection
SKIN INJECTION HAZARDHigh-pressure fluid from dispense valve, hose leaks, or ruptured components will pierce skin. This maylook like just a cut, but it is a serious injury that can result in amputation. Get immediate surgicaltreatment.• Do not point dispense valve at anyone or at any part of the body.• Do not put your hand over the end of the dispense nozzle.• Do not stop or deflect leaks with your hand, body, glove, or rag.• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,
checking, or servicing equipment.
PRESSURIZED EQUIPMENT HAZARDFluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin andcause serious injury.• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,
checking, or servicing equipment.• Tighten all fluid connections before operating the equipment.• Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
Warnings
8 312751G
FIRE AND EXPLOSION HAZARDFlammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help preventfire and explosion:• Use and clean equipment only in well ventilated area.• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop
cloths (potential static arc).• Keep work area free of debris, including solvent, rags and gasoline.• Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.• Ground equipment, personnel, object being sprayed, and conductive objects in work area. See
Grounding instructions.• Use only Graco grounded hoses.• Check gun resistance daily.• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment
until you identify and correct the problem.• Do not flush with gun electrostatics on. Do not turn on electrostatics until all solvent is removed from
system.• Keep a working fire extinguisher in the work area.
PRESSURIZED ALUMINUM PARTS HAZARDDo not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluidscontaining such solvents in pressurized aluminum equipment. Such use can cause serious chemicalreaction and equipment rupture, and result in death, serious injury, and property damage.
EQUIPMENT MISUSE HAZARDMisuse can cause death or serious injury.• Do not operate the unit when fatigued or under the influence of drugs or alcohol.• Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete informationabout your material, request MSDS forms from distributor or retailer.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-facturer’s replacement parts only.
• Do not alter or modify equipment.• Use equipment only for its intended purpose. Call your distributor for information.• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.• Do not kink or over bend hoses or use hoses to pull equipment.• Keep children and animals away from work area.• Comply with all applicable safety regulations.
MOVING PARTS HAZARDMoving parts can pinch or amputate fingers and other body parts.• Keep clear of moving parts.• Do not operate equipment with protective guards or covers removed.• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,
follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.
BURN HAZARDEquipment surfaces and fluid that’s heated can become very hot during operation. To avoid severeburns, do not touch hot fluid or equipment. Wait until equipment/fluid has cooled completely.
WARNING
Isocyanate Hazard
312751G 9
Isocyanate Hazard
Material Self-ignition
Moisture Sensitivity ofIsocyanatesIsocyanates (ISO) are catalysts used in two componentfoam and polyurea coatings. ISO will react with moisture(such as humidity) to form small, hard, abrasive crystals,which become suspended in the fluid. Eventually a filmwill form on the surface and the ISO will begin to gel,increasing in viscosity. If used, this partially cured ISOwill reduce performance and the life of all wetted parts.
To prevent exposing ISO to moisture:
• Always use a sealed container with a desiccantdryer in the vent, or a nitrogen atmosphere. Neverstore ISO in an open container.
• Keep the ISO lube pump reservoir (if installed) filled
with Graco Throat Seal Liquid (TSL™), Part 206995.The lubricant creates a barrier between the ISO andthe atmosphere.
• Use moisture-proof hoses specifically designed forISO, such as those supplied with your system.
• Never use reclaimed solvents, which may containmoisture. Always keep solvent containers closedwhen not in use.
• Never use solvent on one side if it has been contam-inated from the other side.
• Always lubricate threaded parts with ISO pump oilor grease when reassembling.
Keep Components A andB Separate
Foam Resins with 245 faBlowing AgentsNew foam blowing agents will froth at temperaturesabove 90°F (33°C) when not under pressure, especiallyif agitated. To reduce frothing, minimize preheating in acirculation system.
Changing Materials• When changing materials, flush the equipment mul-
tiple times to ensure it is thoroughly clean.
• Always clean the fluid inlet strainers after flushing.
• Check with your material manufacturer for chemicalcompatibility.
• Most materials use ISO on the A side, but some useISO on the B side.
• Epoxies often have amines on the B (hardener)side. Polyureas often have amines on the B (resin)side.
Read material manufacturer’s warnings and materialMSDS to know specific hazards and precautionsrelated to isocyanates.
Prevent inhalation of isocyanate mists, vapors, andatomized particulates by providing sufficient ventila-tion in the work area. If sufficient ventilation is notavailable, a supplied-air respirator is required foreveryone in the work area.
To prevent contact with isocyanates, appropriate per-sonal protective equipment, including chemicallyimpermeable gloves, boots, aprons, and goggles, isalso required for everyone in the work area.
Some materials may become self-igniting if appliedtoo thickly. Read material manufacturer’s warningsand material MSDS.
The amount of film formation and rate of crystalli-zation varies depending on the blend of ISO, thehumidity, and the temperature.
CAUTIONTo prevent cross-contamination of the equipment’swetted parts, never interchange component A (isocy-anate) and component B (resin) parts.
Pressure Relief Procedure
10 312751G
Pressure Relief Procedure
Before performing system maintenance, system pres-sure must be relieved.
Air Pressure Relief
1. Turn off and lockout main power.
2. Close day tank incoming air supply valve.
3. Disconnect pressurized air supply hose from waterseparator.
4. Bleed air pressure from system by opening thepressure relief valve on top of each day tank.
5. Ensure there is no air pressure in the tanks by look-ing at the pressure gauges mounted on the tanks.
Hydraulic Pressure Relief1. Turn off and lockout main power.
2. Open manual unloading valve by turning fully coun-terclockwise.
3. Ensure there is no hydraulic fluid pressure by look-ing at the hydraulic pressure gauge located near theautomatic unloading valve.
Chemical Line Pressure Relief1. Turn off and lockout main power.
2. Relieve air pressure. See Air Pressure Relief.
3. Close day tank outlet ball valve.
4. Ensure there is no pressure in the chemical lines bylooking at the pressure gauges mounted above themain panel.
CAUTION
Relieving air pressure in the machine means that thesupplied dry air will be replaced by moist air. Do notleave the machine exposed to moist air for more than30 minutes.
If the machine must be left without air pressure formore than 30 minutes, the day tanks must first beemptied and thoroughly flushed.
When the metering pump motors are turned off, allchemical line pressure is relieved except chemicalpressure coming from the tanks.
Repair
312751G 11
Repair
Tank Lid Gasket
Tools/Supplies Required:
• Hoist or multiple people (if an agitator is installed)
• Drop cloth
• Crescent wrench
• 3 ft. x 3 ft. air tight plastic sheet and removable tape
• Screwdriver or other prying tool
• Lithium o-ring grease
1. Turn off main power and lockout.
2. Relieve tank air pressure. See Pressure Relief Pro-cedure, page 10.
3. Use a drop cloth to set the tank lid assembly on.
4. If an agitator is installed, remove agitatormotor (G05) and gear reducer (G23).
a. While supporting the agitator motor (G05),remove four bolts (G32).
b. Remove socket head set screw (G25).
c. Remove agitator motor (G05) and gearreducer (G23) and set to the side. Leave all wireconnections in place.
5. Remove pressurized air supply tubing from tank airpressure inlet by pressing in on locking collar andpulling out the tube.
6. Use a crescent wrench to loosen all T-bolts on thetank lid in a criss-cross pattern.
7. Lift the tank lid assembly (A02) off of the tank andset on the drop cloth.
8. Use an air tight plastic sheet and removable tape tocover the day tank opening. Tape the sheet in place.
9. Use a screwdriver or other prying tool to remove thetank lid gasket (A26) from the groove on the bottomof the tank lid.
10. Apply lithium grease to the new tank lid gasket andpress the gasket into the groove.
11. Remove air tight plastic sheet and tape from tank.
If the tank includes an agitator, multiple people or ahoist will be needed to lift the tank lid and agitatorassembly out of the day tank.
G05
G23
G32G25
Agitator 1.5.5B shown,24K360 procedure is identical
ti17567a1
A02
A26
ti12248a
Repair
12 312751G
12. Ensuring the gasket (A26) stays in place, replacethe tank lid (A02) and new gasket onto the day tank.
13. Hand-tighten the T-bolts onto the lid.
14. Use a crescent wrench to tighten the T-bolts in acriss-cross pattern.
15. If an agitator is installed, re-attach the agitator motorand tighten four bolts (G32) holding agitator motor inplace.
16. Re-attach pressurized air supply tubing by pressingin on locking collar and sliding in the tube.
17. With air pressure now supplied to the tank, purgethe moist air from the tank by opening the air purgevalve on the tank lid for 60 seconds.
18. Turn on main power and run the machine for 30 min-utes to circulate material.
Level Sensor and Well
1. Turn main power off and lockout.
2. Relieve air pressure. See Pressure Relief Proce-dure, page 10.
3. Drain tanks to below level sensor well.
4. Unscrew cable (A17) from level sensorconnector (A09a).
5. Use a crescent wrench to remove level sensorwell (A10) from tank.
6. Remove the old level sensor (A09) from well (A10).
7. If the new level sensor will be used in the middle ortop of the three level sensor locations, the jumperwire (A09e) must be cut.
a. On the new level sensor, remove thescrew (A09b) connecting the upper level sensorsection (A09c) and lower level sensorsection (A09d).
b. Use a wire cutter to cut a 1/4 in. (6 mm) sectionout of the jumper wire (A09e).
c. Hold the top and bottom level sensor sectionstogether at a right angle as shown in the illustra-tion and replace screw (A09b).
8. Measure the length of the level sensor well (A10)and measure the depth of the hole in the tank wherethe well is inserted. Note these measurements asthey will be needed later.
9. Being careful to not cross-threads, thread assem-bled level sensor (A09) into well (A10) until it bot-toms out against the bottom of the well. The bottomof the level sensor will be slightly visible through thebottom of the well.
10. Apply PTFE paste and PTFE tape to the malethreads of the level sensor well (A10).
For proper level sensor function, the tip of the levelsensor well must protrude at least 1/8 in. into theday tank.
ti12245a
A17
A09a
A09b A09c
A09d
A10
A09e
A09f
CAUTION
Do not cut the jumper wire on the level sensor if thenew level sensor is being used in the bottom levelsensor location. If the jumper wire is cut and the levelsensor is to be used as the bottom level sensor, a newlevel sensor will need to be purchased.
CAUTION
In the following step, do not allow any PTFE paste ortape to cover the tip of the level sensor well. If anypaste comes in contact with the tip of the level sensorwell, thoroughly wipe clean.
Repair
312751G 13
11. Being careful to not cross-threads, thread the levelsensor well (A10) into the day tank and lightlytighten with a crescent wrench.
12. Measure the amount of the level sensor well that isvisible beyond the day tank hole, then do the follow-ing math:
13. The protrusion length must be at least 1/8 in.(3.2 mm). If not, remove the level sensor well andrestart at step 8.
14. Rotate level sensor to optimal position for wire rout-ing and connect cable (A17) to connector (A09a).
Sight TubeEach tank has a visual sight level tube that may getcloudy with age or chemical accumulation. When thishappens, replace the sight level and the sight level plas-tic connectors.
1. Turn main power off and lockout.
2. Relieve air pressure. See Pressure Relief Proce-dure, page 10.
3. Empty tanks to a few inches below the bottom of thesight level.
4. Use a plier or crescent wrench to rotate the top andbottom plastic connectors (A06) in opposite direc-tions and remove.
5. Discard sight level tube (A18) and connectors (A06,A07).
6. Use PTFE tape and PTFE paste to assemble con-nectors and tube and install onto day tank.
P = L1 - ( L2 + L3 )
P = Protrusion length (inside of day tank)L1 = Length of level sensor well (A10)L2 = Visible length of level sensor wellL3 = Length of well threads in day tank
ti12247a
A06
A07
A18
A07A06
Repair
14 312751G
Heater Thermocouple Replacement1. Turn main power off and lockout.
2. Relieve pressure. See Pressure Relief Procedure,page 10.
3. Wait for heaters to cool.
4. Remove heater shroud.
5. Disconnect thermocouple wires from inside mainpanel.
6. Feed thermocouple wires out of cabinet. Note pathas wires must be replaced in the same way.
7. See FIG. 1. Loosen ferrule nut (F11a).
8. Remove thermocouple (F11) from heaterhousing (F01), then remove thermocouplehousing (F11b). Do not remove the thermocoupleadapter (F06) unless necessary.
9. Replace thermocouple (F11). See FIG. 1.
a. Remove protective tape from thermocoupletip (F11c).
b. Apply PTFE tape and thread sealant to malethreads and tighten thermocouplehousing (F11b) into adapter (F06).
c. Push in thermocouple (F11) so tip (F11c) con-tacts heater element (F08).
d. Holding thermocouple tip (F11c) against heaterelement, tighten ferrule nut (F11a) 1/4 turn pasttight.
10. Route wires (F11d) into cabinet and thread into bun-dle as before. Reconnect wires to board.
11. Replace heater shroud.
12. Turn on both heaters simultaneously to test. Tem-peratures should rise at the same rate. If one heateris low, loosen ferrule nut (F11a) and tighten thermo-couple housing (F11b) to ensure thermocoupletip (F11c) contacts heater element (F08).
FIG. 1: Thermocouple
F11d F11
F11a
F11b
F06
F01F08
F09
F11c
Apply PTFE tape and thread sealant.
Apply 110009 thermal heatsink compound.
1
2
2
1
ti12323a
Repair
312751G 15
Flow Meter
1. Turn off main power and lockout.
2. Relieve air pressure. See Pressure Relief Proce-dure, page 10.
3. Relieve chemical pressure, ensuring that the daytank outlet ball valve is closed.
4. With a drop cloth in place and a bucket to catchmaterial, remove hose from heat exchangerinlet #1 (GB). See Heat Exchanger section onpage 29.
5. Remove reducer fitting (D03).
6. Remove hex nipple fitting (D01) and remove flowmeter from machine.
7. Use a hex key to loosen the two mountingscrews (D02l) in the sensor (D02a).
8. Note the orientation of the sensor and remove thesensor (D02a) from the flow meter body upperhousing (D02h).
9. Loosen the perimeter bolts (D02g) using a hex key.Keep the two opposing bolts near the locatingpins (D02c) engaged by a few threads to avoidstress on the shafts (D02e) and the locating pinsduring housing separation.
10. Hold the upper housing (D02h) and gently tap onthe top of the two opposing bolt heads to separatethe upper housing from the lower housing (D02j).
11. After separation, remove, clean and inspect thegears (D02d), shafts (D02e), and locating pins.
12. Clean out the o-ring groove, shaft holes, and metercavity.
13. Reinsert the gears, shafts, and locating pins. Checkfor free and easy rotation of the gears.
14. Replace the o-ring (D02b).
15. During reassembly keep the meter housings as par-allel as possible. Make sure the housings orientatedthe way they were prior to disassembly.
See manual 308778 for flow meter assembly52.7.5G.
ti12244a
D02a
D02f
D02e
D02c
D02j
D01
D02g
D02h
D02d
D02b
D03
Part 52.7.5 Shown
D02k
D02l
Note the orientation of the upper and lower housingwith respect to each other so the meter is reassem-bled correctly.
CAUTION
Do not use chisels or screwdrivers to split or pry apartthe housings. This can damage the meter bodies andmeter internal parts.
PTFE o-rings should always be replaced. Fluoro-elastomer o-rings can be reused if they are notdamaged.
Repair
16 312751G
16. Replace the washers (D02f) and bolts (D02g). Forflow meter assembly 52.7.2, torque to 30 Nm. Forflow meter assembly 52.7.5, torque to 15 Nm.
17. After reassembly, gently blow air through the meterso the gears spin. This should be clearly audiblegiven low background noise.
18. Clean any debris from the sensor pickup holes.
19. Using a hex key to tighten the mountingscrews (D02l) in the sensor, mount the sensor to theupper housing.
CAUTION
Do not force the meter housings together. Do not usea hammer or other such device. Over-tightening willnot cause damage to the meter but may fatigue thebolts and or restrict the operation if internal surfacesare not completely clean.
Repair
312751G 17
Agitator Housing(For Assembly 24K360 Only)
Disassembly
1. Remove tank lid. See steps 2 through 8 in Tank LidGasket on page 11.
2. Remove top coupling (G55).
3. Remove four socket head cap screws (G61).
4. Remove base plate assembly (G51).
5. Remove spacer (G53).
6. Remove bottom coupling (G57).
7. Use snap ring pliers to remove retaining ring (G64).
8. Remove blade assembly (G63).
9. Remove four socket head cap screws (G68), andfour lock washers (G67).
12. Remove housing (G62) along with lip seal (G60).
13. Remove gasket (G65).
Reassembly
1. Use four screws (G66) to install housing (G62) andgasket (G65) onto tank lid. Torque screws (G66) to30-45 ft-lb (41-61 N•m).
NOTE: In the following step, use a socket to press theseal into place if necessary.
2. Install seal (G60) into housing (G62) with taperedend facing down.
This procedure only applies to systems with agita-tor assembly 24K360. See FIG. 2 for agitator com-parison. If you have assembly 1.5.5B, see AgitatorHousing (For Assembly 1.5.5B Only) on page 19.
FIG. 2: Agitators
1.5.5B 24K360
ti17564a ti17565a
G63
G65
G62
G66
G54
G59
G67,G68
G57
G56
G55
G53
G51
G61
G74
G64
ti17568a
G52
G71,G72,G73Shown for ref-erence only
G69
G70
G60
G52b
Repair
18 312751G
3. With spacer (G59) installed over seal (G60), usefour screws (G68) and washers (G67) to installhousing (G54) onto other housing (G62). Torquescrews (G68) to 75-80 in-lb (8.5-9.0 N•m).
4. Insert agitator shaft (G63) through housings (G54,G62) then use snap ring pliers to install snapring (G64) onto groove in shaft (G63).
5. Rotate agitator shaft (G63) so that flat spot for setscrew is viewable through the opening in thehousing (G54).
6. Apply sealant (G75) to set screw (G74) then insertset screw into coupling (G57).
8. Verify the set screw in the coupling (G57) is locatedover the flat spot on the agitator shaft then tempo-rarily tighten the set screw.
NOTE: In the following step, be sure to installbase (G51) so that motor can be installed in the orienta-tion noted when it was removed. The opening in thebase is off-center so the gear reducer will only fit in thebase one way.
9. Place spacer (G53) onto housing (G54) then usefour screws (G61) to install base (G51) onto spacerand housing assembly. Torque screws (G61) to8-12 ft-lb (11-16 N•m).
NOTE: In the following step, the face of thecoupling (G55) should be flush with the end of the gearreducer shaft (G52).
10. Install coupling (G55) and alignment disk (G56)onto gear reducer shaft (G52). Apply sealant (G75)to set screw in coupling (G55) then tighten setscrew.
11. While rotating the agitator shaft (G63) back andforth, insert gear reducer (G52) into base (G51)then install screws and washers (G69, G70). Torquescrews (G69) to 30-45 ft-lb (41-61 N•m).
NOTE: In the following step, the agitator shaft must berotated by turning the gear reducer input sleeve shaft(G52a). Attempting to rotate the agitator shaft by rotat-ing the agitator shaft itself will not work. This is due tothe design of the gear reducer. See FIG. 3.
12. Rotate the gear reducer input sleeve shaft (G52a) toturn the agitator shaft so that the set screw (G74) inthe coupling (G57) is visible through the opening inthe housing (G54).
13. Loosen the set screw (G74) in the coupling (G57),then slide the coupling against the othercoupling (G55) and tighten the set screw (G74).
NOTE: The previous step ensures the two couplings arefully engaged.
14. Use screws and washers (G52b) to install agitatormotor (G71) onto gear reducer assembly (G52).
NOTE: The tank lid and agitator assembly weighsapproximately 100 lb (45 kg).
15. Install agitator and tank lid assembly onto tank andtighten the lid clamps.
16. Connect incoming power to the agitator motor.
17. Connect air lines to tank lid.
FIG. 3: Gear Reducer Input Sleeve Shaft
To prevent injury, use proper lifting equipment to raisethe tank lid and agitator assembly.
G52a
ti17566a
G52b
G71
G52
Repair
312751G 19
Agitator Housing(For Assembly 1.5.5B Only)
Remove Agitator Housing from Tank Lid
1. Remove tank lid. See steps 2 through 8 in Tank LidGasket on page 11.
2. Remove fitting (G22) and set lube cup assemblyaside.
3. Remove screws and washers (G32) then removegear reducer and agitator motor.
4. Remove two hex head cap screws (G01) thenremove agitator protective box.
5. Remove two hex head cap screws (G18) thenremove agitator shaft (G11) from agitatorhousing (G16).
6. Remove four socket head cap screws (G17) thenremove agitator housing (G16) from tank lid assem-bly.
Disassemble Agitator Housing
7. Secure agitator housing assembly in a vise or clampwith the wider end up as shown in the illustration.
8. Remove roll pin (H12).
9. Remove two socket head cap screws (H10).
10. Remove agitator housing cap (H08) and agitatorhousing cap gasket (H06).
11. Remove lip seal (H13) from agitator housingcap (H08) and replace with new seal.
12. Loosen and remove the clamp nut (H11).
13. Remove roller bearing (H02) from agitator housingshaft (H07).
14. Remove lower snap ring (H04), then remove theseal (H14), washer (H05), and upper snapring (H04).
This procedure only applies to systems with agita-tor assembly 1.5.5B. See FIG. 2 on page 17 for agi-tator comparison. If you have assembly 24K360,see Agitator Housing (For Assembly 24K360Only) on page 17.
If you have assembly 1.5.5B, it is recommendedthat you purchase kit 24K408 to convert to 24K360instead of repairing the agitator housing in 1.5.5B.See Agitator Conversion Kit manual 3A1931.
FIG. 4
ti12293a
G32
G32
G18
G17
G16
G11 G01
G14
G03
G22
G05G23
ti12294aH04
H14
H05
H04
H03
H01
H07
H12H10
H08
H13
H06
H11
H02
H09
Repair
20 312751G
15. Remove agitator housing shaft (H07) from assemblyand remove snap ring (H03) from agitator housingshaft (H07).
16. Remove roller bearing (H01) from agitator housingshaft (H07).
25. Replace clamp nut (H11) and tighten until tight, thenback nut off 1/4 turn and lock in place.
26. Insert a new lip seal (H13) into agitator housingcap (H08).
27. Place new agitator housing cap gasket (H06) onagitator housing (H09). Align agitator housingcap (H08) with gasket and holes in agitator housing.
28. Replace two socket head cap screws (H10) andtorque to 40-50 in-lb.
29. Replace roll pin (H12).
30. Remove assembly from vise or clamp.
Assemble Agitator Housing onto Tank Lid
31. Install two bolts (G18) to attach agitator shaft (G11)to agitator housing (G16).
32. Use a hoist to lift the tank lid assembly and agitatorassembly into the tank.
33. Tighten tank clamps.
34. Align agitator protective box and install two hexhead cap screws (G01).
35. Reinstall lube cup assembly (G22).
36. While twisting agitator shaft, install gearreducer (G23) and agitator motor (G05) onto protec-tive box and install four hex head cap screws (G32).
Auto-Fill Solenoid ValveReplacement
1. Turn off main power and lockout.
2. Relieve air pressure. See Pressure Relief Proce-dure, page 10.
3. Remove the relief nut (K10) and nippleconnector (K03) from the damaged solenoidvalve (K05).
4. Install relief nut (K10) and nipple connector (K03)onto new solenoid valve.
5. Note the location and position of the pressurized airsupply tubes and fittings (K01) then remove fromthe damaged valve.
6. Install fittings (K01) on new solenoid valve as noted.
ti12279a
K01
K03,K05,K10
K01
102
Repair
312751G 21
7. Install pressurized air supply tubes to solenoid valveas noted.
8. Remove damaged solenoid valve from tanksenclosure (102).
9. Install new solenoid valve (K05) onto tanksenclosure (102).
Boom Installation
1. Use a hoist and securely attach at least two strapsto the boom a few feet apart.
2. Carefully lift the boom above the machine, ensuringthe boom post (B07) remains straight up and down.
3. Align the boom post (B07) with the cylinder in theboom base (B08) and slowly lower the boom intothe cylinder.
4. Connect all hoses as applicable. See Hose Setupbeginning on page 22.
Metering Pumps and MeteringPump MotorsAll metering pumps and metering pump motors must bereturned to the manufacturer for repair. Attemptingrepair will void the manufacturer’s warranty.
If the boom post (B07) does not slide smoothly intothe cylinder it is because it is not straight up anddown. Slide the boom post (B07) out of the cylin-der, then straighten the post so it is straight up anddown and retry.
ti12246a
B07
B08
Hose Setup
22 312751G
Hose Setup
Tanks
Relieve air, chemical, and hydraulic pressure beforedisconnecting or connecting hoses. See PressureRelief Procedure on page 10.
With the exception of hose connections into a pipeswivel or JIC fitting, apply PTFE tape and threadsealant to all pipe fittings.
For all hose setup information shown for only oneside, opposite side setup is a mirror image to sideshown.
Ref Name Connects toAA Tank Auto-Fill Material Inlet Auto-Fill Material OutletAB Tank Material Circulation Inlet Heat Exchanger Material OutletAC Tank Material Outlet Metering Pump InletAD Tank Drain Valve Not ApplicableAE Tank Air Pressure Inlet Dry Air Pressure Supply #2
AA
AB
AC
AD
AE
ti12296a
Poly Side Tank Shown
Hose Setup
312751G 23
Metering Pumps
Ref Name Connects toBA Metering Pump Inlet Tank Material OutletBB Metering Pump Outlet Heater Inlet or Flow Meter Inlet (if
heater is not installed)BC Metering Pump Relief Outlet Heat Exchanger Inlet #2
BB
BC BAti12333a
12cc Pump, Poly Side Shown 5cc Pump, Poly Side Shown
BB
BC
BA
ti12332a
Hose Setup
24 312751G
Heaters
Ref Name Connects toKA Heater Inlet Metering Pump OutletKB Heater Outlet Flow Meter Inlet
KA
KB
ti12297a
Poly Side Heater Shown
Hose Setup
312751G 25
MixHead Hydraulic Unit
Ref Name Connects toCA L-Head Cleanout Piston Pressure - Open L-Head Cleanout Piston Open FittingCB L-Head Cleanout Piston Pressure - Close L-Head Cleanout Piston Close FittingCC MixHead Material Piston Pressure - Open MixHead Material Piston Open FittingCD MixHead Material Piston Pressure - Close MixHead Material Piston Close FittingCE Accumulator Outlet Switching Station Hydraulic Pressure Fitting #1CF Hydraulic Fluid Filter Outlet Switching Station Hydraulic Pressure Fitting #2
CA CB
CD
CC
CE
CF
1
Only installed if MixHead #1 is an L-Head.
Only installed if a second MixHead is installed.
1
2
1
2
2
ti12304a
Hose Setup
26 312751G
Top Rail without Switching Stations
Ref Name Connects toDA Circulation Valve Material Return Heat Exchanger InletDB Material Inlet from MixHead MixHead Material OutletDC Material Outlet to MixHead MixHead Material InletDD Flow Meter Inlet Heater Outlet (if installed) or Metering Pump OutletDE Air Control Valve Inlet Dry Air Pressure Supply #1
Connect lines.1
1
1
1
DA
DC DB
DDDE
ti12315a
Hose Setup
312751G 27
Top Rail with Switching Stations
1
1
1
Connect lines.1
ti12314a
EA
EB
EC
EE
ED
EF EG EH EJ EK
EL
EM
Ref Name Connects toEA MixHead #1 Seat Valve Air Supply Fittings MixHead #1 Solenoid ValveEB MixHead #2 Seat Valve Air Supply Fittings MixHead #2 Solenoid ValveEC Switching Station Hydraulic Fitting #1 Accumulator OutletED Switching Station Hydraulic Fitting #2 Hydraulic Fluid Filter OutletEE Material Outlet to MixHead #2 MixHead #2 Material InletEF MixHead #2 Material Piston Pressure - Open MixHead #2 Material Piston Open FittingEG MixHead #2 Material Piston Pressure - Close MixHead #2 Material Piston Close FittingEH MixHead #2 Cleanout Piston Pressure - Open (if
MixHead #2 is an L-Head)MixHead #2 Cleanout Piston Open Fitting
EJ MixHead #2 Cleanout Piston Pressure - Close (ifMixHead #2 is an L-Head)
MixHead #2 Cleanout Piston Close Fitting
EK Material Outlet to MixHead #1 MixHead #1 Material InletEL Material Inlet from MixHead #1 MixHead #1 Material OutletEM Material Inlet from MixHead #2 MixHead #2 Material Outlet
Hose Setup
28 312751G
MixHead Solenoid Valves
FAFB FC
FD
FE
Ref Name Connects toFA MixHead Solenoid Valve Air Pressure Inlet Dry Air Pressure Supply #1FB MixHead #2 Solenoid Valve MixHead #2 Seat Valve Fittings (through air supply tubing)FC MixHead #1 Solenoid Valve MixHead #1 Seat Valve Fittings (through air supply tubing)FD MixHead Solenoid Valve Outlets - Left Seat Valve Air Supply Fittings - TopFE MixHead Solenoid Valve Outlets - Right Seat Valve Air Supply Fittings - Bottom
ti12314a
Hose Setup
312751G 29
Heat Exchanger
Ref Name Connects toGA Heat Exchanger Outlet Tank Material Circulation InletGB Heat Exchanger Inlet #1 Circulation Valve Material ReturnGC Heat Exchanger Inlet #2 Metering Pump Relief OutletGD Water Inlet Not ApplicableGE Supplied Water Outlet Not Applicable
GA
GB
GC
GA
GD
GB
GCGE
ti12316b
Hose Setup
30 312751G
Dry Air Supply Connections
Ref Name Connects toHA Dry Air Pressure Supply #1 Air Control Valve, MixHead Solenoid Valves
(optional), Boom Actuator Air Supply Inlet (optional)HB Dry Air Pressure Supply #2 Tank Air Pressure InletHC Dry Air Pressure Supply #3 Auto-Fill Pumps
HA
HB
Connect lines.1
1
1 HC
HC
ti12317a
Hose Setup
312751G 31
Boom
Connect lines.1
1
Ref Name Connects toJA Boom Actuator Air Supply Inlet Dry Air Supply #1
JA
ti12318a
Parts
32 312751G
Parts
Fuses
◆ Fuses 13, 14, and 15 are installed only if an Iso Agitator is installed.
† Fuses 16, 17, and 18 are installed only if an Poly Agitator is installed.
Fuse Ref
Voltage/Fuse Package
24A015 24A016 24A017 24A018 24A019 24A020
FU 1 70 A 50 A 50 A 175 A 90 A 90 A
FU 2 70 A 50 A 50 A 175 A 90 A 90 A
FU 3 70 A 50 A 50 A 175 A 90 A 90 A
FU 4 20 A 10 A 10 A 50 A 30 A 30 A
FU 5 20 A 10 A 10 A 50 A 30 A 30 A
FU 6 20 A 10 A 10 A 50 A 30 A 30 A
FU 7 20 A 10 A 10 A 50 A 30 A 30 A
FU 8 20 A 10 A 10 A 50 A 30 A 30 A
FU 9 20 A 10 A 10 A 50 A 30 A 30 A
FU 10 20 A 10 A 10 A 20 A 10 A 10 A
FU 11 20 A 10 A 10 A 20 A 10 A 10 A
FU 12 20 A 10 A 10 A 20 A 10 A 10 A
FU 13◆ 2 A 2 A 2 A 2 A 2 A 2 A
FU 14◆ 2 A 2 A 2 A 2 A 2 A 2 A
FU 15◆ 2 A 2 A 2 A 2 A 2 A 2 A
FU 16† 2 A 2 A 2 A 2 A 2 A 2 A
FU 17† 2 A 2 A 2 A 2 A 2 A 2 A
FU 18† 2 A 2 A 2 A 2 A 2 A 2 A
FU 19 8 A 15 A 20 A 30 A 15 A 20 A
FU 20 8 A 15 A 20 A 30 A 15 A 20 A
FU 21 8 A 15 A 20 A 30 A 15 A 20 A
FU 22 8 A 15 A 20 A 30 A 15 A 20 A
FU 23 8 A 5 A 5 A 8 A 5 A 5 A
FU 24 8 A 5 A 5 A 8 A 5 A 5 A
FU 25 10 A 10 A 10 A 10 A 10 A 10 A
FU 26 8 A 8 A 8 A 8 A 8 A 8 A
FU 27 10 A 10 A 10 A 10 A 10 A 10 A
Parts
312751G 33
FIG. 5: Main Panel Fuses
Parts
34 312751G
Base
† Accumulator Charging Assembly 6316-18 is a rec-ommended tool used to aid in charging the accumu-lator.
--- Not for sale.
▲ Replacement Danger and Warning labels, tags, andcards are available at no cost.
Ref Part Description Qty915 --- WASHER, lock, helical, 3/8 in. 2920 --- JAR 1921 --- SCREW, pan head machine, 10-32 x 3/8 in. 2922 --- TRAY 1923 --- PUMP 1928 --- SCREW, 1/4-20 x 3/4 hex head cap screw 2929 --- WASHER, 1/4 flat 2930 --- WASHER, sae, helical, 1/4 in. 2
920
921
923915
929, 930928922
ti12251a
Parts
52 312751G
Non-Jacketed Tanks
--- Not for sale.
Tank Lid Assembly
--- Not for sale.
Tank Outlet Assembly
--- Not for sale.
Ref Part Description QtyA01 --- FITTING, swivel, 3/4nps x
G72▲ 10673-1 LABEL, high voltage warning 1G73 L0437 LABEL, motor rotation arrow 1G74 --- SCREW, socket head set,
5/16-18 x 0.751
G75 113500 ADHESIVE, anaerobic,0.017 fl oz, 0.5 ml
1
G63
G65
G62
G66
G54
G59
G67,G68
G57
G56
G55
G53
G51
G61
G74
G64
ti17568a
G52
G71,G72,G73Shown for ref-erence only
G69
G70
G60
Parts
64 312751G
Agitator Housing, Part M638
--- Not for sale.
If you have assembly 1.5.5B, it is recommendedthat you purchase kit 24K408 to convert to 24K360instead of repairing this agitator housing M638.See Agitator Conversion kit manual 3A1931.
Graco Standard WarrantyGraco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects inmaterial and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warrantypublished by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined byGraco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s writtenrecommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faultyinstallation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution ofnon-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment withstructures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation ormaintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification ofthe claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returnedto the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs willbe made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITEDTO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental orconsequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOTMANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject tothe warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of thesewarranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, orthe furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, thenegligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERSThe Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que larédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suitede ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco InformationFor the latest information about Graco products, visit www.graco.com.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.Toll Free: 1-800-746-1334 or Fax: 330-966-3006
All written and visual data contained in this document reflects the latest product information available at the time of publication.Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 312751
Graco Headquarters: MinneapolisInternational Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441Copyright 2009, Graco Inc. is registered to ISO 9001