20909349-TM-9-1005-338-13-P-Mossberg-500-and-590

ARMY TM 9-1005-338-13&P

TECHNICAL MANUAL UNIT AND DIRECT SUPPORT MAINTENANCE

(INCLUDING REPAIR PARTS AND SPECIAL TOOLS LIST)

FOR

MOSSBERG 12-GAUGE SHOTGUN, MODEL 500 (1005-01-295-1832)

AND

MOSSBERG 12-GAUGE SHOTGUN, MODEL 590

(1005-01-251-8578)

2MB0001

MODEL 500

2MB0002

MODEL 590 SUPERCEDURE NOTICE: This Technical Manual supersedes TM 9-1005-303-14, dated 29 July 1968, with all changes.

HEADQUARTERS, DEPARTMENTS OF THE ARMY

MAY 2005

TM 9-1005-338-13&P WARNING SUMMARY Be sure to clear your weapon before disassembling, cleaning, inspecting, transporting or storing. Make certain weapon is cleared and that there is no obstruction in the barrel or chamber. Before starting an inspection, be sure to clear the weapon. Do not actuate the trigger until the weapon has been cleared. Inspect the chamber to be sure that it is empty, and check to see that there are no obstructions in the barrel. Do not pull trigger and allow hammer to fall when trigger assembly is removed form receiver. Personal injury or damage to trigger assembly may result. To avoid injury to eyes, use care when removing and installing spring loaded parts. Cleaning solvent is FLAMMABLE and TOXIC and must be kept away from open flames and used in a well-ventilated area. Use of rubber gloves is necessary to protect the skin when washing weapons parts. Appropriate eye protection is recommended when cleaning your weapon or its parts. For additional first aid data, see FM 4-25.11. Refer to PAM 385-64 for information on weapons, ammunition, and related publications. During immediate action make certain the shotgun is pointed in a safe direction at all times. During remedial action make certain the shotgun is pointed in a safe direction at all times.

a/b blank http://www.emilitarymanuals.com

TM 9-1005-338-13&P LIST OF EFFECTIVE PAGES NOTE: Zero in this column indicates an original page or work package. Dates of issue for original manual is: 15 May 2005

Page/WP No. *Change No. Page/WP No. *Change No. Title 0 WP 0031 (2 pgs) 0 Warning Summary 0 Chap 5 title page i-v/vi blank 0 WP 0032 (2 pgs) 0 Chap 1 title page 0 WP 0033 (4 pgs) 0 WP 0001 (4 pgs) 0 WP 0034 (2 pgs) 0 WP 0002 (4 pgs) 0 WP 0035 (8 pgs) 0 WP 0003 (2 pgs) 0 WP 0036 (4 pgs) 0 Chap 2 title page 0 WP 0037 (4 pgs) 0 WP 0004 (2 pgs) 0 WP 0038 (4 pgs) 0 WP 0005 (4 pgs) 0 WP 0039 (2 pgs) 0 WP 0006 (2 pgs) 0 WP 0040 (4 pgs) 0 WP 0007 (2 pgs) 0 WP 0041 (4 pgs) 0 WP 0008 (2 pgs) 0 WP 0042 (2 pgs) 0 WP 0009 (2 pgs) 0 WP 0043 (2 pgs) 0 WP 0010 (2 pgs) 0 WP 0044 (2 pgs) 0 WP 0011 (4 pgs) 0 WP 0045 (2 pgs) 0 WP 0012 (2 pgs) 0 WP 0046 (2 pgs) 0 WP 0013 (2 pgs) 0 WP 0047 (2 pgs) 0 WP 0014 (6 pgs) 0 INDEX-1- 0 WP 0015 (2 pgs) 0 INDEX-4/blank WP 0016 (2 pgs) 0 WP 0017 (2 pgs) 0 Chap 3 title page 0 WP 0018 (2 pgs) 0 WP 0019 (2 pgs) 0 WP 0020 (4 pgs) 0 WP 0021 (4 pgs) 0 WP 0022 (2 pgs) 0 WP 0023 (2 pgs) 0 WP 0024 (4 pgs) 0 WP 0025 (4 pgs) 0 WP 0026 (2 pgs) 0 Chap 4 title page 0 WP 0027 (4 pgs) 0 WP 0028 (4 pgs) 0 WP 0029 (2 pgs) 0 WP 0030 (2 pgs) 0

A/B blank http://www.emilitarymanuals.com

TM 9-1005-338-13&P

http://www.emilitarymanuals.com

TM 9-1005-338-13&P TECHNICAL MANUAL No. TM 9-1005-338-13&P

HEADQUARTERS,DEPARTMENT OF THE ARMY

WASHINGTON D.C 15 MAY 2005

TECHNICAL MANUAL UNIT AND DIRECT SUPPORT MAINTENANCE

(INCLUDING REPAIR PARTS AND SPECIAL TOOLS LIST)

FOR

MOSSBERG 12-GAUGE SHOTGUN, MODEL 500 (1005-01-295-1832)

AND

MOSSBERG 12-GAUGE SHOTGUN, MODEL 590

(1005-01-251-8578)

REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS You can help improve this publication. If you find any mistakes or if you know of a way to improve the procedures, please let us know. Submit your DA Form 2028 (Recommended Changes to Equipment Technical Publications), through the Internet, on the Army Electronic Product Support (AEPS) website. The Internet address is http://aeps.ria.army.mil. If you need a password, scroll down and click on “ACCESS REQUEST FORM”. The DA Form 2028 is located in the ONLINE FORMS PROCESSING section of the AEPS. Fill out the form and click on SUBMIT. Using this form on the AEPS will enable us to respond quicker to your comments and better manage the DA Form 2028 program. You may also mail, fax, or e-mail your letter or DA Form 2028 direct to: AMSTA-LC-CI/ TECH PUBS, TACOM-RI, 1 Rock Island ARSENAL, IL 61299-7630. The e-mail address is [email protected]. The fax number is DSN 793-0726 or commercial (309) 782-0726. This manual supersedes TM 9-1005-303-14, dated 29 July 1968, including all changes.

i


TM 9-1005-338-13&P

This page intentionally left blank.

ii http://www.emilitarymanuals.com

TM 9-1005-338-13&P

TABLE OF CONTENTS WP Sequence No. WARNING SUMMARY HOW TO USE THIS MANUAL CHAPTER 1 – GENERAL INFORMATION

Chapter Overview........................................................................................................... 0001 00 Maintenance, Forms, Records, and Reports ................................................................. 0001 00 Reporting Equipment Improvement Recommendations (EIR)....................................... 0001 00 Corrosion Prevention and Control (CPC)....................................................................... 0001 00 Destruction of Materiel to Prevent Enemy Use .............................................................. 0001 00 Preparation for Storage and Shipment........................................................................... 0001 00 List of Abbreviations and Acronyms............................................................................... 0001 00 Quality of Material .......................................................................................................... 0001 00 Safety, Care and Handling ............................................................................................. 0001 00 Nuclear, Biological, an Chemical (NBC) ........................................................................ 0001 00 Equipment Characteristics, Capabilities, and Features ................................................. 0002 00 Location and Description of Major Components ............................................................ 0002 00 Differences Between Models.......................................................................................... 0002 00 Equipment Data.............................................................................................................. 0002 00 Theory of Operation ....................................................................................................... 0003 00

CHAPTER 2 – OPERATOR INSTRUCTIONS Operator’s Controls and Indicators................................................................................. 0004 00 Operation Under Usual Conditions –

Operating Procedures.............................................................................................. 0005 00 Stoppage or Stuck Cartridge ................................................................................... 0006 00 Immediate Action ..................................................................................................... 0007 00 Remedial Action....................................................................................................... 0008 00 Authorized Ammunition............................................................................................ 0009 00

Operation Under Unusual Conditions ............................................................................ 0010 00 Troubleshooting Procedures, Operator .......................................................................... 0011 00 Preventive Maintenance Checks and Services – Operator (Introduction) ..................... 0012 00 Preventive Maintenance Checks and Services - Operator ............................................ 0013 00 Operator Maintenance -

Fielding Stripping ..................................................................................................... 0014 00 Cleaning................................................................................................................... 0015 00 Lubrication ............................................................................................................... 0016 00

Function Check............................................................................................................... 0017 00

CHAPTER 3 – UNIT MAINTENANCE Service Upon Receipt of Materiel................................................................................... 0018 00 Unit Maintenance Instructions ........................................................................................ 0019 00 Troubleshooting Procedures, Unit Maintenance............................................................ 0020 00 Preventive Maintenance Checks and Services – Unit Maintenance.............................. 0021 00 Unit Maintenance of:

Mossberg 12-Gauge Shotgun, Model 500 (P/N MOD500)...................................... 0022 00 Mossberg 12-Gauge Shotgun, Model 590 (P/N 52660) .......................................... 0022 00 Fore End Assembly (P/N MOSS-05) ....................................................................... 0023 00 Barrel Assembly (P/N 3907P).................................................................................. 0024 00 Barrel Assembly (P/N 41758) .................................................................................. 0024 00 Stock, Gun, Shoulder (P/N 14762MIL) .................................................................... 0025 00 Pistol Grip Assembly (P/N 95000) ........................................................................... 0026 00

iii http://www.emilitarymanuals.com

TM 9-1005-338-13&P

TABLE OF CONTENTS (cont) WP Sequence No. CHAPTER 4 – DIRECT SUPPORT MAINTENANCE

Troubleshooting Procedures, Direct Support Maintenance............................................0027 00 Direct Support Maintenance of:

Receiver Assembly (P/N 10171MIL and M590L) .....................................................0028 00 Bolt Assembly (P/N 6706P)......................................................................................0029 00

Illustrated List of Manufactured Items.............................................................................0030 00 Ammunition Care and Usage..........................................................................................0031 00

CHAPTER 5 – SUPPORT INFORMATION

References......................................................................................................................0032 00 Maintenance Allocation Chart (MAC) .............................................................................0033 00 Repair Parts and Special Tools List (introduction) .........................................................0035 00 Repair Parts and Special Tools List for:

Mossberg 12-Gauge Shotgun, Model 500 (P/N MOD500) ......................................0036 00 Mossberg 12-Gauge Shotgun, Model 590 (P/N 52660)...........................................0036 00 Receiver Assembly (P/N 10171MIL and M590L) .....................................................0037 00 Safety Assembly (NPN)............................................................................................0037 00 Barrel Assembly (P/N 3907P) ..................................................................................0038 00 Barrel Assembly (P/N 41758)...................................................................................0038 00 Fore End Assembly (P/N MOSS-05)........................................................................0039 00 Bolt Assembly (P/N 6706P)......................................................................................0040 00 Stock, Gun, Shoulder (P/N 14762MIL).....................................................................0041 00 Pistol Grip Assembly (AAL) (P/N 95000) .................................................................0042 00

Cross Reference Index – Part Number ..........................................................................0043 00 Cross Reference Index – National Stock Number..........................................................0044 00 Components of the End Item and Basic Issue Items......................................................0045 00 Additional Authorized List (AAL) .....................................................................................0046 00 Expendable and Durable Items List................................................................................0047 00

iv http://www.emilitarymanuals.com

TM 9-1005-338-13&P HOW TO USE THIS MANUAL GENERAL. In order to use this manual efficiently, there are several things you need to know.

• All references in the manual are to work packages or to another manual. • Whenever the male gender is mentioned (i.e., crewman, repairman) in the manual, it also

pertains to females. • Procedures apply to all models unless otherwise noted.

INDEXES. This manual is organized to help you quickly find the information you need. There are several useful indexes.

• Table of Contents. Lists in order all chapters, work packages, and appendixes. • Nomenclature Cross Reference List. Gives an alphabetical list of the common names that

are substituted for the official nomenclature in the manual. • Chapter Overviews. Summarize material covered in the chapter. • Troubleshooting Symptom Index. Lists in alphabetical order parts of the weapon with

possible malfunctions. References work package pages of the troubleshooting table. • Alphabetical Index. Located at the end of the manual. An extensive subject index for

everything in the manual. It gives work package references. MAINTENANCE PROCEDURES. There are two maintenance chapters, one for unit and one for direct support. Each has an initial setup containing a list of the following things you will need in order to do your maintenance task.

• Tool and Special Tools. List tool kit and tools not found in your tool kit. • Material/Parts. Lists expendable/durable materials and 100% replaceable parts. A part

number or work package reference follows each material or part. If more than one part is needed, the quantity needed will follow the part number or reference.

• References. List other publications containing necessary information. • Equipment Condition. Lists conditions to be met before starting a procedure. The reference

following the condition is the work package reference to instructions for setting up the condition.

• Maintenance Procedures. Step-by-step illustrated procedures for maintenance authorized by the Maintenance Allocation Chart (MAC), WP 0034 00.

v/vi blank http://www.emilitarymanuals.com

TM 9-1005-338-13&P


CHAPTER 1

GENERAL INFORMATION http://www.emilitarymanuals.com

TM 9-1005-338-13&P 0001 00 GENERAL INFORMATION CHAPTER OVERVIEW. This chapter contains general information, equipment description and data, and principles of operation for the shotgun. SCOPE Type of Manual: Operator, Unit, and Direct Support Maintenance Equipment Number and Model Number: Mossberg12- Gauge Shotgun Model 500 and Mossberg 12- Gauge Shotgun Model 590. Purpose of Equipment: To provide repeating weapon fire for offensive and defensive purposes. MAINTENANCE FORMS, RECORDS, AND REPORTS. Department of the Army forms and procedures used for equipment maintenance will be those prescribed by DA PAM 738-750, Functional users Manual for the Army Maintenance Management System (TAMMS). Marine Corps users refer to TM 4700-15/1, Ground Equipment Record Procedures. REPORTING EQUIPMENT IMPROVEMENT RECOMMENDATIONS (EIR). If your shotgun needs improvement, let us know. Send us and EIR. You, the user, are the only one who can tell us what you don’t like about your equipment. Let us know why you don’t like the design or performance. Put in an SF 368 (Product Quality Deficiency Report). Mail it to Commander, Armament Research, Development and Engineering Center, ATTN: AMSTA-AR-QAW-A (R), 1 Rock Island Arsenal, Rock Island, IL 61299-7300. We’ll send you a reply CORROSION PREVENTION AND CONTROL (CPC). Corrosion prevention and control of material is a continuing concern. It is important that any corrosion problems with this item be reported so that the problem can be corrected and improvements can be made to prevent the problem in future items. While corrosion is typically associated with rusting of metals, it can also include deterioration of other materials such as rubber and plastic. Unusual cracking, softening, swelling, or breaking of these materials may be a corrosion problem. If a corrosion problem is identified, it can be reported using SF 368 Product Quality Deficiency Report. Use of key words such as “corrosion”, “rust”, “deterioration”, or “cracking” will assure that the information is identified as a CPC problem. The form should be submitted to Commander, Armament Research, Development and Engineering Center, ATTN: AMSTA-AR-QAW-A/Customer Feed back Center, 1 Rock Island Arsenal, Rock Island, IL 61299-7300. DESTRUCTION OF MATERIEL TO PREVENT ENEMY USE. Procedure and materials used for the destruction of the machine gun to prevent enemy use will be found in TM 750-244-7. PREPARATION FOR STORAGE AND SHIPMENT. Not applicable.

0001 00-1 http://www.emilitarymanuals.com

TM 9-1005-338-13&P 0001 00 GENERAL INFORMATION (cont) LIST OF ABBREVIATIONS AND ACRONYMS This list includes nomenclature cross-references used in this manual.

Common Name Official Name Action lock .................................................. Action bar lock Action slide assembly ................................ Fore End Tube Assembly;

Grip Assembly; Slide Arm Extension

Barrel .......................................................... Shotgun barrel Barrel Assembly ......................................... Barrel and Bayonet Band Assembly;

Barrel Group; Shotgun Barrel

Butt Plate .................................................... Recoil Pad; Shoulder Butt Plate

Cartridge Extractor Pin ............................... Cartridge Extractor Cartridge Extractor Spring .......................... Cartridge Extractor Cartridge Follower ...................................... Magazine Follower Firing Pin Collar .......................................... Tool Holder Cutter Bit Firing Pin Retaining Pin .............................. Cartridge Extractor Firing Pin Extractor Spring.......................... Fire Pin Extractor Fore End Assembly .................................... Fore End Group Front Swivel Assembly ............................... Special Cap Magazine Cap............................................. Machine screw;

Tube Cap Magazine Spring......................................... Helical Compression Spring Magazine Tube........................................... Metal tube Assembly;

Shotgun Magazine Tube

Rear Swivel Assembly................................ Small Sling Swivel; Special Cap

Receiver Assembly..................................... Receiver and Magazine Group Shotgun Slide Grip ..................................... Gun Fore End Stock;

Shotgun Grip Slide Tube Nut ............................................ Grip Adapter;

Retaining Ring Extension; Tube Cap

Stock........................................................... Buttstock Assembly; Shoulder Gun Stock (233103; 7440)

Stock Assembly .......................................... Shoulder Gun Stock (30515); Stock

Trigger Assembly........................................ Trigger guard Assembly; Trigger housing Assembly; Trigger plate Assembly


TM 9-1005-338-13&P 0001 00 QUALITY OF MATERIAL Material used for replacement, repair, or modification must met the requirements of this manual. If the quality of material requirements is not stated in the manual, the material must meet the requirements of the drawings, standards, specifications, or approved engineering change proposals applicable to the subject equipment. SAFETY, CARE AND HANDLING To ensure safety, read the warning page at the front of this manual. Pay close attention to the warnings and cautions that appear in this manual where special care and attention are required. For ammunition care and handling, refer to PAM 385-64. NUCLEAR, BIOLOGICAL, AND CHEMICAL (NBC) General procedures can found in FM 3-4, FM 3-5, and 3-87.

0001 00-3/4 blank http://www.emilitarymanuals.com

TM 9-1005-338-13&P 0001 00


TM 9-1005-338-13&P 0002 00 EQUIPMENT DESCRIPTION AND DATA EQUIPMENT CHARATERISTICS, CAPABLITIES, AND FEATURES. The shotgun is manually operated, repeating, magazine fed, shoulder fired weapon. LOCATION ANS DESCRIPTION OF MAJOR COMPONENTS

2MB0003

1

2

6 5

3

4

M590 BARREL

STOCK ASSEMBLY (1) - The stock is an extension of the receiver group and provides a support to the shoulder fired weapon. SHOTGUN BARREL (2) - Barrel provides path for projectiles. The front sight serves as an aiming device. TRIGGER HOUSING ASSEMBLY (3) - The trigger guard assembly houses the components required to provide locking, initial feeding, loading, firing, and safety functions of the weapon. GUN FORE END (4) - The slide arm extension is used to open and close the breech bolt group, permitting loading and firing of the weapon and extraction and ejection of spent cartridges. BOLT ASSEMBLY (5) - The bolt assembly feeds and locks the round in the chamber. The firing pin detonates the primer to fire the weapon. The fired round is removed from the chamber by the extractor. RECEIVER ASSEMBLY (6) - Receiver and magazine group. The magazine tube serves as a retainer for the fore end assembly and provides a storage area for the cartridges. The receiver houses the cartridge ejector and serves as support for all major groups and assemblies of the weapon. DIFFERENCES BETWEEN MODELS The Mossberg Model 590 has a detachable heat shield.


TM 9-1005-338-13&P 0002 00 EQUIPMENT DESCRIPTION AND DATA (cont) EQUIPMENT DATA

MOSSBERG, MODEL 500

Gauge of bore...................................................................................................12 gauge Choke ...............................................................................................................Cylinder Type of action ...................................................................................................Pump Type of firing mechanism ................................................................................. Internal hammer Magazine capacity............................................................................................5 rounds Total capacity (with cartridge in chamber)........................................................6 rounds Operation ..........................................................................................................Manual Cooling..............................................................................................................Air Length (Barrel)..................................................................................................18.5 in. Length (Shotgun) ..............................................................................................39.5 in. Weight of shotgun (approx) ..............................................................................7.0lb (3.2kg) Ammunition.......................................................................................................12 gauge, 2-3/4in. - No.00 buckshot or Chilled shot as authorized Safety................................................................................................................Top of receiver


TM 9-1005-338-13&P 0002 00

MOSSBERG, MODEL 590 Gauge of bore .......................................................................................................... 12 gauge Choke....................................................................................................................... Cylinder Type of action .......................................................................................................... Pump Type of firing mechanism......................................................................................... Internal hammer Type of magazine .................................................................................................... Tubular Magazine capacity (3 in. cartridges) ........................................................................ 7 rounds Total capacity (with cartridge in chamber) ............................................................... 8 rounds Operation ................................................................................................................. Manual Cooling..................................................................................................................... Air Length (Barrel) ......................................................................................................... 20 in. (51cm) Length (Shotgun) (approx.)...................................................................................... 40.5 in (102.9 cm) Weight of unloaded shotgun (approx.)..................................................................... 8.0 lbs (3.6 kg) Ammunition .............................................................................................................. 12 gauge, 2 3/4 in. - No. 00 buckshot or Chilled shot as authorized Safety ....................................................................................................................... Top of receiver


TM 9-1005-338-13&P 0002 00


TM 9-1005-338-13&P 0003 00 THEORY OF OPERATION Pulling the trigger, sliding the fore end to the rear to open the action, and sliding the fore end forward again to close the action complete the entire operation of the shotgun. The fore end is mounted on double action bars and fully controlled by the operator. With the magazine fully loaded and one shell in the barrel chamber locked up, the shotgun is ready to fire.


TM 9-1005-338-13&P 0003 00


CHAPTER 2

OPERATOR INSTRUCTIONS http://www.emilitarymanuals.com

TM 9-1005-338-13&P 0004 00 OPERATOR’S CONTROLS AND INDICATORS

NOTE Controls/indicators function the same on both Mossberg Model 500 and Model 590.

ACTION LOCK LEVER This lever (1) allows the action to be unlocked without engaging the trigger.

1

2MB0004

WARNING If red is shown to the rear of the safety switch, weapon can be fired. Safety “ON” (safety switch to the rear) indicates “SAFE”, safety “OFF” (safety switch forward) indicates “FIRE”.

SAFETY When in the rear (ON) position, the safety (2) prevents the firing of the weapon.

2

2MB0005 TRIGGER The trigger (3) controls the firing of the weapon.

2MB0006

3


TM 9-1005-338-13&P 0004 00 OPERATOR’S CONTROLS AND INDICATORS (cont) FORE END The fore end (4) is found forward of the receiver below barrel. Slide the action forward and rearward to chamber live cartridges and eject spent cartridges.

NOTE Model M500 shown for illustration purposes.

2MB0007

4


TM 9-1005-338-13&P 0005 00 OPERATION UNDER USUAL CONDITIONS – OPERATING PROCEDURES LOADING

NOTE The safety will be found on the top of the receiver.

Move safety switch (1) fully rearward to “SAFE” position. Assure fore end (2) is fully forward.

1

2

2MB0008 Turn shotgun over and insert cartridge (3) into magazine (4) until magazine is fully loaded.

3/4

2MB0009 Depress action lock (5) and move fore end (2) fully to the rear and forward again, chambering the first round. Another round can be added to the magazine if desired.

2MB0010

5

2


TM 9-1005-338-13&P 0005 00 OPERATION UNDER USUAL CONDITIONS – OPERATING PROCEDURES (cont) FIRING Point shotgun down range in a safe direction. Move safety switch (1) forward to fire position. Aim and fire by pulling the trigger (6). Slide fore end (2) back and forth once to close action and load cartridge into chamber. Repeat to continue firing.

1

2

6

2MB0011 REMOVING CARTRIDGES FROM MAGAZINE Move safety switch (1) fully rearward to “SAFE” position. Assure fore end (2) is fully forward. Turn shotgun over, depress shell latch (7), allowing cartridges (8) to slide out of magazine tube. Remove cartridge from shotgun. Repeat until magazine is empty.

8

2MB0012

1

7

2


TM 9-1005-338-13&P 0005 00 REMOVING CARTRIDGES FROM CHAMBER Move safety switch (1) fully rearward to “SAFE” position. Push in action lock (6) and slide fore end (2) to the rear. Catch ejected cartridge (s) from chamber. Visually inspect the carrier for cartridge(s). If a cartridge is present on carrier, rotate shotgun to the right and catch cartridge from the ejection port.

1

2

6

2MB0011

END OF WORK PACKAGE


TM 9-1005-338-13&P 0005 00


TM 9-1005-338-13&P 0006 00 OPERATION UNDER USUAL CONDITIONS – STOPPAGE OR STUCK CARTRIDGE STOPPAGE If stoppage occurs when firing:

• Put the weapon on safe and cycle the weapon.

• Observe if cartridge has been ejected; check to see if cartridge is stuck in the weapon. If cartridge is stuck in the weapon perform stuck cartridge procedures.

• Check to see if weapon is out of ammunition, reload and continue firing.

STUCK CARTRIDGE If stuck cartridge occurs during firing:

• Put the weapon on safe.

• Unload the weapon (WP 0005 00) keeping the weapon pointed in a safe direction.

• Insert a cleaning rod down the muzzle end of barrel and push the stuck cartridge out f the chamber. Be ready to catch the round.

• Check the primer of the ejected cartridge:

If the primer has been dented by the firing pin (light strike) dispose of the cartridge in accordance with local procedures.

If there is no indication of round misfire, reload and try to fire round.

• If the problem continues notify the unit armor for further assistance.

END OF WORK PACKAGE


TM 9-1005-338-13&P 0006 00


TM 9-1005-338-13&P 0007 00 OPERATION UNDER USUAL CONDITIONS – IMMEDIATE ACTION Immediate Action is the action performed immediately by the firer any time there is an unscheduled or unanticipated interruption of the shotgun operation. Immediate action should be practiced to the point that it occurs as a reflex action.

WARNING During immediate action make certain the shotgun is pointed in a safe direction at all times.

To perform immediate action:

• Pull the fore-end rearward.

• Check the ejection port, if a cartridge is ejected push the fore-end forward and attempt to fire again.

• If the weapon still fails to fire, perform remedial action (WP 0008 00).

END OF WORK PACKAGE


TM 9-1005-338-13&P 0007 00


TM 9-1005-338-13&P 0008 00 OPERATION UNDER USUAL CONDITIONS – REMEDIAL ACTION Remedial Action is the action performed to remedy a problem and place the shotgun back into operation after immediate action has been performed and proves ineffective.

WARNING During remedial action make certain the shotgun is pointed in a safe direction at all times.

To perform remedial action:

• Clear the shotgun (WP 0005 00).

• Check the chamber and remove any type of obstruction caused by an empty or ruptured case, live round or forging matter (WP 0006 00).

• Reload magazine tube (WP 0005 00).

• Chamber a cartridge (WP 0005 00).

• Attempt to fire (WP 0005 00).

• Notify unit armorer if remedial action fails to correct problem.


TM 9-1005-338-13&P 0008 00


TM 9-1005-338-13&P 0009 00 OPERATION UNDER USUAL CONDITIONS – AUTHORIZED AMMUNITION

WARNING This is the only ammunition authorized for use in your shotgun. If it is not shown, it is not authorized. Ammunition that fails to fire will be disposed of by authorized procedures.

Table 1. Authorized Ammunition for

Mossberg Model 500 and Model 590 Shotguns

MODEL

CAPACITY (with one in chamber)

LETHAL

NON-LETHAL

IDENTIFICATION

500 and 590

6/5 8

# 00 BUCKSHOT M162 # 7 1/2 SHOT # 9 SHOT

M1012 Point Control M1013 Crowd Dispersal

LETHAL -2-3/4” NON-LETHAL – 3”

500 and 590

6/7 8

M1030 Breeching Cartridge

LETHAL -2-3/4”

500 and 590

6 8

MK242 MOD 0 Dummy Cartridge

INERT –2 3/4”

Protect ammunition from mud, sand, and water. If the ammunition gets wet or dirty, wipe it off at once with a clean, dry, rag (item 7, WP 0045 00). Wipe off light corrosion as soon as it is discovered. Turn in heavily corroded cartridges. Do not expose ammunition to the direct rays of the sun. If the powder is hot, excessive pressure may develop when the weapon is fired. Do not oil or grease ammunition. Dust and other abrasives that collect on greasy ammunition may cause damage to the operating parts of the machine gun. Moreover, oiled cartridges produce excessive chamber pressure. Do not fire dented cartridges or otherwise defective rounds. For information on care, handling, preservation and packing of ammunition refer to WP 0031 00.

END OF WORK PACKAGE


TM 9-1005-338-13&P 0009 00


TM 9-1005-338-13&P 0010 00 OPERATION UNDER UNUSUAL CONDITIONS EXTREME COLD (BELOW 32O F (OO C)

NOTE If weapons are exposed to temperatures changing quickly from warm to cold, condensation may form causing rusted parts

If weapons are exposed to conditions that cause condensation, wipe condensation from exposed metal surfaces, and lubricate weapon. Ensure weapon function after exposure to extreme weather changes. HOT AND HUMID OR SALTY AIR Inspect shotgun frequently for rust. Lightly oil metal parts. HOT AND DRY Clean shotgun daily (or more often if needed). In sandy or dusty areas, wipe shotgun free of oil to prevent sand and dust from collecting on the surface and on moving parts. IMMERSION IN WATER Drain water out of shotgun. Unload shotgun. If possible, wipe ammunition dry. Field strip, wipe dry, and lube shotgun as soon as possible. Clean and lubricate weapon, notify unit maintenance.

END OF WORK PACKAGE


TM 9-1005-338-13&P 0010 00


TM 9-1005-338-13&P 0011 00 OPERATOR TROUBLESHOOTING PROCEDURES This work package contains unit-troubleshooting information for locating and correcting most of the operating troubles that may develop in the shotgun. Each malfunction for a part, assembly, or subassembly is followed by a list of tests or inspections, which will help you to determine corrective actions to take. You should perform the tests/inspections and corrective actions in the order listed. This manual cannot list all possible malfunctions that may occur, nor all tests or inspections and corrective actions. If a malfunction is not listed (except when malfunction or cause is obvious) or is not corrected by listed corrective actions, notify direct support maintenance. TROUBLESHOOTING PROCEDURES Refer to symptom index or troubleshooting table for malfunctions, tests/inspections, and corrective action.

SYMPTOM INDEX Troubleshooting Procedure Work Package/Page Ammunition double feeds ..................................................................................................... 0011 00-4 Cartridge fails to extract or eject ........................................................................................... 0011 00-4 Operation is sluggish ............................................................................................................ 0011 00-3 Shotgun fails to load or feed ................................................................................................. 0011 00-3 Shotgun will not fire............................................................................................................... 0011 00-2


TM 9-1005-338-13&P 0011 00 OPERATOR TROUBLESHOOTING PROCEDURES (cont)

Table 1. Operator Troubleshooting Procedures SYMPTOM Shotgun will not fire.

MALFUNCTION Safety is in rearward “SAFE” position.

CORRECTIVE ACTION Move safety to forward “FIRE” position.

MALFUNCTION No ammunition in chamber or magazine.

CORRECTIVE ACTION Load shotgun.

MALFUNCTION Chamber is empty.

CORRECTIVE ACTION Pump cartridge into chamber.

MALFUNCTION Ammunition is faulty.

CORRECTIVE ACTION Remove defective cartridges and use new ammunition.

MALFUNCTION Firing pin and/or extractors are burred, excessively worn or broken.

CORRECTIVE ACTION Notify unit maintenance.

MALFUNCTION Bolt assembly will not slide forward by pushing fore end forward.

CORRECTIVE ACTION If fore end will not slide forward, notify unit maintenance.


TM 9-1005-338-13&P 0011 00 SYMPTOM Shotgun fails to load or feed.

MALFUNCTION Obstruction in chamber.

CORRECTIVE ACTION Remove obstruction in chamber.

MALFUNCTION Foreign material in magazine tube and in the left and right slide arm supports of the action slide.

CORRECTIVE ACTION Remove foreign matter. Clean and lube weapon.

SYMPTOM Operation is sluggish.

MALFUNCTION Weapon is dirty, lacks of lubrication, and/or has carbon or burrs.

CORRECTIVE ACTION Clean and lubricate shotgun.

SYMPTOM Ammunition double feeds.

MALFUNCTION Cartridge stop or cartridge interrupter bent or missing.


SYMPTOM Cartridge fails to extract or eject.

MALFUNCTION Extractor or ejector are burred, broken or missing.


END OF WORK PACKAGE


TM 9-1005-338-13&P 0011 00


TM 9-1005-338-13&P 0012 00 PREVENTIVE MAINTENANCE CHECKS AND SERVICES - OPERATOR GENERAL This work package applies to all shotguns found in this manual. Your PMCS table has been provided so you can keep your equipment in good operating condition and ready for its primary use. Refer to the chapter for your mount for specific requirements. INTRODUCTION TO PMCS TABLE WARNINGS AND CAUTIONS Always observe WARNINGS and CAUTIONS appearing in your PMCS table BEFORE, DURING, and AFTER you operate your equipment. The warning and cautions appear before certain procedures. You must observe these WARNINGS and CAUTIONS to prevent injury to yourself and others or to prevent your equipment from being damaged. EXPLANATION OF TABLE ENTRIES Item Number Column. Numbers in this column are for reference. When completing DA Form 2404, Equipment Inspection and Maintenance Worksheet, include the item number for the check/service indicating a fault. Item numbers also appear in the order that you must do checks and services for the intervals listed. Interval Column. This column tells you when you must do the procedure in the procedure column. BEFORE procedures must be done before you operate or use the equipment for its intended mission. DURING procedures must be done during the time you are operating or using the equipment for its intended mission. AFTER procedures must be done immediately after you have operated or used the equipment. Man-hour Column. This column shows man-hours required to complete all prescribed lubrication services, stated to the nearest tenth of an hour. Item to be Checked Column. This column provides the location and the item to be checked or serviced. Procedure Column. This column gives you the procedure you must do to check or service the item listed in the Item to Check/Service column to determine if the equipment is ready or available to perform its intended mission or for operation. You must do the procedure at the time stated in the interval column. “Not Fully Mission Capable If:” Column. Information in this column tells you what faults will keep your equipment from being capable of performing its primary mission. If you make check and service procedures that show faults listed in this column, do not operate the equipment. Follow standard operating procedures for maintaining the equipment or reporting equipment failure.


TM 9-1005-338-13&P 0012 00


TM 9-1005-338-13&P 0013 00 PREVENTIVE MAINTENANCE CHECKS AND SERVICES - OPERATOR

WARNING Before starting an inspection, be sure to clear the weapon. Do not actuate the trigger until the weapon has been cleared. Inspect the chamber to be sure that it is empty. Check to see that there are no obstructions in the barrel.

GENERAL: Inspect all assemblies for missing, broken, or loose parts. Inspect parts for cracks, dents, burrs, excessive wear, rust, or corrosion. Make sure all parts are cleaned and lubricated. Do not use cleaning solvents or lubricants on any composite/rubber components. Inspect external surfaces for adequate finish. Refinish if necessary using solid film lubricant (item 4, WP 0047 00). Repair or replace authorized defective parts or notify direct support maintenance if repair or replacement is not authorized.

Table 1. Operator Preventive Maintenance Checks and Services Item

Interval

Man- Hours

Item to be Checked

Procedures

Not Fully Mission Capable if:

1 B/A Shotgun Check for missing pins, screws, and locking caps.

Pins, screws, and locking caps are missing.

B/A Check overall finish on metal surfaces.

1/3 of receiver finish is missing (shiny).

2 B Safety Cock shotgun. Move safety rearward to “SAFE” position and pull trigger.

Hammer releases and strikes firing pin.

3 B/A Action Lock Depress action lock. Fore end should slide back smoothly.

Fore end does not move.

4 B/A Trigger Move safety forward to “FIRE” position and pull trigger.

Hammer does not release.

5 B/A Barrel Check bore and chamber for obstructions and abnormalities. Check barrel for looseness. Inspect barrel for rust, cracks, dents, and bulges. Check barrel for straightness.

Obstruction in bore or barrel is damaged. Barrel is loose. Barrel is rusted, cracked, dented, or bulging. Barrel is noticeably bent.

6 B/A Fore End and Stock

Inspect parts for cracks and holes. Fore End or Stock is cracked or broken.


TM 9-1005-338-13&P 0013 00 PREVENTIVE MAINTENANCE CHECKS AND SERVICES - OPERATOR (cont)

Table 1. Operator Preventive Maintenance Checks and Services (cont) Item

Interval

Man- Hours

Item to be Checked

Procedures


7 B/A Recoil Pad Inspect for deterioration. Recoil pad is pitted, split, or missing.

8 B/A Front Sight Inspect for missing front bead. Front sight missing or loose.

9 B/A Sling and Swivels Sling or swivel(s) are present and function properly.

Sling or swivel(s) are missing; do not function properly.

END OF WORK PACKAGE


TM 9-1005-338-13&P 0014 00 OPERATOR MAINTENANCE – FIELD STRIPPING DISASSEMBLY

WARNING Before starting an inspection, be sure to clear the weapon. Do not actuate the trigger until the weapon has been cleared. Inspect the chamber to be sure that it is empty, and check to see that there are no obstructions in the barrel.

Move the safety (1) to “SAFE” (fully to the rear). Depress the action lock lever (2) and open the action by sliding the forearm fully rearward. Move the forearm (3) slowly forward from the rearward position until the front of the bolt is in the middle of the ejection port (4). Unlock barrel assembly (5) by turning the takedown screw assembly (6) counterclockwise until screw threads are completely disengaged from the end of the magazine tube (7) (Model 500 only). Unlock barrel assembly (5) by turning magazine cap (8) counterclockwise until screw threads are completely disengaged from the end of the magazine tube (7) (Model 590 only). Remove the barrel (5) from the receiver with a gentle back and forth rotational movement while pulling the barrel from the receiver assembly.

2MB0013

1

23

4

5

6

7

8M590

5


TM 9-1005-338-13&P 0014 00 OPERATOR MAINTENANCE – FIELD STRIPPING (cont) DISASSEMBLY (cont)

CAUTION Do not allow the hammer to fall when removing the trigger group from the receiver. To do so may result in personal injury or damage to equipment.

Position the shotgun on a clean surface with the trigger guard upward. Push out trigger housing retainer pin (9) from the receiver. Rotate the rear of the trigger mechanism (10) upward and remove the trigger mechanism (10) from the receiver.

10

9

2MB0014 Remove cartridge interrupter (11) from the ejection port side of the receiver. Remove the cartridge stop (12) from the opposite side of the receiver.

11 12

2MB0015

NOTE Note the position of the bolt (13); bolt slide (14) and action bar assembly (16), as these parts must be in the same relationship during assembly.

Move the forearm/action slide assembly rearward until the bolt assembly (13) and bolt slide (14) are three quarters of the way rearward. When the bottom of the bolt slide (14) is aligned with the clearance cuts in the side of the receiver, lift the bolt slide upward and out of the receiver.


TM 9-1005-338-13&P 0014 00 Remove fore end assembly (3) from magazine tube. Push bolt (13) out the front of the receiver assembly. Compress and remove elevator (15) from receiver.

314

13

152MB0016

16

Further disassembly of components is not authorized. ASSEMBLY Ensure the safety (1) is in “SAFE” (fully to the rear). Insert compressed elevator (15) into receiver. Depress ejector and insert bolt (13) into receiver. Push sides of elevator (15) down beside the bolt and slide the bolt (13) back. Install fore end assembly (3) over magazine tube (7). Insert action bars (16) into slots in the front of the receiver on either side of the magazine tube (6).

NOTE Moving the fore end assembly (3) approximately three quarters of the way forward will ease installation of the bolt slide (14).

Insert bolt slide (14), lower the front end and insert rear end first so lug fits in slot in bolt lock and is retained by the action bar.

2MB0017

1

7

314

13

15


TM 9-1005-338-13&P 0014 00 OPERATOR MAINTENANCE – FIELD STRIPPING (cont) ASSEMBLY (cont) Push down bolt slide (14) and move action slide (3) to rear until engaged. Move the bolt (13), bolt slide (14), and action (3) forward. Insert interrupter (11) and cartridge stop (12).

11 12

2MB0015

NOTE Hammer must be in the fully cocked position to allow the trigger housing to be inserted in the receiver.

Hold the cartridge stop (12) and cartridge interrupter (11) in place firmly against the receiver walls with one hand and grasp the trigger mechanism assembly (10) with the other. Insert the lugs (17) on each side of the front cover of the trigger mechanism (10) into the slots (18) on each side of the receiver. Ease the rear of the trigger mechanism (10) down and into position. DO NOT FORCE!


TM 9-1005-338-13&P 0014 00

NOTE If the trigger mechanism (10) does not fit into place easily, check that all internal pins in the trigger mechanism (10) are flush with the side of the housing and that the cartridge stop and cartridge interrupter are positioned correctly.

Align the trigger mechanism pin hole in the trigger mechanism with those in the receiver and insert the trigger housing retainer pin (9) until fully flush on both sides.

10

9

2MB0018

1817

WARNING Visually inspect the inside of the barrel to ensure it is free of obstructions, excessive oil or grease. Failure to do so may result in personal injury or damage to the weapon when the weapon is fired.

Depress the action lock lever (2) and move the forearm (3) rearward until the front of the bolt is in the middle of the ejection port (4).

NOTE Be sure the barrel is firmly seated to the receiver by looking through the ejection port. The barrel extension must rest firmly against the corresponding cut in the top of the receiver.

Slide the barrel (5) into the receiver and tighten the takedown screw (6) fully clockwise finger tight only (Model 500 only).

2MB0013

1

23

4

5

6

7

8M590

5


TM 9-1005-338-13&P 0014 00 OPERATOR MAINTENANCE – FIELD STRIPPING (cont) ASSEMBLY (cont) Slide the barrel (5) into the receiver and tighten the magazine cap (5) fully clockwise finger tight only (Model 590 only).

2MB0013

1

23

4

5

6

7

8M590

5

Perform safety/function check (WP 0017 00).

END OF WORK PACKAGE


TM 9-1005-338-13&P 0015 00 OPERATOR MAINTENANCE – CLEANING Cleaning should be performed:

• After each firing.

• After any exposure to extreme environmental conditions.

• Minimum of every 30 days. BOLT ASSEMBLY Use bore cleaning brush with bore cleaning solution. Clean all carbon and powder residue from the extractor and bolt face. Carefully clean under the hooks of the extractors. Wipe with clean, dry wiping rag (item 7, WP 0047 00). BARREL Use bore cleaning brush with bore cleaning solution. Wipe the barrel chamber and bore using a clean, dry patch. Using a cleaning rod with clean dry patch for each pass through the barrel. Continue process until the patch comes out clean. METAL SURFACES Using a fiber or nylon brush and cleaning solvent (item 3, WP 0047 00) clean all metal surfaces. Wipe with clean, dry wiping rag (item 7, WP 0047 00). RUBBER OR COMPOSITE SURFACES Clean with soap and water. Wipe dry with clean, dry wiping rag (item 7, WP 0047 00). LUBRICATION Lubricate all metal surfaces in accordance with WP 0016 00.

END OF WORK PACKAGE


TM 9-1005-338-13&P 0015 00


TM 9-1005-338-13&P 0016 00 OPERATOR MAINTENANCE – LUBRICATION Under all but the coldest artic conditions, LSA (item 6, WP 0047 00) or CLP (item 2, WP 0047 00) are the lubricants to use on your shotgun. Remember to remove excessive oil from the bore before firing.

NOTE Lubrication instructions are mandatory. Do not mix lubricants on the same weapon. The weapon must be thoroughly cleaned during change from one lubricant to another. Cleaning solvent (available to unit maintenance) is recommended for cleaning during change from one lubricant to another. Only lubricants and cleaners specified in this manual are authorized for use on this weapon.

+10OF(-12OC)

-10OF(-23OC)

2MB0019

CLP –Cleaner, lubricant and preservative (item 2, WP 0047 00). LSA – Weapons lubricating oil, semi-fluid (item 6, WP 0047 00). Between 10OF (-12OC) and –10OF (-23OC) use CLP, LSA or LAW. Below –10OF (-23OC) use only LAW. LAW – Weapons lubricating oil, artic (item 5, WP 0047 00). Lightly lube – A film of oil barely visible to the eye.

After firing, field strip your shotgun (WP 0014 00). Clean in accordance with WP 0015 00. Wipe dry and lube as required. Inspect and run a lightly oiled swab (item 9, WP 0047 00) through the bore and chamber. If your shotgun isn’t used, it still needs complete cleaning and lubing at least every 30 days. (Unusual conditions could shorten this interval.)

END OF WORK PACKAGE


TM 9-1005-338-13&P 0016 00


TM 9-1005-338-13&P 0017 00 FUNCTION CHECK A safety/function check should be performed anytime the shotgun is reassembled. This check will indicate whether the shotgun has been properly assembled. A properly executed safety/function check can also reveal many obvious malfunctions that can occur.

WARNING Before starting an inspection, be sure to clear the weapon. Do not actuate the trigger until the weapon has been cleared. Inspect the chamber to be sure that it is empty, and check to see that there are no obstructions in the barrel.

Clear the shotgun (WP 0004 00). Move the safety rearward to the “SAFE” position. Close the action fully. The action lock should be fully down. Pull the trigger; the hammer should NOT fall. Move the safety forward to the “FIRE” position. Pull the trigger; hammer should fall and the lock lever should be fully up. Hold trigger to the rear; recock the weapon by moving the forearm fully to the rear and then forward. Release the trigger; hammer should NOT fall and trigger should return to it forward position. Pull trigger; hammer should fall and the lock lever should be fully up Release trigger and recock the weapon by moving the forearm fully to the rear and then forward. The hammer should NOT fall. Move the safety rearward to the “SAFE” position.

NOTE Perform the following steps only if DUMMY rounds are available.

Load two DUMMY shot-shells into the magazine tube (WP 0004 00). Depress the action lever and open the action fully. Dummy shot-shell should feed onto the elevator. Release action lever and close action fully. Dummy shot-shell should feed into the chamber. Depress the action lever and open the action fully. The first dummy shot-shell should be extracted and ejected and the second dummy shot-shell should feed onto the elevator. Release action lock lever and close the action fully. Second dummy shot-shell should feed into the chamber. Depress the action lever and open the action fully. The second dummy shot-shell should be extracted and ejected.

END OF WORK PACKAGE


TM 9-1005-338-13&P 0017 00


CHAPTER 3

UNIT MAINTENANCE http://www.emilitarymanuals.com

TM 9-1005-338-13&P 0018 00 SERVICE UPON RECEIPT OF MATERIEL

Table 1. Service Upon Receipt


LOCATION ITEM ACTION REMARKS

1. Container Basic Issue Items Check unpacked equipment. • Inspect the equipment for damage

incurred during shipment. If the equipment has been damaged, report the damage on SF 364, Report of Discrepancy (ROD).

• Check the equipment against the packing slip to see if the shipment is complete. Report all discrepancies in accordance with instructions of DA PAM 738-750.

• Check to see whether the equipment has been modified.

2. Shotgun Barrel Assembly • Remove volatile corrosion inhibitor (VCI) from barrels. Discard.

Shotgun • Field strip weapon and inspect for missing parts.

• Clean and lubricate. • Reassemble. • Perform function check (WP 0017

00).

END OF WORK PACKAGE


TM 9-1005-338-13&P 0018 00


TM 9-1005-338-13&P 0019 00 UNIT MAINTENANCE INSTRUCTIONS This work package contains information regarding repair parts, special tools, and support equipment and instructions for service upon receipt, PMCS, and unit maintenance to keep the machine gun in good repair. COMMON TOOLS AND EQUIPMENT For authorized common tools and equipment, refer to the Modified Table of Organization and Equipment (MTOE) (WP 0042 00) applicable to your unit. SPECIAL TOOLS, TMDE, AND SUPPORT EQUIPMENT There are no special tools for this item. Tools and test equipment are listed in WP 0034 00 of this manual. There is no Test, Measurement, and Diagnostic Equipment (TMDE) for this item. REPAIR PARTS Repair parts are listed and illustrated in the repair parts and special tools list (RPSTL) (WP 0036 00 through WP 0042 00) covering unit and direct support maintenance for this equipment.


TM 9-1005-338-13&P 0019 00


TM 9-1005-338-13&P 0020 00 UNIT MAINTENANCE TROUBLESHOOTING PROCEDURES This work package contains unit-troubleshooting information for locating and correcting most of the operating troubles that may develop in the shotgun. Each malfunction for a part, assembly, or subassembly is followed by a list of tests or inspections, which will help you to determine corrective actions to take. You should perform the tests/inspections and corrective actions in the order listed. This manual cannot list all possible malfunctions that may occur, nor all tests or inspections and corrective actions. If a malfunction is not listed (except when malfunction or cause is obvious) or is not corrected by listed corrective actions, notify direct support maintenance. TROUBLESHOOTING PROCEDURES Refer to symptom index or troubleshooting table for malfunctions, tests/inspections, and corrective action.

SYMPTOM INDEX Troubleshooting Procedure Work Package/Page Ammunition double feeds ..................................................................................................... 0020 00-3 Cartridge fails to extract or eject ........................................................................................... 0020 00-3 Shotgun fails to load or feed ................................................................................................. 0020 00-2 Shotgun will not fire............................................................................................................... 0020 00-2


TM 9-1005-338-13&P 0020 00 UNIT MAINTENANCE TROUBLESHOOTING PROCEDURES (cont)

Table 1. Unit Troubleshooting Procedures SYMPTOM Shotgun will not fire.

MALFUNCTION Firing pin well in bolt assembly is obstructed or dirty.

CORRECTIVE ACTION Notify direct support maintenance.

MALFUNCTION Firing pin is burred, excessively worn or broken.


MALFUNCTION Bolt assembly will not slide forward by pushing fore end forward.

CORRECTIVE ACTION Clean, lube and reassemble properly. If fore end will not slide forward, notify direct support maintenance.

SYMPTOM Shotgun fails to load or feed.

MALFUNCTION Action slide does not function properly.

CORRECTIVE ACTION If action slide is defective, notify direct support maintenance.

MALFUNCTION Magazine spring weak or broken



TM 9-1005-338-13&P 0020 00 SYMPTOM Ammunition double feeds.



SYMPTOM Cartridge fails to extract or eject.

MALFUNCTION Cartridge extractors and/or ejector burred, bent, broken or missing.


END OF WORK PACKAGE


TM 9-1005-338-13&P 0020 00


TM 9-1005-338 13&P 0021 00 UNIT MAINTENANCE – PREVENTIVE MAINTENANCE CHECKS AND SERVICES


Table 1. Preventive Maintenance Checks and Services

NOTE

Unless otherwise stated, inspections are quarterly. Item

Interval

Man- Hours

Item to be Checked

Procedures


1 Q Shotgun Check for missing pins, screws, and locking caps. Check metal surface finish; touch up if necessary. Check sling for tears or worn webbing. Check for broken or missing swivels. Function check.

Pins, screws, or locking caps are missing. Missing one third or more of its exterior protective finish.

NOTE

Solid Film Lubricant (SFL) is the authorized touchup for the shotgun and may be used on up to one third of the exterior receiver finish of the weapon. FOR CONUS USE ONLY: Solid Film Lubricant (item 4, WP 0047 00) may be used as a touchup without limitation on the receiver assembly. This is to say that the units which DO NOT fall under the category of Divisional Combat Units of rapid deployment type units may have up to 100% of the exterior surface of the receiver assembly protected with SFL. Prior to application of SFL, the surface must be thoroughly cleaned and inspected for corrosion and/or damage. If corroded or damaged, the part must be repaired or replace prior to application of SFL. Continued use under combat conditions would result in an unprotected surface when the SFL wears off. This would result in a large light reflecting surface and accelerated deterioration of the unprotected surface. Therefore, Divisional Combat Units, and units that fall under the definition of Rapid Deployment type must adhere to the limitation of NOT over one third of their exterior surface covered by SFL. If the shotgun is missing one third or more of its exterior receiver protective finish, resulting in an unprotected/light-reflecting surface, this missing finish will be considered a shortcoming. This shortcoming requires action to obtain a replacement weapon. Once a replacement has been received, evacuate the original weapon to depot for overhaul.


TM 9-1005-338 13&P 0021 00 UNIT MAINTENANCE – PREVENTIVE MAINTENANCE CHECKS AND SERVICES (cont)

Table 1. Unit Preventive Maintenance Checks and Services (cont) Item

Interval

Man- Hours

Item to be Checked

Procedures


5 Q Trigger Guard Pin

Check pin(s) for burrs, bends, and looseness of installation.

Pin(s) are loose or missing.

6 Q Trigger Assembly Check trigger assembly for proper operation.

Trigger hangs loose, will not move, or is bent or broken.

7 Q Carrier Check carrier for proper operation. Carrier hangs loose, will not move, or is bent or broken.

8 Q Magazine Cap Check magazine cap for proper installation, burrs, and stripped threads.

Threads are stripped; cap is burred, or improperly installed.

9 Q Barrel Check barrel for looseness. Inspect barrel for rust, cracks, dents, and bulges. Check barrel for straightness.

Barrel is loose. Barrel is rusted, cracked, dented, or bulging. Barrel is noticeably bent.

10 Q Butt Stock Inspect for cracks and breakage; looseness.

Butt plate is loose, cracked or broken; ; creates hazard to shooter.

11 Q Front Sight Inspect for looseness or missing front sight.

Sight is loose or missing.

12 Q Fore End Assembly

Check action slide assembly arms for excessive wear, burrs, and straightness. Inspect for cracks.

Action slide assembly arm s are bent, worn or broken. Structural strength is impaired; create hazard to shooter.


TM 9-1005-338 13&P 0021 00 14 Q Bolt Assembly Check bolt for freedom of movement.

Check bolt lock pinhole for burrs, excessive wear, or warping. Check for broken or missing bolt lock.

Bolt will not move. Bolt lock pinhole is burred, worn, or warped. Pin is broken or missing.

15 Q Ejector Check for burrs, excessive wear and straightness.

Ejector s burred, excessively worn, or bent.

16 Q Receiver Check that magazine tube is secured to the receiver. Check tube for dents, burrs, and damage that will restrict the passage of ammunition through the magazine tube. Check for rust and corrosion.

Magazine tube is loose. Magazine tube is dented, burred, or damaged and will not allow the passage of ammunition. Tube is rusted or corroded.

END OF WORK PACKAGE


TM 9-1005-338 13&P 0021 00


TM 9-1005-338-13&P 0022 00 UNIT MAINTENANCE OF MOSSBERG 12-GAUGE SHOTGUN, MODEL 500, NSN 1005-01-295-1862, P/N MOD500; MOSSBERG 12-GAUGE SHOTGUN, MODEL 590, NSN 1005-01-251-8578, P/N 52660 This task covers: a. Disassembly b. Inspection/Repair c. Assembly INITIAL SETUP Tools and Special Tools:

Tool Kit, Small Arms Repairman, P/N SC 5180-95-B71

Equipment Condition: Shotgun field stripped (WP 0014 00)

DISASSEMBLY If damaged, remove magazine cap (1) from barrel assembly (2) (M590 only).

2MB0020

M500

M590

2

1

INSPECTION/REPAIR Check for broken, missing, or damaged parts. For repair of Fore End Assembly refer to WP 0023 00. For repair of Barrel Assembly refer to WP 0024 00. For repair of Stock Assembly refer to WP 0025 00. Check for damage to internal threads in magazine cap (1) (M590 only). Repair is by replacement of authorized parts.


TM 9-1005-338-13&P 0022 00 UNIT MAINTENANCE OF MOSSBERG 12-GAUGE SHOTGUN, MODEL 500, NSN 1005-01-295-1862, P/N MOD500; MOSSBERG 12-GAUGE SHOTGUN, MODEL 590, NSN 1005-01-251-8578, P/N 52660 ASSEMBLY If removed, attach magazine cap (1) to barrel assembly (2) (M590 only).

2MB0020

M500

M590

2

1

END OF WORK PACKAGE


TM 9-1005-338-13&P 0023 00 UNIT MAINTENANCE OF FORE END ASSEMBLY, NSNA, P/N MOSS-05 This task covers: a. Disassembly b. Inspection/Repair c. Assembly INITIAL SETUP Tools and Special Tools:

Tool Kit, Small Arms Repairman, P/N SC 5180-95-B71 Tube Nut Tube (Fig. 1, WP 0030 00)

Equipment Condition: Barrel removed for receiver (WP 0014 00).

DISASSEMBLY Using tube nut tool, remove slide tube nut (1) from action slide assembly (2).

WARNING To avoid injury your eyes, use care when removing and installing spring-loaded parts.

Remove shotgun slide grip (3) and anti-rattle spring (4) from action slide assembly (2).

1

2MB0021

TOOL

2

3

45

INSPECTION/REPAIR Check slide tube nut (1) for burred/worn threads. Check slide grip (3) for cracks or breaks. Check action slide assembly (2) for bent tube, burred/worn threads; cracked/bent action slide arms (5). Check anti-rattle spring (4) for deformities that would prevent proper retention. Repair is by replacement of authorized parts. ASSEMBLY


Slide shotgun slide grip (3) onto action slide assembly (2) and install anti-rattle spring (4). Screw slide tube nut (1) onto action slide assembly (2) and tighten using tube nut tool.

END OF WORK PACKAGE


TM 9-1005-338-13&P 0023 00


TM 9-1005-338-13&P 0024 00 UNIT MAINTENANCE OF BARREL ASSEMBLY, NSN 1005-01-512-9286, P/N 3907P AND BARREL ASSEMBLY, NSNA, P/N 41758 This task covers: a. Disassembly b. Inspection/Repair c. Assembly INITIAL SETUP Tools and Special Tools:


Materials/Parts: Nut, Self-locking (2), P/N Equipment Condition:

Shotgun field stripped (WP 0014 00). DISASSEMBLY Remove two self-locking nuts (1), two screws (2), heat shield spacer (3), and heat shield (4) from barrel (5). Discard self-locking nuts (1) (M590 only). Remove front sight (6) from barrel (5) (both models).

4

3

2

1

6

5

2MB0022 Remove retaining ring (7) and machine screw (8) from barrel (5) (M500 only).

7

2MB0023

8

5


TM 9-1005-338-13&P 0024 00 UNIT MAINTENANCE OF BARREL ASSEMBLY, NSN 1005-01-512-9286, P/N 3907P AND BARREL ASSEMBLY, NSNA, P/N 41758 (cont) DISASSEMBLY (cont)

NOTE Remove swivel only if damaged.

Removal of old /new swivel is the same for both models.

OLD STYLE SWIVEL Remove screw (9), swivel (10), and sleeve bushing (11).

10

11

9

M5002MB0024

M590

9 1011

NEW STYLE SWIVEL Turn locking knob (12) completely counterclockwise. Push in on knob (12) to release swivel-locking bar (13) and remove sling swivel (14) from swivel post (15). Turn swivel post (15) counterclockwise to remove.

2MB0024AM590M500

1213

12

13

14

15

14

15


TM 9-1005-338-13&P 0024 00 INSPECTION/REPAIR Visually check barrel for straightness. If bent, notify direct support maintenance. Check heat shield for bends/cracks; missing screws or nuts. Check for missing/bent swivel. If old style swivel is damaged, replace with new style swivel. Check for damaged sleeve bushing; burred/worn threads of machine screw (M500 only). Repair is by replacement of authorized parts. ASSEMBLY

NOTE If old style swivel was removed, replace with new style swivel.

Install swivel post (15) by turning clockwise. Turn locking knob (12) completely counterclockwise. Push in on knob (12) to release swivel-locking bar (13) and insert through swivel post (15). Tighten locking knob (12) by turning completely clockwise.

2MB0024AM590M500

1213

12

13

14

15

14

15


TM 9-1005-338-13&P 0024 00 UNIT MAINTENANCE OF BARREL ASSEMBLY, NSN 1005-01-512-9286, P/N 3907P AND BARREL ASSEMBLY, NSNA, P/N 41758 (cont) ASSEMBLY Install front sight (6) from barrel (5) (both models). Install heat shield (4), heat shield spacer (3), two screws (2) and two new self-locking nuts (1) to barrel (5) (M590 only).

4

3

2

1

6

5

2MB0022 Install retaining ring (7) and machine screw (8) on barrel (5) (M500 only).

7

2MB0023A

8

5

END OF WORK PACKAGE


TM 9-1005-338-13&P 0025 00 UNIT MAINTENANCE OF STOCK, GUN, SHOULDER, NSN 1005-01-511-9538, P/N 14762MIL This task covers: a. Disassembly b. Inspection/Repair c. Assembly INITIAL SETUP Tools and Special Tools:


Materials/Parts: Lock-washer, P/N 7615P

DISASSEMBLY Remove two machine screws (1) and recoil pad (2) from stock (3). Remove machine screw (4), washer (5), and lock-washer (6) from stock (3) and separate the stock from the receiver. Discard lock-washer (6).

1

2

3

4

5 6

2MB0025


TM 9-1005-338-13&P 0025 00 UNIT MAINTENANCE OF STOCK, GUN, SHOULDER, NSN 1005-01-511-9538, P/N 14762MIL (cont) DISASSEMBLY (cont) OLD STYLE SWIVEL

NOTE Remove swivel only if damaged.

Removal of old /new swivel is the same for both models.

Remove screw (7), and swivel (8). Remove sleeve bushing (9) and swivel washer (10) (M500 only).

3

7

87

8

910

M500

2MB0025A NEW STYLE SWIVEL Turn locking knob (11) completely counterclockwise. Push in on knob (11) to release swivel-locking bar (12) and remove sling swivel (13) from swivel post (14). Turn swivel post (14) counterclockwise to remove.

3

2MB0025B

111213

14


TM 9-1005-338-13&P 0025 00 INSPECTION/REPAIR Check stock for cracks. Check for missing/damaged sleeve bushing; burred/worn threads on machine screws. Check for missing/bent swivel. If old style swivel is damaged, replace with new style swivel. Check recoil pad for deterioration. Repair is by replacement of authorized parts. ASSEMBLY

NOTE If old style swivel was removed, replace with new style swivel.

Install swivel post (15) by turning clockwise. Turn locking knob (12) completely counterclockwise. Push in on knob (12) to release swivel-locking bar (13) and insert through swivel post (15). Tighten locking knob (12) by turning completely clockwise.

3

2MB0025B

111213

14


TM 9-1005-338-13&P 0025 00 UNIT MAINTENANCE OF STOCK, GUN, SHOULDER, NSN 1005-01-511-9538, P/N 14762MIL (cont) ASSEMBLY (cont) Align the stock with the receiver assembly. Place washer (5) and lock-washer (6) on shaft of machine screw (4); insert machine screw (4) into end of stock (3) and tighten screw into receiver. Align recoil pad (2) with end of stock (3) and secure with two machine screws (1).

1

2

3

4

5 6

2MB0025

END OF WORK PACKAGE


TM 9-1005-338-13&P 0026 00 UNIT MAINTENANCE OF GRIP ASSEMBLY, PISTOL, NSN 1005-01-512-2743, P/N 7995P This task covers: a. Disassembly b. Inspection/Repair c. Assembly INITIAL SETUP Tools and Special Tools:


Materials/Parts: Lock-washer, P/N 7613P

Equipment Condition:

Shotgun field stripped (WP 0014 00).

NOTE To replace shoulder gun stock with the pistol grip assembly remove shoulder gun stock in accordance with WP 0025 00. Follow assembly procedures in this work package to install the pistol grip assembly

DISASSEMBLY Remove hex screw (1), washer (2), and lock-washer (3) from pistol grip (4). Discard lock-washer (3). Remove swivel post (5).

2MB0056

1

3

2

4

5

INSPECTION AND REPAIR Check pistol grip for cracks. Check screw and swivel for burred/worn threads. Check for missing, worn and broken parts. Repair is by replacement of authorized parts.


TM 9-1005-338-13&P 0026 00 UNIT MAINTENANCE OF GRIP ASSEMBLY, PISTOL, NSN 1005-01-512-2743, P/N 7995P (cont) ASSEMBLY Align pistol grip to receiver. Place new lock-washer (3) and washer (2) on hex screw (1) and insert into pistol grip (4). Tighten screw hand tight only. Install swivel post (5).

2MB0056

1

3

2

4

5

END OF WORK PACKAGE


CHAPTER 4

DIRECT SUPPORT MAINTENANCE http://www.emilitarymanuals.com

TM 9-1005-338-13&P 0027 00 DIRECT SUPPORT TROUBLESHOOTING PROCEDURES This work package contains direct support-troubleshooting information for locating and correcting most of the operating troubles that may develop in the shotgun. Each malfunction for a part, assembly, or subassembly is followed by a list of tests or inspections, which will help you to determine corrective actions to take. You should perform the tests/inspections and corrective actions in the order listed. This manual cannot list all possible malfunctions that may occur, nor all tests or inspections and corrective actions. If a malfunction is not listed (except when malfunction or cause is obvious) or is not corrected by listed corrective actions, notify direct support maintenance. TROUBLESHOOTING PROCEDURES Refer to symptom index or troubleshooting table for malfunctions, tests/inspections, and corrective action.

SYMPTOM INDEX Troubleshooting Procedure Work Package/Page Ammunition double feeds ..................................................................................................... 0027 00-4 Cartridge fails to extract or eject ........................................................................................... 0027 00-3 Shotgun does not function correctly. .................................................................................... 0027 00-4 Shotgun fails to load or feed ................................................................................................. 0027 00-3 Shotgun will not fire............................................................................................................... 0027 00-2


TM 9-1005-338-13&P 0027 00 DIRECT SUPPORT TROUBLESHOOTING PROCEDURES (cont)

Table 1. Direct Support Troubleshooting Procedures SYMPTOM Shotgun will not fire.

MALFUNCTION Firing pin is burred, excessively worn or broken.

CORRECTIVE ACTION Replace firing pin.

MALFUNCTION Check for foreign matter in firing pin aperture in bolt.

CORRECTIVE ACTION Clean aperture in bolt and bolt slide.

MALFUNCTION Check for broken trigger assembly.

CORRECTIVE ACTION Replace trigger assembly.

MALFUNCTION Check for foreign matter in safety well.

CORRECTIVE ACTION Clean safety well.


TM 9-1005-338-13&P 0027 00 SYMPTOM Cartridge fails to extract or eject.

MALFUNCTION Cartridge extractors and/or ejector are worn, burred, broken or missing.

CORRECTIVE ACTION Replace cartridge extractors and/or ejector.

MALFUNCTION Check for bent or broken extractor spring(s) on cartridge extractor.

CORRECTIVE ACTION If one is damaged, replace both extractor spring(s).

SYMPTOM Shotgun fails to load or feed.

MALFUNCTION Cartridge follower is corroded.

CORRECTIVE ACTION Clean or replace cartridge follower.

MALFUNCTION Magazine spring is broken or kinked.

CORRECTIVE ACTION Replace magazine spring.

MALFUNCTION Foreign matter is in magazine tube.

CORRECTIVE ACTION Clean magazine tube.

MALFUNCTION Cartridge stop and/or cartridge interrupter is worn, burred, or broken.

CORRECTIVE ACTION Replace cartridge stop and/or cartridge interrupter.


TM 9-1005-338-13&P 0027 00 DIRECT SUPPORT TROUBLESHOOTING PROCEDURES (cont)

Table 1. Direct Support Troubleshooting Procedures (cont) SYMPTOM Ammunition double feeds.


CORRECTIVE ACTION Replace action slide assembly.

SYMPTOM Shotgun does not function correctly.

MALFUNCTION Safety is burred or sticking.

CORRECTIVE ACTION Replace, or clean and lubricate safety.

END OF WORK PACKAGE


TM 9-1005-338-13&P 0028 00 DIRECT SUPPORT MAINTENANCE OF RECEIVER ASSEMBLY, NSNA, P/N 10171MIL AND RECEIVER ASSEMBLY, NSNA, P/N 10171A1 This task covers: a. Disassembly b. Inspection/Repair c. Assembly INITIAL SETUP Tools and Special Tools:

Tool Kit, Small Arms Repairman, P/N SC 5180-95-B71 Shop Set, Small Arms: Field Maintenance, Basic Less Power, P/N SC4933-95-CL-A11

Materials/Parts: Lock-washer, P/N 11756 Wiping Rag, (item 7, WP 0045 00)

Equipment Condition:

Barrel assembly and fore end assembly removed (WP 0014 00).

DISASSEMBLY MODEL M500 Wrap wiping rag around receiver assembly (1). Place receiver assembly (1) in bench vise with vise jaw caps. Close vise just enough to hold receiver assembly (1). Place strap style pipe wrench around magazine tube assembly (2) and turn to the left (counterclockwise), loosening metal tube assembly (2). Remove magazine tube assembly (2) from receiver assembly (1).

2

1

2MB0027


Remove cartridge follower (3) and magazine spring (4) from magazine tube assembly (2).

43

2MB0028

2

1


TM 9-1005-338-13&P 0028 00 DIRECT SUPPORT MAINTENANCE OF RECEIVER ASSEMBLY, NSNA, P/N 10171MIL AND RECEIVER ASSEMBLY, NSNA, P/N 10171A1 (cont) DISASSEMBLY MODEL M590


Remove magazine catch retainer (5), magazine spring (4) and cartridge follower (3) from magazine tube assembly (2).

2MB0029

43

2

5

1

NOTE Perform this step only if replacement of magazine tube is required.

Wrap wiping rag around receiver assembly (1). Place receiver assembly (1) in bench vise with vise jaw caps. Close vise just enough to hold receiver assembly (1). Place strap style pipe wrench around magazine tube assembly (2) and turn to the left (counterclockwise), loosening metal tube assembly (2). Remove magazine tube assembly (2) from receiver assembly (1).

2

1

2MB0027


TM 9-1005-338-13&P 0028 00 INSPECTION/REPAIR Inspect for broken, damaged, or missing parts. Inspect receiver (1) for cracks or bends, repair is by replacement of shotgun. Inspect magazine tube (2) for cracks or bends. Inspect magazine spring (3) for bends/breaks and flat spots. Repair is by replacement of authorized parts. ASSEMBLY MODEL M500


Insert magazine spring (3) and cartridge follower (4) into magazine tube assembly (2).

43

2MB0028

2

1

Wrap wiping rag around receiver assembly (1). Place receiver assembly (1) in bench vise with vise jaw caps. Close vise just enough to hold receiver assembly (1). Place strap style pipe wrench around magazine tube assembly (2) and turn to the right (clockwise), tightening magazine tube assembly (2).

2

1

2MB0027 Assemble weapon (WP 0014 00).


TM 9-1005-338-13&P 0028 00 DIRECT SUPPORT MAINTENANCE OF RECEIVER ASSEMBLY, NSNA, P/N 10171MIL AND RECEIVER ASSEMBLY, NSNA, P/N 10171A1 (cont) ASSEMBLY (cont) MODEL M590

NOTE Perform this step only if magazine tube was replaced.

Wrap wiping rag around receiver assembly (1). Place receiver assembly (1) in bench vise with vise jaw caps. Close vise just enough to hold receiver assembly (1). Place strap style pipe wrench around new magazine tube assembly (2) and turn to the right (clockwise), tightening magazine tube assembly (2).

2

1

2MB0027


Insert cartridge follower (3), magazine spring (4) and magazine catch retainer (5) into magazine tube assembly (2).

2MB0029

43

2

5

1

Assemble weapon (WP 0014 00).


TM 9-1005-338-13&P 0028 00 FUNCTION CHECK After performing any work on your shotgun, such as cleaning or repair, check shotgun for proper functioning before firing any live ammunition.

END OF WORK PACKAGE


TM 9-1005-338-13&P 0028 00


TM 9-1005-338-13&P 0029 00 DIRECT SUPPORT MAINTENANCE OF BOLT ASSEMBLY, NSN 1005-01-512-2731, P/N 6706P This task covers: a. Disassembly b. Inspection/Repair c. Assembly INITIAL SETUP Tools and Special Tools:

Tool Kit, Small Arms Repairman, P/N SC 5180-95-B71 Shop Set, Small Arms: Field Maintenance, Basic Less Power, P/N SC4933-95-CL-A11

Equipment Condition: Shotgun field stripped (WP 0014 00)

DISASSEMBLY Remove grooved headless pin (1) and bolt lock (2) from bolt (3).

WARNING To avoid injury to your eyes, use care when removing and installing spring-loaded parts.

Remove two cartridge extractor pins (4 and 5), left hand cartridge extractor (6), right hand cartridge extractor (7), and two cartridge extractor springs (8) from bolt (3). Remove firing pin retaining pin (9), firing pin (10), flat washer (11), and follower spring (12) from bolt (3).

2

4

3

56

7

8

89

1011

12

2MB0030

1


TM 9-1005-338-13&P 0029 00 DIRECT SUPPORT MAINTENANCE OF BOLT ASSEMBLY, NSN 1005-01-512-2731, P/N 6706P (cont) INSPECTION/REPAIR Inspect bolt (3) and bolt lock (2) for cracks. Inspect all components for bends, breaks, or excessive wear. Repair is by replacement of authorized parts. ASSEMBLY Install follower spring (12), flat washer (11), firing pin (10), and firing pin retaining pin (9) into bolt (3).

WARNING To avoid injury to your eyes, use care when removing and installing springs loaded parts.

Install two cartridge extractor springs (8), right hand and left hand cartridge extractors (6 and 7), and cartridge extractor pins (4 and 5) into bolt (3). Install bolt lock (32) and grooved headless pin (1) into bolt (3).

2

4

3

56

7

8

89

1011

12

2MB0030

1

END OF WORK PACKAGE


TM 9-1005-338-13&P 0030 00 ILLUSTRATED LIST OF MANUFACTURED ITEMS SCOPE This work package includes complete instructions or making items authorized to be manufactured. HOW TO USE THE INDEX OF MANUFACTURED ITEMS A part number index in alphanumeric order is provided for cross-referencing the part number of the item to be manufactured to the page that covers fabrication criteria. EXPLANATION OF THE ILLUSTRATIONS OF MANUFACTURED ITEMS All instructions needed by maintenance personnel to manufacture the item are included on the illustrations. All bulk materials, needed for the manufacture of an item, are listed by part number or specification number in a tabular list on the illustration.

INDEX

Figure Number

Part Number/ Drawing Number

Nomenclature

1 Not Applicable Tube Nut Tool


TM 9-1005-338-13&P 0030 00 ILLUSTRATED LIST OF MANUFACTURED ITEMS (cont)

1/4"

1-1/2"

1/8"2"

3/4"

1/2"

2MB0031

Figure 1. Tube Nut Tool NOTES: Material: Bar, Metal, Type Grade 1080, QQ-S-634. Use NSN 9510-00-294-0992 (81348).

END OF WORK PACKAGE


TM 9-1005-338-13&P 0031 00 AMMUNITION CARE AND USAGE CARE - Protect ammunition from mud, dirt, and water. If ammunition gets wet or dirty, wipe it off prior to use. Wife off light corrosion as soon as it is discovered. Heavily corroded cartridge or cartridges that have dented cases should not be fired. HANDLING - Do not expose ammunition to the direct rays of the sun. If the power is hot, excessive pressure may develop when gun is fired. PRESERVATION - Do not open ammunition containers until the ammunition is to be used. Ammunition removed from airtight containers, particularly in damp climates, is likely to corrode. PACKING - Do not oil or grease ammunition. Dust and other abrasives collecting on oiled or greased ammunition will damage the operating parts of the shotgun. Oiled cartridges will produce excessive chamber pressure. Pack unused cartridges in original containers and use first in subsequent firings. AUTHORIZED AMMUNITION For ammunition authorized for use in your shotgun refer to WP 0009 00.

END OF WORK PACKAGE


TM 9-1005-338-13&P 0031 00


CHAPTER 5

SUPPORTING INFORMATION http://www.emilitarymanuals.com

TM 9-1005-338-13&P 0032 00 REFERENCES DEPARTMENT OF ARMY PAMPHLETS AND FORMS DA PAM 738-750 ................ Functional Users Manual for the Army Maintenance Management System

(TAMMS) DA Form 2028..................... Recommended Changes to Publications and Blank Forms PAM 385-64 ........................ Ammunition and Explosives Standards SF 364................................. Report of Discrepancy (ROD) SF 368................................. Product Quality Deficiency Report FIELD MANUALS FM 3-4................................. Nuclear, Biological, and Chemical (NBC) Protection FM 3-5................................. Nuclear, Biological, and Chemical (NBC) Decontamination FM 3-87............................... Nuclear, Biological, and Chemical (NBC) Reconnaissance and

Decontamination Operation (How to Fight) FM 4-25.11.......................... First Aid for Soldiers TECHNICAL MANUALS TM 750-244-7 ..................... Procedures for Destruction of Equipment in Federal Supply Classification 1000, 1005, 1010,1015, 1020, 1025, 1030, 1055, 1090, and 1095 to Prevent Enemy Use RELATED PUBLICATIONS DOD 4160.21-M-1............... Defense Demilitarization Manual MISCELLANEOUS PUBLICATIONS CTA 50-970......................... Expendable/Durable Items (Except Medical Class V, Repair Parts and Heraldic Items) CTA 8-100........................... Army Medical Department Expendable/Durable items


TM 9-1005-338-13&P 0032 00


TM 9-1005-338-13&P 0033 00 MAINTENANCE ALLOCATION CHART (MAC) INTRODUCTION The Army Maintenance System MAC This introduction provides a general explanation of all maintenance and repair functions authorized at various maintenance levels under the standard Army Maintenance System concept. The MAC (immediately following the introduction) designates overall authority and responsibility for the performance of maintenance functions on the identified end item or component. The application of the maintenance functions to the end item or component shall be consistent with the capacities and capabilities of the designated maintenance levels, which are shown on the MAC in column (4) as:

Unit – includes two sub-columns, C (crew/operator) and O (unit) maintenance. Direct Support – includes an F sub-column. General Support – includes an H sub-column. Depot – includes a D sub-column.

The tools and test equipment requirements (immediately following the MAC) list the tools and test equipment (both special tools and common tool sets) required for each maintenance function as referenced from the MAC. The remarks (immediately following the tools and test equipment requirements) contain supplemental instructions and explanatory notes for a particular maintenance function. Maintenance Functions Maintenance functions are limited to and defined as follows: Inspect. To determine the serviceability of an item by comparing its physical, mechanical, and/or electrical characteristics with established standards through examination (e.g., by sight, sound, or feel). This includes scheduled inspection and gagings and evaluation of cannon tubes. Test. To verify serviceability by measuring the mechanical, pneumatic, hydraulic, or electrical characteristics of an item and comparing those characteristics with prescribed standards on a scheduled basis, i.e., load testing of lift devices and hydrostatic testing of pressure hoses. Service. Operations required periodically to keep an item in proper operating condition; e.g., to clean (includes decontaminate, when required), to preserve, to drain, to paint, or to replenish fuel, lubricants, chemical fluids, or gases. This includes scheduled exercising and purging or recoil mechanisms. Adjust. To maintain or regulate, within prescribed limits, by bringing into proper position, or by setting the operating characteristics to specified parameters. Align. To adjust specified variable elements of an item to bring about optimum or desired performance. Calibrate. To determine and cause corrections to be made or to be adjusted on instruments of test, measuring, and diagnostic equipment used in precision measurement. Consists of comparisons of two instruments, one of which is certified standard of known accuracy, to detect and adjust any discrepancy in the accuracy of the instrument being compared.


TM 9-1005-338-13&P 0033 00 MAINTENANCE ALLOCATION CHART (MAC) (cont) Maintenance Functions (cont) Remove/Install. To remove and install the same item when required to perform service or other maintenance functions. Install may be the act of emplacing, seating, or fixing into position a spare, repair part, or module (component or assembly) in a manner to allow the proper functioning of an equipment or system. Replace. To remove an unserviceable item and install a serviceable counterpart in its place. “Replace” is authorized by the MAC and assigned maintenance level is shown as the third position code of the Source, Maintenance and Recoverability (SMR) code. Repair. The application of maintenance services, including fault location/troubleshooting, removal/installation, disassembly/assembly procedures, and maintenance actions to identify troubles and restore serviceability to an item by correction specific damage, fault, malfunction, or failure in a part, subassembly, module (component or assembly), end item, or system.

NOTE The following are applicable to the “repair” maintenance function: Services – Inspect, test, service, adjust, calibrate, and/or replace. Fault location/troubleshooting – The process of investigating and detecting the cause of equipment malfunctioning; the act of isolating a fault within a system or Unit Under Test (UUT). Disassembly/assembly – The step-by-step breakdown (taking apart) of a spare/functional group coded item to the level of its component, that is assigned an SMR code for the level of maintenance under consideration (i.e., identified as maintenance significant). Actions – Welding, grinding, riveting, straightening, facing, machining, and/or resurfacing.

Overhaul. That maintenance effort (service/action) prescribed to restore an item to a completely serviceable/operational condition as required by maintenance standards in appropriate technical publications. Overhaul is normally the highest degree of maintenance performed by the Army. Overhaul does not normally return an item to like new condition. Rebuild. Consists of those services/actions necessary for the restoration of unserviceable equipment to a like new condition in accordance with original manufacturing standards. Rebuild is the highest degree of materiel maintenance applied to Army equipment. The rebuild operation includes the act of returning to zero those age measurements (e.g., hours/miles) considered in classifying Army equipment/components. Explanation of Columns in the MAC Column (1) – Group Number. Column (1) lists FGC numbers, the purpose of which is to identify maintenance significant components, assemblies, subassemblies, and modules with the Next Higher Assembly (NHA)). Column (2) – Component/Assembly. Column (2) contains the item names of components, assemblies, subassemblies, and modules for which maintenance is authorized. Column (3) – Maintenance Function. Column (3) lists thee functions to be performed on the item listed in column (2). (For a detailed explanation of these functions refer to “Maintenance Functions” outlined above.


TM 9-1005-338-13&P 0033 00 Column (4) – Maintenance Level. Column (4) specifies each level of maintenance authorized to perform each function listed in column (3), by indicating work time required (expressed as man-hours in whole hours or decimals) in the appropriate sub-column. This work time figure represents the active time required to perform that maintenance function at the indicated level of maintenance. If the number or complexity of the tasks within the listed maintenance function varies at different maintenance levels, appropriate work time figures are to be shown for each level. The work time figure represents the average time required to restore an item (assembly, sub-assembly, component, module, end item, or system) to a serviceable condition under typical field operating conditions. This time includes preparation time, and quality assurance time in addition to the time required to perform the specific tasks identified for the maintenance functions authorized in the MAC. The symbol designations for the various maintenance levels are as follows:

C – Operator or Crew maintenance O – Unit Maintenance F – Direct Support Maintenance L – Specialized Repair Activity (SRA) H – General Support Maintenance D – Depot Maintenance

NOTE

The “L” maintenance level is not included in column (4) of the MAC. Functions to this level of maintenance are identified by work time figures in the “H” column of column (4), and an associated reference code is used in the REMARKS column (6). This code is keyed to the remarks and the SRA complete repair application is explained there.

Column (5) – Tools and Equipment Reference Code. Column (5) specifies, by code, those common tool sets (not individual tools), common Test, Measurement and Diagnostic Equipment (TMDE), and special tools, special TMDE and special support equipment required to perform the designated function. Codes are keyed to the entries in the tools and test equipment table. Column (6) – Remarks Code. When applicable, this column contains a letter code, in alphabetical order which is keyed to the remarks table entries. Explanation of Columns in the Tools and Test Equipment Requirements Column (1) – Tools or Test Equipment Reference Code. The tool or test equipment reference code correlates with a code used in column (5) of the MAC. Column (2) – Maintenance Level. The lowest level of maintenance authorized to use the tool or test equipment. Column (3) – Nomenclature. Name or identification of the tool or test equipment. Column (4) – National Stock Number (NSN). The NSN of the tool or test equipment Column (5) – Tool Number. The manufacture’s part number, model number, or type number.


TM 9-1005-338-13&P 0033 00 MAINTENANCE ALLOCATION CHART (MAC) (cont) Explanation of Columns in the Remarks Column (1) – Remarks Code. The code recorded in column (6) of the MAC. Column (2) – Remarks. This column lists information pertinent to the maintenance function being performed as indicated in the MAC.


TM 9-1005-338-13&P 0034 00 MAINTENANCE ALLOCATION CHART

Table 1. Maintenance Allocation Chart for Shotgun, Model 500 and Model 590

(4)

MAINTENANCE LEVEL UNIT DS GS DEPOT

(1)

GROUP NUMBER

(2)

COMPONENT/ ASSEMBLY

(3)

MAINTENANCE FUNCTION C O F H D

(5) TOOLS AND

EQUIPMENT REF CODE

(6)

REMARKS

00 Shotgun, 12 Gauge, Model 500 (P/N MOD500)

and Shotgun, 12 Gauge, Model 590 (P/N 52660)

Inspect Service Overhaul

0.1 0.1

0.1 0.1

0.1

3.6

1, 2

01 Stock Assembly (P/N 14762MIL)

and Pistol Grip Assembly (P/N 7995P)

Inspect Service Repair

0.1 0.1

0.1 0.1

0.1

0.2

1, 2

02 Receiver Assembly (P/N 10171MIL)


0.1 0.1

0.1 0.1

0.1

0.3

1, 2

0201 Safety Assembly (NPN)


1,2

03 Barrel Assembly (P/N 3907P)

and Barrel Assembly (P/N 16019P)


0.1 0.1

0.1 0.1

0.1

0.2

1, 2

04 Fore End Slide Assembly (P/N MOSS-5)


0.1 0.1

0.1 0.1

0.1

0.2

1, 2 A

05 Bolt Assembly (P/N 6706P)

Inspect Service Replace Repair

0.1 0.1

0.1 0.1

0.1

0.2

1, 2


TM 9-1005-338-13&P 0034 00 MAINTENANCE ALLOCATION CHART (cont)

Table 2. Tools and Test Equipment for Shotguns

(1) TOOL OR

TEST EQUIPMENT REF CODE

(2)

MAINTENANCE LEVEL

(3)

NOMENCLATURE

(4)

NATIONAL STOCK NUMBER

(5)

TOOL NUMBER

1 O/F Tool Kit, Small Arms Repairman

5180-01-462-4254 SC 5180-95-B71

2 F Shop Set, Small Arms: Field Maintenance, Basic Less Power

4933-00-754-0664 SC 4933-95-CL-A11

Table 3. Remarks for Shotgun

Reference Code Remarks

A See manufactured item 1, WP 0029 00.


TM 9-1005-338-13&P 0035 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST (INCLUDING DEPOT MAINTENANCE REPAIR PARTS FOR MOSSBERG SHOTGUNS INTRODUCTION SCOPE This RPSTL lists and authorizes spares and repair parts; special tools; special test, measurement and diagnostic equipment (TMDE); and other special support equipment required for performance of unit and direct support maintenance of Gun Mounts. It authorizes the requisitioning, issue, and disposition of spares, repair parts, and special tools as indicated by the source, maintenance, and recoverability (SMR) Code. GENERAL In addition to the Introduction work package, this RPSTL is divided into the following work packages. 1. Repair Parts List Work Packages. Work packages containing lists of spares and repair parts authorized by this RPSTL for use in the performance of maintenance. These work packages also include parts which may be removed for replacement of the authorized parts. Parts lists are composed of functional groups in ascending alphanumeric sequence, with the parts in each group listed in ascending figure and item number sequence. Sending units, brackets, filters and bolts are listed with the component they mount on. Bulk materials are listed by item name in FIG. BULK at the end of the work packages. Repair kits are listed separately in their own functional group and work package. Repair parts for reparable special tools are listed in their own functional group and work package. Repair parts for reparable special tools are also listed in separate work package. Items listed are shown on the associated illustrations. 2. Special Tools List Work packages. Work packages containing list of special tools, special TMDE, and special support equipment authorized by this RPSTL (as indicated by Basis of Issue (BOI) information in the DESCRIPTION AND USABLE ON CODE (UOC) column). Tools that are components of common tool sets and/or Class VII are not listed. 3. Cross-Reference Index Work Packages. There are three cross-reference indexes work packages in this RPSTL: the National Stock Number (NSN) Index work package, the Part Number Index work package, and the Reference Designator Index work package. The National Stock Number Index work package refers you the figure and item number. The Part Number Index work package refers you the figure and item number. The Reference Designator Index work package refers you the figure and item number.


TM 9-1005-338-13&P 0035 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST (INCLUDING DEPOT MAINTENANCE REPAIR PARTS FOR MOSSBERG SHOTGUNS (cont) EXPLANATION OF COLUMNS IN THE REPAIR PARTS LIST AND SPECIAL TOOLS LIST WORK PACKAGES ITEM NO. (Column (1)). Indicates the number used to identify items called out in the illustration. SMR CODE (Column (2)). The SMR code containing supply/requisitioning information, maintenance level authorization criteria, and disposition instruction, as shown in the following breakout:

Source Code

Maintenance Code

Recoverability Code

xx xx x

1st two positions: How to get an item.

3rd position: Who can install, replace, or use the item.

4th position: Who can do complete repair* on the item.

5th position: Who determines disposition action on unserviceable items.

*Complete Repair: Maintenance capacity, capability, and authority to perform all corrective maintenance tasks of the “Repair” function in a use/user environment in order to restore serviceability to a failed item.

Source Code

Application/Explanation

PA

PB

PC

PD

PE

PF

PG

Stock items; use the applicable NSN to requisition/request items with these source codes. They are authorized to the level indicated by the code entered in the 3rd position of the SMR code.

NOTE Items coded PC are subject to deterioration.

KD

KF

KB

Items with these codes are not to be requested/requisitioned individually. They are part of a kit, which is authorized to the maintenance level indicated in the 3rd position of the SMR code. The complete kit must be requisitioned and applied.


TM 9-1005-338-13&P 0035 00

MO – Made at unit/ AVUM level

MF – Made at DS/AVIM level

MH – Made at GS level

ML – Made at SRA

MD – Made at depot

Items with these codes are not to be requested/requisitioned individually. They must be made from bulk material, which is identified by the P/N in the DESCRIPTION AND USABLE ON CODE (UOC) column and listed in the bulk material group work package of the RPSTL. If the item is authorized to you by the 3rd position code of the SMR code, but the source code indicates it is made at a higher level, order the item from the higher level of maintenance.

AO - Assembled by unit/ AVUM level

AF – Assembled by DS/ AVIM level

AH – Assembled by GS level

AL – Assembled by SRA

AD – Assembled by depot

Items with these codes are not to be requested/requisitioned individually. The parts that make up the assembled item must be requisitioned or fabricated and assembled at the level of maintenance indicated by the source code. If the 3rd position of the SMR code authorizes you to replace the item, but the source code indicates the item is assembled at a higher level, order the item from the higher level of maintenance.

XA - Do not requisition an “XA” coded item. Order the next higher assembly. (Refer to NOTE

below.)

XB - If an item is not available from salvage, order it using the CAGEC and P/N.

XC - Installation drawings, diagrams, instruction sheets, field service drawings; identified by

manufacturer’s P/N.

XD - Item is not stocked. Order and XD-coded item through normal supply channels using the CAGEC and P/N given, if no NSN is available.

NOTE

Cannibalization or controlled exchange, when authorized, may be used as a source of supply for items with the above source codes except for those items source coded “XA” or those aircraft support items restricted by requirements of AR 750-1.


TM 9-1005-338-13&P 0035 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST (INCLUDING DEPOT MAINTENANCE REPAIR PARTS FOR MOSSBERG SHOTGUNS (cont) EXPLANATION OF COLUMNS IN THE REPAIR PARTS LIST AND SPECIAL TOOLS LIST WORK PACKAGES (cont) Maintenance Code. Maintenance codes tell you the level(s) of maintenance authorized to use and repair support items. The maintenance codes are entered in the third and forth positions of the SMR code as follows: Third Position. The maintenance code entered in the third position tells you the lowest maintenance level authorized to remove, replace, and use an item. The maintenance code entered in the third position will indicate authorization to the following levels of maintenance: Maintenance Code


C - Crew or operator maintenance done within unit/AVUM maintenance.

O - Unit level/AVUM maintenance can remove, replace, and use the item.

F - Direct support/AVIM maintenance can remove, replace, and use the item.

H - General support maintenance can remove, replace, and use the item.

L - Specialized repair activity can remove, replace, and use the item.

D - Depot can remove, replace, and use the item. Forth Position. The maintenance code entered in the forth position tells you whether or not the item is to be repaired and identifies the lowest maintenance level with the capability to do complete repair (perform all authorized repair functions). Maintenance Code


O - Unit/AVUM is the lowest level that can do complete repair of the item.

F - Direct support/AVIM is the lowest level that can do complete repair of the item.

H - General support is the lowest level that can do complete repair of the item.

L - Specialized repair activity is the lowest level that can do complete repair of the item.

D - Depot is the lowest level that can do complete repair of the item.

Z - Non-reparable. No repair is authorized.

B No repair is authorized. No parts or special tools are authorized for maintenance of “B” coded item. However, the item may be reconditioned by adjusting, lubricating, etc., at the user level.


TM 9-1005-338-13&P 0035 00 Recoverability Code. Recoverability codes are assigned to items to indicate the disposition action on unserviceable items. The recoverability code is shown in the fifth position of the SMR code as follows: Recoverability Code


Z - Non-reparable item. When unserviceable, condemn and dispose of the item at the level of maintenance shown in the third position of the SMR code.

O - Reparable item. When uneconomically reparable, condemn and dispose of the item at the unit support level.

F - Reparable item. When uneconomically reparable, condemn and dispose of the item at the direct support level.

H - Reparable item. When uneconomically reparable, condemn and dispose of the item at the general support level.

D - Reparable item. When beyond lower level repair capability, return to depot. Condemnation and disposal of item are not authorized below depot level.

L - Reparable item. Condemnation and disposal of item are not authorized below Specialized Repair Activity (SRA).

A - Item requires special handling or condemnation procedures because of specific reasons (such as precious metal content, high dollar value, critical material, or hazardous material). Refer to appropriate manuals/directives for specific instructions.

NSN (Column (3)). The NSN for the item is listed in this column. CAGEC (Column (4)). The Commercial and Government Entity Code (CAGEC) is a five-digit code which is used to identify the manufacture, distributor, or Government agency/activity that supplies the item. PART NUMBER (Column (5)). Indicates the primary number used by the manufacturer (individual company, firm, corporation, or Government activity), which controls the design and characteristics of the item by means of its engineering drawings, specifications, standards, and inspection requirements to identify an item or range of items.

NOTE When you use an NSN to requisition an item, the item you receive may have a different P/N from the number listed.

DESCRIPTION AND USABLE ON CODE (UOC) (Column (6)). This column includes the following information: 1. The federal item name, and when required, a minimum description to identify the item. 2. P/N’s of bulk materials are referenced in this column in the line entry to be manufactured or

fabricated. 3. Hardness Critical Item (HCI). A support item that provides the equipment with special protection

from electromagnetic pulse (EMP) damage during a nuclear attack. 4. The statement “END OF FIGURE” appears just below the last item description in column (6) for a

given figure in both the repair parts list and special tools list work packages.


TM 9-1005-338-13&P 0035 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST (INCLUDING DEPOT MAINTENANCE REPAIR PARTS FOR MOSSBERG SHOTGUNS (cont) EXPLANATION OF CROSS-REFERENCE INDEXES WORK PACKAGES FORMAT AND COLUMNS (cont) QTY (Column (7)). The QTY (quantity per figure) column indicates the quantity of the item used in the breakout shown on the illustration/figure, which is prepared for a functional group, sub-functional group, or an assembly. A “V” appearing in this column instead of a quantity indicates that the quantity is variable and quantity may change from application to application. EXPLANATION OF CROSS-REFERENCE INDEXES WORK PACKAGES FORMAT AND COLUMNS 1. National Stock Number (NSN) Index Work Package. STCOK NUMBER Column. This column lists the NSN in National item identification number (NIIN) sequence. The NIIN consists of the last nine digits of the NSN.

NSN (e.g., 5385-01-574-1476)

NIIN

When using this column to locate an item, ignore the first four digits of the NSN. However, the complete NSN should be used when ordering items by stock number.

FIG. Column. This column lists the number of the figure where the item is identified/located. The figures are in numerical order in the repair parts list and special tools list work packages. ITEM Column. The item number identifies the item associated with the figure listed in the adjacent FIG. Column. This item is also identified by the NSN listed on the same line. 2. Part Number (P/N) Index Work Package. P/ns in this index are listed in ascending alphanumeric sequence (vertical arrangement of letter and number combinations which places the first letter of digit of each group in order A through Z, followed by numbers 0 through 9 and each following letter or digit in like order. PART NUMBER Column. Indicates the P/N assigned to the item/ FIG. Column. This column lists the number of the figure where the item is identified/located in the repair parts list and special tools list work packages. ITEM Column. The item number is the number assigned to the item as it appears in the figure referenced in the adjacent figure number column. Reference Designator Index Work Package. Reference designators in this index are listed in ascending alphanumeric sequence (vertical arrangement of letter and number combinations which places the first letter of digit of each group in order A through Z, followed by numbers 0 through 9 and each following letter or digit in like order. REFERENCE DESIGNATOR Column. Indicates the reference designator assigned to the item. FIG. Column. This column lists the number of the figure where the item is identified/located in the repair parts list and special tools list work packages. ITEM Column. The item number is the number assigned to the item as it appears in the figure referenced in the adjacent figure number column.


TM 9-1005-338-13&P 0035 00 SPECIAL INFORMATION UOC. The UOC appears in the lower left corner of the Description Column heading. Usable on codes are shown as “UOC:…” in the Description Column (justified left) on the first line under the applicable item/ nomenclature. Uncoded items are applicable to all models. Identification of the UOCs used in the RPSTL are:

Code Used On

AL3 Mossberg, 12 Gauge, Shotgun, Model 500

AJ2 Mossberg, 12 Gauge, Shotgun, Model 590 Fabrication Instructions. Bulk materials required to manufacture items are listed in the bulk material functional group of the RPSTL. Part numbers for bulk material are also referenced in the Description Column of the line item entry for the item to be manufactured/fabricated. Detailed fabrication instructions for the items source coded to be manufactured or fabricated are found in this manual. HOW TO LOCATE REPAIR PARTS 1. When NSNs or P/Ns Are Not Known. First. Using the table of contents, determine the assembly group to which the item belongs. This is necessary since figures are prepared for assembly groups and sub-assembly groups, and lists are divided into the same groups. Second. Find the figure covering the functional group or the sub-functional group to which the item belongs. Third. Identify the item on the figure and note the number(s). Fourth. Look in the repair parts list work packages for the figure and item numbers. The NSNs and part numbers are on the same line as the associated item numbers. 2. When NSN Is Known. First. If you have the NSN, look in the STOCK NUMBER column of the NSN index work package. The NSN is arranged in NIIN sequence. Note the figure and item number next to the NSN. Second. Turn to the figure and locate the item number. Verify that the item is the one you are looking for. 3. When P/N Is Known. First. If you have the P/N and not the NSN, look in the PART NUMBER column of the P/N index work package. Identify the figure and item number. Second. Look up the item on the figure in the applicable repair parts list work package.


TM 9-1005-338-13&P 0035 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST (INCLUDING DEPOT MAINTENANCE REPAIR PARTS FOR MOSSBERG SHOTGUNS (cont) HOW TO LOCATE REPAIR PARTS (cont) 4. When Reference Designator Is Known. First. If you know the reference designator, look in the REFERENCE DESIGNATOR column of the reference designator index work package. Note the figure and item number. Second. Turn to the figure and locate the item number. Verify that the item is the one you are looking for. ABBREVIATIONS. N/A


TM 9-1005-338-13&P 0036 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS LIST FOR SHOTGUN, 12-GAUGE, MOSSBERG, MODEL 500, NSN 1005-01-085-1032, P/N MOD500 SHOTGUN, 12-GAUGE, MOSSBERG, MODEL 590, NSN 1005-01-251-8578, P/N MOD590

1

2

3

4

5

67

8

2MB0049

MODEL 500

Figure 1. Shotgun, 12-Gauge, Mossberg, Model 500, P/N MOD500 (1 of 2)


TM 9-1005-338-13&P 0036 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS LIST FOR SHOTGUN, 12-GAUGE, MOSSBERG, MODEL 500, NSN 1005-01-085-1032, P/N MOD500 SHOTGUN, 12-GAUGE, MOSSBERG, MODEL 590, NSN 1005-01-251-8578, P/N MOD590 (cont)

1

2

3

4

5

67

8

2MB0050

9

MODEL 590

Figure 1. Shotgun, 12-Gauge, Mossberg, Model 590, P/N MOD590 (2 of 2)


TM 9-1005-338-13&P 0036 00

(1) ITEM NO.

(2) SMR

CODE

(3)

NSN

(4)

CAGEC

(5) PART

NUMBER

(6) DESCRIPTION AND USABLE ON CODE (UOC)

(7)

QTY GROUP 00

FIGURE 1. SHOTGUN, 12-GAUGE, MOSSBERG, M500, P/N MOD500; SHOTGUN, 12-GAUGE, MOSSBERG, M590, P/N MOD590

1 XAFFF 41758 10171MIL RECEIVER ASSEMBLY SEE FIG. 2 FOR BRKDWN UOC: AL3..................................................

1 1 XAFFF 41758 10171A1 RECEIVER ASSEMBLY

SEE FIG. 2 FOR BRKDWN UOC: AJ2 ..................................................

1 2 PAOFF 1005-01-512-9286 41758 3907P BARREL ASSEMBLY

SEE FIG. 3 FOR BRKDWN UOC: AL3..................................................

1 2 PAOFF 1005-01-523-1267 41758 16019P BARREL ASSEMBLY

SEE FIG. 3 FOR BRKDWN UOC: AJ2 ..................................................

1 3 AOOOO 41758 MOSS-05 FORE END SLIDE ASSEMBLY

SEE FIG. 4 FOR BRKDWN UOC: AJ2, AL3..........................................

1 4 PAFFF 1005-01-512-2731 41758 6706P BOLT ASSEMBLY


1 5 PAFZZ 1005-01-512-2734 41758 6443P BOLT SLIDE

UOC: AJ2, AL3..........................................

1 6 PAOZZ 5315-01-512-2729 41758 1580P PIN, TRIGGER HOUSING

UOC: AJ2, AL3..........................................

1 7 PAFZZ 1005-01-520-5995 41758 13229MIL TRIGGER HOUSING ASSEMBLY

UOC: AJ2, AL3..........................................

1 8 PAOOO 1005-01-511-9538 41758 14762MIL STOCK, GUN, SHOULDER


1 9 PAFZZ 1005-01-520-5991 41758 11239P CAP, RETAINING

UOC: AJ2 .................................................

1 END OF FIGURE

END OF WORK PACKAGE

0036 00-3/4blank http://www.emilitarymanuals.com

TM 9-1005-338-13&P 0036 00


TM 9-1005-338-13&P 0037 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS LIST FOR RECEIVER ASSEMBLY, NSNA, P/N 10171MIL; RECEIVER ASSEMBLY, NSNA, P/N 10171A1 AND SAFETY ASSEMBLY, NSNA, NPN



TM 9-1005-338-13&P 0037 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS LIST FOR RECEIVER ASSEMBLY, NSNA, P/N 10171MIL; RECEIVER ASSEMBLY, NSNA, P/N 10171A1 AND SAFETY ASSEMBLY, NSNA, NPN (cont)

1

2

3

4

5

10

11

12

13

14

15

2MB0051

16

9

6

78

M590

6

M500

78

Figure 2. Receiver Assembly, P/N 10171MIL and Safety Assembly, NPN


TM 9-1005-338-13&P 0037 00

(1) ITEM NO.

(2) SMR

CODE

(3)

NSN

(4)

CAGEC

(5) PART

NUMBER


(7)

QTY GROUP 02, 0201

FIGURE 2. RECEIVER ASSEMBLY, P/N 10171MIL; RECEIVER ASEMBLY, P/N 10171A1; AND SAFETY ASSEMBLY, NPN

1 PAFZZ 5360-01-231-0419 41758 11761 SPRING, DETENT SAFETY UOC: AL3, AJ2..............................................

1

2 PAFZZ 1005-01-240-5003 41758 7349 BALL, SAFETY DETENT UOC: AL3, AJ2..............................................

1

3 PAFZZ 5365-01-290-6481 41758 7753 PLATE, SAFETY DETENT UOC: AL3, AJ2..............................................

1

4 PAFZZ 1005-01-285-0624 41758 13049P SAFETY BUTTON UOC: AL3, AJ2..............................................

1

5 PAFZZ 5305-01-523-4871 41758 11125P SCREW, SAFETY BUTTON UOC: AL3, AJ2..............................................

1

6 PAFZZ 1005-01-512-2741 41758 10342P TUBE ASSEMBLY, MAGAZINE, 6-SHOT UOC: AL3......................................................

1 6 PAFZZ 1005-01-520-5993 41758 11241P TUBE ASSEMBLY, MAGAZINE,

9-SHOT UOC: AJ2 ......................................................

1 7 PAFZZ 1005-01-513-3321 41758 1554P FOLLOWER, CARTRIDGE

UOC: AL3, AJ2..............................................

1 8 PAFZZ 5360-01-231-0420 41758 1553 SPRING, MAGAZINE

UOC: AL3......................................................

1 8 PAFZZ 5360-01-285-0626 41758 11443 SPRING, MAGAZINE

UOC: AJ2 ......................................................

1 9 PAFZZ 1005-01-391-3863 41758 12392P RETAINER, CATCH, MAGAZINE

UOC: AJ2 ......................................................1

10 PAFZZ 1005-01-517-4151 41758 1538P EJECTOR UOC: AL3, AJ2..............................................

1

11 PAFZZ 5305-01-523-6533 41758 1539P SCREW, EJECTOR UOC: AL3, AJ2..............................................

1

12 PAFZZ 1005-01-512-2726 41758 1765P ELEVATOR UOC: AL3, AJ2..............................................

1

13 PAFZZ 1005-01-512-2730 41758 7557P CARTRIDGE STOP UOC: AL3, AJ2..............................................

1

14 PAFZZ 1005-01-512-2725 41758 7607P CARTRIDGE INTERRUPTER UOC: AL3, AJ2..............................................

1

15 XAFFF 41758 M590-2 RECEIVER UOC: AJ2 ......................................................

1

15 XAFFF 41758 MOD500-10 RECEIVER UOC: AL3......................................................

1

16 PAFZZ 1005-01-512-2728 41758 7441P LOCK, GUN, SAFETY UOC: AL3, AJ2.........................................

1

END OF FIGURE

END OF WORK PACKAGE


TM 9-1005-338-13&P 0037 00


TM 9-1005-338-13&P 0038 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS LIST FOR BARREL ASSEMBLY, NSNA, P/N 16019P BARREL ASSEMBLY, NSN 1005-01-512-9286, P/N 3907P



TM 9-1005-338-13&P 0038 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS LIST FOR BARREL ASSEMBLY, NSNA, P/N 16019P BARREL ASSEMBLY, NSN 1005-01-512-9286, P/N 3907P (cont)

1

2

3

7

2

1

M500

M590

8

9

10

2MB0052

4

5

4

5

6

Figure 3. Barrel Assembly, P/N 16019P; Barrel Assembly, P/N 3907P


TM 9-1005-338-13&P 0038 00

(1) ITEM NO.

(2) SMR

CODE

(3)

NSN

(4)

CAGEC

(5) PART

NUMBER


(7)

QTY GROUP 03

FIGURE 3. BARREL ASSEMBLY, P/N 16019P; AND BARREL ASSEMBLY, P/N 3907P

1 XAFZZ 41758 M500BRL-1 BARREL UOC: AL3....................................................

1

1 XAFZZ 41758 M590BRL-1 BARREL UOC: AJ2 ....................................................

1

2 PAFZZ 1005-01-523-3929 41758 13443P SIGHT, FRONT SIGHT BEAD UOC: AL3....................................................

1

2 PAFZZ 1005-01-225-3817 41758 7457 SIGHT, FRONT SIGHT BEAD UOC: AJ2 ....................................................

1

3 PAFZZ 5305-01-512-2732 41758 3874P SCREW ASSEMBLY UOC: AL3....................................................

1

4 PAOZZ 1005-01-512-2733 41758 12383P FRONT SWIVEL POST KIT ........................ 1 5 PAOZZ 1005-01-512-4530 41758 12032MIL SWIVEL ASSEMBLY .................................. 1 6 PAFZZ 5325-01-231-0546 41758 5393 RING, RETAINING

UOC: AL3....................................................

1 7 PAOZZ 5310-01-294-3530 41758 10494 NUT, SELF-LOCKING

UOC: AJ2 ....................................................

2 8 PAOZZ 5306-01-386-5356 41758 11588 SCREW

UOC: AJ2 ....................................................

2 9 PAOZZ 5365-01-286-5186 41758 12086 SPACER, PLATE, HEAT SHIELD

UOC: AJ2 ....................................................

1 10 PAOZZ 1005-01-523-1271 41758 16335P HEAT SHIELD

UOC: AJ2 ....................................................

1 END OF FIGURE

END OF WORK PACKAGE


TM 9-1005-338-13&P 0038 00


TM 9-1005-338-13&P 0039 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS LIST FOR FORE END SLIDE ASSEMBLY, NSNA, P/N MOSS-05

4

3

1

2

2MB0053

Figure 4. Fore End Slide Assembly, P/N MOSS-05

(1) ITEM NO.

(2) SMR

CODE

(3)

NSN

(4)

CAGEC

(5) PART

NUMBER


(7)

QTY GROUP 04

FIGURE 4. FORE END SLIDE ASSEMBLY, P/N MOSS-05

1 PAFZZ 5360-01-512-2740 PAOZZ 13484P SPRING, ANTI-RATTLE UOC: AL3....................................................

1

2 PAFZZ 1005-01-512-4413 PAOZZ 11603P SLIDE ASSEMBLY, ACTION UOC: AL3, AJ2............................................

1

3 PAFZZ 1005-01-285-0611 PAOZZ 10462 FORE END, SYSTHETIC RUBBER UOC: AL3, AJ2............................................

1

4 PAFZZ 1005-01-513-0733 PAOZZ 3408P NUT, ACTION SLIDE TUBE UOC: AL3, AJ2............................................

1

END OF FIGURE

END OF WORK PACKAGE


TM 9-1005-338-13&P 0039 00


TM 9-1005-338-13&P 0040 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS LIST FOR BOLT ASSEMBLY, NSN 1005-01-512-2731, P/N 6706P



TM 9-1005-338-13&P 0040 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS LIST FOR BOLT ASSEMBLY, NSN 1005-01-512-2731, P/N 6706P

1

2

3

45

6

7

8

9

10

1

3

11

2MB0054

Figure 5. Bolt Assembly, P/N 6706P


TM 9-1005-338-13&P 0040 00

(1) ITEM NO.

(2) SMR

CODE

(3)

NSN

(4)

CAGEC

(5) PART

NUMBER


(7)

QTY GROUP 05

FIGURE 5. BOLT ASSEMBLY, P/N 6706P

1 PAFZZ 5315-01-512-9285 41758 1544P PIN, RETAINING UOC: AJ2, AL3...........................................

2

2 PAFZZ 5315-01-512-9283 41758 1531P PIN, BOLT LOCK UOC: AJ2, AL3...........................................

1

3 PAFZZ 5360-01-285-0145 41758 7330 SPRING, EXTRACTOR UOC: AJ2, AL3...........................................

2

4 PAFZZ 1005-01-512-2735 41758 12762P EXTRACTOR LH UOC: AJ2, AL3...........................................

1

5 PAFZZ 1005-01-512-4412 41758 1599P PIN, EXTRACTOR LH UOC: AJ2, AL3...........................................

1

6 XAFZZ 41758 3433P BOLT UOC: AJ2, AL3...........................................

1

7 PAFZZ 1005-01-512-2739 41758 12761P EXTRACTOR RH UOC: AJ2, AL3...........................................

1

8 PAFZZ 1005-01-512-2738 41758 16106P LOCK, BOLT UOC: AJ2, AL3...........................................

1

9 PAFZZ 5360-01-512-2742 41758 14629MIL SPRING, FIRING PIN UOC: AJ2, AL3...........................................

1

10 PAFZZ 5310-01-512-2736 41758 7429P WASHER, FIRING PIN UOC: AJ2, AL3...........................................

1

11 PAFZZ 1005-01-512-2737 41758 11793P PIN, FIRING UOC: AJ2, AL3...........................................

1

END OF FIGURE

END OF WORK PACKAGE


TM 9-1005-338-13&P 0040 00


TM 9-1005-338-13&P 0041 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS LIST FOR STOCK, GUN, SHOULDER, NSN 1005-01-511-9538, P/N 14762MIL



TM 9-1005-338-13&P 0041 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS LIST FOR STOCK, GUN, SHOULDER, NSN 1005-01-511-9538, P/N 14762MIL (cont)

1

23

4

5

6

7

8

Figure 6. Stock, Gun, Shoulder, P/N 14762MIL


TM 9-1005-338-13&P 0041 00

(1) ITEM NO.

(2) SMR

CODE

(3)

NSN

(4)

CAGEC

(5) PART

NUMBER


(7)

QTY GROUP 01

FIGURE 6. STOCK, GUN, SHOULDER, P/N 14762MIL

1 PAOZZ 5305-01-284-7568 41758 11789 STOCK, BOLT UOC: AL3, AJ2.........................................

1

2 PAOZZ 5310-01-512-2724 41758 7613P WASHER, LOCK UOC: AL3, AJ2.........................................

1

3 PAOZZ 5310-01-512-2727 41758 1571P WASHER UOC: AL3, AJ2.........................................

1

4 XAOZZ 41758 16079 BUTTSTOCK, SYSTHETIC UOC: AL3, AJ2.........................................

1

5 PAOZZ 1005-01-512-4414 41758 6641P SWIVEL POST UOC: AL3, AJ2.........................................

1

6 PAOZZ 1005-01-152-4530 41758 12032MIL SWIVEL ASSEMBLY, REAR UOC: AL3, AJ2.........................................

1

7 PAOZZ 1005-01-518-4506 41758 16080 PAD, RECOIL UOC: AL3, AJ2.........................................

1

8 PAOZZ 5310-01-511-9536 41758 171P SCREW, MACHINE UOC: AL3, AJ2.........................................

2

END OF FIGURE

END OF WORK PACKAGE


TM 9-1005-338-13&P 0041 00


TM 9-1005-338-13&P 0042 00 UNIT AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS LIST FOR GRIP, PISTOL, ASSEMBLY, NSN 1005-01-512-2743, P/N 7995P

2MB0057

1

3

2

4

5

Figure 7. Grip, Pistol Assembly, P/N 7995P

(1) ITEM NO.

(2) SMR

CODE

(3)

NSN

(4)

CAGEC

(5) PART

NUMBER


(7)

QTY GROUP 01

FIGURE 7. GRIP, PISTOL ASSEMBLY, P/N 7995P

1 PAOZZ 1005-01-525-5734 41758 7733P SCREW, HEX. HEAD................................. 1 2 PAOZZ 5310-01-512-2724 41758 7613P LOCK-WASHER......................................... 1 3 PAOZZ 5310-01-512-2727 41758 1571P WASHER ................................................... 1 4 PAOZZ 1005-01-512-4414 41758 6641P SWIVEL...................................................... 1 5 XAOZZ 41758 7679 GRIP, PISTOL............................................ 1 END OF FIGURE

END OF WORK PACKAGE


TM 9-1005-338-13&P 0042 00


TM 9-1005-338-13&P 0043 00 CROSS REFERENCE LIST – PART NUMBER

PART NUMBER


FIG.

ITEM

10171A1 1 1 10171MIL 1 1 10342P 1005-01-512-2741 2 6 10462 1005-01-285-0611 4 3 10494 5310-01-294-3530 3 7 11125P 5305-01-523-4871 2 5 11239P 1005-01-520-5991 1 9 11241P 1005-01-520-5993 2 6 11443 5360-01-285-0626 2 8 11588 5306-01-386-5356 3 8 11603P 1005-01-512-4413 4 2 11761 5360-01-231-0419 2 1 11789 5305-01-284-7568 6 1 11793P 1005-01-512-2737 5 11 12032MIL 1005-01-512-4530 3 4 12032MIL 1005-01-152-4530 6 6 12086 5365-01-286-5186 3 9 12383P 1005-01-512-2733 3 5 12392P 1005-01-391-3863 2 9 12761P 1005-01-512-2739 5 7 12762P 1005-01-512-2735 5 4 13049P 1005-01-285-0624 2 4 13229MIL 1005-01-520-5995 1 7 13443P 1005-01-523-3929 3 2 13484P 5360-01-512-2740 4 1 14629MIL 5360-01-512-2742 5 9 14762MIL 1005-01-511-9538 1 8 1531P 5315-01-512-9283 5 2 1538P 1005-01-517-4151 2 10 1539P 5305-01-523-6533 2 11 1544P 5315-01-512-9285 5 1 1553 5360-01-231-0420 2 8 1554P 1005-01-513-3321 2 7 1571P 5310-01-512-2727 6 3 1571P 5310-01-512-2727 7 3 1580P 5315-01-512-2729 1 6 1599P 1005-01-512-4412 5 5


TM 9-1005-338-13&P 0043 00 CROSS REFERENCE LIST – PART NUMBER (cont)

PART NUMBER


FIG.

ITEM

16019P 1005-01-523-1267 1 2 16079 6 4 16080 1005-01-518-4506 6 7 16106P 1005-01-512-2738 5 8 16335P 1005-01-523-1271 3 10 171P 5310-01-511-9536 6 8 1765P 1005-01-512-2726 2 12 3408P 1005-01-513-0733 4 4 3433P 5 6 3874P 5305-01-512-2732 3 3 3907P 1005-01-512-9286 1 2 5393 5325-01-231-0546 3 6 6443P 1005-01-512-2734 1 5 6641P 1005-01-512-4414 6 5 7 4 6706P 1005-01-512-2731 1 4 7330 5360-01-285-0145 5 3 7349 1005-01-240-5003 2 2 7429P 5310-01-512-2736 5 10 7441P 1005-01-512-2728 2 16 7457 1005-01-225-3817 3 2 7557P 1005-01-512-2730 2 13 7607P 1005-01-512-2725 2 14 7613P 5310-01-512-2724 6 2 7 2 7679 7 5 7733P 1005-01-525-5764 7 1 7753 5365-01-290-6481 2 3 7995P 1005-01-512-2743 7 M500BRL-1 3 1 M590-2 2 15 M590BRL-1 3 1 MOD500 1005-01-085-1032 1 MOD500-10 2 15 MOD590 1005-01-251-8578 1 MOSS-05 1 3

END OF WORK PACKAGE


TM 9-1005-338-13&P 0044 00 CROSS REFERENCE LIST – NATIONAL STOCK NUMBER

PART NUMBER


FIG.

ITEM

6641P 1005-01-512-4414 7 4 7733P 1005-01-525-5764 7 1 MOD500 1005-01-085-1032 1 12032MIL 1005-01-152-4530 6 6 7457 1005-01-225-3817 3 2 1553 5360-01-231-0420 2 8 11761 5360-01-231-0419 2 1 7349 1005-01-240-5003 2 2 MOD590 1005-01-251-8578 1 11789 5305-01-284-7568 6 1 7330 5360-01-285-0145 5 3 10462 1005-01-285-0611 4 3 13049P 1005-01-285-0624 2 4 11443 5360-01-285-0626 2 8 5393 5325-01-231-0546 3 6 12086 5365-01-286-5186 3 9 7753 5365-01-290-6481 2 3 10494 5310-01-294-3530 3 7 11588 5306-01-386-5356 3 8 12392P 1005-01-391-3863 2 9 171P 5310-01-511-9536 6 8 14762MIL 1005-01-511-9538 1 8 7613P 5310-01-512-2724 6 2 7 2 7607P 1005-01-512-2725 2 14 1765P 1005-01-512-2726 2 12 1571P 5310-01-512-2727 6 3 7 3 7441P 1005-01-512-2728 2 16 1580P 5315-01-512-2729 1 6 7557P 1005-01-512-2730 2 13 6706P 1005-01-512-2731 1 4 3874P 5305-01-512-2732 3 3 12383P 1005-01-512-2733 3 5 6443P 1005-01-512-2734 1 5 12762P 1005-01-512-2735 5 4 7429P 5310-01-512-2736 5 10 11793P 1005-01-512-2737 5 11


TM 9-1005-338-13&P 0044 00 CROSS REFERENCE LIST – NATIONAL STOCK NUMBER (cont)

PART NUMBER


FIG.

ITEM

16106P 1005-01-512-2738 5 8 12761P 1005-01-512-2739 5 7 13484P 5360-01-512-2740 4 1 10342P 1005-01-512-2741 2 6 14629MIL 5360-01-512-2742 5 9 7995P 1005-01-512-2743 7 1599P 1005-01-512-4412 5 5 11603P 1005-01-512-4413 4 2 6641P 1005-01-512-4414 6 5 12032MIL 1005-01-512-4530 3 4 1531P 5315-01-512-9283 5 2 1544P 5315-01-512-9285 5 1 3907P 1005-01-512-9286 1 2 3408P 1005-01-513-0733 4 4 1554P 1005-01-513-3321 2 7 1538P 1005-01-517-4151 2 10 16080 1005-01-518-4506 6 7 11239P 1005-01-520-5991 1 9 11241P 1005-01-520-5993 2 6 13229MIL 1005-01-520-5995 1 7 16019P 1005-01-523-1267 1 2 13443P 1005-01-523-3929 3 2 11125P 5305-01-523-4871 2 5 16335P 1005-01-523-1271 3 10

1539P 5305-01-523-6533 2 11

END OF WORK PACKAGE


TM 9-1005-338-13&P 0045 00 COMPONENTS OF THE END ITEM AND BASIC ISSUE ITEMS This work package lists components of the end item and basic issue items for the shotgun to help you inventory items required for safe and effective operation. The Components of the End Item (COEI) and Basic Issue Items (BII) lists are divided into the following: Components of the End Item (COEI): This is for informational purposes only and is not authority to requisition replacements. These items are part of the end item but are removed and separately packaged for transportation or shipment. As part of the end item, these items must be with the end item whenever it is issued or transferred between property accounts. Illustrations are furnished to assist you in identifying the items. These are the minimum essential items required to place the machine gun in operation, to operate it, and to perform emergency repairs. Although shipped separately packaged, BII must be with the machine gun during operation and whenever it is transferred between property accounts. The illustrations will assist you with hard to identify items. This manual is your authority to request/ requisition replacement BII, based on TOE/MTOE authorization of the end item. EXPLANATION OF COLUMNS. The following provide an explanation of columns found in the tabular listings: Column (1) – Illus. Number, gives you the number of the item illustrated. Column (2) – National Stock Number, the stock number of the item to be used for requisitioning purposes. Column (3) – Description and Usable On Code, identifies the Federal item name (in capital letters) followed by a minimum description when needed. The last line below the description is the CAGEC (in parenthesis) and the part number. If the item you need is not the same for different models of the equipment, a Usable On Code will appear on the right side of the description column on the same line as the part number. These codes are identified

Code Used On

AJ2 Shotgun, 12-Gauge, Mossberg Model M590

Al3 Shotgun, 12-Gauge, Mossberg Model M500 Column (4) – U/M, indicates how the item is issued for the National Stock Number shown in column (2). Column (5) – Qty Rqd, indicates the quantity required. COMPONENTS OF THE END ITEM

Table 1. Components of the End Item

(1) ILLUS

NUMBER

(2) NATIONAL STOCK

NUMBER

(3) DESCRIPTION CAGEC AND PART NUMBER

USABLE

ON CODE

(4)

U/M

(5) QTY RQD

1 1005-01-216-4510 SLING, BLACK NYLON (19200) 12624561

EA 1

1

2MB0055


TM 9-1005-338-13&P 0045 00 COMPONENTS OF THE END ITEM AND BASIC ISSUE ITEMS (cont) BASIC ISSUE ITEMS There are no Basic Issue Items for these shotguns.

END OF WORK PACKAGE


TM 9-1005-338-13&P 0046 00 ADDITIONAL AUTHORIZATION LIST (AAL) INTRODUCTION Scope This work package lists additional items you are authorized for the support of your shotgun. General This list identifies items that do not have to accompany the mount and that do not have to be turned in with it. These items are authorized to you by CTA, MTOE, TDA, or JTA. Explanation of Columns in the AAL Column (1) – National Stock Number (NSN). Identifies the stock number of the item to be used for requisitioning purposes. Column (2) – Description, Commercial and Government Entity Code, and Part Number (CAGEC), and Part Number (P/N). Identifies the Federal item name (in all Capital letters) followed by a minimum description when needed. The last line below the description is the CAGEC (in parentheses) and the part number. Column (3) – Usable On Code. When applicable, gives you a code if the item you need is not the same for different models of equipment. These codes are identified below.

Code Used On

AJ2 Shotgun, 12-Gauge, Mossberg Model M590

Al3 Shotgun, 12-Gauge, Mossberg Model M500 Column (4) – Unit of Issue (U/I). Indicates the physical measurement or count of the item as issued per the National Stock Number shown in column (1). Column (5) – Qty Recm. Indicates the quantity recommended.


TM 9-1005-338-13&P 0046 00 ADDITIONAL AUTHORIZATION LIST (AAL)

Table 1. Additional Authorization List

(1) ILLUS

NUMBER

(2) NATIONAL STOCK

NUMBER

(3) DESCRIPTION CAGEC AND PART NUMBER

USABLE

ON CODE

(4)

U/M

(5) QTY RQD

1 1005-01-455-0565 CLEANING KIT, GUN (01VS3) 410-8

KT 1

2 8465-00-261-6944 CASE, SHOTGUN, AMMUNITION (81349) MIL-C-1690

KT 1

3 1005-01-512-2743 GRIP, PISTOL, ASSEMBLY (41758) 7995P

EA 1

END OF WORK PACKAGE


TM 9-1005-338-13&P 0047 00 EXPENDABLE AND DURABLE ITEMS LIST INTRODUCTION Scope This work package lists expendable and durable items that you will need to operate and maintain the Shotgun. This list is for information only and is not authority to requisition the listed items. These items are authorized to you by CTA 50-970, Expendable /Durable Items (Except Medical, Class V Repair Parts, and heraldic Items), or CTA 8-100, Army Medical Department Expendable/Durable Items. Explanation of Columns in the Expendable/Durable Items List Column (1) – Item Number. This number is assigned to the entry in the list and is listed in the narrative instructions to identify the item (e.g., Use brake fluid (item 5, WP 0098 00.). Column (2) – Level. This column identifies the lowest level of maintenance that requires the listed item.

C – Operator/Crew O – Unit Maintenance F – Direct Support Maintenance

Column (3) – National Stock Number (NSN). This is the NSN assigned to the item which you can use to requisition it. Column (4) – Item Name, Description, Commercial and Government Entity Code (CAGEC), and Part Number (P/N). This column identifies the other information you need to identify the item. Column (5) – Unit of Measure. This code shows the physical measurement or count of an item, such as gallon, dozen, gross, etc.


TM 9-1005-338-13&P 0047 00 EXPENDABLE AND DURABLE ITEMS LIST (cont) EXPENDABLE AND DURABLE ITEMS LIST

Table 1. Expendable /Durable Items List

(1) ITEM

NUMBER

(2)

LEVEL

(3) NATIONAL

STOCK NUMBER

(4)

DESCRIPTION

(5)

QTY

1 C 1005-00-494-6602 BRUSH, CLEANING, SMALL ARMS (19204) 8448462

EA

NOTE CLP is an alternative to LSA and LAW. Do not mix lubricants on the same weapon. The weapon must be thoroughly cleaned with cleaning solvent before changing lubricants.

2 C

9150-01-054-6453 9150-01-053-6688

CLEANER, LUBRICANT AND PRESERVATIVE: Grade 2 (CLP) (81349) MIL-PRF-63460 1 pint bottle 1 gal bottle

PT GL

3 C

6850-01-474-2319

CLEANING, SOLVENT (81349) MIL-PRF-680, Type 2 1 gal can

GL

4 C

9150-01-260-2534

LUBRICANT, SOLID FILM (81349) MIL-L-23398 16 oz aerosol can

OZ

5 C

9150-00-292-9689

LUBRICATING OIL, WEAPONS (LAW) (81349) MIL-PRF-14107 1 qt can

QT

6 C

9150-00-753-4686

LUBRICATING OIL, WEAPONS (LSA) (81349) MIL-L-46000 1 gal can

GL

7 C

7920-00-205-1711

RAG, WIPING (80244) A-A-531 50 lb bale

LB

8 C

6850-00-224-6657 6850-00-224-6663

RIFLE BORE CLEANING COMPOUND (RBC): Solution type (81349) MIL-C-372 8 oz can 1 gal can

OZ GL

9 C

1005-00-228-3565

SWAB, SMALL ARMS CLEANING (19204) 5019316 1000 pkg

EA

END OF WORK PACKAGE


TM 9-1005-338-13&P 0048 00 ALPHABETICAL INDEX WP Sequence No.

A Additional Authorized List (AAL) ........................................................................................... 0046 00 Ammunition Care and Usage................................................................................................ 0031 00 Authorized Ammunition......................................................................................................... 0009 00

C Cleaning ................................................................................................................................ 0015 00 Components of the End Item and Basic Issue Items............................................................ 0045 00 Corrosion Prevention and Control (CPC) ............................................................................. 0001 00 Cross Reference Index – National Stock Number................................................................ 0044 00 Cross Reference Index – Part Number................................................................................. 0043 00

D Destruction of Materiel to Prevent Enemy Use..................................................................... 0001 00 Differences Between Models ................................................................................................ 0002 00

E Equipment Characteristics, Capabilities, and Features........................................................ 0002 00 Equipment Data .................................................................................................................... 0002 00 Expendable and Durable Items List...................................................................................... 0047 00

F Fielding Stripping .................................................................................................................. 0014 00 Function Check ..................................................................................................................... 0017 00

H How to use this manual......................................................................................................... v

I Illustrated List of Manufactured Items................................................................................... 0030 00 Immediate Action .................................................................................................................. 0007 00

L List of Abbreviations and Acronyms ..................................................................................... 0001 00 Loading/Unloading ................................................................................................................ 0005 00 Location and Description of Major Components................................................................... 0002 00 Lubrication ............................................................................................................................ 0016 00

M Maintenance Allocation Chart (MAC) ................................................................................... 0033 00 Maintenance of (Direct Support):

Bolt Assembly (P/N 6706P)............................................................................................ 0029 00 Receiver Assembly (P/N 10171MIL and M590L) ........................................................... 0028 00

Index -1 http://www.emilitarymanuals.com

TM 9-1005-338-13&P 0048 00 ALPHABETICAL INDEX WP Sequence No.

M (cont) Maintenance of (Unit):

Barrel Assembly (P/N 3907P).........................................................................................0024 00 Barrel Assembly (P/N 41758) .........................................................................................0024 00 Fore End Assembly (P/N MOSS-05) ..............................................................................0023 00 Mossberg 12-Gauge Shotgun, Model 500 (P/N MOD500).............................................0022 00 Mossberg 12-Gauge Shotgun, Model 590 (P/N 52660) .................................................0022 00 Pistol Grip Assembly (P/N 95000) ..................................................................................0026 00 Stock, Gun, Shoulder (P/N 14762MIL) ...........................................................................0025 00

Maintenance, Forms, Records, and Reports ........................................................................0001 00

N Nuclear, Biological, an Chemical (NBC) ...............................................................................0001 00

O Operating Procedures ...........................................................................................................0005 00 Operation Under Unusual Conditions ...................................................................................0010 00 Operation Under Usual Conditions .......................................................................................0004 00 Operator’s Controls and Indicators .......................................................................................0004 00

P Preparation for Storage and Shipment..................................................................................0001 00 Preventive Maintenance Checks and Services – Operator (Introduction) ............................0012 00 Preventive Maintenance Checks and Services - Operator ...................................................0013 00 Preventive Maintenance Checks and Services – Unit Maintenance.....................................0021 00

Q Quality of Material .................................................................................................................0001 00

R References ............................................................................................................................0032 00 Remedial Action ....................................................................................................................0008 00 Repair Parts and Special Tools List (RPSTL) for:

Barrel Assembly (P/N 3907P).........................................................................................0038 00 Barrel Assembly (P/N 41758) .........................................................................................0038 00 Bolt Assembly (P/N 6706P) ............................................................................................0040 00 Fore End Assembly (P/N MOSS-05) ..............................................................................0039 00 Grip, Pistol Assembly (P/N 7995P).................................................................................0042 00 Mossberg 12-Gauge Shotgun, Model 500 (P/N MOD500).............................................0036 00 Mossberg 12-Gauge Shotgun, Model 590 (P/N 52660) .................................................0036 00 Pistol Grip Assembly (AAL) (P/N 95000) ........................................................................0042 00 Receiver Assembly (P/N 10171MIL and M590L) ...........................................................0037 00 Safety Assembly (NPN) ..................................................................................................0037 00 Stock, Gun, Shoulder (P/N 14762MIL) ...........................................................................0041 00

Repair Parts and Special Tools List (Introduction)................................................................0035 00 Reporting Equipment Improvement Recommendations (EIR)..............................................0001 00

Index -2 http://www.emilitarymanuals.com

TM 9-1005-338-13&P 0048 00

S Safety, Care and Handling.................................................................................................... 0001 00 Service Upon Receipt of Materiel ......................................................................................... 0018 00 Stoppage or Stuck Cartridge................................................................................................. 0006 00

T Theory of Operation .............................................................................................................. 0003 00 Troubleshooting Procedures, Direct Support Maintenance.................................................. 0027 00 Troubleshooting Procedures, Unit Maintenance .................................................................. 0020 00 Troubleshooting Procedures, Operator ................................................................................ 0011 00

U Unit Maintenance Instructions .............................................................................................. 0019 00

W Warning Summary ................................................................................................................ a

Index –3/4 blank http://www.emilitarymanuals.com

TM 9-1005-338-13&P 0048 00






TM 9-1005-338-13&P

DISTRIBUTION: To be furnished in accordance with the initial distribution requirements for (IDN) 401217 requirements for TM 9-1005-338-13&P.

0510101

By Order of the Secretary of the Army:

PETER J. SCHOOMAKER General, United States Army

Chief of Staff Official:

SANDRA R. RILEY Administrative Assistant to the

Secretary of the Army


TM 9-1005-338-13&P



PIN: 082431- 000


20909349-TM-9-1005-338-13-P-Mossberg-500-and-590

Documents

blank wp

title page

p http

army tm

p technical manual unit

original page

p headquarters

certain weapon