SIDExSIDE ELECTRIC FUEL/EXH LUGGAGE SECURITY TOOLS H 2 0 CONTROL ACCESS PISTONS CLUTCH CHEMICAL ENGINE WHEELS BODY SPROCKETS CHAINS BRAKES 130 ORDERS.SOUTHERNMS.COM / FAX 858-560-4626 SOUTHERN BATTERIES Refer to BRAND web- site for M.A.P. policy YTZ series • Small size, lightweight, huge power • Maintenance Free. No need to add water but periodic charging required when not in use • Absorbed Glass Mat (AGM) Separators – No need to ever add water! • Non-spillable – all acid is absorbed in special plates and AGM separators • Advanced lead-calcium technology – holds its specific gravity more than 3 times longer than conventional lead antimony batteries • Supplied “Factory Activated” (non-spillable) MAINTENANCE FREE series • Maintenance Free. No need to add water but periodic charging required when not in use • Advanced lead-calcium technology – holds its specific gravity more than 3 times longer than conventional lead antimony batteries • All acid is absorbed in special plates and AGM separators • Available as “Factory Activated” – Ready To Use – No need to handle acid! • Available as “Dry with an Acid Pack” – No need to ever add water after initial acid fill! YUMICRON CX series • YuMicron CX "lead calcium" technology - generates more power, requires less maintenance, and lasts longer than conventional batteries • YuMicron CX will generate 5% to 8% more cold cranking amperage - greater reserve capacity and more starting power • Lead calcium technology reduces water loss, so requires servicing (water filling) only about one-eighth as often as ordinary batteries • Advanced lead-calcium technology – holds its specific gravity more than 3 times longer than conventional lead antimony batteries YUMICRON series • Special thin separators – allow two extra plates per cell to be installed, for a 30% improvement in cranking performance • Sulfate stop to reduce battery sulfation • Engineered to protect against corrosion, withstand vibration, and deliver high cranking power CONVENTIONAL series - 6 & 12 VOLT • Patented separators provide high cranking power • Through-partition construction delivers maximum power • Unique sealed posts resist corrosion for longer battery life • Polypropylene cover and container thwart damage from gas, oil, and impact • Heat-sealed, bonded unit fabrication protects against seepage and corrosion HIGH PERFORMANCE - MAINTENANCE FREE series • Increased Power - up to 30% more cranking amps • Maintenance Free. No need to add water but periodic charging required when not in use • Advanced lead-calcium technology – holds its specific gravity more than 3 times longer than conventional lead antimony batteries • All acid is absorbed in special plates and AGM separators • Available as “Factory Activated” – Ready To Use – No need to handle acid! • Available as “Dry with an Acid Pack” – No need to ever add water after initial acid fill! WARNING: This product can expose you to chemicials including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov GYZ series • AGM (Absorbed Glass Mat) separators with superior grid and component designs • Improved charge recovery capability from a deeply discharged condition • Longer shelf life • Improved life cycle performance • Extreme vibration resistance • Supplied “Factory Activated” (non-spillable) • Heavy duty, flush mounted terminals. Patent pending embedded brass nut • Upgrade for customized motorcycles requiring the best performance
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
YTZ series • Small size, lightweight, huge power • Maintenance Free. No need to add water but periodic charging required when not in use • Absorbed Glass Mat (AGM) Separators – No need to ever add water! • Non-spillable – all acid is absorbed in special plates and AGM separators • Advanced lead-calcium technology – holds its specific gravity more than 3 times longer
than conventional lead antimony batteries • Supplied “Factory Activated” (non-spillable)
MAINTENANCE FREE series • Maintenance Free. No need to add water but periodic charging required when not in use • Advanced lead-calcium technology – holds its specific gravity more than 3 times longer
than conventional lead antimony batteries • All acid is absorbed in special plates and AGM separators • Available as “Factory Activated” – Ready To Use – No need to handle acid! • Available as “Dry with an Acid Pack” – No need to ever add water after initial acid fill!
YUMICRON CX series • YuMicron CX "lead calcium" technology - generates more power, requires less maintenance,
and lasts longer than conventional batteries • YuMicron CX will generate 5% to 8% more cold cranking amperage - greater reserve capacity and more starting power • Lead calcium technology reduces water loss, so requires servicing (water filling)
only about one-eighth as often as ordinary batteries • Advanced lead-calcium technology – holds its specific gravity more than 3 times longer
than conventional lead antimony batteries
YUMICRON series • Special thin separators – allow two extra plates per cell to be installed,
for a 30% improvement in cranking performance • Sulfate stop to reduce battery sulfation • Engineered to protect against corrosion, withstand vibration, and deliver high cranking power
CONVENTIONAL series - 6 & 12 VOLT • Patented separators provide high cranking power • Through-partition construction delivers maximum power • Unique sealed posts resist corrosion for longer battery life • Polypropylene cover and container thwart damage from gas, oil, and impact • Heat-sealed, bonded unit fabrication protects against seepage and corrosion
HIGH PERFORMANCE - MAINTENANCE FREE series • Increased Power - up to 30% more cranking amps • Maintenance Free. No need to add water but periodic charging required when not in use • Advanced lead-calcium technology – holds its specific gravity more than 3 times longer
than conventional lead antimony batteries • All acid is absorbed in special plates and AGM separators • Available as “Factory Activated” – Ready To Use – No need to handle acid! • Available as “Dry with an Acid Pack” – No need to ever add water after initial acid fill!
WARNING: This product can expose you to chemicials including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
GYZ series • AGM (Absorbed Glass Mat) separators with superior grid and component designs • Improved charge recovery capability from a deeply discharged condition • Longer shelf life • Improved life cycle performance • Extreme vibration resistance • Supplied “Factory Activated” (non-spillable) • Heavy duty, flush mounted terminals. Patent pending embedded brass nut • Upgrade for customized motorcycles requiring the best performance
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À MUST USE FACTORY ACTIVATED BATTERY. Á AVAILABLE AT KAWASAKI DEALERS ONLY. Â DO NOT USE GYZ BATTERY. Ã BATTERY HOLDDOWN MODIFICATIONS MAY BE REQUIRED.
À Includes 10mm spacer to replace YB14A-A1 and YB14A-A2. Ã At 20-hour rate. Á Includes terminal adaptor for conventing to top mount Ä This battery includes a sensor. Â Includes terminal adaptor for conventing to side mount Å Includes 20mm spacer if replacing YB16CL-B
À Includes 10mm spacer to replace YB14A-A1 and YB14A-A2. Ã At 20-hour rate. Á Includes terminal adaptor for conventing to top mount Ä This battery includes a sensor. Â Includes terminal adaptor for conventing to side mount Å Includes 20mm spacer if replacing YB16CL-B
YUASA BATTERY TESTERS • Developed for the powersports industry • Tests both conventional lead-acid and AGM batteries • Range: 2.3AH ~ 32AH, 12V powersports batteries • Determines battery health and charge status in seconds • Single load, dynamic resistance technology minimizes battery drain • Accurate testing on both charged & discharged batteries • Available in printer model - tester prints recommended actions DIGITAL BATTERY PRINT TESTER YUBTY01P REPLACEMENT PAPER ROLLS YUABTY01PPR (2 rolls)
JUMPER CABLES • Heavy duty, 8ft, 8-gauge cables won’t stiffen • Encased rubber grips for safer use • Tangle resistant
MS017425
149WWW.SOUTHERNMS.COM / TEL 858-560-5005SOUTHERN
SIDExSIDE
ELECTRIC
FUEL/EXH
LUGGAGE
SECURITY
TOOLS
H20
CONTROL
ACCESS
PISTONS
CLUTCH
CHEMICAL
ENGINE
WHEELS
BODY
SPROCKETS
CHAINS
BRAKES
CHARGERS/TESTERS
Refer to BRAND web-site for M.A.P. policy
2 AMP DUAL BANK CHARGER/MAINTAINER 6V & 12V 2 AMP DUAL STATION
• 2 independent charging stations • Charges 6 volt & 12 volt batteries • Automatic charging & maintenance maximizes battery life • OEM approved 5-stage charging algorithm saves time & energy • Active desulfation routine to recover sulfated batteries • Defective battery detection to eliminate surprises • Designed to prevent overcharging • Quick connect cable & alligator clamps (6 ft total length) • 5-year limited warranty 2 AMP DUAL CHARGER - 50 STATE MS017416
YUASA BATTERY TESTERS • Developed for the powersports industry • Tests both conventional lead-acid and AGM batteries • Range: 2.3AH ~ 32AH, 12V powersports batteries • Determines battery health and charge status in seconds • Single load, dynamic resistance technology minimizes battery drain • Accurate tesing on both charged & discharged batteries • Available in printer model - tester prints recommended actions DIGITAL BATTERY PRINT TESTER YUBTY01P REPLACEMENT PAPER ROLLS YUABTY01PPR (2 ROLLS)
1 AMP AUTOMATIC CHARGER & MAINTAINER 12V 1 AMP SINGLE STATION
• Fully automatic 3 level charge for effective charging • Switches to maintenance mode when battery is fully charged • 3 color LED displays your charge status at a glance • Designed to prevent overcharging; reverse polarity protection • 12 ft total cable length, quick connect adapter and alligator clamps • 5-year limited warranty 1 AMP CHARGER - 50 STATE MS017411 RING TERMINAL CABLE MS017403
YUASA CHARGER/MAINTAINER 12V 3 AMP SINGLE STATION
• Ideal for any 12V conventional, maintenance-free, AGM, SLA and gel batteries • Automatic charging & maintenance maximizes battery life • OEM approved 5-stage charging algorithm saves time & energy • Active desulfation routine to recover sulfated batteries • Defective battery detection to eliminate surprises • Designed to prevent overcharging • 13’ total cable length; quick connect cable & alligator clamps included • 5-year limited warranty 3 AMP CHARGER - 50 STATE MS017417
WARNING: This product can expose you to chemicials including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
FACTORY ACTIVATED SEALED BATTERIES (NO ACID REQUIRED)
High quality, yet competitively priced, the Power-Sonic Super Sport Series of-fers a complete line of batteries to meet all of your Powersport needs. The attractive ‘Limited Quantity’ packaging, approved by the U.S. Dept. of Transportation, not only looks great on your shelves, but saves you money by making shipping costs more effective by no longer making it necessary to pay Haz-Mat fees when transporting batteries that come with an acid pack. Built with confidence by their ISO:9001 and ISO:14001 certified factory, the broad range of sizes and battery types makes the Power-Sonic Super Sport Series one of the best choices available on the market today!
WARNING: This product can expose you to chemicials including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
SPARK PLUG CAPS • NGK Resistor Covers are designed to reduce “Electro Magnetic Interference”
and “Radio Frequency Interference” which can interfere with electronic ignition components causing misfires and poor engine performance
• Resistor Covers are manufactured using extremely durable Phenolic Resin and EPDM rubber
• Ceramic resistors are used to ensure optimum performance and reliability • Resistor Covers must withstand extreme heat, vibration, prevent flash over • NGK Spark Plugs superior design ensures optimal service life and performance
CABLE SPLICER • Connects NGK Racing Cables to ignition system • For sealed CDI system • Water resistant cable splicer • Insert cable into the splicer and tighten - done • Can save significant expense of replacing an
entire ignition system because of a failed cable
NG8083
RACING CABLES WITH RESISTOR COVER • 5K resistor cover • Protects from radio frequency interference • 90° or straight design, 20" long wire lead • High output, stranded copper wire • Increased durability & longer life • Rugged silicone insulation • Water resistant
NGK# CAP ANGLE SIZE TERMINAL RESISTANCE NOTES PART#
FLEX ERA® 3 LED LIGHTS • KC FLEX triangular design with machined accent bezel maximizes thermal efficiency and weight reduction • Spot lens optics throws a long and focused beam of light to light your way, range 607 meters
- uses 3 spot pattern LEDs • Combination lens optics spreads light like an illuminated blanket far and wide, range 385 meters
- uses 2 spread pattern LEDs and 1 spot pattern LEDs • LED source: 5000°K CREE® LED XHP 50.2 • Replaceable lens & optics • Thermal LED protection • Independent amber LED backlight • Voltage: 9v-36v • IP68 rated for water and dust • 23 year warranty for original purchaser • Included: (2) 40w KC® FLEX ERA® 3 LED lights
(2) Light covers - Black with Yellow KC logo Wiring harness and 3 position switch
FLEX ERA® 4 LED LIGHTS • KC FLEX design with machined accent bezel maximizes thermal efficiency and weight reduction • Spot lens optics throws a long and focused beam of light to light your way, range 424 meters
- uses 4 spot pattern LEDs • Combination lens optics spreads light like an illuminated blanket far and wide, range 401 meters
- uses 2 spread pattern LEDs and 2 spot pattern LEDs • LED Source: 5000°K CREE® LED XHP 50.2 • Replaceable lens & optics • Thermal LED protection • Independent amber LED backlight • Voltage: 9v-36v • IP68 rated for water and dust • 23 year warranty to original purchaser • Included: (2) 80w KC® FLEX ERA® 4 LED Lights
(2) Light covers - Black with Yellow KC logo Wiring harness and 3 position switch
LED LIGHTSGRAVITY® LED PRO6 LIGHTBAR KITS • Offroad race tested, provides the most durable, robust and scalable LED light bar design available • Easily transform the PRO6 light bar between straight or curved light orientations • Unique hinge design allows users to easily transform the PRO6 light bar between a straight and curved orientation • Powered by Gravity® Reflective Diode (GRD) technology for unparalleled beam shape, light performance and clarity • Gravity® G6 LED reflector for optical clarity and performance lens for maximum light output • Combination of Driving and Wide-40 beam pattern lights for optimal lighting balance • Driving beam lights provide powerful forward distance and equal beam distribution width • Wide-40 beam offers a wider area of coverage, increasing side to side peripheral visibility • Beam distance: 1297m (32”), 1435m (39”), 1562m (45”), 1637m (50”), 1732m (57”) • Uses 5000°K 9v-32v CREE™ LEDs • IP rating: IP68 • Vehicle kits include light bar, brackets & mounting hardware, wiring harness and waterproof switch • Universal kits include light bar, wiring harness and weatherproof switch; mounting brackets sold separately • 23 year warranty to orginal purchaser
KC091406 - 7R - 45”
KC091308 - 8R - 50”
KC091307 - 6R - 39”
KC091306 - 5R- 32”
KC091309 - POLARIS RZR 1000X 14-18
KC091308 IN FLEX CONFIGURATION
NEW
KC GRAVITY® LED PRO6 SAE/ECE DRIVING LIGHT • Includes all required hardware to
safely add an additional light to 20"-57" Gravity LED PRO6 lightbars
PART# MODEL BEAM PATTERN # OF LEDs WATTSAMPS DRAW CANDELA/ LUMENS WIDTH HEIGHT DEPTH MODEL YEAR
FLEX™ LED DUAL PAIR LIGHT KIT • Designed to link and stack vertically or horizontally to create custom array shapes and sizes • GRD LED patented technology for great visibility and clarity • Precision die-cast aluminum housing with precision polished reflector optics • Hard coated polycarbonate lens for optical clarity and maximum light output • U-bracket mounts KC FLEX™ LEDs easily in tight spaces with precise vertical and horizontal aiming of lights • Spread beam- Wider beam of light that increases peripheral lighting for an improved range of visibility, range 374 meters • Patent pending Pass Through Power Bus • Uses 5700°K 9v-18v CREE™ LEDs • IP rating: IP68 • Kit includes 2 dual Flex lights, wiring harness and weatherproof switch • 23 year warranty to orginal purchaser
‡ SPECIFICATIONS ARE PER LIGHT † RAW LUMENS @ 5000K°
C-SERIES LED LIGHTBAR KITS • Offroad race tested, designed to handle the harshest environments • Precision reflectors for great visibility and clarity • Black powder-coated extruded aluminum housings • Hard coated polycarbonate lens for optical clarity and maximum light output • GORE® membrane barrier • Combo beam with perfectly angled 8° Spot & 90° Spread reflectors, for maximum forward distance
and increased peripheral illumination, range 527m (C10), 837m (C20), 906m (C30), 1058m (C40), 1131m (C50) • Uses 6000°K 9v-32v CREE™ LEDs • IP rating: IP67 • Universal kits include light bar, wiring harness and weatherproof switch; mounting brackets sold separately • 23 year warranty to orginal purchaser
KC000334
KC000335
KC000336
KC000337
KC000338
PART# MODEL BEAM PATTERN # OF LEDs WATTSAMPS DRAW CANDELA/ LUMENS WIDTH HEIGHT DEPTH MODEL
C-2 LED BACKUP AREA FLOOD LIGHT KIT • Ideal for illuminating areas as a scene illumination, as a worklight or as an effective backup-reverse light • 120° area flood pattern for evenly distributed lighting, range 104 meters • Durable powder-coated, die-cast aluminum housing with oversized heat sink design • Optically clear and shatter proof Lexan lens for maximum light output • GORE® military grade breather membrane to prevent condensation and entry of dust/contaminants • Kit includes 2 C-2 scene lights with Z brackets, wiring harness and weatherproof switch • Uses 6000°K 9v-36v CREE™ LEDs • IP rating: IP69 • 23 year warranty to orginal purchaser
4” ROUND LZR LED PAIR LIGHT KIT • Creates a light that prioritizes distance without an overly concentrated hotspot • Precision die-cast aluminum housing with precision polished reflector optics • Hard coated polycarbonate lens for optical clarity and maximum light output • U-bracket mounts in tight spaces with precise vertical and horizontal aiming of lights • Spot beam provides focused bright light for maximum forward distance
and high speed visibility, range 283 meters • Uses 5000°K 9v-32v CREE™ LEDs • IP rating: IP68 • Kit includes 2 round LZR lights with rock covers, wiring harness and lighted switch • 23 year warranty to orginal purchaser
C-SERIES RGB LED ROCK LIGHT KIT • 6 x KC RGB LED rock light pods • Customized RGB color, light modes and functions via KC's mobile Bluetooth app available for Android or iOS • Music and Voice Sync mode: light follows the rhythm of your favorite music or voice inputs from your phone • LED speeds and sequences: Disco, Flashing, Strobe, Fade, Mono/Multi Color Jump • Brightness Control: user defined LED light intensity control • Powder-coated, die-cast aluminum housing with shatter resistant polycarbonate lens • Kit includes 6 Rock pods, 6 rubber mounting pads with hardware,
waterproof harness and Bluetooth control module • Uses 9v-36v CREE™ LEDs • IP rating: IP68 • 23 year warranty to orginal purchaser
and maximum light output • Easy attachment vis DZUS clip or M6 fastener • Ideal for fender well, track bed or underhood applications • 23 year warranty to orginal purchaser
PART# COLOR BEAM PATTERN # OF LIGHTS WATTS‡ AMPS DRAW‡ LUMENS‡ WIDTH HEIGHT DEPTH FITMENT
À INCLUDES WIRING HARNESS WITH MOUNTS & WEATHERPROOF SWITCH
‡ SPECIFICATIONS ARE PER LIGHT
GRAVITY® LED PRO-SPORT LIGHT KIT • GRD LED patented technology for great visibility and clarity • Composite PolyMax housing with machined polished reflector optics • Hard coated polycarbonate lens for optical clarity and maximum light output • Universal adjustable mounts for easy mounting and precise vertical and horizontal aiming of lights for consistency • Spot beam provides focused bright light for maximum forward distance and high speed visibility, range 972 meters • Driving beam provides added peripheral visibility while reaching further than stock lights, range 724 meters • Driving beam is DOT compliant & meets SAE J581 & ECE-R112 standards • Uses 9v-32v CREE™ LEDs • IP rating: IP68 • Kit includes 2 lights with rock covers, wiring harness and weatherproof switch • 23 year warranty to orginal purchaser
APOLLO PRO 100W HALOGEN DUAL LIGHT KIT • Created for the most demanding off-road terrains, engineered to last and perform for years to come • Slim black composite PolyMax housing with computer designed polished reflector optics • Durable optical quality glass lens for clarity and maximum light output • Universal adjustable mounts for easy mounting and precise vertical and horizontal aiming of lights • Spot beam - focused light for maximum forward distance & high speed visibility, range 886 meters • Spread beam - balanced wider beam increases peripheral visibility, range 693 meters • Uses 9v-32v H3 bulb • IP rating: IP67 • Kit includes 2 lights with rock covers,
relay wiring harness and weatherproof switch • 23 year warranty to orginal purchaser
6” DAYLIGHTER® 100W HALOGEN DUAL LIGHT KIT • Strong and durable light that will withstand the most severe conditions • Spot beam provides focused bright light for maximum forward distance & high speed visibility,
range 1058 meters • Black steel shock mounted housing with polished reflector optics • Daylighter shock mount system is resilient and ensures beam stability • Tempered durable glass lens • Kit includes 2 lights with light covers, wiring harness and weatherproof switch • Uses 9v-32v H3 bulb • 23 year warranty to orginal purchaser
PART# MODEL BEAM PATTERN FINISH WATTS‡ AMPS DRAW‡ CANDELA/ LUMENS‡ WIDTH HEIGHT DEPTH MODELKC009150 9150 SPOT BLACK 100W 8.30 196,200/2,452 6.00" 6.75" 3.50" UNIVERSAL KITKC000151 151 SPREAD BLACK 100W 8.30 120,000/2,452 6.00" 6.75" 3.50" UNIVERSAL KIT‡ SPECIFICATIONS ARE PER LIGHT
PART# MODEL BEAM PATTERN FINISH WATTS‡ AMPS DRAW‡ CANDELA/ LUMENS‡ WIDTH HEIGHT DEPTH MODELKC000238 238 SPOT BLACK 100W 8.30 279,585/2,452 6.19" 8.42" 5.34" UNIVERSAL KIT‡ SPECIFICATIONS ARE PER LIGHT
GRAVITY® LED 7” HEADLIGHTS • GRD LED patented technology for great visibility and clarity • Built-in Day Running Light capability for DRL enabled vehicles • Precision die-cast aluminum housing with machined polished reflector optics • Hard coated Polycarbonate lens for optical clarity and maximum light output • Easy Plug-n-Play installation • Fully DOT compliant high/low beams with anti-flicker capacitors • Uses 5000°K CREE™ LEDs • IP rating: IP68 • 23 year warranty to orginal purchaser
PART# BEAM PATTERN# OF LIGHTS
WATTS‡ LOW/HIGH BEAM
AMPS DRAW‡ Candela/ Lumens‡ Width Height Depth Make Model Year
GRAVITY LED PRO 7" HEADLIGHTSKC042341 DRIVING 2 18W/25W 1.88 40,000/70,000 7.00” 7.00” 5.09” JEEP WRANGLER JKÀ 07-18‡ SPECIFICATIONS ARE PER LIGHTÀ EXCLUDES WRANGLER JK FITTED WITH FACTORY OEM LED HEADLIGHTS, 17-18 WRANGLER JK RUBICON OR SAHARA EDITIONS
UNIVERSAL TUBE CLAMP MOUNTING BRACKETS • 2-Piece black tube clamp mounting brackets • Strong glass-injected nylon composite material • Rubber adjustment shims for easy and accurate fitment • Available in different sizes, fits 0.75" to 3" diameter round tubing • Made in USA • 23 year warranty to orginal purchaser
KC072011 BLACK COVER Fits 10" C-Series - order 2x for 20" lightbar, etc..KC072021 AMBER COVER Fits 10" C-Series - order 2x for 20" lightbar, etc..
MOUNTING BRACKETS
LIGHT COVERS
VEHICLE SPECIFIC MOUNTING BRACKETS • Bolts to factory holes (No drilling required) • Durable black powder-coated finish • Designed in USA • 23 year warranty to orginal purchaser
BRAND MODEL YEARS DESCRIPTION PART#
JEEP WRANGLER JK 07-18 Windshield hinge brackets - pair KC007316
low beam, high beam; turn signal switch; horn or kill
• Fits 7/8” handlebar • Overall wire length 24”
including 8” extension wire KS120055CN
HANDLEBAR SWITCH • One function switch • For 7/8” handlebars MS120201
HANDLEBAR SWITCH • Headlight on/off, low beam & high beam • Blue LED light indicates when high beam is on • Turn signal switch • Horn or kill function • Fits 7/8” handlebar
TACH/HOUR METER • Tracks RPM and hours used • Easy installation • Meter mount available HLHR8061
RESETTABLE HOUR METER • 3 resettable service alarms • Resettable time mode • No power or ground wires • Total time accumulated mode METER HLHR8067 METER MOUNT HLHRMM2
K&S NEUTRAL SWITCH • Based on OEM replacement switch
PART# DESCRIPTION OEM#IMAGE
#
KS120070 HONDA 35600-HA0-00 1
KS120072 HONDA 35600-452-003 2
KS120073 YAMAHA 3GB-82540-01 3
PART# DESCRIPTIONIMAGE
#
KS240001 FLASHER RELAY 12V, 2PRONG, 21-23W 1
KS240002 FLASHER RELAY 12V, 3PRONG, 21-23W 2
KS240005 FLASHER RELAY DOT APPROVED, IC TYPE, MAXIMUM LOAD 15 AMPS 3
LICENSE PLATE BOLT LIGHTS • Used to replace OEM license plate light • Bolts on easily to hold the license plate • Bright white LED lights • Sold in pairs BLACK FINISH KS259160B SILVER FINISH KS259160
LIGHTED HANDLEBAR ENDS • Bar end with amber integrated light • Sold in pairs BLACK FINISH KS151010 SILVER FINISH KS151000
LED MARKER LIGHT • 15 LED’s • Flexible stem • Bolts on easily • Sold in pairs BLACK FINISH KS259300
LED LICENSE PLATE LIGHT • 3 White 12v LED’s • DOT approved • Bolts on easily BLACK FINISH KS259170
UNIVERSAL LED TURN SIGNALS • Very bright single unit LED, 12v 1.1 watts • Fully sealed and waterproof • Lens is specially designed for most effective light
transmission to meet DOT requirements BLACK FINISH AMBER LENS KS259563 BLACK FINISH CLEAR LENS KS259561 BLACK FINISH SMOKE LENS KS259562
LED LICENSE PLATE LIGHT • 5 White 12v LED’s • DOT legal • Bolts on easily
KS259154
DOT APPROVED LED TURN SIGNALS • Turn signals meet or exceed all government requirements
for light output and durability • Legal for all street or dual-purpose motorcycles ON ROAD / OFF ROAD AMBER LENS KS257000 DOT MINI-STALK AMBER LENS KS257500 DOT KTM STYLE AMBER LENS KS257600