Search You are here: Home page>Tools, instruments, and measurement>Strain gauges • Home • A-Z index • Get the book• Follow us • Random article • Timeline • Teaching guide • About us • Privacy policy Advertisement How strain gauges work • • 0 • Tweet Esta pág exibida Página 1 de 11 How stra in gauges work - Explain t hat Stuff08/03/2016 http://www.explainthatstuff.com/straingauge.html
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
IIs your house in danger of falling down? Was that an earthquake? Will that airplane actually fly?These are just a few of the questions you can study with a handy little device called a strain gauge
(sometimes spelled "gage"). It's a neat way of measuring how much a material changes shape
when a force acts on it. Strain gauges range from the immensely simple to the fiendishly complex, but all of them are superbly useful to scientists and engineers. Let's take a closer look at how they
work!
Photo: This laboratory apparatus is designed to test a material's strength by slowly pulling it apart.
Strain gauges attached to the material (in this case, a piece of aluminum in the center) let scientists
study the stresses and strains as it deforms. Photo by courtesy of NASA Langley Research Center
(NASA-LaRC).
What is strain anyway?
Are you stressed? Can you feel the strain? When we talk about "stress" and "strain" in everydaylife, we use the two words interchangeably. But in science and engineering, these two words have
very precise and very different meanings:
• Stress is a measurement of how much internal pressure a material is under when a force acts
on it. The bigger the force or the smaller the area over which it acts, the more likely it is that
the material is to going to deform (change shape). Just like pressure, we measure stress by
dividing the force that's acting by the area it's acting over, so stress = force / area.
• Strain is what happens as a result of stress. If a material is stressed by a force, it often
changes shape and gets a little bit longer (if you've pulled it apart) or shorter (if you've
pushed it together). The strain is defined as the change in length the force produces divided
by the material's original length. So if you pull a 10cm-long piece of elastic and it stretches by 1cm, the strain is 0.1.
Página 2 de 11How strain gauges work - Explain that Stuff
Artwork: The concepts of stress and strain compared. Top: Stress: If you apply a pulling force to a
bar of a certain cross-sectional area, you create a certain stress. If you apply the same force to a
bar half the area, you produce twice as much stress. Bottom: Strain: If you apply no force to a bar,you don't stretch it at all. Apply a certain force and you'll extend its length by a certain amount,
producing a certain strain. If you apply more force so you double the extension, you'll have produced twice as much strain.
Materials under stress
Different materials behave in very different ways under similar amounts of stress. If you subject arubber band to stress, by pulling, it stretches accordingly; release the stress and the band returns to
its previous shape. When materials go back to their original shape and size after stressing forces
are removed, we say they've undergone elastic deformation; many materials behave like this,
including rubber, some plastics, and many metals (which, you might be surprised to hear, are
perfectly elastic when very small forces are involved). Eventually, elastic materials reach a point
where they can't cope with extra stress and stretch permanently. This kind of change is called
plastic deformation. (Note that the proper meaning of plastic is something that changes shape
relatively easily. That's why plastics are called plastics: they are easily molded into different
shapes when they are manufactured.)
If you're an engineer, stresses and strains are incredibly important. If you're designing anything
from a car engine or a bridge to a wind turbine or an airplane wing, you know it's going to be
subject to some pretty hefty forces. Can the materials you want to use stand up to those forces?
Will they deform elastically by tiny amounts and return safely to their original shape and size?
Will they break apart after repeated stresses and strains through a process such as metal fatigue
(where repeated deformation causes a metal to weaken and suddenly snap). Do you need to use
something stronger to be on the safe side? And how exactly can you tell? You can do your
calculations in the lab and try to figure it out in advance. You can even build sophisticatedcomputer models to help you. But the sure-fire way of getting an answer to how materials are
coping under pressure is to use strain gauges to measure the way they behave when real-life forcesact on them.
Página 3 de 11How strain gauges work - Explain that Stuff
Photo: NASA is using strain gauges here to measure what's happening on the inside of an airplane
wing. Photo by courtesy of NASA Dryden Flight Research Center (NASA-DFRC).
Types of strain gauges
There are five main types of strain gauges: mechanical, hydraulic, electrical resistance, optical,
and piezoelectric. Let's compare how they work.
Mechanical
Suppose you have a crack forming in a wall of your home because of subsidence and you want to
know if it's getting any worse. Call in the building inspectors and they'll probably glue a piece oftough, plexiglass plastic, ruled with lines and a scale, directly over the crack. Sometimes known as
a crack monitor, you'll find it's actually made up of two separate plastic layers. The bottom layer
has a ruled scale on it and the top layer has a red arrow or pointer. You glue one layer to one sideof the crack and one layer to the other so, as the crack opens, the layers slide very slowly past one
another and you can see the pointer moving over the scale. Depending on how quickly the crack is
moving, you know how long you have to take action and resolve your problem!
Photo: A simple mechanical crack monitor. You watch the red crosshairs move on the scale as the
crack widens. Detectors like this are made by such companies as Avongard.
Some mechanical strain gauges are even more crude than this. You simply glue the piece of
plastic or glass across your crack and wait for it to shatter when the building moves.
Hydraulic
One of the problems with strain gauges is detecting very small strains. You can imagine, for
example, a situation where your house is slowly subsiding but the amount of movement is sosmall that it won't show up—perhaps until the damage is done. With a simple crack detector such
as the ones described above, it takes 1mm of building movement to produce 1mm of movement onthe surface of the crack detector. But what if we want to detect movements smaller than this that
don't show up on a scale? In this case, what we really need is a strain gauge with leverage that
amplifies the strain, so even a tiny movement of the detecting element produces a very large and
easily measurable movement of a pointer over a scale.
Página 4 de 11How strain gauges work - Explain that Stuff
Hydraulic detectors offer a solution and work much like simple syringes. Syringes are essentially
hydraulic pistons where a small movement of fluid in a large piston (the part you press with yourfinger) produces a much larger movement of fluid in a small piston attached to it (the needle
where the fluid comes out). It's easy to see how this can be used in a strain gauge: you simply
connect your large piston to whatever it is that's producing the strain and use a smaller piston in a
smaller tube, marked with a scale, to indicate how much movement has occurred. The relative sizeof the pistons determines how much the movement you're trying to detect is scaled up. Typically,
hydraulic strain gauges like this multiply movement by a factor of 10 or so and are commonly
used in geology and Earth science.
Artwork: A simple example of a hydraulic strain gauge. The strain you want to measure presses
down on the green button (top left). That forces a large, wide piston (yellow, 55) into a hydraulic
cylinder (red, 56), squashing trapped fluid (blue) down through a narrow pipe. This is the
hydraulic principle in action: tiny movements of the green button and yellow piston are magnified
into much larger movements by the narrowness of the tube. The fluid flows into a coiled-up
Bourdon tube (orange, 83), which uncurls according to the pressure inside it, pulling on a lever
linkage (dark blue, 84, 85), altering the overlap between a couple of induction coils so they sendmore or less electric current to a circuit. In this way, a force pressing on the green button is
translated into a measureable electric signal. From US Patent 2,600,453: Method and apparatus for
controlling heat in hot machining processes by Richard Weingart. June 17, 1952, courtesy of US
Patent and Trademark Office.
Electrical resistance
If you're designing something like an airplane wing, typically you need to make far more
sophisticated measurements (and many more of them) than a simple mechanical strain gauge will
allow. You might want to measure the strain during takeoff, for example, when the engines are
producing maximum thrust. You can't go sticking little plastic strain gauges onto the wing andwalk out to measure them during a flight! But you can use electrical strain gauges to do much the
same thing from a flight recorder in the cockpit.
Página 5 de 11How strain gauges work - Explain that Stuff
The most common electrical strain gauges are thin, rectangular-shaped strips of foil with maze-
like wiring patterns on them leading to a couple of electrical cables. You stick the foil onto the
material you want to measure and wire the cables up to your computer or monitoring circuit.
When the material you're studying is strained, the foil strip is very slightly bent out of shape and
the maze-like wires are either pulled apart (so their wires are stretched slightly thinner) or pushed
together (so the wires are pushed together and become slightly thicker). Changing the width of a
metal wire changes its electrical resistance, because it's harder for electrons to carry electric
currents down narrower wires. So all you have to do is measure the resistance (typically using a
Wheatstone bridge) and, with a bit of appropriate conversion, you can calculate the strain. If theforces involved are small, the deformation is elastic and the strain gauge eventually returns to its
original shape—so you can keep making measurements over a period of time, such as during the
test flight of a prototype plane.
Resistance-type strain gauges like this were invented in 1938 by MIT professor Arthur Ruge
(1905–2000) to help with earthquake detection.
Photo: Left: A closeup of two electrical strain gauges. You can clearly see the maze-like wiring patterns on the foil backing. These change shape, causing the wires to change resistance when the
foil is bent by stresses and strains. Photo by courtesy of NASA Glenn Research Center (NASA-
GRC) .
Página 6 de 11How strain gauges work - Explain that Stuff
Artwork: Right: An illustration of Arthur Ruge's original electrical resistance strain gauge from a
US patent he filed in September 1939. It consists of a conducting metal filament (yellow)
stretched back and forth between a pair of comb-like supports (blue) and connected to contacts(red) that can be wired into a circuit. As the strain changes, the filament is distorted and its
resistance rises or falls; measuring the resistance is a way of indirectly measuring the strain. Thegauge includes a second, similar filament (orange) that can be used to compensate for any changes
in resistance caused purely by changes in temperature. The idea is to choose different materials forthe two filaments so that their temperature changes cancel one another out. Ruge made his
filaments from strain-sensitive alloys such as Advance (copper-nickel) and Nichrome (nickel-
chrome). From US Patent 2,350,972: Strain gauge by Arthur C. Ruge, June 6, 1944, courtesy of
US Patent and Trademark Office.
Optical
Some materials change their optical properties (how they transmit or reflect light) when they're
stressed and strained— glass and plastics are good examples. Although glass is an amazingly
useful and versatile material, it's fragile and brittle, and potentially very dangerous: if it's under too
great a strain, it can suddenly crack or shatter without warning. That could be a real problem insomething like a plate-glass storefront window or a car windshield. One way to detect strain in
glass is to shine polarized light onto it at an angle. Some of the light will be reflected and somewill be transmitted; the relative amounts of transmitted and reflected light will change according
to how much strain the glass is under. By measuring the amount of reflected light, we can
precisely measure the strain on the glass.
Artwork: An optical strain gauge seen from the side (top) and from above (bottom), works in a
similar way to a device called a polariscope (or polarimeter). It's made from two hollow tubes
(gray 1,2) arranged at an angle to a piece of glass (green). A powerful light (blue, 6) shines a
focused beam (yellow) down onto the glass through a polarizing filter (red, 8). According to
whether the glass is strained, and by how much, some light reflects back up off the glass surfacethrough a second filter (orange, 9) and onto a photoelectric cell (purple, 14). This converts the
light into an electrical signal, making a needle rise or fall in an ammeter (dark blue, 15). Thegreater the strain on the glass, the more light is reflected and the higher the reading on the
Página 7 de 11How strain gauges work - Explain that Stuff
ammeter. From US Patent 2,119,577: Strain gauge for and method of measuring strains in glass by
Samuel McK. Gray, June 7, 1938, courtesy of US Patent and Trademark Office.
Piezoelectric
Some types of materials, including quartz crystals and various types of ceramics, are effectively"natural" strain gauges. If you push and pull them, they generate tiny electrical voltages between
their opposite faces. This phenomenon is called piezoelectricity (pronounced pee-ayyyy-zoelectricity) and it's probably best known as a way of generating the timekeeping signal in quartz
watches. Measure the voltage from a piezoelectric sensor and you can calculate the strain very
simply. Piezoelectric strain gauges are among the most sensitive (about 1000 times more so than
simpler types) and reliable and can withstand years of repeated use. (You'll sometimes see them
called piezoelectric transducers, because they convert mechanical energy into electrical energy.)
Photo: How a piezoelectric strain gauge works. Fasten it to the object you're testing, which might
be a simple steel bar (gray, 1). The sensor is a flat crystal (blue, 3), with two parallel faces that
have electrodes fixed to them (colored red and orange, 4 and 5) attached to contacts (yellow, 6 and7) that run out to an external circuit and some kind of meter. The lower face of the crystal (red) is
bonded with cement (8) very firmly to the test sample. As the sample deforms, the crystal deformstoo, generating a small voltage between its top and bottom faces as its shape changes. The bigger
the strain, the bigger the voltage, so measuring the voltage is a very accurate way of measuring the
strain. From US Patent 2,558,563: Piezoelectric strain gauge by William Janssen, GeneralElectric, June 26, 1951, courtesy of US Patent and Trademark Office.
•
• 0
• Tweet
Further Reading
On this website
• Alloys• Buildings
Página 8 de 11How strain gauges work - Explain that Stuff
• Strain Measurements and Stress Analysis by Akhtar S. Khan and Xinwei Wang. Prentice
Hall, 2001.
• Strain Gauge Technology by A. L. Window. Springer, 1992.
• Strain Gage Users' Handbook by Richard L. Hannah and Stuart E. Reed. Springer, 1992.
Materials engineering
• Harris' Shock and Vibration Handbook by Allan G. Piersol and Thomas L Paez. McGraw-
Hill, 2009. Covers the scientific theory of shocks and vibrations and the practical matter of
measuring and controlling them. Includes some history of strain gauges in Chapter 12"Strain gage instrumentation."
• The Science and Engineering of Materials by Donald R. Askeland et al. Cengage Learning,2010. A general textbook covering materials science.
• Mechanics of Materials by James Gere and Barry Goodno. Cengage Learning, 2008. A
clearly illustrated textbook covering all the basic, practical concepts of materials and theiruse in engineering.
General introductions
• The New Science of Strong Materials by J.E. Gordon. Princeton University Press, 2006.
(Available in numerous earlier editions.) A classic, very readable introduction to the scienceof the materials that surround us. See particularly "Chapter 2. Stresses and Strains."
• Stuff Matters by Mark Miodownik. A friendly introduction to everyday materials aimed at
general readers. Each chapter is devoted to a different material.
Sponsored links
Esta págin
exibida
• Verifique se o endereço d
Página 9 de 11How strain gauges work - Explain that Stuff