2015 Product Line - Industrial Controls · • Improved control sequences, protections and other tweaks! ... • Improved limits and safety interlocks . M2000 BLR Boiler Controller

5

2015 Product Line

Table of content • VC2000 Controller

• Main features • Actuators, flow sensor • LED lights • Room sensors • Analog input (AI) • Addressing • Wiring • Comparison VC1000 -vs- VC2000

• M2000 Controller • Main features • Improved RTU sequence • M2000 MUA, sequence and operation • M2000 BLR, sequence and operation

• C1000 Controller • Main features • Various models

• T1100 stand alone thermostat • Main features

• Communicating Wall Sensors • Main features • Wiring

• NC2000 Network Controller • Main features

PL-VC2000

• Small footprint, installs everywhere • New integrated HALOMO® actuators • Two fully configurable outputs • Quick & easy installation and setup • Available with ``P.I.´´ flow sensor • Modbus or BACnet communication • 3x new wall sensors available • Fully compatible with existing Prolon gear

VC2000 VAV controller

New actuators / Air flow sensor

• The VC2000 uses brand new Belimo Halomo ® technology actuators • Standard torque (45 in-lbs) • High torque (90 in-lbs)

• Both models are also available as pressure independent with the optional air flow sensor

PL-VC2000 PL-VC2010-PI


LED lights

The VC2000 uses bright, multicolored easy to read indication lights. Easy to see in a dark, crowded plenum! Each function has its unique LED No cover to open! Startup and troubleshooting procedures are facilitated

RS-485 NET Transm. (Red) RS-485 NET Rec. (Green)

RS-485 INT Transm. (Red) RS-485 INT Rec. (Green)

Processor / HBEAT. (Blue)

24Vac Supply (Blue)

Status (Yellow)

Analog Output (Orange)

Digital Output (Red)


ProLon new wall sensors • The VC2000 is designed to operate with any

of the communicating wall sensors

• LVT #18/4 or CAT5e / RJ-45* cabling

• Full digital display PL-T1000 sensor with access to configuration parameters for service. Input for remote temp. sensor

• Digital PL-T500 sensor with setpoint / room temperature display

• Electronic PL-T200 sensor with set point adjuster only

*On sensor side only

PL-T1000

PL-T500

PL-T200


VC2000

INT A

INT B

24 VAC

COM COM

24 VAC

INT B

INT A12

11

10

9

1

2

3

4

Analog Input (AI)

Multi purpose input allows many sequences:

• Supply air temp.* • Room temp (no local set point) • Discharge air temp. • Slab temp. (radiant heating) • Occupancy (contact input)

Input type is jumper configurable inside the controller, for other signal types(0-5Vdc, 4@20mA)

AICOM 13

14

Sonde de gaine (PL-CODS)

10 K type 3

JP40-5 volts4-20 mATHERMISTANCE

OU CONTACT SEC

JP4

(défaut)

Typical use as a supply air sensor for automatic changeover (when stand alone) *Default mode


Virtual Addressing

Network addressing of the VC2000 is now done virtually, without switches. It can either be configured with the help of the Focus software or with any of the digital display wall sensors (T1000, T500)

Quick and easy addressing procedure using the Prolon Focus v.5.5.0 software

When ``Status’’ is on, no valid address is present in controller


Wiring

End of line terminating resistor

Network comm. bus (toward unit controller) AI input Interface comm. bus + 24Vac supply for communicating wall sensor

Analog 0-10V output for heat / cool, etc. Digital output, dry contact -or- 24Vac for terminal heating, cooling, etc. 24Vac power supply

New removable and numbered terminal blocks


PL-VC2000 PL-VC1000

• Unique platform incorporating 2x outputs (DO + AO) eq: VC1000LT+LMZS • New, more powerful HALOMO® actuators (45 & 90 -vs- 35 in-lbs) • Available with new, wide range pressure independent air flow sensor • Internal switches and jumpers eliminated (no cover to open!) • Easy diagnostic and troubleshooting with multicolor LED’s • New communicating wall sensor series (T1000, T500, T200) -vs- passive PL-RS • Very compact and easy to install (1/2 footprint of the VC1000) • Fully network compatible with other / existing VC1000 controllers • Focus software graphic interface is identical as VC1000

VC2000 -vs- VC1000

M2000 Unit Controller

New M2000 unit controller!

• New, larger universal platform • Multicolor LED’s for display • Comm. jumpers accessible from top • RS485 INT port is quadrupled! • Improved M2000 RTU roof-top model • 3x Brand new releases:

• M2000 MUA (Make-up Air) • M2000 BLR (Advanced Boiler) • M2000 HPS (Stand-Alone heat-pump)

Terminating and Bias resistors for the ``Interface´´ and ``Network´´ ports are now easily accessible from top of controller

The Interface comm. port has a dual RJ-45 socket connection but also two new screw type terminals to allow wiring with shielded, two wire pair cable as well as CAT5e

M2000 Unit Controller

M2000 RTU Roof-top Controller

M2000 RTU

(Advanced Roof Top) • New, and improved economizer

sequences

• Combined temperature and humidity

display

• New centralized dehumidification

sequence

• Improved control sequences, protections

and other tweaks!


M2000 RTU

Advanced economizer sequences • Actuator positioning based on cooling demand

(standard sequence)

• Actuator positioning based on outdoor temp reset

supply air set point.

• Controlled by either mixed or supply air sensor

location


Combined temperature and humidity display • As soon as a Prolon humidity controller is

networked with the M2000, both temperature and

humidity data are exchanged between them.

• The humidity controller adds return air

temperature info on its display along the return air

humidity reading. Likewise for the supply sensor.

• The M2000 unit controller does the same by

adding humidity reading to its’ corresponding

temperature sensors.


Centralized dehumidification sequence • Independent contact output from the Prolon humidity

controller (roof tops with built-in dehum. coil)

• Simultaneous cooling and re-heating from the RTU

controller .

• VAV zone terminal boxes automatically open to allow

most efficient ventilation.


M2000 MUA Make-up unit Controller

M2000 MUA

(Make Up Air Unit) • Many seasonal control sequences

• Free + mechanical cooling sequences

possible

• Highly advanced limits and safeguards

• Alarm sequence with override

• Fixed or variable air flow (VFD)

• Building static pressure control

• Outdoor and ambiant temperature reset

strategies

M2000 MUA


M2000 MUA (Make Up Air Unit) • Multiple seasonal control strategies / Free + mechanical cooling

• Exhaust fan / Manual Interlock strategy / Alarm with reset

• Fixed or variable air volume / Ambiant temperature supply set point reset


Basic unit configuration • Fixed supply set point or zone temp

reset • Single air volume with fixed exhaust

rate • Dual air volume with two stage

exhaust strategy • Variable air volume for building

pressurization or indoor air quality control (Co2)

Winter control sequence • Outdoor temperature interlock

(heating) • Supply air set point reset by outdoor //

ambiant temperature • Fully integrated heating and cooling

demand reset band

Summer control sequence • Designed for mechanical cooling units

in mind • Outdoor temperature interlock

(cooling) • Cooling management by outdoor or

ambiant temperature conditions


M2000 BLR Boiler Controller

M2000 BLR

(Advanced Boiler) • New advanced boiler controller

• Controls up to 4x boilers

• Controls 2x pumps + modulating 3-way valve

• Lead-Lag & equal run time strategies on boilers

and pumps

• Dual reset control strategies

• Improved limits and safety interlocks


M2000 BLR

Pump control • Runs single or two pumps • Outdoor temp and heating demand

interlock conditions • Lead-lag / backup pump sequence • Equal run time and pump exercise

sequences

Boiler control • 4x configurable DO’s:

Single 4x stage boiler Two dual stage boilers Four single stage boilers

• 1x Modulating 3-way valve • Outdoor temp and heating demand

interlock conditions • Lead-Lag / equal run time strategy

Temperature control • Fixed or outdoor temperature reset set

point • Additional reset by heating demand /

occupancy • Return temp limitation • Morning warmup start up sequence


ProLon C1000

• C1000 VAV Zone controller (actuator-less) • C1000 HU Humidity controller • C1000 RTU Basic roof-top Master controller • C1000 HP Basic heat-pump Master controller • C1000 BLR Basic boiler controller • C1000 HPS Stand alone heat-pump controller • C1000 WLC Water loop controller • And more to come…!

C1000 Controllers

C1000 Controllers

C1000 VAV • Standard or pressure-independent operation • Controls remote floating or 0-10vdc mod. actuator • 5x fully configurable outputs (4xDO’s, 1x AO) • Great for other simple heat / cool applications • Uses analog PL-RS wall sensor + any

communicating sensors (T200, T500, T1000)

C1000 Controllers

C1000 HU • Humidification and dehumidification sequences • On-off and modulating humidification • Optional progressive supply high limit • Shares outdoor sensor / proof-of fan with Master • Outside air temperature set point reset • Stand alone or centralized dehumidification

C1000 Controllers

C1000 RTU • Master controller for VAV zones • Basic 2x heat/ 2x cool + fan sequence • Ideal for Constant Volume RTUs • Same performance & features as M2000 RTU

C1000 HP • Master controller for VAV zones • Basic 3x heat/ 2x cool + fan sequence • Ideal for Constant Volume RTUs • Same performance & features as M2000 HP

C1000 Controllers

C1000 BLR • Basic entry-level boiler controller • Single pump / 2x stage single boiler design • Can control modulating 3-way mix. Valve • Outdoor air reset strategy • Zone demand reset strategy • Can work stand alone or networked • Same performance as advanced M2000 BLR

C1000 Controllers

C1000 WLC • Closed water loop controller temperature controller • Controls a cooling tower + boiler together • Boiler acknowledgement contact • Cooling tower with or without a bypass valve • Controls tower spray pump, dampers and fan speed • Can work stand alone or networked • Ideal for multiple water sourced heat pump buildings

C1000 Controllers

C1000 HPS • Stand alone heat pump controller / single thermostat operation – no zones! • Air/air or Water/air condenser design • Ideally suited for large projects with multiple units and single water loop • Visualization is simplified by grouping multiple units on a single navigation page • Works with communicating wall sensors (T200, T500, T1000)

Stand alone, fully configurable heating / cooling thermostat

• Has two configurable outputs (1x AO + 1x DO)

• Multi-function AI sensor input: (Remote, Average, Slab temp.)

• Perfect for CV zones or terminal heating equipment

• Keypad access to all configuration parameters

• Can be networked for additional control strategies (occupancy scheduling, outdoor temp. lock out, etc.)

PL-T1100

T1100 Thermostat

NC2000 Network Controller

New NC2000 Network Controller! • Available now! • New universal platform (M2000) • Comm. jumpers available on top • RS485 input & output ports • More powerful processor, improved

communication performance • Interface comm. Port on both RJ-45 and

screw type terminals • More to come!

Prolon Focus App!

New Mobile Focus App!

• Available now! • Designed for Androïd v.4.0 tablets and

phones • Allows Wi-Fi, internet or hard wired

(USB) access to any Prolon system • Works on all screen sizes • User friendly navigation • Free to download!

And more is on the way!

2015 Product Line - Industrial Controls · • Improved control sequences, protections and other tweaks! ... • Improved limits and safety interlocks . M2000 BLR Boiler Controller

Documents