1-1 Melters Adhesives and Sealants Guide Part 1101879A ProBlue ® 4, ProBlue 7 and ProBlue 10 Adhesive Melters Description Nordson ProBlue melters are simple and compact, designed to maximize uptime and reduce operating costs. These rugged, flexible, non-handed melters fit on virtually any packaging line. S Large tank opening with three sided access allows easier filling and cleaner operation. S Status-at-a-glance indicators highlight: ready, fault, service and temperature status for tank, hose and applicator. S Simplified intuitive controls and service indicators require less user training and simplify maintenance scheduling. S Disposable filter reduces daily maintenance by eliminating routine filter flushing. S Standard tank low-level indicator and output protects against operator oversight and helps assure continuous production. S Standard programmable I/Os (3 output and 4 input) facilitate parent machine integration. S Remote temperature setback, hose/applicator enable/disable, and automatic temperature setback are standard programmable features to enhance operation. S All major components are easily accessible from the front of the melter, and all major subsystems are easily replaced. S Quick-disconnect primary power and I/O plugs and pneumatic fittings provide easier installation. S Communications options and serial and network communications allow improved integration into parent machine control systems. S Cast-in heating elements and Teflon R -coated tanks provide fast warm-up time, improve heat transfer and reduce char buildup. S Easy-to-remove exterior panels are constructed of rugged sheet molded FRP and include a heavy duty tank lid. S Sub-base allows easy, quick access to mounting bolts and electrical knockouts for easier installation.
64
Embed
2010 A&S print - SIGMA Equipment · 2016. 5. 7. · Melters 1-3 Part 1101879A Adhesives and Sealants Guide ProBlue® 4, ProBlue 7 and ProBlue 10 Adhesive Melters (contd) Specifications
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1-1Melters
Adhesives and Sealants GuidePart 1101879A
ProBlue® 4, ProBlue 7 and ProBlue 10 Adhesive Melters
Description Nordson ProBlue melters are simple and compact,designed to maximize uptime and reduce operatingcosts. These rugged, flexible, non-handed meltersfit on virtually any packaging line.
� Large tank opening with three sided access allowseasier filling and cleaner operation.
� Status-at-a-glance indicators highlight:ready, fault, service and temperature status for tank,hose and applicator.
� Simplified intuitive controls and service indicatorsrequire less user training and simplify maintenancescheduling.
� Standard tank low-level indicator and output protectsagainst operator oversight and helps assurecontinuous production.
� Standard programmable I/Os (3 output and 4 input)facilitate parent machine integration.
� Remote temperature setback, hose/applicatorenable/disable, and automatic temperature setbackare standard programmable features to enhanceoperation.
� All major components are easily accessible from thefront of the melter, and all major subsystems areeasily replaced.
� Quick-disconnect primary power and I/O plugs andpneumatic fittings provide easier installation.
� Communications options and serial and networkcommunications allow improved integration intoparent machine control systems.
� Cast-in heating elements and Teflon�-coated tanksprovide fast warm-up time, improve heat transfer andreduce char buildup.
� Easy-to-remove exterior panels are constructed ofrugged sheet molded FRP and include a heavy dutytank lid.
� Sub-base allows easy, quick access to mountingbolts and electrical knockouts for easier installation.
1-2 Melters
Adhesives and Sealants GuidePart 1101879A
ProBlue® 4, ProBlue 7 and ProBlue 10 Adhesive Melters (contd)
ProBlue Melter 200−240 VAC and 400/230 VAC with Standard 14:1 PumpParameter ProBlue 4 ProBlue 7 ProBlue 10
2 Hose/Applicator 1022230 1022232 1022234
4 Hose/Applicator 1022231 1022233 1022235
6 Hose/Applicator — — 1022236
ProBlue Melter 200−240 VAC and 400/230 VAC with 6:1 PumpParameter ProBlue 4 ProBlue 7 ProBlue 10
2 Hose/Applicator 1080419 1089193 1089195
4 Hose/Applicator 1089192 1089194 1089196
ProBlue Melter 400 and 480 VAC with Standard 14:1 Pump Parameter ProBlue 4 ProBlue 7 ProBlue 10
2 Hose/Applicator 1022237 1022238 1022240
4 Hose/Applicator 1090495 1022239 1022241
ProBlue Melter 400 and 480 VAC with 6:1 Pump Parameter ProBlue 4 ProBlue 7 ProBlue 10
2 Hose/Applicator 1078280 1078258 1078281
4 Hose/Applicator 1090496 1078259 1080440
NOTE: 400 and 480 VAC melters must have a transformer base assembly. The assembly required is dependent on thetotal wattage used for the unit and hose/applicators in operation. Contact Nordson for assistance in selecting the correcttransformer.
Parameter Part Number
Transformer Base Assembly, 1.5 kVA 1039840
Transformer Base Assembly, 3.0 kVA 1039841
Optional Accessories Parameter Part Number
I/O expansion card kit 1036607
Profibus communications kit 1053300
DeviceNet communications kit 1053288
Ethernet communications kit 1053289
8 Hose/Applicator expansion base (ProBlue 10 only) 1061030
1-3Melters
Adhesives and Sealants GuidePart 1101879A
ProBlue® 4, ProBlue 7 and ProBlue 10 Adhesive Melters (contd)
Maximum hydraulic pressure 87 bar/8.7 MPa (1260 psi)
Hose ports 5 5 9
Hose/Applicator Capacity(Maximum)
2 or 4 2 or 4 2, 4, or 6
Hose/Applicator Power 1000 W each Hose/Applicator pair (2000 W per Hose/Applicator module)
Maximum melter power
� 2 Hose/Applicator
� 4 Hose/Applicator
� 6 Hose/Applicator
4000 W
6000 W
N/A
4200 W
6200 W
N/A
4200 W
6200 W
8200 W
Input/Output Capability Standard 3 standard outputs − programmable for function4 standard inputs − programmable for function
Filter area cm2 (in.2) 71 (11)
Electrical service 200 to 240 VAC 1∅ or 3∅ 50/60 Hz200 to 240 VAC (1∅ N/PE) 50/60 Hz400/230 VAC (3∅ N/PE) 50/60 Hz
With optional transformer 400 or 480 VAC 3∅ 50/60 Hz
Weight kg (lb) (empty) 42 (93) 43 (95) 45 (99)
Dimensions W x H x D mm(in.)
547 x 469 x 318(21.5 x 18.48 x 12.5)
609 x 469 x 322(24 x 18.5 x 12.7)
613 x 505 x 344(24.1 x 19.9 x 13.5)
Service envelopeW x H x D mm (in.)
648 x 502 x 362(25.5 x 19.75 x 14.25)
711 x 564 x 362(28 x 22.2 x 14.25)
714 x 656 x 391(28.1 x 25.8 x 15.4)
Mounting mm (in) 381 x 249 (15.9 x 9.8)
Approvals and certifications UL, CUL(1), CE, ISO 9001
1. CUL is a legal CSA-equivalent in all Canada.
Melter Notes 1. Melter performance ratings are measured using a 1100 cps packaging grade adhesive with an application
temperature of 177 �C (350 �F) and a specific gravity of 0.97.
2. Pump rate is maximum pump output while maintaining 90% of static hydraulic pressure for a given inlet airpressure.
1-4 Melters
Adhesives and Sealants GuidePart 1101879A
This page intentionally left blank.
1-5Melters
Adhesives and Sealants GuidePart 1101879A
ProBlue 15, ProBlue 30 and ProBlue 50 Large Capacity Melters
Description Nordson ProBlue melters are designed to maximizeuptime and reduce operating costs. These rugged,flexible, non-handed melters fit on virtually anypackaging line.
� Melter sizes and service envelopes closely matchlegacy products for easy integration into existingapplications.
� All sheet metal enclosures and large tank openingsease operation and daily maintenance.
� Status-at-a-glance indicators highlight: ready, fault,service and temperature status for tank, hose andapplicator.
� Simplified intuitive controls and service indicatorsrequire less user training and simplify maintenancescheduling.
Maximum hydraulic pressure 100 bar/10 MPa (1450 psi)
Hose ports 9
Hose/Applicator Capacity(Maximum)
2, 4, or 6
Hose/Applicator Power 1000 W each H/G pair (2000 W per H/G module)
Maximum melter power
� 2 Hose/Applicator
� 4 Hose/Applicator
� 6 Hose/Applicator
5000 W
7000 W
9000 W
6000 W
8000 W
10,000 W
6000 W
8000 W
10,000 W
Input/Output Capability Standard 3 standard outputs − programmable for function4 standard inputs − programmable for function
Filter area cm2 (in.2) 71 (11)
Electrical service 200 to 240 VAC 1∅ or 3∅ 50/60 Hz400/230 VAC (3∅ N/PE) 50/60 Hz
With optional transformer 400 or 480 VAC 3∅ 50/60 Hz (ProBlue 15 only)
Weight kg (lb) (empty) 66 (145) 81.6 (180) 87 (192)
Dimensions W x H x D mm(in.)
686 x 547 x 345(27 x 21.5 x 13.6)
952 x 548 x 345(37.6 x 21.6 x 13.6)
952 x 751 x 345(24.1 x 19.9 x 13.5)
Service envelopeW x H x D mm (in.)
787 x 859 x 392(31 x 33.8 x 15.4)
1044 x 859 x 392(41.1 x 33.8 x 15.4)
1044 x 1062 x 392(41.1 x 41.8 x 15.4)
Mounting mm(in)
581 x 249(22.9 x 9.8)
669 x 249(26.3 x 9.8)
Approvals and certifications UL, CUL(1), CE, ISO 9001
1. CUL is a legal CSA-equivalent in all Canada.
Melter Notes 1. Melter performance ratings are measured using a 1100 cps packaging grade adhesive with an application
temperature of 177 �C (350 �F) and a specific gravity of 0.97.
2. Pump rate is maximum pump output while maintaining 90% of static hydraulic pressure for a given inlet airpressure.
1-8 Melters
Adhesives and Sealants GuidePart 1101879A
This page intentionally left blank.
1-9Melters
Adhesives and Sealants GuidePart 1101879A
ProBlue® Fulfill® Integrated Fill System
Description ProBlue Fulfill adhesive melters address the needfor improved operational efficiency and ease of useand automatic filling applications. The system isavailable only in ProBlue 230 VAC small melters (4,7 and 10 liter).
The system automatically maintains desiredadhesive levels and relieves operators fromfrequent refilling of melter tanks. Adhesive level ismonitored by a capacitance sensor mounted inplace of the ProBlue melter’s standard float. Thesystem adds small quantities of adhesive through asuction lance and transfer tubing to the tank atregular intervals. Transferred adhesive can be inthe form of pellets, pastilles or mini−slats. Transferair is exhausted through a hole in the lid and into adisposable filter.
ProBlue Fulfill conveys adhesives up to 12 mm indiameter or 12 x 12 mm square. A vibrator on thesuction lance helps prevent adhesive bridging andthere is an optional vibrator available for moredifficult adhesives.
The system is ideal for production environmentsthat require an integrated filling approach with allcontrols within the ProBlue melter. Installation issimple because the ProBlue Fulfill sensor comesfactory calibrated and the fill timing is preset.
� Factory built and tested
� Clean, streamlined look in keeping with the ProBluemelter design
DescriptionThe easy-to-install and operate Fulfill retrofitsystem kit delivers the benefits of automaticadhesive filling to existing Nordson melters.
A sensor monitors the melter tank adhesive level,alerting the system to add small quantities ofpellets, pastilles, or mini-slats of adhesive whenneeded.
Features
� Automatic adhesive level sensing and filling
� Maintains optimum/full tank adhesive levels
� Indicators for System On, Adhesive Filling inProgress, and Fault
� Easy-to-operate; needs no programming
� Automatic shut-off in fault condition
� Proven, reliable design and performance
� Preset, preassembled components need minimal finetuning
� Choice of melter- or remote-mounted controls andplant or melter power connectivity
� Fixed regulator reduces air consumption
Benefits� Provides uninterrupted production
� Eliminates poor bonding and missed beads due toempty melter tanks
� Minimizes tank and adhesive temperature variationsfor improved bonding
� Saves operator time; reduces exposure to hotadhesives and surfaces
Description Nordson AltaBlue TT melters feature variablespeed AC motors with spur-gear pumps andkey-to-line capability in a compact melter design.AltaBlue TT melters satisfy the need for aneasy-to-operate, low-maintenance melter toprecisely deliver a wide variety of hot meltadhesives. A tubular Teflon-coated tank eliminatesdead corners and minimizes adhesive degradation.The versatile, full-feature control panel offers achoice of programming methods using either thekeypad or arrow keys and intuitively displayssystem status.
AltaBlue TT melters:
� are easy to install
� provide easy day-to-day operation
� service indicators simplify maintenance scheduling
� variable speed pump control and RPM displayprovides key-to−line capability
Maximum hydraulic pressure 75 bar/7.5 MPa (1100 psi)
Hose/Applicator Capacity(Maximum) 2 2 or 4
Maximum system power capacity @240 VAC
� 2 Hose/Applicator
� 4 Hose/Applicator
3355W
N/A
3915 W
5915 W
4415 W
6415 W
Input/Output Capability Standard key-to-line 4 standard inputs − programmable for function
3 standard outputs − programmable for functionkey-to-line
Electrical service2 200 VAC single phase,50/60 Hz
200 to 240 VAC singlephase, 50/60 Hz
200 VAC 1 or 3 phase 50/60 Hz200 to 240 VAC 1 or 3 phase 50/60 Hz
380/415 VAC-Y (3 phase N/PE) 50/60 Hz
Weight (empty) 42 kg (92 lb) 76 kg (168 lb) 80 kg (175 lb)
Dimensions W x H x D mm (in.)
334 x 478 x 552(13.1 x 18.8 x 21.7)
441 x 649 x 620(17.4 x 25.5 x 24.4)
441 x 649 x 620(17.4 x 25.5 x 24.4)
Service envelopeW x H x D mm (in.)
537 x 623 x 908(21.1 x 24.5 x 35.7)
644 x 861 x 1126(25.4 x 33.9 x 44.3)
644 x 861 x 1126(25.4 x 33.9 x 44.3)
Approvals and certifications UL, CUL, CE, ISO 9001
1. Actual rates will vary depending on adhesive type, application parameters and input voltage.
2. Permitted deviation from rated line voltage is �10%.
1-19Melters
Adhesives and Sealants GuidePart 1101879A
AltaBlue Series 15, 30, 50, and 100 Liter Adhesive Melters
Description Nordson AltaBlue Series melters are designed forprecise, demanding hot melt adhesive applications.A choice of single-stream or dual-stream spur-gearpumps with variable-speed AC motors andkey-to-line functionality satisfies a wide range ofmanufacturing requirements. A Teflon-coated tankand reservoir design reduces adhesive degradationwhile maximizing adhesive throughput. Theversatile control panel offers a choice ofprogramming methods using either the keypad orarrow keys.
AltaBlue melters:
� install quickly and easily
� provide easy day-to-day operation
� service indicators simplify maintenance scheduling
� maximize uptime
� independent variable speed pump control provideskey-to−line capability
Up to 2 dual or 4 single stream Up to 4 dual orsingle stream
Pump rate kg/hr (lb/hr)1 & 2 1.4 to 82.1 kg/hr (3 to 180.6 lb/hr) 1.4 to 13.4 kg/hr (3to 29.5 lb/hr)
Filter type Saturn basket-style filter
Temperature range 40−230 �C (100−450 �F)
Ambient temperature range -5−40 �C (23−104 �F)
Temperature control stability �1 �C (2 �F)
Maximum hydraulic pressure 85 bar/8.5 MPa (1233 psi)
Hose/Applicator Capacity(Maximum)
One single-stream manifold: 7 connections
Two single-Stream manifolds: 3 connections per pump stream
Dual-stream manifold: 2 connections per pump stream
Maximum external powercapacity − Maximum load perreceptacle (2 channels)� 6 hose/applicator melters
NOTE: Total external wattagemust not exceed 8,000 W.
1000 W, any single hose or applicator1200 W, any hose/applicator pair2000 W, sum of hose/applicator pairs 1 and 22000 W, sum of hose applicator pairs 3 and 42000 W, any single hose, or applicator 5 or 62000 W, hose/applicator pair 5 or 64000 W, sum of hose/applicator pairs 5 and 6
Maximum external powercapacity − Maximum load perreceptacle (2 channels)
� 8 hose/applicator melters
NOTE: Total external wattagemust not exceed 12,000 W.
1000 W, any single hose or applicator1200 W, any hose/applicator pair2000 W, sum of hose/applicator pairs 1 and 22000 W, sum of hose applicator pairs 7 and 82000 W, any single hose or applicator 3 and 42000 W, any single hose or applicator 5 or 62000 W, hose/applicator pair 3 or 42000 W, hose/applicator pair 5 or 64000 W, sum of hose/applicator pairs 3 and 44000 W, sum of hose/applicator pairs 5 and 6
Input/Output Capability Standard 3 standard outputs − programmable for function4 standard inputs − programmable for function
Electrical service3 230 VAC 3 phase without neutral (Delta) 50/60 Hz400 VAC-Y (3 phase N/PE) with neutral (star-WYE) 50/60 Hz
With optional transformer 400 VAC 3 phase without neutral (Delta) 50/60 Hz480 VAC 3 phase without neutral (Delta) 50/60 Hz
Weight (empty)4
� 2 pump
� 4 pump
200 kg (440 lb) 225 kg (500 lb)
440 kg (970 lb)
250 kg (550 lb)
472 kg (1041 lb) 590 kg (1301 lb)
Dimensions W x H x D mm (in.)
� 2 pump
� 4 pump525 x 1465 x 950 (20.7 x 57.7 x 37.4)
950 x 1465 x 950 (37.4 x 57.7 x 37.4) 1008.7 x 1470 x1261 (39.7 x 57.9
x 49.7)
Service envelope WxHxD mm (in.)
� 2 pump
� 4 pump2355 x 1465 x 2780 (92.7 x 57.7 x 109.5)
2780 x 1465 x 2780 (109.5 x 57.7 x 109.5) 2850 x 1470 x3090 (112.2 x 57.9
x 121.7)
Approvals and certifications CE, ISO 9001
Protection IP33
1. Actual rates will vary depending on adhesive type,application parameters and input voltage.
2. Range given is for maximum pump rate of variouspumps available.
3. Permitted deviation from rated line voltage is �10%.
4. Weight depends on melter configuration
1-22 Melters
Adhesives and Sealants GuidePart 1101879A
AltaBlue Series 15, 30, 50, and 100 Liter Adhesive Melters (contd)
AltaBlue Configuration
BASE MELTER OPTIONSTa
nkC
apac
ity
Vol
tage
Pum
p 1
Pum
p 2
Pum
p 3
Pum
p 4
Hos
e/A
pplic
ator
Flo
wC
ontr
ol
Res
erve
d
Low
Leve
lI
dit
I/OIn
dica
tor
Res
erve
d
Hos
t Com
mu-
nica
tion
Ret
urn
Por
t
Mot
ion
Stit
ch
Sen
sor
Type
Res
erve
d
AB − 030 3 B B B B 6 \ A X L Y X E X X N X X XBoxes
1−2Box
3Boxes
4−6Box
7Box
8Box
9Box10
Box11
Box12
Box13
Box14
Box15
Box16
Box17
Box18
Box19
Box20
Box21
Box22
Box23−25
Base Melter
Box 1−2 AltaBlue
Description Code
AltaBlue Melter AB
Box 4−6 Tank Capacity
Description Code
15 liter 015
30 liter 030
50 liter 050
100 liter 100
NOTE: Max. 2 pumps on 15L. Max 4 pumps on 30, 50and 100L. Dual stream pumps not allowed in any positionon 30/50L three and four pump melters on 100L only.
Box 7 VoltageDescription Code
240 VAC 3P Delta without neutral 3
380−415 VAC Wye 4
400 VAC Delta* without neutral 5
480 VAC Delta* without neutral 6
*With integrated transformer, use 240V hoses andapplicators
Boxes8−11 Pumps
Description Code
SN0030 − 1.4 kg/hr A
SN0046 − 2.2 kg/hr B
SN0062 − 2.9 kg/hr C
SN0093 − 4.5 kg/h D
SN0186 − 8.9 kg/h E
SN0371 − 17.8 kg/hr F
SN0773 − 37.1 kg/hr G
SN1710 − 82.1 kg/hr H
SH0371 − 17.8 kg/hr 9
SH0773 − 37.1 kg/hr Z
DN0030 − 1.4 kg/hr/stream 2
DN0046 − 2.2 kg/hr/stream 3
DN0062 − 2.9 kg/hr/stream 4
DN0093 − 4.5 kg/hr/stream 5
DN0186 − 8.9 kg/hr/stream 6
DN0279 − 13.4 kg/hr/stream 7
SF0016 − 0.8 kg/hr J
SF0030 − 1.4 kg/hr K
SF0060 − 2.9 kg/hr L
SF0090 − 4.3 kg/hr M
SF0120 − 5.7 kg/hr N
SF0175 − 8.4 kg/hr O
SF0240 − 11.9 kg/hr P
SF0300 − 14.4 kg/hr Q
SF0450 − 21.6 kg/hr R
DF0016 − 0.8 kg/hr/stream S
DF0030 − 1.4 kg/hr/stream T
DF0060 − 2.9 kg/hr/stream U
DF0120 − 5.7 kg/hr/stream V
DF0175 − 8.4 kg/hr/stream W
DF0240 − 11.5 kg/hr/stream Y
None
Box12 Hose/Applicator Pairs
Description Code
6 Hose/Applicator pairs 6
8 Hose/Applicator pairs(1) 8(1)Only available on either 100L or 3 and 4-pump 30/50Lconfigurations.
1-23Melters
Adhesives and Sealants GuidePart 1101879A
AltaBlue Series 15, 30, 50, and 100 Liter Adhesive Melters (contd)
Options
Box14 Flow Control
Description Code
Pneumatic Pressure Control Valve (1) A
Circulation Control Valve V
Manual PCV and SV w/ Indication O
Manual PCV X(1)Max 2 SS pumps, DS pumps not allowed
Box16 Low Level Indicator
Description Code
Low Level Indicator L
None X
Box17 I/O Indicator
Description Code
Optional I/O installed Y
None X
Box19 Host Communication
Description Code
Ethernet E
Profibus D
DeviceNet V
None X
Box20 Return Port
Description Code
1 Hose return port R
None X
Box21 Motion Switch
Description Code
Motion Switch M
None X
Box22 Sensor Type
Description Code
Ni-120 N
PT100 P
1-24 Melters
Adhesives and Sealants GuidePart 1101879A
This page intentionally left blank.
1-25Melters
Adhesives and Sealants GuidePart 1101879A
DuraBlue® L Series Adhesive Melters
Description
Nordson DuraBlue melters feature fixed-speed ACmotors with gerotor gear pumps foreasy-to-operate, low-maintenance hot meltadhesive application. A Teflon� coated tube tankeliminates dead corners and minimizes adhesivechar. The versatile control panel offers a choice ofprogramming methods using either a keypad orarrow keys.
� Pump operation can be controlled by a handgun or afootswitch.
� Large accessible tank opening allows easier fillingand cleaner operation.
� Status-at-a-glance indicators highlight: ready, fault,service and temperature status for tank, hose andapplicator.
� Simplified intuitive controls and service indicatorsrequire less user training and simplify maintenancescheduling.
� Quick-disconnect style plugs and pneumatichose/applicator fittings provide quick and easyhook-up of components.
� Disposable filter eliminates routine filter flushing. Allmajor components are easily accessible from thefront of the melter, and all major subsystems areeasily replaced.
� Easy-to-remove exterior panels provide quick andsimple maintenance.
Teflon is a registered trademark of E.I. DuPont de Nemours and
Company
DuraBlue 4L Melter System
DuraBlue melter systems provide everythingneeded to begin adhesive application immediately:melter, hose, handgun and nozzle. The hose andhandgun arrive assembled as a single part. Tobegin using the DuraBlue melter system, simplyconnect the hose/handgun assembly to the melter,mechanically and electrically, and supply powerthrough the attached electrical cord.
A choice of applicators meets virtually any manualor semi-automatic manufacturing requirement. Theapplicator choices provide for a flexibility oftriggering options, either hand or foot control. Aselection of hose lengths provides additionaladaptability to meet specific production needs.
DuraBlue 4L melter systems:
� Ship in a single box
� Are easy to install
� Provide easy day-to-day operation
� Simplify routine maintenance.
Applicator choices include:
� AD−31 handgun
� L6-N handgun/hose
� AD-41 handgun (extrusion or swirl nozzle)
� B900-N applicator with foot switch(extrusion or swirl nozzle)
1-26 Melters
Adhesives and Sealants GuidePart 1101879A
DuraBlue® L Series Adhesive Melters (contd)
DuraBlue L Series
For those who desire the performance and reliability of the DuraBlue series melters and yet do not requirethe sophistication of its programming options, Nordson offers the DuraBlue L series melters.
Specifications for DuraBlue L Series Melters
Parameter DuraBlue 4L DuraBlue 10L DuraBlue 16L
Reservoir type Tank
Pump type Gerotor
Maximum pump rate per hour kg (lb)(1) 22 (48) 22 (48)50 (110)
Weight (empty) 42 kg (92 lb) 76 kg (168 lb) 80 kg (175 lb)
Enclosure rating IPX3
Dimensions W x H x D mm(in.)
344 x 478 x 552(13.1 x 18.8 x 21.7)
441 x 649 x 620(17.4 x 25.5 x 24.4)
Approvals and certifications(6) CE, CUL, ISO 9001
1. Values shown for melter at 60 Hz.
2. Actual rates will vary depending on adhesive type,application parameters and input voltage.
3. Maximum pressure varies by unit.
4. Filter not available on all melters.
5. Permitted deviation from rated line voltage is �10%.
6. Certifications are not universal to all melters. ContactNordson for more information on specific units.
1-27Melters
Adhesives and Sealants GuidePart 1101879A
DuraBlue® L Series Adhesive Melters (contd)
Part Numbers for DuraBlue L Series Melters
L SeriesMelterModel
Hose/
Appli-cator
Pumprate
kg/hr(lb/hr)(1)
MaximumHydraulicPressurebar/MPa
(psi)
Viscosity(cps) Filtered
120V 1� 60 Hz(2)240V 1�
50/60 Hz(3)
PA(4) VITON PA(4) VITON
4L (D4L) 2 22 (48)
75/7.5(1100)
< 30,000Filter 1069732 1031747 1069733 1031750
No Filter − − 1069734 −
10L (D10L) 2 22 (48)75/7.5(1100)
< 30,000 Filter − 1026752 1069735 1026754
10L (D10L) 2 50 (110)41/4.1(600)
< 10,000 No Filter − 1026753 1069736 1026755
16L (D16L) 2 35 (77)75/7.5(1100)
< 30,000 Filter − − 1069737 1031898
16L (D16L) 2 50 (110)41/4.1(600)
< 10,000 No Filter − 1026760 1069738 1026761
1. All pump rates are shown at 60 Hz power supply.Pump rates at 50 Hz are lower and equal to 83% oftheir listed value.
2. All 120V DuraBlue “L” melters include a power cordand U.S., style 20 amp plug.
3. All 200−240V DuraBlue “L“ melters include a powercord without a plug. Wiring color follow internationalstandards.
4. Parts designated as “PA” are recommended for usein product assembly applications with operatingtemperatures greater than191�C (375 �F). PA-type O-rings provideexceptionally high chemical and temperatureresistance.
1-28 Melters
Adhesives and Sealants GuidePart 1101879A
DuraBlue® L Series Adhesive Melters (contd)
DuraBlue 4L System Selection
DuraBlue 4L Systems have a pump rate of 22 kg/hr (48 lb/hr), operate at 600 psi hydraulic pressure, andprocess adhesive with viscosity up to10,000 cps. Filters are not used with these units. The table belowshows the system unit numbers according to available voltage and hose/applicator combination.
Description 120V 1�60 Hz
200V 1�50/60 Hz(1)
240V 1�50/60 Hz
L6 Handgun, Extrusion
L6 Handgun/Hose assembly, 1.5 m (6 ft) — — 1030231
L6 Handgun/Hose assembly, 3 m (10 ft) 1031137 — 1030230
AD-31 Handgun/Hose assembly, 2.4 m (8 ft),1.5 mm (0.06 in.) extended 1042781 — —
AD-31 Handgun/Hose assembly, 3.6 m (12 ft),1.5 mm (0.06 in.) extended 1042782 — —
AD-31 Handgun/Hose assembly, 4.8 m (16 ft),1.5 mm (0.06 in.) extended 1042783 — —
B900-N Manifold Mounted Applicator
B900-N manifold mount extrusion applicator, AC, 0.5 mm (0.02 in.) — — 1030137
B900SW−N manifold mount swirl applicator, AC, 0.6 mm (0.025 in.) CF, air control kit — — 1030138
NOTES: All 120V DuraBlue 4 L Systems include a power cord.
All 200V and 240V systems include a power cord without a plug. Wire colors follow international standards.
Check total external wattage limitation before adding second handgun/hose assembly to DuraBlue 4L 120V units.
The pump rate listed is for 60 Hz power supply. The pump rate at 50 HZ is lower and equal to 83% of the value shown
Processing adhesives with viscosities higher than the stated limit may reduce melter performance.
1-29Melters
Adhesives and Sealants GuidePart 1101879A
DuraBlue® L Series Adhesive Melters (contd)
DuraBlue 4L System Applicator and Hose Part Numbers
Use the table below to order extra or spare Hose/Applicator combinations.
Handgun/Hose Assemblies and Manifold Mount Applicators 120V 240V 200V
L6 Handgun/Hose assembly, 1.5 m (6 ft) — 1027445 —
L6 Handgun/Hose assembly, 3 m (10 ft) 1027442 1027443 —
AD-41 Handgun/HP Hose assembly, 2.4 m (8 ft), 1 mm (0.04 in.) orifice diameter 1030220 1030225 1031160
AD-41 Handgun/HP Hose assembly, 3.6 m (12 ft), 1 mm (0.04 in.) orificediameter
1030221 1030226 1031161
AD-41 Handgun/HP Hose assembly, 4.8 m (16 ft), 1 mm (0.04 in.) orificediameter
1030222 1030227 1031162
AD-31 Handgun/HP Hose assembly, 2.4 m (8 ft), 1.5 mm (0.06 in.) orificediameter
1040109 1044255 1044258
AD-31 Handgun/HP Hose assembly, 3.6 m (12 ft), 1.5 mm (0.06 in.) orificediameter
1040163 1044256 1044259
AD-31 Handgun/HP Hose assembly, 4.8 m (16 ft), 1.5 mm (0.06 in.) orificediameter
1040164 1044257 1044260
B900-N manifold mount extrusion applicator — 1031733 —
B900SW−N manifold mount swirl applicator — 1031734 —
1-30 Melters
Adhesives and Sealants GuidePart 1101879A
This page intentionally left blank.
1-31Melters
Adhesives and Sealants GuidePart 1101879A
DuraBlue Large Capacity Adhesive Melters
Description DuraBlue large capacity adhesive melters aredesigned for simple, low-maintenance hot meltadhesive applications. Production flexibility isprovided by a high-output gerotor pump with achoice of preset speeds for the AC motors.
The grid and reservoir tank design reducesadhesive degradation while maximizing adhesivethroughput. An optional unheated hopper candouble holding capacity to minimize refillingfrequency. The simple, versatile control panel offersa choice of programming methods, using either thekeypad or arrow keys.
� Large, accessible tank opening allows for easierfilling and cleaning.
� Pump shut-off valve and single tool removal providequick, easy pump replacement.
� Quick plug-in hose/applicator pairs provide easyinstallation and replacement of equipment.
� Status-at-a-glance indicators graphically display thetank, hose and applicator status.
� Easy installation and day-to-day operation.
� Easy-open panels make access to meltercomponents quick.
(34.8 x 41.3 x 15.7)1000 x 1382 x 782(39.4 x 54.4 x 30.8)
1100 x 1382 x 1035(43.3 x 54.4 x 40.8)
Approvals and certifications CE, CUL, UL, ISO 9001
1. Rates depend on adhesive characteristics. 2. With integrated transformer, use 240V hoses andapplicators.
1-33Melters
Adhesives and Sealants GuidePart 1101879A
VersaBlue® Adhesive Melters
Description Nordson VersaBlue melters are designed forprecise, demanding hot melt adhesive applications.A choice of metering spur-gear pumps withvariable-speed AC motors satisfies a wide range ofmanufacturing requirements. A grid and reservoirtank design reduces adhesive degradation whilemaximizing adhesive throughput. A highperformance industrial PC provides full control ofthe adhesive system via a touch screen interface.
A higher temperature melter is available for thoseadhesives, such as polyamides, that require higheroperating temperatures for handling.
� Graphic, touch-screen system control with statusdisplay of tank, hose(s) and applicator(s).
� Entry panels make access to melter componentsquick and easy.
� Large, accessible tank opening allows easier fillingand cleaning.
Description Nordson VersaBlue N Series melters are designedfor precise, demanding hot melt adhesiveapplications. The VersaBlue N Series melters areavailable in a standard footprint as well as anexpanded footprint that provides additional holdingand pumping capabilities. A choice of up to foursingle-stream or dual-stream metering spur-gearpumps with variable-speed AC motors satisfies awide range of manufacturing requirements. A gridand reservoir tank design reduces adhesivedegradation while maximizing adhesive throughput.A high performance industrial PC provides fullcontrol of the adhesive system via a touch screeninterface. The VersaBlue N Series melter alsofeatures optional Siemens S7 and Allen-BradleyControlLogix� PLC controls to increase flexibilityand ease integration.
� Graphic, touch-screen system control with statusdisplay of tank, hose(s) and applicator(s).
� Entry panels make access to melter componentsquick and easy.
� Large, accessible tank opening allows easier fillingand cleaning.
None X(1) Nordson (SN/DN) pumps cannot be combined with Feinpruf (SF/DF) pumps(2) Maximum quantity of 2 SN1710 pumps on 12, 25, and 50 L melters
1-43Melters
Adhesives and Sealants GuidePart 1101879A
OPTIONSF
low
Con
trol
Int.
Pre
ssur
eIn
dica
tion
Leve
lC
ontr
ol
Ligh
t Tow
er
Mai
nS
witc
h
Hos
t Com
mu-
nica
tions
Key
-to-
Line
Cas
ters
Res
erve
d
Filt
erS
elec
tion
Res
erve
d
Res
erve
d
Res
erve
d
Dra
in V
alve
Ext
. Pre
ssur
eIn
dica
tor
Hea
tE
xcha
nger
Mot
ion
Sw
itch
App
licat
or S
olen
oid
Con
trol
AC
M
PLC
Res
erve
d
Res
erve
d
Res
erve
d
X X X X X X X XBox14
Box15
Box16
Box17
Box18
Box19
Box20
Box21
Box22
Box23
Box24
Box25
Box26
Box27
Box28
Box29
Box30
Box31
Box32
Box33
Box34
Box35
Box36
Options
Box14 Flow Control
Description Code
Automatic Pneumatic PressureControl P
Manual Pneumatic PressureControl M
Flow Control Bypass F
IPI w/ Output Pressure Controlper Drive C
Automatic Flow control w.Min.−Speed T
Automatic Flow control B
Pressure build up (Airlesspressure control) N
Safety valve with indication only(PCV plugged) O
None (Standard Manual PressureControl) X
Box15 Internal Pressure Indication
Description Code
Internal Pressure Indication (IPI) A
None X
Box16 Level Control
Description Code
Level Monitoring L
Level Control w/ Bulk Feed Lid(Ni-120) B
Level Control w/ Bulk Feed Lid(Ni-120) + Overfill Protection P
Level Control w/ Bulk Feed Lid(PT100) C
Level Control w/ Bulk Feed Lid(PT100) + Overfill Protection D
None X
Box17 Light Tower
Description Code
Light Tower W
None X
Box18 Main Switch
Description Code
Main Switch Red − 4 Pole 1
Main Switch Black − 3 Pole 2
Main Switch Black − 4 Pole 3
None (Standard Main Switch Red− 3 Pole) X
Box19 Host Communications
Description Code
Profibus−DP w PMI D
Control Net w PMI N(1)Ethernet /IP w PMI E
None X(1) Contact NWSG Marketing for availability
Box20 Key-to-Line
Description Code
Key−to−Line per Drive (separateconnectors) K
None (Standard Key−to−Line) X
Box21 Casters
Description Code
Casters C
None X
Box22 Reserved
Description Code
Reserved X
Box23 Filter Selection
Description Code
0.8mm filter with 85 bar safetyvalve C
0.2mm filter with 100 bar safetyvalve D
0.8mm filter with 100 bar safetyvalve G
Standard (0.2mm filter w. 85 barsafety valve) X
Boxes24−26 Reserved
Description Code
Reserved X
Box27 Drain Valve
Description Code
Drain Valve D
None X
Box28 External Pressure Indicator
Description Code
External Pressure Indicator Inputs #
None X
Box29 Heat Exchanger
Description Code
Heat Exchanger E
None X
Box30 Motion Switch
Description Code
Motion Switch M
None X
Box31 Applicator Solenoid Control
Description Code
Applicator Solenoid Control G
None X
Box32 ACM
Description CodeACM Connectivity 1
None X
Box33 PLC(1)
Description Code
Siemens S7−300 with Profibusand TP170 A
A−B ControlLogix w/ ControlNet &PanelView 600+ B
A−B ControlLogix w/ Ethernet andPanelView 600+ C
A−B ControlLogix w/ DataHighway+ and PV600+ D
None X(1) VD, VE, VY, and VZ configurations only
Boxes34−36 Reserved
Description Code
Reserved X
1-44 Melters
Adhesives and Sealants GuidePart 1101879A
This page intentionally left blank.
1-45Melters
Adhesives and Sealants GuidePart 1101879A
VersaBlue XN and XC Series Adhesive Melters
Description VersaBlue XN and XC Series adhesive meltersprovide high speed, high volume hot melt adhesivedelivery in a flexible platform with a wide range ofconfiguration choices. Melters are available in 50,100 and 200 liter tank sizes with twin tankconfigurations available for multiple adhesives.
VersaBlue XN melters target nonwovensdisposable applications by offering twin tanks fordifferent adhesives, multiple metered pumpstreams, control of remote metering stations andapplicators, PLC control, and many auxiliarytemperature control channels.
VersaBlue XC melters target high-consumptionweb coating applications that require high-outputpumps, optional high-precision temperaturecontrols, remote PLC control for coating stands,and several control system choices for wide-webproduction and integration.
VersaBlue XC Melter
VersaBlue XN Melter
� Multiple tank sizes
� Release−coated grid and reservoir
� Up to eight single-stream or eight dual-streamspur-gear metering pumps and variable-speed ACmotors
� Choice of control systems
� Simplified and expanded configuration choices
� Open electrical and hydraulic layout with removableaccess panels
� Common parts with VersaBlue N Series melters
� External control capability for total adhesive systemcontrol
1. Feinpruf pumps cannot be combined with otherpumps.
2. Stated displacement and pump rates are per stream.
3. Available on XC and XN configurations only,
4. Available on XC configurations only.
5. Not available on VersaBlue XN/XC melters.
1-55Melters
Adhesives and Sealants GuidePart 1101879A
VersaBlue N, XN and XC Adhesive Melters Accessories
Fittings and Accessories
Straight Hose Fittings
VersaBlue N melters ship with one 8 mm hose fitting per stream.
Part Number Description
446617 8 mm
419881 13 mm
203786 16 mm
45� Hose Fitting Adapter
Angle adapter fittings to be used in addition to straight fittings.
Part Number Description
250207 8 mm
252075 13 mm
446611 16 mm
90� Hose Fitting Adapter
Angle adapter fittings to be used in addition to straight fittings.
Part Number Description
252582 8 mm
250208 13 mm
289331 16 mm
VersaBlue N Service Kits
Filter Kits
Part Number Description
714265 Filter cartridge, Mesh size 0.2 mm, complete
394590 Service Kit, Filter 0.2 mm
203357 Filter cartridge, Mesh size 0.8 mm, complete
7109691 Service Kit, Filter 0.8 mm
1-56 Melters
Adhesives and Sealants GuidePart 1101879A
VersaBlue N, XN and XC Adhesive Melters Accessories (contd)
Hose Fittings
Part Number Description
446617 Hose fitting a9/16BUNF−a3/4UNF (NW8) 1 O-ring included
419881 Hose fitting a3/4UNF−a3/4UNF (NW13) 1 O-ring included
203786 Hose fitting a1 1.16−12F−a3/4UNF (NW16) 1 O-ring included
Safety Valves
Part Number Description
207932 Safety valve, 85 bar
7106950 Safety valve w/limit switch, 85 bar
394592 Service Kit, Safety Valve
Control Valves
Part Number Description
203059 Pressure control valve, 90 bar, adjustable
207300 Pressure control valve, pneumatically controlled
394600 Service Kit, Pressure Control Valve
Temperature Sensor
Part Number Description
394597 RTD Sensor Ni120 Kit
7116067 RTD Sensor Pt100 Kit
Casters
Part Number Description
394793 Casters Kit 12, 25, and 50L
7104872 Casters Kit 100L
Light Tower
Part Number Description
394794 Light Tower Kit
Interface Connectors
Part Number Description
729678 Standard I/O Interface (XS2) Kit
729677 Key−to−line (X55) Kit
1-57Melters
Adhesives and Sealants GuidePart 1101879A
Extruder Systems
A Nordson Extruder is the first choice when processing ”difficult” adhesives like Polyamide, Polyester orPolyolefin (APAO). These adhesives ask for a closed system to avoid degradation of the adhesive throughcarbonization and consequently loss of bonding performance or other problems within the system.
Extruders enable homogeneous melting in a fully closed ”melt−on−demand” system to provide a safe andreliable application process.
Nordson extruders offer the fastest, easiest adhesive changes possible compared to other melters withouttime− and cost−intensive cleaning procedures.
Convincing advantages at a glance:
� optimized for adhesive applications� a true “melt−on−demand” system, deliver the lowest
possible thermal stress on the adhesive� no degrading or charring at all because it is a fully
closed system� a self cleaning system� virtually maintenance free system
� option to change adhesives during production withina few minutes
� short heat−up times� lower energy consumption per kilogram compared to
conventional tank melters� results in more economical operating costs of the
complete application system
EX Extruder System
The EX extruder systems are for use in applications requiring the highest precision and performance withregard to temperatures and pressures. EX Extruders are designated Engineered Systems, which areengineered to the specific requirements of our customers, offering the highest flexibility and grade ofcustomization for a perfectly suited system.
� Different sizes allows throughput of 1 kg to 2500 kgper hour
� Compact, service−friendly design� PLC control standard: easy integration into existing
production lines� Profibus interface� Ethernet connection for remote diagnostics and
service� Intuitive graphical touch panel in local languages� Provide key−to−line interaction with parent machine
through documented interfaces� Visual display of process data standard� ChemCoat� coated conical feeding hopper provides
safe material supply� Cylinder and screw manufactured from tempered
nitrified steel providing an extremely long lifetime
ChemCoat is a registered trademark of Impreglon GmbH.
1-58 Melters
Adhesives and Sealants GuidePart 1101879A
EX Extruder System (contd)
General Specification
Parameter Description
Melt Rate(1) 1 − 2500 kg/hr (7−5512 lb/hr)
Operating Temperature Range 20−260°C (68−496°F)
Hydraulic Pressure 0−700 bar (0−10,150 psi)
Electrical Connection 3x 400 V +N+PE /50−60Hz
Control System Siemens� S7 PLC with touch panel (5.7 in. or 10.4 in.)
� Start−up circuit that monitors temperature drops andtemperature fluctuations for all heating zones.
� Permanent sensor failure monitoring with visualdisplay.
� zero potential output contacts for reportingtemperature drops and temperature fluctuations, andready for operation signal.
� Electronic pressure control for manual and automaticoperation with excess pressure cutoff.
� Pressure build−up control with automatic switch−overto speed regulation during head control.
Temperature Sensors PT100, Ni-120(2) or Fe−CuNi
Heated Zones Extruder, hose, applicator (additional heating zonesoptional)
Metering Station Metering stations are equipped with high−precision gearpumps for the most demanding applications.
Pumps can be flanged to extruder output or alternativelyas satellite PS Metering Stations with hose betweenextruder and pump station.
(1) The maximum melt rate and throughput depends on the material.
(2) Ni-120 for maximum 180°C.
Siemens is a registered trademark of Siemens. AG.
1-59Melters
Adhesives and Sealants GuidePart 1101879A
Extruder Systems (contd)
EEX Extruder Series While featuring the same general advantages andbenefits in processing demanding adhesives, theEEX series of extruders is a more standardized andconfigurable system.
� Microprocessor−controlled, multi−channeltemperature control featuring staged heating.
� Easy installation and operation.
� Fault diagnostic program for all temperature cycles.
� Start up delay with under- / over-temperature checkfor all heating zones.
� Standard pressure control, optional pump stationwith variable AC drives for metering applications,
� Water cooled draw−in zone, to be supplied bycooling circuitry from customer or optional coolingdevice.
� Cylinder and screw manufactured from temperednitrified steel providing a extremely long lifetime.
� ChemCoat� coated conical feeding hopper providesafe material supply
ChemCoat is a registered trademark of Impreglon GmbH.
Specifications
ParameterSpecification
EEX 10 EEX 40 EEX 100 EEX 200
Rated throughput kg/hr (lb/hr) (1) 10 (22) 40 (88) 100 (220) 200 (440)Hopper Volume L (in.�) 15 (915) 30 (1830) 75 (4576) 150 (9153)Rated Power of main drive kW 2.2 5.5 11 22Max. no. of gear pumps
(re−circulating pumps optional)2 4 4 4
Capacity per pump L/h (lb/hr) 10−40 (22−88) 10−40 (22−88)10−40 (22−88)
40−160 (88−352)(max. 2 pumps)
10−40 (22−88)
40−160 (88−352)(max. 2 pumps)
Max. operating temp. °C (°F) (2) 260 (496)
Max. adhesive pressure bar (psi) 100 (1450)
Temperature sensors Ni-120(3) / PT100 / Fe−CuNi
Hose/Applicator connections 1−5 1−5 1−5 1−4
(1) Maximum output rate depends on adhesive; indication is based on common EVA. (2) Operating Temperature depends on adhesive and auxiliary equipment.(3) Ni-120 for maximum 180°C.
1-60 Melters
Adhesives and Sealants GuidePart 1101879A
EEX Extruder Series (contd)
Configuration Chart
Extruder
Tem
pera
ture
Sen
sor
Fla
nged
Pum
pS
tatio
n
Pum
pM
IDR
Hos
eC
onne
ctio
n
Cod
ing
Dev
ice
Hop
per
Leve
lS
enso
r
Sta
ndby−
Tem
p.S
etba
ck
Wee
k/D
ayTi
mer
Hop
per
Pro
tect
ion
Grid
Cas
ters
Pro
tect
ion
Fra
me
for
Sen
sors
Add
ition
alH
ose/
App
licat
orco
nnec
tions
Spe
cial
Req
uest
Box1
Box2
Box3
Box4
Box5
Box6
Box7
Box8
Box9
Box10
Box11
Box12
Box13
Box14
Box1
Extruder Size
Description Code
EEX Extruder 10 kg/hr EEX 10
EEX Extruder 40 kg/hr EEX 40
EEX Extruder 100 kg/hr EEX 100
EEX Extruder 200 kg/hr EEX 200
Box2
Temperature Sensor
Description Code
FeCuNi F
PT100 P
Typ NI 120(1) N(1) Up to 180°C.
Box3
Flanged Pump Station
Description Code
No Pump station (pressurecontrolled)
0
Single pump station (1 pump) 1
Single pump station withre−circulating ports (1 out/1 in)*
2
Double pump station (2 pumps) 3
Double pump station withre−circulating ports (2 out/2 in)*
4
Quadruple pump station (4 pumps)not possible with EEX10
5
*Only in combination with a re−circulatingapplicator.
Box4
Pump MIDR
Description Code
No pump selected X
10 l/h max. per pump(1) (2) A
20 l/h max. per pump(1) (2) B
40 l/h max. per pump(1) (2) C
80 l/h max. per pump(1) (2) (3)
(EEX 100 /EEX 200 only)D
160 l/h max. per pump(1) (2) (3)
(EEX 100 /EEX 200 only)E
220 l/h max. per pump(1) (2) (3)
(EEX 200 only)H
(1)Pump selection only possible if pump stationselected.(2)All pumps have to be same size.(3)Pump D and E only possible up to 2-pumpstation!
Box5
Hose Connection
Description Code
Hose connection 8 mm diameter 1
Hose connection 13 mm diameter 2
Hose connection 16 mm diameter 3
Hose connection 20 mm diameter 4
Hose connection 32 mm diameter 5
Box6
Cooling Device
Description Code
No cooling device X
Stand−alone cooling device*(EEX 10 /EEX 40 only) K
Cooling device on extruder frame*(EEX 100 /EEX 200)
R
*Mandatory if customer doesn’t supply coolingwater circuit.
1-61Melters
Adhesives and Sealants GuidePart 1101879A
EEX Extruder Series (contd)
Box7 Hopper Level Sensor
Description Code
No level sensor X
1 Level sensor (Hopper empty) 1
2 LS (Hopper empty + Hopper lowlevel)
2
3 LS (Hopper empty + Hopper lowlevel + Hopper full)
3
Box8
Standby Temperature − Setback
Description Code
No Standby/setback X
Standby / Setback Option* T
Box9
Week/Day Timer
Description Code
No Week/Day timer X
With Week/Day timer* W
*For automatic startup and shutdown of theextruder.
Box10
Hopper Protection Grid
Description Code
No prot. grid(when AutoFill) X
With protective grid* G
*Mandatory if hopper is filled manually.
Box11
Casters
Description Code
No casters, just feet X
with casters M
Box12
Protection Frame for Sensors
Description Code
No protection frame X
With protection frame Q
Box13
Additional Electrical Hose/Applicator Connectors*
Description Code
No add. H/A connector X
One add. H/A connector 1
Two add. H/A connectors 2
Three add. H/A connectors 3
Four add. H/A connectors(not for EEX 200)
4
*Maximum number of connections depends onPump Station, refer to table below.
Box14
Special Request
Description Code
No Special Request X
Any special need to be specified andquoted upon request
T
Pump Station Table
Standard Number of Hose/Applicators
Additional Electrical Hose/ApplicatorConnectors
CodeBox 3
DescriptionEEX10EEX40
EEX100 EEX200
0 No Pump station (pressure controlled) 1 4 4 3
1 Single pump station (1 pump) 1 4 3 3
2Single pump station with
re−circulating ports (1 out/1 in)*2 3 2 2
3 Double pump station (2 pumps) 2 3 2 1
4Double pump station with
re−circulating ports (2 out/2 in)*4 1
5Quadruple pump station
(4 pumps)4
*Only in combination with a re−circulating applicator.
1-62 Melters
Adhesives and Sealants GuidePart 1101879A
EEX Extruder Series (contd)
Gear Pump Chart
PartNumber Type Layout
Dimensions(mm) Capacity
(cc.rev)
Output@100rpm
(L/hr)A B C
EE
X 2
00
EE
X 1
00
EE
X 1
0E
EX
40
7521694 GP 03 M0.5 3 76 76 0.2 1.2
7521751 GP 03 M1 3 76 76 0.4 2.4
7521755 GP 03 M2 3 76 76 0.8 4.8
7521703 GP 06 M2 6 76 76 1.7 10.2
7528130 GP 12 M2 12 76 76 3.5 21
7521668 GP 25 M2 25 76 76 7 42
7055336 GP 30 M2 30 76 76 8.4 50.4
7523855 GP 50 M2 50 76 76 13.3 80
7053428 GP 100 M1 15 195 120 16.7 100
7525111* GP 160 M2 25 195 120 27 162
7522285* GP 220 M2 35 195 120 37 222
*additional heating cartridges needed
Dimensions (in millimeters)
EEX 100
EEX 10/EEX 40
ApplicatorPlug End
Unit Plug End
1-63Melters
Adhesives and Sealants GuidePart 1101879A
Extruder Systems (contd)
Extruder Hoses Type PC
� Extremely robust and flexible design� High Temperature PTFE hose up to 250°C� High pressure versions up to 300 bar available� PT100 or FE−CuNi temperature sensors� PTFE insulated heating wires for highest safety� High−efficient thermo−fleece insulation with outer
foamed sleeve� Other special versions on request
DescriptionPart
Number
LengthComment
SupplyVoltage
VM FT
Automatic High Temperature Hose, PT100, 250°C
8 m
m(.
312
in.)
ID
PC 12−08 PT−H 7052360 1.2 4.0 230
PC 18−08 PT−H 7052197 1.8 6.0 230
PC 24−08 PT−H 7050155 2.4 8.0 230
PC 30−08 PT−H 7052382 3.0 10.0 230
PC 40−08 PT−H 7504182 4.0 13.0 230
PC 50−08 PT−H 7500888 5.0 17.0 230
13 m
m(.
500
in.)
ID
PC J 12−13−PT−H 7052056 1.2 4.0 200
PC 13−13 PT−H−K 7052650 1.3 4.0 no applicator connector 230
PC 18−13 PT−H−K 7504183 1.8 6.0 no applicator connector 230
PC 18−13 PT−H 7504298 1.8 6.0 230
PC 20−13 PT−H−K 7052791 2.0 7.0 no applicator connector 230
PC 24−13 PT−H−K 7052359 2.4 8.0 no applicator connector 230
PC 24−13 PT−H 7050153 2.4 8.0 230
PC 30−13 PT−H 7050216 3.0 10.0 230
PC 40−13 PT−H 7050176 4.0 13.0 230
16 m
m(.
629
in.)
PC 24−16−PT−H 7050233 2.4 8.0 230
20 m
m(.
787
in.)
PC 90−20 PT−H−K 7500717 9.0 30.0 no applicator connector 230
1-64 Melters
Adhesives and Sealants GuidePart 1101879A
Extruder Hoses Type PC (contd)
DescriptionPart
Number
LengthComment
SupplyVoltage
VM FT
Automatic High Temperature Hose, FE−CuNi, 250°C
8 m
m(.
312
in.)
ID
PC J 12−08 FE−H 7501231 1.2 4.0 200
PC 15−08 FE−H 7052662 1.5 5.0 230
PC 18−08 FE−H 7050021 1.8 6.0 230
PC J 18−08 FE−H 7501222 1.8 6.0 200
PC 24−08 FE−H 7500885 2.4 8.0 230
PC 24−08 FE−H−K 7501183 2.4 8.0 No applicator connector 230
PC J 24−08 FE−H 7501226 2.4 8.0 200
PC 30−08 FE−H 7501180 3.0 10.0 230
PC J 30−08 FE−H 7501227 3.0 10.0 200
PC 36−08 FE−H 7053265 3.6 12.0 230
PC J 40−08 FE−H 7052064 4.0 13.0 200
PC 40−08 FE−H 7501186 4.0 13.0 230
PC 50−08 FE−H 7500884 5.0 17.0 230
PC 60−08 FE−H 7052528 6.0 20.0 230
13 m
m(.
500
in.)
ID
PC 10−13 FE−H 7053247 1.0 3.0 230
PC 12−13 FE−H−3 7052858 1.2 4.0 High pressure 300 bar 230
PC J 12−13−FE−H 7052055 1.2 4.0 200
PC 12−13 FE H−K 7501187 1.2 4.0 No applicator connector 230
PC 18−13 FE−H−K 7053270 1.8 6.0 No applicator connector 230
PC 24−13 FE−H−K 7053279 2.4 8.0 No applicator connector 230
PC 24−13 FE−H 7050235 2.4 8.0 230
PC 30−13 FE−H 7050236 3.0 10.0 230
PC J 30−13−FE−H 7050228 3.0 10.0 200
PC J 40−13 FE−H 7052075 4.0 13.0 200
PC 40−13 FE−H 7501185 4.0 13.0 230
PC 50−13 FE−H 7501184 5.0 17.0 230
PC J 60−13 FE−H 7052132 6.0 20.0 200
20 m
m(.
787
in.)
PC 12−20 FE−K−H−3 7052535 1.2 4.0 No applicator connectorHigh pressure 300 bar 230
PC 18−20 FE−H 7052525 1.8 6.0 230
PC 24−20 FE−H 7052613 2.4 8.0 230
PC 24−20 FE−K−H−3 7052534 2.4 8.0 No applicator connectorHigh pressure 300 bar 230
PC 30−20 FE−H−K 7052497 3.0 10.0 No applicator connector 230
PC 60−20 FE−H 7052498 6.0 20.0 230
PC 60−20 FE−H−K 7052753 6.0 20.0 No applicator connector 230
PC 70−20 FE−H 7501188 7.0 23.0 230
32 m
m(1
.25
in.)
PC 40−32 FE−H−3 7052334 4.0 13.0 No applicator connectorHigh pressure 300 bar 230