16 KHK Stock Gears Selection Methods 2. Select by Application ■ High Precision Gears with Excellent Low Noise Qualities ■ Quenched, Ground Gears with High Durability OKUMA 2SP-25HG Lathe machine with output of φ 100 to 200 mm. Can be operated 24-hours a day by attaching a loader that pro- duces 150 to 300 units per day. KHK gears (KRGD and MSGA) are used. Machine Application Example Recommended Products Precision Roll Feeder A machine for cutting off stainless steel belts at des- ignated lengths. KHK gears (SSG) are used in the feeding device of the servomotor. Machine Application Example Recommended Products MSGA・MSGB Ground Spur Gears m1 ~ 4 Page 34 KHG Ground Helical Gears m1 ~ 3 Page 168 KRHG・KRHGF Ground Helical Racks m1 ~ 3 Page 220 Page 198 SRG・SRGF・SRGFD・SRGFK m0.5 ~ 6 Series Ground Racks SSG Ground Spur Gears m0.5 ~ 6 Page 48 Series SMSG Ground Spiral Miter Gears m1 ~ 5 Page 258 SBSG Ground Spiral Bevel Gears m2 ~ 4 Page 290 Gear Ratio 1.5 ~ 3 KRGF-H・KRGFD-H Hardened Ground Racks Series Page 196 m1.5 ~ 3 Series Newly added Series Series Newly added Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected]ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18 Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected]ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
13
Embed
2. Select by Application Low - Maryland Metrics · 2. Select by Application ... (Machine Model SK-6). KHK gears (SW and CG) ... Definition of Bending Strength The allowable bending
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
16
KHK Stock Gears Selection Methods
2. Select by Application
■ High Precision Gears with Excellent Low Noise Qualities
■ Quenched, Ground Gears with High Durability
OKUMA 2SP-25HGLathe machine with output of φ 100 to 200 mm. Can be operated 24-hours a day by attaching a loader that pro-duces 150 to 300 units per day. KHK gears (KRGD and MSGA) are used.
Machine Application Example
Recommended Products
Precision Roll FeederA machine for cutting off stainless steel belts at des-ignated lengths. KHK gears (SSG) are used in the feeding device of the servomotor.
Machine Application Example
Recommended Products
MSGA・MSGBGround Spur Gears
m1 ~ 4 Page 34
KHGGround Helical Gears
m1 ~ 3 Page 168
KRHG・KRHGFGround Helical Racks
m1 ~ 3 Page 220
Page 198
SRG・SRGF・SRGFD・SRGFK
m0.5 ~ 6
Series
Ground RacksSSG
Ground Spur Gears
m0.5 ~ 6 Page 48
Series
SMSGGround Spiral Miter Gears
m1 ~ 5 Page 258
SBSGGround Spiral Bevel Gears
m2 ~ 4 Page 290
Gear Ratio 1.5 ~ 3
KRGF-H・KRGFD-HHardened Ground Racks
Series
Page 196m1.5 ~ 3
Series
Newly added
Series
Series
Newly added
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
17
■ Antirust and Oil-free Components
■ High Reduction, High-load Gears
F-T200 High-speed vegetable cutting machine, by DREMAX Inc.A high-precision vegetable cutting machine with a force-feed device used to produce sushi (sashimi) garnishes. To use this machine, just cut off both sides of a Daikon radish, and set to Daikon cutting, the machine performs automatically. In addition, handles two radishes at one time, for doubled efficiency. Our Gear Products (PR and PS) are used in this machine.
Machine Application Example
Recommended Products
Yaesu Steam KettleA food processing machine with water holding capacity of 360L and cooking capacity of 216kg (Machine Model SK-6). KHK gears (SW and CG) are used in this ma-chine.
Machine Application Example
Recommended Products
Sp
urG
ears
Hel
ical
Gea
rsIn
tern
alG
ears
Rac
ksC
P R
acks
& P
inio
nsM
iter
Gea
rsB
evel
Gea
rsS
crew
Gea
rsW
orm
Gea
r P
air
Bev
elG
earb
oxe
sO
ther
Pro
duc
ts
SUS・SUSAStainless Steel Spur Gears
m1 ~ 4 Page 114
Series
Stainless Steel Racks
Page 212
SUR・SURF・SURFD
m1 ~ 4
Plastic Racks
Page 216
PR・PRF
m1 ~ 3
PS・PSAPlastic Spur Gears
m1 ~ 3 Page 140v
Series
MHPHigh-Ratio Hypoid Gears
m1, 1.5 Page 288
Gear Ratio 15 ~ 200
CGGray Iron Worm Wheels
m1 ~ 6 Page 374
Reduction Ratio 10 ~ 120
BGBronze Worm Wheels
m0.5 ~ 6 Page 372
Reduction Ratio 10 ~ 60
SWSteel Worms
m0.5 ~ 6 Page 372
Series
For updated information see KHK Web Catalog
Series
Newly added
Series
Newly added
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
18
■ Mount the Gears on the Shaft with a Single Touch
Page 348
2. Select by Application
■ Components with Backlash ConsiderationsExample
KWGDL・KWGDLSDuplex Worms &
Worm Wheels
m1.5 ~ 4 Page 348
AGDLDuplex Worm Shafts &
Worm Wheels
m1.5 ~ 4 Page 348
Reduction Ratio 20 ~ 60
The usual method of adjusting the backlash of a worm gear assembly is to modify the center distance. Once assembled, such adjustment requires a major rework of the gear housing. The use of duplex worm gears and worm wheels allows backlash adjustment to be made by axially shifting the worm. This simplifies greatly the assembly and mainte-nance operations.
■ Description of Duplex Worm Gear Pair
These are designed so that moving the pinion axially by 1mm changes the backlash by 0.05mm.
Features
These are designed so that moving the pinion axially by 1mm changes the backlash by 0.02mm.
Features
Duplex Worms & Worm Wheels
Example
KTSCP Tapered Pinions
CP5, 10 Page 230
CPSTRCPF・STRCPFD
Tapered Racks
CP5, 10 Page 230
CP
● A SRCP5-1000 and SSCP5-30 combination produces backlash values of 0.1 to 0.26.● STRCPF5-1000 and KTSCP5-30 combination can have the backlash value of 0.05 or less. (Target value)
■ Examples
Tapered Racks & Pinions
Example
DSLAcetal Fairloc Hub Spur gears
m0.5 ~ 1 Page 124
SUSLStainless Steel Fairloc
Hub Spur Gears
m0.5 ~ 1 Page 120
SSAY/KSpur Gears with Built-In Clamps
m0.8, 1 Page 106
■ Special Features● Possible to mount repeatedly without marring the shafts.● The component consists of one screw; this simple construction leads to lower costs.● Machining of shafts or auxiliary mounting hardware is not necessary.● Especially suitable when positional adjustment is needed after assembly.
Page 230
Page 120Page 124
Page 108
KHK Stock Gears Selection Methods
4°
Tapered Pinion
Tapered Rack
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
19
● Characteristics of Racks & PinionsAdvantages Description
Simple component including a small number of parts This simple component does not include parts such as balls or retainers, so there is no concern about missing pieces when assembling or disassembling.
Capable of handling large loads Racks with large modules can be used in large loadings.
Compact component systems can be created Allows compact component usage for light loads, while downsizing is possible, more than a ball screw mechanism.
High power transmission efficiency Approximately 98% power transmission efficiency is implemented. (Resistance against lubricant agitation or bearing is not included.)
Rapid feeding It enables quick feeding if the pinion has a large radius,
Has no limitation in length Racks can be joined lengthwise, conversely, in case of using a screw mechanism, defection must be considered and the maximum length should be within 2 meters.
Designed for flexibly Flexibly designed within certain conditions, materials, heat treatments, shapes etc., easily adapting to most machines.
High accuracy Applying tooth-grinding, pitch errors can be lessened
Used in food machine equipments MC Nylon Plastic or Stainless Steel products are available.
Disadvantages DescriptionBacklash evident For smooth revolution, essential backlash is required. In the case of positioning forward reverse revolution, backlash is not a concern.
Lubrication required Lubrication is necessary for metal racks. For plastic racks, using light loads, lubrication is not required, however, accuracy is low.
● Characteristics of Ball ScrewsAdvantages Description
High power efficiencytransmission High power transmission efficiency, exceeding 90%.
High accuracy Grinding treatment allows the creating of high-precision ball screws.
Rapid feeding High-helix lead screws enable rapid feeding.
No backlash is present Pressurizing eliminates backlash.
Disadvantages DescriptionLimited in length Practical limit would be approximately 2m due to warpage.
Special purposes are difficult to create. Since it is difficult to create special-purpose ball screws, the machine must be set up in accordance with the shape of the ball screw.
Functional Comparison of Linear Motion Mechanisms
■ Convenient Positioning in Linear Motion ApplicationsExample
SSCPG Ground Spur Gears
CP5 ~ 20 Page 236
CPSSCP
Spur Gears
CP2.5 ~ 20 Page 244
CPSRCP・SRCPF・SRCPFD
Racks
CP2.5 ~ 20 Page 246
CPSRGCP・SRGCPF・SRGCPD
Ground Racks
CP5 ~ 20 Page 236
CP
Series
Movement of one cycle of the CP10-30 pinion on a CP rack vs.SS3-30 (m3) on a m3 rack.
Difference between CP10 and m3
One half turn
One turn
Pitch
The reference pitch of a metric module is computed by multiplying the number of module by π(3.14159). For example, the reference pitch of m3 rack is 9.425mm (3 x π). When using a rack and a pinion in linear motion applications, the fact that the pitch is not an integral number presents a difficulty in accurate positioning. This problem is solved by using circular pitch racks and pinions where one rotation of a pinion moves it precisely 50, 100, 150, to 600. The difference in movement of one rotation of 30-teeth CP10 vs. SS3 spur gears is illustrated on the left.
■ About CP Racks & Pinions
Table
Stroke
Linear Guide
Motor bracket
Base
Motor
Rack
Pinion
Motor
Table
RackPinion
Stroke
Table
Base
Motor
Motor bracketLinear Guide Support Unit (Fixed-side)
Coupling
Ball Screw Shaft Ball Screw Nut
Nut Bracket
Support Unit (Supported-side)
Page 226
Sp
urG
ears
Hel
ical
Gea
rsIn
tern
alG
ears
Rac
ksC
P R
acks
& P
inio
nsM
iter
Gea
rsB
evel
Gea
rsS
crew
Gea
rsW
orm
Gea
r P
air
Bev
elG
earb
oxe
sO
ther
Pro
duc
ts
The basic mechanism of rack gears allows flexibility in the design of materials, heat treatments, strength and accuracy parameters, all in accordance with environmental conditions. Further, this arrangement leads to low-cost maintenance, and selective replacement is possible without the purchasing of an entire set of components. For designing linear motion mechanisms, use the following information about their features as reference.
Series
Newly added
Series
Newly added
Series
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
20
3. Select by Gear StrengthGear Strength is one of the most important factors inselecting gears.
■ Definition of Bending Strength
The allowable bending strength of a gear is defined as the al-lowable tangential force at the pitch circle based on the mu-tually allowable root stress of two meshing gears under load.
Example of failure due to insufficient bending strength.
■ Definition of Surface Durability
The surface durability of a gear is defined as the allowable tan-gential force at the pitch circle, which permits the force to be transmitted safely without in-curring surface failures.
Example of defacement due to insufficient surface dura-bility.
Step 1 Approximate the type of gear, strength and torque load.
Step 2 Make a tentative selection based on the torque load using the printed version of the KHK catalog, or the Web catalog.
■ The KHK catalog is used for the tentative selections. ■ The Web catalog is used for the tentative selections.
Step 3 After calculating the required strength using the actual conditions of usage, examine the se-lection mode in Step 2.
If the Web catalog is used, the strength can be easily confirmed.
Also, please refer to “Safety Considerations when Selecting Gears” . (Page 27)
Sp
urG
ears
Hel
ical
Gea
rsIn
tern
alG
ears
Rac
ksC
P R
acks
& P
inio
nsM
iter
Gea
rsB
evel
Gea
rsS
crew
Gea
rsW
orm
Gea
r P
air
Bev
elG
earb
oxe
sO
ther
Pro
duc
ts
KHK Stock Gears Selection Methods
For KHK Stock Gears, see page 11
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
21
KHK Stock Gears Selection Methods
4. Selection by novices
Please select product series from the performance / price indication chart below.
* Please read through the selection / application hints in the pages of each product series, based on your selection. Also, please refer to the product specifications in the dimensional table for selecting gears fitting your requirements in mind.
P29P163P181
P187P187P225
P251P281
P325P339
Motion Direction Parallel Axes Linear Motion Nonparallel &Nonitersecting AxesIntersecting Axes
Product Groups
Features
Spur GearsHelical GearsInternal Gears
RacksHelical RacksCP Racks
Miter GearsBevel Gears
Screw GearsWorm Gear Pairs
RegularAnti rust Unlubricated
HighPerformance
Low Cost
Regular Anti rust Unlubricated Regular Anti
rust Unlubricated Regular Anti rust Unlubricated
■ The Web catalog is used for the tentative selections.
Sp
urG
ears
Hel
ical
Gea
rsIn
tern
alG
ears
Rac
ksC
P R
acks
& P
inio
nsM
iter
Gea
rsB
evel
Gea
rsS
crew
Gea
rsW
orm
Gea
r P
air
Bev
elG
earb
oxe
sO
ther
Pro
duc
ts
Sp
urG
ears
Hel
ical
Gea
rsIn
tern
alG
ears
Rac
ksC
P R
acks
& P
inio
nsM
iter
Gea
rsB
evel
Gea
rsS
crew
Gea
rsW
orm
Gea
r P
air
Bev
elG
earb
oxe
sO
ther
Pro
duc
ts
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
22
Index
■ Feature IconsRoHS Compliant Prod-uct
Stainless Product
Re-machinable products
Resin Product
Finished Product
Copper alloy Product
Heat Treated Product
Injection Molded Product
Ground Gear
Black Oxide Coated Product
Series Gear Type Page Features
A AG Worm Wheels 354~357,364~371AGDL Duplex Worms Wheels 348~353AGF Worm Wheels 358~363AN Aluminum-Bronze Screw Gears 334~335ARL Rack Guide Rails 219
B BB Sintered Metal Bushings 154,279,314BG Bronze Worm Wheels 372~373BSR Brass Racks 216BSS Brass Spur Gears 156~161
C CBX Bevel Gearboxes 404~407CG Gray Iron Worm Wheels 374~387 Series
D DB Injection Molded Bevel Gears 314~315DG Plastic Worm Wheels 388~389DM Injection Molded Miter Gears 278DR Molded Flexible Racks 218~219DRF Plastic Racks 214~215DRFD Plastic Racks 214~215 Series
Nylon gears are a plastic waste. Please dispose as a reusable industrial waste.
Please recycle cardboards used as packing.
Please recycle paperboards used as packing.
Packing materials like plastic bags, mirrors and boxes are plastic waste. Please dispose as a reusable industrial waste.
An appeal from KHK for the disposal of KHK Stock Gears and packing materials
RoHS Compliance
MSDS ActivitiesIn regards to environmental issues, rust preventive oil and packing materials, which are used in the production of our products, are managed by safety data sheets similar to the disposal management of chemicals.
Green Purchasing70 percent of office supplies we purchase are made of environmentally friendly materials.
For details, please refer to the Page 432 and KHK Environmental Policy.
RoHS Compliance
Restriction of Hazardous Substances
RoHS is a compliance ordinance established by the European Par-liament / European Commission.
The following six substances are regulated by usage due to environ-mental considerations.
Allowable maximum density of these six substances for RoHS compliance Cadmium:0.01wt%(100ppm) Lead:0.1 wt%(1000ppm) ※ Exception depending on usage Steel 0.35 wt% , Aluminum 0.4 wt% , Copper alloy 4 wt% Mercury:0.1 wt%(1000ppm) Hexavalent chromium:0.1 wt%(1000ppm) PBB(Polybrominated biphenyl):0.1 wt%(1000ppm) PBDE(Polybrominated diphenyl ether) :0.1 wt%(1000ppm)
Products can not be ex-ported to EU countries without following.
Compliant !※ Products only in the KHK Stock Gear series are RoHS compliant. For customized gears, please make the request when asking for a quote.
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
27
Safety Considerations when Selecting KHK Stock Gears
To select KHK Stock Gears, please be sure to carefully con-sider the characteristics of the items and contents of the product table in each section of a product series.
As for items not in this catalog or products having specifi-
cations (material, modules, tooth number etc.) not shown
in the dimension tables, KHK handles custom-made gear
product requests. To order custom-made gears, please
refer to the information on the page 8.
Caution in regards to the special characteristics is de-
scribed in each dimension table in the product information
page. Please read carefully to understand the correct specifications and select suitable gears
properly.
When selecting gears with angled teeth, please be careful and understand the helix direc-
tion of the mating gear. These gears cannot be installed with an improper orientation. For
details, please refer to the information in the first page of each product series.
There might be cases that the products shown in each product information page are different
from the actual shown products, in color or shape. Especially for shapes, please be sure and
check the information in the dimension tables.
For the purpose of modifications, there are cases where specifications or dimensions are
changed without notice. The most updated information is published on the KHK Web Catalog,
at our official web site. Keep up to date, by visiting the web site. Thank you very much.
□ www.khkgears.co.jp/en/web_catalog/index.html
We publish any changes and corrections to the catalog on our web site. Keep up to date,
For ordering KHK Stock Gears, please place an order by letting us know the catalog number of each item. You will find explanations about the catalog number in the first page of each product series.
For more information, please visit our web site, or contact MARYLAND METRICS email: [email protected] web: http://mdmetric.com
Attention
Sp
urG
ears
Hel
ical
Gea
rsIn
tern
alG
ears
Rac
ksC
P R
acks
& P
inio
nsM
iter
Gea
rsB
evel
Gea
rsS
crew
Gea
rsW
orm
Gea
r P
air
Bev
elG
earb
oxe
sO
ther
Pro
duc
ts
●
●
●
●
●
●
■
■
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
28
Safety Considerations when Using KHK Gears
In order for our customers to use our products safely:
Warning Protection of Body and Property
Please feel free to contact:
1. Follow all applicable safety regulations (Labor, Safety, and Sanitation Regulations) in in-stalling and operating our products.
2. Adhere to the following procedures when installing, dismantling or inspecting our prod-ucts.① Turn off the power.② Do not place any part of your body in harm's way.③ Wear proper attire and protective gear appropriate for the task.
We consider safety to be of utmost importance. Please consider the following issues in order to prevent danger in handling, assembling, and operating KHK products.
Attention Prevention of Accidents1. Please read the “CAUTION” notes before using our products in your applications.2. Please avoid using the products in an environment where it may cause adverse effects.3. KHK Products are made in accordance with ISO 9000 Quality Standard. However, if any
defective products are found, please contact the dealer.
Precautions on Starting Operations1. Before operating, check the following:
① Are the gears firmly mounted on the shafts? ② Have you eliminated uneven tooth contact?
③ Does the gear mesh have a proper amount of backlash? (Please avoid the condition of no backlash)
④ Is there sufficient lubrication?2. If the gears are exposed, install a safety cover for protection. Never touch gears while they are in motion.3. The following are the gear lubrication methods for general use.(a) Grease Lubrication(b) Splash Lubrication (Oil Bath Method)(c) Forced Oil Circulation Lubrication
Check lubrication after start up, sometimes, when the unit is initially being operated, lubricating oil deteriorates rapidly. 4. If there is unusual noise or vibration at the start up, please recheck the gears and correctness of the assembly. Some of the
methods for achieving noise reduction are:(a) High Precision(b) Fine Tooth Surface Finish(c) Accurate Tooth Contact
1. KHK products are individually packaged to avoid damage during shipping. In case you find rust, scratches, dents or other problems when you unpack your gears, please contact the dealer where you made your purchase.
2. Depending on how they are handled, it is still possible to deform or break gears. Please be sure to handle gears care-fully, especially the long racks or ring gears, as they are easily deformed.
1. KHK Gears are designed so to give the proper backlash as long as assembled in accordance with the normal value (theoretical values) of the center distance. For a pair of gears, the center distance tolerance is specified to the plus side of tolerances H7 to H8. However, in case of using multiple gear trains, please aim for near-zero by setting to a plus-tol-erance, or minus-tolerance.
2. When you assemble gears, please read through the information “Points of Caution in Assembling” on the first page of each product series section.
1. We can not guarantee the precision of gears once a customer performs a modification (secondary operation) on any gears.
2. When you apply additional secondary operations on KHK Stock Gears, please read through the information “Cautions on Performing Secondary Operations” on the first page of each product series section.
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18
Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA web: http://mdmetric.com email: [email protected] ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 rfq form: http://mdmetric.com/rfq.htm
How to order: Please preface each KHK part number with 'R070K-' Example (using the part number): R070K-MSGA1-18