1TE34

8/20/2019 1TE34

1/24

Rev. 08-17-10

Page 1 of 24 999Q6 VX800II

GENUINE PARTS

INSTALLATION INSTRUCTIONS

5. PRE-INSTALLATION CAUTION / NOTES:

1. DESCRIPTION: In-mirror RearView Monitor

2. APPLICATION: 370Z Roadster (2010)

3. PART NUMBER: 999Q6 VX300

4. KIT CONTENTS:

Item Qty Description Service Part Number

A 1 In-mirror RearView Monitor 999Q6 VX200

B 1 Camera 999Q6 VV030

C 1 Parts Kit 999Q6 VX600SP (Items D - P)

D 1 Harness

E 1 Camera BracketF 1 Wire Cover

G 20 Wire Tie

H 18 Foam Tape

I 4 Butyl Gum

J 2 Posi-Tap™

K 2 Well Nut

L 2 M3 x 6mm Phillip Screw

M 2 M4 X 12mm Phillip Screw

N 1 User Guide

O 1 Manual, Installation Instruction Download 999V2 AW000

P 1 A-Pillar Clip 76988 JM00A

CAUTIONDealer installation recommended. This installation instruction will reference the service manual.•

This is a universal installation kit so all parts may not be used.•

Cut the excess wire tie(s) as ush with the head as possible. Face head of cable tie away from sheet•

metal and other objects.

Use caution when removing/re-installing interior components to avoid damage, scratches, or breaking of•

mounting clips.

!

WARNING

Disconnect vehicle battery before installing RearView Camera Kit to prevent possible shock injury during•

installation.

!

HOMELINK® AND THE HOMELINK HOUSE® ARE REGISTERED TRADEMARKS OF JOHNSON CONTROLS, INC.

8/20/2019 1TE34

2/24

Rev. 08-17-10

In-mirror RearView Monitor - 370Z Roadster


7. VEHICLE PREPARATION:

Apply parking brake.1)

Record the customer radio presets.2)

Make sure that the shift lever is engaged in the “P” position.3)

Turn the ignition switch OFF.4)

Presets 1 2 3 4 5 6

A

B

C

6. TOOLS REQUIRED:

1. Clean Rag 5. 3mm Flat Screwdriver 9. Torque Wrench 13. Fish Wire

2. Needle Nose Pliers 6. Panel Removal Tool 10. Drill 14. Center Punch Tool

3. T-20 Torx Head Driver 7. 10mm Socket Wrench 11. 5/16” Drill Bit

4. #1 Phillip’s Screwdriver 8. Side Cutters 12. 15/32” Drill Bit

Removal of OE rearview mirror.1)

For vehicle’s having OE rearview mirror with con-a)

nector attached to back of mirror, continue below,

step 1b. For vehicle’s containing OE rearview mir-

ror without connector attached to back of mirror,

proceed to step 1g on next page.

Disconnect 10-pin connector from back of mirror.b)

Harness will be tucked up into the headliner at a

later step.

Remove and discard wire harness cover, which isc)attached from mirror base to headliner.

Using a T-20 Torx head driver, loosen the screw ond)

the mirror mount. (Fig. 1)

Slide the mirror base off of the button on the wind-e)

shield. (Fig. 1)

Skip to step 2 on next page.f)

Fig. 1

Ensure the slack on the installed harness is removed before securing wire ties.•

The harness routing needs to be followed as described to avoid interferences.•

CAUTION!

8/20/2019 1TE34

3/24

Rev. 08-17-10



Insert the at end of a 4mm screwdriver intog)

the opening at the bottom of the mirror mount.

(Fig. 2)

Slide the screwdriver upward into the center ofh)

the mirror mount until resistance is felt. Apply a

small amount of additional upward force to lift a

locking spring in the mount.

While still applying upward pressure with thei)

screwdriver, grasp the mirror bracket and lift

the mirror up towards the headliner and off the

mirror mounting bracket.

Remove driver side kicking plate.2)

Pull up kicking plate to disengage the pawls.a)

(Fig. 3)

Remove kicking plate from body panel.b)

Remove driver side dash side nisher.3)

Remove clip.a) (Fig. 4)

Remove dash side nisher xing clips withb)

panel removal tool and then remove dash side

nisher. (Fig. 4)

Using panel removal tool, loosen driver side weather4)

strip and remove from top of A-pillar to scuff plateand from B-pillar. (Fig. 5)

Fig. 2

Fig. 3

Fig. 4

Clip

Fig. 5

8/20/2019 1TE34

4/24

Rev. 08-17-10



Remove driver side A-pillar trim.5)

Disengage front A-pillar xing metal clips witha)

panel removal tool, and then pull up front A-pillar

to remove the pawls. (Fig. 6)

Remove driver side sun-visor assembly.6)

Remove sun-visor cap (1) xing pawls with aa)

small at screwdriver (A) wrapped into a tape (B).(Fig. 7)

Remove sun-visor assembly Phillip’s xing screw.b)

Disconnect vanity mirror lamp harness connec-c)

tors and remove assembly.

Remove driver side sun-visor holder.7) (Fig. 8)

Remove sun-visor holding xing pawls with aa)

small at screwdriver (A) wrapped into a tape (B).(Fig. 8)

Remove sun-visor holder Phillip’s mounting screwb)

and remove holder.

Loosen front of driver side headliner by gentlyc)

pulling downward to disengage clips. Headliner

does not need to be fully removed. (Fig. 9)

Fig. 6

Fig. 7Sun Visor

Mount

Fig. 8Sun Visor

Clip Cover

Fig. 9

8/20/2019 1TE34

5/24

Rev. 08-17-10



Partially release lower clips from driver side rear8)

nisher by pulling outward on three lower clips.

(Fig. 10)

Partially remove trunk weather seal from rear plate9) and LH luggage side nisher. (Fig. 11)

Remove the following trunk components.10) (Fig. 12)

Trunk oor carpet.a)

Spare tire cover.b)

Trunk oor box cover (without spare tire).c)

Trunk oor box cover (with spare tire).d)

a

b

cd

Fig. 12Front of

Vehicle

Fig. 10

1 2

Clips

Front of

Vehicle

Fig. 11

Front of

Vehicle

8/20/2019 1TE34

6/24

Rev. 08-17-10



Remove luggage rear plate.11) (Fig. 13)

Disengage rear trunk lid emergency handle (1)a)

xing clip with panel removal tool (A).

Using panel removal tool, remove luggage rearb)

plate xing clips.

Grab rear plate from bottom with hands and liftc)

upward to disengage the xing pawls.

Fig. 13

Remove the following interior parts as shown in Fig. 14. (Refer to vehicle service manual)12)

Trunk nisher front.a)

Driver side trunk side nisher.b)

Driver side trunk side box assembly.c)

Fig. 14

b

c

a

8/20/2019 1TE34

7/24

Rev. 08-17-10



Remove passenger side license plate lamp in nu-13)

merical order shown. (Fig. 15)

Disconnect the license plate lamp connector.a)

Remove license plate lamp.b)

For vehicle’s without spare 10-pin OE mirror

connector in overhead, proceed to s tep 14.

For vehicle’s containing the spare 10-pin har-c)

ness used on the factory mirror, wrap 1 piece offoam tape around connector. (Fig. 16)

Using panel removal tool, tuck harness upd)

into the headliner toward driver side. En-

sure harness is not interfering with headliner.

(Fig. 16)

Install In-mirror RearView Monitor mirror.14)

Plug the harness connector into the back of thea)

In-mirror RearView Monitor mirror.

Slide the In-mirror RearView Monitor mir-b)

ror base over the button on the windshield.

(Fig. 17)

Using a T-20 Torx head driver, tighten the screwc)

on the mirror mount 1.5 - 2.0 Nm (1.3 ft - lbs).

(Fig. 17)

Wrap 1 piece of foam tape around harness andd)

using panel removal tool, tuck between head-

liner and roof above EC mirror. (Fig. 18)

Fig. 17

1.5 - 2.0 Nm

Fig. 18

Foam Tape

Fig. 15

Push

Rotate

Foam

Tape

Spare

HarnessHarness

Fig. 16

8/20/2019 1TE34

8/24

Rev. 08-17-10



If a wire cover was removed from the OE mir-e)

ror, discard OE wire cover and grab new wire

cover from kit contents.

Route the harness into the groove of the wiref)

cover and attach to the mirror mount. (Fig. 19)

Slide the forks on top of the wire cover, into theg)

headliner. (Fig. 19)

Grasp mirror and rotate downward. Check toh)

ensure wire cover sits ush against windshield.

(Fig. 20)

If there is a gap between the wire cover andi)

windshield, ensure there is enough harness

slack from the mirror to the headliner. Adjust if

necessary.

Wrap a piece of foam tape around harness at j)

center of sun visor and where the headliner

bends towards driver-side door. (Fig. 21)

Using panel removal tool, tuck the wire harnessk)

between the headliner and roof. (Fig. 21)

Route harness down driver-side A-pillar andl)

secure to existing vehicle harness with 3 wire

ties. (Fig. 22)

Fig. 21

Foam Tape

Fig. 22

Wire Tie

Fig. 20

Fig. 19

Wire Cover

8/20/2019 1TE34

9/24

Rev. 08-17-10



Fig. 23

Foam

Tape

Mirror

Harness

Wrap 2 pieces of foam tape around mirrorm)

harness (including red and black wires) and

tuck between vehicle body and center dash.

(Fig. 23)

Secure all mirror harness wires in footwell arean)

to existing vehicle harness with 2 wire ties. (Fig. 24)

Separateo) Red and Black wires from mirror

harness. Red and black wires will be used at a

later step in the installation. (Fig. 25)

Secure mirror harness (p) without Red and Black

wires) to existing vehicle harness with 1 wire

tie. (Fig. 25)

Route harness to rear gate.15)

Secure harness to the inside of the vehiclea)body with 5 pieces of foam tape, below existing

vehicle harness in scuff plate area, from A-pillar

to B-pillar. (Fig. 26)

Fig. 24

Wire Tie

Fig. 25

Wire Tie

Red and

Black WiresHarness

Fig. 26

Foam Tape Vehicle

Front

8/20/2019 1TE34

10/24

Rev. 08-17-10



Secure harness to inside of the lower B-pillarb)

body with 2 pieces of foam tape. Ensure the

harness is routed so that the panel clip holes in

the body are not obstructed otherwise damage

to harness may occur. (Fig. 27)

By accessing opening in driver side trunk com-c)

partment, route sh wire (or equivalent) into thecovertible compartment. Be sure to leave a

portion of the sh wire in the trunk compartment

for future use. (Fig. 28)

Operate convertible top until rear convertibled)

lid is in the upright position and that the rear

convertible top is in the upright position, gain-

ing access to the convertible compartment.(Fig. 29)

Ensure engine is running when operating convertible top to prevent draining of vehicle battery.•

Operating convertible top excessively can cause an auto shut down, preventing operation of convertible•

top. Refer to owner’s manual for details.

CAUTION!

Fig. 29

Convertible

Lid

Convertible

Top

Fig. 27Foam Tape

Clip

Vehicle

Front

Fig. 28

Fish Wire

Opening in Rear

Compartment

Speaker

Vehicle

Front

8/20/2019 1TE34

11/24

Rev. 08-17-10



In order to gain access to covertible compart-e)

ment, vehicle liner (inside convertible lid) will

need to be pulled back slightly. (Fig. 30)

Route harness from inside driver’s compart-f)

ment into convertible compartment. Ensureharness is routed under vehicle bracket.

(Fig. 31)

Continue routing harness to the sh wire previ-g)

ously routed into convertible compartment.

Attach sh wire (or equivalent) to harness end.h)

(Fig. 32)

Completely close convertible top.i)

Open trunk compartment door. j)

Pull sh wire, with harness, into trunk compart-k)

ment. (Fig. 33)

Fig. 32

Fig. 31

Harness

Bracket

Vehicle

Front

Fig. 30

Vehicle Liner

Convertible

LidConvertible

Top

Fig. 33

Fish Wire

Harness

Opening in Rear

Compartment

Speaker

Vehicle

Front

8/20/2019 1TE34

12/24

Rev. 08-17-10



Continue routing harness along side existingl)

vehicle harness to rear of trunk, and towards

passenger side. Be sure to route harness un-

der vehicle bracket. (Fig. 34)

Remove sh wire from harness.m)

Establish location to attach camera bracket to ve-16)

hicle body.

Have a center punch tool readily available.a)

Ensure correct orientation of camera is estab-b)

lished as per illustration. (Fig. 35)

Place camera bracket onto rear of vehicle, nearc)

passenger side license plate light opening and

rear gate request switch. (Fig. 35)

Ensure camera bracket is pushed inward andd)

toward the driver side of the trim to ensure the

bracket is ush against “pocket” (a portion ofthe bracket has been removed from the illustra-

tion to better depict the necessary information).

(Fig. 36)

While camera bracket is still positioned ushe)

against the “pocket”, use a center punch tool to

mark the two outer holes. (Fig. 37)

Using center punch tool, mark the centerf)

hole just below the curvature of the opening.

(Fig. 37)

Fig. 35CameraBracket

Rear Gate

RequestSwitch

Passenger Side

License Plate

Light Opening

License

Plate Light

Opening

Rear Gate

Request

Switch

Fig. 36

Pocket

Camera

Bracket

Fig. 37CameraBracket

Pocket

Outer

Hole

Outer

HoleCenter

Hole

Fig. 34

Video

CableVehicle

Bracket Front of

Vehicle

Spare

Tire

8/20/2019 1TE34

13/24

Rev. 08-17-10



Drill out camera mounting holes.17)

Remove camera bracket from vehicle body.a)

Protect rear of vehicle body with tape or shopb)

towel before proceeding to next step.

Using a drill and a 5/16” drill bit, drill out the twoc)

outer locating holes. (Fig. 38)

Using a drill and a 15/32” drill bit, drill out thed) center locating hole. (Fig. 39)

Insert a well nut into the two outer holes untile)

the head of the nut is pressed up against the

plastic trim. (Fig. 40)

Attach camera to camera bracket.18)

Orient camera and camera bracket as shown.a)

Note locations of access hole, camera labeland camera cable. (Fig. 41)

Fig. 38

5/16”

Hole

Fig. 40

Well Nut

Fig. 39

15/32”

Hole

Fig. 41

Camera Label

(Bottom of

Camera)

Access

Hole

Camera

Cable

8/20/2019 1TE34

14/24

Rev. 08-17-10



Attach camera onto camera bracket and secureb)

using (2) M3 x 6mm Phillip’s screws (smaller

screws) as shown. Note access hole in order

to secure one of the camera screws. (Fig. 42)

Attach camera bracket to vehicle body.19)

Insert camera harness through center hole en-a)

suring harness is routed downward toward the

bumper. (Fig. 43)

Ensure correct orientation of camera andb)

camera bracket are identied and place bracket

onto vehicle body. (Fig. 43)

Ensure camera bracket is ush against “pocket”c)

(refer to fgure 36 for reference).

Insert (2) M4-0.7 X 12MM well nut screwsd)

(larger screws) into locating holes and loosely

secure using a Phillips screwdriver in a uniform

manner. If a uniform manner is not followedwhen loosely securing screws, difculty could

arise when trying to install screws. (Fig. 44)

Now securely tighten screws using Phillipse)

screwdriver.

Route camera harness toward bottom of ve-f)

hicle bumper area. (Fig. 45)

Fig. 43

Camera

Harness

Center

Hole

Fig. 44

Well Nut

Screw

Camera

Bracket

Fig. 42

Camera

Screw

Hole

Access

HolePhillips

Screwdriver

Fig. 45

Camera

Harness

Rear Gate Request

SwitchPassenger SideLicense Plate

Light Opening

8/20/2019 1TE34

15/24

Rev. 08-17-10



Locate vehicle grommet at rear trunk compartment20)

on passenger side.

Pull grommet outward, disengaging from ve-a)

hicle body. (Fig. 46)

Cut rear grommmet to allow for routing of camera21)

harness.

Using side cutters, cut a slit in the grommeta) approximately 8.5 mm in length on the bottom

side. Once complete, cut a small triangular

portion (approximately 4.5 mm in diameter) out

of the grommet to allow for the camera har-

ness. (Fig. 47)

Route mirror harness through passenger sideb)

grommet and to the bottom of the vehicle nearbumper area. (Fig. 48)

Locate both the camera connector and mirrorc)

harness connector. (Fig. 49)

Remove black electrical tape and tubing fromd)

mirror harness end, exposing connector, inorder to connect harness to camera harness.

Route camera harness connector to mirror har-e)

ness connector and connect. (Fig. 49)

Fig. 47

Slit in

Grommet

8.5mm

Fig. 49

Camera

Harness

Connector

Mirror Harness

Connector

Fig. 46Grommet

Front of

Vehicle

Spare

Tire

Fig. 48

Mirror

Harness

Front of

Vehicle

SpareTire

Rear

Bumper

8/20/2019 1TE34

16/24

Rev. 08-17-10



Pull mirror harness, with camera harness,f)

through passenger side grommet and into ve-

hicle trunk compartment. (Fig. 50)

Ensure excess slack of camera harness isg)

pulled into the vehicle compartment.

Open engine hood.22)

Disconnect negative battery terminal.a)

Secure gray end of the wire tap to larger23) Orange

Wire in fuse panel area in driver side kick panel area.

(Fig. 51)

See steps 24 - 28 for wire tap installation in-a)

structions.

Red mirror harness wire will be used as the ac-b) cessory wire.

Tap vehicle wire24) . (Fig. 52)

Remove cap (slot side) from tap body.a)

Slide the cap around vehicle wire.b)

Tighten the tapc) TIGHT with nger pressure.

NOTE:

Do not re-use the tap for subsequent re-instal-

lation.

Fig. 52

a) c)

b)

Fig. 50

Mirror Harness

Camera Harness

Front of

Vehicle

MA01

MA01

Orange

OrangeGreenBlackRed

Fig. 51

8/20/2019 1TE34

17/24

Rev. 08-17-10



Inspect the tap to ensure correct installation.25)

(Fig. 53)

NOTE:

Avo id putt ing pressure on the vehicle wire and

tap for the rest of the installation.

Tap accessory wire26) . (Fig. 54)

Remove tap (non-pierce) side from tap.a)

Remove the protective stub.b) Insert wire through the non-pierce side open-c)

ing.

Spread the individual strands into fan shape.d)

Insert wire into the tap body and ensure that ite)

is all the way in.

Tighten the tapf) TIGHT with nger pressure.

Conrm the tapped accessory wire.27) (Fig. 55)

Inspect the tap to ensure correct installation.a)

Test the signal to ensure that it is workingb)properly.

NOTE:

Avo id putt ing pressure on the vehicle wire, tap,

and accessory wire for the rest of the installa-

tion.

Secure the tap.28) (Fig. 56)

Secure the tapped wire on the non-pierce sidea)

to the body of the posi-tap with electrical tape

(2 revolutions).

Secure the body to harness where vehicle wireb)

is being tapped with electrical tape (2 revolu-

tions).

Fig. 53

i Straight and evenly spaced all the way around

ii. Tight and minimize gap (wire jacket should be crushed)

Fig. 54

c)

c) Insert wire to here

f) Tighten

d)

a)

Fig. 55

i. Straight and evenly spaced all around

ii. Tight and no gap

iii. Test the signal

Fig. 56

b)a)

Existing

Harness Accessory

Harness

8/20/2019 1TE34

18/24

Rev. 08-17-10



Locate the 10mm ground bolt in driver side cowl29)

area (behind carpet) and remove. (Fig. 57)

Install ring terminal from Black wire of mir-a)

ror harness over ground bolt and reinstall.

(Fig. 57)

Ensure ground bolt is tightened to 5.9 - 8.0 Nm.b)

Bundle excess Red and Black harness wiresc)

and secure, along with mirror harness, to exist-

ing vehicle harness with 1 wire tie. (Fig. 57)

Locate vehicle grommet at rear in trunk compart-30)ment on driver side. (Fig. 58)

If present, carefully remove electrical tape froma)

existing vehicle harness to expose electricalwires. (Fig. 59)

Fig. 57

Wire Tie

Excess

Wire

Ground

Bolt

Do not use sharp objects or objects that can damage electrical wires on next step. Plastic panel tool is•

acceptable.

CAUTION!

Fig. 59ElectricalTape

Fig. 58VehicleGrommet

Front of

Vehicle

Spare

Tire

8/20/2019 1TE34

19/24

Rev. 08-17-10



Secure Green harness wire to existing vehicle re-31)

verse circuit.

Locatea) Tan Wire in existing wire bundle at

driver side rear trunk compartment. (Fig. 60)

See steps 24 - 28, pages 16 - 17 for wire tapb)

installation instructions.

Green mirror harness wire will be used as thec)

accessory wire.

Verify a clear image is displayed on the monitor.32)

Reconnect negative battery cable.a)

Turn the ignition switch to ON.b)

With your foot on the brake pedal, move thec)

gear selector lever into reverse.

A clear image should display in the left handd)

side of the mirror. (Fig. 61)

Move the gear selector lever back into park.e)

The image should now disappear.

Turn the ignition switch to OFF.f)

Secure camera harness.33)

In trunk compartment, wrap a piece of butyla)

gum around camera harness at the point wherethe harness lines up to the vehicle grommet.

(Fig. 62)

Fig. 60

Tan Wire

Apply butyl gum to prevent potential leaks.•

CAUTION!

Fig. 61

I M A G E

Fig. 62

Butyl GumSlit in

Grommet

Front of

Vehicle

8/20/2019 1TE34

20/24

Rev. 08-17-10



Re-install vehicle grommet to body, ensuringb)

the slit in the grommet is facing downward.

(Fig. 63)

To ensure water integrity, conrm that the grom-c)

met is installed properly duirng re-installation.

Operate convertible top until rear convertibled)

lid and rear of convertible top are in the upright

position, gaining access to the convertible com-partment. (Fig. 64)

In order to gain access to covertible compart-e)

ment, vehicle liner (inside convertible lid) will

need to be pulled back slightly. (Fig. 65)

Ensure engine is running when operating convertible top to prevent draining of the vehicle battery.•

Operating convertible top excessively can cause an auto shut down, preventing operation of convertible•

top. Refer to owner’s manual for details.

CAUTION!

Fig. 64

Convertible

Lid

Convertible

Top

Fig. 63

Butyl Gum

Spare Tire

Front of

Vehicle

Fig. 65

Vehicle Liner

Convertible

LidConvertible

Top

8/20/2019 1TE34

21/24

Rev. 08-17-10



Secure harness to existing vehicle harness inf)

convertible area with 2 pieces of foam tape.

Ensure harness is routed under vehicle brack-

et. (Fig. 66)

Secure harness to vehicle body in convertibleg)

area with 1 piece of foam tape. (Fig. 67)

Completely close convertible top.h)

Open trunk compartment door.i)

Secure harness to existing vehicle harness j)

in trunk compartment area with 2 wire ties.

(Fig. 68)

Secure harness to existing vehicle harnessk)


(Fig. 69)

Fig. 66

Foam

Tape

BracketFront of

Vehicle

Fig. 67

Foam

Tape

Front of

Vehicle

Fig. 69

Wire Tie

Front of

Vehicle

Rear

Speaker

Spare Tire

Fig. 68

Wire Tie

Front of

Vehicle

Rear

Speaker

8/20/2019 1TE34

22/24

Rev. 08-17-10



Secure camera harness and mirror harness tol)

existing vehicle harness in trunk compartment

area with 2 wire ties. (Fig. 70)

Secure harness to existing vehicle harnessm)


(Fig. 71)

Bundle excess mirror harness and secure to ex-n)

isting vehicle harness with 2 wire ties. (Fig. 71)

Testing34)

Reconnect the vehicle’s negative battery cablea)

(if not already connected).

Tighten negative battery terminal nut to 4.1 Nm.b)

Turn the ignition switch to ON.c)

Ensure vehicle is in a failure well lit area.d)

Check to see that the green LED is illuminated.e)

If it is not, press the “ “ button to turn it on.

Cover the forward-looking photocell (located tof)the driver side of the wire harness connection

on the back of the mirror) with a dark cloth or

towel. After a few seconds, the mirror should

begin to darken. Timing will vary with ambient

light levels and a ashlight may be shined on

the rearward photocell if needed, to accelerate

effect.

Remove the cover from the forward-lookingg)

photocell and the mirror will begin to clear.

Push the “ “ button to ensure compass dis-h)

play shows either a direction such as “NE” or a

“C”, and that it can be turned ON and OFF.

Push each Homelink® button one at a timei)and verify that the LED indicator to the left of

the center switch illuminates with a red LED.

(Fig. 73)

Re-install the remaining components, referring to the35)

service manual for the vehicle

Clean interior of vehicle.36)

Fig. 73

Red LED

Homelink Buttons

NE

Fig. 72

Rearward

PhotocellGreen LED

Dark Cloth or

Towel

Compass Display

Fig. 70

Wire TieSpare Tire

Front of

Vehicle

Fig. 71

Wire Tie

Excess MirrorHarness

Spare Tire

Front of

Vehicle

8/20/2019 1TE34

23/24

Rev. 08-17-10



Set Compass Zone37)

With the display turned “ON”, push the “ “a)

button for 3 seconds, until a number appears

in display (numbers correspond to regional

compass zones).

Press and release “ “ button to scroll throughb)

zone numbers.

Release “ “ button when correct zonec)

number is displayed. Zone number will disap-

pear and display will return to showing either adirectional heading or a “C” after 5 seconds of

no switch activity.

Calibrate Compass38)

Drive vehicle in circles (360°) at 5 mph or lessa)

until compass display window shows a direc-

tion.

CAUTION

Use caution when re-installing interior components to avoid damage, scratches, or breaking of mounting•

clips. Refer to the vehicle specic service manual for more information.

Trim pieces found to have witness marks or broken clips are not to be reinstalled.•

!

1

2

3

4

5

67 8

9

10

11

12

13

14

152

3

4

5

6 78 9 10 11

1213

14

Fig. 74

9. Post Installation Check Sheet

Inspect the vehicle interior and exterior for damage.

Ensure all trim panels are fully seated properly.

Conrm trunk / cargo light.

Conrm proper operation of vehicle systems.

Reset radio presets to the recorded settings.

Conrm driver side speaker in driver side rear panel (if equipped).

Conrm back up lamps.

Conrm proper sunroof operation and perform the reset procedure if necessary.

Conrm license plate lights.

Place the User Guide in the glove box.

Check the trim for proper ush t after re-installing the interior components.

Posi-Tap™ is protected by patent # 5,228,875 5,695,369 5,868,589 6,692,313 Jap 2881414 Aus 708700

Tia 103534 Can 2204826 Mex 200626 Korea 477279 China Z197105562.9 & others pending.

8/20/2019 1TE34

24/24


The grey area indicated

must be included in the

display

Bold lines indicate the

actual eld of vision.

Vehicle width both

sides 200 mm

300 mm

5,000 mm

B A: 300 mm max.

B: 5,000 mm min.

A

Verify the camera is operating properly.

Camera should meet the below performance requirements.

Verify In-mirror RearView Monitor has the correct amount of rear bumper present. Cut out the“Go-No-Go” gauge below and place on mirror display (dimensions of cut out must be measured prior tocutting to ensure accuracy of printer).

Bumper Visual = Not Acceptable

Bumper Visual = Acceptable

44mm

71mm

1TE34

Documents