-
CHAPTER 1. SPECIFICATIONS[1]
SPECIFICATIONS.................................................1-1
CHAPTER 2. IMPORTANT SERVICE NOTES[1] IMPORTANT SERVICE NOTE
..............................2-1
CHAPTER 3. ADJUSTMENT PRECAUTIONS[1] ADJUSTMENT PRECAUTIONS
...........................3-1[2] ADJUSTMENT
......................................................3-15
CHAPTER 4. TROUBLE SHOOTING FLOWCHART[1] TROUBLE SHOOTING
FLOWCHART..................4-1
CHAPTER 5. SOLID STATE DEVICE BASE DIAGRAM[1] SOLID STATE DEVICE
BASE DIAGRAM.............5-1
CHAPTER 6. CHASSIS LAYOUT[1] CHASSIS
LAYOUT................................................6-1
CHAPTER 7. DESCRIPTION OF SCHEMATIC DIAGRAM[1] DESCRIPTION OF
SCHEMATIC DIAGRAM ........7-1
CHAPTER 8. BLOCK DIAGRAM[1] BLOCK DIAGRAM : MAIN UNIT
...........................8-1
CHAPTER 9. WAVEFORM[1]
WAVEFORM..........................................................9-1
CHAPTER 10. SCHEMATIC DIAGRAM[1] SCHEMATIC DIAGRAM : CRT UNIT
....................10-1[2] SCHEMATIC DIAGRAM : MAIN UNIT
..................10-2
CHAPTER 11. PRINTED WIRING BOARD ASSEMBLIES[1] PWB-A : MAIN UNIT
.............................................11-1[2] PWB-B : CRT
UNIT...............................................11-5
NTSC System 125-CH Program Memory AV Mode
(Standard/Dynamic/Soft) CATV Hyper Band Ready 4 Line Digital Comb
Filter Blue/Black Stretch Circuit Picture Noise Reduction White
Temp. Select Aperture Control Gamma Correction Dual Language OSD
(English/Spanish) Demo Selectable Audio Output - FAO/VAO Close
Caption
SERVICE MANUAL29L-FG1L
COLOUR TELEVISIONChassis No. GB-5
MODEL
CONTENTS
WARNINGThe chassis in this receiver is partially hot. Use an
isolation transformer between the line cord plug andpower
receptacle, when servicing this chassis. To prevent electric shock,
do not remove cover. No user -serviceable parts inside. Refer
servicing to qualified service personnel.
29L-FG1LIn the interests of user safety (Required by safety
regulations in some countries) the set should be restored to its
original condition and only parts indentical to those specified
should be used.
On/Off/Reminder Timer (with beep sound) Rear AV-IN 1, AV Output
(Monitor Out), Headphone
and Front AV-IN 2 Power Save AFT Component Input Terminal (share
with AV1) MTS Stereo Decoder Child Lock Graphic Equalizer Sound
Mode (Music/Movie/News/Custom) Hotel Mode EZ Setup 16 : 9 Mode
S677529LFG1L
Parts Guide
1st Edition
-
29L-FG1L
1 1
TV29L-FG1LService Manual29L-FG1LMarketE CHAPTER 1.
SPECIFICATIONS
[1] SPECIFICATIONS
SPECIFICATIONS
Focus
.....................................................................
Bi-Potential, Uni-Potential ElectrostaticSweep Deflection
...................................................................................................
Magnetic
Intermediate FrequenciesPicture IF Carrier
................................................................................................
38.9MHzSound IF Carrier
Colour Sub-Carrier
Power Input
...................................................................................
110 ~ 220V AC 50/60 HzPower Consumption
.....................................................................................................
138W
Audio Power Output Rating
......................................................................
7.5W x 2 (at Max.)
SpeakerSize
...........................................................................................................
8 cm round x 2
Aerial Input ImpedanceVHF/UHF
.........................................................................................
75 ohms Unbalanced
Receiving ChannelsVHF
................................................................................................................
2 thru 13UHF
..............................................................................................................
14 thru 69CATV
..................................................................................................................
1 thru 125
Digital Terrestrial Broadcast (VHF/UHF)
............................................................ 2 thru
69(EIA, Channel Plan U.S.A.)
Receiving Frequency
................................................................
55.25 MHz thru 801.25 MHz
Dimensions
.....................................................................................................
Width: 810mmHeight: 618mmDepth: 516.5mm
Weight(approx): 41.0 kg
Cabinet material
..................................................................................................
All Plastics
Specifications are subject to change without prior notice.
Convergence
...............................................................................
Self Convergence System
................................................................................................
34.4MHz
................................................................................................
35.32MHz
-
29L-FG1L
2 1
TV29L-FG1LService Manual29L-FG1LMarketE CHAPTER 2. IMPORTANT
SERVICE NOTES
[1] IMPORTANT SERVICE NOTE
IMPORTANT SERVICE NOTES
Maintenance and repairing of this receiver should be done by
qualified service personnel only.
SERVICE OF HIGH VOLTAGE SYSTEM AND
PICTURE TUBEWhen servicing the high voltage system, remove
static charge from it by
connecting a 10K ohm resistor in series with an insulated wire
(such as a test
probe) between picture tube dag and 2nd anode lead. (AC line
cord should
be disconnected from AC outlet.)
1. Picture tube in this receiver employs integral implosion
protection.
2. Replace with the same type number of picture tube for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing shatterproof
goggles and after discharging
the high voltage completely.
X-RAYThis receiver is designed so that any X-Ray radiation is
kept to an absolute
minimum. Since certain malfunctions or servicing may produce
potentially
hazardous radiation with prolonged exposure at close range, the
following
precautions should be observed:
1. When repairing the circuit, please make sure do not increase
the high voltage of the set
to more then 34.0kV (at beam 0 A).
2. To keep the set in a normal operation, please make sure it's
function at 30.0kV 1.5kV
(at beam 1700 A). The set has been factory - adjusted to the
above-mentioned high voltage.
*If there is a possibility that the high voltage fluctuates as a
result of the repaires,
never forget to check for such high voltage after the work.
3. Do not substitute a picture tube with unauthorized types
and/or brands which may cause
excessive X-ray radiation.
BEFORE RETURNING THE RECEIVERBefore returning the receiver to
the user, perform the following safety checks.
1. Inspect all lead dress to make certain that leads are not
pinched or that hardware is not
lodged between the chassis and other metal parts in the
receiver.
2. Inspect all protective devices such as non-metal control
knobs, insulating fishpapers,
cabinet backs, adjustment and compartment covers or shields,
isolation resistor- ca-
pacity networks, mechanical insulators etc.
-
29L-FG1L
TV29L-FG1LService Manual29L-FG1LMarketE CHAPTER 3. ADJUSTMENT
PRECAUTIONS
[1] ADJUSTMENT PRECAUTIONS
ADJUSTMENT PRECAUTIONS
This model's setting are adjusted in two different ways: through
the I2C bus control and in the
conventional analog manner. The adjustments via the I2C bus
control include preset-only items and
variable data.
1. Setting the service mode by the microprocessor.
(1). Press and hold the local key "VOL DOWN" & "CH UP" when
power on the main switch,
TV will enter into the SERVICE MODE.(The initial value of EEPROM
are automatically
preset when new EEPROM is used)
(2). Press the CH DOWN / UP key on the remote controller to get
ready to select the mode
one by one.
(3). Press the CH DOWN / UP key on the remote controller to
select the modes reversibly
one by one.
(4). Using the VOLUME UP/ DOWN key on the remote controller, the
data can be modified.
(5). When press the local key "VOL DOWN" & "CH UP" at the
same time,
it will be released from the service mode.
2. Factory Presetting.
(1). After enter into the SERVICE MODE, at "INIT EEPROM" service
item (which is under
"CHECK MODE" section) press remote controller key of code "ED",
the initial
values are automatically preset.
(2). The initial data are preset as listed in page 4 to 12.
(3). Make sure whether the data need to modify or not (Initial
data).
Note: Once the chassis has been assembly together and in ready
condition, please make
sure it's go through initialize process (see sect 2-(1)
above)
Precaution: If haven't done this initialization, malfunction
might be happen.
3 1
-
29L-FG1L
1) In the Service Mode, key is use to select the mode in the
following order.
SETTING MODE 1
Picture
Setting
SETTING MODE 3
Audio
Setting
CHECK MODEOPTION MODE
Function Setting
MENU button
of R/C
MENU button
of R/C
MENU button
of R/C
MENU button
of R/C
ADJUSTMENT MODE
RF AGC50Hz/60Hz
GEOMETRIC ADJ
CUT OFF/
WHITE BALANCE ADJ
PICTURE
SUB ADJ
MENU button
of R/C
3 2
-
29L-FG1L
ADJUSTMENT MODE ITEMS SEQUENCE
Notes:
FORWARD : CH UP KEY
REVERSE : CH DOWN KEY
VX-43COMP-P60
EW-W-P60
E/W-PAR-P60
HOR-SHI-P60
VER-AMP-P60
DRI-BS-DVD
DRI-GS-DVD
SUB-TINT
SUB-SHARP
SUB-CON-DVD
SUB-TINT-DVD
SUB-BRI
SUB-BRI-DVD
SUB-COL
SUB-CON
DRI-RS-DVD
CUT-GW
DRI-GW
DRI-BW
CUT-RW
DRI-RW
CUT-RC
CUT-GC
DRI-GC
DRI-BC
CUT-GS
DRI-RC
DRI-RS
DRI-GS
CUT-RS
DRI-BS
S-COR
LOCOR-PAR
E/W-TRAP
V-SCROLL
VX-NORMAL
VER-SHI-F60
VER-AMP-F60
HOR-SHI-F60
CUT-RS-DVD
H-BOW
VER-SHI-P60
V-LIN
UPCOR-PAR
CUT-GS-DVD
DRI-RC-DVD
DRI-GC-DVD
DRI-BC-DVD
CUT-RC-DVD
CUT-GC-DVD
DRI-RW-DVD
DRI-GW-DVD
CUT-GW-DVD
DRI-BW-DVD
CUT-RW-DVD
V SLOPE
H-PAR
EW-W-F60
E/W-PAR-F60
GEOMETRIC
ADJ MODE
WHITE POINT
ADJ MODE
PICTURE SUB ADJ
MODE
3 3
-
29L-FG1L
OPTION MODE MENU
0001 Option Mode Picture Tube Used Type TUBE-TYPE
0002 PIF Frequency Setting PIF
0003 Sound M SND-M
0004 Sound DK SND-DK
0005 Sound I SND-I
0006 Sound BG SND-BG
0007 Colour System SECAM SECAM
0008 Colour System NTSC358 NTSC358
0009 Colour System NTSC443 NTSC443
0010 Audio Configuration AUDIO-CFG
0011 Mono Bilingual BILINGUAL
0012 Equalizer EQUALIZER
0013 Sub Woofer WOOFER
0014 Hotel Mode HOTEL
0015 Hotel Volume HTL-VOL
0016 Hotel Program Number HTL-PRG
0017 HTL-USE-LAST HTL-USE-LAST
0018 Childlock CHILD
0019 Wide Screen Signalling WSS
0020 Golden SCART GLD-SCART
0021 Power On Last Status PW-LAST
0022 AV1-IN AV1-IN
0023 Component Input DVD1-IN
0024 AV2-IN AV2-IN
0025 INCL-AV INCL-AV
0026 Reminder Timer TIM-REMINDER
0027 Off Timer TIM-OFF
0028 Commercial Skip Timer TIM-SKIP
0029 Virgin Mode VIRGIN MODE
0030 ERR-1-8-SUP ERR-1-8-SUP
0031 ERR-XRAY ERR-XRAY
0032 ERR-SUPVOL ERR-SUPVOL
0033 ERR-VERTG ERR-VERTG
0034 ARROW-ENTER-KEY ARROW-ENTER-KEY
0035 Teletext Pan-european TXTEURO-UNUSED
0036 Teletext Western TXTWEST-UNUSED
0037 Teletext On TXT ON-UNUSED
0038 Variable Audio Out VAO
0039 BASS-EFFECT BASS-EFFECT
0040 TB-EFF-NOT-USED TREBLE-EFFECT
0041 Spanish OSD Language SPANISH
0042
0043
0044
0
1
0
0
1
1
0
0
0
1
0
0
0
1
1
1
1
1
1
1
0
1
1
1
0
30
1
0
1
INITIAL DATA
1
1
0
1
1
1
1
2
0
0/1
0/1
0/1
0..7
0/1
0/1
0/1
0..2
0/1
0/1
0/1
0/1
0...60
0...99
0/1
0/1
0/1
0/1
1
0..2
0/1
0/1
0/1
0/1
0/1
0/1
0
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0
1
0
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0
0
30
0
2
0
1
0
1
1
0
1
1
1
1
0
0
1
0
0
0
0
ITEM SERVICE MODE EEPROM ITEM OSD
0/1
0/1
DATA SETTING DATA
1
2
1
1
1
1
0
1
1
1
0
1
1
1
0
0
0
0 1
IO-EXP-NOT-USED IO-EXP-NOT-USED 0/1 0 0
DEMO DEMO 0/1
1Close Caption CC 0/1 1
3 4
-
29L-FG1L
Adjustment Mode Items
ITEM EEPROM SETTING DATA RANGE IC OSD INITIAL DATA SETTING
DATA
A001 RF-AGC 063 UOC-TV RF-AGC 23 23
A002 V SLOPE 063 UOC-TV V SLOPE 35 35
A003 VER-SHI-F50 063 UOC-TV VER-SHI-F50 39 35
A004 VER-AMP-F50 063 UOC-TV VER-AMP-F50 35 31
A005 HOR-SHI-F50 063 UOC-TV HOR-SHI-F50 31 39
A006 EW-W-F50 063 UOC-TV EW-W-F50 11 28
A007 E/W-PAR-F50 063 UOC-TV E/W-PAR-F50 32 40
A008 H-PAR 063 UOC-TV H-PAR 30 30
A009 H-BOW 063 UOC-TV H-BOW 31 32
A010 UPCOR-PAR 063 UOC-TV UPCOR-PAR 40 43
A011 LOCOR-PAR 063 UOC-TV LOCOR-PAR 41 45
A012 E/W-TRAP 063 UOC-TV E/W-TRAP 32 26
A013 V-SCROLL 063 UOC-TV V-SCROLL 33 33
A014 VX-NORMAL 063 UOC-TV VX-NORMAL 25 25
A015 V-LIN 063 UOC-TV V-LIN 35 39
A016 S-COR 063 UOC-TV S-COR 32 32
A017 DRI-RS 063 UOC-TV DRI-RS 32 32
A018 DRI-GS 063 UOC-TV DRI-GS 32 32
A019 DRI-BS 063 UOC-TV DRI-BS 32 32
A020 CUT-RS 063 UOC-TV CUT-RS 32 32
A021 CUT-GS 063 UOC-TV CUT-GS 32 32
A022 SUB-BRI 063 UOC-TV SUB-BRI 34 34
A023 SUB-CON 063 UOC-TV SUB-CON 48 48
A024 SUB-COL 063 UOC-TV SUB-COL 10 26
A025 SUB-TINT 063 UOC-TV SUB-TINT 38 28
A026 SUB-SHARP 063 UOC-TV SUB-SHARP 32 32
A027 DRI-RS-DVD 063 UOC-TV DRI-RS-DVD 32 32
A028 DRI-GS-DVD 063 UOC-TV DRI-GS-DVD 32 32
A029 DRI-BS-DVD 063 UOC-TV DRI-BS-DVD 32 32
A030 CUT-RS-DVD 063 UOC-TV CUT-RS-DVD 32 32
A031 CUT-GS-DVD 063 UOC-TV CUT-GS-DVD 32 32
A032 SUB-BRI-DVD 063 UOC-TV SUB-BRI-DVD 35 35
A033 SUB-CON-DVD 063 UOC-TV SUB-CON-DVD 48 48
A034 SUB-TINT-DVD 063 UOC-TV SUB-TINT-DVD 32 32
A035 DRI-RC 063 UOC-TV DRI-RC 32 32
A036 DRI-GC 063 UOC-TV DRI-GC 32 32
A037 DRI-BC 063 UOC-TV DRI-BC 32 32
A038 CUT-RC 063 UOC-TV CUT-RC 32 32
A039 CUT-GC 063 UOC-TV CUT-GC 32 32
A040 DRI-RW 063 UOC-TV DRI-RW 32 32
A041 DRI-GW 063 UOC-TV DRI-GW 32 32
A042 DRI-BW 063 UOC-TV DRI-BW 32 32
A043 CUT-RW 063 UOC-TV CUT-RW 32 32
A044 CUT-GW 063 UOC-TV CUT-GW 32 32
A045 DRI-RC-DVD 063 UOC-TV DRI-RC-DVD 32 32
A046 DRI-GC-DVD 063 UOC-TV DRI-GC-DVD 32 32
A047 DRI-BC-DVD 063 UOC-TV DRI-BC-DVD 32 32
A048 CUT-RC-DVD 063 UOC-TV CUT-RC-DVD 32 32
A049 CUT-GC-DVD 063 UOC-TV CUT-GC-DVD 32 32
A050 DRI-RW-DVD 063 UOC-TV DRI-RW-DVD 32 32
A051 DRI-GW-DVD 063 UOC-TV DRI-GW-DVD 32 32
A052 DRI-BW-DVD 063 UOC-TV DRI-BW-DVD 32 32
A053 CUT-RW-DVD 063 UOC-TV CUT-RW-DVD 32 32
A054 CUT-GW-DVD 063 UOC-TV CUT-GW-DVD 32 32
A055 VER-SHI-N50 063 UOC-TV VER-SHI-N50 15 15
A056 VER-AMP-N50 063 UOC-TV VER-AMP-N50 28 28
A057 HOR-SHI-N50 063 UOC-TV HOR-SHI-N50 44 44
A058 EW-W-N50 063 UOC-TV EW-W-N50 29 29
3 5
-
29L-FG1L
ITEM EEPROM SETTING DATA RANGE IC OSD INITIAL DATA SETTING
DATA
A059 E/W-PAR-N50 063 UOC-TV E/WPAR-N50 25 25
A060 VER-SHI-S50 063 UOC-TV VER-SHI-S50 13 13
A061 VER-AMP-S50 063 UOC-TV VER-AMP-S50 22 22
A062 HOR-SHI-S50 063 UOC-TV HOR-SHI-S50 44 44
A063 EW-W-S50 063 UOC-TV EW-W-S50 29 29
A064 E/W-PAR-S50 063 UOC-TV E/W-PAR-S50 22 22
A065 SUB-SCROLL-S 063 UOC-TV SUB-SCROLL-S 31 31
A066* SUB-VX-S50 063 UOC-TV SUB-VX-S50 43 43
A066** SUB-VX-S50-NIL 0 UOC-TV SUB-VX-S50-NIL 0 0
A067 VER-SHI-C50 063 UOC-TV VER-SHI-C50 14 14
A068 VER-AMP-C50 063 UOC-TV VER-AMP-C50 23 23
A069 HOR-SHI-C50 063 UOC-TV HOR-SHI-C50 44 44
A070 EW-W-C50 063 UOC-TV EW-W-C50 29 29
A071 E/W-PAR-C50 063 UOC-TV E/W-PAR-C50 22 22
A072 SUB-SCROLL-C 063 UOC-TV SUB-SCROLL-C 31 31
A073* SUB-VX-C50 063 UOC-TV SUB-VX-C50 49 49
A073** SUB-VX-C50-NIL 0 UOC-TV SUB-VX-C50-NIL 0 0
A074 VER-SHI-P50 063 UOC-TV VER-SHI-P50 39 35
A075 VER-AMP-P50 063 UOC-TV VER-AMP-P50 35 31
A076 HOR-SHI-P50 063 UOC-TV HOR-SHI-P50 31 39
A077 EW-W-P50 063 UOC-TV EW-W-P50 11 28
A078 E/W-PAR-P50 063 UOC-TV E/W-PAR-P50 32 40
A079 VX-43COMP-P50 063 UOC-TV VX-43COMP-P50 5 5
A080 VER-SHI-F60 063 UOC-TV VER-SHI-F60 36 34
A081 VER-AMP-F60 063 UOC-TV VER-AMP-F60 37 33
A082 HOR-SHI-F60 063 UOC-TV HOR-SHI-F60 37 46
A083 EW-W-F60 063 UOC-TV EW-W-F60 10 27
A084 E/W-PAR-F60 063 UOC-TV E/W-PAR-F60 34 41
A085 VER-SHI-N60 063 UOC-TV VER-SHI-N60 13 13
A086 VER-AMP-N60 063 UOC-TV VER-AMP-N60 29 29
A087 HOR-SHI-N60 063 UOC-TV HOR-SHI-N60 46 46
A088 EW-W-N60 063 UOC-TV EW-W-N60 29 29
A089 E/W-PAR-N60 063 UOC-TV E/W-PAR-N60 22 22
A090 VER-SHI-S60 063 UOC-TV VER-SHI-S60 12 12
A091 VER-AMP-S60 063 UOC-TV VER-AMP-S60 20 20
A092 HOR-SHI-S60 063 UOC-TV HOR-SHI-S60 52 52
A093 EW-W-S60 063 UOC-TV EW-W-S60 28 28
A094 E/W-PAR-S60 063 UOC-TV E/W-PAR-S60 22 22
A095* SUB-VX-S60 063 UOC-TV SUB-VX-S60 45 45
A095** SUB-VX-S60-NIL 0 UOC-TV SUB-VX-S60-NIL 0 0
A096 VER-SHI-C60 063 UOC-TV VER-SHI-C60 11 11
A097 VER-AMP-C60 063 UOC-TV VER-AMP-C60 20 20
A098 HOR-SHI-C60 063 UOC-TV HOR-SHI-C60 51 51
A099 EW-W-C60 063 UOC-TV EW-W-C60 29 29
A100 E/W-PAR-C60 063 UOC-TV E/W-PAR-C60 22 22
A101* SUB-VX-C60 063 UOC-TV SUB-VX-C60 51 51
A101** SUB-VX-C60-NIL 0 UOC-TV SUB-VX-C60-NIL 0 0
A102 VER-SHI-P60 063 UOC-TV VER-SHI-P60 36 34
A103 VER-AMP-P60 063 UOC-TV VER-AMP-P60 37 33
A104 HOR-SHI-P60 063 UOC-TV HOR-SHI-P60 37 46
A105 EW-W-P60 063 UOC-TV EW-W-P60 10 27
A106 E/W-PAR-P60 063 UOC-TV E/W-PAR-P60 30 41
A107 VX-43COMP-P60 063 UOC-TV VX-43COMP-P60 5 5
A108 VSD 0/1 UOC-TV VSD 0 0
A109 CUT OFF 063 UOC-TV CUT OFF 11 *1
A110 VG2 0/1 UOC-TV VG2 0 0
A111 DCXO 0127 UOC-SSD DCXO 57 76
A112 DCXO-AUTO 0/1 UOC-SSD DCXO-AUTO 0 0
NOTE : (A--- * ) - Data for 29L-FG1MX ; (A--- ** ) - Data for
29L-FG1L
SETTING DATA CUT OFF FOR DIFFERENT CRT
SETTING
DATA LG CRT MTPD CRT
*1 A109 15 13CUT OFF
ITEMEEPROM SETTING DATA
SETTING
3 6
-
29L-FG1L
Setting Mode 1 Items
ITEM IC INITIAL DATA SETTING DATA
S001 UOC-TV 0 0
S002 UOC-TV 32 32
S003 UOC-TV 1 3
S004 UOC-TV 12 14
S005 UOC-TV 1 0
S006 UOC-TV 1 1
S007 UOC-TV 0 0
S008 UOC-TV 0 0
S009 UOC-TV 11 11
S010 UOC-TV 11 11
S011 UOC-TV 9 9
S012 UOC-TV 7 7
S013 UOC-TV 7 7
S014 UOC-TV 7 7
S015 UOC-TV 7 7
S016 UOC-TV 7 7
S017 UOC-TV 7 7
S018 UOC-TV 7 7
S019 UOC-TV 7 7
S020 UOC-TV 7 7
S021 UOC-TV 7 7
S022 UOC-TV 7 7
S023 UOC-TV 7 7
S024 UOC-TV 7 7
S025 UOC-TV 1 1
S026 UOC-TV 1 1
S027 UOC-TV 0 0
S028 UOC-TV 1 1
S029 UOC-TV 1 1
S030 UOC-TV 1 1
S031* UOC-TV 1 1
S031** UOC-TV 0 0
S032 UOC-TV 1 1
S033 UOC-TV 0 0
S034 UOC-TV 1 1
S035 UOC-TV 7 7
S036 UOC-TV 1 1
S037 UOC-TV 1 1
S038 UOC-TV 0 0
S039 UOC-TV 1 1
S040 UOC-TV 1 0
S041 UOC-TV 1 0
S042 UOC-TV 1 0
NOTE : (S031* ) - Data for 29L-FG1MX ; (S031**) - Data for
29L-FG1L
WHITE LMT 015 WHITE LMT
063 IFPLL
03 SOC1-0
DATA RANGE OSD
02 V-LINCTRL
EEPROM SETTING
V-LINCTRL
IFPLL
SOC1-0
GD 0/1 GD
AGC0-1 03 AGC0-1
FFI 0/1 FFI
CFA0 0/1 CFA0
YD PAL 015 YD PAL
YD SECAM 015 YD SECAM
YD N358 015 YD N358
YD N443 015 YD N443
YD AV-PAL 015 YD AV-PAL
YD AV-SECAM 015 YD AV-SECAM
YD AV-N358 015 YD AV-N358
YD AV-N443 015 YD AV-N443
YD SAV-PAL 015 YD SAV-PAL
YD SAV-SECAM 015 YD SAV-SECAM
YD SAV-N358 015 YD SAV-N358
YD SAV-N443 015 YD SAV-N443
YD COMP-PAL 015 YD COMP-PAL
YD COMP-SECAM 015 YD COMP-SECAM
YD COMP-N358 015 YD COMP-N358
YD COMP-N443 015 YD COMP-N443
SBO1-0 03 SBO1-0
CHSE1-0 03 CHSE1-0
FCO 0/1 FCO
OSO 0/1 OSO
DFL 0/1 DFL
EVG 0/1 EVG
HCO 0/1 HCO
SVMA 0/1 SVMA
HCO-NIL 0 HCO-NIL
FBC 0/1 FBC
SLG1-0 03 SLG1-0
CL3-0 015 CL3-0
GAM 0/1 GAM
TFR 0/1 TFR
CLD 0/1 CLD
BKS 0/1 BKS
BSD 0/1 BSD
AAS1-0 03 AAS1-0
DSK-NOT-PAL-AV 0/1 DSK-NOT-PAL-AV
3 7
-
29L-FG1L
ITEM IC INITIAL DATA SETTING DATA
S043 UOC-TV 0 1
S044 UOC-TV 0 0
S045 UOC-TV 1 0
S046 UOC-TV 0 0
S047 UOC-TV 3 2
S048 UOC-TV 1 3
S049 UOC-TV 0 0
S050 UOC-TV 2 2
S051 UOC-TV 5 5
S052 UOC-TV 3 0
S053 UOC-TV 0 1
S054 UOC-TV 0 0
S055 UOC-TV 0 0
S056 UOC-TV 1 1
S057 UOC-TV 0 0
S058 UOC-TV 1 1
S059 UOC-TV 3 3
S060 UOC-TV 45 32
S061 UOC-TV 46 *4
S062 UOC-TV 45 *5
S063 UOC-TV 40 31
S064 UOC-TV 31 31
S065 UOC-TV 31 31
S066 UOC-TV 46 31
S067 UOC-TV 23 23
S068 UOC-TV 49 43
S069 UOC-TV 35 43
S070 UOC-TV 35 35
S071 UOC-TV 31 31
S072 UOC-TV 31 31
S073 UOC-TV 40 40
S074 UOC-TV 31 34
S075 UOC-TV 34 *6
S076 UOC-TV 32 34
S077 UOC-TV 31 30
S078 UOC-TV 32 32
S079 UOC-TV 0 0
S080 UOC-TV 1 1
S081 UOC-TV 1 1
S082 UOC-TV 1 1
S083 UOC-TV 3 3
S084 UOC-TV 1 1
BLS 0/1 BLS
EEPROM SETTING DATA RANGE OSD
LLB 0/1 LLB
DSA 0/1 DSA
RPA1-0 02 RPA1-0
RPO1-0 03 RPO1-0
COR1-0 03 COR1-0
CRA0 0/1 CRA0
SPR2-0 06 SPR2-0
SVM2-0-PAL 07 SVM2-0-PAL
SMD1-0 03 SMD1-0
PEAKFREQPAL443 03 PEAKFREQPAL443
PEAKFREQPALM 03 PEAKFREQPALM
PEAKFREQPALN 03 PEAKFREQPALN
PEAKFREQNTSC443 03 PEAKFREQNTSC443
PEAKFREQNTSCM 03 PEAKFREQNTSCM
PEAKFREQSECAM 03 PEAKFREQSECAM
PEAKFREQDVD 03 PEAKFREQDVD
OF-COL-TV 03162 OF-COL-TV
OF-COL-AV 03162 OF-COL-AV
OF-COL-DVD 03162 OF-COL-DVD
OF-COL-P 03162 OF-COL-P
OF-COL-S 03162 OF-COL-S
OF-COL-N4 03162 OF-COL-N4
OF-COL-N3 03162 OF-COL-N3
OF-SHP-TV 03162 OF-SHP-TV
OF-SHP-AV 03162 OF-SHP-AV
OF-SHP-DVD 03162 OF-SHP-DVD
OF-SHP-P 03162 OF-SHP-P
OF-SHP-S 03162 OF-SHP-S
OF-SHP-N4 03162 OF-SHP-N4
OF-SHP-N3 03162 OF-SHP-N3
OF-TINT-TV 03162 OF-TINT-TV
OF-TINT-AV 03162 OF-TINT-AV
OF-TINT-DVD 03162 OF-TINT-DVD
OF-TINT-ADJ 03162 OF-TINT-ADJ
BB-TINT 063 BB-TINT
VMA-SOFT 03 VMA-SOFT
WS-SOFT 03 WS-SOFT
VMA-STD 03 VMA-STD
WS-STD 03 WS-STD
VMA-DYN 03 VMA-DYN
WS-DYN 03 WS-DYN
3 8
-
29L-FG1L
ITEM IC INITIAL DATA SETTING DATA
S085 UOC-TV 2 2
S086 UOC-TV 1 1
S087 UOC-TV 25 25
S088 UOC-TV 31 31
S089 UOC-TV 36 36
S090 UOC-TV 50 50
S091 UOC-TV 60 60
S092 UOC-TV 60 60
S093 UOC-TV 26 26
S094 UOC-TV 31 31
S095 UOC-TV 36 36
S096 UOC-TXT 25 25
S097 UOC-TXT 18 18
S098 UOC-TXT 48 37
S099 UOC-TXT 0 0
S100 UOC-TXT 10 10
S101 UOC-MCU 1 1
S102 UOC-MCU 3 3
S103 UOC-MCU 0 0
S104 UOC-MCU 1 1
S105 UOC-TV 3 3
S106 UOC-TV 0 0
S107 UOC-TV 0 0
S108 UOC-TV 1 1
S109 UOC-TV 1 0
S110 UOC-TV 0 0
S111 UOC-TV 3 3
S112 UOC-TV 2 2
S113 UOC-TV 1 1
S114 UOC-TV 4 3
S115 UOC-TV 4 7
S116 UOC-TV 3 3
S117 UOC-TV 4 7
S118 UOC-TV 11 3
S119 UOC-TV 8 7
S120 UOC-TV 0 6
S121 UOC-TV 4 13
S122 UOC-TV 0 6
S123 UOC-TV 5 13
S124 UOC-TV 6 6
S125 UOC-TV 10 13
S126 UOC-TV 0 0
03162 U-COL-STD
VMA-CTM 03 VMA-CTM
WS-CTM 03
U-COL-DYN 03162 U-COL-DYN
U-COL-STD
EEPROM SETTING DATA RANGE OSD
U-COL-SOFT 03162 U-COL-SOFT
WS-CTM
U-CON-SOFT 060 U-CON-SOFT
U-CON-STD 060 U-CON-STD
U-CON-DYN 060 U-CON-DYN
U-SHP-SOFT 03162 U-SHP-SOFT
U-SHP-STD 03162 U-SHP-STD
U-SHP-DYN 03162 U-SHP-DYN
OSD-BRIGHTNESS 031 OSD-BRIGHTNESS
V-POS-CURTAIN 063 V-POS-CURTAIN
V-POS-OSD 063 V-POS-OSD
H-POS-FINE 03 H-POS-FINE
H-POS-OSD 063 H-POS-OSD
PW-SAVING 0/1 PW-SAVING
PW-TIME 03 PW-TIME
I-TIME 03 I-TIME
PHI FORCE 0...1 PHI FORCE
PHI 03 PHI
BPD 0/1 BPD
E2D 0/1 E2D
ACL 0/1 ACL
MAT 0/1 MAT
CB 0/1 CB
SVM-OSD-PW 03 SVM-OSD-PW
SMD-OSD-TM 07 SMD-OSD-TM
XDT 0/1 XDT
WBF-50-F-C-P 015 WBF-50-F-C-P
WBR-50-F-C-P 015 WBR-50-F-C-P
WBF-50SUBTITLE 015 WBF-50SUBTITLE
WBR-50-SUBTITLE 015 WBR-50-SUBTITLE
WBF-50-OTHER 015 WBF-50-OTHER
WBR-50-OTHER 015 WBR-50-OTHER
WBF-60-F-C-P 015 WBF-60-F-C-P
WBR-60-F-C-P 015 WBR-60-F-C-P
WBF-60SUBTITLE 015 WBF-60SUBTITLE
WBR-60-SUBTITLE 015 WBR-60-SUBTITLE
WBF-60-OTHER 015 WBF-60-OTHER
WBR-60-OTHER 015 WBR-60-OTHER
FSL 0/1 FSL
3 9
-
29L-FG1L
ITEM IC INITIAL DATA SETTING DATA
S127 UOC-TV 0 0
S128 UOC-TV 15 *1
S129 UOC-TV 14 *2
S130 UOC-TV 12 *3
S131 UOC-TV 15 10
S132 UOC-TV 5 5
S133 UOC-TV 0 0
S134 UOC-TV 1 1
S135 UOC-TV 25 34
S136 UOC-TV 1 0
S137 UOC-TV 31 31
S138 UOC-TXT 0 0
S139 UOC-TXT 0 0
S140 UOC-TXT 0 0
S141 UOC-TXT 0 0
S142 UOC-TXT 0 0
S143 UOC-TV 0 0
S144 UOC-TV 0 0
S145 UOC-TV 1 0
S146 UOC-TV 1 0
S147 UOC-TV 0 1
S148 UOC-TV 1 0
S149 UOC-TV 0 0
SETTING DATA RGB GAIN FOR DIFFERENT CRT
SETTING
DATA
*1
*2
*3
SETTING DATA FOR BELOW ITEM BASED ON DIFFERENT MODEL
SETTING
DATA
*4
*5
*6
HP2 0/1 HP2
GAIN-RED 0127 GAIN-RED
GAIN-GREEN 0127 GAIN-GREEN
GAIN-BLUE 0127 GAIN-BLUE
AUTO-AGC-MAX 032 AUTO-AGC-MAX
SVM2-0-NTSC
IFO-TV-MODE 07 IFO-TV-MODE
0..7SVM2-0-NTSC
062 COL-DVD-PAL
PWL 0/1 PWL
VER-AMP-START 063 VER-AMP-START
VPTXT-UNUSED 063 VPTXT-UNUSED
EEPROM SETTING DATA RANGE OSD
DSK-PAL-AV 0/1 DSK-PAL-AV
COL-DVD-PAL
HPTXT1-UNUSED 063 HPTXT1-UNUSED
HPTXT2A-UNUSED 063 HPTXT2A-UNUSED
HPTXT2B-UNUSED 063 HPTXT2B-UNUSED
BOXBPOS-UNUSED 0127 BOXBPOS-UNUSED
EW-TXT-UNUSED 063 EW-TXT-UNUSED
H-SHI-UNUSED 063 H-SHI-UNUSED
DSK-PAL-DVD 0/1 DSK-PAL-DVD
DSK-NOT-PAL-DVD 0/1 DSK-NOT-PAL-DVD
NRR 0/1 NRR
MUS-NTSC-MAT 0/1 MUS-NTSC-MAT
DTRC-TRAP 0/1 DTRC-TRAP
ITEMEEPROM
SETTING LG CRT
SETTING DATA
MTPD CRT
S130 GAIN-BLUE 12
S128 GAIN-RED 14
S129 GAIN-GREEN 14
ITEMEEPROM
SETTING A3HE9LFG1M
SETTING DATA
S061 OF-COLOR-AV 39
S062 OF-COLOR-DVD 41
20
20
18
S075 OF-TINT-AV 37
A3HE9LG1LA/PA
34
38
35
3 10
-
29L-FG1L
Setting Mode 3 Items
ITEM EEPROM SETTING DATA RANGE IC OSD INITIAL DATA SETTING
DATA
S301 FMI 0/1 DSP FMI 0 0
S302 BPB 0/1 DSP BPB 0 0
S303 BPB2 0/1 DSP BPB2 1 1
S304 FILTBW-M 03 DSP FILTBW-M 0 0
S305 ID-BYBPF 0/1 DSP ID-BYBPF 0 0
S306 ID-PGAIN 0/1 DSP ID-PGAIN 0 0
S307 MPX-P-BW 0/1 DSP MPX-P-BW 0 0
S308 FMSUB-BW 0/1 DSP FMSUB-BW 0 0
S309 EIAJ-DEL 03 DSP EIAJ-DEL 0 0
S310 NDETPB 0/1 DSP NDETPB 0 0
S311 NICDEEM 0/1 DSP NICDEEM 0 0
S312 NLOERLIM 0255 DSP NLOERLIM 100 100
S313 NUPERLIM 0255 DSP NUPERLIM 200 200
S314 FILTBW 03 DSP FILTBW 0 0
S315 OVMTHR 03 DSP OVMTHR 1 1
S316 DECLEV 0...31 DSP DECLEV 16 8
S317 MONOLEV 0...31 DSP MONOLEV 16 9
S318 NICLEV 0...31 DSP NICLEV 16 18
S319 SAPLEV 0...31 DSP SAPLEV 16 6
S320 ADCLEV 0...31 DSP ADCLEV 16 14
S321 IISLEV 0...31 DSP IISLEV 16 16
S322 MAINLOUD 0/1 DSP MAINLOUD 0 0
S323 MAINLONA 0...7 DSP MAINLONA 0 0
S324 MAINLOCH 0...3 DSP MAINLOCH 0 0
S325 INSOEF 0...7 DSP INSOEF 3 3
S326 AVLMOD 0...7 DSP AVLMOD 0 5
S327 AVLWGT 0/1 DSP AVLWGT 1 1
S328 AVLLE 015 DSP AVLLE 7 8
S329 CLIPMANAGE 04 DSP CLIPMANAGE 0 3
S330 VDSMIXLEV 05 DSP VDSMIXLEV 3 3
S331 DBEADR 063 DSP DBEADR 0 0
S332 DBECOEF-LBS 0255 DSP DBECOEF-LBS 0 0
S333 DBECOEF-MBS 015 DSP DBECOEF-MBS 0 0
S334 DUBADR 0255 DSP DUBADR 0 0
S335 DUBCOEF-LSB 0255 DSP DUBCOEF-LBS 0 0
S336 DUBCOEF-MSB 015 DSP DUBCOEF-MBS 0 0
3 11
-
29L-FG1L
ITEM EEPROM SETTING DATA RANGE IC OSD INITIAL DATA SETTING
DATA
S337 BAMAMO 03 DSP BAMAMO 0 0
S338 BAMASUB 0/1 DSP BAMASUB 0 0
S339 BAMAFC 015 DSP BAMAFC 0 12
S340 BASS-MV 0...31 DSP BASS-MV 16 30
S341 TREB-MV 0...31 DSP TREB-MV 16 19
S342 EQ100-MV 0...31 DSP EQ100-MV 12 21
S343 EQ300-MV 0...31 DSP EQ300-MV 12 15
S344 EQ1K-MV 0...31 DSP EQ1K-MV 12 20
S345 EQ3K-MV 0...31 DSP EQ3K-MV 12 15
S346 EQ8K-MV 0...31 DSP EQ8K-MV 12 21
S347 BASS-MS 0...31 DSP BASS-MS 16 30
S348 TREB-MS 0...31 DSP TREB-MS 16 19
S349 EQ100-MS 0...31 DSP EQ100-MS 12 20
S350 EQ300-MS 0...31 DSP EQ300-MS 12 16
S351 EQ1K-MS 0...31 DSP EQ1K-MS 12 11
S352 EQ3K-MS 0...31 DSP EQ3K-MS 12 16
S353 EQ8K-MS 0...31 DSP EQ8K-MS 12 20
S354 BASS-NW 0...31 DSP BASS-NW 16 30
S355 TREB-NW 0...31 DSP TREB-NW 16 19
S356 EQ100-NW 0...31 DSP EQ100-NW 12 11
S357 EQ300-NW 0...31 DSP EQ300-NW 12 16
S358 EQ1K-NW 0...31 DSP EQ1K-NW 12 21
S359 EQ3K-NW 0...31 DSP EQ3K-NW 12 16
S360 EQ8K-NW 0...31 DSP EQ8K-NW 12 11
S361 BASS-CT 0...31 DSP BASS-CT 16 30
S362 TREB-CT 0...31 DSP TREB-CT 16 19
S363 IDMOD-SE 03 DSP IDMOD-SE 0 0
S364 BPR-VOL 060 DSP BPR-VOL 45 30
S365 DEMUT-DLAY 015 DSP DEMUT-DLAY 8 8
S366 AV-OUT LV 0 .. 255 DSP AV-OUT LV 16 11
S367 FMWS-1-0-TV 0...3 DSP FMWS-1-0-TV 1 1
S368 BASSON 0/1 DSP BASSON 0 1
S369 EQ-OFFSET 0/1 DSP EQ-OFFSET 0 1
S370 VAO-LV 060 DSP VAO-LV 0 60
3 12
-
29L-FG1L
(1) The following default data has been factory-setting for the
EEPROM.
Model-Set: The data in table below (1.1), Model set overview is
updated to the respective EEPROM location base on
RC key input Model Set 1.
MODEL-SET KEY
1
Default Settings
Note : * The CHILD LOCK PASSWORD and VIEW TIMER PASSWORD are
common use.
* AFT always ON
* Colour Systems always NTSC M
* Sound System always NTSC M (mono), BTSC M (stereo)
* No MCL feature, all channel frequency is fixed. (Refer to US
channel plan : AIR, IRC, HRC, STD)
* Model set key ( model set 1) will not affect channel frequency
(all refer to US channel plan)
WHITE TEMP
BRIGHTNESS
SOUND menu
+6
0
0
SURROUND EPS
BALANCE 0
PICTURE menu
VIDEO MODE DYNAMIC
60CONTRAST
TINT
EQUALIZER menu
MOVIE
INSET menu (for PIP model)
0
0
MODE
MODE FULL
V-SCROLL 0
0V-SIZE
FEATURE menu
Cable Type AIR
CH SETTING menu
PASSWORD
BEEP REMINDER OFF
SKIP
BBE ON
BASS+ ON
AVL ON
VOLUME _ _
VIEW TIMER menu
REMINDER _ _:_ _
+6
WIDE MODE menu
OFF TIMER _ _:_ _
VIEWING TIME _ _:_ _
All Programs OFF
0000
LOCK OFF
0000
0 (CENTER)
PICTURE NR OFF
VIRGIN mode ON
COLOUR
BRIGHTNESS
TINT
SHARPNESS
POSITION _ _
OFF
CHILD LOCK menu
LOCK STATUS OFF
ON TIMER _ _:_ _
TIMER menu
PASSWORD
SAP mode All Programs MAIN
MTS MONO mode
Volume 0
All Programs MONO
MTS STEREO mode All Programs STEREO
Program 30
100 key digit entry 2 digit entry
16:9 MODE OFF
Favorite Program D Program 40
OFF
Favorite Program B Program 20
Favorite Program A Program 10
ROTATION 0
OFF
AUTO SELECT ON
POWER SAVE OFF
OFF
Flashback Program-TV Program 2
Last TV/AV mode TV mode
Last position-TV Program 2
Last power ON
COMFY VIEW
SHIPPING SETTING & CHECKING
OSD LANGUAGE
English
Default Settings
GENERAL
Items Default Settings Items
SAFETY MODE
Favorite Program C
BLUE BACK
LOCK TV
For model Set 1, the respective
EEPROM position is updated
again with the data attached at the
back
3 13
-
29L-FG1L
(1) Refer to below table (2.1) for setting of each
destination.
MODEL LANGUAGE S-SYS
MEXICO 30,000 25,000 ENGLISH M
LATIN AMERICA (N) 20,000 30,000 ENGLISH M
LATIN AMERICA (S) -10,000 25,000 ENGLISH M
Table 2.1
(2) refer to below table (2.2) for Normal setting of each AV
mode.
MODE
CONTRAST
COLOUR
BRIGHTNESS
TINT
SHARPNESS
PICTURE NR
WHITE TEMP.
Table 2.2
FACTORY SET
-4
MODEL SET 1
60
+6
DYNAMIC SOFT
50
-4
0
0
0
0
OFF
0 (center)
+6
0 (center)
OFFOFF
0 (center)
MAGNETIC FIELD (V,H)nT BACKGROUND
11600K
STANDARD
1
60
+1
0
0
11600K MODEL SET 1
11600K MODEL SET 1
3 14
-
29L-FG1L
[2] ADJUSTMENT
PIF ADJUSTMENT CHECKING
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR
REMARKS
1 RF-AGC (1) Receive "US 10CH HALF COLOR BAR" signal.
TAKE OVER POINT Signal Strength: 56 1dBV (75 ohm termination)
Confirmation Voltage : 3.6 0.4 VDC
ADJUSTMENT Monitor point : TP53
(I2C BUS CONTROL) Manual Adjustment
(2) Connect the oscilloscope to TP53 (Tuner's AGC Terminal) as
shown in figure 3-1.
OSCILLOSCOPE
BIAS BOX
TV SET
Bias Box : about 4.5V
Fig. 3
(3) Select "RF-AGC" item in the Adjustment Mode. Adjust the
"RF-AGC"
bus data to obtain the Tuner output pin drop 0.1V 1.0V below
maximum voltage.
Auto Adjustment
(4) Select "RF-AGC" item in the Adjustment Item. Push the RF-AGC
button, blue display with
OK sign indicates the adjustment is working properly.
(5) Change the antenna input signal to 63 ~ 67dBV, and make sure
there is no noise.
(6)Turn up the input signal to 90 ~ 95 dBB to be sure that there
is no cross modulation beat.
PURITY ADJUSTMENT
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR
REMARKS
1 PURITY ADJ. (1) Select the green monocolor screen with remote
contoller, and set the beam current of
900200A with the contrast control.
(no need this adjutment for (2) Degauss the CRT enough with the
degausing coil. a b
ITC AK MASK CRT type) NOTE: Follow the job instruction manual to
adjust the magnetic field.
(3) The purity magnet must be previously set at the 0 magnetic
field, and the
convergence must be adjusted to be rough. 90 mm 90mm
With P-MAG, adjust it to the center - rank A. Fig. 1 -1
(4) Observe the points a,b, as shown in Fig.1-1 through the
microscope.
Move DY fore and aft to set the landing at the point to be
"inside 2010m (for MTPDT)" or "inside 010m (for MTPDM)".
(5) If the a/b balance is poor, compensate it to the center
"Rank AB".
(6) Aline it to zero, keeping the raster rotation in the east
direction. A
(7) Tighten the deflection coil fastening screws. A=B
Tightening torque : 108N 20N ( 11Kgf 2Kgf ) B
(8) Checking the CRT corner area, bond the magnetic sheet to set
the landing at
rank A for compensation.
Fig 1 -2 . Inside 2010m (for MTPDT);
Note: Apply the adjustment after aging with the beam current
900200A or more Inside 010m (for MTPDM)
for 30 minutes or more.
Note: Select the service mode, and press the monocolor key of
R/C for process,
and the monocolor screen (green) will be selected. A
A=B
* Every push of the monocolor key, changes the screen as
follows. B
Fig 1 -3 . Inside 2010m (for MTPDT);
Inside 010m (for MTPDM)
*Continuously press the monocolor key
1 second or more, and the monocolor mode
will be selected without the service mode.
*Even with TEXT key or "R/G/B" key,
it can be directly switched to each monocolor
screen.
2 UNIFORMITY Before adjustment begin,Horizontal magnetic field =
0G
ADJUSTMENT Vertical magnetic field = Each destination's
adjustment magnetic field
(To perform after the Make sure to degauss it.
purity and
convergence (North direction red uniformity)
adjustment) (1) Horizontal mf = Set to monocolor screen red and
adjust to +0.20G.
(2) Pay attention to the edge of CRT,if the landing is poor
adjust by attaching the
the compensation magnet at the back of CRT. (CRT surface)
(refer to Fig-1)
Mislanding
(South direction red uniformity)
(1) Horizontal mf = Set to monocolor screen red and adjust to
-0.20G.
(2) Pay attention to the edge of CRT ,if the landing is poor
adjust by attaching the
compensation magnet at the back of CRT.
(The same method is applied for adjustment of monocolor screen
blue for
blue uniformity ,and changing both the magnetic field for north
and south
direction.) (CRT back)
*During the pasting of compensation magnet , use the crosshatch
pattern . compensation magnet
Make sure there is no blur or bendlines occur.
If the blur or bend are serious,adjust the location of
compensation magnet Fig-1
to make it better.
+
-
+
-
TP510.1V
1.0V
Monocolor screen
release
mono color
GREEN
SCREEN
mono color
BLUE
SCREEN
mono color
RED
SCREEN
mono color
WHITE
SCREEN
3 15
-
29L-FG1L
CONVERGENCE ADJUSTMENT
NO ADJUSTMENT POINT
1 CONVERGENCE ADJ
(1) Receive the " Crosshatch Pattern" signal.
( To be done after the X axis
purity adjustment.) (2) Using the remote controller, call NORMAL
mode.
(no need this adjutment for ( Static convergence ) Y axis
ITC AK MASK CRT type) 1. Overlap blue and red with the
open-/closing angle and rotation of the 4 pole
magnet. B R R B
2. Overlap green on blue and red with the open-/closing angle
and rotation of the
6 pole magnet.
( Dynamic convergence )
1. Fix the wedges in a position so that the deflection york neck
is at the center of Fig-1
top bottom and left right. ( Straight line and without any blur
horizontal / vertical Adjust by VR1
line).
2. Adjust the Red, Blue, upper and lower of the centre y axis on
the screen by using
the Volume (VR2, VR1)at the deflection york. B R R B
(Refer to fig.1 and fig.2)
3. If the Horizontal Red, Blue(XV) on the screen centre X axisis
shifted, correct the
Red, Blue (XV) by adjusting the balance coil on the deflection
york.
(Refer to Fig. 3)
4. After confirm that there is no problems on the entire screen
,bond each wedge on Fig-2
CRT and glass tape on it. Fastening the screws of DY and magnet
unit Adjust by VR2
(purity , 4 - pole and 6 pole ), then coat the lacquer paint on
DY fastening screw and
magnet unit fastening screw.
VR1
R B
VR2
Fig- 3
Adjust by Balance Coil
Balance Coil
(note)
In case of poor convergence adjustment on the top and bottom and
of the screen ,
adjust DY by swing rightward and leftward.
(Refer to Fig-4)
Fig-4
Adjust by Swing DY
FOCUS ADJUSTMENT
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR
REMARKS
1 FOCUS 1. Receive US-12CH Lion Head.
ADJUSTMENT 2. With the remote controller, make the image
normal.
3. Adjust the focus VR to make the character"575" on left bottom
of monoscope
as fine as possible.
CUT OFF, BKGD, SUB-CONT ADJUSTMENT
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR
REMARKS
1 CRT CUTOFF Note :
ADJUSTMENT 1. Before CRT cutoff adjustment, make sure following
items are in INITIAL DATA.
(I2C BUS CONTROL) a) A020 CUT-RS = 32
b) A021 CUT-GS = 32
c) A109 CUT OFF = 13
(1) Switch TV to video mode , blue back off , with no video
signal
and Press R/C to set picture into normal condition
(2) Go to service mode at adjustment mode item A127 (VG2).
(3) Adjust screen voltage until retrace line appear, the
following OSD will appear at bottom of
screen.
UNSTABLE
OUT
ABOVE
(4) Finally , slowly decrease the screen variable resistor until
following OSD appear.
STABLE
IN
ABOVE / BELOW *
* The last OSD row is the indication of the screen voltage
value. If it show "BELOW",
please increase the screen voltage and vice versa until "STABLE"
AND "IN" OSD appear.
Note :
No matter the indication of last row's OSD is indicate "ABOVE"
or
"BELOW", the important thing is OSD change to "STABLE" and
"IN".
ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR REMARKS
CRT NECK
LacquerPurity Magnet4-Pole Magnet
6-Pole Magnet .
25mm + 0.5mm
3 16
-
29L-FG1L
CUT OFF, BKGD, SUB-CONT ADJUSTMENT CONTINUED
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR
REMARKS
2 WHITE BALANCE (1) Receive the internal RF monoscope
pattern.
BACKGROUND (2) Make the picture normal with the remote
controller.
I2C BUS (3) Connect the beam ammeter between terminal of R623.
11600K X : 0.273 Y : 0.280
ADJUSTMENT (4) Coarsely confirm the beam current to approx.
1.7mA. ( With Monolta color thermometer CA-100)
(US-14 CH) (5) Receive the window pattern US-14 channel.
(6) With the data of DRI-GS and DRI-BS, adjust the color
temperature of the 50% white.
(7) Adjust the right dark area of the window to 11600K with
CUT-RS and CUT-GS
(8) Go back to 50% white area to check colour temperature, if
out of range, please
go back to step (6).
* 11600K
DRI-GW = "DRI-GS" - 7
Note 1: Apply this adjustment after aging 30 min or more with
the beam current DRI-BW = "DRI-BS" - 7
1700 50A. (On the white or green monocolor screen) DRI-GC =
"DRI-GS" - 7
DRI-RC = 25
2: The colour temperature is based on the shipment destination
as shown in Table 2.1 at
page 20.
3: Adjust DRI-GC/GW, DRI-BC/BW , CUT-RW/C and CUT-GW/C as
following DATA,
after finishing DRI-BS and DRI-GS DATA adjustment.
CUT-RW/C = CUT-RS Note 1: Use the window pattern of the
signal
CUT-GW/C = CUT-GS generator SX-1006 for adjustment DVD
DRI-RW = 32 (FIXED), DRI-RS = 32 (FIXED) signal
DRI-BC = "DRI-BS"
3 WHITE BALANCE (1) The window pattern is received with DVD
signal ( component signal).
BACKGROUND
I2C BUS (2) Apply the adjustment in the same manners as 2 (US-14
CH)
ADJUSTMENT and subsequence above.
(DVD SIGNAL) (DRI-GS-DVD, DRI-BS-DVD, CUT-RS-DVD,
CUT-GS-DVD)
Apply the adjustment after the end of 2 (AV-IN SIGNAL).
Note: 1. All of the DRI-GW/C-DVD & DRI-BW/C-DVD can be
obtain by using same 50% white
calculation as white balance adjustment above (No.2). Others
setting data Dark white
are as follow.
CUT-RW/C-DVD = CUT-RS-DVD
CUT-GW/C-DVD = CUT-GS-DVD
DRI-RW-DVD = 32 (FIXED), DRI-RS-DVD= 32 (FIXED)
DRI-BC-DVD = "DRI-BS-DVD"
DRI-RC-DVD = 25
4 SUB-BRIGHTNESS (1) Receive the window pattern US-14
channel.
ADJUSMENT (2) Make the image normal with the remote controller.
Note 1: Use "Y" of Minolta color analyzer
(I2C BUS CONTROL) (3) Select the sub- bright adjustment mode
with the remote controller, and adjust the CA-100 in adjustment
(US-14 CH) right dark white area of the window pattern to 3.0 cd
0.5cd.
Note 2: Use the window pattern of the signal
generator SX-1006 for adjustment
DVD signal.
5 SUB-BRIGHTNESS (1) Select DVD mode.
ADJUSMENT (2) Receive the signal of the DVD signal generator . (
Component signal)
(I2C BUS CONTROL) ( Window Pattern)
(DVD SIGNAL) (3) Make the image normal with the remote
controller.
(4) Select the SUB-BRIGHT adjustment mode (DVD) , and adjust the
right dark white
area of the window pattern to 3.0 cd 0.5cd of the window
pattern.
6 SUB-CONTRAST (1) Receive the window pattern US-14 channel.
I2C BUS (2) Make the image normal with the remote
controller.
ADJUSTMENT (3) Select the SUB-CONTRAST adjustment mode with the
remote controller, and
(US-14 CH) adjust 50% white to 130 10cd.
7 SUB-CONTRAST (1) Select the DVD mode.
I2C BUS (2) Receive the signal of the DVD signal generator. (
Component signal)
ADJUSTMENT (Window Pattern)
(DVD SIGNAL) (3) Select the SUB-CONTRAST adjustment mode (DVD)
with the remote controller,
and adjust 50% white to 130 10cd.
50% whitedark white
3 17
-
29L-FG1L
A
B
C
HORIZONTAL ,VERTICAL,DEFLECTION LOOP AND ADJUSTMENT
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR
REMARKS
1 MAIN SCREEN
ADJUSTMENT
V-SLOPE Adjust V-Slope by Volume Up / Down Remote Control.
(monoscope)
Refer to Fig. 1.1.
VER-AMP-F60 Adjust the overscan to 10% (monoscope)
Fig 1-1
VER-SHI-F60 Align the center of the screen to the geometric
center of CRT. (monoscope)
HOR-SHI-F60 Align the center of the screen to the geometric
center of CRT. (monoscope)
EW-W-F60 Adjust the overscan to 10% (monoscope)
V-LIN Adjust the linearity to the best. (monoscope)
S CORR Already preset.(Adjust this unless the linearity is
achieved.) (monoscope)
Fig 1-2
V-SCROLL Already preset.
VX-NORMAL Already preset.
H-PAR Adjust the 2nd vertical line from the end of the
crosshatch pattern (crosshatch)
Refer to Fig 1.6.
H-BOW Adjust the 2nd vertical line from the end of the
crosshatch pattern Fig 1-3
Refer to Fig 1.7. (crosshatch)
E/W-PAR-F60 Adjust the 2nd vertical line from the right end of
the crosshatch pattern
so that the middle 4 blocks are straight. Refer to Fig 1-2.
(crosshatch)
UPCOR-PAR Adjust the 2nd upper vertical line from the right end
of the crosshatch pattern
so that the upper line are straight. Refer to Fig 1-3.
(crosshatch)
Fig 1-4
LOCOR-PAR Adjust the 2nd lower vertical line from the right end
of the crosshatch pattern
so that the bottom line are straight. Refer to Fig 1-4.
(crosshatch)
EW-TRAP Adjust the 2nd vertical line from the right end of the
crosshatch pattern
so that the D1 (center area of the second vertical line - edge
of screen)
and D2 (top area of the second vertical line - edge of screen)
are same.
Refer to Fig 1-5. (crosshatch)
PAL Adjustment - AV Multi
(using external signal Fig 1-5
to input AV)
VER-AMP-F50 Adjust the overscan to 8.5%. (monoscope)
VER-SHI-F50 Align the center of the screen to the geometric
center of CRT. (monoscope)
HOR-SHI-F50 Align the center of the screen to the geometric
center of CRT. (monoscope)
EW-W-F50 Adjust the overscan to 10% . (monoscope)
E/W-PAR-F50 Adjust the 2nd vertical line from the right end of
the crosshatch pattern
so that the middle 4 blocks are straight. Refer to Fig 1-2.
(crosshatch)
NOTE :
There are no separate adjustment for 16:9 mode and Normal mode
adjustment.
The 16:9 (Panorama mode ) data need to follow the adjusted data
for
Normal mode . Please set the data as below.
VER-AMP-P60 = VER-AMP-F60
VER-SHI-P60 = VER-SHI-F60
HOR-SHI-P60 = HOR-SHI-F60
EW-W-P60 = EW-W-F60
E/W-PAR-P60 = E/W-PAR-F60
VER-AMP-P50 = VER-AMP-F50
VER-SHI-P50 = VER-SHI-F50
HOR-SHI-P50 = HOR-SHI-F50
EW-W-P50 = EW-W-F50
E/W-PAR-P50 = E/W-PAR-F50
D2
D1
H-PAR
Fig 1.6
Fig 1.7
A = Out of spec
B = OK
C = Out of spec
H-BOW
3 18
-
29L-FG1L
NTSC CHROMA ADJUSTMENT
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR
REMARKS
1 SUB COLOUR (1) Receive the US10 Half Color Bar signal.
(I2C BUS CONTROL) (2) Make the image normal with the remote
controller.
(3) Connect the oscilloscope to TP47R (IC851 #9).(Use Probe
10:1)
Range : 2V / Div Sweep time: 20m sec / Div
(4) Set the sub color adjustment mode with the remote
controller, and vary the sub
color data to make 100% W of the color bar and RED at the same
level for R and
adjustment shown in Fig. 1-1. 100% Wh
same level
(5) For LAG model only (29L-FG1L), please add +3 from the value
data that get at (4) procedure.
Fig. 1-1
NTSC CHROMA ADJUSTMENT
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR
REMARKS
1 SUB-TINT (1) Receive the "US 10CH Half Color Bar" signal.
(I2C BUS CONTROL) (2) Connect the oscilloscope to TP47B (P860
Pin6) BLUE-OUT
Range : 100mV/Div (AC) (Use Probe 10:1)
Sweep time : 10sec/Div
(3) Select the "SUB-TINT" item in the ADJUSTMENT MODE.. Adjust
the "SUB-TINT"
data to obtain the waveform shown as Figure 1.2 (Cy and Mg same
level)
Fig. 1-2
PROTECTOR OPERATION CHECK
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR
REMARKS
1 H.V Protector (1) Receive Monoscope pattern (US12 CH)
Ref : Apx.13.3V.
(2) Connect the bias box to the cathode side (R607) of D604.
(3) Set the voltage of the bias box at 10V, and verify that the
protector does not operate.
(4) Set the voltage of the bias box at 18V, and verify that the
protector operate.
SOUND OUTPUT CHECKING
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR
REMARKS
1 Front speaker output (1) Receive the US-10 Half Color Bar.
checking
(2) Set the volume to maximum and set the other sound setting as
follow.
Setting item #1 : Sound setting for model
Equalizer with BBE and Super Bass
Surround in the sound menu.
BBE
Balance #2 : Sound setting for model
AVL without BBE and with
Super Bass Bass + in the sound menu.
Bass +
(3) Connect the voltmeter to the speaker terminal and make sure
the reading is 5.5 0.5 Vrms.
Same Level
#1 #2
Music Music
OFF OFF
OFF -
0 0
OFF OFF
OFF -
- ON
W Y Cy G Mg R B
W
3 19
-
29L-FG1L
FUNCTION OPERATION CHECKING (1) (VIDEO & AUDIO)
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR
REMARKS
1 CONTRAST Key (1) Receive "Monoscope Pattern" signal.
(2) Press to Menu mode, then select Picture Mode and set to
select CONTRAST.
(3) Press Volume Up/Down key to check whether the CONTRAST
effect is OK or not.
2 COLOUR Key (1) Receive "Colour Bar" signal.
(2) Press to Menu mode, then select Picture Mode and set to
select COLOUR.
(3) Press Volume Up/Down key to check whether the COLOUR effect
is OK or not.
3 BRIGHTNESS Key (1) Receive "Monoscope Pattern" signal.
(2) Press to Menu mode, then select Picture Mode and set to
select BRIGHTNESS.
(3) Press Volume Up/Down key to check whether the BRIGHTNESS
effect is OK
or not.
4 TINT Key (1) Receive the "NTSC Colour Bar" signal thru AV
in.
(2) Press to Menu mode, then select Picture Mode and select
TINT.
(3) Press Volume Up/Down key to check TINT, UP for GREEN
direction and
DOWN for RED direction whether is OK or not.
5 SHARPNESS Key (1) Receive "Monoscope Pattern" signal.
(2) Press to Menu mode, then select Picture Mode and set to
select SHARPNESS.
(3) Press Volume Up/Down key to check whether the SHARPNESS
effect is OK or NOT.
6 NORMAL KEY (1) Once in PICTURE Mode,and the NORMAL key is
pressed, Note :
all the settings will be present to normal setting. If nothing
is display mean contrast,
(Normal setting value for every mode, refer Table 2.2 on page
20). colour, bright, tint, sharpness are
all in normal setting.
7 WHITE TEMP (1) Receive "Monoscope Pattern" signal.
(2) Set FUNCTION to select WHITE TEMP.
(3) Press Volume Up/Down key to check WHITE TEMP Option,
STANDARD:
NORMAL SETTING, WARM for more REDDISH direction changing, COOL
for
more BLUISH direction changing.
8 NOISE MUTE (1) Receive "US10 Half Color Bar" signal.
CHECKING
(2) Turn up the volume control to maximum, make sure the sound
is
heard from the speakers. Then put the unit in no signal
state.
(3) Check the sound mute is effective.
(4) Finally turn sound level of CTV to minimum.
3 20
-
29L-FG1L
TV29L-FG1LService Manual29L-FG1LMarketE CHAPTER 4. TROUBLE
SHOOTING FLOWCHART
[1] TROUBLE SHOOTING FLOWCHART
NO RASTER
LED COLOUR ?
Power on by R/C
Check protectorcircuit and pin 106 &107 (waveform no.3
&4) of IC 2100. Alsocheck the waveformno.7 of IC501 at pin 5and
its related parts.
Does horizontalcircuit momentary
oscillate ?
Check CRT connector(KY), (H) bias.(Heater voltage,120 V,
210 V line)
Abnormal
Check R,G,Binput and outputof IC 851.
Check the
Heater voltage,
120V and 210Vline from themain PWB side.
RED
GREEN
RED
Yes No
Normal
Check 3.3 V & 1.8 V
supplies of IC 2100.
Check oscillation of
crystal X2001.
4 1
-
29L-FG1L
NO LED LIGHT
Check F4701
Normal Blown out
Replace the fuse
Is the fuse again blown out ?
Does STBY+5V appear at pin 4IC752 main unit ?
No
Check the power circuitconsisting of IC701,IC702, T701 and
itsrelated parts.
Yes
Check the powercircuit consisting ofIC701, IC702, T701and its
related parts.
Check 3.3V outputfrom pin 1 of IC704 and its relatedparts.
No Yes
4 2
-
29L-FG1L
NO NORMAL SOUND
Set volume to maximum. Is thereany sound output signal at pin 11
&9 of IC301 ?
Check outputsignal at pin 68,69 of IC2100 andits related
circuit.
No sound from thespeaker.
No soundcomes out atAV-out J905.
Check if there issound input signalat pin 2 & 4 ofIC301.
NO YES
Check connectionto the speaker.
NO
Check sound outputsignal from pin 92 &93 of IC2100 and
itsrelated circuit.
4 3
-
29L-FG1L
NO PICTURE
Does the snow noiseappear on the screen atmaximum contrast
andbrightness ?
Snow noiseincrease
Does 5V appearat pin 7 of TU 51 ?
Does 31V appearat pin 9 of TU 51 ?
Check TU 51
Check the PC+5V line.
Check +120V line andits related circuit.
YES
YES
YES
NO
NO
ANO
4 4
-
29L-FG1L
No snow noise
Check pin 104 &105 of IC 2100.
Normal Abnormal
Noise or signalappear.
Check TU 51 (Tuner),SF 202 and itsrelated circuit.
Does AV input atAV1 & AV2 normal ?
Check pin 71 & 78 ofIC 2100. Does signalor noise appear
?
NO
Check IC 2100 andits related circuits.
YES
Check circuitbetween AV-interminal and pin 71 &78 of IC
2100.
NO
YES Check IC 2100 RGBout at pin 42, 43 & 44.Is the output
normal ?
Check IC 2100 andits related circuit.
NO
YES Does signal outputat pin 7, 8 & 9 ofIC 851 normal ?
Check IC 851 atinput pin 1, 2 & 3and its relatedcircuit.
NO
Check the relatedcircuit of screenheater (FBT) and
A
YES
the CRT.
4 5
-
29L-FG1L
NO SPECIFIC COLOUR
Is only RF signal's colourabnormal ?
Check tuner TU 51,
SF 202 and its relatedcircuit.
YES
NO
NO COLOUR COLOUR PRODUCED
Adjust the colourcontrol at the userMENU. Does colourappear
?
Go to CHANNELSETTING at the userMENU and changeto the
appropriatecolour system. Doesthe colour appear ?
NO
Set theappropriatecolour level.
Set theappropriatecolour system.
YES
YES
Using a PAL colourbar signal, check theRGB in & out
linebetween IC 2100 andIC 851. Does thewaveforms normal ?
NO
Check IC 851, IC2100 and its relatedcircuit.
NO
B
4 6
-
29L-FG1L
Is some colours producedin the B/W broadcastreception ?
Check IC 2100& IC 851 and itsrelated circuitincluding theRGB
input &output line.
NO YES
Is the white balanceproperly adjusted ?
Readjust the white
balance.
NO
The picturecolour is cyan.
The picturecolour ismagenta.
The picturecolour isyellow.
Check pin 9 ofIC 851 (R-out).
Check pin 8 ofIC 851 (G-out).
Check pin 7 ofIC 851 (B-out).
YES
B
4 7
-
29L-FG1L
5 1
TV29L-FG1LService Manual29L-FG1LMarketE CHAPTER 5. SOLID STATE
DEVICE BASE DIAGRAM
[1] SOLID STATE DEVICE BASE DIAGRAM
FXA003W
2 3
1 4
D5SB 60 74
DX0477
USOLID STATE DEVICE BASE DIAGRAM
TOP VIEW
SIDE VIEW
ANODE (RED)
CATHODE
ANODE (GREEN)
PX0037DX0445
ANODE CATHODE
SC3198
E C B
M24C16W
1 4
5800K5W
D00K5WP
BC0W
A50B0W
1 4
58
D33KA5W
1
32
33 64
96
65
97128
RH-IXB841WJZZQ B709AR
BR
COLLECTOR
BASE EMITTER
2SC2735
JC
COLLECTOR
BASE EMITTER
D601AR
ZR
COLLECTOR
BASE EMITTER
A42072N-1 A4863AJ
1 7 1 6
TRW6556
D2646
LOTNO.
SD2646
M1431AT
K G A
SK2161
-
29L-FG1L
6 1
TV29L-FG1LService Manual29L-FG1LMarketE CHAPTER 6. CHASSIS
LAYOUT
[1] CHASSIS LAYOUT
-
29L-FG1L
7 1
TV29L-FG1LService Manual29L-FG1LMarketE CHAPTER 7. DESCRIPTION
OF SCHEMATIC DIAGRAM
[1] DESCRIPTION OF SCHEMATIC DIAGRAM
-
29L-FG1L
TV29L-FG1LService Manual29L-FG1LMarketE CHAPTER 8. BLOCK
DIAGRAM
[1] BLOCK DIAGRAM : MAIN UNIT
8 1
-
29L-FG1L
8 2
-
29L-FG1L
9 1
TV29L-FG1LService Manual29L-FG1LMarketE CHAPTER 9. WAVEFORM
[1] WAVEFORM
Vp-p = 2.02 V Vp-p = 1.30 V Vp-p = 2.26 V Vp-p = 2.40 V
Horizontal Rate Horizontal Rate
WAVEFORMS
Vertical Rate Vertical Rate
Vp-p = 4.26 V Vp-p = 29.40 V Vp-p = 52.70 V Vp-p = 1.80 V
Vertical Rate Vertical Rate Vertical Rate Vertical Rate
Vp-p = 262.0 V Vp-p = 262.0 V Vp-p = 178.0 V Vp-p = 11.20 V
Horizontal Rate Horizontal Rate Horizontal Rate Horizontal
Rate
Horizontal Rate Horizontal Rate Horizontal Rate Horizontal
Rate
Horizontal Rate
Horizontal Rate
Horizontal Rate Horizontal Rate Horizontal Rate
Vp-p = 1.024 kV Vp-p = 248.0 V Vp-p = 31.20 V Vp-p = 1.84 V
Vp-p = 2.04 V
Vp-p = 134.0 V
Vp-p = 2.10 V Vp-p = 120.0 V Vp-p = 106.0 V
1 2 3 4
5 6 7 8
9 1110 12
151413 16
191817
21
20
-
29L-FG1L
TV29L-FG1LService Manual29L-FG1LMarketE CHAPTER 10. SCHEMATIC
DIAGRAM
[1] SCHEMATIC DIAGRAM : CRT UNIT
10 1
-
29L-FG1L
[2] SCHEMATIC DIAGRAM : MAIN UNIT
10 2
-
29L-FG1L
10 3
-
29L-FG1L
TV29L-FG1LService Manual29L-FG1LMarketE CHAPTER 11. PRINTED
WIRING BOARD ASSEMBLIES
[1] PWB-A : MAIN UNIT
1. MAIN UNIT (COMPONENT SIDE)
11 1
-
29L-FG1L
11 2
-
29L-FG1L
2. MAIN UNIT (CHIP PARTS SIDE)
11 3
-
29L-FG1L
11 4
-
29L-FG1L
[2] PWB-B : CRT UNIT
11 5
-
29L-FG1L
PartsGuide
PARTS GUIDENo. XXXXXXXXXXXX
XXXXXXXXMODEL
CONTENTS
29L-FG1L
S677529LFG1L
[1] PICTURE TUBE
[2] PRINTED WIRING BOARD ASSEMBLIES
[3] MAIN UNIT
[4] CRT UNIT
[5] MISCELLANEOUS PARTS
[6] ACCESSORIES PARTS
[7] CABINET PARTS
[8] PACKING PARTS ( NOT REPLACE-MENT PART )
INDEX
Parts marked with " " are important for maintaining the safety
of the set. Be sure to replace theseparts with specified ones for
maintaining the safety and performance of the set.
This document has been published to be usedfor after sales
service only.The contents are subject to change without notice.
-
29L-FG1L
PRICE NEW PART DELIVERY
NO. PARTS CODE RANK MARK DESCRIPTION
[1] PICTURE TUBE! VB68MAU085X3E R S-ITC MTPDT AK(N) Picture
Tube! RCILGA127WJN2 R Degaussing Coil
PMAGG3002CEZZ AC R MagnetQEARCA045WJPZ R Ground-Part
[2] PRINTED WIRING BOARD ASSEMBLIESDUNTKD538WEG1 - - PWB-A :
MAIN UnitDUNTKD539WEE9 - - PWB-B : CRT Unit
[3] MAIN UNIT! TU51 VTUVT1Y5EF201 R Tuner
IC301 VHILA42072N-1 AK R LA42072NIC501 VHITDA4863AJ1 AK R
TDA4863AJ
! IC701 VHISTRW6556-1 AP R STRW6556A! IC702 RH-FXA003WJZZ AD R
PC123Y82
IC704 VHIBD33KA5W-1Y AF R BD33KA5WF-E2IC714 VHIMM1431AT-1+ AD R
MM1431ATTIC751 VHIBA50B0WP-1Y AF R BA50BC0WFP-E2
! IC752 VHIBA50B0WP-1Y AF R BA50BC0WFP-E2IC2031 VHIBD4847G+-1Y
AC R BD4847G-TRIC2100 RH-IXB841WJZZQ R IXB841WIC2101 VHIBR24L16F-1Y
AF R BR24L16F-WE2IC2102 VHIBD00K5WP-1Y AF R BD00KA5WFP-E2IC2104
VHIBD00K5WP-1Y AF R BD00KA5WFP-E2
Q200 VS2SC2735//1EY AC R 2SC2735Q310 VS2PB709AR/-1Y AB R
2PB709ARQ312 VS2PD601AR/-1Y AB R 2PD601ARQ602 VS2SK2161++-1 AG R
2SK2161++Q603 VS2PD601AR/-1Y AB R 2PD601AR
! Q604 VS2SD2646++1E AM R 2SD2646++Q605 VS2PB709AR/-1Y AB R
2PB709ARQ606 VS2SC2482//-1+ AD R 2SC2482Q607 VSKRC103S//-1Y AA R
KRC103SQ609 VS2SC3198-Y-1+ AA R 2SC3198-YQ755 VS2SC3198-G-1+ AA R
2SC3198-GQ902 VS2PD601AR/-1Y AB R 2PD601ARQ903 VS2PD601AR/-1Y AB R
2PD601ARQ904 VS2PB709AR/-1Y AB R 2PB709ARQ905 VS2PB709AR/-1Y AB R
2PB709ARQ906 VS2PD601AR/-1Y AB R 2PD601ARQ907 VSKRC105S//-1Y AB R
KRC105S
Q4001 VS2PB709AR/-1Y AB R 2PB709ARQ4002 VS2PD601AR/-1Y AB R
2PD601AR
D52 RH-EX0677GEZZY AC R Zener Diode , 32VD202 VHD1SS133++-1Y AA
R 1SS133D203 RH-EX0627GEZZY AA R Zener Diode , 8.2VD305
VHD1SS133++-1Y AA R 1SS133D310 VHD1SS133++-1Y AA R 1SS133D311
RH-DX0302CEZZY AC R DX0302CED322 VHD1SS355//-1Y R 1SS355D501
RH-DX0441CEZZY AC R DX0441CED502 VHD1SS133++-1Y AA R 1SS133D503
RH-EX0612GEZZY AB R Zener Diode , 5.2VD601 VHD1SS244//-1Y AB R
1SS244D603 RH-DX0131CEZZY AC R DX0131CE
! D604 RH-EX0640GEZZY AA R Zener Diode , 12.03VD605
RH-DX0302CEZZY AC R DX0302CE
! D606 VHD1SS133++-1Y AA R 1SS133! D607 RH-DX0255CEZZ AC R
DX0255CE! D608 RH-DXA006WJZZ AD R DXA006WJ
D610 RH-EX0612GEZZY AB R Zener Diode , 5.2VD611 RH-DX0302CEZZY
AC R DX0302CED612 VHD1SS133++-1Y AA R 1SS133D613 VHD1SS133++-1Y AA
R 1SS133D616 RH-DX0321CEZZY AC R DX0321CED617 RH-EX0604GEZZY AB R
Zener Diode , 4.16VD671 RH-EX0604GEZZY AB R Zener Diode , 4.16VD703
RH-EX0654GEZZY AB R Zener Diode , 18.96V
! D704 RH-DX0477CEZZ AF R DX0477CED705 VHD1SS133++-1Y AA R
1SS133D708 VHD1SS244//-1Y AB R 1SS244D713 RH-DX0321CEZZY AC R
DX0321CED751 RH-DXA006WJZZ AD R DXA006WJD752 VHD1SS133++-1Y AA R
1SS133D753 RH-DX0302CEZZY AC R DX0302CED755 RH-DX0445CEZZ AL R
DX0445CED757 VHD1SS133++-1Y AA R 1SS133D758 VHD1SS133++-1Y AA R
1SS133D759 VHD1SS133++-1Y AA R 1SS133D901 VHD1SS133++-1Y AA R
1SS133
D2001 VHD1SS133++-1Y AA R 1SS133D2106 RH-EX0630GEZZY AA R Zener
Diode , 9VD2107 RH-EX0630GEZZY AA R Zener Diode , 9VD2108
RH-EX0630GEZZY AA R Zener Diode , 9V
2
-
29L-FG1L
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
D5003 RH-PX0037PEZZ AD R LED (2COLOR)TH701 RH-HXA014WJZZ+ AD R
Thermistor
! PR701 RMPTP0085CEZZ AL R Packaged CircuitRY701 RRLYJ0089CEZZ R
Relay
RMC4001 RRMCUA052WJZZ R RC ReceiverX2001 RCRSAA058WJZZ AD R
Crytal
L51 VP-CF270K0000Y AB R Peaking 27mH 10%L202 VP-DF100K0000Y AB R
Peaking 10mH 10%L203 VP-XF1R2K0000Y AB R Peaking 1.2mH 10%L504
VP-XF220K0000Y AB R Peaking 22mH 10%L601 RCILZ1005CEZZ AH R
CoilL603 RCILZA053WJZZ AG R Coil
! L701 RCILFA144WJZZ AG R CoilL751 RCILP0179CEZZ+ AD R Coil
47mH
L2001 VP-XF220K0000Y AB R Peaking 22mH 10%L2003 VP-MK560K0000+
AB R Peaking 56mH 10%L2004 VP-DF100K0000Y AB R Peaking 10mH
10%L2005 VP-DF100K0000Y AB R Peaking 10mH 10%L2006 VP-DF100K0000Y
AB R Peaking 10mH 10%L2007 VP-DF100K0000Y AB R Peaking 10mH
10%L2008 VP-DF100K0000Y AB R Peaking 10mH 10%L2009 VP-DF100K0000Y
AB R Peaking 10mH 10%L2010 VP-DF100K0000Y AB R Peaking 10mH
10%L2011 VP-DF100K0000Y AB R Peaking 10mH 10%L2012 VP-DF100K0000Y
AB R Peaking 10mH 10%L2013 VP-DF100K0000Y AB R Peaking 10mH
10%L2014 VP-DF100K0000Y AB R Peaking 10mH 10%L2100 VP-DF100K0000Y
AB R Peaking 10mH 10%
! T601 RTRNZA050WJZZ AF R Transformer! T602 RTRNFA100WJZZ AX R
H-Volt Transformer! T701 RTRNWA218WJZZ AP R Transformer
VA4701 RH-VXA182WJZZ R VaristerSF202 RFILCA053CEZZ R Filter
C51 VCEA9M1HW475M+ AB R 4.7 50V ElectrolyticC53 VCEA0A0JW338M AD
R 3300 6.3V ElectrolyticC55 VCEA0A1HW105M+ AB R 1 50V
Electrolytic
C201 VCKYCY1HB103KY AA R 0.01 50V CeramicC202 VCKYCY1HB104KY AA
R 0.1 50V CeramicC205 VCEA0A1CW227M+ AC R 220 16V ElectrolyticC206
VCEA0A1AW477M+ AD R 470 10V ElectrolyticC207 VCEA9M1CW106M+ AB R 10
16V ElectrolyticC208 VCEA9M1HW225M+ AB R 2.2 50V ElectrolyticC209
VCEA9M1HW225M+ AB R 2.2 50V ElectrolyticC210 VCKYCY1AB474KY AB R
0.47 10V CeramicC211 VCKYCY1HB332KY AA R 3300p 50V CeramicC212
VCKYCY1HB103KY AA R 0.01 50V CeramicC213 VCKYCY1HB103KY AA R 0.01
50V CeramicC214 VCKYCY1HB103KY AA R 0.01 50V CeramicC215
VCKYCY1HB103KY AA R 0.01 50V CeramicC216 VCKYCY1AB105KY AB R 1 10V
CeramicC217 VCEA0A1CW107M+ AC R 100 16V ElectrolyticC218
VCKYCY1HB103KY AA R 0.01 50V CeramicC222 VCKYCY1HB104KY AA R 0.1
50V CeramicC223 VCKYCY1HB104KY AA R 0.1 50V CeramicC300
VCKYCY1HB104KY AA R 0.1 50V CeramicC301 VCEA0A1HW108M AE R 1000 50V
ElectrolyticC308 VCKYCY1HB182KY AA R 0.18 50V CeramicC310
VCEA9M1HW225M+ AB R 2.2 50V ElectrolyticC311 VCE9GA1CW106M+ AB R 10
16V ElectrolyticC312 VCE9GA1CW106M+ AB R 10 16V ElectrolyticC313
VCKYCY1HB182KY AA R 0.18 50V CeramicC314 VCEA0A1AW108M+ AD R 1000
10V ElectrolyticC315 VCFYFA1HA474J+ AC R 0.47 50VC316
VCFYFA1HA474J+ AC R 0.47 50VC322 VCEA9M0JW336M+ AB R 33 6.3V
ElectrolyticC323 VCE9GA1CW106M+ AB R 10 16V ElectrolyticC324
VCE9GA1CW106M+ AB R 10 16V ElectrolyticC325 VCEA0A1EW476M+ AB R 47
25V ElectrolyticC501 VCEA0A1EW108M+ AD R 1000 25V ElectrolyticC502
VCEA0A1VW107M+ AC R 100 35V ElectrolyticC503 VCQYTA1HM473J+ AB R
0.047 50V MylarC504 VCEA0A1EW108M+ AD R 1000 25V ElectrolyticC505
VCQYTA1HM473J+ AB R 0.047 50V MylarC519 VCKYCY1AB474KY AB R 0.47
10V CeramicC520 VCCCCY1HH102JY AB R 1000p 50V CeramicC521
VCCCCY1HH102JY AB R 1000p 50V CeramicC522 VCEA9M1HW106M+ AB R 10
50V ElectrolyticC523 VCKYCY1HB223KY AA R 0.022 50V CeramicC524
VCEA0A1HW224M+ AB R 0.22 50V ElectrolyticC525 VCKYCY1AB105KY AB R 1
10V CeramicC526 VCQYTA1HM682K+ AA R 6800p 50V MylarC527
VCQYTA1HM103J+ AB R 0.01 50V MylarC528 RC-EZA151WJZZ+ AD R 0.047
10VC529 VCKYCY1AB474KY AB R 0.47 10V CeramicC600 VCFPFA2EB154J AC R
0.15 250V
[3] MAIN UNIT
3
-
29L-FG1L
PRICE NEW PART DELIVERY
NO. PARTS CODE RANK MARK DESCRIPTION
! C602 VCFPVC3ZA203H R 0.020 1800V! C603 VCQPPC2JB473J AC R
0.047 630V
C605 VCKYPA2HB102K+ AA R 1000p 500V CeramicC608 VCEA4A2EN106M+
AD R 10 250V ElectrolyticC609 VCKYPA2HB102K+ AA R 1000p 500V
CeramicC610 VCEA0A1EW108M+ AD R 1000 25V Electrolytic
! C611 VCEA0A1VW476M+ AC R 47 35V ElectrolyticC612
VCKYPA2HB151K+ AB R 150p 500V CeramicC613 VCCCCY1HH101JY AA R 100p
50V CeramicC615 VCKYPA2HB102K+ AA R 1000p 500V CeramicC616
VCEA0A1EW338M AD R 3300 6.3V ElectrolyticC617 RC-FZA293WJPZ+ R
104pF 100VC618 RC-KZ0033CEZZ+ AB R 150p 2V CeramicC620
VCKYPA1HB472K+ AB R 4700p 50V CeramicC621 VCEA0A1HW476M+ AB R 47
50V ElectrolyticC622 VCKYPA2HB561K+ AA R 560p 500V CeramicC623
VCKYPA2HB272K+ AB R 2700p 500V CeramicC624 VCEA0A1HW475M+ AB R 4.7
50V ElectrolyticC625 VCQYTA1HM104K+ AA R 0.1 50V MylarC627
RC-FZA178WJZZ AG R 4.7 100VC635 VCFPKH2ED514J R 0.51 250VC636
RC-FZ0357CEN1 AE R 0.22 250VC644 VCCCCY1HH102JY AB R 1000p 50V
CeramicC645 VCKYCY1HB104KY AA R 0.1 50V CeramicC701 VCQYTA1HM152J+
AB R 1500p 50V MylarC702 RC-EZA535WJZZ AR RC703 RC-KZ018JCEZZ AC R
0.01 AC250V CeramicC704 RC-KZ018JCEZZ AC R 0.01 AC250V CeramicC705
VCFYFA1HA104J+ AB R 0.10 50VC706 VCEA0A1HW226M+ AB R 22 50V
ElectrolyticC707 RC-KZ1007CEZZ+ AC R 820p CeramicC708
VCQYTA1HM104J+ AB R 0.1 50V MylarC711 RC-FZA097WJZZ AC R 0.22
AC250VC713 VCEA0A1CW106M+ AB R 10 16V ElectrolyticC714
VCKYCY1HB103KY AA R 0.01 50V CeramicC715 VCEA0A1CW476M+ AB R 47 16V
ElectrolyticC716 VCEA0A1CW476M+ AB R 47 16V ElectrolyticC717
VCFYAA2JA103K+ AC R 0.01 630VC752 VCEA0A1CW338M AD R 3300 6.3V
ElectrolyticC754 RC-EZA065WJZZ AK R 330 160VC755 RC-EZA065WJZZ AK R
330 160VC756 RC-KZ0226CEZZ+ AC R 180p 2kvC757 VCEA0A1CW476M+ AB R
47 16V ElectrolyticC758 RC-KZ0120GEZZ AC R 150p 2V CeramicC759
VCEA0A1VW228M AE R 2200 35V ElectrolyticC761 VCKYPA2HB101K+ AB R
100p 500V CeramicC763 VCEA0A1HW105M+ AB R 1 50V ElectrolyticC764
VCKYPA2HB101K+ AB R 100p 500V CeramicC767 VCKYCY1HB153KY AA R 0.18
50V Ceramic
! C772 RC-KZ016SCEZZ AD R 470p 250V CeramicC768 VCKYCY1HB104KY
AA R 0.1 50V CeramicC769 VCQYTA1HM683J+ R 0.068 50VC904
VCKYCY1AB105KY AB R 1 10V CeramicC907 VCEA0A1HW106M+ AB R 10 50V
ElectrolyticC911 VCKYCY1AB105KY AB R 1 10V CeramicC922
VCKYCY1HB183KY AA R 0.018 50V CeramicC923 VCKYCY1HB183KY AA R 0.018
50V CeramicC928 VCE9GA1CW106M+ AB R 10 16V ElectrolyticC930
VCE9GA1CW106M+ AB R 10 16V ElectrolyticC931 VCEA0A1CW477M+ AC R 470
16V ElectrolyticC934 VCEA0A1HW105M+ AB R 1 50V ElectrolyticC935
VCEA0A1HW105M+ AB R 1 50V ElectrolyticC939 VCEA0A1CW227M+ AC R 220
16V ElectrolyticC942 VCEA0A1HW106M+ AB R 10 50V ElectrolyticC952
VCCCCY1HH681JY AB R 680p 50V CeramicC953 VCCCCY1HH681JY AB R 680p
50V CeramicC959 VCCCCY1HH681JY AB R 680p 50V CeramicC960
VCCCCY1HH681JY AB R 680p 50V CeramicC963 VCEA0A1HW106M+ AB R 10 50V
ElectrolyticC965 VCKYCY1HB103KY AA R 0.01 50V Ceramic
C2003 VCEA0A1AW108M+ AD R 1000 10V ElectrolyticC2004
VCEA0A1AW107M+ AC R 100 10V ElectrolyticC2005 VCKYCY1CB104KY AA R
0.1 50V CeramicC2006 VCKYCY1CB104KY AA R 0.1 50V CeramicC2007
VCKYCY1CB104KY AA R 0.1 50V CeramicC2008 VCKYCY1AB474KY AB R 0.47
10V CeramicC2009 VCEA0A1AW477M+ AD R 470 10V ElectrolyticC2010
VCKYCY1HB104KY AA R 0.1 50V CeramicC2011 VCEA9M1CW107M+ AB R 100
16V ElectrolyticC2012 VCKYCY1HB102KY AA R 1000p 50V CeramicC2013
VCCCCY1HH7R0DY AA R 7p 50V CeramicC2014 VCCCCY1HH7R0DY AA R 7p 50V
CeramicC2017 VCKYCY1CF224ZY AB R 0.22 16V CeramicC2018
VCKYCY1HB104KY AA R 0.1 50V CeramicC2019 VCEA9M1CW107M+ AB R 100
16V Electrolytic
[3] MAIN UNIT
4
-
29L-FG1L
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
C2020 VCKYCY1HB104KY AA R 0.1 50V CeramicC2021 VCEA9M1CW107M+ AB
R 100 16V ElectrolyticC2022 VCKYCY1CF224ZY AB R 0.22 16V
CeramicC2023 VCKYCY1CF224ZY AB R 0.22 16V CeramicC2025
VCKYCY1CF224ZY AB R 0.22 16V CeramicC2026 VCKYCY1HB104KY AA R 0.1
50V CeramicC2027 VCEA0A1CW107M+ AC R 100 16V ElectrolyticC2028
VCKYCY1CF224ZY AB R 0.22 16V CeramicC2029 VCKYCY1CF224ZY AB R 0.22
16V CeramicC2030 VCKYCY1CF224ZY AB R 0.22 16V CeramicC2032
VCEA0A0JW106M+ AB R 10 6.3V ElectrolyticC2034 VCFYFA1HA224J+ AB R
0.22 50VC2036 VCKYCY1CF224ZY AB R 0.22 16V CeramicC2037
VCCCCY1HH220JY AB R 22p 50V CeramicC2039 VCKYCY1CF334ZY AB R 0.33
16V CeramicC2040 VCEA0A1CW107M+ AC R 100 16V ElectrolyticC2041
VCKYCY1HB104KY AA R 0.1 50V CeramicC2046 VCEA0A1AW107M+ AC R 100
10V ElectrolyticC2047 VCKYCY1HB104KY AA R 0.1 50V CeramicC2048
VCKYCY1CB104KY AA R 0.1 50V CeramicC2100 VCEA0A1CW226M+ AB R 22 16V
ElectrolyticC2101 VCKYCY1CF334ZY AB R 0.33 16V CeramicC4001
VCEA0A1VW476M+ AC R 47 35V ElectrolyticC4002 VCKYCY1HB103KY AA R
0.01 50V CeramicC4913 VCKYPA1HB102K+ AA R 1000p 50V CeramicC4916
VCKYPA1HB102K+ AA R 1000p 50V CeramicC4922 VCEA0A1HW106M+ AB R 10
50V ElectrolyticC4924 VCEA0A1HW106M+ AB R 10 50V Electrolytic
RJ51 VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ52 VRS-CY1JF000JY
AA R 0 1/16W Metal OxideRJ53 VRS-CY1JF000JY AA R 0 1/16W Metal
OxideRJ54 VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ55
VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ56 VRS-CY1JF000JY AA R 0
1/16W Metal OxideRJ58 VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ59
VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ60 VRS-CY1JF000JY AA R 0
1/16W Metal OxideRJ61 VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ62
VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ64 VRS-CY1JF000JY AA R 0
1/16W Metal OxideRJ65 VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ66
VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ67 VRS-CY1JF000JY AA R 0
1/16W Metal OxideRJ74 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
RJ191 VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ280
VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ703 VRS-CY1JF000JY AA R 0
1/16W Metal OxideRJ704 VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ707
VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ708 VRS-CY1JF000JY AA R 0
1/16W Metal OxideRJ709 VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ710
VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ713 VRS-CY1JF000JY AA R 0
1/16W Metal OxideRJ715 VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ716
VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ717 VRS-CY1JF000JY AA R 0
1/16W Metal OxideRJ956 VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ957
VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
R51 VRS-CY1JF000JY AA R 0 1/16W Metal OxideR52 VRS-CY1JF103JY AA
R 10k 1/16W Metal OxideR53 VRS-CY1JF563JY AA R 56k 1/16W Metal
OxideR54 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR55
VRS-CY1JF101JY AA R 100 1/16W Metal Oxide
R103 VRS-RG3DB123J+ AA R 12k 2W Metal OxideR205 VRS-CY1JF471JY
AA R 470 1/16W Metal OxideR206 VRS-CY1JF392JY AA R 3.9k 1/16W Metal
OxideR207 VRS-CY1JF272JY AA R 2.7k 1/16W Metal OxideR208
VRS-CY1JF101JY AA R 100 1/16W Metal OxideR210 VRD-RA2BE122JY AA R
1.2k 1/8W CarbonR211 VRS-CY1JF000JY AA R 0 1/16W Metal OxideR221
VRS-CY1JF181JY AA R 180 1/16W Metal OxideR227 VRS-CY1JF680JY AA R
68 1/16W Metal OxideR228 VRS-CY1JF102JY AA R 1k 1/16W Metal
OxideR230 VRS-CY1JF391JY AA R 390 1/16W Metal OxideR238
VRS-CY1JF473JY AA R 47k 1/16W Metal OxideR239 VRD-RA2BE102JY AA R
1k 1/8W CarbonR241 VRS-CY1JF473JY AA R 47k 1/16W Metal OxideR307
VRS-CY1JF152JY AA R 1.5k 1/16W Metal OxideR308 VRS-CY1JF682JY AA R
6.8k 1/16W Metal OxideR309 VRS-CY1JF123JY AA R 12k 1/16W Metal
OxideR310 VRS-CY1JF473JY AA R 47k 1/16W Metal OxideR311
VRS-CY1JF272JY AA R 2.7k 1/16W Metal OxideR314 VRS-CY1JF682JY AA R
6.8k 1/16W Metal OxideR315 VRS-CY1JF152JY AA R 1.5k 1/16W Metal
OxideR317 VRD-RA2BE221JY AA R 220 1/8W Carbon
[3] MAIN UNIT
5
-
29L-FG1L
PRICE NEW PART DELIVERY
NO. PARTS CODE RANK MARK DESCRIPTION
R318 VRD-RA2BE221JY AA R 220 1/8W CarbonR319 VRS-CY1JF103JY AA R
10k 1/16W Metal OxideR321 VRS-CY1JF104JY AA R 100k 1/16W Metal
OxideR323 VRD-RA2BE102JY AA R 1k 1/8W CarbonR324 VRD-RA2BE183JY AA
R 18k 1/8W CarbonR325 VRD-RA2BE153JY AA R 15k 1/8W CarbonR335
VRD-RM2HD1R0JY AA R 1 1/2W CarbonR336 VRD-RM2HD1R0JY AA R 1 1/2W
CarbonR347 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR348
VRS-CY1JF101JY AA R 100 1/16W Metal OxideR351 VRS-CY1JF104JY AA R
100k 1/16W Metal OxideR352 VRS-CY1JF104JY AA R 100k 1/16W Metal
OxideR375 VRD-RA2BE102JY AA R 1k 1/8W CarbonR376 VRD-RA2BE102JY AA
R 1k 1/8W CarbonR391 VRN-RL3DBR10J+ AA R 0.10 2W Metal FilmR501
VRS-RG3AB221J+ AA R 220 1W Metal FilmR502 VRN-RL3DB5R6J+ AB R 5.6
2W Metal OxideR503 VRS-RG3DB271J+ AB R 270 2W Metal OxideR504
VRS-RG3DB561J+ AB R 560 2W Metal OxideR505 VRN-RA2BK182FY AB R 1.8k
1/8W CarbonR506 VRN-RL3DB1R0J+ AB R 1 2W Metal OxideR507
VRN-RA2BK182FY AB R 1.8k 1/8W CarbonR508 VRD-RA2BE103JY AA R 10k
1/8W CarbonR509 VRD-RA2BE222JY AA R 2.2k 1/8W CarbonR518
VRD-RA2BE101JY AA R 100 1/8W CarbonR519 VRD-RA2BE101JY AA R 100
1/8W CarbonR520 VRD-RA2BE101JY AA R 100 1/8W CarbonR521
VRS-CY1JF123JY AA R 12k 1/16W Metal OxideR600 VRS-CY1JF393FY AA R
39k 1/16W Metal OxideR602 VRS-RG2HC270J+ AA R 27 1/2W Metal
oxide
! R604 VRN-RL3AB4R7J+ AA R 4.7 1W Metal Film! R605
VRD-RA2EE103JY AA R 10k 1/4W Carbon! R606 VRN-RL3ABR47J+ AA R 0.47
1W Metal Film! R607 VRD-RA2EE103JY AA R 10k 1/4W Carbon! R608
VRS-CY1JF393JY AA R 39k 1/16W Metal Oxide
R609 VRN-RL3DB6R8J+ AB R 6.8 2W Metal OxideR611 VRD-RM2HD332JY
AA R 3.3k 1/2W CarbonR612 VRD-RA2BE101JY AA R 100 1/8W CarbonR613
VRD-RA2BE103JY AA R 10k 1/8W CarbonR614 VRD-RM2HD124JY AA R 120k
1/2W CarbonR615 VRD-RM2HD124JY AA R 120k 1/2W CarbonR616
VRD-RM2HD123JY AA R 12k 1/2W CarbonR618 VRN-RL3ABR47J+ AA R 0.47 1W
Metal FilmR621 VRD-RM2HD220JY AA R 22 1/2W CarbonR622
VRD-RA2BE394JY AA R 390k 1/8W CarbonR623 VRS-RG2HC102J+ AA R 1k
1/2W Metal oxideR624 VRD-RA2BE394JY AA R 390k 1/8W CarbonR625
VRD-RA2BE394JY AA R 390k 1/8W CarbonR626 VRS-RG3AB562J+ AA R 5.6k
1W Metal FilmR627 VRS-CY1JF394JY AA R 390k 1/16W Metal OxideR628
VRW-KQ3NC1R2K AB R 1.2 7W Metal OxideR633 VRS-CY1JF331JY AA R 330
1/16W Metal OxideR634 VRS-CY1JF331JY AA R 330 1/16W Metal OxideR635
VRS-CY1JF102JY AA R 1k 1/16W Metal OxideR637 VRD-RA2BE563JY AA R
56k 1/8W CarbonR638 VRS-CY1JF473JY AA R 47k 1/16W Metal OxideR639
VRS-KA3NG272J AD R 2.7k 7W Metal OxideR640 VRS-CY1JF182JY AA R 1.8k
1/16W Metal OxideR643 VRN-RL3LB3R3J+ AB R 3.3 2W Metal OxideR645
VRN-RA2BK473FY AA R 47k 1/8W CarbonR652 VRS-CY1JF102JY AA R 1k
1/16W Metal OxideR654 VRS-RG3DB103J+ AB R 10k 2W Metal OxideR657
VRS-KA3HG681J AD R 680 5W Metal OxideR671 VRD-RA2BE101JY AA R 100
1/8W CarbonR701 VRD-RA2BE220JY AA R 22 1/8W CarbonR703
VRD-RA2BE332JY AA R 3.3k 1/8W CarbonR704 VRD-RA2BE221JY AA R 220
1/8W CarbonR705 QJUM-0001AJFWY R JumperR707 VRS-VV3DB104J AB R 100k
2W Metal OxideR708 VRD-RA2BE683JY AA R 68k 1/8W Carbon
! R712 RR-HZ0014GEZZY AE R 12 1R713 VRD-RA2BE222JY AA R 2.2k
1/8W CarbonR714 VRD-RA2BE393JY AA R 39k 1/8W CarbonR715
VRS-CY1JF473JY AA R 47k 1/16W Metal OxideR717 VRS-RG3DB104J+ AB R
100k 2W Metal OxideR718 VRN-RA2BK124FY AA R 120k 1/8W CarbonR719
VRN-RA2BK563FY AA R 56k 1/8W CarbonR721 VRN-RA2BK124FY AA R 1.8k
1/8W CarbonR722 VRN-RA2BK562FY AA R 5.2k 1/8W CarbonR760
VRD-RA2BE102JY AA R 1k 1/8W CarbonR761 VRS-CY1JF103JY AA R 10k
1/16W Metal OxideR763 VRD-RA2BE470JY AA R 47 1/8W CarbonR766
VRD-RA2BE100JY AA R 100 1/8W CarbonR768 VRD-RA2EE182JY AA R 1.8k
1/4W CarbonR769 VRD-RA2BE122JY AA R 1.2k 1/8W Carbon
[3] MAIN UNIT
6
-
29L-FG1L
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
R905 VRD-RA2BE101JY AA R 100 1/8W CarbonR906 VRD-RA2BE101JY AA R
100 1/8W CarbonR907 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR909
VRS-CY1JF101JY AA R 100 1/16W Metal OxideR910 VRD-RA2BE101JY AA R
100 1/8W CarbonR911 VRS-CY1JF750JY AA R 75 1/16W Metal OxideR913
VRS-CY1JF101JY AA R 100 1/16W Metal OxideR915 VRS-CY1JF472JY AA R
4.7k 1/16W Metal OxideR917 VRS-CY1JF103JY AA R 10k 1/16W Metal
OxideR918 VRS-CY1JF103JY AA R 10k 1/16W Metal OxideR919
VRS-CY1JF472JY AA R 4.7k 1/16W Metal OxideR930 VRD-RA2BE750JY AA R
75 1/8W CarbonR931 VRD-RA2BE750JY AA R 75 1/8W CarbonR932
VRD-RA2BE750JY AA R 75 1/8W CarbonR933 VRD-RA2BE750JY AA R 75 1/8W
CarbonR935 VRS-CY1JF104JY AA R 100k 1/16W Metal OxideR938
VRD-RA2BE101JY AA R 100 1/8W CarbonR944 VRD-RA2BE101JY AA R 100
1/8W CarbonR945 VRS-CY1JF473JY AA R 47k 1/16W Metal OxideR947
VRS-CY1JF561JY AA R 560 1/16W Metal OxideR948 VRS-CY1JF473JY AA R
47k 1/16W Metal OxideR949 VRD-RA2BE561JY AA R 560 1/8W CarbonR950
VRS-CY1JF102JY AA R 1k 1/16W Metal OxideR952 VRS-CY1JF102JY AA R 1k
1/16W Metal OxideR956 VRD-RA2BE560JY AA R 56 1/8W CarbonR957
VRD-RA2BE331JY AA R 330 1/8W CarbonR959 VRS-CY1JF223JY AA R 22k
1/16W Metal OxideR960 VRD-RA2BE331JY AA R 330 1/8W CarbonR962
VRD-RA2BE102JY AA R 1k 1/8W CarbonR963 VRS-CY1JF101JY AA R 100
1/16W Metal OxideR964 VRD-RA2BE123JY AA R 12k 1/8W CarbonR965
VRS-CY1JF101JY AA R 100 1/16W Metal OxideR967 VRS-CY1JF333JY AA R
33k 1/16W Metal OxideR972 VRD-RA2BE333JY AA R 33k 1/8W CarbonR978
VRS-CY1JF104JY AA R 100k 1/16W Metal OxideR979 VRS-CY1JF104JY AA R
100k 1/16W Metal Oxide
R1032 VRD-RA2BE122JY AA R 1.2k 1/8W CarbonR1034 VRD-RA2BE122JY
AA R 1.2k 1/8W CarbonR2001 VRD-RA2BE103JY AA R 10k 1/8W CarbonR2003
VRD-RA2BE101JY AA R 100 1/8W CarbonR2004 VRD-RA2BE332JY AA R 3.3k
1/8W CarbonR2005 VRD-RA2BE101JY AA R 100 1/8W CarbonR2006
VRD-RA2BE101JY AA R 100 1/8W CarbonR2007 VRS-CY1JF222JY AA R 2.2k
1/16W Metal OxideR2008 VRS-CY1JF101JY AA R 100 1/16W Metal
OxideR2009 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR2010
VRS-CY1JF101JY AA R 100 1/16W Metal OxideR2011 VRD-RA2BE101JY AA R
100 1/8W CarbonR2012 VRD-RA2BE101JY AA R 100 1/8W CarbonR2014
VRD-RA2BE562JY AA R 5.6k 1/8W CarbonR2017 VRD-RA2BE102JY AA R 1k
1/8W CarbonR2019 VRD-RA2BE101JY AA R 100 1/8W CarbonR2023
VRD-RA2BE101JY AA R 100 1/8W CarbonR2024 VRD-RA2BE101JY AA R 100
1/8W CarbonR2025 VRD-RA2BE101JY AA R 100 1/8W CarbonR2026
VRD-RA2BE101JY AA R 100 1/8W CarbonR2027 VRS-CY1JF103JY AA R 10k
1/16W Metal OxideR2028 VRD-RA2BE101JY AA R 100 1/8W CarbonR2029
VRD-RA2BE101JY AA R 100 1/8W CarbonR2030 VRD-RA2BE101JY AA R 100
1/8W CarbonR2032 VRS-CY1JF824JY AA R 820k 1/16W Metal OxideR2033
VRD-RA2BE334JY AA R 330k 1/8W CarbonR2034 VRS-CY1JF101JY AA R 100
1/16W Metal OxideR2035 VRD-RA2BE101JY AA R 100 1/8W CarbonR2037
VRS-CY1JF101JY AA R 100 1/16W Metal OxideR2039 VRS-CY1JF101JY AA R
100 1/16W Metal OxideR2040 VRS-CY1JF101JY AA R 100 1/16W Metal
OxideR2042 VRS-CY1JF332JY AA R 3.3k 1/16W Metal OxideR2052
VRS-CY1JF332JY AA R 3.3k 1/16W Metal OxideR2101 VRS-CY1JF393JY AA R
39k 1/16W Metal OxideR2102 VRS-CY1JF563JY AA R 56k 1/16W Metal
OxideR2103 VRS-CY1JF563JY AA R 56k 1/16W Metal OxideR2104
VRS-CY1JF472JY AA R 4.7k 1/16W Metal OxideR2105 VRS-CY1JF472JY AA R
4.7k 1/16W Metal OxideR2106 VRS-CY1JF393JY AA R 39k 1/16W Metal
OxideR2107 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR4001
VRS-CY1JF221JY AA R 220 1/16W Metal OxideR4002 VRS-CY1JF331JY AA R
330 1/16W Metal OxideR4003 VRS-CY1JF681JY AA R 680 1/16W Metal
OxideR4004 VRS-CY1JF152JY AA R 1.5k 1/16W Metal OxideR4005
VRS-CY1JF222JY AA R 2.2k 1/16W Metal OxideR4006 VRS-CY1JF152JY AA R
1.5k 1/16W Metal OxideR4011 VRD-RA2BE101JY AA R 100 1/8W
CarbonR4012 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR4022
VRD-RA2BE223JY AA R 22k 1/8W Carbon
[3] MAIN UNIT
7
-
29L-FG1L
PRICE NEW PART DELIVERY
NO. PARTS CODE RANK MARK DESCRIPTION
R4023 VRS-CY1JF103JY AA R 10k 1/16W Metal OxideR4024
VRS-CY1JF473JY AA R 47k 1/16W Metal OxideR4025 VRS-CY1JF472JY AA R
4.7k 1/16W Metal OxideR4033 VRD-RA2BE181JY AA R 180 1/8W
CarbonR4911 VRS-CY1JF472JY AA R 4.7k 1/16W Metal OxideR4912
VRS-CY1JF103JY AA R 10k 1/16W Metal OxideR4913 VRS-CY1JF472JY AA R
4.7k 1/16W Metal OxideR4914 VRS-CY1JF103JY AA R 10k 1/16W Metal
OxideR5021 VRS-CY1JF181JY AA R 180 1/16W Metal OxideR5026
VRS-CY1JF331JY AA R 330 1/16W Metal OxideS4001 QSW-K0079GEZZ+ AB R
Switch , MENUS4002 QSW-K0079GEZZ+ AB R Switch , VOL UPS4003
QSW-K0079GEZZ+ AB R Switch , CH DOWNS4004 QSW-K0079GEZZ+ AB R
Switch , CH UPS4005 QSW-K0079GEZZ+ AB R Switch , VOL DOWNS4701
QSW-PA006WJZZ AG R Switch , POWERFB501 RBLN-0047CEZZY AB R Ferritte
BeadFB502 RBLN-0047CEZZY AB R Ferritte Bead
! FB601 RBLN-0047CEZZY AB R Ferritte BeadFB602 RBLN-0047CEZZY AB
R Ferritte BeadFB603 RBLN-A203WJZZ+ AB R Ferritte BeadFB700
RBLN-0036CEZZY AB R Ferritte BeadFB703 RBLN-A203WJZZ+ AB R Ferritte
BeadFB705 RBLN-A203WJZZ+ AB R Ferritte BeadFB751 RBLN-0047CEZZY AB
R Ferritte BeadFB752 RBLN-A034WJZZY AA R Ferritte Bead
FH4701 QFSHD1013CEZZ+ AC R Fuse HolderFH4702 QFSHD1014CEZZ+ AC R
Fuse Holder
F4701 QFS-CA003WJZZ AC R Fuse , 5A , 250VJ1 VW7UGB6-060KK R
JumperJ5 QCNW-F070WJPZ R FBT GND TO CRTJ6 QCNW-F071WJPZ R TUNER -
CRT GND
J352 QJAKJ0101SEZZ AE R HP JackJ905 QTANJA088WJZZ AG R
Terminal
J4901 QJAKGA023WJZZ AE R Front AV JackP301 QPLGNA109WJZZ AB R
Plug , 4pin
! P601 QPLGN0160FJZZ AD R Plug , 5pin (K)P701 QPLGN0260CEZZ AC R
Plug , 2pin
P2100 QPLGN0661CEZZ AD R Plug , 6pinP2101 QPLGN0661CEZZ AD R
Plug , 6pinP4701 QPLGN0269GEZZ AB R Plug , 2pin (AC)
RDA301 PRDARA287WJFW AH R Heat Sink for IC301RDA501
PRDARA288WJFW AG R Heat Sink for IC501RDA602 PRDARA123WJPW AF R
Heat Sink for Q602RDA604 PRDARA113WJPW AF R Heat Sink for Q604
! RDA701 PRDARA286WJFW AG R Heat Sink for IC701RDA755
PRDARA181WJFW AC R Heat Sink for D755
! RY701 RRLYJ0089CEZZ AG R RelayTP53 QLUGP0102PEZZ AA R Lug
[4] CRT UNITIC851 VHITDA6107A-1 AK R TDA6107AJF/N1D851
RH-DX0443CEZZY AB R DX0443CED852 RH-DX0443CEZZY AB R DX0443CED853
RH-DX0443CEZZY AB R DX0443CEC851 VCFYSB2EB823J AD R 0.082 250VC852
VCEA0A2EW106M+ AD R 10 250V ElectrolyticC854 RC-KZ018JCEZZ AC R
0.01 AC250/CeramicC856 VCKYPA2HB102K+ AA R 1000p 500V CeramicC861
VCKYPA2HB102K+ AA R 1000p 500V CeramicC862 VCKYPA2HB561K+ AA R 560p
500V CeramicR851 VRD-RM2HD391JY AA R 390 1/2W CarbonR852
VRD-RM2HD391JY AA R 390 1/2W CarbonR853 VRD-RM2HD391JY AA R 390
1/2W CarbonR854 VRC-MA2HG152KY AA R 1.5k 1/2W SolidR855
VRC-MA2HG152KY AA R 1.5k 1/2W SolidR856 VRC-MA2HG152KY AA R 1.5k
1/2W SolidR861 VRD-RM2HD224JY AA R 220k 1/2W CarbonR862
VRD-RA2BE101JY AA R 100 1/8W CarbonR863 VRD-RA2BE221JY AA R 220
1/8W CarbonR864 VRD-RA2BE221JY AA R 220 1/8W CarbonR865
VRD-RA2BE221JY AA R 220 1/8W CarbonR858 VRS-RG2HC100J+ AA R 10 1/2W
Metal OxideL850 RCILP0179CEZZ+ R Filter
FB852 RBLN-A034WJZZY AA R Ferrite BeadP851 QTIPM0083CEZZ AB R
TipP852 QTIPM0083CEZZ AB R Tip
RDA851 PRDAR0248PEFW AF R Heat Sink , IC851! SC851 QSOCVA024WJZZ
R Socket 12pin
[3] MAIN UNIT
8
-
29L-FG1L
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
[5] MISCELLANEOUS PARTS! QACCZA079WJPZ R AC Cord
VSP0080PA018A R SpeakerQCNW-E040WJPZ R SP WireQCNW-F147WJPZ R H
WireQCNW-F148WJPZ R KY Wire
[6] ACCESSORIES PARTSTINS-D173WJZZ R Operation
ManualRRMCGA561WJSA R Remote Control UnitUBATU0247AJZZ R
Battery
9
-
29L-FG1L
[7] CABINET PARTS
NO. PARTS CODE PRICE RANKNEW
MARKPART
DELIVERY DESCRIPTION
[7] CABINET PARTS1 CCABAB827WEV0 R Front Cabinet Ass'y
1-1 Not Available - - Front Cabinet1-2 JBTN-A679WJSA - R Power
Button1-3 MSPRCA040WJFW AB R Power Button Spring1-4 GCOVAB487WJSA -
R R/C & LED Cover1-5 GDORFA175WJSD - R Door1-6 HINDPC462WJZZ R
Indication Plate1-7 PSPAGA026WJZZ AB R Door Rubber1-8 MSPRPA031WJFW
AB R Door Spring1-9 HBDGB3141CESA AG R Sharp Badge
2 CCABBA718WEV1 BN R Rear Cabinet Ass'y2-1 Not Available - -
Rear Cabinet
10
-
29L-FG1L
[8] PACKING PARTS ( NOT REPLACEMENT PART )
NO. PARTS CODE PRICE RANKNEW
MARKPART
DELIVERY DESCRIPTION
[8] PACKING PARTS ( NOT REPLACEMENT PART )3 SPAKCD557WJZZ - -
Packing Case4 SSAKHA023WJZZ - - Wrapping Sack5 SPAKXA971WJZZ - -
Buffer Material Top6 SPAKXA972WJZZ - - Buffer Material Bottom7
SPAKXA973WJZZ - - Buffer Material Rear8 SSAKA0001PEZZ - -
Polyethylene Bag
*
* Wrapping Sack
* Packing Case
3 SPAKCD557WJZZ
*Polyethylene Bag
8 SSAKA0001PEZZ
Operation ManualBatteries
SSAKHA023