0003030A:99901203: 1999 Model 3030A LoadStar Commercial Fleet Body Section 1 BODY SPECIFICATIONS Section 2 REPLACEMENT PARTS IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA 50438-0189 TEL: 515-923-3711 TECHNICAL SUPPORT FAX: 515-923-2424 MANUAL PART NO: 99901203 PARTS AND SPECIFICATIONS 20000114
40
Embed
1999 Model 3030A LoadStar Commercial Fleet Body · 10/20/2017 · 1999 Model 3030A LoadStar Commercial Fleet Body GENERAL SPECIFICATIONS STANDARD CHASSIS CAB-TO-AXLE (CA) 84" 213.4
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
0003030A:99901203: i
1999 Model 3030A LoadStarCommercial Fleet Body
Section 1 BODY SPECIFICATIONSSection 2 REPLACEMENT PARTS
IOWA MOLD TOOLING CO., INC.BOX 189, GARNER, IA 50438-0189
TEL: 515-923-3711TECHNICAL SUPPORT FAX: 515-923-2424
MANUAL PART NO: 99901203
PARTS AND SPECIFICATIONS
20000114
0003030A:99901203: ii
PARTS ORDERING INFORMATION19980401
Before placing an order, take the time to record the following information. This information should thenbe given to an IMT representative when placing your order.
BODY MODEL NUMBER:
BODY SERIAL NUMBER:
PART NUMBER, DESCRIPTION AND QUANTITY REQUIRED:
If left or right side is applicable, please specify.
Contact IMT at the following address:
IOWA MOLD TOOLING CO., INC.BOX 189, GARNER, IA 50438-0189TEL: 515-923-3711PRODUCT SUPPORT FAX: 515-923-2424
See Series 60 Compressor Manualfor complete installation and operation instructions.
0003030A:99901203: iii19980401
LIMITED WARRANTYWARRANTY COVERAGE - Products manufactured by IowaMold Tooling Co., Inc. (IMT) are warranted to be free from de-fects in material and workmanship, under proper use, applicationand maintenance in accordance with IMT�s written recommenda-tions, instructions and specifications as follows:
1. Ninety (90) days; labor on IMT workmanship from the date ofshipment to the end user.
2. One (1) year; original IMT parts from the date of shipment tothe end user.
IMT�s obligation under this warranty is limited to, and the soleremedy for any such defect shall be the repair or replacement (atIMT�s option) of unaltered parts returned to IMT, freight prepaid,and proven to have such defect, provided such defect occurs withinthe above stated warranty period and is reported within fourteen(14) days of its occurence.
IMPLIED WARRANTY EXCLUDED - This is the only autho-rized IMT warranty and is in lieu of all other express or impliedwarranties or representations, including any implied warranties ofmerchantability or fitness for any particular purpose or of any otherobligations on the part of IMT.
ITEMS EXCLUDED - The manufacturer gives no warranty onany components purchased by the manufacturer, and such compo-nents as are covered only by the warranties of their respectivemanufacturers.
WARRANTY CLAIMS - Warranty claims must be submitted andshall be processed in accordance with IMT�s established warrantyclaim procedure.
WARRANTY SERVICE - Warranty service will be performed byany IMT distributor authorized to sell new IMT products of thetype involved or by any IMT Service Center authorized to servicethe type of product involved or by IMT in the event of direct salesmade by IMT. At the time of requesting warranty service, thepurchaser must present evidence of the date of delivery of the prod-uct. The purchaser shall pay any premium for overtime labor re-quested by the purchaser, any charge for making service calls andfor transporting the equipment to the place where warranty workis performed.
WARRANTY VOIDED - All obligations of IMT under this war-ranty shall be terminated:(1) if service other than normal mainte-nance or normal replacement of service items is performed by some-one other than an authorized IMT dealer, (2) if product is modi-fied or altered in ways not approved by IMT.
PURCHASER�S RESPONSIBILITY - This warranty covers onlydefective material and workmanship. It does not cover deprecia-tion or damage caused by normal wear, accident, improper protec-tion in storage, or improper use. The purchaser has the obligationof performing the care and maintenance duties discussed in IMT�swritten recommendations, instructions and specifications. Anydamage which results because of purchaser�s failure to performsuch duties shall not be covered by this warranty. The cost ofnormal maintenance and normal replacement of service items suchas filters, belts, etc. shall be paid by the purchaser.
CONSEQUENTIAL DAMAGES - The only remedies the pur-chaser has in connection with the breach or performance of anywarranty on IMT products are those set forth above. In no eventwill the dealer, IMT or any company affiliated with IMT, be liablefor business interruptions, loss of sales and/or profits, rental orsubstitute equipment, costs of delay or for any other special, indi-rect, incidental or consequential losses, costs or damages.
REPRESENTATIONS EXCLUDED - IMT products are subjectto no expressed, implied or statutory warranty other than hereinset forth, and no agent, representative or distributor of the manu-facturer has any authority to alter the terms of this warranty in anyway whatsoever or to make any representations or promises, ex-press or implied, as to the quality or performance of IMT productsother than those set forth above.
CHANGE IN DESIGN - IMT reserves the right to make changesin design or improvements upon its products without imposingany obligation upon itself to install the same upon its productstheretofore manufactured.
Effective January, 1985
This parts manual is provided to the user to assist in servicing the equipment. It is the propertyof Iowa Mold Tooling Co., Inc and,as such, may not be reproduced either whole or in part,whether by chemical, electrostatic, mechanical or photographic meanswithout the expressedwritten permission of an officer of Iowa Mold Tooling Co., Inc. One manual is provided with each piece ofnew equipment and additional manuals may be obtained at a nominal price.
IOWA MOLD TOOLING CO., INC.BOX 189, GARNER, IA 50438-0189
TEL: 515-923-3711TECHNICAL SUPPORT FAX: 515-923-2424
0003030A:99901203: iv19980401The information within this manual has been compiled and checked but errors do occur. To provide our customers with amethod of communicating those errors we have provided the Manual Change Request form below. In addition to errorreporting, you are encouraged to suggest changes or additions to the manual which would be of benefit to you. We cannotguarantee that these additions will be made but we do promise to consider them. When completing the form, please write orprint clearly. Submit a copy of the completed form to the address listed below.
0003030A:99901203: v19980401
TORQUE DATA CHARTFINE THREAD BOLTS COARSE THREAD BOLTS
When using the torque data in the charts above, the following rules should be observed.
1. Bolt manufacturer�s particular specifications should be consulted when provided.
2. Flat washers of equal strength must be used.
3. All torque measurements are given in foot-pounds. To convert to inch-pounds, multiply by 12.
4. Torque values specified are for bolts with residual oils or no special lubricants applied. If special lubricants of high stressability, such as Never-Seez compound graphite and oil, molybdenum disulphite, collodial copper or white lead are applied,multiply the torque values in the charts by the factor .90. The use of Loctite does not affect the torque values listed above.
5. Torque values for socket-head capscrews are the same as for Grade 8 capscrews.
WARNINGAnytime a gear-bearing bolt is removed, it must be replaced with a new bolt of the identical grade and size. Oncea bolt has been torqued to 75% of its proof load and then removed, the torque coefficient may no longer be thesame as when the bolt was new thus giving indeterminate clamp loads after torquing. Failure to replace gear-bearing bolts may result in bolt failure due to metal fatique causing serious injury or DEATH.
0003030A:99901203:
vi19990115
0003030A:99901203: 1-1
SECTION 1. SPECIFICATIONS19981209
GENERAL SPECIFICATIONS..................................................................................... 3
BODY CUBIC CAPACITY 344 cubic feet 9.74 cubic meters
TIRE HAULING CAPACITY Twenty-four 11R24.5 Twenty-four 11R24.5Two 33.25-29 Two 33.25-29
AVAILABLE PAYLOAD 6400 lbs 2903 kgs
LIFTGATE CAPACITY 1600 lbs 725 kgs
COMPARTMENT SPECIFICATIONSLEFT FRONT COMPARTMENT 20"H X 54"W X 20"D 50.8x137.2x50.8cm
12.50 cubic feet .35 cubic meters
RIGHT FRONT COMPARTMENT 20"H X 54"W X 20"D 50.8x137.2x50.8cm12.50 cubic feet .35 cubic meters
LEFT REAR COMPARTMENT 17"H X 32"W X 20"D 43.2x81.3x50.8cm6.30 cubic feet .18 cubic meters
RIGHT REAR COMPARTMENT 17"H X 32"W X 20"D 43.2x81.3x50.8cm6.30 cubic feet .18 cubic meters
Note: Dimensions of compartments are nominal.
IOWA MOLD TOOLING CO., INC.BOX 189, GARNER, IA 50438-0189
TEL: 515-923-3711TECHNICAL SUPPORT FAX: 515-923-2424
0003030A:99901203: 1-419980401
STANDARD FEATURES• 1/2” x 50’ hose reel.• 1/2” moisture separator/regulator/oiler.• Amber beacon light.• Two 12V floodlights.• Four compartment lights.• Back-up alarm.• An ICC safety kit.• Hour meter
OPTIONAL EQUIPMENT• Cab caddy.• 3/8" x 35' hose reel.• Commercial fleet tool package.• Dual 1/2" airline coupler plumbing.• 300-gallon portable calcium chloride skid.• Liftgate side rail and tire stop.• Two-bar fold-up tire inflation cage with body installed carrying bracket and 6' inflation hose.• Customer identification.
IMT reserves the right to change specifications and design without notice.
LEGENDA LH & RH FRONT UBTB 20”H x 54”W x 20”DB DOOR OPENING 46.25”W x 16.25”HC LH & RH REAR UBTB 17”H x 32”W x 20”DD DOOR OPENING 24.25”W x 13.25”H
WARNINGThe installer of the driveline must inspect thefinal position of the driveline to determinewhether its location provides sufficient protectionto an operator, or other personnel, from hazardsassociated with a rotating driveline. If protectionis insufficient, the installation of a guard isrequired. If you are unsure of methods to guarda rotating driveline, call Iowa Mold Tooling Co.,Inc. for instructions. Failure to do so may resultin serious injury or death.