1997-Nissan-Quest

ForewordWelcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latesttechniques and strict quality control.

This manual was prepared to help you understand the operation and maintenance of your vehicle so that you may enjoy many miles ofdriving pleasure. Please read through this manual before operating your vehicle.

A separate Warranty Information and Maintenance Log Booklet explains details about the warranties covering your vehicle and vehiclemaintenance schedules.

Your NISSAN dealer knows your vehicle best. When you require any service or have any questions, he will be glad to assist you with theextensive resources available to him.

WARNING

IMPORTANT SAFETY INFORMATIONREMINDERS FOR SAFETY!Follow these five important driving rules to help ensure a safeand complete trip for you and your passengers:● NEVER drive under the influence of alcohol or drugs.● ALWAYS observe posted speed limits and never drive too

fast for conditions.● ALWAYS use your seat belts and appropriate child restraint

systems.● ALWAYS provide information about the proper use of

vehicle safety features to all occupants of the vehicle.● ALWAYS review this Owner’s Manual for important safety

information.

© 1996 NISSAN NORTH AMERICA, INC.TORRANCE, CALIFORNIA

All rights reserved. No part of this Owner’s Manual may be reproducedor stored in a retrieval system, or transmitted in any form, or by anymeans, electronic, mechanical, photocopying, recording or otherwise,without the prior written permission of Nissan North America, Inc.

NOTES ON THE INFORMATION CONTAINED INTHIS OWNER’S MANUALThis Owner’s Manual contains descriptions and operating in-structions for all systems, features and optional equipment thatmight appear in any model of this vehicle built for any destina-tion in North America, including the continental United States,Canada and Hawaii. Therefore, you may very well find informa-tion in this manual that does not apply to your vehicle.

MODIFICATION OF YOUR VEHICLEThis vehicle should not be modified. Modification couldaffect its performance, safety or durability, and may evenviolate governmental regulations. In addition, damage orperformance problems resulting from modifications maynot be covered under NISSAN warranties.

All information, specifications and illustrations in this manual are thosein effect at the time of printing. NISSAN reserves the right to changespecifications or design without notice and without obligation.

The inside pages of this manual containa minimum of 50% recycled fibers,including 10% post-consumer fibers.

Welcome To The World Of NISSAN

Your new Nissan is the result of our dedication toproduce the finest in safe, reliable and economi-cal transportation. Your vehicle is the product ofa successful worldwide company that manufac-tures cars and trucks in over 17 countries anddistributes them in 170 nations.

Nissan vehicles are designed and manufacturedby Nissan Motor Co., Ltd. which was founded inTokyo, Japan in 1933, and Nissan affiliates world-wide, collectively growing to become the fifth larg-est automaker in the world. In addition to cars andtrucks, Nissan also makes textile machinery, forklifttrucks, marine engines, boats and other products.

Nissan has made a substantial and growinginvestment in North America, starting with theopening of Nissan Motor Corporation U.S.A. in1960 and continuing with the production of somecars and trucks at one of the world’s mostmodern manufacturing facilities, Nissan Motor

Manufacturing Corporation U.S.A. in Smyrna,Tennessee, vehicle styling at Nissan DesignInternational in San Diego, California, and engi-neering at Nissan Research and Development inFarmington Hills, Michigan.

Nissan Motor Corporation U.S.A. and its dealersemploy about 60,000 Americans.

Nissan is also a substantial contributor to theCanadian economy. Nissan Canada Inc., its sup-pliers and over 170 dealers employ approxi-mately 4,500 people. These include companyemployees and the staffs of Nissan dealers allacross Canada. In addition, many Canadianswork for companies that supply Nissan and Nis-san dealers with materials and services rangingfrom the operation of port facilities and transpor-tation services, to the supply of lubricants, partsand accessories.

Nissan pioneered the use of electronics andcomputers in automobiles, and has led the indus-try in improving both performance and fuel effi-ciency through new engine designs and the useof synthetic materials to reduce vehicle weight.The company has also developed ways to buildquality into its vehicles at each stage of theproduction process, both through extensive useof automation and — most importantly —through an awareness that people are the cen-tral element in quality control.

From the time the parts arrived from our suppli-ers until you took delivery of your new Nissan,dozens of checks were made to ensure that onlythe best job was being done in producing anddelivering your vehicle. Nissan also takes greatcare to ensure that when you take your Nissan toyour dealer for maintenance, the service techni-cian will perform his work according to the qualitystandards that have been established by thefactory.

Safety has also been built into your Nissan. Asyou know, seat belts are an integral part of thesafety systems that will help protect you and yourpassengers in the event of a sudden stop or anaccident. We urge you to use the belts every timeyou drive the vehicle.

The Nissan story of growth and achievementreflects our major goal: to provide you, ourcustomer, with a vehicle that is built with qualityand craftsmanship — a product that we can beproud to build and you can be proud to own.

AFW0001

The inside pages of this manual containa minimum of 50% recycled fibers,including 10% post-consumer fibers.

Z X

NISSAN CUSTOMER CARE PROGRAMNISSAN CARES ...

Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction withyour vehicle and your NISSAN dealer are our primary concerns. Your NISSAN dealer is always available to assistyou with all your automobile sales and service needs.

However, if there is something that your NISSANdealer cannot assist you with or you would like toprovide NISSAN directly with comments or questions,please contact our (NISSAN’s) Consumer Affairs De-partment using our toll-free number:

For U.S. mainland and Alaska customers1-800-NISSAN-1 (1-800-647-7261)

For Hawaii customers(808) 836-0888 (Oahu Number)

For Canada customers1-800-387-0122

The Consumer Affairs Department will ask for the following infor-mation:— Your name, address, and telephone number— Vehicle identification number (on dashboard)— Date of purchase— Current odometer reading— Your NISSAN dealer’s name— Your comments or questions

OR

you may write to NISSAN with the information on theleft at:

For U.S. mainland and Alaska customersNissan Motor Corporation U.S.A.Consumer Affairs DepartmentP.O. Box 191Gardena, California 90248-0191

For Hawaii customersNissan Motor Corporation in Hawaii2880 Kilihau St.Honolulu, Hawaii 96819

For Canada customersNissan Canada Inc.P.O. Box 1709, Station ‘‘B’’Mississauga, Ontario L4Y 4H6

We appreciate your interest in NISSAN and thank you for buying a quality NISSAN vehicle.

Z X

You will see various symbols in this manual.They are used in the following ways:

WARNINGThis is used to indicate the presence ofa hazard that could cause death orserious personal injury. To avoid orreduce the risk, the procedures mustbe followed precisely.

CAUTIONThis is used to indicate the presence ofa hazard that could cause minor ormoderate personal injury or damage toyour vehicle. To avoid or reduce therisk, the procedures must be followedcarefully.

If you see this symbol, it means ‘‘Do not dothis’’ or ‘‘Do not let this happen.’’

APD0649

IMPORTANT INFORMATIONABOUT THIS MANUAL

Z X

Z X

Contents Instruments and controls

Pre-driving checks and adjustments

Heater, air conditioner and audio system

Starting and driving

In case of emergency

Appearance and interior care

Do-it-yourself operations

Maintenance schedule

Technical and consumer information

Index

1

2

3

4

5

6

7

8

9

10

1 Instruments and controls

Meters and gauges ................................................1-3Speedometer and odometer ..................................1-4Tachometer ............................................................1-4Engine coolant temperature gauge........................1-4Fuel gauge .............................................................1-5Warning/indicator lights and chimes ......................1-6Theft warning (if so equipped) .............................1-10Windshield wiper and washer switch...................1-11Rear window wiper and washer switches............1-12Rear window defogger switch..............................1-12Headlight control switch .......................................1-13Daytime running light system (for Canada) .........1-13Autolamp switch (if so equipped).........................1-13Turn signal switch .............................................1-14Cornering light ......................................................1-15Instrument brightness control...............................1-15Hazard warning flasher switch.............................1-15

Cigarette lighter (accessory) and ashtray............1-16Rear power point..................................................1-17Coin tray...............................................................1-17Compact disc and audio cassette storagecompartment.........................................................1-18Cup holder............................................................1-18Power window ......................................................1-19Automatic power window switch ..........................1-20Sunroof (if so equipped).......................................1-21Manual rear windows ...........................................1-22Power rear windows (if so equipped) ..................1-22Clock.....................................................................1-23Interior lights.........................................................1-24Luggage compartment lights................................1-24Personal reading light ..........................................1-24Spotlights..............................................................1-25

Z X

AIC0570

1-2

Z X

AIC0588

METERS AND GAUGES

1-3

Z X

SpeedometerThe speedometer indicates vehicle speed.

OdometerThe odometer records the total distance thevehicle has been driven.

Trip odometerThe trip odometer records the distance ofindividual trips. Before each trip, set the tripodometer to zero by pushing the RESETbutton.

The tachometer indicates engine speed inrevolutions per minute (RPM).

CAUTIONWhen engine speed approaches thered zone, shift to a higher gear. Oper-ating the engine in the red zone maycause serious engine damage.

This gauge indicates the engine coolanttemperature. The engine coolant tempera-ture varies with the outside air temperatureand driving conditions.

CAUTIONIf the gauge indicates engine coolanttemperature over the normal range,stop the vehicle as soon as safely pos-sible. If the engine is overheated, con-tinued operation of the vehicle mayseriously damage the engine. See the‘‘In case of emergency’’ section forimmediate action required.

AIC0003 AIC0110 AIC0004

SPEEDOMETER ANDODOMETER

TACHOMETER ENGINE COOLANTTEMPERATURE GAUGE

1-4

Z X

This gauge indicates the approximate fuellevel in the tank.

The gauge may move slightly during brak-ing, turning, acceleration, or going up ordown hills.

The gauge needle remains in approximatelythe same position even when the ignitionkey is turned OFF.

The low fuel warning light comes on whenthe amount of fuel in the tank is getting low.

Refill the fuel tank before the gaugeregisters E (empty).

AIC0005

FUEL GAUGE

1-5

Z X

Checking bulbsApply the parking brake, fasten seat belts,and turn the ignition key to ON without start-ing the engine. The following lights come onand stay on until the engine is started:

, , , or

The following lights come on briefly andthen go off:

ABS or , ,

If any light fails to come on, it mayindicate a burned-out bulb or an opencircuit in the electrical system. Have the

system repaired promptly.

Engine oil pressure warninglight

This light warns of low engine oil pressure. Ifthe light flickers or comes on during normaldriving, pull off the road in a safe area, stopthe engine immediately and call a NISSANdealer or other authorized repair shop.

The oil pressure warning light is notdesigned to indicate a low oil level. Usethe dipstick to check the oil level. See‘‘Engine oil’’ in the ‘‘Do-it-yourself opera-tions’’ section.

CAUTION

Running the engine with the oil pres-sure warning light on could cause seri-ous damage to the engine almost im-mediately. Turn off the engine as soonas it is safe to do so.

Charge warning lightIf the light comes on while the engine isrunning, it may indicate something wrongwith the charging system. Turn the engineoff and check the generator belt. If the belt isloose, broken, missing, or if the light re-

AIC0589

WARNING/INDICATORLIGHTS AND CHIMES

1-6

Z X

mains on, see your NISSAN dealer imme-diately.

CAUTION

Do not continue driving if the belt isloose, broken or missing.

Low fuel warning light

This light comes on when the fuel level inthe fuel tank is getting low. Refuel as soonas it is convenient, preferably before the fuelgauge reaches E. There should be a smallreserve of fuel in the tank when the fuelgauge needle reaches E.

Door ajar warning light

This light comes on when any of the doorsare not closed securely while the ignitionkey is ON.

Seat belt warning light andchime

The light and chime remind you to fastenyour seat belts. If the driver’s seat belt isNOT securely fastened when the ignitionkey is turned to ON or START, the chimesounds four times and the light illuminates.

Refer to ‘‘Seat belts’’ in the ‘‘Pre-drivingchecks and adjustments’’ section for pre-cautions on seat belt usage.

Supplemental air bagwarning light

When the ignition key is in the ON or STARTposition, the supplemental air bag warninglight illuminates for about 7 seconds andthen turns off. This means the Air BagSupplemental Restraint System is opera-tional.

If any of the following conditions occur, thesupplemental air bag system needs servic-ing and your vehicle should be taken to yournearest authorized NISSAN dealer as soonas practical:

1. The supplemental air bag warning lightdoes not come on for 7 seconds and thengo off as described above.

2. The supplemental air bag warning lightflashes intermittently or remains on.

3. The supplemental air bag warning lightdoes not come on at all.

Unless checked and repaired, the Air BagSupplemental Restraint System may notfunction properly. For additional details, see

‘‘Supplemental restraint system’’ in the ‘‘Pre-driving checks and adjustments’’ section.

WARNING

If the supplemental air bag warninglight is on, it could mean that thesupplemental air bag will not operate inan accident.

Low washer fluid warninglight

This light comes on when the washer res-ervoir fluid is at a low level. Add washer fluidas necessary. See the ‘‘Do-it-yourself op-erations’’ section.

Brake warning lightThis light functions for both the parkingbrake and the foot brake systems.

The light comes on when the parking brakeis applied, and also warns of a low brakefluid level. If the light comes on while theengine is running with the parking brake notapplied, stop the vehicle and perform thefollowing:

1. Check the brake fluid level. Add brakefluid as necessary. See ‘‘Brake fluid’’ in

1-7

Z X

the ‘‘Do-it-yourself operations’’ section.

2. If the brake fluid level is correct, have thewarning system checked by your NIS-SAN dealer.

WARNING

● Your brake system may not be work-ing properly if the warning light ison. Driving could be dangerous. Ifyou judge it to be safe, drive care-fully to the nearest service stationfor repairs. Otherwise, have your ve-hicle towed.

● Pressing the brake pedal with theengine stopped and/or low brakefluid level may increase your stop-ping distance and braking will re-quire greater pedal effort as well aspedal travel.

● If the brake fluid level is below theminimum mark on the brake fluidreservoir, do not drive until the brakesystem has been checked at a NIS-SAN dealer.

or ABS Anti-lock brakewarning light

If the light comes on while the engine isrunning, it may indicate something wrongwith the anti-lock portion of the brake sys-tem. Have the system checked by yourNISSAN dealer.

If an abnormality occurs in the system, theanti-lock function ceases, but the brakescontinue to operate normally.

If the light comes on while you are driv-ing, contact your NISSAN dealer for re-pair.

Overdrive off indicator light

This light comes on during driving when theoverdrive switch is pressed to prevent over-drive operation.

The O/D OFF indicator light comes on fortwo seconds each time the ignition key isturned ON. This shows the light is function-ing properly.

If the O/D OFF indicator light blinks forapproximately 8 seconds after coming on for2 seconds, have your NISSAN dealer checkthe transmission and repair it if necessary.

The automatic transmission is equippedwith an electronic Fail-Safe mode. This sys-tem allows the vehicle to be driven even inthe event of damage to the electrical cir-cuits. If this occurs, the gears automaticallyengage and lock into 3rd gear.

NOTE: See the ‘‘Fail-safe’’ section in the‘‘Starting and driving’’ section before visitingyour NISSAN dealer.

Turn signal/hazard indicatorlights

The appropriate light flashes when the turnsignal lever is activated.

Both lights flash when the hazard switch isturned on.

High beam indicator lightThis light comes on when the headlight highbeam is on and goes out when the lowbeam is selected.

Cruise indicator light

The light comes on while the vehicle speedis controlled by the cruise control system. Ifthe CRUISE indicator blinks, have the sys-tem checked by your NISSAN dealer.

1-8

Z X

Key reminder chime

The chime sounds if the driver’s or passen-ger’s door is opened while the key is left inthe ignition switch. Remove the key andtake it with you when leaving the vehicle.

Light reminder chime

A chime sounds when the driver’s or pas-senger’s door is opened if the headlightcontrol switch is turned on (ignition switch isturned OFF).

Turn the headlight control switch to OFFwhen you leave the vehicle.

Brake pad wear warning

The disc brake pads have audible wearwarnings. When a brake pad requires re-placement, it makes a high pitched scrapingsound when the vehicle is in motion whetheror not the brake pedal is depressed. Havethe brakes checked as soon as possible ifthe warning sound is heard.

or Malfunction indica-tor light (MIL)

If the malfunction indicator light comes onsteady or blinks while the engine is running,

it may indicate a potential emission controlproblem.

The malfunction indicator light will come onin one of two ways:

1. Malfunction indicator light on steady - Anemission control system malfunction hasbeen detected. Have the vehicle in-spected by an authorized NISSANdealer. You do not need to have yourvehicle towed to the dealer.

2. Malfunction indicator light blinking - Anengine misfire has been detected whichmay damage the emission control sys-tem. To reduce or avoid emission controlsystem damage:● do not drive at speeds above 45 MPH

(72 km/h).● avoid hard acceleration or decelera-

tion.● avoid steep uphill grades.● if possible, reduce the amount of cargo

being hauled or towed.

The malfunction indicator light may stopblinking and come on steady. Have thevehicle inspected by an authorized NISSANdealer. You do not need to have your ve-hicle towed to the dealer.

CAUTIONContinued vehicle operation withouthaving the emission control systemchecked and repaired as necessarycould lead to poor driveability, reducedfuel economy, and possible damage tothe emission control system, whichmay affect your warranty coverage.

Some conditions may cause the malfunc-tion indicator light to come on steady orblink. For example, running the vehicle outof fuel, which causes the engine to misfire,may cause the malfunction indicator light tocome on steady or blink.

If you suspect that you experienced such acondition, drive the vehicle to an authorizedNISSAN dealer and have the vehicle in-spected. Avoid any unnecessary diagnosisduring the service by informing the dealer ofthe condition that may have occurred.

1-9

Z X

The theft warning system provides audioand visual alarm signals if parts of thevehicle are disturbed.

How to activate the theft warningsystem

1. Close all windows.

2. Remove the key from the ignition switch.

3. Close all doors and the hood. Lock alldoors by pressing the button on themulti-remote controller. At this time, theparking lights blink and the horn chirps toindicate all doors are locked.

The system can be activated even if thewindows are open.

4. Confirm that the SECURITY indicatorlight, located under the hazard warningswitch, illuminates.

● The SECURITY light stays on for about30 seconds and then begins to flashonce every three seconds. The system isnow activated.

The theft warning system is NOT activated ifone of the following occurs:

● A door is unlocked or opened, the hood isopened, or the ignition key is turned tothe ACC or ON position during the 30seconds in which the SECURITY lightstays on.

● The SECURITY light blinks at a steady1/2 second on - 1/2 second off ratebecause a door or the hood is open andthe key is not in the ACC or ON position.When the ignition key is turned to theACC or ON position, the SECURITY lightturns off.

Theft warning system operation

The theft warning system emits the follow-ing alarm:

● The headlights and tail lights flash andthe horn sounds intermittently. In addi-tion, the starter motor does not operate.

● The alarm automatically turns off aftertwo to three minutes. However, the alarmreactivates if the vehicle is tampered withagain. The alarm can be shut off byunlocking a door with the key or bypressing the button on the multi-remote controller.

The alarm is activated when:

● a door is unlocked or opened withoutusing the key or the multi-remote control-ler. This includes unlocking the doorswith the inside door lock switch.

● the hood is opened.

● the ignition is placed into the ACC, ON,or START position without the key in theignition.

IC0005

THEFT WARNING(if so equipped)

1-10

Z X

How to stop the alarmThe alarm stops only by unlocking a doorwith the key or by pressing the button onthe multi-remote controller. The alarm doesnot stop if the ignition key is turned to theACC or ON position.

If the system does not operate as de-scribed above, have it checked by yourNISSAN dealer.

To operate the wipers intermittently, adjustthe knob between the S and F positions. Forcontinuous operation, select LO or HI.

To operate the washer, press on the end ofthe wiper knob. For more washer fluid, pushand hold the end of the wiper knob. Thewipers cycle a few times when the washer isactivated. The washer operates in any ofthe wiper positions.

CAUTIONThe following could damage thewasher system:

● Do not operate the washer continu-ously for more than 30 seconds.

● Do not operate the washer if thereservoir tank is empty.

WARNINGIn freezing temperatures the washersolution may freeze on the windshield

AIC0561 AIC0559

WINDSHIELD WIPER ANDWASHER SWITCH

1-11

Z X

and obscure your vision, which maylead to an accident. Warm the wind-shield with the defroster before youwash the windshield.

Push and hold the rear washer switch tooperate the rear washer. The wiper cyclescontinuously until the switch is released.

Push the rear wiper switch to operate thewiper. The wiper cycles intermittently. Pushagain to cancel.

CAUTION● Do not operate the washer continu-

ously for more than 30 seconds.

● Do not operate the washer if thereservoir tank is empty.

To defog the rear window glass, start theengine and push the switch on. The indica-tor light comes on. Push the switch again toturn the defogger off.The rear window defogger switch is alsoused to defrost, defog, or de-ice the poweroutside heated mirrors (if so equipped).It automatically turns off in approximately 15minutes.

CAUTIONWhen cleaning the inner side of thewindow, be careful not to scratch ordamage the rear window defogger.

AIC0572 AIC0573

REAR WINDOW WIPER ANDWASHER SWITCHES

REAR WINDOW DEFOGGERSWITCH

1-12

Z X

LightingTurn the dial to the position:

The front parking, side marker, tail, licenseplate and instrument lights come on.

Turn the dial to the position:

Headlights come on and all of the previouslylisted lights remain on.

To select the high beam, push the turnsignal lever away from you. The leverlatches in place. Pull it back to select the lowbeam.

DAYTIME RUNNING LIGHTSYSTEM (for Canada)The headlights automatically illuminate at areduced intensity when the engine is startedwith the parking brake released. The day-time running lights operate with the head-light switch in the OFF position or in the

position. Turn the headlight switch tothe position for full illumination whendriving at night.

If the parking brake is applied before theengine is started, the daytime running lightsdo not illuminate. The daytime running lightsilluminate once the parking brake is re-leased. The daytime running lights will re-main on until the ignition switch is turnedOFF.

WARNINGWhen the daytime light system is ac-tive, tail lights on your vehicle will notbe on. It is necessary at dusk to turn onyour headlights. Failure to do so couldcause an accident injuring yourself andothers.

The autolamp system allows the headlightsto be set so they turn on and off automati-cally. The autolamp system can turn on theheadlights automatically when it is dark,turn off the headlights when it is light, andkeep the headlights on for up to threeminutes after you turn the key to OFF.

To set the autolamp system:

1. Make sure the headlight switch is in theOFF position. If the headlight switch is inthe or position, the auto-lamp system is canceled.

2. Turn the ignition key to ON.

AIC0043 AIC0041

HEADLIGHT CONTROLSWITCH

AUTOLAMP SWITCH(if so equipped)

1-13

Z X

3. Use the autolamp switch to activate theautolamp feature. It is to the left of thesteering wheel.

4. Turn the switch to the right. A slightdetent in the switch indicates it has beenturned past the off position. After theswitch is turned past the detent, theautolamp automatically turns the lampson and off.

Shut-off delayThe length of time the autolamps stay onafter the ignition is turned to OFF dependson how far the switch is turned to the right.If the switch is turned all the way to the right,the headlights stay on about three minutesafter the ignition is turned to OFF. If theswitch is turned only a little way to the right,the headlights may stay on for less than aminute.

To turn the autolamp system off, turn theswitch all the way to the left until the detentis felt.

Be sure you do not put anything on topof the photo sensor located in the topright side of the instrument panel. Thephoto sensor controls the autolamp; if itis covered, the photo sensor reacts as ifit is dark out and the headlights willilluminate.

Turn signalMove the lever up or down to signal theturning direction. When the turn is com-pleted, the turn signal cancels automati-cally.

Lane change signalTo indicate a lane change, move the leverup or down to the point where the lightbegins to flash, but the lever does not latch.

Passing signalPulling the lever toward you turns the head-light high beam on. Release it and theheadlight high beam goes off.

AIC0584 AIC0560

TURN SIGNAL SWITCH

1-14

Z X

The cornering light provides additional illu-mination toward the turning direction. Thelight on the turning direction side comes onwhen a turn is signaled with the headlightson.

The instrument brightness control operateswhen the light switch is in the or

position, or when the autolamp systemis operating.

Pressing the right side of the switch bright-ens the instrument panel lights; pressing theleft side of the switch dims the instrumentpanel lights.

Push the switch to warn other drivers whenyou must stop or park under emergencyconditions. All turn signal lights flash. Pressthe switch again to turn the hazard warningflashers off.

WARNING● When stalled or stopped on the road-

way under emergency conditions,move the vehicle well off the road.

● Do not use the switch while movingon the highway unless unusual cir-cumstances force you to drive so

AIC0102 AIC0011 AIC0574

CORNERING LIGHT INSTRUMENT BRIGHTNESSCONTROL

HAZARD WARNING FLASHERSWITCH

1-15

Z X

slowly that your vehicle might be-come a hazard to other traffic.

● Turn signals do not work when thehazard warning flasher lights are on.

The flashers can be actuated with the igni-tion switch either OFF or ON.

Some state laws may prohibit the use ofthe hazard warning flasher switch whiledriving.

The cigarette lighter element is an acces-sory. A genuine NISSAN Cigarette Lighteror equivalent can be purchased from yourlocal NISSAN dealer.

The cigarette lighter operates when theignition switch is in the ACC or ON position.

Push the lighter in all the way. When thelighter is heated, it springs out.

Return the lighter to its original position afteruse.

CAUTIONThe cigarette lighter socket is a powersource for the cigarette lighter elementonly. The use of the cigarette lightersocket as a power source for any otheraccessory is not recommended.

WARNINGThe cigarette lighter should not beused while driving in order that fullattention may be given to the drivingoperation.

AIC0579

CIGARETTE LIGHTER(accessory) AND ASHTRAY

1-16

Z X

The rear power point is located on thedriver’s side trim panel of the second rowseats. Open the cover to gain access to thepower point.

Use the power point to plug in electricalequipment such as a cellular telephone, CBradio, etc. Follow the installation instruc-tions included with your electrical equip-ment.

When not in use, always close the powerpoint cover.

CAUTIONWhen using the power point:

● Maximum load of any electricalequipment should not exceed 10amps.

● Be sure to turn off any electricalequipment when not in use. Leavingelectrical equipment on for extendedperiods can discharge your battery.

The slide-out coin tray is located in theinstrument panel below the radio controls.

Do not place valuable items in the cointray.

AIC0581 AIC0575

REAR POWER POINT COIN TRAY

1-17

Z X

The audio cassette and compact disc stor-age compartment is located in the instru-ment panel below the ashtray and lighter.To open the storage compartment, pull outon the handle.

To use the cup holder, pull the cover awayfrom the side of the front passenger seat.Pull the cup holder out of the cover.

To store the cup holder, push it back into thecover and lift the cover to its original positionagainst the side of the seat.

WARNINGThe driver should not pull out the cupholder or remove or insert cups into thecup holder while driving in order that

AHA0014

APD0087

COMPACT DISC AND AUDIOCASSETTE STORAGECOMPARTMENT

CUP HOLDER

1-18

Z X

full attention may be given to thedriving operation.

CAUTION● Avoid abrupt starting and braking

when the cup holder is being used toprevent spilling the drink. If the liq-uid is hot, it can scald you or yourpassenger.

● Use only soft cups in the cup holder.Hard objects can injure you in anaccident.

Second row cup holder(if so equipped)Vehicles equipped with Captain’s chairs inthe second row have a cup holder attachedto the side of the left seat.

Simply pull the cup holder out from the seatto use.

WARNING● Make sure that all passengers have

their hands, etc. inside the vehiclebefore closing the windows. Use thewindow lock switch to prevent unex-pected use of the power windows.

● Do not leave children unattended in-side the vehicle. They could un-knowingly activate switches or con-trols and become trapped in awindow. Unattended children couldbecome involved in serious acci-dents.APD0821

POWER WINDOW

1-19

Z X

The main switch (on the driver side) opensor closes the driver’s or the passenger’swindow.

To open the window, press the switch down.To close the window, lift the switch up.

The power windows operate when the igni-tion key is in the ON position, or for 15minutes after the ignition key is turned to theOFF position. If the driver’s or passenger’sdoor is opened during this 15 minute period,delayed power to the windows is cancelled.

AUTOMATIC POWER WINDOWSWITCHTo fully open the driver side window, pressdown firmly on the switch and release it; youdo not need to hold the switch down. Thewindow automatically opens all the way.

The automatic feature can be interruptedbefore the window is fully open by brieflylifting up on the switch as the window movesdown.

Locking passenger’s windowWhen the power window lock-out button ispushed in, the passenger side window can-not be opened or closed. Push the powerwindow lock-out button again to cancel thisfeature.

AIC0586 AIC0585

1-20

Z X

The passenger side switch opens or closesthe passenger window only. To open thewindow, press the switch down. To closethe window, lift the switch up.

The sunroof operates when the ignition keyis in the ON position, or for 15 minutes afterthe ignition key is turned to the OFF posi-tion. If the driver’s or passenger’s door isopened during this 15 minute period, de-layed power to the sunroof is cancelled.

Sliding the sunroof

To open the roof, push and hold the OPENside of the switch.

To close the roof, push and hold the CLOSEside.

Tilting the sunroofTo tilt up, first close the sunroof, then push theUP side of the tilt switch. To close the sunroof,push the DOWN side of the tilt switch.

Sun shadeOpen and close the sun shade by sliding itforward or backward. The shade openswhen the sunroof opens, but it must beclosed manually.

WARNING● In an accident you could be thrown

from the vehicle through an opensunroof. Always use seat belts andchild restraints.

● Do not allow anyone to stand up orextend any portion of their body outof the opening while the vehicle is inmotion or while the sunroof is clos-ing.

AIC0587 AIC0018

SUNROOF (if so equipped)

1-21

Z X

CAUTION● Remove water drops, snow, ice or

sand from the sunroof beforeopening.

● Do not place any heavy object on thesunroof or surrounding area.

To open the manual rear windows, pull therear portion of the latch toward you until itreleases. To lock the window in the openposition, push the latch rearward until youhear it latch. To close the windows, pull thelatch toward you and push the rear portionof the latch toward the rear of the vehicleuntil you feel it latch.

Use the vent buttons on the power sunroofcontrols to open and close the power rearwindows. To open one of the rear powerwindows, press the indented side of theswitch. To close the window, press theraised side of the switch.

The power rear windows operate when theignition key is in the ON position, or for 15minutes after the ignition key is turned to theOFF position. If the driver’s or passenger’sdoor is opened during this 15 minute period,delayed power to the rear windows is can-celled.

AIC0111 AIC0042

MANUAL REAR WINDOWS POWER REAR WINDOWS(if so equipped)

1-22

Z X

The digital clock displays time when theignition key is in ACC or ON.

If the power supply is disconnected, theclock does not indicate the correct time.Readjust the time.

How to view the clock mode

Push the CLK button to alternate the radiofrequency and the time in the display. In theclock mode, press any radio function toautomatically display the radio frequency for

approximately ten seconds before changingback to the clock mode.

How to set the clock1. Turn the radio on. (Time is displayed

while the radio is off).

2. Push and hold the CLK button; then,press the SEEK button either or

to adjust the hours, and press theTUNE button either or toadjust the minutes.

NOTE: The clock displays 12-hour time withno A.M./P.M. indications.

AIC0580

CLOCK

1-23

Z X

The interior lights operate regardless ofignition key position.

One interior light is located overhead nearthe front seats and one is overhead near therear seat.

The interior lights have three-positionswitches:

● When the switch is in the OFF position,the interior light does not illuminate, re-gardless of door position.

● When the switch is in the center O posi-tion, the light illuminates when a door isopened.

● When the switch is in the ON position,the interior light illuminates, whether anydoor is open or closed.

CAUTIONLeaving the interior light switch in theON position for extended periods oftime will result in a discharged battery.

LUGGAGE COMPARTMENTLIGHTSWhen the back door is opened, the luggagecompartment light and the rear interior lightilluminate.

When the back door is closed, the lights gooff.

The driver’s side, second row seating posi-tion has a personal reading light located inthe overhead trim panel.

To turn the light on, press once on theright-hand side of the light cover.

To turn the light off, press again on theright-hand side of the light cover.

AIC0053 AIC0582

INTERIOR LIGHTS PERSONAL READING LIGHT

1-24

Z X

To turn on the spotlights, press the switchesnext to the lights. To turn them off, press theswitches again.

AIC0049

SPOTLIGHTS

1-25

Z X

2 Pre-driving checks and adjustments

Key .........................................................................2-2Door locks ..............................................................2-2Manual door lock....................................................2-2Child safety sliding door lock .................................2-4Power door lock (if so equipped) ...........................2-5Multi-remote control system (if so equipped).........2-7Battery replacement ...............................................2-8Illuminated entry system ........................................2-9Hood release........................................................2-10Rear door lock......................................................2-11Cargo net (if so equipped) ...................................2-13Luggage rack (if so equipped) .............................2-14Fuel filler lid and cap............................................2-15Seats/floor mats ...................................................2-15Seating arrangements..........................................2-15Floor mat positioning............................................2-17Seven passenger seating ....................................2-17

Three-passenger bench seat in storageposition .................................................................2-17Five passenger seating........................................2-18Five passenger seating with cargo room.............2-18Three-passenger bench seat in fully forwardposition .................................................................2-19Floor mat positioning aid......................................2-20Seat positions.......................................................2-21With second row bench seat................................2-21With second row bucket seats .............................2-24Seats ....................................................................2-26Manual front seat adjustment...............................2-26Power front seat adjustment(if so equipped) ....................................................2-28Head restraints .....................................................2-30Armrests ...............................................................2-30Underseat storage tray.........................................2-31Tabletop seats......................................................2-31

Z X

Flexible seating .................................................2-32Sliding three-passenger seat ...............................2-38Supplemental restraint system (supplementalair bag system).....................................................2-42Supplemental air bag system...............................2-45Warning labels......................................................2-47Supplemental air bag warning light......................2-47Seat belts .............................................................2-49Precautions on seat belt usage ...........................2-49Child safety...........................................................2-503-point type with retractor ....................................2-513-point type seat belt with retractor for secondrow bucket seats ..................................................2-53Three-passenger bench seat ...............................2-572-point type without retractor (center ofthree-passenger bench seat) ...............................2-58Seat belt extenders ..............................................2-60Seat belt maintenance .........................................2-60

Child restraints for infants and small children......2-60Installation at three-passenger bench seatcenter position......................................................2-62Installation at second and third row outboardpositions ...............................................................2-63Child restraint with top tether strap......................2-65Installation on second row bench or bucketseat.......................................................................2-66Installation on three-passenger bench seat insecond row...........................................................2-67Installation on three-passenger bench seat inthird row................................................................2-68Integrated child safety seats (if so equipped)......2-71Tilting steering wheel ...........................................2-78Outside mirror control...........................................2-79Outside mirrors.....................................................2-80Inside mirror .........................................................2-80Vanity mirror .........................................................2-80

Z X

Record the key number on the key numberplate and keep it in a safe place (such asyour wallet), NOT IN THE CAR. A keynumber plate is supplied with your key. Keepthe plate in a safe place. NISSAN does notrecord key numbers so it is very important tokeep track of your key number plate.A key number is necessary only when youhave lost all vehicle keys and do not haveone to duplicate. If you still have a key, thiskey can be duplicated by your NISSANdealer or locksmith shop.Two keys are supplied with your vehicle —one has a plastic head and one is all metal.Both keys perform the same functions.

MANUAL DOOR LOCKTo lock the front doors or sliding door fromthe outside, turn the key toward the front ofthe vehicle. To unlock, turn it toward therear.

APD0142 APD0002

KEY DOOR LOCKS

2-2

Z X

Locking the doors without the keyTo lock the doors from the outside without akey, move the inside lock knob so LOCKEDis visible, then close the door.

When locking the door this way, be certainnot to leave the key inside the vehicle.

Sliding door lockTo lock the sliding door from inside thevehicle, press the door lock rocker switch onthe side marked L. To unlock, press therocker switch on the side marked U.

Only the sliding door locks and unlocks byusing the door lock rocker switch.

APD0840 APD0810

2-3

Z X

WARNING

● Always have the doors locked whiledriving. Along with the use of seatbelts, this provides greater safety inthe event of an accident by helping toprevent persons from being thrownfrom the vehicle. This also helps keepchildren and others from unintention-ally opening the doors, and will helpkeep out intruders.

● Before opening any door, always lookfor and avoid oncoming traffic.

● Do not leave children unattended in-side the vehicle. They could unknow-ingly activate switches or controls. Un-attended children could becomeinvolved in serious accidents.

CAUTION

● Always use the door handle to open orclose the sliding door. Do not attempt toopen or close the door by merely plac-ing your hand on the door edge or doorslide roller, as this may cause injury.

● When opening the sliding door on aslope, ensure that it is fully open andthat it does not close by itself.

CHILD SAFETY SLIDING DOORLOCKChild safety locking helps prevent doorsfrom being opened accidentally, especiallywhen small children are in the vehicle.

When the lever is in the LOCK position,the sliding door can be opened only fromthe outside.

APD0005

2-4

Z X

POWER DOOR LOCK(if so equipped)● Operating the lock-unlock switch locks or

unlocks all doors.

● If the power door lock switch is pressedwhen the sliding door is open, the slidingdoor automatically locks when it isclosed.

WARNING● Before opening any door, always

look for and avoid oncoming traffic.

● Do not leave children unattended in-side the vehicle. They may inadvert-ently activate switches or controls.Unattended children could becomeinvolved in serious accidents.

APD0844 APD0845

2-5

Z X

● Turning a door key to the rear unlocksthat door.

● Turning a door key to the front locks alldoors. This function can be operatedfrom the driver or passenger doors.

● Pushing a front door lock knob in locks alldoors. When locking the doors this way,be certain not to leave the key inside thevehicle. All doors automatically unlockwith the key in the ignition.

Selective unlock● If the vehicle has the multi-remote control

system, turning the door key one time tothe rear of the vehicle unlocks the corre-sponding door. From that position, re-turning the key to Neutral (where the keycan only be removed and inserted) andturning it to the rear again within 5 sec-onds unlocks all doors. This function andlocking all doors can be operated fromthe driver, passenger or sliding door.

APD0841 APD0828

2-6

Z X

It is possible to lock/unlock all doors, turnthe interior lights on or off, and activate thepanic alarm by using the remote controllerfrom outside the vehicle.

Be sure to remove the key from thevehicle before locking the doors andleaving it.

The remote controller can operate at adistance of approximately 49 ft (15 m) fromthe vehicle. (The effective distance dependson the conditions around the vehicle.)

As many as four remote controllers can beused with one vehicle. For more informationconcerning the purchase and use of addi-tional remote controllers, contact your NIS-SAN dealer.

CAUTIONListed below are conditions or occur-rences which will damage the remotecontroller:

● Do not allow the remote controller tobecome wet.

● Do not drop the remote controller.

● Do not strike the remote controllersharply against another object.

● Do not place the remote controllerfor an extended period in an areawhere temperatures exceed 140°F(60°C).

Locking doors

1. Close all of the doors.

2. Push the button on the multi-remotecontroller.

3. All of the doors lock.

4. The parking lights flash twice and thehorn chirps to verify all the doors arelocked.

Unlocking doors

1. Push the button on the multi-remotecontroller. Only the driver side door un-locks.

2. The interior lights come on and stay onfor 30 seconds.

3. Push the button on the multi-remotecontroller again within five seconds. Thepassenger doors and the rear door un-lock.

The interior lights can be turned off withoutwaiting 30 seconds by either turning theignition to ON or locking the doors with themulti-remote controller.

Using the panic alarmIf you are near your vehicle and feel threat-ened, you may activate the panic alarm tocall attention as follows:

1. Push the button on the remote con-troller for at least one full second.

2. The theft warning alarm (horn) soundsand the headlights and tail lights flash for30 seconds.

3. The panic alarm stops when:

● it has run for 30 seconds, or

● the or the button is pressed, or

● the button is released and re-pushed.

MULTI-REMOTE CONTROLSYSTEM (if so equipped)

2-7

Z X

Replace the two batteries as follows:

1. Remove the screw and open the lid.

2. Replace the batteries with new ones.Insert the batteries as illustrated above.

Recommended batteries: Sanyo CR2016or equivalent.

3. Close the lid securely and install thescrew.

4. Press the button, then the button

two or three times to check the multi-remote controller operation.

If the batteries are removed for any rea-son other than replacement, performstep 4 above.

● An improperly disposed battery canhurt the environment. Always confirmlocal regulations for battery disposal.

● The multi-remote controller is water-resistant; however, if it does get wet,immediately wipe completely dry.

● The operational range of the multi-remote controller extends to approxi-mately 49 ft (15 m) from the vehicle.This range may vary with conditions.

FCC Notice:

Changes or modifications not expresslyapproved by the manufacturer for com-pliance could void the user’s authority tooperate the equipment.

This device complies with part 15 of theFCC Rules and RSS-210 of IndustryCanada.

Operation is subject to the following twoconditions: (1) This device may not

APD0623

BATTERY REPLACEMENT

2-8

Z X

cause harmful interference, and (2) thisdevice must accept any interference re-ceived, including interference that maycause undesired operation of the device.

The interior lights, the cargo light, the glovebox light, the stepwell lights near the slidingdoor and on the front doors, and the footwelllights near the driver’s and front passen-ger’s feet illuminate when the front andsliding doors are opened. These lightsgradually dim to off within 30 seconds orturn off immediately when the key is turnedto ON.

Battery saverIf the vehicle doors are not fully closed andthe interior lights remain illuminated, theyeventually turn off automatically to preventthe battery from becoming discharged.Lights that illuminate when the front doorsand/or the sliding door are open turn offafter approximately 30 minutes. Lights thatilluminate when the back door is open turnoff after approximately 60 minutes.

If the personal reading lamp is left on whenthe key is removed from the ignition, it turnsoff automatically in 30 minutes.

ILLUMINATED ENTRYSYSTEM

2-9

Z X

1. Pull the hood lock release handle s1located below the instrument panel; thehood then springs up slightly.

2. Pull up on the lever s2 at the front of thehood and raise the hood.

3. Insert the support rod s3 into the slot onthe underside of the hood.

4. When closing the hood, reset the supportrod to its original position, then slowlyclose the hood and make sure it locksinto place.

WARNING● Make sure the hood is completely

closed and latched before driving.Failure to do so could cause thehood to fly open and result in anaccident.

● If you see steam or smoke comingfrom the engine compartment, toavoid injury do not open the hood.

PD1336M APD0141

HOOD RELEASE

2-10

Z X

Key operationTo unlock the rear door, turn the key coun-terclockwise. To open the rear door, lift upon the opener handle near the license plate.To close, lower and push the rear doordown securely.

To lock the rear door without the key, set thelock lever to the lock position following the‘‘Push to Lock’’ instructions near the latch,then close the rear door securely.

WARNINGDo not drive with the rear door or glassopen. This could allow dangerous ex-haust gases to be drawn into the ve-hicle. See ‘‘Exhaust gas’’ in the ‘‘Start-ing and driving’’ section.

APD0824

REAR DOOR LOCK

2-11

Z X

To lock the rear door with the key, turn thekey clockwise as shown in the illustration.Turning the key fully clockwise unlocks therear window on models equipped with theflip-up rear window. The rear wiper auto-matically lowers when the key is turned fullyclockwise. Do not force the wiper to lowerby hand.

To close the rear window, firmly push on thewindow until it locks in place.

APD0802

2-12

Z X

The cargo net keeps packages in the cargoarea from moving around while your vehicleis driven.

To install the cargo net, attach the fourloops to the four retainers.

To remove the cargo net, detach the fourloops from the cargo net retainers.

WARNING● Properly secure all cargo to help

prevent it from sliding or shifting. Donot place cargo higher than the seat-backs. In a sudden stop or collision,unsecured cargo could cause per-sonal injury.

● Be sure to secure all four loops ontothe retainers. The cargo restrainedby the net must not exceed 50 lbs.(22.7 kg) or the net may not staysecured.

APD0037

CARGO NET(if so equipped)

2-13

Z X

Always distribute the luggage evenly on theluggage rack. Do not load more than 100pounds (45 kg). Be careful that your vehicledoes not exceed the Gross Vehicle WeightRating (GVWR) or its Gross Axle WeightRating (GAWR front and rear). The GVWRand GAWR are located on the Safety Com-pliance Certification Label (located on thedriver’s door pillar). For more informationregarding GVWR and GAWR, refer to‘‘Technical and Consumer Information’’.

The front and rear cross-bars can be ad-justed forward and backward. Place yourluggage between the bars, adjust the bars,

and secure the luggage with rope to thebars. Always check the tightness of theadjusting knobs. There are also adjustableloops on the side bars for the rope attach-ment.

CAUTIONUse care when placing or removingitems from the luggage rack. If youcannot comfortably lift the items ontothe luggage rack from the ground, usea ladder or stool.

APD0158

LUGGAGE RACK(if so equipped)

2-14

Z X

To open the fuel filler lid, grasp the righthand edge of the lid and pull.

The fuel filler cap is a screw-on ratchetingtype. Tighten the cap clockwise until ratch-eting clicks are heard. Ensure the plastictether doesn’t get caught between the gascap and the fuel filler neck.

WARNING● Gasoline is extremely flammable and

highly explosive under certain con-ditions. You could be burned or se-riously injured if it is misused ormishandled. Always stop the engineand do not smoke or allow openflames or sparks near the vehiclewhen refueling.

● Fuel may be under pressure. Turnthe cap one-half turn, and wait forany ‘‘hissing’’ sound to stop to pre-vent fuel from spraying out and pos-sible personal injury. Then removethe cap.

● Use only a genuine NISSAN fuel fillercap as a replacement. It has a built-insafety valve needed for proper op-eration of the fuel system and emis-sion control system. An incorrectcap can result in a serious malfunc-tion and possible injury.

CAUTIONIf fuel is spilled on the vehicle body,flush it away with water to avoid paintdamage.

SEATING ARRANGEMENTSMany different arrangements for passengerseating or cargo hauling are available asyou will see in the following illustrations. Thesecond row seats may be removed and thethird row seat may be moved forward to thesecond row seating position. The secondand third row seats have an optional fold-down table-top feature. This offers a varietyof uses for the vehicle when moving orstopped.

The illustrations shown reflect the differentseating positions available.

Before you begin to arrange the seats inyour vehicle, read all of the cautions andwarnings in this chapter, including thefollowing section on the removable floormats. Also observe any labels that are inthe vehicle.

APD0803

FUEL FILLER LID AND CAP SEATS/FLOOR MATS

2-15

Z X

WARNING● While the vehicle is in motion, pas-

sengers should always be seated ina forward facing direction in a seatwhich is properly secured and ad-justed. Seat belts should always beused. Sitting without a seat belt in aseat that is not properly secured inone of the locations shown in thischapter, or in a place without a seatand seat belt can result in personalinjury in a sudden stop or collision.

● Do not ride in a moving vehicle whenthe seatback is reclined. This can bedangerous. The shoulder belt willnot be against your body. In an acci-dent, you could be thrown into it andreceive neck or other serious inju-ries. You could also slide under thelap belt and receive serious internalinjuries.

● For the most effective protectionwhen the vehicle is in motion, theseat should be upright. Always sitwell back in the seat and adjust theseat belt properly.

● It is extremely dangerous to ride in acargo area inside of a vehicle. In acollision, people riding in these ar-eas are more likely to be seriouslyinjured or killed.

● Do not allow people to ride in anyarea of your vehicle that is notequipped with seats and seat belts.

● Be sure everyone in your vehicle isin a seat and using a seat beltproperly.

● Do not place hard items such ascoffee mugs or drinking glasses onthe tabletop seats when the vehicleis moving. Any item can become aprojectile inside a vehicle involved ina collision. To help prevent personalinjury, never leave loose items onthe fold-down tabletop seats whenthe vehicle is moving.

2-16

Z X

SEVEN PASSENGER SEATING

Removable floor matsWhenever you remove the mats for any reason, the mats must bereinstalled before passengers ride in your vehicle. The floor matsare specifically designed to keep objects out of the seat tracks.

THREE-PASSENGER BENCH SEAT IN STORAGEPOSITION

CAUTIONIt is important to replace the floor mats whenever they areremoved for any reason. The floor mats are intended to helpprevent the possibility that high heeled shoes or similarobjects might become stuck in the seat tracks. Failure toreplace the floor mats might result in personal injury.

Be sure to keep the seat tracks clear of debris by cleaning themperiodically.Review the following illustrations so you will know the proper way toplace the floor mats with the various seating arrangements availablein your vehicle.

APD0847 APD0848

FLOOR MAT POSITIONING

2-17

Z X

FIVE PASSENGER SEATING FIVE PASSENGER SEATING WITH CARGO ROOMThe step mat is not used in this seating configuration.

APD0849 APD0850

2-18

Z X

THREE-PASSENGER BENCHSEAT IN FULLYFORWARD POSITIONThe step mat is not used in this seatingconfiguration.

APD00851

2-19

Z X

FLOOR MAT POSITIONING AID

Positioning pins are attached to three of thefloor mats. The cargo mat and front mats donot have pins. However, the front floor matseach have a grommet which is placed over

the floor mat positioning brackets located atthe base of the front seats.

Push the positioning pins into the seattracks to ensure correct installation, thenstraighten the mats as necessary.

The step mat has holes in addition to pins.When the mats are arranged properly, thepositioning pins of the two mats on eitherside of the step mat should fit through theholes in the step mat and into the seat track.

WARNING● No occupant should ride in a vehicle

seat unless it is in a normal ridingarrangement and the seat belts areproperly used.


● Properly secure all cargo to helpprevent it from sliding or shifting. Donot place cargo higher than the seat-backs. In a sudden stop or collision,unsecured cargo could cause per-sonal injury.

● Do not allow people to ride in anyarea of the vehicle that is notequipped with seats and seat belts.

● Be sure everyone in your vehicle isin a seat and is using a seat beltproperly.

● Failure to follow proper seating in-structions in this section could re-sult in serious personal injury in anaccident or during a sudden stop.

APD0083

2-20

Z X

WITH SECOND ROW BENCHSEATThe most common seating arrangement forseven passengers is with the three-passenger bench seat in seating position#1. This provides more leg room for thepassengers sitting in the third row.

When more cargo area room is necessary,the three-passenger sliding bench seat canbe moved to seating position #2. This seat-ing arrangement provides less leg room forthird row passengers, but more cargo arearoom.

The fold-down tabletop seats in the secondand third rows provide a surface for eatingor playing games on long trips.

APD0096 APD0097 APD0042

SEAT POSITIONS

2-21

Z X

If a considerable amount of cargo arearoom is needed, the seat cushion of thethree-passenger sliding bench seat can beflipped up and the seat can be moved up tostorage position #2, just behind the secondrow seat.

When maximum cargo area is needed andthere are no rear seat passengers, thesecond row seat can be removed and thethree-passenger sliding bench seat can bemoved up to storage position #1, just behindthe front seats.

The second row bench seat can be foldeddown to serve as a tabletop for passengerssitting in the three-passenger bench seat.

APD0043 APD0049 APD0044

2-22

Z X

The second and third row bench seats canbe folded down to tabletops.

To increase cargo area space, the secondrow bench seat can be removed and thethree-passenger sliding seat can be movedup to the second row position.

The third seat can be folded down into atabletop.

APD0045 APD0046 APD0047

2-23

Z X

With the third seat folded down and thesecond seat removed, cargo can be placedin between the front seats and the third rowseat. People should not be allowed toride in areas meant for cargo. Passen-gers should always be properly re-strained in seat belts.

The second row seat can be folded downand the third row seat can be moved justbehind it in a storage position.

WITH SECOND ROW BUCKETSEATSThe normal seating arrangement for sevenpassengers is with the three-passengerbench seat in seating position #1. Thisprovides more leg room for the passengerssitting in the third row.

APD0048 APD0050 APD0128

2-24

Z X

When one passenger in the three-passenger bench seat would like more legroom, one of the second row bucket seatscan be removed.

When more cargo area room is necessary,the three-passenger sliding bench seat canbe moved to seating position #2. This seat-ing arrangement provides less leg room forthird row passengers, but more cargo arearoom.

If passengers in the three-passenger benchseat would like more leg room, both secondrow bucket seats can be removed. Thefloor area should never be used by pas-sengers. Passengers should always beproperly restrained by seat belts.

APD0052 APD0127 APD0053

2-25

Z X

MANUAL FRONT SEATADJUSTMENT

WARNING● Do not adjust the driver’s seat while

driving. The seat may move sud-denly and could cause loss of con-trol of the vehicle.

● After adjustment, gently rock in theseat to make sure it is securelylocked.

Forward and backwardRotate the lever up while you slide the seatforward or backward to the desired position.Release the lever to lock the seat in posi-tion.

RecliningTo recline the seatback, pull the lever upand lean back. To bring the seatback for-ward again, pull the lever and move yourbody forward. The seatback moves forward.Release the lever to lock the seatback inposition.

APD0119

SEATS

2-26

Z X

WARNINGDo not ride in a moving vehicle whenthe seatback is reclined. This can bedangerous. The shoulder belt will notbe against your body. In an accidentyou could be thrown into it and receiveneck or other serious injuries. Youcould also slide under the lap belt andreceive serious internal injuries.

For most effective protection when thevehicle is in motion, the seat should beupright. Always sit well back in the seatand adjust the seat belt properly. See‘‘Precautions on Seat Belt Usage’’ laterin this chapter.

APD0654

2-27

Z X

POWER FRONT SEATADJUSTMENT (if so equipped)

WARNINGDo not adjust the driver’s seat while driv-ing. The seat may move suddenly andcould cause loss of control of the vehicle.

● Do not leave children unattended in-side the vehicle. They could unknow-ingly activate switches or controls. Un-attended children could becomeinvolved in serious accidents.

Operating tips● The motor has an auto-reset overload

protection circuit. If the motor stops dur-ing operation, wait 30 seconds, then re-activate the switch.

● Do not operate the power support seatfor a long period of time when the engineis off. This discharges the battery.

Forward and backward adjustmentTo move the seat forward, push the raisedside of the power slide switch. To move theseat backward, push the indented side ofthe switch. Release the switch to stop themovement of the seat.

Reclining

To recline the seat, push the indented sideof the power recliner switch. To return to amore upright position, push the raised sideof the switch. Release the switch to stop themovement of the seatback.

APD0804

2-28

Z X

Seat height adjustmentTo raise the height of the seat, push theraised side of the power seat height switchand release it when the desired position hasbeen reached. To lower the height of theseat, push the indented side of the switchand release it when the desired position hasbeen reached.

Lumbar supportTo inflate the lumbar support, push theraised side of the power lumbar switch andrelease it when the desired position hasbeen reached. To deflate the lumbar sup-port, push the indented side of the switch.

The power lumbar pump motor continues tooperate after the lumbar support is fullyinflated. Release the switch when the lum-bar stops inflating.

APD0555 APD0805 APD0806

2-29

Z X

HEAD RESTRAINTSAdjust the top of the head restraints levelwith the top of your ears.

To raise the head restraint, pull it up. Tolower, push in the release button and pushthe head restraint down.

WARNINGHead restraints should be adjustedproperly as they may provide signifi-cant protection against injury in an ac-cident. Do not remove them. Check theadjustment after someone else usesthe seat.

Some seat arrangements may require re-moval of the head restraints when the seatis in a storage position and not to be used bypassengers.

ARMRESTS

To use the armrests on any seat, pull themdown to the resting position.

PD1176M APD0022

2-30

Z X

UNDERSEAT STORAGE TRAYSome front passenger seats have an under-seat storage tray.

TABLETOP SEATS

The second and third row seats convert intotabletops with built-in cupholders. To usethe tabletop seats, lift up on the seatbackrelease lever and fold the seatback forward.

WARNING● Never place hard items such as cof-

fee mugs or drinking glasses on thetabletop seats when the vehicle ismoving. Any item can become a pro-jectile inside a vehicle involved in acollision. To help prevent personalinjury, never leave loose items onthe folded-down tabletop seats whenthe vehicle is moving.

● Do not use the tabletop and cupholder feature while the vehicle is inmotion unless you are properlyseated with your seat belt on.

APD0811

APD0129

2-31

Z X

Removing and installing the secondrow bench seat

WARNING● Do not remove or install seats while

the vehicle is moving.

● After adjustment, gently rock in theseat to make sure it is securely locked.

● Do not ride in a moving vehicle whenthe seatback is reclined. This can bedangerous. The shoulder belt willnot be against your body. In an acci-dent you could be thrown into it and

receive neck or other serious inju-ries. You could also slide under thelap belt and receive serious internalinjuries.

● For most effective protection whenthe vehicle is in motion, the seatshould be upright. Always sit wellback in the seat and adjust the seatbelt properly. See ‘‘Precautions onSeat Belt Usage’’ later in this chapter.

● When adjusting or moving any of theseats in your vehicle, do not use anyof the seat belt buckles, tongues, or

webbing to carry or move the seats.Lifting the seats by any of the seatbelts could damage them. Damagedseat belts should be replaced at yourNISSAN dealer. Failure to fol-lowthese instructions could in-crease the chance and/or severity ofinjury in an accident.

CAUTION● The seats are heavy. Two people

should remove or install them.

APD0120

FLEXIBLE SEATING

2-32

Z X

● Do not sit in seats that have beenremoved from the vehicle. They maytip over and you could be injured.

1. Lift up the recliner lever.2. Fold the seatback fully forward.

3. Detach the single window tongue fromthe auxiliary buckle mounted to the sideof the seat and store the tongue out ofthe way. (For detailed information, see‘‘Two buckle seat belt system for thesecond row bench seat’’ later in thissection.)

4. Unlock the seat legs at the two front floorlatch levers.

5. Lift the front of the seat.6. Slide it rearward off the rear anchor

positions.

Installing the second row benchseat

Clean the area around the seat leg flooranchors before installing the seat.

1. With the seatback fully folded, place theseat behind the floor anchors and catchthe seat leg hooks into each floor anchor.

2. Push down on the front of the seat cush-ion to secure the two front floor latches.

3. Lift up the recliner lever and raise theseatback.

4. Rock the seat back and forth to be sure

all four seat legs are securely latched.

5. Insert the single window tongue into theauxiliary buckle mounted to the side ofthe seat.

APD0121

2-33

Z X

Removing second row bucket seats

WARNING● Do not remove or install seats while

the vehicle is moving.

● After adjustment, gently rock in theseat to make sure it is securelylocked.



● For most effective protection whenthe vehicle is in motion, the seatshould be upright. Always sit wellback in the seat and adjust the seatbelt properly. See ‘‘Precautions onSeat Belt Usage’’ later in thischapter.

● When adjusting or moving any of theseats in your vehicle, do not use anyof the seat belt buckles, tongues, orwebbing to carry or move the seats.Lifting the seats by any of the seatbelts could damage them. Damagedseat belts should be replaced at yourNISSAN dealer. Failure to followthese instructions could increasethe chance and/or severity of injuryin an accident.

CAUTION● The seats are heavy. Two people

should remove or install them.

● Do not sit in seats that have beenremoved from the vehicle. They maytip over and you could be injured.

1. Lift the recliner lever.

2. Fold the seatback fully forward.

APD0072

2-34

Z X

3. Unlock the seat legs at the two front floorlatch levers.

4. Lift the front of the seat and slide itrearward off the rear anchor positions.

APD0124

2-35

Z X

Installing the bucket seats

Clean the area around the seat floor attach-ment.

1. With the seatback fully folded, place theseat behind the floor anchors and slideseat leg hooks so they catch into eachfloor anchor.

2. Push down on the front of the seat tosecure the two front floor latches.

3. Lift the recliner lever and raise the seat-back.

4. Rock the seat back and forth to be sure itis securely latched.

5. Lift up on seatback recliner lever to ad-just the seatback to the upright position.

The second row bucket seats are notinterchangeable. If you are having diffi-culty installing the seats, you may havethem in the wrong location.

APD0125

2-36

Z X

Second row passenger side bucketseatThe bucket seat near the sliding door canbe moved forward to allow easier entry andexit for third seat passengers. There arealso levers behind the bucket seat whichallow third seat passengers to move thebucket seat forward without help from an-other passenger.

APD0140APD0161

2-37

Z X

SLIDING THREE-PASSENGERSEAT

RecliningTo recline the three-passenger seat, lift upon the lever and lean back until you reachthe desired angle. To bring the seatbackforward, pull the lever up and lean yourbody forward.

Some three-passenger seats do not havethe recline feature.

WARNING● Do not recline the seatback while the

vehicle is moving.

● Do not ride in a moving vehicle whenthe seatback is reclined. This can bedangerous. The shoulder belt willnot be against your body. In an acci-dent you could be thrown into it andreceive neck or other serious inju-ries. You could also slide under thelap belt and receive serious internalinjuries.

● For most effective protection whenthe vehicle is in motion, the seatshould be upright. Always sit wellback in the seat and adjust the seatbelt properly. See ‘‘Precautions onSeat Belt Usage’’ later in thischapter.

● After adjustment, gently rock in theseat to be sure both sides are se-curely locked.

APD0852

2-38

Z X

Sliding the three-passenger seatBefore sliding the seat, fasten the centerbelt tongue to the center buckle and removethe appropriate floor mats.

1. Lift the seat cushion release lever.

2. Lift the seat cushion up into the lockedposition.

3. Lift the slide release lever and grasp thebar under the seat in the center.

4. Slide the seat until locked at a passengerseating position or a storage position.After the seat starts moving, release theslide lever. The seat latches at the nextlatching position. Continue to lift andrelease the slide lever until the desiredposition is obtained.

To lower the cushion, the seat must be

APD0853

APD0162

2-39

Z X

locked at a passenger seating position. Liftthe seat cushion release lever and lower thecushion until locked.

The seat cushion cannot be lowered in astorage position. This prevents a pas-senger from using a seat or seat belt thatis out of a seating position.

The seating system allows great flexibility.Proper usage is important to your safety.

WARNING

● Do not slide the seat while the ve-hicle is moving.

● After adjustment, gently rock in theseat to be sure it is securely locked.

● After sliding the seat, check that bothsides of the seat are locked securelyby attempting to move each side ofthe seat forward and backward. Thismust be done before the vehicle isput into motion in order to prevent

unintended movement of the seat andpassenger injuries.

● Do not attempt to use the seatsplaced into a storage position forpassengers because in this positionthe seat belts will not protect theoccupants. Be sure to use the properseat belts for each seat location.Improper seat belt usage will in-crease the risk of severe injury in anaccident.

● When the vehicle is being used tocarry cargo, properly secure all cargoto help prevent it from sliding or shift-ing. Do not place cargo higher thanthe seatbacks. In a sudden stop orcollision, unsecured cargo couldcause personal injury.

● Be careful not to damage the seatbelt. Never allow anyone to ride in thecargo area or on a seat that is in astorage position. It is not designedfor passengers. They could be in-jured in sudden braking or a collision.

● To prevent luggage or packagesfrom sliding forward during braking,

APD0126

2-40

Z X

do not stack anything in the cargoarea higher than the seatbacks.



● Be sure everyone in your vehicle isin a seat and using a seat beltproperly.

● Be sure to replace and repositionfloor mats as discussed in ‘‘Floormat positioning’’ in this section.

● The three-passenger sliding benchseat is not intended to be removedfrom the vehicle by consumers.However, if it must be removed, havea qualified person remove it. Thatperson should refer to the instruc-tions in the Service Manual. Whenseat is reinstalled, the attachingbolts must be tightened to the appro-priate torque specifications. Failure

to follow these instructions couldincrease the chance and/or severityof injury in an accident.

Cleaning the seat tracksThe seat tracks for the three-passengersliding bench seat should be cleaned peri-odically with a high-powered vacuumcleaner. If the seat tracks become dirty itmay reduce the ability to slide the seat. Awet cleansing agent may be used if neces-sary, but the seat tracks must be thoroughlydried.

Use a cloth wrapped around a screwdriver(or similar object) to clean the seat tracks.Do not use your fingers to clean debris fromthe tracks.

Do not apply any type of lubricant to theseat tracks.

CAUTIONNever insert fingers into the seat trackrails. The rails may be sharp and couldcause injury.

2-41

Z X

This Supplemental Restraint System de-scription contains important information con-cerning the special driver and passengersupplemental air bag. The Supplemental Re-straint System Air Bag can help reduce im-pact force to the driver and to the frontpassenger in certain frontal collisions. Thesupplemental air bags are designed tosupplement the crash protection providedby the seat belts and are not a substitute forthe seat belts. The supplemental seat beltsshould always be correctly worn and thedriver and front passenger seated a suitabledistance from the steering wheel and instru-ment panel. (See ‘‘Seat belts’’ for instructionsand precautions on seat belt usage.)

The supplemental air bags operate onlywhen the ignition switch is in the ON orSTART position.

WARNING● The supplemental air bag ordinarily

will not inflate in the event of a sideimpact, rear impact, roll over, or lowerseverity frontal collision. Always wearyour seat belts to help reduce the riskor severity of injury in various kinds ofaccidents.

● The seat belts and the supplementalair bag are most effective when you aresitting back and upright in the seat.Supplemental air bags inflate withgreat force. If you are unrestrained,leaning forward, sitting sideway, you

are at greater risk of injury or deathin a crash and may also receiveserious or fatal injuries from thesupplemental air bag if you are upagainst it when it inflates.

● Always sit back against the seatbackand as far away as practical from thesteering wheel or instrument panel.Always use the seatbelts.

● Keep hands on the outside of thesteering wheel. Placing them insidethe steering wheel rim could increasethe risk that they are injured when thesupplemental air bag inflates.

APD0717

SUPPLEMENTAL RESTRAINTSYSTEM (supplemental air bagsystem)

2-42

Z X

APD0656 APD0650

APD0651

2-43

Z X

WARNING● Never let children ride unrestrained.

Do not attempt to hold them in yourlap or arms. Some examples of dan-gerous riding positions are shown inthe previous illustrations.

● Children may be severly injured orkilled when the supplemental air baginflates if they are not properlyrestrained.

● Also, never install a rear-facing childrestraint in the front seat. An inflat-ing supplemental air bag could seri-ously injure or kill your child. See‘‘Child restraints for infants andsmall children’’ for details.

APD0653 APD0648

APD0652 APD0660

2-44

Z X

The driver supplemental air bag is located inthe center of the steering wheel; the frontpassenger supplemental air bag is mountedin the dashboard above the glove box. Thesupplemental air bag system is designed toinflate in higher severity frontal collisions,although it may inflate if the forces in an-other type of collision are similar to those ofa higher severity frontal impact. It may notinflate in certain frontal collisions. Vehicledamage (or lack of it) is not always anindication of proper supplemental air bagoperation.

When the supplemental air bag inflates, a

fairly loud noise may be heard, followed bythe release of smoke. This smoke is notharmful and does not indicate a fire, butcare should be taken not to unintentionallyinhale it, as it may cause irritation andchoking. Those with a history of breathingtrouble should get fresh air promptly.

The supplemental air bags, along with theuse of seat belts, help to cushion the impactforce on the face and chest of the occupant.They can help save lives and reduce seri-ous injuries. However, an inflating supple-mental air bag may cause facial abrasionsor other injuries. Supplemental air bags do

not provide restraint to the lower body.

Seat belts should be correctly worn and thedriver and passenger seated upright as faras practical away from the steering wheel ordashboard. Since the supplemental air baginflates quickly in order to help protect theoccupant, the force of the supplemental airbag inflating can increase the risk of injury ifthe occupant is too close to or is against thesupplemental air bag module during infla-tion.

The supplemental air bag deflates quicklyafter a collision. The supplemental airbags operate only when the ignitionswitch is in the ON or START position.

WARNING● Do not place any objects on the

steering wheel pad or the instrumentpanel. Also, do not place any objectsbetween any occupant and the steer-ing wheel or instrument panel. Suchobjects may become dangerous pro-jectiles and cause injury if thesupplemental air bag inflates.

APD0846

SUPPLEMENTAL AIR BAGSYSTEM

2-45

Z X

● Right after inflation, several supple-mental air bag system componentswill be hot. Do not touch them; youmay severely burn yourself.

● No unauthorized changes should bemade to any components or wiringof the supplemental air bag system.This is to prevent accidental inflationof the supplemental air bag or dam-age to the supplemental air bagsystem.

● Do not make unauthorized changesto your vehicles electrical system,suspension system or front endstructure. This could affect properoperation of the supplemental airbag system.

● Tampering with the supplemental airbag system may result in seriouspersonal injury. Tampering includeschanges to the steering wheel andthe instrument panel assembly byplacing material over the steeringwheel pad and above the instrumentpanel, or by installing additional trimmaterial around the supplemental airbag system.

● Work around and on the supplemen-tal air bag system should be done byan authorized NISSAN dealer. Instal-lation of electrical equipment shouldalso be done by an authorized NIS-SAN dealer. The yellow SRS wiringshould not be modified or discon-nected. Unauthorized electrical testequipment and probing devicesshould not be used on the supple-mental air bag system.

● The SRS wiring harnesses are cov-ered with yellow insulation eitherjust before the harness connectorsor over the complete harness foreasy identification.

When selling your vehicle, we request thatyou inform the buyer about the supplemen-tal air bag system and guide the buyer to theappropriate sections in this Owner’sManual.

2-46

Z X

Warning labels about the supplemental airbag system are placed in the vehicle.

The supplemental air bag warning light,displaying AIR BAG in the instrument panel,monitors the circuits of the supplemental airbag. The circuits monitored by the supple-mental air bag light are the diagnosis sensorunit, supplemental air bag modules and allrelated wiring.

When the ignition key is in the ON or STARTposition, the supplemental air bag warninglight illuminates for about 7 seconds andthen turns off. This means the system isoperational.

APD1017 APD0554

WARNING LABELS SUPPLEMENTAL AIR BAGWARNING LIGHT

2-47

Z X

If any of the following conditions occur, thesupplemental air bag needs servicing andshould be taken to your nearest authorizedNISSAN dealer:

1. The supplemental air bag light does notcome on and remain on for 7 secondsand then go off as described above.

2. The supplemental air bag light flashesintermittently or remains on.

3. The supplemental air bag light does notcome on at all.

Under these conditions, the SupplementalRestraint System Air Bag may not operateproperly. It must be checked and repaired.Take your vehicle to the nearest authorizedNISSAN dealer.

WARNINGIf the supplemental air bag warninglight is on, it could mean that the airbag will not operate in an accident.

Repair and replacement procedureThe supplemental air bag system is de-signed to inflate on a one-time-only basis.As a reminder, unless it is damaged, the

supplemental air bag light remains illumi-nated after inflation has occurred. Repairand replacement of the supplemental airbag system should be done only by anauthorized NISSAN dealer.

To ensure long-term functioning, thesystem must be inspected 10 years afterthe date of manufacture as noted on thecertification label located on the driverside front pillar.

When maintenance work is required on thevehicle, the supplemental air bag systemand related parts should be pointed out tothe person conducting the maintenance.The ignition key should always be in theLOCK position when working under thehood or inside the vehicle.

WARNING● Once the supplemental air bag in-

flates, the supplemental air bagmodule will not function again andshould be replaced by an authorizedNISSAN dealer. The supplemental airbag module cannot be repaired.

● The supplemental air bag systemshould be inspected by an autho-rized NISSAN dealer if there is anydamage to the front end portion ofthe vehicle.

● If you need to dispose of a supple-mental air bag or scrap the vehicle,contact an authorized NISSANdealer. Correct supplemental air bagdisposal procedures are set forth inthe appropriate NISSAN ServiceManual. Incorrect disposal proce-dures could cause personal injury.

2-48

Z X

PRECAUTIONS ON SEAT BELTUSAGEYour chances of being injured or killed in anaccident and/or the severity of injury may begreatly reduced if you are wearing your seatbelt and it is properly adjusted. NISSANstrongly encourages you and all of yourpassengers to buckle up every time youdrive, even if your seating position includesa supplemental air bag.

Some states and all Canadian provincesor territories require that seat belts beworn at all times when a vehicle is beingdriven.

WARNING● Every person who drives or rides in

this vehicle should wear a seat beltat all times. Children should be prop-erly restrained and, if appropriate, ina child restraint.

● The belt should be adjusted to a snugfit. Failure to do so may reduce theeffectiveness of the entire restraintsystem and increase the chance orseverity of injury in an accident. Seri-ous injury or death can occur if theseat belt is not worn properly.

● Always route the shoulder belt overyour shoulder and across your chest.Never run the belt behind your back,under your arm or across your neck.The belt should be away from yourface and neck, but not falling off yourshoulder.

● Position the lap belt as low and snugas possible AROUND THE HIPS,NOT THE WAIST. A lap belt worn toohigh could increase the risk of inter-nal injuries in an accident.

APD0658 APD0718

SEAT BELTS

2-49

Z X

● Be sure the seat belt tongue is se-curely fastened to the proper buckle.

● Do not wear the belt inside out ortwisted. Doing so may reduce itseffectiveness.

● Do not allow more than one personto use the same seat belt.

● Never carry more people in the ve-hicle than there are seat belts.

● If the seat belt warning light glowscontinuously while the ignition isturned ON with all doors closed andall seat belts fastened, it may indi-cate a malfunction in the system.Have the system checked by yourNISSAN dealer.

● All seat belt assemblies, includingretractors and attaching hardware,should be inspected at your NISSANdealer after any collision. NISSANrecommends that all seat belt as-semblies in use during a collision bereplaced unless the collision wasminor and the belts show no dam-ageand continue to operate prop-erly. Seat belt assemblies not in useduring a collision should also beinspected and replaced if eitherdamage or improper operation isnoted.

CHILD SAFETY

Children need adults to help protectthem.

WARNING

Infants and children need special pro-tection. The vehicle’s seat belts maynot fit them properly. The shoulder beltmay come too close to the face or neck.The lap belt may not fit over their smallhip bones. In an accident an improperlyfitting seat belt could cause serious orfatal injury. Always use appropriatechild restraints.

All U.S. states and provinces of Canadarequire the use of approved child restraintsfor infants and small children. (See ‘‘Childrestraints for infants and small children’’later in this section.)

In addition, there are many types of childrestraints available for larger children whichshould be used for maximum protection.

Infant or small childNISSAN recommends that infants or smallchildren be placed in a child restraint that

APD0533

2-50

Z X

complies with the Federal Motor VehicleSafety Standards or Canadian Motor Ve-hicle Safety Standards. You should choosea child restraint that fits your vehicle andalways follow the manufacturer’s instruc-tions for installation and use.

ChildrenChildren who are too large for child re-straints should be seated and restrained bythe seat belts which are provided.

NISSAN recommends that children sit in arear seat if possible. According to accidentstatistics, children are safer when properlyrestrained in a rear seat than in a front seat.

If the child’s seating position has a shoulderbelt that fits close to the face or neck, theuse of a booster seat (commercially avail-able) may help overcome this. The boosterseat should raise the child so the shoulderbelt is properly positioned across the top,middle portion of the shoulder and the lapbelt is low on the hips. The booster seatshould fit the vehicle seat and have a labelcertifying that it complies with Federal MotorVehicle Safety Standards or Canadian Mo-tor Vehicle Safety Standards. Once thechild has grown enough so the shoulder beltis no longer on or near the face and neck,

use the shoulder belt without the boosterseat.

WARNINGNever let a child stand or kneel on anyseat and do not allow a child in thecargo areas while the vehicle is mov-ing. The child could be seriously in-jured or killed in an accident.

Pregnant womenNISSAN recommends that pregnant womenuse seat belts. Contact your doctor for spe-cific recommendations. The lap belt shouldbe worn snug and positioned as low aspossible around the hips, not the waist.

Injured personsNISSAN recommends injured persons useseat belts, depending on the injury. Checkwith your doctor for specific recommenda-tions.

3-POINT TYPE WITH RETRACTOR


this vehicle should wear a seat beltat all times.

● Do not ride in a moving vehicle whenthe seatback is reclined. This can bedangerous. The shoulder belt willnot be against your body. In an acci-dent you could be thrown into it andreceive neck or other serious inju-ries. You could also slide under the

APD0500

2-51

Z X

lap belt and receive serious internalinjuries.

● For most effective protection whenthe vehicle is in motion, the seatshould be upright. Always sit wellback in the seat and adjust the seatbelt properly.

Fastening the belts1. Adjust the seat.

2. Slowly pull the seat belt out of the retrac-tor and insert the tongue into the buckleuntil it snaps.

The retractor is designed to lock duringa sudden stop or on impact. A slowpulling motion permits the belt to move,and allows you some freedom of move-ment in the seat.

3. Position the lap belt portion low andsnug on the hips as shown.

4. Pull the shoulder belt portion toward theretractor to take up extra slack.

The front seat passenger side seat belt andrear 3-point seat belts have a cinchingmechanism for child seat installation. It isreferred to as the automatic locking mode.

When the automatic locking mode is acti-vated, the seat belt cannot be withdrawnagain until the seat belt tongue is detachedfrom the buckle and fully retracted. Refer to‘‘Child restraints for infants and smallchildren’’ later in this section for more infor-mation.

The automatic locking mode should beused only for child seat installation. Dur-ing normal seat belt use by a passenger,the locking mode should not be acti-vated. If it is activated, it may causeuncomfortable seat belt tension.

Unfastening the beltsTo unfasten the belt, press the button on thebuckle. The seat belt automatically retracts.

PD1024M

2-52

Z X

Shoulder belt height adjustmentThe shoulder belt anchor height should beadjusted to the position best for you. (See‘‘Precautions on seat belt usage’’.) To ad-just, press the release button and move it tothe desired position so the belt passes overthe center of the shoulder. The belt shouldbe away from your face and neck, but notfalling off your shoulder.

WARNINGAfter adjustment, release the buttonand check that it does not move up anddown to make sure the shoulder beltanchor is securely fixed in position.

3-POINT TYPE SEAT BELT WITHRETRACTOR FOR SECONDROW BUCKET SEATS


this vehicle should wear a seat beltat all times.


APD0831 APD0829

2-53

Z X



Fastening the belts1. Adjust the seat.


The retractor is designed to lock duringa sudden stop or on impact. A slowpulling motion permits the belt to move,and allows you some freedom of move-ment in the seat.

3. Position the lap belt portion low on thehips as shown.


Two buckle seat belt system for thesecond row bench seatThere is a two buckle seat belt system forthe seating position of the second rowbench seat next to the sliding door.

WARNING● It is very important that you follow

the instructions in this section be-fore anyone rides in this seating po-sition of the two-passenger benchseat.

● Failure to do so may result in im-proper positioning of seat belt whichcould lead to increased likelihood orseverity of injury in a sudden stop orcollision.

APD0830

2-54

Z X

The two-passenger bench seat in the sec-ond row has a seat belt system made up oftwo buckles and two tongues. There are twobody attaching points (one upper and onelower) that attach each end of the seat beltwebbing.

One of the seat belt tongues has two ‘‘win-dows’’ (or holes) and the other has only one‘‘window’’. The seat belt tongue with onewindow attaches to the buckle mounted tothe side of the seat. The seat belt tonguewith two windows should be positioned

properly and fastened to the bucklemounted in the location in the middle of theseat.

When the two buckle seat belt system is notin use, the webbing can be secured with theseat belt clip. The seat belt clip should notbe used with a child seat or during seat beltusage. The seat belt clip opening shouldface the front of the vehicle.

APD0558 APD0123

2-55

Z X

A twisted belt may prevent the retractorfrom working properly. If the two buckle seatbelt system is twisted, disengage the singlewindow tongue from the buckle on the sideof the seat, remove the twist and reinstallthe tongue into the buckle until you hear asnap and feel the latch engage.

Both tongues must be attached to theirappropriate buckles whenever someoneis riding in that seating position. If thetongue is released to allow a third rowpassenger to enter or exit, the tonguemust be reattached.

When the two-passenger bench seat is re-

moved from the vehicle, you must detachthe single window tongue from the auxiliarybuckle.

If the three-passenger bench seat ismoved up to the second row position,the outside passenger (near the slidingdoor) only needs to use the double win-dow tongue and the standard buckle.Because the third row seat is so muchwider and is closer to the sliding door,the single window tongue and the auxil-iary buckle are not necessary.

CAUTION

Third row passengers must be verycareful when exiting because of theauxiliary seat belt. It is important tostep over the seat belt guide and beltwebbing to avoid tripping.

Unfastening the belts

To unfasten the belt, press the button on thebuckle. The seat belt automatically retracts.

APD0093 APD0089

2-56

Z X

Checking seat belt operation(3-point type with retractor)The second and third row seat belt retrac-tors are designed to lock belt movement:

1) when the belt is pulled quickly from theretractor, and

2) when the vehicle slows down rapidly.

To increase your confidence in the belts,check their operation. Grasp the shoulderbelt and pull quickly forward. The retractorshould lock and restrict further belt move-ment.

If the retractor does not lock during thischeck or if you have any questions aboutbelt operation, see your NISSAN dealer.

THREE-PASSENGER BENCHSEAT

Fastening the seat belts1. Adjust the seat.

WARNING● Do not ride in a moving vehicle when

the seatback is reclined. This can bedangerous. The shoulder belt willnot be against your body. In an acci-dent you could be thrown into it andreceive neck or other serious inju-ries. You could also slide under thelap belt and receive serious internalinjuries.


Third row passengers should be aware thattheir shoulder belt is located slightly behindthe third row seating position. Never try touse the seat belts for the second row pas-sengers which are in front of the three-passenger bench seat.

APD0091

2-57

Z X

WARNINGUse of the second row 3-point seatbelts by third row passengers couldincrease injury in a sudden stop or anaccident.


The retractor is designed to lock duringa sudden stop or on impact. A slowpulling motion permits the belt to move,and allows you some freedom of move-ment in the seat. 3. Position the lap belt portion low on the

hips as shown.


2-POINT TYPE WITHOUTRETRACTOR (Center of three-passenger bench seat)

Fastening the belts1. Insert the tongue into the buckle until it

snaps.

APD0131 APD0094

2-58

Z X

2. To lengthen, hold the tongue at a rightangle to the belt and pull on the belt. Toshorten, pull the free end of the belt awayfrom the tongue.

3. Position the lap belt low on the hips asillustrated.

Unfastening the beltsTo unfasten the belt, press the button on thebuckle.

Selecting correct set of belts

The seat belt tongues must be fastened intothe seat belt buckles as illustrated above.

WARNING

Any rear seat belt tongue will connectto any seat belt buckle; therefore, it isimportant to follow the illustrationabove. Failure to do so could increasethe chance and/or severity of injury inan accident.

APD0095 APD0167 APD0162

2-59

Z X

SEAT BELT EXTENDERS

If, because of body size or driving position,it is not possible to properly fit the front seatlap belts and fasten them, an extender isavailable which is compatible with the in-stalled seat belts. The extender adds ap-proximately 8 inches (200 mm) of lengthand may be used for either lap belt for thedriver or front passenger seating position.See your NISSAN dealer for assistance ifthe extender is required.

WARNING● Only NISSAN belt extenders, made

by the same company which madethe original equipment belts, shouldbe used with NISSAN belts.

● Persons who can use the standardseat belt should not use an extender.Such unnecessary use could resultin serious personal injury in theevent of an accident.

SEAT BELT MAINTENANCE● To clean the seat belt webbings, apply

a mild soap solution or any solution rec-ommended for cleaning upholstery or

carpets. Then brush the webbing, wipe itwith a cloth and allow it to dry in theshade. Do not allow the seat belts toretract until they are completely dry.

● If dirt builds up in the shoulder beltguide of the seat belt anchors, the seatbelts may retract slowly. Wipe the shoul-der belt guide with a clean, dry cloth.

● Periodically check to see that the seatbelt and the metal components suchas buckles, tongues, retractors, flexiblewires and anchors work properly. If looseparts, deterioration, cuts or other dam-age on the webbing is found, the entireseat belt assembly should be replaced.

WARNING● Infants and small children should

always be placed in an appropriatechild restraint system while riding inthe vehicle. Failure to use a childrestraint can result in serious injuryor death.

● Children and infants should never becarried on your lap. It is not possiblefor even the strongest adult to resistthe forces of a severe accident. Thechild could be crushed between theadult and parts of the vehicle. Also,do not put the same seat belt aroundboth your child and yourself.

● NISSAN recommends that the childrestraint be installed in a rear seat.According to accident statistics,children are safer when properly re-strained in a rear seat than in a frontseat.

● An improperly installed child re-straint could lead to serious injury inan accident.

CHILD RESTRAINTS FORINFANTS AND SMALLCHILDREN

2-60

Z X

● In general, child restraint systemsare designed to be installed with alap belt or the lap portion of a three-point type seat belt.

Child restraints specially designed for in-fants and small children are offered byseveral manufacturers. When selecting anychild restraint, keep the following points inmind:

1) Choose only a restraint with a label cer-tifying that it complies with Federal MotorVehicle Safety Standard 213 or Cana-dian Motor Vehicle Safety Standard 213.

2) Check the child restraint in your vehicleto be sure it is compatible with the vehi-cle’s seat and seat belt system. Choosea child restraint that meets the guidelinesof the Society of Automotive Engineersrecommended practice J1819 for childseat installation.

3) If the child restraint is compatible withyour vehicle, place your child in the childrestraint and check the various adjust-ments to be sure the child restraint iscompatible with your child. Always followall recommended procedures.

All U.S. states and some provinces orterritories of Canada require that infantsand small children be restrained in ap-proved child restraints at all times whilethe vehicle is being operated.

WARNING● Never install a rear-facing child re-

straint in the front seat. An inflatingair bag could seriously injure or killyour child. A rear-facing child re-straint must only be used in the rearseat. See ‘‘Installation on front pas-senger seat’’ for details.

● Improper use of a child restraint canresult in increased injuries for boththe infant or child and other occu-pants in the vehicle.

● Follow all of the child restraintmanufacturer’s instructions for in-stallation and use. When purchasinga child restraint, be sure to selectone which will fit your child andvehicle. It may not be possible toproperly install some types of childrestraints in your vehicle.

● If the child restraint is not anchoredproperly, the risk of a child beinginjured in a collision or a suddenstop greatly increases.

● Adjustable seatbacks should be po-sitioned to fit the child restraint, butas upright as possible.

● After attaching the child restraint,test it before you place the child in it.Tilt it from side to side. Try to tug itforward and check to see if the beltholds the restraint in place. If therestraint is not secure, tighten thebelt as necessary, or put the restraintin another seat and test it again.

● For a front facing child restraint, ifthe seat position where it is installedhas a 3-point type lap/shoulder belt,check to make sure the shoulder beltdoes not go in front of the child’sface or neck. If it does, put the shoul-der belt behind the child restraint.

● When your child restraint is not inuse, keep it secured with a seat beltto prevent it from being thrownaround in case of a sudden stop oraccident.

2-61

Z X

CAUTIONRemember that a child restraint left in aclosed vehicle can become very hot.Check the seating surface and bucklesbefore placing your child in the childrestraint.

INSTALLATION AT THREE-PASSENGER BENCH SEATCENTER POSITIONWhen you install a child restraint in a rearcenter seat, follow these steps:

1. Position the child restraint on the seat asillustrated. It can be placed in a forwardfacing or rear facing direction, dependingon the size of the child. Always follow therestraint manufacturer’s instructions.

2. Route the seat belt tongue through thechild restraint and insert it into the buckleuntil you hear and feel the latch engage.

Be sure to follow the child restraint manu-facturer’s instructions for belt routing.

3. Remove all slack in the lap belt for a verythight fit by pulling forcefully on the lapbelt adjustment.

4. Before placing the child in the child re-straint, use force to tilt the child restraintfrom side to side, and tug it forward tomake sure it is securely in place.

5. If it is not secure, try to tighten the beltagain, or put the restraint in another seat.

6. Check to make sure the child restraint isproperly secured prior to each use.

APD0534

2-62

Z X

INSTALLATION AT SECONDAND THIRD ROW OUTBOARDPOSITIONSThe following instructions apply to secondrow bucket seats, the second row benchseat and the outboard positions of the three-passenger bench seat.

WARNINGWhen installing a child restraint in thetwo-passenger bench seat, if it isplaced in the seating position next tothe sliding door, be sure both the aux-iliary buckle and main buckle are prop-erly fastened. Failure to do so couldincrease the chance and/or severity ofinjury in an accident.

WARNING

● The 3-point belt in your vehicle isequipped with a locking mode re-tractor which must be used wheninstalling a child restraint.

● Failure to use the retractor’s lockingmode will result in the child restraintnot being properly secured. The seatcould tip over or otherwise be unse-cured and cause injury to the child ina sudden stop or collision.

PD1331APD0169

2-63

Z X

When you install a child restraint in a rearoutboard seat, follow these steps:

1. Position the child restraint on the seat. Itcan be placed in a forward facing or rearfacing direction, depending on the size ofthe child. Always follow the restraintmanufacturer’s instructions.



3. Pull on the shoulder belt until all of thebelt is fully extended and a click is heard.At this time, the belt retractor is in theautomatic locking mode (child restraintmode). (It reverts back to ‘‘emergencylocking’’ when the belt is fully retracted.)

4. Allow the belt to retract. A clicking soundis heard as the belt retracts. This indi-cates that the retractor is in the automaticlocking mode. Pull up on the shoulderbelt to remove any slack in the belt.

5. Before placing the child in the child re-straint, use force to tilt the child restraintfrom side to side, and tug it forward tomake sure it is securely held in place.

6. Check that the retractor is in the auto-matic locking mode by trying to pull morebelt out of the retractor. If you cannot pullany more belt webbing out of the retrac-tor, the belt is in the automatic lockingmode.

7. Check to make sure the child restraint isproperly secured prior to each use. If thebelt is not locked, repeat steps 3 through6.

After the child restraint is removed and theseat belt is allowed to wind back into theretractor (for the passenger side of thetwo-passenger bench seat the auxilliarybuckle must also be released), the auto-matic locking mode (child restraint mode) iscanceled; the seat belt may be used asnormal and will only lock during a suddenstop or impact.

PD1332

2-64

Z X

A child restraint anchored with a top tetherstrap can be installed on the second rowbench seat, second row bucket seat, orthree-passenger bench seat in the secondor third row. The chart below indicateswhere the tether strap must be attached andthe section containing the instructions fortethering.

Seat type Position Tether to Reference

2-passenger bench orbucket seat

2nd row; 3-passengerbench seat in seatingor storage position

Tongue of 3rd rowlap/shoulder belt di-rectly behind the childseat position

Page 2-62,Tethering tolap/shoulder belttongue

3-passenger benchseat

2nd row; outboardseating position

Tongue of 3rd rowlap/shoulder belt di-rectly behind the childseat position

Page 2-63, Tetheringto lap/shoulder belttongue


2nd row; center seat-ing position

CANNOT BE

TETHERED—


3rd row; outboard orcenter seating posi-tion

Floor anchor directlybehind the child seatposition

Page 2-64, Tetheringto floor

CHILD RESTRAINT WITH TOPTETHER STRAP

2-65

Z X

INSTALLATION ON SECONDROW BENCH OR BUCKET SEATA child restraint with a top tether strap maybe placed on the second row bench orbucket seats. Once the child restraint isproperly secured to the seat (see ‘‘Installa-tion at second and third row outboard posi-tions’’ earlier in this section), follow thedirections below to attach the tether strap tothe third row lap/shoulder belt tongue lo-cated on the same side of the vehicle as thechild restraint.

Tethering to lap/shoulder belttongueTo attach a tether strap to a third rowlap/shoulder belt:

1. Route the tether strap under the headrestraint and between the head restraintsupports.

2. Hook the tether strap into the large holeon the tongue of the third rowlap/shoulder belt (located near the upperand lower rear corners of the vehicle).

3. Adjust the tether strap until the hook isabout one foot behind the seatback.

4. Pull on the third row shoulder belt until allof the belt is fully extended and a click isheard. At this time, the belt retractor is inthe automatic locking mode (child re-straint mode). (The lap/shoulder belt re-verts back to emergency locking modewhen it is disconnected from the tetherstrap and fully retracted.)

5. Allow the belt to retract. A clicking soundis heard as the belt retracts. This indi-cates that the retractor is in the automaticlocking mode. Tighten the tether strapand remove any slack.

APD0832 APD0833 APD0834

2-66

Z X



8. Check to make sure the child restraint isproperly secured prior to each use. If thebelt is not locked, repeat steps 4 through7.

WARNINGA third seat occupant should never sitat a seating location where the lap/shoulder belt is being used to attachthe child seat. Occupants should sit atlocations where seat belts can be used.Remember always wear your seat belt.

INSTALLATION ON THREE-PASSENGER BENCH SEAT INSECOND ROWA child restraint with a top tether strap maybe placed at the outboard positions on thethree-passenger bench seat when thebench seat is in the second row location.Once the child restraint is properly securedto the seat (see ‘‘Installation at second andthird row outboard positions’’ earlier in thissection), follow the directions below to at-tach the tether strap to the third rowlap/shoulder belt tongue located on thesame side of the vehicle as the child re-straint.

Tethering to lap/shoulder belt tongue

To attach a tether strap to a third rowlap/shoulder belt:

1. Route the tether strap under the headrestraint and between the head restraintsupports.

2. Hook the tether strap into the large holeon the tongue of the third rowlap/shoulder belt (located near the upperand lower rear corners of the vehicle).

3. Adjust the tether strap until the hook isabout one foot behind the seatback.

APD0839 APD0835

2-67

Z X

4. Pull on the third row shoulder belt until allof the belt is fully extended and a click isheard. At this time, the belt retractor is inthe automatic locking mode (child re-straint mode). (The lap/shoulder belt re-verts back to emergency locking modewhen it is disconnected from the tetherstrap and fully retracted.)

5. Allow the belt to retract. A clicking soundis heard as the belt retracts. This indi-cates that the retractor is in the automaticlocking mode. Tighten the tether strap toremove any slack.



8. Check to make sure the child restraint isproperly secured prior to each use. If thebelt is not locking, repeat steps 4 through7.

INSTALLATION ON THREE-PASSENGER BENCH SEAT INTHIRD ROW

A child restraint with a top tether strap maybe placed on the three-passenger benchseat when the bench seat is in the third rowlocation. Once the child restraint is properlysecured to the seat (see ‘‘Installation atsecond and third row outboard positions’’ or‘‘Installation at three-passenger bench seatcenter position’’ earlier in this section), fol-low the directions below to attach the tetherstrap to one of the anchor points.

Tethering to floorWhen installing a child restraint on thethree-passenger bench seat in the third rowposition, first install the floor anchor bracket(found in the tool kit) to the provided anchorpoint. To gain access to an anchor point, cutalong the U-shaped anchor point indicatorson the floor carpeting of the luggage area.Installing the anchor bracket requires re-moving the bolt already installed at theanchor point and using a metric bolt of thedimensions listed below:

Bolt diameter: 8.0 mmBolt length: more than 1.18 in (30 mm)Thread pitch: 1.25 mm

WARNING● Bolts should be installed at all times

to prevent the possibility of exhaustfumes entering the passenger com-partment through the holes.

● Child restraint anchor points are de-signed to withstand only those loadsimposed by correctly fitted child re-straints. Under no circumstancesare they to be used for adult seatbelts or harnesses.

APD0836

2-68

Z X

Latch the tether strap hook onto the appro-priate anchor bracket. The tether strapshould be secured to the floor anchorbracket which provides the straightest in-stallation.

Anchor point locationsAnchor point attaching bolts are locatedunder the carpet of the rear luggage areafloor.

WARNINGThe anchor bolt should be installed atall times to prevent the possibility ofexhaust fumes entering the passengercompartment through the holes.

APD0070

2-69

Z X

Installation on front passenger seatWARNING

● Never install a rear-facing child re-straint in the front passenger seat.Supplemental air bags inflate withgreat force. A rear-facing child re-straint could be struck by the supple-mental air bag in a crash and couldseriously injure or kill your child.

● If you install a forward-facing childrestraint in the front passenger seat,place the passenger seat as far backas possible.

A child restraint with a top strap should notbe used in the front passenger seat.

WARNING● The 3-point belt in your vehicle is

equipped with a locking mode re-tractor which must be used wheninstalling a child restraint.

● Failure to use the retractor’s lockingmode will result in the child restraintnot being properly secured. The seatcould tip over or otherwise be unse-cured and cause injury to the child ina sudden stop or collision.

When you install a child restraint in the frontseat, follow these steps:

1. Position the child restraint on the frontpassenger seat. It should be placed ina forward-facing direction only. Movethe seat as far back from the instrumentpanel as possible. Always follow the childrestraint manufacturer’s instructions.Child restraints for infants must beused in the rear-facing direction andtherefore must not be used in the frontseat.



3. Pull on the shoulder belt until all of thebelt is fully extended and a click is heard.At this time, the belt retractor is in theautomatic locking mode (child restraintmode). It reverts back to emergencylocking mode when the belt is fully re-tracted.

4. Allow the belt to retract. A clicking soundis heard as the belt retracts. This indicates

APD0647

2-70

Z X

that the retractor is in the automaticlocking mode. Pull up on the belt toremove any slack in the belt.



7. Check to make sure the child restraint isproperly secured prior to each use. If thelap belt is not locked, repeat steps 3through 6.

After the child restraint is removed and theseat belt is allowed to wind back into theretractor, the automatic locking mode (childrestraint mode) is canceled; the seat beltmay be used as normal and will only lockduring a sudden stop or impact.

INTEGRATED CHILD SAFETYSEATS (if so equipped)

WARNING● Failure to follow the instructions for

the use of these integrated childsafety seats can result in your childstriking vehicle’s interior during asudden stop or crash, causing theinjury or death of your child.

● Improper use of a child restraint canincrease the risk or severity of injuryfor both the child and other occu-pants of the vehicle.

All U.S. states and provinces of Canadarequire that infants and small children berestrained in approved child restraints atall times while the vehicle is being oper-ated.

The optional second row bench seat con-tains two integrated child safety seats.These seats are designed for use only bychildren who weigh between 22 and 60pounds (10-27 kg) and whose height is 45inches (1145 mm) or less and who arecapable of sitting upright alone.

PD1336

2-71

Z X

In addition, these integrated child safetyseats must only be used by children whomeet the following requirements:

● AGE:At least one year old

● SEATED HEIGHT:Top of child’s shoulders must be belowthe shoulder harness openings of theintegrated child seat.

Children smaller than these requirementsshould be restrained in an appropriateseparate child restraint. Children larger thanthese requirements should also be re-strained in an appropriate separate childrestraint or in the appropriate vehicle seatbelt system. Refer to ‘‘Child Restraints forInfants and Small Children’’ and ‘‘Precau-tions On Seat Belt Usage’’ in this chapter forimportant child safety information.

2-72

Z X

Using the Integrated Child SafetySeats

WARNING:● Never use the vehicle seat belts to

restrain a child in an integrated child

safety seat. Use only the shoulder-harness and belt buckle which ispart of the integrated child safetyseat. Never use the integrated childsafety seat as a booster cushionwith the vehicle seat belts.

● Before placing the child in the inte-grated child safety seat, confirm thatthe bench seatback is securelylocked and the seatback release le-ver is in full down position.

● Always make sure the integratedchild safety seat belts are properlypositioned on your child. The childshould sit straight up and backagainst the bench seat. The shoulderharnesses should be centered overthe shoulders and fastened with thechest clip. The belt buckle should bebetween the legs and latched to theshoulder belt tongue. Snugly adjustthe belts around your child. Failureto properly position the child canincrease the risk or severity of injuryto the child in an accident.

CAUTIONRemember that the interior of a closedvehicle can become very hot when leftin direct sunlight. Check the seatingsurface and buckles before placingyour child in the integrated child safetyseat.

APD0855

2-73

Z X

Securing the childBefore using the integrated child safetyseats, carefully read the shoulder har-ness, seatback release, and integratedchild safety seat cushion labels.

The following steps apply to both the leftand right integrated child safety seats.

1. Be sure your child meets all of the re-quired age, weight and height require-ments for the safe use of the integratedchild safety seat.

2. Be sure the second row bench seat issecurely latched to the floor of the ve-hicle. Refer to the ‘‘Flexible seating’’ sec-tion in this chapter for proper seat instal-lation procedures.

3. Be sure the second row bench seatbackis locked by grasping it and trying to rockit back and forth. Also, check that theseatback release lever is in the full downposition. 4. Pull the cushion release strap and lower

the intregrated child safety seat cushioncompletely.

APD0854

2-74

Z X

5. If connected, separate the two halves ofthe shoulder harness from the beltbuckle. Also if connected, disconnect thechest clip and lay the shoulder harnesshalves aside.

6. Place the child on the integrated childsafety seat. Place the belt buckle be-tween the child’s legs.

APD0814 APD0815 APD0816

2-75

Z X

7. Place the left shoulder harness over thechild’s left shoulder. Insert the left shoulderharness tongue into the left side of the beltbuckle. Confirm that the left shoulder har-ness tongue indicator is green. The shoul-der harness tongues only fit into the propersides of the belt buckle.

8. Place the right shoulder harness over thechild’s right shoulder. Insert the right shoul-der harness tongue into the right side of thebelt buckle. Confirm that the right shoulderharness tongue indicator is green. Theshoulder harness tongues only fit into theproper sides of the belt buckle.

9. Fasten the two halves of the chest clipand confirm that the chest clip indicator isgreen. Adjust the chest clip (slightly lowerthan the child’s shoulders) so it comfort-ably holds the shoulder harness in positi-ton on the child’s shoulders.

WARNING● Shoulder harness tongues and chest

clips are equipped with visual indica-tors to confirm proper and securelatching. For the safety of the childand occupants of the vehicle, all indi-

cators must show green before oper-ating the vehicle.

● If the shoulder harness is unfas-tened or not fastened properly, thechild could be seriously injured.

10. Grasp the right shoulder harness abovethe chest clip and pull until the harnessfully extends and a click is heard. At thistime, the harness retractor is in theautomatic locking mode (child restraintmode). With the child sitting properly(straight up and back) in the integrated

APD0817 APD0818 APD0819

2-76

Z X

child safety seat, allow the right shoul-der harness to retract over the rightshoulder and securely restrain the child.A clicking sound is heard as the har-ness retracts, indicating that the retrac-tor is in the automatic locking mode. Besure the left shoulder harness is alsoproperly positioned over the child’s leftshoulder.

11. Check that the shoulder harness is inthe automatic locking mode by trying topull the shoulder harness out of theretractor. If you cannot pull any of theshoulder harness webbing out of theretractor, the shoulder harness is in theautomatic locking mode. If the shoulderharness is not locked, repeat step 10. If,after repeated attempts, the integratedchild safety seat shoulder harness can-not be placed in the automatic lockingmode, do not use the integrated childsafety seat and have it inspected byyour NISSAN dealer.

To cancel the automatic locking mode, un-buckle the chest clip and both shoulderharness tongues. Allow the shoulder har-nesses to retract completely. The automaticlocking mode is now canceled and the

shoulder harness retractor is in the emer-gency locking mode.

WARNING

The automatic locking mode (child re-straint mode) must be reactivated eachtime you place a child in the integratedchild safety seats.

In addition to the automatic locking retrac-tors, the integrated child safety seat shoul-der harnesses are equipped with emer-gency locking retractors. The automaticlocking mode is best to use, especially forchildren who need help staying properlypositioned in the seat and its harnesses (forexample, children who are younger andsmaller), because the belts are alwayslocked. In the emergency locking mode, theshoulder belts only lock in a sudden stop oraccident, allowing a child more freedom ofmovement. Use the emergency lockingmode only if you judge your child able toremain properly positioned in the integratedchild safety seat.

Removing the child1. Release the chest clip.

2. Release the left and right shoulder har-

ness tongues from the belt buckle bypressing the red belt buckle button.

3. Move the left and right shoulder har-nesses aside and assist the child fromthe integrated child safety seat.

Storing the Integrated Child SafetySeat

1. Be sure the shoulder harnesses are fullyretracted and resting inside the inte-grated child safety seat recess. It is notnecessary to reconnect the shoulder har-nesses and belt buckle prior to storingthe integrated child safety seat.

2. While holding onto, but not pulling, thecushion release strap, rotate the cushionupward until it fits flush with the secondrow seat back cushion and locks intoposition.

3. Be sure the integrated child safety seat islocked in the stowed position by graspingthe safety seat cushion and attempting tolower it without pulling the cushion re-lease strap. If the integrated child safetyseat is not locked in the stowed position,repeat steps 1 through 3.

2-77

Z X

Integrated Child Safety Seat main-tenance

● To clean the shoulder harnesses and beltbuckle webbing, apply a mild soap solu-tion or any solution recommended forcleaning upholstery or carpets. Thenbrush the webbing, wipe it with a clothand allow it to dry in the shade. Do notallow the shoulder harnesses to retractuntil they are completely dry.

● The integrated child safety seats clothremovable pads may be cleaned withmild soap and water. The cloth remov-able pads are attached to the seats withfastener strips, and may be easily re-moved. The pads are machine washable.Fo best results, machine wash in coldwater in the gentle cycle. Tumble dry onlow heat. Do not use chlorine bleach, anddo not dry clean.

CAUTIONFailure to follow the washing instruc-tions provided on the cloth removablepads may result in premature wear ordamage.

● Periodically inspect the belt and metalcomponents of the integrated child safetyseats, such as the buckles, tongues,shoulder harness webbings, and latchingindicators. Periodically check the func-tion of the integrated child safety seatshoulder harness retractor functions. Ifloose parts, deterioration, cuts, frays,malfunctions or other damage to the beltwebbings or metal parts are found, seeyour NISSAN dealer for repairs.

Inspection after an accidentIf your vehicle was involved in an accident,before using the integrated child safetyseats, all related components should beinspected by a NISSAN dealer for damage.Damage to the integrated child safety seatsor related components must be repaired.

Push the lock lever down and adjust thesteering wheel up or down to the desiredposition. Pull the lock lever up firmly to lockthe steering wheel in place.

Gently pull down on the wheel to be sure itis properly locked.

WARNINGDo not adjust the steering wheel whiledriving. You could lose control of yourvehicle and cause an accident.

APD0812

TILTING STEERING WHEEL

2-78

Z X

Electric control typeThe outside mirrors operate only when theignition switch is in the ACC or ON position.

Move the switch to select the right or leftside mirror, then adjust using the controllever.

WARNINGObjects viewed in the outside mirror onthe passenger side are closer than theyappear. Be careful when moving to theright. Using only this mirror could

cause an accident. Use the inside mir-ror or glance over your shoulder toproperly judge distances to other ob-jects.

The electric control type outside mirrors canbe heated to defrost, defog, or de-ice forimproved visibility. Press the rear windowdefogger switch to activate the heating func-tion. Press the switch again to deactivate, orit automatically turns off in approximately 15minutes.

Manual control typeThe outside mirror can be moved in anydirection for a better rear view.

WARNINGObjects viewed in the outside mirror onthe passenger side are closer than theyappear. Be careful when moving to theright. Using only this mirror couldcause an accident. Use the inside mir-ror or glance over your shoulder toproperly judge distances to other ob-jects.

APD0808 PD1183M

OUTSIDE MIRROR CONTROL

2-79

Z X

Push the outside mirrors backward to foldthem.

The night position reduces glare from theheadlights of vehicles behind you at night.

WARNINGUse the night position only when nec-essary, because it reduces rear viewclarity.

Your vehicle may be equipped with a driveror passenger side vanity mirror. If the vanitymirror on your vehicle has a cover, accessthe mirror by pulling the sun visor down andlifting the cover up. Some vanity mirrorsilluminate when the mirror cover is opened.

M008 PD1006M AIC0563

OUTSIDE MIRRORS INSIDE MIRROR VANITY MIRROR

2-80

Z X

3 Heater, air conditioner and audio system

Ventilators ..............................................................3-2Heater and air conditioner (manual) ......................3-3Controls ..................................................................3-3Heater operation ....................................................3-4Air conditioner operation ........................................3-5Air flow charts.........................................................3-7Heater and air conditioner (automatic) (if soequipped) .............................................................3-10Automatic operation .............................................3-11Air control buttons ................................................3-11Air conditioner and air recirculation .....................3-12English/metric mode.............................................3-12Rear seat heater and air conditioner (if soequipped) .............................................................3-13

Controls ................................................................3-13Audio system........................................................3-14AM-FM radio with cassette player .......................3-14Tuning ..................................................................3-16Adjusting tone quality ...........................................3-17Cassette tape operations .....................................3-18Antenna ................................................................3-20Compact disc (CD) player (if so equipped) .........3-21Steering wheel controls........................................3-23Rear audio controls ..............................................3-24CB radio or car phone..........................................3-25

Z X

Center ventilatorsOpen, close and adjust the air flow directionof ventilators.

: This symbol indicates a vent is closedwhen the vent switch is rotated down-ward.

: This symbol indicates a vent is openwhen the vent switch is rotated up-ward.

Side ventilators

Open, close and adjust the air flow directionof ventilators.

: This symbol indicates a vent is closedwhen the vent switch is moved to theleft.

: This symbol indicates a vent is openwhen the vent switch is moved to theright.

AHA0590 AHA0591

VENTILATORS

3-2

Z X

WARNING● The air conditioner cooling function

operates only when the engine isrunning.

● Do not leave children, unreliableadults, or pets alone in your vehicle.On hot, sunny days, temperatures ina closed vehicle could quickly be-come high enough to cause severeor possibly fatal injuries to people oranimals.

● Do not use the recirculation modefor long periods as it may cause theinterior air to become stale and thewindows to fog up.

● Positioning of the heater and air con-ditioner controls should not be donewhile driving, in order that full atten-tion may be given to the drivingoperation.

CONTROLS

Fan control dial

This dial controls fan speed.

Temperature control dial

This dial allows you to adjust the tempera-ture of the outlet air.

Air control buttons

These buttons allow you to select the airflow outlets or turn the system off.

OFF buttonThe OFF button shuts off the air supply to alloutlets and stops all fan operations. Use theOFF button to prevent cold air from enteringthe passenger compartment under cold out-side conditions before the engine is warmedup.

Air recirculation buttonFresh position (indicator light off):

Outside air is drawn into the passengercompartment.

AHA0022

HEATER AND AIRCONDITIONER (manual)

3-3

Z X

Use this position for normal heater or airconditioner operation.

Recirculate position (indicator light on):

Interior air is recirculated inside the vehicle.

Activate the air recirculation button whendriving on a dusty road or to help keep outtraffic fumes.

Activate the air recirculation button for im-proved air conditioner performance underhigh temperature and high humidity condi-tions.

If the system is operating in the ormode, the system does not allow the

air recirculate mode to be selected.

CAUTIONDo not use the recirculation mode forlong periods as it may cause the inte-rior air to become stale and the win-dows to fog up.

Air conditioner buttonStart the engine, move the fan control dial tothe desired (1 to 4) position, select an aircontrol button and push the air conditioner

button to turn on the air conditioner. Theindicator light comes on when the air condi-tioner is on. To stop the air conditioner,push the button again; the indicator lightgoes off.

The air conditioner cooling function op-erates only when the engine is running.

HEATER OPERATION

Heating

This mode is used to direct most of the hotair to the floor outlets.

The air recirculation button light should notbe on for normal heating.

1. Push the button in.

2. Turn the fan control dial to select speed.

3. Move the temperature control dial to thedesired position.

Ventilation

This mode directs air to the side and centervents.




NOTE: The recirculate position can beused.

Defrosting or defogging

This mode is used to defrost/defog thewindows.




When the button is pushed, the airconditioner automatically turns on to de-fog the windshield. The recirculated airmode automatically turns off to reducewindow fogging.

When is selected, the air condi-tioner indicator light does not illuminateunless illuminated in the previously se-lected mode. However, the air condi-tioner operates to dehumidify if the out-side temperature is more than 40°F(4°C), whether or not the A/C button hasbeen pressed. Manual selection and illu-mination of the A/C button does not

3-4

Z X

override the automatic dehumidifyingwhich occurs when is selected.

Operating Tips

Clear snow and ice from the wiperblades and air inlet in front of the wind-shield. This improves defrosting/defogging operation.

Bi-level heating/cooling

The bi-level mode directs air to the side andcenter vents and to the floor outlets.

Bi-level is also a cooling mode when highsun load conditions are present with cooltemperatures.

With the A/C system in operation, this modecan be used to cool the passenger’s ordriver’s feet under high temperature condi-tions.

With the A/C system in operation under hightemperature conditions, improved coolingcan be obtained by pushing the recirculationbutton to the on position.

Push the air recirculation button to the offposition when heating is required.


2. Turn the fan control dial to the desiredposition.


Heating and defogging

This mode heats the interior and defogs thewindshield.


2. Turn the fan control dial to the desiredposition.


When the button is pushed, the airrecirculate mode automatically turns off.Outside air is drawn into the passengercompartment to improve the defoggingperformance.

Operating tips● Clear snow and ice from the wiper

blades and air inlet in front of thewindshield. This improves heater op-eration.

● To defog the side windows more effec-tively when in bi-level or ventilation

mode, close the center vent and directthe side vents toward the side windows.

● A slight delay may be experienced whenchanging air control buttons. This is not aproblem, it is only the system motors andsolenoids switching from one outlet toanother.

AIR CONDITIONER OPERATIONStart the engine, move the fan control dial tothe desired (1 to 4) position, and select anair control button before pushing in the airconditioner button to activate the air condi-tioner. When the air conditioner is on, cool-ing and dehumidifying functions are addedto the system operation.

The air conditioner cooling function op-erates only when the engine is running.

NOTE: When switching air flow outlets, theA/C system remains activated unless theA/C button is pressed again to turn it off.The indicator light on the A/C button re-mains illuminated unless the button ispressed to turn it off, or the OFF air controlbutton is pressed.

CoolingThis mode is used to cool and dehumidify.

3-5

Z X



3. Push the air conditioner button. The indi-cator light comes on.


● For quick cooling when the outside tem-perature is high, push the air recirculationbutton on. Be sure to return the air recir-culation button to the off position fornormal cooling.

● Opening the windows helps to vent heatbuildup when parked in the sun.

Dehumidified heatingThis mode is used to heat and dehumidify.

1. Push the air recirculation button to the offposition.



4. Push on the air conditioner button. Theindicator light comes on.


Dehumidified defoggingThis mode is used to defog the windowsand dehumidify.


2. Turn the fan control dial to the desiredspeed.


When the button is pushed, the airconditioner automatically turns on to de-fog the windshield, (however, the lightdoes not illuminate unless illuminated inthe previously selected mode) and therecirculated air mode automatically turnsoff.

Operating tips● Keep windows and sun roof closed while

the air conditioner is in operation.

● After parking in the sun, drive for two orthree minutes with the windows open tovent hot air from the passenger compart-ment. Then, close the windows. Thisallows the air conditioner to cool theinterior more quickly.

● The air conditioning system should be

operated for about ten minutes atleast once a month. This helps pre-vent damage to the system due to lackof lubrication.

● If the coolant temperature gauge ex-ceeds the H (hot) position, turn the airconditioner off. See ‘‘If your vehicle over-heats’’ in the ‘‘In case of emergency’’section for additional information.

3-6

Z X

AIR FLOW CHARTSThe following charts show the button anddial positions for MAXIMUM AND QUICKheating, cooling or defrosting. The air recir-culation switch should always be in theoff position for heating and defrosting.

AHA0801

3-7

Z X

AHA0802

3-8

Z X

AHA0800

3-9

Z X

WARNING● The air conditioner cooling function

operates only when the engine isrunning.

● Do not leave children, unreliableadults, or pets alone in your vehicle.On hot, sunny days, temperatures ina closed vehicle could quickly be-come high enough to cause severeor possibly fatal injuries to people oranimals.

● Do not use the recirculation modefor long periods as it may cause theinterior air to become stale and thewindows to fog up.

● Positioning of the heater and air con-ditioner controls should not be donewhile driving, in order that full atten-tion may be given to the drivingoperation.

The Electronic Automatic TemperatureControl (EATC) is located at the center ofthe instrument panel, above the radio. TheEATC operates only when the ignition is

turned to the ON position.

The EATC maintains the temperature youselect and controls the airflow for your com-fort. It also allows you to override the auto-matic operation with manual function selec-tor buttons.

To turn the EATC on, push either the AU-TOMATIC button or any of the five functionselector buttons: , , ,

, or . To turn the EATC off,press the OFF button.

When you select AUTOMATIC, the systemdetermines fan speed, airflow location anddischarge air temperature. When one of thefunction selector buttons is pressed, yourselection determines airflow location only.Fan speed and discharge air temperatureremain automatic. You can override fanspeed by rotating the vertical thumbwheel

located at the extreme right of thecontrol panel.

The display window indicates the status ofthe system. It shows the selected tempera-ture and AUTO when in the AUTOMATICmode. It also indicates manual (thumb-wheel) control of the fan speed when a

is shown.

AHA0592

HEATER AND AIR CONDITIONER(automatic) (if so equipped)

3-10

Z X

AUTOMATIC OPERATIONPush the AUTOMATIC button and selectthe desired temperature. The selected tem-perature and AUTO show in the displaywindow. The EATC heats or cools toachieve the set temperature.

When in AUTOMATIC and weather condi-tions require heat, air is sent to the floor.However, a feature is included in the EATCto prevent blowing cold air to the floor if theengine coolant is not warm enough to allowheating. In three or four minutes the fanspeed gradually increases and airflowchanges to the floor.

If unique conditions exist, such as windowfogging, the five override buttons allow spe-cific airflow selection. The thumbwheel al-lows you to adjust the fan speed to suit yourneeds.

Temperature selectionThe TEMP button on the leftside of the control panel is for temperatureselection. The side lowers the settemperature, and the side raises theset temperature. Press and hold either sideof the button to rapidly change the tempera-ture setting in one degree increments to

either 65°F (18°C) or 85°F (29°C). If youwant continuous maximum cooling, pushthe side of the TEMP button until60°F (16°C) shows in the display window.The EATC cools at maximum and disre-gards the 60°F (16°C) setting until a warmertemperature is selected. If you want con-tinuous maximum heating, push the

side of the TEMP button until 90°F(32°C) shows in the display window. TheEATC provides maximum heat regardlessof the 90°F (32°C) setting until a coolertemperature is selected.

Fan speed and thumbwheelYour EATC automatically adjusts the fanspeed to the existing conditions. To controlthe fan speed yourself, use the thumbwheellocated at the extreme right side of theEATC control panel. Using the thumbwheelcancels the automatic fan speed control,and causes a to appear in the displaywindow. Rotate the thumbwheel up for HIspeeds and down for LO speeds.

To return to auto fan control, press theAUTOMATIC button.

AIR CONTROL BUTTONSYour EATC has five buttons which allow you

to make special selections. The buttons aregrouped in the middle of the EATC paneland allow you to determine airflow location.Pressing any of the air control buttonschanges airflow location only, and does notaffect the ability of the system to controltemperature or fan speed. Return to fullyautomatic operation by pushing the AUTO-MATIC button.

Push this button for airflow to the floor andwindshield at the same time. The in-dicator light comes on, and the displaywindow shows the set temperature.

Press this button to obtain maximum airflowto the windshield. Adjust the temperaturesetting as required for defrosting. The

indicator light comes on, and thedisplay window shows the set temperature.When the outside temperature is about50°F (10°C) or above, the air is dehumidi-fied to prevent window fogging.

Push this button to select airflow throughthe instrument panel registers. The

indicator light comes on, and thedisplay window shows the set temperature.

3-11

Z X

The EATC heats the air if the selectedtemperature is warmer than the outside aircoming into the vehicle. However, the air isnot cooled regardless of the temperaturesetting.

Push this button to get air from the floor andinstrument panel registers at the same time.The indicator light comes on and thedisplay window shows the set temperature.Depending on the selected temperature, theair is automatically heated or cooled.

Push this button to direct airflow to the floor.The indicator light comes on, and thedisplay window shows the set temperature.The air cannot be cooled in the

mode, only heated.

AIR CONDITIONER AND AIR RE-CIRCULATIONActivate the air conditioner in any of theoverride modes listed above by pressing theA/C button. The A/C indicator light comeson to verify activation, and cooled air flowsfrom the vents. Fan speed continues to becontrolled by the EATC unless the fanspeed thumbwheel is used to override.

Press the button to choose air recir-culation. In this mode the EATC systemrecirculates the air inside the vehicle ratherthan drawing air from outside. Use thismode together with the air conditioner torapidly cool the inside of the vehicle, or todehumidify the air inside the vehicle.

ENGLISH/METRIC MODESwitch from English to metric temperaturedisplay by simultaneously pressing the

and A/C buttons and holding thethumbwheel in upper position (HI) for onesecond.

AHA762

3-12

Z X

To operate the rear seat heater and airconditioner, the engine must be running.

The rear seat heater and air conditioner canbe turned on and off from the front controls. Ifthe rear seat fan control lever on the frontpanel is set to OFF, the rear heater and airconditioner is turned off. If it is set to any ofthe fan speed positions, air is dischargedfrom the rear vents at the correspondingspeed. When the rear seat fan control leveron the front panel is set to REAR, the rearseat passengers control their own fan speed.

The rear seat air conditioner only works whenthe front seat air conditioner is operating.

CONTROLS

Fan control dialThis dial turns the fan on and off, andcontrols fan speed.

Temperature control dialThis dial allows you to adjust the tempera-ture of the outlet air. A slight delay intemperature change may be experiencedwhile the climate control system warms up.

● On vehicles equipped with Electronic Au-tomatic Temperature Control (EATC), out-let air temperature is automatically con-

trolled when the rear seat fan control leveron the front panel is set to 1, 2, 3, or 4.

Vent switch

The vent switch allows you to select air flowfrom the upper or lower vents.

● A slight delay may be experienced whenchanging the vent selection. This is not aproblem; the delay is only the systemmotors and solenoids switching from oneoutlet to another.

AHA0555

REAR SEAT HEATER AND AIRCONDITIONER (if so equipped)

3-13

Z X

Servicing air conditioningThe air conditioning system in your NISSANvehicle is charged with a refrigerant de-signed with the environment in mind.

This refrigerant does not harm theearth’s ozone layer.

Special charging equipment and lubricantare required when servicing your NISSANair conditioner. Using improper refrigerantsor lubricants causes severe damage to yourair conditioning system. See ‘‘Air condition-ing system refrigerant and lubricant recom-mendations’’ in the ‘‘Technical and con-sumer information’’ section of this manual.

Your NISSAN dealer is able to service yourenvironmentally ‘‘friendly’’ air conditioningsystem.

To turn the radio on, turn the ignition key toACC or ON. If you listen to the radio with theengine not running, turn the key to the ACCposition.

Radio reception is affected by station signalstrength, distance from radio transmitter,buildings, bridges, mountains and other ex-ternal influences. Intermittent changes inreception quality normally are caused bythese external influences.

ClockFor information on setting the clock, refer tothe section ‘‘Instruments and controls’’.

AM-FM RADIO WITH CASSETTEPLAYER

Radio operationPush the VOL-PUSH ON knob to turn theradio on. Push the VOL-PUSH ON knobonce more to turn the radio off.

Turn the knob to adjust the volume.

Inserting a cassette tape into the cassetteplayer while the radio is on turns the radiooff and turns the cassette player on.

AUDIO SYSTEM

3-14

Z X

AHA0593

3-15

Z X

TUNING

WARNING

The radio should not be tuned whiledriving in order that full attention maybe given to the driving operation.

AUTO SET (if so equipped)

Press AUTO SET while listening to the radioto activate the Auto Memory Store feature.

When AUTO SET is depressed for less thanthree seconds, the display window momen-tarily indicates AUTO, and the radio seeksthe first six strong stations for the respectiveband. The first six strong stations are thenstored in order in memory buttons 1 through6.

Only stations in the selected band are set,and the station seek begins from the lastfrequency stored in memory button 6. If AM,FM, SCAN, TUNE, SEEK, AUTO SET, or amemory button is pushed while AutoMemory Store is operating, AUTO SET iscanceled and AUTO OFF shows in thedisplay window.

AHA0594

3-16

Z X

SEEK tuning

This feature on your radio allows you toautomatically select strong frequency sta-tions up or down the frequency band. PressSEEK to select the next strong sta-tion up the frequency band. Press SEEK

to select the next strong station downthe frequency band. To change frequenciesquickly, press and hold either side of theSEEK button.

SCAN tuning

Push SCAN to enter the scan tuning mode.The radio searches up the frequency band,stopping and playing each strong frequencystation for five seconds. This continues untilthe SCAN button is pushed a second timeor a different tuning function is selected.The AM or FM1 or FM2 symbol in thedisplay window flashes while each station isbeing played.

AM/FMPress the AM/FM button to select the de-sired band: AM, FM1, or FM2. The stereoindicator shows in the display window dur-ing FM stereo reception. When the stereobroadcast signal is weak, the radio auto-

matically changes from stereo to monauralreception.

Station memory operations

Your radio comes equipped with sixmemory buttons, which are used to presetup to six AM stations and 12 FM stations.

NOTE: If the vehicle’s battery is discon-nected, the memory buttons need to bereset.

To set the memory buttons:

1. Select the desired band (AM, FM1, orFM2) by pressing the AM/FM button.

2. Tune to the desired frequency.

3. Press one of the memory buttons andhold the button in. The sound mutes outfor about two seconds, then returns. Thatstation is now held in memory on thatbutton.

Repeat the three steps above for eachmemory button you want to set.

The memory buttons also control the rearaudio controls. Push memory buttons 3 and5 simultaneously to turn the rear audiocontrols on. Push them again to turn therear audio controls off. A headphone sym-

bol appears in the display window when therear controls are activated.

ADJUSTING TONE QUALITY

BASS

Bass control allows you to adjust the lower,bass frequencies to your preference.

Push the BASS button either or; BASS and the setting indicator bar

appear in the display window. Pressing theBASS button either or in-creases or decreases the level of bass, asindicated by the number of bar segmentsshowing in the display window.

Following bass adjustment, the display win-dow shows the current setting for threeseconds, then returns to the display prior toadjustment.

TREBTreble control allows you to adjust thehigher, treble frequencies to your prefer-ence.

Push the TREB button either or; TREB and the setting indicator bar

appear in the display window. Pressing theTREB button either or in-

3-17

Z X

creases or decreases the level of treble, asindicated by the number of bar segmentsshowing in the display window.

Following treble adjustment, the displaywindow shows the current setting for threeseconds, then returns to the display prior toadjustment.

BALBalance control allows you to adjust thesound distribution between the right and leftspeakers.

Push the BAL button either or; BAL and the setting indicator bar

appear in the display window. Press theBAL button to shift the sound to theright speakers. The single indicator barmoves to the right of the display window.Press the BAL button to shift thesound to the left speakers. The single indi-cator bar moves to the left of the displaywindow. When the indicator bar is in thecenter position the sound is equally distrib-uted between the right and left speakers.

Following balance adjustment, the displaywindow shows the current setting for threeseconds, then returns to the display prior toadjustment.

FADEFader control allows you to adjust sounddistribution between the front and rearspeakers.

Push the FADE button either or; FADE and the setting indicator bar

appear in the display window. Press theFADE button to shift the sound to thefront speakers. The single indicator barmoves to the right of the display window.Press the FADE button to shift thesound to the rear speakers. The singleindicator bar moves to the left of the displaywindow. When the indicator bar is in thecenter position the sound is equally distrib-uted between the front and rear speakers.

Following fader adjustment, the display win-dow shows the current setting for threeseconds, then returns to the display prior toadjustment.

CASSETTE TAPE OPERATIONSTurn the ignition key to ACC or ON, theninsert the cassette tape into the tape doorby lightly pushing it. Because of the powerloading feature, the cassette tape is auto-matically pulled into the player and beginsto play.

CAUTION

Do not force the cassette tape into thetape door. This could damage theplayer.

When a cassette is inserted into the audiosystem, the word TAPE and a cassette sidesymbol (either 1 or 2) illuminate in thedisplay window.

A cassette tape can be loaded with theignition ON whether or not the radio poweris on. Inserting a cassette tape with theradio power off causes the audio system toturn on. After the cassette is ejected, theaudio system turns off. Also, the powerantenna (if so equipped) stays in the downposition during cassette tape operation.

The cassette tape automatically changesdirections to play the other side when thefirst side is completed.

● To maintain good quality sound,NISSAN recommends using cassettetapes of 60 minutes or shorter inlength.

● Cassette tapes should be removedfrom the player when not in use. Store

3-18

Z X

cassettes in their protective casesand away from direct sunlight, heat,moisture, and magnetic sources.

● Direct sunlight can cause the cassetteto become deformed. The use of de-formed cassettes may cause the cas-sette to jam in the player.

● Do not use cassettes with peeling orloose labels, as the label could jam inthe player.

● If a cassette has loose tape, insert apencil through one of the cassettehubs and rewind the tape firmlyaround the hubs. Loose tape maycause tape jamming and waveringsound quality.

● Over a period of time, the playbackhead, capstan, and pinch roller maycause a tape coating residue as thetape passes over the head. This resi-due accumulation can cause weak orwavering sound, and should be re-moved periodically with a head clean-ing tape.

If the residue is not removed periodi-cally, the player may need to be dis-assembled for cleaning.

Use a Nissan Cassette Deck Cleaning Sys-tem or equivalent to clean the tape playerhead after 10-12 hours of play to helpmaintain the best playback sound andproper tape operation.

REW and FF

Push the REW (rewind) or FF (fast forward)button for the desired direction. When usingREW, push the FF button momentarily tostop the tape and resume playing. Similarly,when using FF, push the REW button mo-mentarily to stop the tape and resume play-ing.

Automatic Music Search (AMS)

Pushing the SEEK button while playing acassette tape activates the Automatic MusicSearch (AMS) mode. Press SEEK torewind the tape to the previous selection, orpress SEEK to forward the tape tothe next selection.

This system searches for the blank intervalsbetween selections. If there is a blank inter-val within one program or there is no intervalbetween programs, the system may notstop in the desired or expected location.

Changing the direction of tape playPress the SIDE 1-2 button to reverse thetape to the opposite track. The display win-dow indicates the track being played with a1 or 2.

Stopping and ejecting the cassettetapePush the EJ button. The cassette tapeautomatically ejects from the player and theradio turns off. A tape may be ejected withthe ignition switch in the ON or OFF posi-tion.

Dolby NR (noise reduction)Push the button for Dolby NR en-coded tapes to reduce high frequency tapenoise. When activated, a appears inthe display window.

Dolby NR is manufactured under licensefrom Dolby Laboratories Licensing Corpora-tion. ‘‘Dolby NR’’ and the double-D symbolare trademarks of Dolby Laboratories Li-censing Corporation.

3-19

Z X

Manual antennaThe manual antenna on your vehicle re-mains in the up position at all times. Theantenna cannot be shortened, but can beremoved. When you need to remove theantenna, turn its base counterclockwise.

Power antenna (if so equipped)The power antenna automatically extendswhen the radio is turned on, and retractswhen turned off or when a tape or CD isplayed. If the radio is left on, the antennaretracts and extends with the ignition keyOFF-ON operation.

CAUTION● Before turning the radio on, make

sure that there is no one near theantenna outlet and there is enoughspace for it to extend.

● To prevent damage, be sure that thepower antenna is fully retracted be-fore the vehicle enters an automatedcar wash.

● Dirt and other foreign matter on thepower antenna rod may interrupt itsoperation. Clean the rod periodicallywith a damp cloth. This type ofcleaning is especially important dur-ing the winter seasons in areaswhere road salt and other chemicalsmay be spread on the road surfacesand splashed onto the antenna rod.

ANTENNA

3-20

Z X

COMPACT DISC (CD) PLAYER(if so equipped)

NOTE: Audio control features include com-mand buttons for CD players which can beinstalled as optional equipment to upgradethe audio system. A CD player is not in-cluded with this system, but can be pur-chased as an option at any time. Consultwith your NISSAN dealer for feature avail-ability.

The compact disc player consists of twomain components, the 6 CD magazine andthe CD changer. Both components are lo-

cated on the center instrument panel con-sole, below the ashtray.

How to load the CD magazine

To load the magazine with CDs, first pushthe button on the CD changer to ejectthe magazine, then remove the magazinefrom the changer. The inside of the CDmagazine contains six shelves, one foreach CD to be loaded. Carefully slide a CD(label side up) onto one of the shelves andpush it in. Repeat as desired, loading up tosix CDs.

CD magazine insert

Once the desired number of CDs are loadedinto the magazine, insert the magazine backinto the CD changer.

With the ignition switch OFF, the CD maga-zine loads into the CD changer. Once theignition switch is turned to ACC or ON, theaudio system returns to its previous mode.

With the ignition switch in the ACC or ONposition, the CD magazine loads into theCD changer and begins play with disc 1,track 1.

CD player controls

BASS, TREB, BAL, AND FADE

The bass, treble, balance, and fader con-trols for the CD player are the same asthose for the radio and cassette tape player.Refer to the ‘‘Adjusting tone quality’’ sectionfor operating instructions on these controls.

CD

Push this button to switch from radio or tapemode to CD mode. CD play begins auto-matically if at least one disc is loaded in themagazine. The display window shows the

AHA0597

3-21

Z X

CD number for three seconds, then thetrack number for three seconds, then dis-plays both together for the remainder of thetrack.

Push this button when a CD is alreadyplaying to stop the CD.

If the CD button is pushed while in the radioor tape mode, and there are no CDs loadedin the magazine, the display window flashesa NO DISC message for 4 seconds.

SEEKPush SEEK to select the previoustrack number, or push SEEK to se-lect the next track number. After the lasttrack on a disc, pushing SEEK se-lects the first track of the same disc.

TUNE DISCSPush TUNE DISCS to select the pre-vious CD in the magazine. Push TUNEDISCS to select the next CD in themagazine.

SCANPush this button to audition the first 10seconds of each track on a disc. At the endof the disc, the SCAN function continues

with the first track on the same disc. Thedisplay window flashes the track numberbeing auditioned during the SCAN function.

REW

Press this button to reverse the CD mecha-nism and move back to a previous point onthe disc. If held for less than three seconds,this button causes the CD to reverse atthree times the normal play speed. If heldfor more than three seconds, the CD re-verses at 10 times the normal play speed.

The mechanism reverses to the beginningof track 1 and begins play if the button isheld continuously. The volume decreasesand the display window shows the elapsedtime during the entire fast reverse period.

FFPress this button to advance the CD mecha-nism and move ahead on the disc. If held forless than three seconds, this button causesthe CD to advance at three times the normalplay speed. If held for more than threeseconds, the CD advances at 10 times thenormal play speed.

The volume decreases and the display win-dow shows the elapsed time during the

entire fast forward period.

COMP

Press this button to activate the compres-sion function. This function reduces thedynamic range of the CD program material,which provides the listener with a moreconsistent level of volume. The display win-dow shows a C when the compressionfunction is activated.

SHUFFLE

Press this button to randomly select the playorder of the tracks on a CD. When all tracksof one CD have been played, the systemchanges to the next CD in the magazineand proceeds to play the tracks in a ran-domly selected order. The shuffle featureremains in effect until turned off by pressingthe SHUFFLE button again.

When the shuffle function is activated, thedisplay window shows the letters SHF for twoseconds, then shows the disc number andtrack selected for the remainder of that selec-tion. When a new track is selected, the lettersSHF reappear for two seconds, followed bythe new disc and track number, and so on, aslong as the shuffle function is active.

3-22

Z X

STEERING WHEEL CONTROLS

The radio controls mounted on the right sideof the steering wheel provide convenientaccess to three commonly used functions:

VOL, VOL, and NEXT. Usethe NEXT button to select the next pre-programmed station (AM/FM), the next se-lection on the tape, or the next selection onthe CD.

AHA0803

3-23

Z X

REAR AUDIO CONTROLS

Radio features controlled by the rear seatremote control (if so equipped) are listedbelow:

● Volume: −/+

● Program advance: proceed to the nextpreset station (AM/FM), the other side ofthe tape, or the next CD.

● Source select: AM/FM, tape, or CD

● Speakers ON/OFF

● Seek: b c

Push the Memory 3 and Memory 5 buttonson the front radio controls simultaneously toturn the rear controls on. Push them againto turn the rear audio controls off.

The headphones symbol illuminates in thefront display when the rear audio controlsare on. Two headphone jacks are providedso two rear seat passengers may listen tothe audio system privately.

The rear controls can only increase thevolume to the level which the front radio isset.

Headphones are not included with the ve-

hicle. Most portable radio headphones workwith the rear audio controls.

When the rear seat controls are on, pushthe SPKRS ON-OFF button to turn allspeakers off. Push again to turn all speak-ers on.

If the rear audio system was on when theignition was turned OFF, the audio system‘‘remembers’’ and the rear system is still onwhen the engine is started again. The sys-tem also ‘‘remembers’’ if the speakers wereON or OFF. Therefore, the speakers mayhave to be turned on again with the SPKRSON-OFF button.

AHA0595

3-24

Z X

Microphone installed modelIf equipped with a genuine cellular phone,your NISSAN features a non-directional mi-crophone in the steering column cover, so itis not necessary to look at or speak directlyinto the microphone when calling.

To do so could detract from the drivingoperation and cause an accident.

See the manual for car phone operation.

Pre-wired and antenna for phoneinstalled modelSome models are pre-wired to accept thegenuine NISSAN cellular phone.

In addition, the same model has the phoneantenna built into the rear glass window.

When installing a CB ham radio, a carphone or other transmitters in your NISSAN,be sure to observe the following cautions,otherwise the new equipment may ad-versely affect the MFI system and otherelectronic parts.

CAUTION

● Keep the antenna as far away aspossible from the Engine ControlModule.

● Also keep the antenna wire morethan 8 inches (20 cm) away from theMultiport Electronic Fuel Injection(MFI) harness. Do not route the an-tenna wire next to any harness.

● Adjust the antenna standing-waveratio as recommended by themanufacturer.

● Connect the ground wire from theCB radio chassis to the body.

● For details, consult a NISSAN dealer.

CB RADIO OR CAR PHONE

3-25

Z X

Z X

4 Starting and driving

Precautions when starting and driving...................4-2Exhaust gas (carbon monoxide) ............................4-2Three way catalyst .................................................4-2Avoiding collision and rollover................................4-3Drinking alcohol/drugs and driving.........................4-3Ignition switch.........................................................4-4Before starting the engine......................................4-5Driving with an automatic transmission .................4-5Overdrive switch.....................................................4-7Starting the engine.................................................4-8

Parking brake operation.........................................4-9Cruise control .......................................................4-10Break-in schedule ................................................4-12Increasing fuel economy ......................................4-12Parking/parking on hills ........................................4-13Power steering system.........................................4-14Brake system........................................................4-14Anti-lock brake system (ABS)(if so equipped) ....................................................4-15Cold weather driving ............................................4-16

Z X

WARNING

Do not leave children, unreliableadults, or pets alone in your vehicle.They could accidently injure them-selves or others through inadvertentoperation of the vehicle. Also, on hot,sunny days, temperatures in a closedvehicle could quickly become highenough to cause severe or possiblyfatal injuries to people or animals.

EXHAUST GAS(Carbon Monoxide)

WARNINGDo not breathe exhaust gases; theycontain colorless and odorless carbonmonoxide. Carbon monoxide is dan-gerous. It can cause unconsciousnessor death.

● If you suspect that exhaust fumesare entering the vehicle, drive withall windows fully open, and have thevehicle inspected immediately.

● Do not run the engine in closedspaces such as a garage for anylonger than is absolutely necessary.

● Do not park the vehicle with the en-gine running for any extended lengthof time.

● Keep the rear door and flip-up rearwindow closed while driving, other-wise exhaust gases could be drawninto the passenger compartment. Ifyou must drive in this manner forsome reason, take the followingsteps.

1. Open all the windows.

2. Set the air recirculate switch to offand the fan control dial at 4 (high)to circulate the air.

● If electrical wiring or other cableconnections must pass to a trailerthrough a seal on the body, followthe manufacturer’s recommendationto prevent carbon monoxide entryinto the vehicle.

● The exhaust system and bodyshould be inspected by a qualifiedmechanic whenever:

a. The vehicle is raised for service.

b. You suspect that exhaust fumesare entering into the passengercompartment.

c. You notice a change in the soundof the exhaust system.

d. You have had an accident involv-ing damage to the exhaust system,underbody, or rear of the vehicle.

THREE WAY CATALYST

The three way catalyst is an emission con-trol device installed in the exhaust system.Exhaust gases in the three way catalyst areburned at high temperatures to help reducepollutants.

WARNING

● The exhaust gas and the exhaustsystem are very hot. Keep people orflammable materials away from theexhaust pipe.

● Do not stop or park the vehicle overflammable materials such as drygrass, waste paper or rags. Theymay ignite and cause a fire.

PRECAUTIONS WHENSTARTING AND DRIVING

4-2

Z X

CAUTION● Do not use leaded gasoline. Depos-

its from leaded gasoline will seri-ously reduce the three way cata-lyst’s ability to help reduce exhaustpollutants.

● Keep your engine tuned up. Malfunc-tions in the ignition, fuel injection, orelectrical systems can cause over-rich fuel flow into the catalyst, caus-ing it to overheat. Do not keep driv-ing if the engine misfires, or ifnoticeable loss of performance orother unusual operating conditionsare detected. Have the vehicle in-spected promptly by an authorizedNISSAN dealer.

● Avoid driving with an extremely lowfuel level. Running out of fuel couldcause the engine to misfire, damag-ing the three way catalyst.

● Do not race the engine while warm-ing it up.

● Do not push or tow your vehicle tostart the engine.

AVOIDING COLLISION ANDROLLOVER

WARNINGFailure to operate this vehicle in a safeand prudent manner may result in lossof control or an accident.

Be alert and drive defensively at all times.Obey all traffic regulations. Avoid excessivespeed, high speed cornering, or suddensteering maneuvers, because these drivingpractices could cause you to lose control ofyour vehicle. As with any vehicle, a lossof control could result in a collision withother vehicles or objects, or cause thevehicle to rollover, particularly if the lossof control causes the vehicle to slidesideways. Be attentive at all times, andavoid driving when tired. Never drive whenunder the influence of alcohol or drugs(including prescription or over-the-counterdrugs which may cause drowsiness). Al-ways wear your seat belt as outlined in the‘‘Seat Belts’’ section of this manual, andalso instruct your passengers to do so.

WARNINGNever drive under the influence of alco-hol or drugs. Alcohol in the blood-stream reduces coordination, delaysreaction time and impairs judgement.Driving after drinking alcohol increasesthe likelihood of being involved in anaccident injuring yourself and others.Additionally, if you are injured in anaccident alcohol can increase the se-verity of the injury.

NISSAN is committed to safe driving. How-ever, you must choose not to drive underthe influence of alcohol. Every year thou-sands of people are injured or killed inalcohol related accidents. Although the locallaws vary on what is considered to belegally intoxicated, the fact is alcohol affectsall people differently and most people un-derestimate the effects of alcohol.

Remember, drinking and driving don’t mix!

And that’s true for drugs, too (over thecounter, prescription, and illegal drugs).Don’t drive if your ability to operate yourvehicle is impaired by alcohol, drugs, orsome other physical condition.

DRINKING ALCOHOL/DRUGSAND DRIVING

4-3

Z X

The ignition switch includes an anti-theftsteering lock device.

The key can only be removed when theignition switch in the LOCK position.

The ignition lock is designed so the keycannot be turned to LOCK and removeduntil the shift lever is moved to the P (Park)position.

The shift lever is designed so it cannot bemoved out of P (Park) and into any of theother gear positions if the ignition key isturned to LOCK, or if the key is removedfrom the switch.

The shift lever can be moved out of P(Park) after the ignition switch is in theON position, and the foot brake pedal isdepressed.

To lock the steering wheel, remove thekey. To unlock the steering wheel, insertthe key and turn it gently while rotatingthe steering wheel slightly right and left.

WARNING

Never remove the key while driving. Ifthe key is removed, the steering wheelwill lock. This may cause the driver tolose control of the vehicle and couldresult in serious vehicle damage orpersonal injury.

Key positions

LOCK (Normal parking position)

OFF

The engine can be turned off without lockingthe steering wheel, if the key is left in theignition.

ACC (Accessories)

This position activates electrical accesso-ries such as the radio when the engine isnot running.

ON (Normal operating position)

This position turns on the ignition systemand the electrical accessories.

START

This position activates the starter motor,which starts the engine.

ASD0560

IGNITION SWITCH

4-4

Z X

● Make sure the area around the vehicle isclear.

● Maintenance items listed here should bechecked periodically (for example, eachtime you check engine oil).

● Check that all windows and lights areclean.

● Visually inspect tires for their appearanceand condition. Also check tires for properinflation.

● Lock all doors.

● Position seat and adjust head restraints.

● Adjust inside and outside mirrors.

● Fasten seat belts and ask all passengersto do likewise.

● Check the operation of warning lightswhen key is turned to the ON position.

The automatic transmission in your vehicleis electronically controlled by a microcom-puter to produce maximum power andsmooth operation.

Shown on the following pages are the rec-ommended operating procedures for thistransmission. Follow these procedures formaximum vehicle performance and drivingenjoyment.

Starting the vehicle

● After starting the engine, fully depress thefoot brake pedal before shifting the selec-tor lever to the R, N, D, 2 or 1 position. Besure the vehicle is fully stopped beforeattempting to shift the selector lever.

This automatic transmission is designedso the foot brake pedal MUST be de-pressed before shifting from P to any driveposition while the ignition switch is ON.

The shift lever cannot be moved out of Pand into any of the other gear positions ifthe ignition key is turned to ACC, LOCK,or if the key is removed from the switch.

When the battery charge is low, the shiftlever can be moved if the ignition switchis in the ACC position.

1. Keep the foot brake pedal depressed andshift into a driving gear.

2. Release the parking brake and footbrake, then gradually start the vehicle inmotion.

WARNING● Do not depress the accelerator pedal

while shifting from P or N to: R, D,2 or 1. Always depress the brakepedal until shifting is completed.Failure to do so could cause you tolose control and have an accident.

● Cold engine idle speed is high, souse caution when shifting into a for-ward or reverse gear before the en-gine has warmed up.

● Never shift to P or R while the ve-hicle is moving. This could cause anaccident.

● On slippery roads, do not downshift.This may cause a loss of control.

BEFORE STARTING THEENGINE

DRIVING WITH ANAUTOMATIC TRANSMISSION

4-5

Z X

CAUTIONWhen stopping the vehicle on an uphillgrade, do not hold the vehicle by de-pressing the accelerator pedal. Thefoot brakes should be used for thispurpose.

Shifting with automatic transmission

P (Park):

Use this selector position when the vehicleis parked or when starting the engine. Al-ways be sure the vehicle is at a completestop. For maximum safety, depress thebrake pedal, pull the lever toward you, andmove the lever to the P position. Apply theparking brake. When parking on a hill, applythe parking brake first, then shift the leverinto the P position.

Shifting from P (Park)If the ignition switch is in the ON positionand the foot brake pedal is depressed, butthe shift lever still cannot be moved out of P(Park), follow these instructions:

1. Shut the engine off and remove the key.

2. Apply the parking brake.

3. Reinsert the ignition key and turn it clock-wise to the first position (ACC).

4. Depress the brake pedal, move the gear-shift lever to N (Neutral) and start theengine.

R (Reverse):

Use this position to back up. Always be surethe vehicle is completely stopped. Depressthe brake pedal, then pull the shift levertoward you and move it to the R position.

ASD0552

4-6

Z X

N (Neutral):

Neither forward nor reverse gear is en-gaged. The engine can be started in thisposition. You may shift to N and restart astalled engine while the vehicle is moving.

D (Drive):

Use this position for all normal forwarddriving.

2 (Second gear):

Use for hill climbing or engine braking ondownhill grades.

Do not downshift into 2 at speeds over 63MPH (100 km/h). Do not exceed 63 MPH(100 km/h) in 2.

1 (Low gear):

Use 1 when climbing steep hills slowly ordriving slowly through deep snow, sand ormud, or for maximum engine braking onsteep downhill grades.

Do not exceed 38 MPH (60 km/h) in 1.

Do not shift into 1 at speeds over 38 MPH(60 km/h).

Accelerator downshift— In D position —

For rapid passing or hill climbing, fully depressthe accelerator pedal to the floor. This shifts thetransmission down into third gear, second gearor first gear, depending on the vehicle speed.

Fail-safeWhen the Fail-safe operation occurs, thenext time the key is turned to the ONposition, the O/D OFF light blinks for ap-proximately 8 seconds after coming on for 2seconds. While the vehicle can be drivenunder these circumstances, please notethat the gears in the automatic transmissionwill be locked in 3rd gear.

NOTE: If the vehicle is driven under extremeconditions, such as excessive wheel spinningand subsequent hard braking, the Fail-safesystem may be activated. This will occur evenif all electrical circuits are functioning prop-erly. In this case, turn the ignition key OFFand wait for 3 seconds. Then turn the keyback to the ON position. The vehicle shouldreturn to its normal operating condition. If itdoes not return to its normal operating condi-tion, have your NISSAN dealer check thetransmission and repair, if necessary.

OVERDRIVE SWITCH

Each time your vehicle is started, the trans-mission is automatically ‘‘reset’’ to overdriveON.

ON: For normal driving the overdriveswitch is engaged. The transmissionis upshifted into overdrive as thevehicle speed increases.

The overdrive does not engage until theengine has warmed up.

OFF: For driving up and down long slopeswhere engine ‘‘braking’’ would beadvantageous, push the overdriveswitch. The O/D OFF light illumi-

ASD0561

4-7

Z X

nates. When cruising at a low speedor climbing a gentle slope, you mayfeel uncomfortable shift shocks asthe transmission shifts between 3rdand overdrive repeatedly. In thiscase, press the overdrive switch.The O/D OFF indicator light comeson at this time.

When driving conditions change, press theoverdrive switch again. The O/D OFF indi-cator light goes out.

Remember not to drive at high speeds forextended periods of time with the O/D OFFlight illuminated. This reduces the fueleconomy.

1. Apply the parking brake.

2. Move the selector lever to P (Park) or N(Neutral). (P preferred.)

The shift lever cannot be moved out ofP and into any of the other gear posi-tions under the following conditions:

● The ignition key is turned to theOFF position.

● The ignition key is turned to the ONposition without depressing thefoot brake pedal.

The starter is designed not to operateif the selector lever is in one of thedriving positions.

3. Crank the engine with your foot off theaccelerator pedal by turning the ignitionkey to START. Release the key when theengine starts. If the engine starts, butfails to run, repeat the above procedure.

— If the engine is very hard to start inextremely cold or hot weather, de-press the accelerator pedal and hold itto help start the engine.

— In the summer, when restarting theengine within 30 minutes after it hasbeen stopped, keep the acceleratorpedal slightly depressed while start-ing.

CAUTIONDo not operate the starter for more than15 seconds at a time. If the engine doesnot start, turn the key off and wait 10seconds before cranking again, other-wise the starter could be damaged.

4. Warm-up

Allow the engine to idle for at least 30seconds after starting. Drive at moderatespeeds for a short distance first, espe-cially in cold weather.

STARTING THE ENGINE

4-8

Z X

To apply: Firmly depress the parking brake.

To release:

1. Firmly apply the foot brake.

2. Move the gearshift lever to the P (Park)position.

3. Pull the parking brake release lever.

4. Before driving, be sure the brake warninglight goes out.

WARNING● Be sure the parking brake is fully

released before driving. Failure to doso can cause brake failure and leadto an accident.

● Do not release the parking brakefrom outside the vehicle.

● Do not use the gearshift in place ofthe parking brake. When parking, besure the parking brake is fullyengaged.

● Do not leave children unattended ina vehicle. They could release theparking brake and cause anaccident.

ASD0012

PARKING BRAKEOPERATION

4-9

Z X

The cruise control allows driving at speedsbetween 30 and 90 MPH (48 and 144 km/h)without keeping your foot on the acceleratorpedal.

To turn the cruise control on, push theCRUISE CONT main switch. The indicatorlight on the switch comes on.

To set at cruising speed, accelerate yourvehicle to the desired speed, push theCOAST/SET switch and release it. TheCRUISE light in the instrument clustercomes on. Take your foot off the acceleratorpedal. Your vehicle maintains the setspeed.

● To pass another vehicle, depress theaccelerator pedal. When you release thepedal, the vehicle returns to the previ-ously set speed.

● The vehicle may not maintain the setspeed when going up or down steep hills.If this happens, drive without the cruisecontrol.

To cancel the preset speed, follow any ofthese three methods:

a) Push the CANCEL button; the CRUISElight goes out.

b) Tap the brake pedal; the CRUISE lightgoes out.

c) Push the cruise control OFF switch. Boththe ON indicator and CRUISE lights go out.

● If you depress the brake pedal whilepushing the RES/ACCEL switch, theRES/ ACCEL function is cancelled.

In order for the RES/ACCEL switch tooperate, the COAST/SET must be usedto re-engage the system.

● The cruise control automatically cancelsif the vehicle slows down more than 8MPH (13 km/h) below the set speed.

ASD0562

CRUISE CONTROL

4-10

Z X

● Move the selector lever to N (Neutral).The CRUISE light goes out.

To reset at a faster cruising speed, useone of the following three methods:

a) Depress the accelerator pedal. When thevehicle attains the desired speed, pushand release the COAST/SET switch.

b) Push and hold the RES/ACCEL switch.When the vehicle attains the speed youdesire, release the switch.

c) Push, then quickly release theRES/ACCEL switch. Each time you dothis, the set speed increases by about 1MPH (1.6 km/h).

To reset at a slower cruising speed, useone of the following three methods:

a) Lightly tap the brake pedal. When thevehicle attains the desired speed, pushthe COAST/SET switch and release it.

b) Push and hold the COAST/SET switch.Release the switch when the vehicleslows down to the desired speed.

c) Push, then quickly release theCOAST/SET switch. Each time you do

this, the set speed decreases by about 1MPH (1.6 km/h).

To resume the preset speed, push andrelease the RES/ACCEL switch. The ve-hicle resumes the last set cruising speedwhen the vehicle speed is over 30 MPH (48km/h).

Precautions● If the cruise control system malfunctions,

it cancels automatically. The CRUISEindicator in the instrument cluster thenblinks to warn the driver.

● When the cruise indicator blinks, turn thecruise control switch (main switch) OFFand have the system checked by yourNISSAN dealer.

● The cruise indicator may blink when thecruise control main switch is turned ONwhile pushing either the RES/ACCEL,COAST/SET, or the CANCEL switch (lo-cated on the steering wheel). To properlyset the cruise control system, perform thesteps above in the order indicated.

WARNINGDo not use the cruise control whendriving under the following conditions:

● it is not possible to keep the vehicleat a set speed.

● in heavy traffic or in traffic that var-ies in speed.

● on winding or hilly roads.

● on slippery roads (rain, snow, ice,etc.).

● in very windy areas.

Doing so could cause a loss of vehiclecontrol and result in an accident.

4-11

Z X

During the first 1,000 miles (1,600 km),follow these recommendations for the futurereliability and fuel economy of your newvehicle. Failure to follow these recommen-dations may result in vehicle damage orshortened engine life.

● Do not drive over 55 MPH (90 km/h) anddo not run the engine over 4,000 RPM.Avoid driving for long periods at constantspeed, either fast or slow.

● Do not accelerate at full throttle in anygear.

● Avoid quick starts.

● Avoid hard braking as much as possible.

● Do not tow a trailer for the first 500 miles(800 km).

● Accelerate slowly and smoothly. Main-tain cruising speeds with a constant ac-celerator position.

● Drive at moderate speeds on the high-way. Driving at high speed lowers fueleconomy.

● Avoid unnecessary stopping and brak-ing. Maintain a safe distance behindother vehicles.

● Use a proper gear range which suits roadconditions. On level roads, shift into highgear as soon as possible.

● Avoid unnecessary engine idling.

● Keep your engine tuned up.

● Follow the recommended periodic main-tenance schedule.

● Keep the tires inflated at the correctpressure. Low pressure increases tirewear and wastes fuel.

● Keep the front wheels in correct align-ment. Improper alignment causes notonly tire wear but also lower fueleconomy.

● Air conditioner operation lowers fueleconomy. Use the air conditioner onlywhen necessary.

● When cruising at highway speeds, it ismore economical to use the air condi-tioner and leave the windows closed toreduce drag.

SD1001M

BREAK-IN SCHEDULE INCREASING FUELECONOMY

4-12

Z X

WARNINGDo not park the vehicle over flammablematerials such as dry grass, waste pa-per or rags. They may ignite and causea fire.

1. Firmly apply the parking brake.

2. Move the gearshift lever to the P (Park)position.

WARNING

Safe parking procedures require thatboth the parking brake be set and thetransmission placed into P (Park)position. Failure to do so could causethe vehicle to move unexpectedly orroll away and result in an accident.Make sure the shift lever has beenpushed up as far as it can go andcannot be moved without pulling it to-wards you.

3. To help prevent the vehicle from rolling

into the street when parked on a slopingdriveway, it is a good practice to turn thewheels as illustrated.

● HEADED DOWNHILL WITH CURB: s1

Turn the wheels into the curb and movethe vehicle forward until the curb sidewheel gently touches the curb.

● HEADED UPHILL WITH CURB: s2

Turn the wheels away from the curb andmove the vehicle back until the curb sidewheel gently touches the curb.

● HEADED UPHILL OR DOWNHILL, NOCURB: s3

Turn the wheels toward the side of theroad so the vehicle will move away fromthe center of the road if it moves.

4. Turn the ignition key to the LOCK posi-tion and remove the key.

WARNING● Never leave the engine running while

the vehicle is unattended.

● Never leave children unattended inthe vehicle.

ASD0007

PARKING/PARKING ON HILLS

4-13

Z X

The power assisted steering is designed touse a hydraulic pump, driven by the engine,to aid steering.

If the engine stops or the drive belt breaks,you still have control of the vehicle. How-ever, much greater steering effort isneeded, especially in sharp turns or at lowspeeds.

The brake system has two separate hydrau-lic circuits. If one circuit develops a problemyou will still have braking at two wheels.

Vacuum assisted brake

The brake booster aids braking by usingengine vacuum. If the engine stops, you canstop the vehicle by depressing the brakepedal. However, greater foot pressure onthe brake pedal is required to stop thevehicle, and the stopping distance is longer.

Wet brakes

When the vehicle is washed or driventhrough water, the brakes may get wet. As aresult, your braking distance is longer andthe vehicle may pull to one side duringbraking.

To dry brakes, drive the vehicle at a safespeed while lightly pressing the brake pedalto heat up the brakes. Do this until thebrakes return to normal. Avoid driving thevehicle at high speeds until the brakesfunction correctly.

Using the brakes

Avoid resting your foot on the brake pedalwhile driving. This overheats the brakes,wears out the brake linings and pads faster

and reduces gas mileage.

To help save the brakes and to prevent thebrakes from overheating, reduce speed anddownshift to a lower gear before going downa slope or long grade. Overheated brakesmay reduce braking performance and couldresult in loss of vehicle control.

WARNINGWhile driving on a slippery surface, becareful when braking, accelerating ordownshifting. Abrupt braking actionsor sudden acceleration could cause thewheels to skid and result in an acci-dent.

POWER STEERING SYSTEM BRAKE SYSTEM

4-14

Z X

The anti-lock brake system controls thebrakes at each wheel so the wheels do notlock when braking abruptly or when brakingon slippery surfaces. The system detects therotation speed at each wheel and varies thebrake fluid pressure to prevent each wheelfrom locking and sliding. By preventing wheellockup, the system helps the driver maintainsteering control and helps to minimize swerv-ing and spinning on slippery surfaces.

Using the system

Depress the brake pedal and hold it down.

WARNINGDo not pump the brake pedal. Doing somay result in increased stopping dis-tances.

Normal operationThe anti-lock brake system does not operateat speeds below 3 to 6 MPH (5 to 10 km/h) tocompletely stop the vehicle. (The speeds varyaccording to road conditions.) When the anti-lock system senses one or more wheels areclose to locking up, the actuator (under thehood) rapidly applies and releases hydraulicpressure (like pumping the brakes very

quickly). While the actuator is working, youmay feel a pulsation in the brake pedal andhear a noise or vibration from the actuatorunder the hood. This is normal and indicatesthe anti-lock system is working properly. How-ever, the pulsation may indicate road condi-tions are hazardous and extra care is requiredwhile driving.

Self-test featureThe anti-lock brake system consists of elec-tronic sensors, electric pumps, and hydraulicsolenoids controlled by a computer. The com-puter has a built-in diagnostic feature thattests the system each time you start theengine and move the vehicle at a low speed inforward or reverse. When the self-test occurs,you may hear a ‘‘clunk’’ noise and/or feel apulsation in the brake pedal. This is normaland is not an indication of any malfunction. Ifthe computer senses any malfunction, itswitches the anti-lock brake system OFF andturns on the ABS brake warning light in thedashboard. The brake system then operatesnormally, but without anti-lock assistance.

If the light comes on during the self-test, orwhile driving, take your vehicle to your NIS-SAN dealer for repair at your earliest conve-nience.

WARNINGThe anti-lock brake system is a sophis-ticated device, but it cannot preventaccidents resulting from careless ordangerous driving techniques. It canhelp maintain vehicle control duringbraking on slippery surfaces, but re-member that the stopping distance onslippery surfaces will be longer than onnormal surfaces, even with the anti-lock system. Stopping distances mayalso be longer on rough, gravel orsnow covered roads, or if you are usingtire chains. Always maintain a safe dis-tance from the vehicle in front of you.Ultimately, the responsibility for safetyof self and others rests in the hands ofthe driver.

Tire type and condition of tires mayalso affect braking effectiveness.

● When replacing tires, install thespecified size of tires on all 4 wheels.

ANTI-LOCK BRAKE SYSTEM(ABS) (if so equipped)

4-15

Z X

● When installing a spare tire, makesure it is the proper size and type asspecified on the tire placard. For tireplacard location information, refer to‘‘Tire placard’’ in the Owner’sManual index.

● Refer to ‘‘Wheels and tires’’ in the‘‘Do-it-yourself operations’’ sectionof this manual.

Freeing a frozen door lock

To prevent a door lock from freezing, applyde-icer or glycerin to it through the key hole.If the lock becomes frozen, heat the keybefore inserting it into the key hole.

Anti-freeze

In the winter, when it is anticipated that thetemperature will drop below 32°F (0°C),check the anti-freeze (ethylene glycol base)to assure proper winter protection. For de-tails, see ‘‘Engine cooling system’’ in the‘‘Do-it-yourself operations’’ section.

BatteryIf the battery is not fully charged duringextremely cold weather conditions, the bat-tery fluid may freeze and damage the bat-tery. To maintain maximum efficiency, thebattery should be checked regularly. Fordetails, see ‘‘Battery’’ in the ‘‘Do-it-yourselfoperations’’ section.

Draining of coolant waterIf the vehicle is to be left outside withoutanti-freeze, drain the cooling system byopening the drain valves located under theradiator and on the engine block. Refill

before operating the vehicle. See ‘‘Chang-ing engine coolant’’ in the ‘‘Do-it-yourselfoperations’’ section.

Tire equipment1. SUMMER tires are of a tread design to

provide superior performance on drypavement. However, the performance ofthese tires is substantially reduced insnowy and icy conditions. If you operateyour vehicle on snowy or icy roads, NIS-SAN recommends using MUD & SNOWor ALL SEASON tires on all four wheels.Please consult your NISSAN dealer forthe tire type, size, speed rating and avail-ability information.

2. For additional traction on icy roads, stud-ded tires may be used. However, someprovinces and states prohibit their use.Check local, state and provincial lawsbefore installing studded tires.

Skid and traction capabilities of studdedsnow tires, on wet or dry surfaces, maybe poorer than that of non-studded snowtires.

3. Tire chains may be used if desired. Makesure they are of proper size for the tireson your vehicle and are installed accord-

COLD WEATHER DRIVING

4-16

Z X

ing to the chain manufacturer’s sugges-tions. In addition, drive at a reducedspeed, otherwise, your vehicle may bedamaged and/or vehicle handling andperformance may be adversely affected.

Tire chainsUse of tire chains may be prohibited accord-ing to location. Check the local laws beforeinstalling tire chains. When installing tirechains, make sure they are of proper sizefor the tires on your vehicle and are installedaccording to the chain manufacturer’s sug-gestions. Use only SAE Class ‘‘S’’ chains.Other types may damage your vehicle. Usechain tensioners when recommended bythe tire chain manufacturer to ensure a tightfit. Loose end links of the tire chain must besecured or removed to prevent the possibil-ity of whipping action damage to the fendersor undercarriage. If possible, avoid fullyloading your vehicle when using tire chains.In addition, drive at a reduced speed. Do notexceed maximum speed suggested bychain manufacturer. Otherwise, your ve-hicle may be damaged and/or vehicle han-dling and performance may be adverselyaffected.

Never install tire chains on T-type and smallsize spare tires. Do not use tire chains ondry roads.

Special winter equipment

It is recommended that the following itemsbe carried in the vehicle during winter:

1. A scraper and stiff-bristled brush to re-move ice and snow from the windowsand wiper blades.

2. A sturdy, flat board to be placed underthe jack to give it firm support.

3. A shovel to dig the vehicle out of snow-drifts.

4. Extra window washer fluid to refill thereservoir tank.

Driving on snow or ice

WARNING● Wet ice (32°F, 0°C and freezing rain),

very cold snow or ice can be slickand very hard to drive on. The ve-hicle will have a lot less traction or‘‘grip’’ under these conditions. Try toavoid driving on wet ice until theroad is salted or sanded.

● Whatever the condition, drive withcaution. Accelerate and slow downwith care. If accelerating or down-shifting too fast, the drive wheelswill lose even more traction.

● Allow more stopping distance underthese conditions. Braking should bestarted sooner than on drypavement.

● Allow greater following distances onslippery roads.

● Watch for slippery spots (glare ice).These may appear on an otherwiseclear road in shaded areas. If a patchof ice is seen ahead, brake beforereaching it. Try not to brake whileactually on the ice, and avoid anysudden steering maneuvers.

● Do not use the cruise control onslippery roads.

● Snow can trap dangerous exhaustgases under your vehicle. Keepsnow clear of the exhaust pipe andfrom around your vehicle.

4-17

Z X

Engine block heater/Engine heater(if so equipped)

An engine block heater/engine heater toassist extreme cold temperature starting isavailable through your NISSAN dealer.

WARNING

Do not use your heater with an un-grounded electrical system or two-pronged (cheater) adapters. You can beinjured by an electrical shock if you usean ungrounded connection.

4-18

Z X

5 In case of emergency

Flat tire ...................................................................5-2Jump starting..........................................................5-8Push starting ........................................................5-10If your vehicle overheats ......................................5-10

After an accident ..................................................5-11Tow truck towing ..................................................5-12Vehicle recovery (freeing a stuck vehicle) ...........5-14

Z X

If you have a flat tire, follow the instructionsbelow:

Stopping the vehicle1. Safely move the vehicle off the road and

away from traffic.

2. Turn on the hazard warning flashers.

3. Park on a level surface and apply theparking brake. Move the gearshift leverto the P (Park) position.

4. Turn off the engine.

5. Raise the hood to warn other traffic, andto signal professional road assistancepersonnel that you need assistance.

6. Have all passengers get out of the vehicleand stand in a safe place, away from trafficand clear of the vehicle.

WARNING● Make sure the parking brake is se-

curely applied and the automatictransmission is shifted into P.

● Never change tires when the vehicleis on a slope, ice or slippery areas.This is hazardous.

● Never change tires if oncoming traf-fic is close to your vehicle. Wait forprofessional road assistance.

Getting the tools and spare tireRemove the jack and the tool kit from thejack storage compartment in the luggagearea. Remove the lug wrench from the toolkit.

ACE0015

FLAT TIRE

5-2

Z X

1. Remove the plastic hex nut cover in thecarpeting of the cargo area. The hex nutis used to lower and raise the spare tirelocated underneath the vehicle.

2. Place the lug wrench over the hex nutand turn counterclockwise until the cableextends completely. The spare tire hexnut rachets when the cable is fully ex-tended.

3. Carefully slide the tire from under therear of the vehicle.

4. Stand the tire up to easily remove theretainer.

ACE0001 ACE0006 ACE0014

5-3

Z X

Blocking wheelsPlace suitable blocks at both the front andback of the wheel diagonally opposite theflat tire. This prevents the vehicle from roll-ing when it is jacked up.

WARNINGBe sure to block the wheel as the ve-hicle may move and result in personalinjury.

Removing wheel coverRemove the jack rod from the tool kit. Forwheel cover removal, place the screwdrivertip of the jack rod between the wheel coverand the edge of the rim. Push and twistgently.

Removing wheel capFor cap removal, place the screwdriver tipof the jack rod into the indentation betweenthe cap and the wheel. Push and twistgently.

CAUTIONDo not use your hands to pry off wheelcaps or wheel covers. Doing so couldresult in personal injury.

CE1003M ACE0561 ACE0563

5-4

Z X

Jacking up and removing tireCarefully read the caution label attachedto the jack body and the following in-structions.1. Place the jack directly under the jack-up

point as illustrated above so the top ofthe jack contacts the vehicle at thejack-up point. Align the center of both thejack head and the notch at the jack-uppoint as shown. Also fit the notchedportion of the vehicle in the groove of thejack head as shown.

The jack should be used on level, firmground.

2. Loosen each wheel nut one or two turnsby turning counterclockwise with the lugwrench. Do not remove the wheel nutsuntil the tire is off the ground.

3. Carefully raise the vehicle until the tireclears the ground. To lift the vehicle,securely hold the jack lever and rod withboth hands as shown above. Removethe wheel nuts, and then remove the tire.

WARNING● Never get under the vehicle while it

is supported only by the jack.

● Use the jack provided with your ve-hicle. Do not use the jack providedwith your vehicle on other vehicles.The jack is designed only for liftingyour vehicle during a tire change.

● Use the correct jack-up points; neveruse any other part of the vehicle forjack support.

ACE0009 CE1063M

5-5

Z X

● Never jack up the vehicle more thannecessary.

● Never use blocks on or under thejack.

● Do not start or run engine whilevehicle is on the jack as it may causethe vehicle to move.

● Do not allow passengers to stay inthe vehicle while it is on the jack.

● Never run the engine with the wheelsoff of the ground. It may cause thevehicle to move.

Installing wheelThe T-type spare tire is designed foremergency use. See specific instruc-tions under the heading ‘‘Wheels andtires’’ in the ‘‘Do-it-yourself operations’’section.

1. Clean any mud or dirt from the surfacebetween the wheel and hub.

2. Carefully put the wheel on and tightenthe lug nuts finger tight.

3. With the lug wrench, tighten the lug nutsalternately and evenly until they are tight.

4. Lower the vehicle slowly until the tiretouches the ground. Then, with the lugwrench, tighten the lug nuts securely inthe sequence as illustrated.

WARNING

● Incorrect wheel nuts or improperlytightened wheel nuts can cause thewheel to become loose or come off.This could cause an accident.

● Do nut use oil or grease on the wheelstuds or nuts. This could cause thenuts to become loose.

As soon as possible, tighten the lug nutsto the specified torque with a torquewrench.

Lug nut tightening torque:72 to 87 ft-lb (98 to 118 N zm)

Adjust tire pressure to the COLD pres-sure.

COLD pressure:

After the vehicle has been parked forthree hours or more or driven less than 1mile (1.6 km).

COLD tire pressures are shown on the

CE1003

5-6

Z X

tire placard affixed to the driver sidecenter pillar.

● Retighten the lug nuts when the ve-hicle has been run for 600 miles (1,000km) after installing the aluminumwheel.

5. Securely store the jacking equipment inthe vehicle. The tool kit is stored behindthe jack.

Stowing the spare tire or flat tire1. To raise the tire to the stowed position,

install the retainer through the wheelcenter and turn the wheel lug wrenchclockwise until the tire is raised to itsoriginal position underneath the vehicle.

The spare tire hex nut ratchets whenthe tire is raised. It won’t allow you toover-tighten.

2. Check for proper seating against under-

body supports. If necessary, loosen tire,reposition and retighten.

WARNING● Always make sure that the spare tire

and jacking equipment are properlysecured after use. Such items canbecome dangerous projectiles in anaccident or sudden stop.

● The T-type spare tire is designed foremergency use. See specific instruc-tions under the heading ‘‘Wheelsand tires’’ in the ‘‘Do-it-yourself op-erations’’ section.ACE0016

5-7

Z X

To start your engine with a booster battery,the instructions and precautions below mustbe followed.

WARNING● If done incorrectly, jump starting can

lead to a battery explosion, resultingin severe injury or death. It couldalso damage your vehicle.

● Explosive hydrogen gas is alwayspresent in the vicinity of the battery.Keep all sparks and flames awayfrom the battery.

● Do not allow battery fluid to comeinto contact with eyes, skin, cloth orpainted surfaces. Battery fluid is acorrosive sulfuric acid solutionwhich can cause severe burns. If thefluid should come into contact withanything, immediately flush the con-tacted area with water.

● Keep battery out of the reach ofchildren.

● The booster battery must be rated at12 volts. Use of an improper ratedbattery can damage your vehicle.

● Whenever working on or near a bat-tery, always wear suitable eye pro-tectors (for example, goggles or in-dustrial safety spectacles) andremove rings, metal bands, or anyother jewelry. Do not lean over whenjump starting.

● Do not attempt to jump start a frozenbattery. It could explode and causeserious injury.

● Your vehicle has an automatic en-gine cooling fan. It could come on atany time. Keep hands and other ob-jects away from it.

JUMP STARTING

5-8

Z X

Always follow the instructions below.Failure to do so could result in damageto the charging system and cause per-sonal injury.

1. If the booster battery is in another ve-hicle, position the two vehicles to bringtheir batteries close to each other.

Do not allow the two vehicles to touch.

2. Apply the parking brake. Move the gear-shift lever to the P (Park) position. Switchoff all unnecessary electrical systems(lights, heater, air conditioner, etc.).

3. Remove vent caps on the battery (if soequipped). Cover the battery with an oldcloth to reduce explosion hazard.

4. Connect jumper cables in the sequenceas illustrated.

CAUTION● Always connect positive (+) to posi-

tive (+) and negative (−) to bodyground (for example, the strutmounting bolt, etc. — not to thebattery).

● Make sure that cables do not touchmoving parts in the engine compart-ment and that clamps do not contactany other metal.

5. Start the engine of the other vehicle andlet it run for a few minutes.

6. Keep the engine speed of the other ve-hicle at about 2,000 RPM, and start yourengine in the normal manner.

CAUTIONDo not keep the starter motor engagedfor more than 10 seconds. If the enginedoes not start right away, turn the keyoff and wait 3 to 4 seconds beforetrying again.

7. After starting your engine, carefully dis-connect the negative cable and then thepositive cable.

8. Replace the vent caps (if so equipped).Be sure to dispose of the cloth used tocover the vent holes as it may be con-taminated with corrosive acid.

CE1071M

5-9

Z X

CAUTION● Automatic transmission models can-

not be push started. This may causetransmission damage.

● Three way catalyst equipped modelsshould not be started by pushingsince the three way catalyst may bedamaged.

● Never try to start the vehicle by tow-ing it, when the engine starts, theforward surge could cause the ve-hicle to collide with the tow vehicle.

If your vehicle is overheating (indicated byan extremely high temperature gauge read-ing), or if you feel a lack of engine power,detect abnormal noise, etc., take the follow-ing steps:

WARNING● Do not continue to drive if your ve-

hicle overheats. Doing so couldcause a vehicle fire.

● To avoid the danger of beingscalded, never remove the radiatorcap while the engine is still hot.When the radiator cap is removed,pressurized hot water will spurt out,possibly causing serious injury.

● Do not open the hood if steam iscoming out.

1. Move the vehicle safely off the road,apply the parking brake and move thegearshift lever to the P (Park) position.

Do not stop the engine.

2. Turn off the air conditioner switch. Openall the windows, move the temperaturecontrol dial to warm and fan control knobto 4.

3. If engine overheating is caused by climb-ing a long hill on a hot day, run the engineat a fast idle (approximately 1,500 RPM)until the temperature gauge indicationreturns to normal.

4. Get out of the vehicle. Look and listen forsteam or coolant escaping from the ra-diator before opening the hood. Wait untilno steam or coolant can be seen beforeproceeding.

5. Open the hood.

WARNINGIf steam or water is coming from theengine, stand clear to prevent gettingburned.

6. Visually check drive belts for damage orlooseness. Also check to make sure thecooling fan is running. The radiator hosesand radiator should not leak water. Ifcoolant is leaking, the water pump belt ismissing or loose, or the cooling fan doesnot run, stop the engine.

PUSH STARTING IF YOUR VEHICLEOVERHEATS

5-10

Z X

WARNING● Be careful not to allow your hands,

hair or clothing to come into contactwith, or to get caught in, the runningfan, belts, or motor fan.

● The fan motor may start at any timewhen the coolant temperature is high.

7. After the engine cools down completely,check the coolant level in the reservoirtank with the engine running. Add coolantto the reservoir tank, if necessary. Haveyour vehicle repaired at the nearestNISSAN dealer. Inertia fuel shut-off switch

When the vehicle is involved in a collision,the inertia fuel shutoff switch is designed toautomatically stop the flow of fuel to theengine. The impact forces needed to triggerthe switch do not have to be great. Parkinglot bumping or road impacts (such as drivingover potholes) may trigger the switch.

Once the inertia fuel shutoff switch is trig-gered, it must be reset before the enginecan be started. If your engine cranks butdoes not start after a collision, take thefollowing steps to correctly reset the switch:

1. Turn the key in the ignition to OFF.2. Check under the vehicle for leaking fuel.3. If you do not see or smell fuel, push down

the red reset button on the fuel pumpshut-off switch.

4. Turn the ignition key ON for a few sec-onds, then turn it OFF.

5. Check under the vehicle again for leakingfuel. If you see or smell fuel, do not startyour vehicle again. If no fuel is detected,try to start your vehicle again.

WARNINGIf you see or smell fuel, do not reset theswitch or try to start your vehicle. Youcould injure yourself or others. Have allthe passengers get out of the vehicleand call the local fire department or atowing service.

ACE0018

AFTER AN ACCIDENT

5-11

Z X

When towing your vehicle, all state (provin-cial in Canada) and local regulations fortowing must be followed. Incorrect towingequipment could damage your vehicle.Towing instructions are available from yourNISSAN dealer. Local service operators aregenerally familiar with the applicable lawsand procedures for towing. To assureproper towing and to prevent accidentaldamage to your vehicle, NISSAN recom-mends that you have a service operator towyour vehicle. It is advisable to have theservice operator carefully read the followingprecautions.

WARNING● Never ride in a vehicle that is being

towed.

● Never get under your vehicle after ithas been lifted by a tow truck.

CAUTION● When towing, make sure that the

transmission, axles, steering systemand powertrain are in working con-dition. If any unit is damaged, dolliesmust be used.

● Never use a tow bar that attaches tothe bumper when you tow your ve-hicle. It may damage the bumper andcause damage to the transmission.

● When towing with the front wheelson dollies:Turn the ignition key to the OFFposition and secure the steeringwheel in a straight-ahead positionwith a rope or similar device. Neverplace the ignition key in the LOCKposition. This will result in damageto the steering lock mechanism.Move the gearshift lever to the N(Neutral) position.

● When towing with the rear wheels onthe ground, release the parkingbrake.

● Attach safety chains for all towing.

TOW TRUCK TOWING

5-12

Z X

NISSAN recommends that your vehicle betowed with the driving (front) wheels off theground as illustrated.

● Speed: Below 60 MPH (97 km/h)

● Distance: Less than 500 miles (800 km)

ACE0560

5-13

Z X

CAUTION

Never tow the vehicle with the rearwheels raised (with the front wheels onthe ground) as this may cause seriousand expensive damage to the transmis-sion. If it is necessary to tow the vehiclewith the rear wheels raised, always usetowing dollies under the front wheels.

● If you have to tow the vehicle withfour wheels on ground, observe thefollowing restricted towing speedsand distances:● Speed: Below 30 MPH (50 km/h)● Distance: Less than 40 miles

(65 km)

● Never tow the vehicle from the rear(i.e., backward) with four wheels onthe ground as this may cause seri-ous and expensive damage to thetransmission.

● Do not tow with a sling type truck,either from the front or the rear. Itmay cause body damage.

● Never utilize the rear tie down brack-ets or slots to tow another vehicle asthis may cause body damage.

VEHICLE RECOVERY (freeing astuck vehicle)● Tow chains or cables must only be at-

tached to the main structual members ofthe vehicle.

● Pulling devices should be routed so theydo not touch any part of the suspension,steering, brake or cooling systems.

● Always pull the cable straight out fromthe front or rear of the vehicle. Never pullon the vehicle at an angle.

● Pulling devices such as ropes or canvasstraps are not recommended for use invehicle towing or recovery.

● Stand clear of a stuck vehicle.

WARNINGDo not spin your tires at high speed.This could cause them to explode andresult in serious injury. Parts of yourvehicle could also overheat and bedamaged.

5-14

Z X

6 Appearance and interior care

Cleaning exterior and interior.................................6-2 Corrosion protection...............................................6-4

Z X

In order to maintain the appearance of yourvehicle, it is important to take proper care ofit.

In the following cases, please wash yourvehicle as soon as possible to protect thepaint surface:

● after a rainfall to prevent possible dam-age from acid rain.

● after driving on coastal roads.

● when contaminants such as soot, birddroppings, tree sap, metal particles orbugs get on the paint surface.

● when dust or mud builds up on the surface.

Whenever possible, store or park your ve-hicle inside a garage or in a covered area.

When it is necessary to park outside, park ina shady area or protect the vehicle with abody cover.

Be careful not to scratch the paint sur-face when putting on or removing a bodycover.

WashingWash dirt off with a wet sponge and plentyof water. Clean the vehicle thoroughly usinga mild soap, a special vehicle soap orgeneral purpose dish-washing liquid mixedwith clean, lukewarm (never hot) water.

CAUTION● Do not use strong household soap,

strong chemical detergents, gaso-line or solvents.

● Do not wash the vehicle in directsunlight or while the vehicle body ishot, as the surface may becomewaterspotted.

● Avoid using tight-napped or roughcloths such as washing mitts. Caremust be taken when removingcaked-on dirt or other foreign sub-stances so the paint surface is notscratched or damaged.

Rinse the vehicle thoroughly with plenty ofclean water.

Inside flanges, seams and folds on thedoors, hatches and hood are particularlyvulnerable to the effects of road salt. There-fore, these areas must be regularly cleaned.Take care that the drain holes in the loweredge of the door are open. Spray waterunder the body and in the wheel wells toloosen the dirt and wash away road salt.

A damp chamois can be used to dry thevehicle to avoid water spots.

WaxingRegular waxing protects the paint surfaceand helps retain new vehicle appearance.After waxing, polishing is recommended toremove built-up residue and to avoid a‘‘weathered’’ appearance.

Your NISSAN dealer can assist you in

AI1002M

CLEANING EXTERIOR ANDINTERIOR

6-2

Z X

choosing the proper product.

● Wax your vehicle only after a thoroughwashing. Follow the instructions suppliedwith the wax.

● Do not use a wax containing any abra-sives, cutting compounds or cleanersthat may damage the vehicle finish.

● If the surface does not polish easily, usea ‘‘road tar’’ remover and wax again.

Machine compounding or aggressive pol-ishing on a base coat/clear coat paint finishmay dull the finish or leave swirl marks.

Removing spotsRemove tar and oil spots, industrial dust,insects, and tree sap as quickly as possiblefrom the surface of the paint to avoid lastingdamage or staining. Special cleaning prod-ucts are available at your NISSAN dealer orany automotive accessory store.

UnderbodyIn areas where road salt is used in winter,the underbody must be cleaned regularly.This prevents dirt and salt from building upand causing underbody and suspensioncorrosion. Before the winter period and

again in the spring, the underseal must bechecked and, if necessary, re-treated.

Cleaning glass

Use glass cleaner to remove smoke anddust film from the glass surfaces. It is nor-mal for glass to become coated with a filmafter the vehicle is parked in the hot sun.Glass cleaner and a soft cloth easily removethis film.

CAUTION

When cleaning the inside of the win-dow, do not use sharp-edged tools,abrasive cleaners or chlorine-baseddisinfectant cleaners. They could dam-age the rear window defogger.

Cleaning aluminum alloy wheels

Wash regularly, especially during wintermonths in areas where road salt is used.Salt could discolor the wheel if not removed.

Chrome partsClean all chrome parts regularly with anon-abrasive chrome polish to maintain thefinish.

Cleaning interior

Occasionally remove loose dust from theinterior trim, plastic parts and seats using avacuum cleaner or soft brush. Wipe thevinyl and leather surfaces with a clean, softcloth dampened in mild soap solution, thenwipe clean with a dry, soft cloth. Beforeusing any fabric protector, read the manu-facturer’s recommendations. Some fabricprotectors contain chemicals that may stainor bleach the seat material.

CAUTION

● Never use benzine, thinner, or anysimilar material.

● Leather seats should be regularlycoated with a leather wax like saddlesoap. Never use car wax.

● Never use fabric protectors unlessrecommended by the manufacturer.

Front floor mat positioning aidThis model includes a front floor matbracket to act as a floor mat positioning aid.NISSAN floor mats, specially designed foryour vehicle, incorporate grommets. To in-

6-3

Z X

stall, simply position the mat using the floormat bracket hook through the floor matgrommet hole while centering the mat in thefloor pan contour.

Periodically check to make certain the matis properly positioned.

Floor matsThe use of genuine NISSAN floor mats canextend the life of your vehicle carpet andmake it easier to clean the interior. Nomatter what mats are used, be sure theyare fitted for your vehicle and are prop-erly positioned in the footwell to preventinterference with pedal operation. Matsshould be maintained with regular cleaningand replaced if they become excessivelyworn.

Seat beltsThe seat belts can be cleaned by wipingthem with a sponge dampened in a mildsoap solution. Allow the belts to dry com-pletely before using them.

WARNINGDo not allow wet belts to roll up in theretractor. NEVER use bleach, dye, orchemical solvents since these may se-verely weaken the seat belt webbing.

Most common factors contributingto vehicle corrosion:

1. The accumulation of moisture-retainingdirt and debris in body panel sections,cavities, and other areas.

2. Damage to paint and other protectivecoatings caused by gravel and stonechips or minor traffic accidents.

Environmental factors influence therate of corrosion:

Moisture

Accumulation of sand, dirt and water on thevehicle body underside can accelerate cor-rosion. Wet floor coverings do not dry com-pletely inside the vehicle, and should beremoved for drying to avoid floor panelcorrosion.

Relative humidity

Corrosion will be accelerated:

● in areas of high relative humidity.

● especially in those areas where the tem-peratures stay above freezing.

● where atmospheric pollution exists.

CORROSION PROTECTION

6-4

Z X

● where road salt is used.

Temperature

A temperature increase accelerates the rateof corrosion to those parts which are notwell ventilated.

Air pollution

Industrial pollution, the presence of salt inthe air in coastal areas, or heavy road saltuse accelerates the corrosion process.Road salt also accelerates the disintegra-tion of paint surfaces.

To protect your vehicle from corro-sion:● Wash and wax your vehicle often to keep

the vehicle clean.

● Always check for minor damage to thepaint and repair it as soon as possible.

● Keep drain holes at the bottom of thedoors open to avoid water accumulation.

● Check the underbody for accumulation ofsand, dirt or salt. If present, wash withwater as soon as possible.

CAUTION

● NEVER remove dirt, sand or otherdebris from the passenger compart-ment by washing it out with a hose.Remove dirt with a vacuum cleaneror broom.

● Never allow water or other liquids tocome in contact with electronic com-ponents inside the vehicle.

6-5

Z X

Z X

7 Do-it-yourself operations

Maintenance precautions .......................................7-2Engine compartment check locations ....................7-3Engine cooling system ...........................................7-4Checking engine coolant level ...............................7-4Changing engine coolant .......................................7-5Engine oil ...............................................................7-5Checking engine oil level .......................................7-5Changing engine oil ...............................................7-6Changing engine oil filter .......................................7-7Automatic transmission fluid (ATF) ........................7-8Temperature conditions for checking ATF.............7-8Power steering fluid................................................7-9Brake fluid ............................................................7-10Window washer fluid ............................................7-10Battery ..................................................................7-11Jump starting........................................................7-12

Drive belts ............................................................7-12Spark plug replacement .......................................7-12Air cleaner housing filter ......................................7-13Wiper blades ........................................................7-14Parking brake check.............................................7-16Brake pedal ..........................................................7-16Brake booster .......................................................7-17Fuses....................................................................7-17Fusible links..........................................................7-18Light bulbs............................................................7-19Headlights ............................................................7-19Bulb replacement .................................................7-21Wheels and tires ..................................................7-25Types of tires........................................................7-26Tire chains............................................................7-26

Z X

When performing any inspection or mainte-nance work on your vehicle, always takecare to prevent serious accidental injury toyourself or damage to the vehicle. Thefollowing are general precautions whichshould be closely observed.

WARNING

● Park the vehicle on a level surface,apply the parking brake securely andblock the wheels to prevent the ve-hicle from moving. Move the gear-shift lever to N (neutral).

● Be sure the ignition key is OFF whenperforming any replacement orrepair.

● Be sure to turn the ignition key to theOFF or LOCK position. When theignition key is in the ON or ACCposition, the cooling fan may start tooperate suddenly even when the en-gine is not running. To avoid injuryalways disconnect the negative bat-tery cable before working near thefan.

● If you must work with the enginerunning, keep your hands, clothing,hair and tools away from movingfans, belts and any other movingparts.

● It is advisable to remove ties and anyjewelry, such as rings, watches, etc.before working on your vehicle.

● If you must run the engine in anenclosed space such as a garage, besure there is proper ventilation forexhaust gases.

● Never get under the vehicle while itis supported only by a jack. If it isnecessary to work under the vehicle,support it with safety stands.

● Keep smoking materials, flame andsparks away from fuel and thebattery.

● On gasoline engine models with themultiport fuel injection (MFI) system,the fuel filter or fuel lines should beserviced by a NISSAN dealer be-cause the fuel lines are under highpressure even when the engine isoff.

CAUTION● Do not work under the hood while

the engine is hot. Turn off the engineand wait until it cools down.

● Never connect or disconnect eitherthe battery or any transistorizedcomponent connector while the igni-tion is ON.

● Avoid contact with used engine oil.Improperly disposed motor oil and/or other vehicle fluids can hurt theenvironment. Always conform to lo-cal regulations for disposal of ve-hicle fluid.

This ‘‘Do-it-yourself operations’’ sectiongives instructions regarding only thoseitems which are relatively easy for an ownerto perform.

You should be aware that incomplete orimproper servicing may result in operatingdifficulties or excessive emissions, andcould affect your warranty coverage. If indoubt about any servicing, have it doneby your NISSAN dealer.

MAINTENANCEPRECAUTIONS

7-2

Z X

ADI0570

ENGINE COMPARTMENTCHECK LOCATIONS

7-3

Z X

The engine cooling system is filled at thefactory with a high-quality, year-round, anti-freeze coolant solution. The anti-freeze so-lution contains rust and corrosion inhibitors,therefore additional cooling system addi-tives are not necessary.

CAUTIONWhen adding or replacing coolant, besure to use only an ethylene glycolanti-freeze with the proper mixture ratioof 50% anti-freeze and 50% distilledwater. The use of other types of coolantsolutions may damage your cooling sys-tem.

Outside tempera-ture down to Anti-

freezeDistilledwater

°C °F

−35 −30 50% 50%

WARNING● Never remove the radiator cap when

the engine is hot. Wait until the en-gine and radiator cool down. Seriousburns could be caused by high pres-sure fluid escaping from theradiator.

● The radiator is equipped with a pres-sure cap. Use an appropriateNISSAN genuine cap or its equiva-lent when replacement is required.

CHECKING ENGINE COOLANTLEVEL

With coolant reservoirCheck the coolant level in the reservoir tankwhen the engine is cold. If the coolant levelis below MIN, add coolant up to the MAXlevel. If the reservoir tank is empty, checkthe coolant level in the radiator when theengine is cold. If there is insufficient cool-ant in the radiator, fill the radiator withcoolant up to the filler opening and also addit to the reservoir tank up to the MAX level.

ADI0571

ENGINE COOLING SYSTEM

7-4

Z X

If the cooling system frequently requirescoolant, have it checked by your NISSANdealer.

CHANGING ENGINE COOLANTYour NISSAN dealer can change the enginecoolant. The service procedure is found inNISSAN’s service manual.

Improper servicing can result in reducedheater performance and engineoverheating.

WARNING● To avoid danger of being scalded,

never change the coolant when theengine is hot.

● Never remove the radiator cap whenthe engine is hot. Serious burnscould be caused by high pressurefluid escaping from the radiator.

CHECKING ENGINE OIL LEVEL1. Park the vehicle on a level surface and

apply the parking brake.

2. Run the engine until it reaches operatingtemperature.

3. Turn the engine off. Wait a few minutesfor the oil to drain back into the oilpan.

4. Remove the dipstick and wipe it clean.Reinsert it all the way.

5. Remove the dipstick again and check theoil level. It should be between the H andL marks. If the oil level is below the Lmark, remove the oil filler cap and pourrecommended oil through the opening.Do not overfill.

6. Recheck the oil level with the dipstick.

It is normal to add some oil between oilmaintenance intervals or during thebreak-in period, depending on the sever-ity of operating conditions.

ADI0008 ADI0009

ENGINE OIL

7-5

Z X

CAUTION● Oil level should be checked regu-

larly. Operating with an insufficientamount of oil can damage the en-gine, and such damage is not cov-ered by warranty.

CHANGING ENGINE OIL1. Park the vehicle on a level surface and

apply the parking brake.

2. Run the engine until it reaches operatingtemperature, then turn it off.

3. Place a large drain pan under the drainplug.

4. Remove the oil filler cap.

5. Remove the drain plug with a wrench andcompletely drain the oil.

If the oil filter is to be changed, removeand replace it at this time. See ‘‘Chang-ing the oil filter’’ later in this section.

WARNING● Be careful not to burn yourself, as

the engine oil is hot.

● Prolonged and repeated contact withused engine oil may cause skincancer.

● Try to avoid direct skin contact withused oil. If skin contact is made,wash thoroughly with soap or handcleaner as soon as possible.

● Keep used engine oil out of reach ofchildren.

Waste oil must be disposed of properly.Check your local regulations.

6. Clean and re-install the drain plug with anew washer. Securely tighten the drainplug with a wrench.

ADI0057

7-6

Z X

Drain plug tightening torque:22 to 29 ft-lb(29 to 39 N zm)

Do not use excessive force.

7. Refill the engine with a recommended oiland install the cap securely. See the‘‘Technical and consumer information’’section for refill capacity.

8. Start the engine. Check for leakagearound the drain plug. Correct as re-quired.

9. Turn the engine off and wait severalminutes. Check the oil level with thedipstick. Add engine oil if necessary. CHANGING ENGINE OIL FILTER

1. Park the vehicle on a level surface andapply the parking brake.

2. Turn the engine off.

3. Loosen the oil filter with an oil filterwrench. Remove the oil filter by turning itby hand.

CAUTION

Be careful not to burn yourself, as theengine oil may be hot.

4. Wipe the engine oil filter mounting sur-face with a clean rag. Be sure to removeany old rubber gasket remaining on themounting surface of the engine.

5. Coat the rubber gasket on the new filterwith clean engine oil.

6. Screw the oil filter in until a slight resis-tance is felt, then tighten additionallymore than 2/3 turn.

7. Start the engine and check for leakagearound the oil filter. Correct as required.

8. Turn the engine off and wait severalminutes. Check the oil level. Add engineoil if necessary.

ADI0010

7-7

Z X

WARNING● When engine is running, keep

hands, jewelry and clothing awayfrom any moving parts such as cool-ing fan and drive belt.

● Automatic transmission fluid is poi-sonous and should be stored care-fully in marked containers out of thereach of children.

TEMPERATURE CONDITIONSFOR CHECKING ATF

● Check the fluid level using the HOTrange on the dipstick after the followingconditions have been met:

— The engine is warmed up to operatingtemperature.

— The vehicle is driven at least 15 minutes.

— The automatic transmission fluid iswarmed to between 151°F and 171°F(66°C to 77°C).

● The fluid can be checked at fluid tem-

peratures of 70°F to 95°F (21°C to 35°C)using the COLD range on the dipstickafter the engine is warmed up and beforedriving. However, the fluid should bere-checked using the HOT range.

1. Park the vehicle on a level surface andset the parking brake.

2. Start the engine, then move the gearshiftlever through the range of gears, endingin P (Park).

ADI0582ADI0572 ADI0573

AUTOMATIC TRANSMISSIONFLUID (ATF)

7-8

Z X

3. Check the fluid level with the engineidling.

4. Remove the dipstick and wipe it cleanwith lint-free paper.

5. Reinsert the dipstick into the chargingpipe as far as it goes.

6. Remove the dipstick and note the read-ing. If the level is at the low side of eitherrange, add fluid to the charging pipe.

CAUTIONDO NOT OVERFILL.Use ONLY Nissan Matic ‘D’ (Continen-tal U.S. and Alaska) or Genuine NissanAutomatic Transmission Fluid(Canada). Dexron® III/Mercon® orequivalent may also be used. Outsidethe continental United States andAlaska contact a Nissan dealership formore information regarding suitablefluids, including recommendedbrand(s) of Dexron® III/Mercon® orDexron® IIE/Mercon® Automatic Trans-mission Fluid.

NOTE:

If the vehicle has been driven for a long

time at high speeds, or in city traffic inhot weather, or if it is being used to pulla trailer, the accurate fluid level cannotbe read. You should wait until the fluidhas cooled down (about 30 minutes).

Check the fluid level in the reservoir.

The fluid level should be checked by lookingat the MAX and MIN lines at fluid tempera-tures of 32°F to 86°F (0°C to 30°C).

If the fluid is below the MIN line, add auto-matic transmission fluid type F up to theMAX line.

CAUTION● Do not overfill.

● The recommended fluid is type Fautomatic transmission fluid orequivalent.

ADI0017

POWER STEERING FLUID

7-9

Z X

Check the fluid level in the reservoir. If thefluid is below the MIN line or the brakewarning light comes on, add DOT 3 fluid upto the MAX line. If fluid must be addedfrequently, the system should be thoroughlychecked by your NISSAN dealer. For furtherbrake fluid specification information, refer tothe ‘‘Technical and Consumer Information’’section in this manual.

WARNINGUse only new fluid. Old, inferior, orcontaminated fluid may damage thebrake system. The use of improper flu-ids can damage the brake system andaffect the vehicle’s stopping ability.

CAUTIONDo not spill the fluid on painted sur-faces. This will damage the paint. Iffluid is spilled, wash with water.

Add fluid when the low washer fluid warninglight comes on. To check the fluid level, lookdown the fill tube of the washer fluid reser-voir in the engine compartment.To add fluid, remove the reservoir cap andrefill the reservoir.This reservoir serves both the front and rearwasher systems.

CAUTIONDo not substitute engine anti-freezecoolant for window washer solution.This may result in damage to the paint.

ADI0018 ADI0019

BRAKE FLUID WINDOW WASHER FLUID

7-10

Z X

● Keep the battery surface clean and dry.Any corrosion should be washed off witha solution of baking soda and water.

● Make certain the terminal connectionsare clean and securely tightened.

● If the vehicle is not to be used for 30 daysor longer, disconnect the negative (−)battery terminal cable to prevent dis-charge.

WARNING● Do not expose the battery to flames

or electrical sparks. Hydrogen gasgenerated by battery action is explo-sive. Do not allow battery fluid tocontact your skin, eyes, fabrics, orpainted surfaces. After touching abattery or battery cap, do not touchor rub your eyes. Thoroughly washyour hands. If the acid contacts youreyes, skin or clothing, immediatelyflush with water for at least 15 min-utes and seek medical attention

● When working on or near a battery,always wear suitable eye protectionand remove all jewelry.

● Keep the battery out of the reach ofchildren.

Check the fluid level in each cell. It shouldbe between the MAX and MIN lines.

If it is necessary to add fluid, add onlydistilled water to bring the level to the indi-cator in each filler opening. Do not overfill.

1. Remove the cell plugs using a suitabletool.

2. Add distilled water up to the MAX level.

3. Tighten cell plugs.

ADI0037

BATTERY

7-11

Z X

JUMP STARTINGIf jump starting is necessary, see the ‘‘Incase of emergency’’ section. If the enginedoes not start by jump starting, the batterymay have to be replaced. Contact yourNISSAN dealer.

WARNINGBe sure the ignition key is OFF. Theengine could rotate unexpectedly.

1. Visually inspect each belt for signs ofunusual wear, cuts, fraying or looseness.If the belt is loose or in poor condition,have it replaced or adjusted by yourNISSAN dealer.

2. Have the belts checked regularly for con-dition and tension in accordance with themaintenance schedule in this manual.

WARNINGBe sure the engine and ignition switchare off and that the parking brake isengaged securely.

CAUTIONBe sure to use the correct socket toremove the plugs. An incorrect socketcan cause damage.

ADI0060 ADI0061

DRIVE BELTS SPARK PLUG REPLACEMENT

7-12

Z X

1. Disconnect the spark plug cables fromthe spark plugs.

When disconnecting, always hold the boots,not the cables.

2. Remove the spark plugs with a sparkplug socket. The plug socket has a rub-ber seal that holds the spark plug so itdoes not fall when it is pulled out. Makesure each spark plug is snugly fitted intothe plug socket.

3. Check the gap on each new spark plugwith a feeler gauge. (The spark plug gapis shown in the ‘‘Technical and consumer

information’’ section.) Adjust it as re-quired.

4. Fit the new plugs, one at a time, into thespark plug socket and install them. Turneach plug several full turns by hand, thentighten with a spark plug socket to thecorrect torque. Do not overtighten.

Spark plug tightening torque:14 to 22 ft-lb (20 to 29 N zm)

5. Holding the boot, re-connect each hightension cable to its proper spark plug bypushing it on until you feel a snap.

The filter should not be cleaned and reused.Replace it according to the maintenanceintervals shown in the ‘‘Maintenance sched-ule’’ section. When replacing the filter, un-clip the four clamps and remove the filter.Wipe the inside of the air cleaner housingand the cover with a damp cloth whenreplacing filter.

DI1017M ADI0579

AIR CLEANER HOUSINGFILTER

7-13

Z X

WARNINGOperating the engine with the air cleaneroff can cause you or others to be burned.The air cleaner not only cleans the air, itstops flame if the engine backfires. If itisn’t there and the engine backfires, youcould be burned. Don’t drive with it off,and be careful working on the enginewith the air cleaner off.

CLEANINGIf your windshield is not clear after using thewindshield washer or if the wiper bladechatters when running, wax or other mate-rial may be on the blade or windshield.

Clean the outside of the windshield with awasher solution or a mild detergent. Yourwindshield is clean if beads do not formwhen rinsing with clear water.

Clean the blade by wiping it with a clothsoaked in a washer solution or a mild deter-gent. Then, rinse the blade with clear water.If your windshield is still not clear after

cleaning the blades and using the wipers,replace the blades.

REPLACEMENT

1. Lift the wiper arm away from the wind-shield.

2. Push the lock pin, then remove the wiperblade.

3. Insert the new wiper blade to the wiperarm until it clicks into place.

DI1018M

WIPER BLADES

7-14

Z X

CAUTION

● After wiper blade replacement, re-turn the wiper arm to its originalposition.

● Otherwise it may be damaged whenthe engine hood is opened.

● Make sure the wiper blade contactsthe glass, otherwise the arm may bedamaged from wind pressure.

Rear wiper blade replacement1. Lift the wiper arm away from the wind-

shield.

2. Push in the lock pin with a suitable tool,then pull up on the blade.

3. Insert a new wiper blade onto the wiperarm and press down until the blade clicksinto place.

ADI0581

7-15

Z X

From the released position, push the park-ing brake foot lever down. If the number ofclicks is out of the range listed above, seeyour NISSAN dealer.

With the engine running, check the distancebetween the upper surface of the pedal andthe floor. If it is out of the range shownabove, see your NISSAN dealer.

Self-adjusting brakes

Your vehicle is equipped with self-adjustingbrakes.

The front disc-type brakes self-adjust everytime the brake pedal is applied. The reardrum-type brakes also self-adjust everytime the brake pedal is applied. If the brakepedal goes down farther than normal, seeyour NISSAN dealer

WARNINGSee your NISSAN dealer and have itchecked if the brake pedal height doesnot return to normal.

Brake pad wear indicatorsThe disc pads on your vehicle have audiblewear indicators. When a brake pad requiresreplacement, it makes a high pitched scrap-ing or screeching sound when the vehicle isin motion whether or not the brake pedal isdepressed. Have the brakes checked assoon as possible if the wear indicator soundis heard.

Under some driving or climate conditions,occasional brake squeak, squeal or othernoise may be heard. Occasional brakenoise during light to moderate stops is nor-mal and does not affect the function orperformance of the brake system.

The rear drum brakes (if so equipped) donot have audible wear indicators. Shouldyou ever hear an unusually loud noise fromthe rear drum brakes, have them inspectedas soon as possible by your NISSANdealer.

ADI0062 ADI0027

PARKING BRAKE CHECK BRAKE PEDAL

7-16

Z X

Proper brake inspection intervals shouldbe followed. For more information regard-ing brake inspections, see the appropriatemaintenance schedule information in the‘‘Maintenance schedule’’ section of thismanual.

Check the brake booster function as fol-lows:

1. With the engine off, press and releasethe brake pedal several times. Whenbrake pedal movement (distance oftravel) remains the same from one pedalapplication to the next, continue on to thenext step.

2. While depressing the brake pedal, startthe engine. The pedal height should dropa little.

3. With the brake pedal depressed, turn theengine off. Keep the pedal depressed forabout 30 seconds; the pedal heightshould not change.

4. Run the engine for one minute withoutdepressing the brake pedal, then turn itoff. Depress the brake pedal severaltimes. The pedal travel distance will de-crease gradually with each depressionas the vacuum is released from thebooster.

If the brakes do not operate properly, seeyour NISSAN dealer.

Engine compartment(headlight fuses)

CAUTION

Never use a fuse of a higher amperagerating than that specified on the fusebox cover. This could damage the elec-trical system or cause a fire.

If a headlight does not come on, check foran open fuse:

The left headlight (driver’s side) fuse islocated in the right-hand fuse box, found in

ADI0583

BRAKE BOOSTER FUSES

7-17

Z X

the right-front corner of the engine compart-ment.

The right headlight (passenger side) fuse islocated in the left-hand fuse box, near theradiator cap.

1. Turn the headlight switch to the OFFposition.

2. Open the engine hood.

3. Remove the appropriate fuse box cover.

4. Remove the fuse with the fuse pullerattached to the passenger compartmentfuse box cover.

5. If the fuse is open, replace it with a newfuse.

6. If a new fuse opens again, have theelectrical system checked and repairedby your NISSAN dealer.

If the electrical equipment does not operateand fuses are in good condition, check thefusible links. If any of these fusible links aremelted, replace only with genuine NISSANparts.

If the new fusible link melts again, have thesystem checked and repaired by yourNISSAN dealer.

ADI0584

FUSIBLE LINKS

7-18

Z X

Passenger compartmentCAUTION

Never use a fuse of a higher amperagerating than that specified on the fusebox cover. This could damage the elec-trical system or cause a fire.

If the electrical equipment does not operate,check for an open fuse:

1. Remove the key from the ignition.

2. Open the fuse box cover. Refer to thefuse label on the fuse box cover to locate

the fuse in question.

3. Remove the fuse with the fuse puller.

4. If the fuse is open, replace it with a newfuse.

5. If a new fuse opens again, have theelectrical system checked and repairedby your NISSAN dealer.

HEADLIGHTSThe headlight is a semi-sealed beam typewhich uses a replaceable headlight (halo-gen) bulb. A bulb can be replaced frominside the engine compartment without re-moving the headlight assembly.

CAUTION● High pressure halogen gas is sealed

inside the halogen bulb. The bulbmay break if the glass envelope isscratched or the bulb is dropped.

ADI0580 AEL076-A

LIGHT BULBS

7-19

Z X

● When handling the bulb, do nottouch the glass envelope.

Removing the headlight bulb1. Disconnect the negative (-) battery cable.

2. Disconnect the electrical connector fromthe rear end of the bulb.

3. Turn the bulb retaining ring counterclock-wise until it is free from the headlightreflector, then remove it.

4. Remove the headlight bulb by pulling itstraight out. Do not shake or rotate thebulb when removing it.

Replacing the headlight bulb1. Insert the bulb into the headlight reflector

with the flat side of the plastic base facingupward.

2. Install the bulb retaining ring and turn itclockwise until it stops.

3. Push the electrical connector into thebulb plastic base until it snaps and stops.

CAUTION

DO NOT TOUCH THE BULB.

● Use the same number and wattageas originally installed:

Wattage 65/45

Bulb no. 9004

● Aiming is not necessary after replac-ing the bulb. When aiming adjust-ment is necessary, contact yourNISSAN dealer.

● Do not leave the bulb out of theheadlight reflector for a long periodof time as dust, moisture and smokemay enter the headlight body andaffect the performance of the head-light.

7-20

Z X

BULB REPLACEMENT

Item Wattage (W) Bulb No.

Headlight (semi-sealed beam)

High/Low 65/45 9004

Front combination light:

Front side marker light 3.8 194

Parking/Cornering 8.25/27 3157

Front turn signal light 27 3475

Rear combination light:

Turn signal 27 1156NA

Stop/Tail 27 1157

Back-up light 27 3156

Rear side marker light 3.8 194

License plate light 3.8 194

High-mounted stop light 12.8 912

Interior lights 12 211-2

Personal reading light 9.8 208

Luggage compartment light 12 211-2

Steplight 3.8 194

Spotlight 10 —

7-21

Z X

Replacement proceduresAll lights (except for headlights) are eithertype A, B, C or D. When replacing a bulb,first remove the lens and/or cover.

ADI0577

ADI0044

7-22

Z X

ADI0049

7-23

Z X

ADI0574

7-24

Z X

If you have a flat tire, see the ‘‘In case ofemergency’’ section.

Maximum inflation pressure

Do not exceed the maximum inflation pres-sure shown on the side wall of the tire.

Tire inflation pressure

Periodically check the tire pressure (includ-ing spare). Incorrect tire pressure may ad-versely affect tire life and vehicle handling.Tire pressure should be checked when tiresare COLD. Tires are considered COLD afterthe vehicle has been parked for three orADI0578

DI1033M

WHEELS AND TIRES

7-25

Z X

more hours, or driven less than 1 mile (1.6km). COLD tire pressures are shown on thetire placard affixed to the glove box door.

WARNING

● The vehicle capacity weight is indi-cated on the tire placard. Do not loadyour vehicle beyond this capacity.Overloading your vehicle may result inreduced tire life, unsafe operating con-ditions due to premature tire failure, orunfavorable handling characteristicsand could also lead to a serious acci-dent. Loading beyond the specified ca-pacity may also result in failure ofother vehicle components.

● Before taking a long trip, or wheneveryou have loaded your vehicle heavily,use a tire pressure gauge to ensurethat the tire pressure is at the speci-fied level.

● Do not drive your vehicle over 85MPH (140 km/h) unless it is equippedwith high speed capability tires.Driving faster than 85 MPH (140km/h) may result in tire failure, lossof control and possible injury.

Types of tires

CAUTIONWhen changing or replacing tires, be sureall four tires are of the same type (i.e.,Summer, All Season or Snow) and con-struction. Your NISSAN dealer may beable to help you with information abouttire type, size, speed rating and availabil-ity. Replacement tires may have a lowerspeed rating than the factory equippedtires, and may not match the potentialmaximum vehicle speed. Never exceedthe maximum speed rating of the tire.

All Season tiresNISSAN specifies All Season tires to pro-vide good performance all year, includingsnowy and icy road conditions. All SeasonTires are identified by ‘‘ALL SEASON’’and/or ‘‘M&S’’ on the tire sidewall. Snowtires have better snow traction than AllSeason tires and may be more appropriatein some areas.

Snow tiresIf snow tires are needed, it is necessary toselect tires equivalent in size and load rating

to the original equipment tires. If you do not,it can adversely affect the safety and han-dling of your vehicle.

Generally, snow tires have lower speedratings than factory equipped tires and maynot match the potential maximum vehiclespeed. Never exceed the maximum speedrating of the tire.

For additional traction on icy roads, studdedtires may be used. However, some statesand provinces prohibit their use. Check lo-cal, state and provincial laws before install-ing studded tires. Skid and traction capabili-ties of studded snow tires on wet or drysurfaces may be poorer than that of non-studded snow tires.

Tire chainsUse of tire chains may be prohibited accord-ing to location. Check the local laws beforeinstalling tire chains. When installing tirechains, make sure they are of proper sizefor the tires on your vehicle and are installedaccording to the chain manufacturer’s sug-gestions. Use only SAE Class ‘‘S’’ chains.Other types may damage your vehicle. Usechain tensioners when recommended bythe tire chain manufacturer to ensure a tight

7-26

Z X

fit. Loose end links of the tire chain must besecured or removed to prevent the possibil-ity of whipping action damage to the fendersor undercarriage. If possible, avoid fullyloading your vehicle when using tire chains.In addition, drive at a reduced speed. Do notexceed maximum speed suggested by thechain manufacturer. Otherwise, your ve-hicle may be damaged and/or vehicle han-dling and performance may be adverselyaffected.

Never install tire chains on T-type and smallsize spare tires. Do not use tire chains ondry roads.

Tire rotationNISSAN recommends rotating the tiresevery 7,500 miles (12,000 km).

Tighten wheel nuts to 72 to 87 ft-lb (98 to118 Nzm).

See ‘‘Flat tire’’ in the ‘‘In case of emergency’’section for tire replacing procedures.

WARNING● After rotating the tires, adjust the tire

pressure.

● Retighten the lug nuts after thewheels have been run for the first600 miles (1,000 km) (also in cases ofa flat tire, etc.).

● Do not include the T-type spare tireor any other small size spare tire inthe tire rotation.

ADI0656

7-27

Z X

Tire wear and damageWARNING

● Tires should be periodically in-spected for wear, cracking, bulging,or objects caught in the tread. Ifexcessive wear, cracks, bulging, ordeep cuts are found, the tire shouldbe replaced.

● The original tires have a built-intread wear indicator. When the wearindicator is visible, the tire should bereplaced.

● Improper service for a T-type sparetire may result in serious personalinjury. If it is necessary to repair theT-type spare tire, contact yourNISSAN dealer.

Changing tires and wheelsWhen replacing a tire, use the same size,speed rating and load carrying capacity asoriginally equipped. Recommended typesand sizes are shown in ‘‘Wheels and tires’’in the ‘‘Technical and consumer informa-tion’’ section.

WARNING● The use of tires other than those

recommended or the mixed use oftires of different brands, construc-tion (bias, bias-belted or radial), ortread patterns can adversely affectthe ride, braking, handling, groundclearance, body-to-tire clearance,snow chain clearance, speedometercalibration, headlight aim andbumper height. Some of these ef-fects may lead to accidents andcould result in serious personalinjury.

● If the wheels are changed for anyreason, always replace with wheelswhich have the same offset dimen-sion. Wheels of a different offsetcould cause early tire wear, possiblydegraded vehicle handling charac-teristics and/or interference with thebrake discs/drums. Such interfer-ence can lead to decreased brakingefficiency and/or early brake pad/shoe wear.

● Do not install a deformed wheel ortire even if it has been repaired. Suchwheels or tires could have structuraldamage and could fail without warn-ing.

Wheel balance

Unbalanced wheels may affect vehicle han-dling and tire life. Even with regular use,wheels can get out of balance. Therefore,they should be balanced as required.

Wheel balance service should be performedwith the wheels off the vehicle. Spin balanc-ing the front wheels on the vehicle couldlead to transmission damage.

DI1035M

7-28

Z X

Care of wheels

● Wash the wheels when washing the ve-hicle to maintain their appearance.

● Clean the inner side of the wheels whenthe wheel is changed or the underside ofthe vehicle is washed.

● Do not use abrasive cleaners whenwashing the wheels.

● Inspect wheel rims regularly for dents orcorrosion. Such damage may cause lossof pressure or poor seal at the tire bead.

● NISSAN recommends waxing the roadwheels to protect against road salt in areaswhere it is used during winter.

Spare tire (T-type spare tire)Observe the following precautions if theT-type spare tire must be used, otherwiseyour vehicle could be damaged or involvedin an accident.

WARNING● The T-type spare tire should be used

only for emergency. It should be re-placed by the standard tire at thefirst opportunity.

● Drive carefully while the T-type sparetire is installed. Avoid sharp turnsand abrupt braking while driving.

● Periodically check tire inflation pres-sure, and always keep it at 60 psi(420 kP, 4.2 bar).

● Do not drive your vehicle at speedsfaster than 50 MPH (80 km/h).

● When driving on roads covered withsnow or ice, the T-type spare tireshould be used on the rear wheel andthe original tire used on the frontwheels (drive wheels). Use tire chainsonly on the front two original tires.

● Tire tread of the T-type spare tire willwear at a faster rate than the originaltire. Replace the T-type spare tire assoon as the tread wear indicatorsappear.

● Do not use the T-type spare tire onother vehicles.

● Do not use more than one T-typespare tire at the same time.

● Do not tow a trailer while the T-typespare tire is installed.

CAUTION● Do not use tire chains on a T-type

spare tire. Tire chains will not fitproperly on the T-type spare tire andmay cause damage to the vehicle.

● Because the T-type spare tire issmaller than the original tire, groundclearance is reduced. To avoid dam-age to the vehicle do not drive overobstacles. Also do not drive the ve-hicle through an automatic car washsince it may get caught.

7-29

Z X

Z X

8 Maintenance schedule

General maintenance.............................................8-2Outside the vehicle ................................................8-2Inside the vehicle ...................................................8-3Under the hood and vehicle...................................8-4

Periodic maintenance schedules ...........................8-5Schedule 1 .............................................................8-5Schedule 2 .............................................................8-5Explanation of maintenance items.......................8-10

Z X

Your new NISSAN has been designed tohave minimum maintenance requirementswith longer service intervals to save youboth time and money. However, some day-to-day and regular maintenance is essentialto maintain your NISSAN’s good mechani-cal condition, as well as its emission andengine performance.

It is the owner’s responsibility to make surethe specified maintenance, as well as gen-eral maintenance, is performed.

As the vehicle owner, you are the only onewho can ensure that your vehicle receivesthe proper maintenance care. You are avital link in the maintenance chain.

General maintenance

General maintenance includes those itemswhich should be checked during normalday-to-day operation of the vehicle. Theyare essential if your vehicle is to continue tooperate properly. It is your responsibility toperform these procedures regularly as pre-scribed.

These checks or inspections can be doneby yourself, a qualified technician or, if youprefer, your NISSAN dealer.

Periodic maintenanceThe maintenance items listed in this sectionmust be serviced at regular intervals.

However, under severe driving conditions,additional or more frequent maintenance isrequired.

Where to go for serviceIf maintenance service is required or yourvehicle appears to malfunction, have thesystems checked and tuned by an autho-rized NISSAN dealer.

NISSAN technicians are well-trained spe-cialists and are kept up to date with thelatest service information through technicalbulletins, service tips, and in-dealershiptraining programs. They are completelyqualified to work on NISSAN’s vehicles be-fore they work on your vehicle, rather thanafter they have worked on it.

You can be confident that your NISSANdealer’s service department performs thebest job to meet the maintenance require-ments on your vehicle — in a reliable andeconomic way.

During the normal day-to-day operation ofthe vehicle, general maintenance should beperformed regularly as prescribed in thissection. If you detect any unusual sounds,vibrations or smells, be sure to check for thecause or have your NISSAN dealer do itpromptly. In addition, you should notify yourNISSAN dealer if you think repairs are re-quired.

When performing any checks or mainte-nance work, closely observe the precau-tions in the ‘‘Do-it-yourself operations’’ sec-tion.

Additional information on the followingitems with ‘‘*’’ can be found in the ‘‘Do-it-yourself operations’’ section.

OUTSIDE THE VEHICLEThe maintenance items listed here shouldbe performed from time to time, unlessotherwise specified.

Tires* — Check the pressure with a gaugeperiodically when at a service station, in-cluding the spare, and adjust to the speci-fied pressure if necessary. Check carefullyfor damage, cuts or excessive wear.

Wheel nuts* — When checking the tires,

GENERAL MAINTENANCE

8-2

Z X

make sure no nuts are missing, and checkfor any loose nuts. Tighten if necessary.

Tire rotation* — Tires should be rotatedevery 7,500 miles (12,000 km).

Wheel alignment and balance — If thevehicle should pull to either side while driv-ing on a straight and level road, or if youdetect uneven or abnormal tire wear, theremay be a need for wheel alignment.

If the steering wheel or seat vibrates atnormal highway speeds, wheel balancingmay be needed.

Windshield wiper blades* — Check forcracks or wear if they do not wipe properly.

Doors and engine hood — Check that alldoors and the engine hood operate prop-erly. Also ensure that all latches lock se-curely. Lubricate hinges, latches, rollers andlinks if necessary. Make sure the secondarylatch keeps the hood from opening whenthe primary latch is released.

When driving in areas using road salt orother corrosive materials, check lubricationfrequently.

INSIDE THE VEHICLE

The maintenance items listed here shouldbe checked on a regular basis, such aswhen performing periodic maintenance,cleaning the vehicle, etc.

Lights* — Make sure the headlights, stoplights, tail lights, turn signal lights, and otherlights are all operating properly and installedsecurely. Also check headlight aim.

Warning lights and buzzers/chimes —Make sure all warning lights andbuzzers/chimes are operating properly.

Windshield wiper and washer* — Checkthat the wipers and washer operate properlyand that the wipers do not streak.

Windshield defroster — Check that the aircomes out of the defroster outlets properlyand in sufficient quantity when operating theheater or air conditioner.

Steering wheel — Check for changes inthe steering conditions, such as excessivefreeplay, hard steering or strange noises.

Seats — Check seat position controls suchas seat adjusters, seatback recliner, etc. toensure they operate smoothly and alllatches lock securely in every position.

Check that the head restraints move up anddown smoothly and the locks hold securelyin all latched positions. Check that the seatleg latches lock securely in every anchorposition for the folding down rear seat anddetachable rear seat (if so equipped).

Seat belts — Check that all parts of the seatbelt system (e.g. buckles, anchors, adjust-ers and retractors) operate properly andsmoothly, and are installed securely. Checkthe belt webbing for cuts, fraying, wear ordamage.

Accelerator pedal — Check the pedal forsmooth operation and make sure the pedaldoes not catch or require uneven effort.Keep the floor mats away from the pedal.

Brakes — Check that the brakes do not pullthe vehicle to one side when applied.

Brake pedal* — Check the pedal forsmooth operation and make sure it has theproper distance under it when depressedfully. Check the brake booster function. Becertain to keep floor mats away from thepedal.

Parking brake* — Check that the pedal isadjusted to specification and confirm thatyour vehicle is held securely on a fairly

8-3

Z X

steep hill with only the parking brake ap-plied.

Automatic transmission ‘‘Park’’ mecha-nism — On a fairly steep hill check that yourvehicle is held securely with the selectorlever in the P (Park) position without apply-ing any brakes.

UNDER THE HOOD ANDVEHICLE

The maintenance items listed here shouldbe checked periodically, for example, eachtime you check the engine oil or refuel.

Windshield washer fluid* — Check thatthere is adequate fluid in the tank.

Engine coolant level* — Check the cool-ant level when the engine is cold.

Radiator and hoses — Check the front ofthe radiator and clean off any dirt, insects,leaves, etc., that may have accumulated.Make sure the hoses have no cracks, de-formation, rot, or loose connections.

Brake fluid level* — Make sure the brakefluid level is between the MAX and MINlines on the reservoir.

Battery* — Check the fluid level in each

cell. It should be between the MAX and MINlines.

Engine drive belts* — Make sure no beltsare frayed, worn, cracked or oily.

Engine oil level* — Check the level afterparking the vehicle on a level surface andturning off the engine.

Power steering fluid level* and lines —Check the level when the fluid is cold andthe engine is turned off. Check the lines forproper attachment, leaks, cracks, etc.

Automatic transmission fluid level* —Check the level after putting the selectorlever in P (Park) with the engine idling.

Exhaust system — Make sure there are nocracks, holes, loose joints or supports. If thesound of the exhaust seems unusual orthere is a smell of exhaust fumes, immedi-ately have the exhaust system inspected bya qualified individual. (See the carbon mon-oxide warning in the ‘‘Starting and driving’’section.)

Underbody — The underbody is frequentlyexposed to corrosive substances such asthose used on icy roads or to control dust. Itis very important to remove these sub-

stances, otherwise rust forms on the floorpan, frame, fuel lines and around the ex-haust system. At the end of winter, theunderbody should be thoroughly flushedwith plain water, being careful to cleanthose areas where mud and dirt may accu-mulate. See the ‘‘Appearance and interiorcare’’ section for additional information.

Fluid leaks — Check under the vehicle forfuel, oil, water or other fluid leaks after thevehicle has been parked for a while. Waterdripping from the air conditioner after use isnormal. If you should notice any leaks or ifgasoline fumes are evident, check for thecause and have it corrected immediately.

8-4

Z X

To ensure smooth, trouble-free, safe andeconomical driving, NISSAN provides twodifferent maintenance schedules that maybe used, depending upon the conditions inwhich you usually drive. These schedulescontain both distance and time intervals, upto 60,000 miles (96,000 km)/48 months. Formost people, the odometer reading indi-cates when service is needed. However, ifyou drive very little, your vehicle should beserviced at the regular time intervals shownin the schedule. After 60,000 miles (96,000km) or 48 months, continue periodicmaintenance at the same mileage/timeintervals.

SCHEDULE 1

Follow Periodic Maintenance Schedule 1 ifyour driving habits frequently include one ormore of the following driving conditions:

● Repeated short trips of less than 5miles (8 km).

● Repeated short trips of less than 10miles (16 km) with outside tempera-tures remaining below freezing.

● Operating in hot weather in stop-and-go ‘‘rush hour’’ traffic.

● Extensive idling and/or low speeddriving for long distances, such aspolice, taxi or door-to-door deliveryuse.

● Driving in dusty conditions.

● Driving on rough, muddy, or saltspread roads.

● Towing a trailer, using a camper or acar-top carrier.

SCHEDULE 2

Follow Periodic Maintenance Schedule 2 ifnone of the driving conditions shown inSchedule 1 apply to your driving habits.

PERIODIC MAINTENANCESCHEDULES

8-5

Z X

Schedule 1Abbreviations: R = Replace I = Inspect. Correct or replace if necessary. [ ]: At the mileage intervals only

MAINTENANCE OPERATION MAINTENANCE INTERVALPerform at number of miles,kilometers or months,whichever comes first.

Miles × 1,000 3.75 7.5 11.25 15 18.75 22.5 26.25 30 33.75 37.5 41.25 45 48.75 52.5 56.25 60(km × 1,000) (6) (12) (18) (24) (30) (36) (42) (48) (54) (60) (66) (72) (78) (84) (90) (96)Months 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48

Emission control system maintenance

Drive belts See NOTE (1). I*Air cleaner filter See NOTE (2). [R] [R]Vapor lines I* I*Fuel lines I* I*Fuel filter See NOTE (3)*.Engine coolant Replace every 30,000 miles (48,000 km) or 36 months.*Engine oil R R R R R R R R R R R R R R R REngine oil filter (Use NISSAN Premium type or equivalent.) R R R R R R R R R R R R R R R RSpark plugs [R] [R]Timing belt Replace every 105,000 miles (168,000 km).

NOTE: (1) After 60,000 miles (96,000 km) or 48 months, inspect every 15,000 miles (24,000 km) or 12 months.(2) If operating mainly in dusty conditions, more frequent maintenance may be required.(3) If vehicle is operated under extremely adverse weather conditions or in areas where ambient temperatures are either extremely low or

extremely high, the filters might become clogged. In such an event, replace them immediately.* Maintenance items and intervals with ‘‘*’’ are recommended by NISSAN for reliable vehicle operation. The owner need not perform such

maintenance in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals arerequired.

8-6

Z X

Abbreviations: I = Inspect. Correct or replace if necessary.

MAINTENANCE OPERATION MAINTENANCE INTERVAL

Perform at number of miles,kilometers or months, whichevercomes first.

Miles × 1,000 7.5 15 22.5 30 37.5 45 52.5 60

(km × 1,000) (12) (24) (36) (48) (60) (72) (84) (96)

Months 6 12 18 24 30 36 42 48

Chassis and body maintenance

Brake lines & cables I I I I

Brake pads, discs, drums & linings I I I I I I I I

Automatic transmission fluid See NOTE (1). I I I I

Steering gear & linkage, axle & suspension parts I I I I I I I I

Steering linkage ball joints & front suspension ball joints I I I I I I I I

Exhaust system I I I I I I I I

Front drive shaft boots I I I I I I I I

Supplemental air bag system See NOTE (2).

NOTE: (1) If towing a trailer, using a camper or a car-top carrier, or driving on rough or muddy roads, change (not just inspect) fluid at every30,000 miles (48,000 km) or 24 months.

(2) Inspect the supplemental air bag system 10 years after the date of manufacture as noted on the F.M.V.S.S. certification label locatedon the left center pillar.

8-7

Z X

Schedule 2Abbreviations: R = Replace I = Inspect. Correct or replace if necessary. [ ]: At the mileage intervals only


Perform at number of miles,kilometers or months, whichever comes first.

Miles × 1,000 7.5 15 22.5 30 37.5 45 52.5 60

(km × 1,000) (12) (24) (36) (48) (60) (72) (84) (96)

Months 6 12 18 24 30 36 42 48

Emission control system maintenance

Drive belts See NOTE (1). I*

Air cleaner housing filter [R] [R]

Vapor lines I* I*

Fuel lines I* I*

Fuel filter See NOTE (2)*.

Engine coolant Replace every 30,000 miles (48,000 km) or 36 months.*

Engine oil R R R R R R R R

Engine oil filter (Use NISSAN Premium type, or equivalent.) R R R R R R R R

Spark plugs [R] [R]

Timing belt Replace every 105,000 miles (168,000 km).

NOTE: (1) After 60,000 miles (96,000 km) or 48 months, inspect every 15,000 miles (24,000 km) or 12 months.(2) If vehicle is operated under extremely adverse weather conditions or in areas where ambient temperatures are either extremely low or

extremely high, the filters might become clogged. In such an event, replace them immediately.* Maintenance items and intervals with ‘‘*’’ are recommended by NISSAN for reliable vehicle operation. The owner need not perform such

maintenance in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals arerequired.

8-8

Z X

Abbreviations: I = Inspect. Correct or replace if necessary.


Perform at number of miles, kilome-ters or months, whichever comesfirst.

Miles × 1,000(km × 1,000)Months

7.5(12)

6

15(24)12

22.5(36)18

30(48)24

37.5(60)30

45(72)36

52.5(84)42

60(96)48

Chassis and body maintenance

Brake lines & cables I I I I

Brake pads, discs, drums & linings I I I I

Automatic transmission oil I I I I

Steering gear linkage, axle & suspension parts I I

Exhaust system See NOTE (1). I I

Front drive shaft boots I I I I

Supplemental air bag system See NOTE (2).

NOTE: (1) After 60,000 miles (96,000 km) or 48 months, inspect every 15,000 miles (24,000 km) or 12 months.(2) Inspect the supplemental air bag system 10 years after the date of manufacture as noted on the F.M.V.S.S. certification label located

on the left center pillar.

8-9

Z X

Additional information on the followingitems with ‘‘*’’ is found in the ‘‘Do-it-yourself operations’’ section.

Emission control systemmaintenance

Drive belts* — Check drive belts for wear,fraying or cracking and also for proper ten-sion. Replace the drive belts if found dam-aged.

Air cleaner filter — Under normal drivingconditions, the air cleaner filter should bereplaced in accordance with the mainte-nance schedule. However, driving the ve-hicle in dusty areas may cause more rapidclogging of the element. Consequently, theelement may have to be replaced morefrequently.

Vapor lines — Check vapor lines and con-nections for failure or looseness. If leaks arefound, replace them.

Fuel lines — Check the fuel hoses, pipingand connections for leaks, looseness ordeterioration. Replace any parts if they aredamaged.

Fuel filter — If the vehicle is operatedunder extremely adverse weather condi-

tions or in areas where ambient tempera-tures are either extremely low or extremelyhigh, the filter might become clogged. Insuch an event, replace the filter immedi-ately.

Engine coolant* — Changing engine cool-ant can be performed by your NISSANdealer or procedures can be found in theService Manual. Improper air relief afterchanging coolant can result in reducedheater performance and overheating.

Engine oil & oil filter* — Under normaldriving conditions, the engine oil and oil filtershould be replaced in accordance with themaintenance schedule. However, under se-vere driving conditions, they may have to bereplaced more frequently.

Spark plugs* — Replace with new plugshaving the correct heat range.

Timing belt — Replace the timing belt fordriving the camshaft.

Chassis and body maintenanceBrake lines & cables — Check the brakelines and hoses (including brake boostervacuum hoses, connections & check valve)and parking brake cables for proper attach-

ment, leaks, cracks, chafing, abrasion, de-terioration, etc.

Brake pads, discs, drums & linings —Check these and the other neighboringbrake components for wear, deteriorationand leaks. Under severe driving conditions,they may have to be inspected more fre-quently.

Automatic transmission fluid* — Checkthe fluid level and visually inspect for signsof leakage.

Under severe driving conditions, the fluidshould be replaced at the specified interval.

Steering gear & linkage, axle & suspen-sion parts, and drive shaft boots —Check for damage, looseness and leakageof oil or grease. Under severe driving con-ditions, more frequent inspection should beperformed.

Steering linkage ball joints & front sus-pension ball joints — Check the ball jointsfor damage, looseness and grease leakage.

EXPLANATION OFMAINTENANCE ITEMS

8-10

Z X

Exhaust system — Visually check the ex-haust pipes, muffler, and hangers for properattachment, leaks, cracks, chafing, abra-sion, deterioration, etc. Under severe driv-ing conditions, inspection should be per-formed more frequently.

Supplemental air bag system — Checkthe supplemental air bag system compo-nents for proper attachment, damage, de-formities, cracks, rust, etc. Work around andon the supplemental air bag system shouldbe done by an authorized NISSAN dealer.

8-11

Z X

Z X

9 Technical and consumer information

Capacities and recommended fuel/lubricants........9-2Fuel recommendation.............................................9-2Engine oil and oil filter recommendation................9-4Recommended SAE viscosity number...................9-6Air conditioner system refrigerant andlubricant recommendations ....................................9-6Engine ....................................................................9-7Wheel/tire size........................................................9-8Dimensions and weights ........................................9-8Registering your vehicle in another country ..........9-9Vehicle identification ..............................................9-9Vehicle identification number (VIN) plate...............9-9Engine serial number .............................................9-9

F.M.V.S.S. certification label ................................9-10Emission control information label .......................9-10Tire placard ..........................................................9-11Air conditioner specification label.........................9-11Installing the license plate....................................9-11Vehicle loading information..................................9-12Trailer towing........................................................9-13Uniform tire quality grading..................................9-18Emission control system warranty .......................9-19Reporting safety defects (USA) ...........................9-19Readiness for inspection/maintenance (I/M)test........................................................................9-20

Z X

The following are approximate capacities. The actual refill capacities may be a littledifferent. When refilling, follow the procedure instructed in the ‘‘Do-it-yourself’’section to determine the proper refill capacity.

Capacity (Approximate)Recommended Fluids & LubricantsUS

measureImp

measure Liter

Fuel 20 gal 16-5/8 gal 75.7 Unleaded gasoline with an octane rat-ing of at least 87 AKI (RON 91)(1)

Engine oil (Refill)With oil filter 4-1/4 qt 3-1/2 qt 4.0 API SG or SH and Energy Conserving II (2)

API Certification Mark (2)Without oil filter 3-7/8 qt 3-1/8 qt 3.6Cooling system

With reservoir tankWith rear heater 12-3/4 qt 10-5/8 qt 12.1 Anti-freeze coolant

(Ethylene glycol base)Without rear heater 11-3/8 qt 9-3/8 qt 10.7Reservoir 3/4 qt 5/8 qt 0.7

Automatic transaxle fluidNISSAN matic ‘D’ (Continental U.S. andAlaska) or Genuine Nissan AutomaticTransmission Fluid (Canada).(3)

Power steering fluidRefill to the proper oil levelaccording to the instructions in the‘‘Do-it-yourself’’ section.

Type F automatic transmission fluid orequivalent

Brake fluidGenuine NISSAN Brake Fluid(4) orequivalentDOT 3 (US FMVSS No. 116)

Multi-purpose grease — — — NLGI No. 2 (Lithium complex)Air conditioning system refrigerant — — — HFC-134a (R-134a)(5)

(1): For further details, see ‘‘Fuel recommendation’’.(2): For further details, see ‘‘Recommended SAE engine oil viscosity’’.(3): DexronT III/MerconT or equivalent may also be used. Outside the Continental United States and Alaska

contact a NISSAN dealership for more information regarding suitable fluids, including recommendedbrand(s) of DexronT III/MerconT Automatic Transmission Fluid.

(4): Available in mainland U.S.A. through an authorized NISSAN dealer.(5): For further details, see ‘‘Air conditioner specification label’’.

FUEL RECOMMENDATIONAll models are designed to operate onunleaded gasoline with an octane ratingof at least 87 AKI (Anti-Knock Index)number (Research octane number 91).

CAUTION● Using a fuel other than that specified

could adversely affect the emissioncontrol devices and systems, andcould also affect warranty coverage.

● Under no circumstances should aleaded gasoline be used, since thiswill damage the three way catalyst.

Reformulated gasolineSome fuel suppliers are now producing re-formulated gasolines. These gasolines arespecially designed to reduce vehicle emis-sions. NISSAN supports efforts towardscleaner air and suggests that you use refor-mulated gasoline when available.

CAPACITIES AND RECOMMENDEDFUEL/LUBRICANTS

9-2

Z X

Gasoline containing oxygenates

Some fuel suppliers sell gasoline containingoxygenates such as ethanol, MTBE andmethanol with or without advertising theirpresence. NISSAN does not recommendthe use of fuels of which the oxygenatecontent and the fuel compatibility for yourNISSAN cannot be readily determined. If indoubt, ask your service station manager.

If you use oxygenate-blend gasoline, pleasetake the following precautions as the usageof such fuels may cause vehicle perfor-mance problems and/or fuel system dam-age.

● The fuel should be unleaded and havean octane rating no lower than thatrecommended for unleaded gasoline.

● If an oxygenate-blend, excepting amethanol blend, is used, it shouldcontain no more than 10% oxygenate.(MTBE may, however, be added up to15%.)

● If a methanol blend is used, it shouldcontain no more than 5% methanol(methyl alcohol, wood alcohol). Itshould also contain a suitable amountof appropriate cosolvents and corro-

sion inhibitors. If not properly formu-lated with appropriate cosolvents andcorrosion inhibitors, such methanolblends may cause fuel system dam-age and/or vehicle performance prob-lems. At this time, sufficient data isnot available to ensure that all metha-nol blends are suitable for use inNISSAN vehicles.

If any undesirable driveability problemssuch as engine stalling and difficult hot-starting are experienced after usingoxygenate-blend fuels, immediately changeto a non-oxygenate fuel or a fuel with a lowblend of MTBE.

Take care not to spill gasoline duringrefueling. Gasoline containing oxygen-ates can cause paint damage.

Aftermarket fuel additives

NISSAN does not recommend the use ofany fuel additives (i.e.: fuel injector cleaner,octane booster, intake valve deposit remov-ers, etc.) which are sold commercially.Many of these additives intended for gum,varnish or deposit removal may containactive solvents or similar ingredients that

can be harmful to the fuel system andengine.

Octane rating tipsIn most parts of North America, you shoulduse unleaded gasoline with an octane ratingof at least 87 AKI (Anti-Knock Index) num-ber. However, you may use unleaded gaso-line with an octane rating as low as 85 AKI(Anti-Knock Index) in high altitude areas(over 4,000 ft [1,219 m]) such as: Colorado,Montana, New Mexico, Utah, Wyoming,northeastern Nevada, southern Idaho,western South Dakota, western Nebraska,and the part of Texas which is directly southof New Mexico.

Using unleaded gasoline with an octanerating lower than stated above can causepersistent, heavy ‘‘spark knock.’’ (‘‘Sparkknock’’ is a metallic rapping noise.) Ifsevere, this can lead to engine damage. Ifyou detect a persistent heavy sparkknock even when using gasoline of thestated octane rating, or if you hear steadyspark knock while holding a steadyspeed on level roads, have an authorizeddealer correct the condition. Failure tocorrect the condition is misuse of thevehicle, for which NISSAN is not respon-sible.9-3

Z X

Incorrect ignition timing may result in sparkknock, after-run, and/or overheating, whichmay cause excessive fuel consumption orengine damage. If any of the above symp-toms are encountered, have your vehiclechecked at an authorized NISSAN dealer orother competent service facility.

However, now and then you may noticelight spark knock for a short time whileaccelerating or driving up hills. This isno cause for concern, because you getthe greatest fuel benefit when there islight spark knock for a short time underheavy engine load.

ENGINE OIL AND OIL FILTERRECOMMENDATION

Selecting the correct oil

It is essential to chose engine oil with thecorrect quality and viscosity to ensure sat-isfactory engine life and performance. NIS-SAN recommends the use of a low frictionoil (energy conserving oil) in order to im-prove fuel economy and conserve energy.Oils which do not have the specified qualitylabel should not be used as they couldcause engine damage.

Only those engine oils with the AmericanPetroleum Institute (API) CERTIFICATIONMARK on the front of the container shouldbe used. This type of oil supersedes theexisting API SG or SH and Energy Conserv-ing II categories.

If you cannot find engine oil with the CER-TIFICATION MARK, an API SG or SH, anEnergy Conserving II oil with the API Ser-vice Symbol may be used. An oil with asingle designation SG or SH, or in combi-nation with other categories (for example,SG/CC or SG/CD) may also be used if onewith the

ATI0507

9-4

Z X

API CERTIFICATION MARK cannot befound.

Mineral based or synthetic type oils may beused in your NISSAN vehicle. These oilsmust, however, meet the API quality andSAE viscosity ratings specified for your ve-hicle. Do not mix mineral based and syn-thetic type oils in the engine.

Oil additives

NISSAN does not recommend the use of oiladditives. The use of an oil additive is notnecessary when the proper oil type is usedand maintenance intervals are followed.

Oil which may contain foreign matter or hasbeen previously used should not be used.

Oil viscosity

The engine oil viscosity or thicknesschanges with temperature. Because of this,it is important to select the engine oil viscos-ity based on the temperatures at which thevehicle will be operated before the next oilchange. The chart ‘‘Recommended SAEviscosity number’’ shows the recommendedoil viscosities for the expected ambient tem-peratures. Choosing an oil viscosity other

than that recommended could cause seri-ous engine damage.

Selecting the correct oil filterYour new NISSAN vehicle is equipped witha high- quality genuine NISSAN oil filter.When replacing, use a genuine NISSAN oilfilter or its equivalent for the reason de-scribed in ‘‘Change intervals’’.

Change intervalsThe oil and oil filter change intervals for yourengine are based on the use of the specifiedquality oils and filters. Oil and filter otherthan the specified quality, or oil and filterchange intervals longer than recommendedcould reduce engine life. Damage to theengine caused by improper maintenance oruse of incorrect oil and filter quality and/orviscosity is not covered by the new NISSANvehicle warranties.

Your engine was filled with a high qualityengine oil when it was built. You do not haveto change the oil before the first recom-mended change interval. Oil and filterchange intervals depend upon how you useyour vehicle. Operation under the followingconditions may require more frequent oiland filter changes:

— repeated short distance driving at coldoutside temperatures,

— driving in dusty conditions,

— extensive idling,

— towing a trailer.

9-5

Z X

RECOMMENDED SAEVISCOSITY NUMBER

● SAE 5W-30 viscosity oil is preferredfor all temperatures. SAE 10W-30 vis-cosity oil may be used if the ambienttemperature is above 0°F (-18°C).

AIR CONDITIONER SYSTEMREFRIGERANT AND LUBRICANTRECOMMENDATIONSThe air conditioning system in thisNISSAN vehicle must be charged withthe refrigerant HFC-134a (R-134a) andthe lubricant, NISSAN type ‘‘PAG F’’ orthe exact equivalents.

CAUTIONUse of any other refrigerant or lubricantwill cause severe damage and you willneed to replace your vehicle’s entire airconditioning system.

The refrigerant HFC-134a (R-134a) in yourNISSAN vehicle does not harm the earth’sozone layer. Although this refrigerant doesnot affect the earth’s atmosphere, certaingovernment regulations require the recov-ery and recycling of any refrigerant duringautomative air conditioning system service.An authorized NISSAN dealer has thetrained technicians and equipment neededto recover and recycle your air conditioningsystem refrigerant.

Contact an authorized NISSAN dealer whenservicing your air conditioning system.

ATI0509

9-6

Z X

Model VG30EType Gasoline, 4-cycleCylinder arrangement 6-cylinder, V slanted at 60°Bore × Stroke in (mm) 3.425 × 3.268 (87.0 × 83.0)Displacement cu in (cm3) 180.62 (2,960)Firing order 1,2,3,4,5,6* (See illustration below)Idle speed rpm

See the ‘‘Important Vehicle Information’’ label on the underside of the hood.Ignition timing degree (B.T.D.C.)at idle speed degree/rpmCO percentage at idle speed[No air] %Spark plug

Standard BKR5EYCold BKR6EY

Spark plug gap in (mm) 0.031 to 0.035 (0.8 to 0.9)Camshaft operation Timing belt** (See note below)Drive belts[Width × Length] in (mm)

Generator belt 0.7008 × 33.66 (17.80 × 855)Air conditioner compressor 0.5606 × 46.65 (14.24 × 1,185)Power steering pump 0.5606 × 40.74 (14.24 × 1,035)

**NOTE: Periodic maintenance is necessary. Refer to the appropriate periodicmaintenance schedule in Chapter 8.

The spark ignition system of this vehicle meets all requirements of theCanadian Interference-Causing Equipment Regulations.

ENGINE

9-7

Z X

Road wheel Steel 5.5 - JJ × 15

Aluminum 6.5 - JJ × 15

Offset in (mm) 1.77 (45)

Tire size Conventional P205/75R15 97 S

Cast aluminum* P205/75R15 97 SP215/70R15 97 T

Spare T125/90D16P205/75R15 97 S*P215/70R15 97 T*

*: Option

Overall length in (mm) 189.9 (4,824)

Overall width in (mm) 73.7 (1,871)

Overall height in (mm) 67.6 (1,716)

Front tread in (mm) 63.4 (1,610)

Rear tread in (mm) 63.4 (1,610)

Wheelbase in (mm) 112.2 (2,850)

Gross vehicle weightrating lb (kg)

See the ‘‘F.M.V.S.S. certification label’’on the left center pillar.

Gross axle weight rating

Front lb (kg)

Rear lb (kg)

WHEEL/TIRE SIZE DIMENSIONS AND WEIGHTS

9-8

Z X

When planning to travel in another coun-try, you should first find out if the fuelavailable is suitable for your vehicle’s en-gine.Using fuel with an octane/cetane rating thatis too low may cause engine damage. Allgasoline vehicles must be operated withunleaded gasoline. Therefore, avoid takingyour vehicle to areas where appropriate fuelis not available.When transferring the registration ofyour vehicle to another country, state,province or district, it may be necessary tomodify the vehicle to meet local laws andregulations.The laws and regulations for motor vehicleemission control and safety standards varyaccording to the country, state, province ordistrict. Therefore, vehicle specificationsmay differ.When any vehicle is to be taken intoanother country, state, province or dis-trict and registered, its modifications,transportation, and registration are theresponsibility of the user. NISSAN is notresponsible for any inconvenience thatmay result.

VEHICLE IDENTIFICATIONNUMBER (VIN) PLATEThe vehicle identification number plate isattached to the upper portion of the dash-board on the driver’s side. This number isthe identification for your vehicle and isused in the vehicle registration.

ENGINE SERIAL NUMBER

The number is stamped on the engine asshown.

ATI0563 ATI0550

REGISTERING YOUR VEHICLEIN ANOTHER COUNTRY

VEHICLE IDENTIFICATION

9-9

Z X

F.M.V.S.S. CERTIFICATIONLABEL

The F.M.V.S.S. certification label is affixedas shown. This label contains valuable ve-hicle information, such as: Gross Vehicle

Weight Rating (GVWR), Gross Axle WeightRating (GAWR), month and year of manu-facture, Vehicle Identification Number(VIN), etc. Review it carefully.

EMISSION CONTROLINFORMATION LABELThe emission control information label isattached as shown.

ATI0560

ATI0005

9-10

Z X

TIRE PLACARDThe cold tire pressure is shown on the tireplacard affixed to the inside of the glovebox.

AIR CONDITIONERSPECIFICATION LABELThe air conditioner specification label isattached as shown.

Have your front license plate installed byyour NISSAN dealer.

ATI0561 ATI0562

ATI0564

INSTALLING THE LICENSEPLATE

9-11

Z X

WARNING



● Be sure everyone in your vehicle is ina seat and using a seat belt properly.

Terms

It is important to familiarize yourself with thefollowing terms before loading your vehicle:

● Curb Weight (actual weight of your ve-hicle) - vehicle weight including: standardand optional equipment, fluids, emer-gency tools, and spare tire assembly.This weight does not include passen-gers and cargo.

● GVW (Gross Vehicle Weight) - curbweight plus the combined weight of pas-sengers and cargo.

● GVWR (Gross Vehicle Weight Rating) -

maximum total weight (load) limit speci-fied for the vehicle.

● GAWR (Gross Axle Weight Rating) -maximum weight (load) limit specified forthe front or rear axle.

● Gross combined weight - GVW plus thetotal weight of the trailer and all its cargo.

Determining Vehicle Load CapacityThe load capacity of this vehicle is deter-mined by weight, not by available cargospace. For example, a luggage rack, bikecarrier, cartop carrier or similar equipmentdoes not increase load carrying capacity ofyour vehicle.

To determine vehicle load capacity:

Vehicle weight can be determined by usinga commercial-grade scale, found at placessuch as a truck stop, gravel quarry, grainelevator, or a scrap metal recycling facility.

1) Determine the curb weight of your vehicle.

2) Compare the curb weight amount to theGVWR specified for your vehicle to de-termine how much more weight yourvehicle can carry.

3) After loading (cargo & passengers), re-

weigh your vehicle to determine if eitherGVWR or GAWR for your vehicle isexceeded. If GVWR is exceeded, re-move cargo as necessary. If either thefront or rear GAWR is exceeded, shiftthe load or remove cargo as necessary.

Loading Tips● The GVW must not exceed GVWR or

GAWR specified on the F.M.V.S.S. Cer-tification Label.

● Do not load the front and rear axle to theGAWR. Doing so will exceed the GVWR.

WARNING● Properly secure all cargo to help pre-

vent it from sliding or shifting. Do notplace cargo higher than the seat-backs. In a sudden stop or collision,unsecured cargo could cause per-sonal injury.

● Do not load your vehicle any heavierthan the GVWR or the maximumfront and rear GAWRs. If you do,parts on your vehicle can break, or itcan change the way your vehiclehandles. This could result in loss ofcontrol and cause personal injury.

VEHICLE LOADINGINFORMATION

9-12

Z X

● Overloading can shorten the life ofyour vehicle. Failures caused byoverloading are not covered by yourwarranty.

Your new vehicle was designed to be usedprimarily to carry passengers and cargo.Remember that towing a trailer places ad-ditional loads on your vehicle’s engine, drivetrain, steering, braking and other systems.

Information on trailer towing ability and thespecial equipment required should be ob-tained from an authorized NISSAN dealer.He can obtain a NISSAN Towing Guide foryou.

Do not tow a trailer if your vehicle is a cargovan model.

Maximum load limits

Maximum trailer loads

Never allow the total trailer load to exceed3,500 lbs (1,588 kg). The total trailer loadequals trailer weight plus its cargo weight.Towing loads greater than 3,500 lbs (1,588kg) or using improper towing equipmentcould adversely affect vehicle handling,braking and performance.

● All towing above 1,000 lbs (454 kg) re-quires the use of trailer brakes.

● NISSAN recommends the use of a tan-dem axle trailer whenever towing above3,000 lbs (1,361 kg).

● A sway control device is recommendedfor all towing above 2,000 lbs (907 kg).Sway control devices are not offered byNISSAN. See a professional trailer/hitchoutlet for a properly designed sway con-trol device for your trailer.

The Gross Combined Weight should notexceed 8,000 lbs (3,628 kg). The GrossCombined Weight is the total weight of thetow vehicle with all occupants, cargo andfuel tanks, PLUS the total weight of thetrailer and all its cargo. This weight should

TI1011M

TRAILER TOWING

9-13

Z X

be properly distributed. For more informa-tion regarding vehicle and trailer loading,refer to The NISSAN Towing Guide, avail-able from an authorized Nissan dealer.

WARNINGVehicle damage and/or personal injuryresulting from improper towing proce-dures is not covered by NISSAN war-ranties. Information on trailer towingand required towing equipment shouldbe obtained from dealers who special-ize in providing trailers or other towingequipment.

Tongue load:

Keep the tongue load between 9 and 11%of the total trailer load. If the tongue loadbecomes excessive, rearrange cargo to al-low for proper tongue load.

Maximum gross vehicle weight/maximumgross axle weight

The gross vehicle weight of the towingvehicle must not exceed the gross vehicleweight rating (GVWR) shown on theF.M.V.S.S. certification label. The gross ve-hicle weight equals the combined weight ofthe unloaded vehicle, passengers, luggage,hitch, trailer tongue load and any otheroptional equipment. In addition, front or reargross axle weight must not exceed thegross axle weight rating (GAWR) shown onthe F.M.V.S.S. certification label.

TOWING LOAD/SPECIFICATION CHART

UNIT: lb (kg)

MAXIMUMTOWING LOAD

3,500 (1,588)(See below)

MAXIMUMTONGUE LOAD

350 (159)

Trailer hitchChoose a proper hitch for your vehicle andtrailer. Make sure the trailer hitch is securelyattached to the vehicle to help avoid per-sonal injury or property damage due tosway caused by crosswinds, rough roadsurfaces or passing trucks.

CAUTION● Do not use axle-mounted hitches.

● The hitch should not be attached toor affect the operation of the impact-absorbing bumper.

● Do not modify the vehicle exhaustsystem, brake system, etc. when thehitch is installed.

TI1012M

9-14

Z X

● To reduce the possibility of addi-tional damage if your vehicle isstruck from the rear, where practicalremove the hitch when not in use.Remove the receiver when not inuse. After the hitch is removed, sealthe bolt holes to prevent exhaustfumes, water or dust from enteringthe passenger compartment.

● Regularly check that all hitch mount-ing bolts are securely mounted.

Tire pressures● When towing a trailer, inflate the vehicle

tires to the recommended cold tire pres-sure indicated on the tire placard (locatedon the inside of the glove box lid).

● Trailer tire condition, size, load rating andproper inflation pressure should be inaccordance with the trailer and tiremanufacturer’s specifications.

Safety chainAlways use suitable safety chains betweenyour vehicle and the trailer. Safety chainsshould be crossed and should be attachedto the hitch, not to the vehicle bumper or

axle. Be sure to leave enough slack in thechain to permit turning corners.

Trailer lights

Trailer lights should comply with Federaland/or local regulations. When wiring thevehicle for towing, connect the stop and taillight pickup into the vehicle electrical circuit.

Class I Trailer Tow electrical wiring providestwo circuits (right and left hand) to operatetrailer stop/turn tail lamps. Each individualstop/turn circuit will operate only one com-bination stop/turn light bulb (#1157, 3157,2357, or 3357) on the trailer. Never addmore than one trailer light bulb to onecircuit.

9-15

Z X

Trailer Tow Harness and Module(if so equipped)

The trailer tow module on your vehicle al-lows turn/stop lamp control of a trailer beingtowed by your NISSAN.

The trailer tow module includes:

● trailer tow module which draws powerfrom the vehicle stop lamp fuse

● one subharness containing a SAE J1239specified connector

To use the tow harness:

1) Remove the connector cap from thevehicle harness, located behind the rearbumper. Store the connector cap in ve-hicle glove box for reinstallation.

2) Connect the tow harness to the vehicleharness located behind the rear bumper.

3) Connect the tow harness connector(SAE J1239) to your trailer.

4) Confirm proper vehicle and trailerstop/turn lamp operation.

5) When towing is completed, disconnectthe tow harness from the trailer and thevehicle. Store the tow harness in theglove box. Reinstall the connector cap tothe vehicle harness.

If you need further assistance in wiringa trailer to your NISSAN, contact an autho-rized NISSAN dealer.

Always confirm proper vehicle andtrailer stop/turn lamp operation everytime the trailer light circuits are con-nected for use.

ATI0555

9-16

Z X

Trailer brakes

If your trailer is equipped with a brakingsystem, make sure it conforms to Federaland/or local regulations and it is properlyinstalled.

WARNING

Never connect a trailer brake systemdirectly to the vehicle brake system.

Pre-towing tips

● Be certain your vehicle maintains a levelposition when a loaded and/or unloadedtrailer is hitched. Do not drive the vehicleif it has an abnormal nose-up or nose-down condition; check for impropertongue load, overload, worn suspensionor other possible causes of either condi-tion.

● Always secure items in the trailer toprevent load shift while driving.

● Be certain your rear view mirrors conformto all federal, state or local regulations. Ifnot, install any mirrors required for towingbefore driving the vehicle.

Trailer towing tips

In order to gain skill and an understandingof the vehicle’s behavior, you should prac-tice turning, stopping and backing up in anarea which is free from traffic. Steering,stability, and braking performance aresomewhat different than under normal driv-ing conditions.

● Always secure items in the trailer toprevent load shift while driving.

● Avoid abrupt starts, acceleration or stops.

● Avoid sharp turns or lane changes.

● Always drive your vehicle at a moderatespeed.

● Always block the wheels on both vehicleand trailer when parking. Parking on aslope is not recommended; however, ifyou must do so, first block the wheelsand apply the parking brake, and thenmove the transmission shift selector le-ver into the P (Park) position. If you movethe shift selector lever to the P (Park)position before blocking the wheels andapplying the parking brake, transmissiondamage could occur.

● When going down a hill, shift into a lower

gear and use the engine braking effect.When ascending a long grade, downshiftthe transmission to a lower gear andreduce speed to reduce chances of en-gine overloading and/or overheating.

● If the engine coolant rises to an ex-tremely high temperature when the airconditioning system is on, turn the airconditioner off. Coolant heat can be ad-ditionally vented by opening the win-dows, switching the fan control dial tohigh and setting the temperature controldial to the WARM position.

● Trailer towing requires more fuel thannormal circumstances.

● Avoid towing a trailer for the first 500miles (800 km) of the vehicle’s life.

● Have your vehicle serviced more oftenthan at intervals specified in the recom-mended Maintenance Schedule.

● When making a turn, your trailer wheelswill be closer to the inside of the turn thanyour vehicle wheels. To compensate forthis, make a larger than normal turningradius during the turn.

● Crosswinds and rough roads adversely9-17

Z X

affect vehicle/trailer handling, possiblycausing vehicle sway. When beingpassed by larger vehicles, be preparedfor possible changes in crosswinds thatcould affect vehicle handling. If swayingdoes occur, firmly grip the steeringwheel, steer straight ahead, and immedi-ately (but gradually) reduce vehiclespeed. This combination helps to stabi-lize the vehicle. Never increase speed.

● Be careful when passing other vehicles.Passing while towing a trailer requiresconsiderably more distance than normalpassing. Remember the length of thetrailer must also pass the other vehiclebefore you can safely change lanes.

● To maintain engine braking efficiencyand electrical charging performance, donot use overdrive.

● Avoid holding the brake pedal down toolong or too frequently. This could causethe brakes to overheat, resulting in re-duced braking efficiency.

When towing a trailer, change fluid in thetransmission more frequently. For addi-tional information see the ‘‘Mainte-nance’’ section earlier in this manual.

Department of Transportation (DOT) Qual-ity Grades: All passenger car tires mustconform to Federal Safety Requirements inaddition to these grades.

TreadwearTreadwear grade is a comparative ratingbased on tire wear rate when tested undercontrolled conditions on specified govern-ment test courses. For example, a tiregraded 150 would wear one and a half(1-1/2) times as well on the governmentcourse as a tire graded 100. However,relative tire performance depends on actualdriving conditions, and may vary signifi-cantly, due to variations in driving habits,service practices and differences in roadcharacteristics and climate.

Traction AA, A, B and CThe traction grades, from highest to lowest,are AA, A, B, and C. Those grades repre-sent the tire’s ability to stop on wet pave-ment as measured under controlled condi-tions, on specified government test surfacesof asphalt and concrete. A tire marked withC may have poor traction performance.

WARNINGThe traction grade assigned to yourvehicle tire’s is based on straight-ahead braking traction tests, and doesnot include acceleration, cornering, hy-droplaning, or peak traction character-istics.

Temperature A, B and CTemperature grades are A (the highest), B,and C. They represent a tire’s resistance toheat build-up, and its ability to dissipateheat when tested under controlled condi-tions on a specified indoor laboratory testwheel. Sustained high temperature cancause tire material to degenerate, reducingtire life. Excessive temperatures can lead tosudden tire failure. Grade C corresponds toa performance level which all passenger cartires must meet under the Federal MotorVehicle Safety Standard No. 109. Grades Aand B represent higher levels of perfor-mance on laboratory test wheels than theminimum required by law.

UNIFORM TIRE QUALITYGRADING

9-18

Z X

WARNINGThe temperature grade for this tire isestablished for a tire that is properlyinflated and not overloaded. Excessivespeed, under inflation, or excessiveloading, either separately or in combi-nation, can cause heat build-up andpossible tire failure.

Your NISSAN is covered by the followingemission warranties:

For USA1) Emission Defects Warranty

2) Emission Performance Warranty

For CanadaEmission Control System Warranty

Details of these warranties may be foundwith other vehicle warranties in your War-ranty Information and Maintenance LogBooklet that comes with your NISSAN. Ifyou did not receive a Warranty Informationand Maintenance Log Booklet, or it hasbecome lost, you may obtain a replacementby writing to:

● Nissan Motor Corporation USAConsumer Affairs DepartmentP.O. Box 191Gardena, CA 90248-0191

● Nissan Canada Inc.P.O. Box 1709Station ‘‘B’’Mississauga, Ontario,L4Y 4H6

If you believe that your vehicle has a defectwhich could cause a crash or could causeinjury or death, you should immediatelyinform the National Highway Traffic SafetyAdministration (NHTSA) in addition to no-tifying NISSAN.

If NHTSA receives similar complaints, itmay open an investigation, and if it findsthat a safety defect exists in a group ofvehicles, it may order a recall and remedycampaign. However, NHTSA cannot be-come involved in individual problems be-tween you, your dealer, or NISSAN.

To contact NHTSA, you may either call theAuto Safety Hotline toll-free at 1- 800-424-9393 (or 366-0123 in the Washington, D.C.area) or write to: NHTSA, U.S. Depart-ment of Transportation, Washington, D.C.20590. You can also obtain other informa-tion about motor vehicle safety from theHotline.

You may notify NISSAN by contacting ourConsumer Affairs Department, toll-free, at1-800-NISSAN-1.In Hawaii, call (808) 836-0888.

EMISSION CONTROLSYSTEM WARRANTY

REPORTING SAFETYDEFECTS (USA)

9-19

Z X

Due to legal requirements in some statesand Canadian Provinces, your vehicle maybe required to be in the ready condition foran Inspection/Maintenance (I/M) test of theemission control system.

The vehicle is set to the ready conditionwhen it is driven through certain drivingpatterns. Usually, the ready condition canbe obtained by ordinary usage of the ve-hicle.

If a powertrain system component is re-paired or the battery is disconnected, thevehicle may be reset to a not ready condi-tion. Before taking the I/M test, drive thevehicle through the following pattern to setthe vehicle to the ready condition. If youcannot or do not want to perform the drivingpattern, an authorized NISSAN dealer canconduct it for you.

WARNINGAlways drive the vehicle in a safe man-ner according to traffic conditions andobey all traffic laws.

1. Start the engine when the engine coolanttemperature gauge needle points to C.Allow the engine to idle until the gauge

needle points between the C and H (nor-mal operating temperature).

2. Accelerate the vehicle to 55 MPH (88km/h), then quickly release the accelera-tor pedal completely and keep it releasedfor at least 6 seconds.

3. Quickly depress the accelerator pedal fora moment, then drive the vehicle at aspeed of 53 to 60 MPH (86 to 96 km/h)for at least 5 minutes.

4.Stop the vehicle.

5.Accelerate the vehicle to 35 mph (55km/h) and keep the speed for 20 seconds.

6.Repeat steps 4 through 5 at least 3 times.

7.Accelerate the vehicle to 55 mph (88km/h) and keep the speed for at least 3minutes.

8. Stop the vehicle and turn the engine off.

9. Repeat steps 1 through 8 at least onemore time.

If step 1 through 7 are interrupted, repeatthe preceding step. Any safe driving modeis acceptable between steps. Do not stopthe engine until step 7 is completed.

READINESS FORINSPECTION/MAINTENANCE(I/M) TEST

9-20

Z X

A Genuine NISSAN Service Manual is the bestsource of service and repair information foryour vehicle. Filled with wiring diagrams, illus-trations and step-by-step diagnostic and ad-justment procedures, this manual is the sameone used by the factory trained techniciansworking at an authorized NISSAN dealership.Also available are Genuine NISSAN Owner’sManuals.For current pricing and availability of a Genu-ine NISSAN Service Manual or Genuine NIS-SAN Owner’s Manual, contact:

In the USA:See an authorized NISSAN dealer or contact:

Dyment Distribution Services20770 Westwood Dr.Strongsville OH 44136

In a hurry? Call 1-800-247-5321 and chargeyour purchase to Visa/Master Card.

In Canada:To purchase a copy of a Genuine NISSANService Manual or Owner’s Manual pleasecontact your nearest NISSAN Dealer. For thephone number and location of a NISSANDealer in your area call the NISSAN Satisfac-tion Center at 1-800-387-0122 and a bilingualNISSAN representative will assist you.Also available are Genuine NISSAN Serviceand Owner’s Manuals for older NISSAN mod-els.9-21

Z X

10 Index

A

After an accident........................................ 5-11Air bag (See supplemental restraintsystem) ...................................................... 2-42Air bag warning light.................................. 2-47Air cleaner housing filter............................ 7-13Air conditioner

Air conditioner operation ............... 3-20, 3-5Air conditioner service .......................... 3-14Air conditioner specification label ......... 9-11Air conditioner system refrigerant andlubrication recommendations.................. 9-6Heater and air conditioner (automatic)(if so equipped)..................................... 3-10Heater and air conditioner (manual)....... 3-3Rear seat heater and airconditioner ............................................ 3-13

Air flow charts .............................................. 3-7Alarm system (See theft warning) ............. 1-10Anchor point locations ............................... 2-69Antenna

Manual .................................................. 3-20Power.................................................... 3-20

Anti-lock brake system (ABS).................... 4-15Anti-lock brake warning light ....................... 1-8Armrests..................................................... 2-30

Ashtray (See cigarette lighter andashtray) ...................................................... 1-16Audio system

AM-FM radio with cassette player........ 3-14Compact disc (CD) player .................... 3-21

Autolamp switch......................................... 1-13Automatic

Automatic power window switch .......... 1-20Automatic transmission fluid (ATF) ........ 7-8Driving with automatic transmission....... 4-5

B

Battery........................................................ 7-11Before starting the engine ........................... 4-5Brake

Anti-lock brake system (ABS) .............. 4-15Brake booster ....................................... 7-17Brake fluid ..................................... 7-10, 9-2Brake light (See stop light) ................... 7-21Brake pedal .......................................... 7-16Brake system........................................ 4-14Brake warning light ................................. 1-7Brake wear indicators............................. 1-9Parking brake check............................. 7-16Parking brake operation ......................... 4-9Self-adjusting brakes ............................ 7-16

Break-in schedule ...................................... 4-12

Bulb check/instrument panel ....................... 1-6Bulb replacement....................................... 7-21

C

Capacities and recommended fuel/lubricants...................................................... 9-2Cargo net ................................................... 2-13Cargo (See vehicle loadinginformation) ................................................ 9-12Cassette player (See audio system) ......... 3-14CB radio or car phone ............................... 3-25Check engine indicator light(See malfunction indicator light) .................. 1-9Child restraint with top tether strap ........... 2-65Child restraints for infants and smallchildren ...................................................... 2-60Child safety sliding door lock....................... 2-4Cigarette lighter (accessory)and ashtray ................................................ 1-16Cleaning exterior and interior ...................... 6-2Clock .......................................................... 1-23Coin tray .................................................... 1-17Cold weather driving.................................. 4-16Compact disc (CD) player ......................... 3-21Controls

Audio controls....................................... 3-14Audio controls (rear) ............................. 3-24

Z X

Audio controls (steering wheel) ............ 3-23Heater and air conditioner controls(automatic)............................................ 3-10Heater and air conditioner controls(manual).................................................. 3-3Rear seat heater and air conditionercontrols ................................................. 3-13

CoolantCapacities and recommended fuel/lubricants ................................................ 9-2Changing engine coolant........................ 7-5Checking engine coolant level ............... 7-4Engine coolant temperature gauge ........ 1-4

Cornering light ........................................... 1-15Corrosion protection .................................... 6-4Cruise control............................................. 4-10Cup holder ................................................. 1-18

D

Daytime running light system(Canada only) ............................................ 1-13Defogger switch

Rear window defogger switch .............. 1-12Dimensions and weights.............................. 9-8Door ajar warning light ................................ 1-7Door locks.................................................... 2-2Drive belts.................................................. 7-12Driving

Cold weather driving............................. 4-16Driving with automatic transmission....... 4-5

Precautions when starting anddriving ..................................................... 4-2

E

Economy - fuel........................................... 4-12Emission control information label............. 9-10Emission control system warranty............. 9-19Engine

Before starting the engine ...................... 4-5Capacities and recommended fuel/lubricants ................................................ 9-2Changing engine coolant........................ 7-5Changing engine oil................................ 7-6Changing engine oil filter........................ 7-7Checking engine coolant level ............... 7-4Checking engine oil level ....................... 7-5Engine compartment checklocations.................................................. 7-3Engine coolant temperature gauge ........ 1-4Engine cooling system ........................... 7-4Engine oil ................................................ 7-5Engine oil and oil filterrecommendation ..................................... 9-4Engine oil pressure warning light ........... 1-6Engine oil viscosity ................................. 9-5Engine serial number ............................. 9-9Starting the engine ................................. 4-8

Exhaust gas (Carbon monoxide)................. 4-2

F

Five passenger seating ............................. 2-18Five passenger seating with cargoroom........................................................... 2-18Flashers (See hazard warning flasherswitch)........................................................ 1-15Flat tire......................................................... 5-2Flexible seating.......................................... 2-32Floor mat positioning........................ 2-17, 2-20Floor mat positioning aid ........................... 2-20Fluid

Automatic transmission fluid (ATF) ........ 7-8Brake fluid ..................................... 7-10, 9-2Capacities and recommended fuel/lubricants ................................................ 9-2Engine coolant........................................ 7-4Engine oil ................................................ 7-5Power steering fluid ........................ 7-9, 9-2Window washer fluid ............................ 7-10

F.M.V.S.S. certification label ..................... 9-10Fuel

Capacities and recommended fuel/lubricants ................................................ 9-2Fuel economy ....................................... 4-12Fuel filler lid and cap ............................ 2-15Fuel filler lid lock opener lever ............. 2-15Fuel gauge.............................................. 1-5Fuel octane rating................................... 9-3Fuel recommendation............................. 9-2

Fuses ......................................................... 7-17Fusible links ............................................... 7-18

10-2

Z X

G

GaugeEngine coolant temperature gauge ........ 1-4Fuel gauge.............................................. 1-5Odometer................................................ 1-4Speedometer .......................................... 1-4Tachometer............................................. 1-4Trip odometer ......................................... 1-4

General maintenance .................................. 8-2

H

Hazard warning flasher switch .................. 1-15Head restraints .......................................... 2-30Headlight control switch............................. 1-13Headlights .................................................. 7-19Heater

Heater and air conditioner (automatic)(if so equipped)..................................... 3-10Heater and air conditioner (manual)....... 3-3Rear seat heater and airconditioner ............................................ 3-13

Hood release ............................................. 2-10

I

Ignition switch .............................................. 4-4Important vehicle information label............ 9-10Increasing fuel economy............................ 4-12Indicator lights and chimes (See warning/

indicator lights and chimes)......................... 1-6Inertial fuel shut off switch......................... 5-11Inside mirror............................................... 2-80Instrument brightness control .................... 1-15Integrated child safety seats...................... 2-71Interior lights .............................................. 1-24

J

Jump starting...................................... 5-8, 7-12

K

Key............................................................... 2-2Keyless entry system (See multi-remotecontrol system) ............................................ 2-7

L

LabelsAir conditioner specification label ......... 9-11Emission control information label........ 9-10Engine serial number ............................. 9-9F.M.V.S.S. certification label ................ 9-10Vehicle identification number ................. 9-9Vehicle identification number (VIN)plate ........................................................ 9-9Warning labels (for SRS) ..................... 2-47

License plateInstalling the license plate .................... 9-11

LightAir bag warning light............................. 2-47Brake light (See stop light) ................... 7-21Bulb check/instrument panel .................. 1-6Bulb replacement.................................. 7-21Cornering light ...................................... 1-15Headlight control switch ....................... 1-13Headlights............................................. 7-19Interior lights ......................................... 1-24Light bulbs ............................................ 7-19Luggage compartment lights ................ 1-24Spotlights .............................................. 1-25Warning/indicator lights and chimes ...... 1-6

LockChild safety sliding door lock ................. 2-4Door locks............................................... 2-2Fuel filler lid lock opener lever ............. 2-15Power door lock...................................... 2-5Rear door lock ...................................... 2-11

Luggage compartment lights ..................... 1-24Luggage rack ............................................. 2-14Luggage (See vehicle loadinginformation ................................................. 9-12

M

MaintenanceGeneral maintenance ............................. 8-2Inside the vehicle.................................... 8-3Maintenance precautions ....................... 7-2Outside the vehicle................................. 8-2Periodic maintenance schedules............ 8-5

10-3

Z X

Seat belt maintenance.......................... 2-60Under the hood and vehicle ................... 8-4

Malfunction indicator light ............................ 1-9Manual antenna ......................................... 3-20Manual front seat adjustment .................... 2-26Manual rear windows................................. 1-22Map light (See spot light) .......................... 1-25Mirror

Inside mirror.......................................... 2-80Outside mirror control ........................... 2-79Outside mirrors ..................................... 2-80Vanity mirror ......................................... 2-80

Multi-remote control system ........................ 2-7

O

Odometer ..................................................... 1-4Oil

Capacities and recommended fuel/lubricants ................................................ 9-2Changing engine oil................................ 7-6Changing engine oil filter........................ 7-7Checking engine oil level ....................... 7-5Engine oil ................................................ 7-5Engine oil and oil filterrecommendation ..................................... 9-4Engine oil viscosity ................................. 9-5

Outside mirror control ................................ 2-79Outside mirrors .......................................... 2-80Overdrive switch .......................................... 4-7Overheat

If your vehicle overheats ...................... 5-10

Owner’s manual order form....................... 9-21

P

ParkingParking brake check............................. 7-16Parking brake operation ......................... 4-9Parking/parking on hills ........................ 4-13

Periodic maintenance schedules................. 8-5Personal reading light................................ 1-24Power

Power antenna ..................................... 3-20Power door lock...................................... 2-5Power rear windows ............................. 1-22Power steering fluid ........................ 7-9, 9-2Power support front seat ...................... 2-28Power windows..................................... 1-19

PrecautionsMaintenance precautions ....................... 7-2Precautions on seat belt usage............ 2-49Precautions when starting anddriving ..................................................... 4-2

Push starting.............................................. 5-10

R

RadioAM-FM radio with cassette player........ 3-14CB radio or car phone.......................... 3-25

Readiness for inspection maintenance (I/M)test ............................................................. 9-20

Rear door................................................... 2-11Rear door lock ........................................... 2-11Rear power point ....................................... 1-17Rear seat heater and air conditioner......... 3-13Rear window defogger switch ................... 1-12Rear window wiper and washerswitches ..................................................... 1-12Refrigerant recommendation ....................... 9-6Registering your vehicle in anothercountry ......................................................... 9-9Remote keyless entry system (Seemulti-remote control system) ....................... 2-7Removing and installing the second row benchseat ............................................................ 2-32Reporting safety defects (USA)................. 9-19

S

SafetyChild safety sliding door lock ................. 2-4Reporting safety defects (USA)............ 9-19

Seat belt2-point type without retractor................ 2-583-point type with retractor ........... 2-51, 2-53Precautions on seat belt usage............ 2-49Seat belt extenders .............................. 2-60Seat belt maintenance.......................... 2-60Seat belts.............................................. 2-49

Seat belt warning light ................................. 1-7Seat positions ............................................ 2-21Seating arrangements ............................... 2-15

10-4

Z X

SeatsFive passenger seating ........................ 2-18Five passenger seating with cargoroom...................................................... 2-18Flexible seating..................................... 2-32Integrated child safety seats ................ 2-71Manual front seat adjustment............... 2-26Power support front seat ...................... 2-28Seat positions ....................................... 2-21Second row bench seat........................ 2-21Second row bucket seats ..................... 2-24Seven passenger seating..................... 2-17Sliding three-passenger seat................ 2-38Three-passenger bench seat in fullyforward position .................................... 2-19Three-passenger bench seat in storageposition ................................................. 2-17

Seats/floor mats......................................... 2-15Self-adjusting brakes ................................. 7-16Service manual order form ........................ 9-21Seven passenger seating .......................... 2-17Shifting

Automatic transmission .......................... 4-6Sliding three-passenger seat..................... 2-38Spark plug replacement............................. 7-12Speedometer ............................................... 1-4Spotlights ................................................... 1-25SRS warning label ..................................... 2-47Starting

Before starting the engine ...................... 4-5Jump starting................................. 5-8, 7-12Precautions when starting and

driving ..................................................... 4-2Push starting......................................... 5-10Starting the engine ................................. 4-8

SteeringPower steering fluid ........................ 7-9, 9-2Tilting steering wheel............................ 2-78

Stop light.................................................... 7-21Storage

Coin tray ............................................... 1-17Compact disc storage........................... 1-18Under seat storage tray........................ 2-31

Sun shade.................................................. 1-21Sunroof ...................................................... 1-21Supplemental restraint system

Information and warning labels ............ 2-47Switch

Autolamp switch ................................... 1-13Automatic power window switch .......... 1-20Hazard warning flasher switch ............. 1-15Headlight control switch ....................... 1-13Ignition switch ......................................... 4-4Overdrive switch ..................................... 4-7Rear window defogger switch .............. 1-12Rear window wiper and washerswitches ................................................ 1-12Turn signal switch................................. 1-14Windshield wiper and washerswitch.................................................... 1-11

T

Tabletop seats ........................................... 2-31

Tachometer.................................................. 1-4Theft warning ............................................. 1-10Three way catalyst....................................... 4-2Three-passenger bench seat..................... 2-57Three-passenger bench seat in fullyforward position ......................................... 2-19Three-passenger bench seat in storageposition....................................................... 2-17Tilting steering wheel................................. 2-78Timing belt ................................................... 9-7Timing chain ................................................ 9-7Tire

Flat tire.................................................... 5-2Spare tire .............................................. 7-29Tire chains ............................................ 7-26Tire placard........................................... 9-11Tire pressure ........................................ 7-25Tire rotation .......................................... 7-27Tool kit .................................................... 5-2Types of tires........................................ 7-26Uniform tire quality grading .................. 9-18Wheels and tires ........................... 7-25, 9-8Wheel/tire size ........................................ 9-8

TowingTow truck towing .................................. 5-12Towing load/specification chart ............ 9-14Trailer towing ........................................ 9-13

TransmissionAutomatic transmission fluid (ATF) ........ 7-8Driving with automatic transmission....... 4-5

Travel (See registering your vehicle inanother country)........................................... 9-9

10-5

Z X

Trip odometer .............................................. 1-4Turn signal switch...................................... 1-14

U

Under seat storage tray............................. 2-31Uniform tire quality grading ....................... 9-18

V

Vanity mirror .............................................. 2-80Vehicle dimensions and weights ................. 9-8Vehicle identification .................................... 9-9Vehicle identification number....................... 9-9Vehicle identification number (VIN)plate ............................................................. 9-9Vehicle loading information ....................... 9-12Vehicle recovery ........................................ 5-14Ventilators .................................................... 3-2

W

WarningAir bag warning light............................. 2-47Hazard warning flasher switch ............. 1-15Theft warning........................................ 1-10Warning labels (for SRS) ..................... 2-47Warning/indicator lights and chimes ...... 1-6

Weights (See dimensions and weights) ...... 9-8Wheels and tires ................................ 7-25, 9-8Wheel/tire size ............................................. 9-8

When traveling or registering your vehiclein another country........................................ 9-9Window washer fluid.................................. 7-10Windows

Locking passengers’ windows.............. 1-20Manual rear windows ........................... 1-22Power rear windows ............................. 1-22Power windows..................................... 1-19

Windshield wiper and washer switch ........ 1-11Wiper

Rear window wiper and washerswitches ................................................ 1-12Windshield wiper and washerswitch.................................................... 1-11Wiper blades......................................... 7-14

10-6

Z X

Recommended fuel:Unleaded gasoline, at least 87 AKI number(RON 91).For further details such as gasohol, see‘‘Fuel recommendation’’ in the ‘‘Technicaland consumer information’’ section.

Recommended engine oil:● API SG or SH and Energy Conserving II● API Certification Mark● SAE 5W-30 viscosity oil is preferred for

all ambient temperaturesSee ‘‘Engine oil and oil filter recommenda-tion’’ in the ‘‘Technical and consumer infor-mation’’ section.

Cold tire pressure:See tire placard affixed to the glove com-partment lid.

Recommended new vehiclebreak-in procedure:During the first 1,000 miles (1,600 km) ofvehicle use, follow the recommendationsoutlined in the “Break-in schedule’’ informa-tion found in the “Starting and Driving” sec-tion of this Owner’s Manual. Follow theserecommendations for the future reliabilityand economy of your new vehicle. Failure tofollow these recommendations may result invehicle damage or shortened engine life.

AGS0501

GAS STATION INFORMATION QUICK REFERENCE

Z X

1997-Nissan-Quest

Documents

nissan warranties

world of nissan

nissan vehicles

nissan dealer

nissan affiliates

vehicle weight

nissan story of growth

vehicle maintenance