140283 07-08 Honda Civic SI Sedan Cat-back

BORLA PERFORMANCE INDUSTRIES 5901 Edison Dr.

Oxnard, Ca. 93033 805-986-8600

TITLE: 07-08 Honda Civic SI Installation Instructions

PART NO. A-35439 Page 1 of 4

Exhaust System Installation For 2007-2008 Honda Civic SI Sedan & Coupe

Thank you for purchasing a Borla Performance Cat-Back™ Exhaust System. Borla Performance Cat-Back™ Exhaust System (Part number 140283) has been designed for the 2007-2008 Honda Civic SI sedan equipped with a 2.0L 4 cylinder engine, front wheel and a manual transmission. Borla Performance Cat-Back™ Exhaust System (Part number 140284) has been designed for the 2007-2008 Honda Civic SI coupe equipped with a 2.0L 4 cylinder engine, front wheel and a manual transmission. Borla Performance Industries recommends that an exhaust shop or professional after market parts installer, who has all the necessary equipment, tools and experienced personnel needed for proper installation, should perform the installation of this system. However, if you decide to perform the installation, we recommend someone should help you. Ensure the installer uses all under car safety precautions including eye protection. Please take time to read and understand the following… By installing your Borla Performance Exhaust System, you indicate that you have read this document and you agree with the terms stated below. It is the responsibility of the purchaser to follow all installation instruction guidelines and safety procedures supplied with your Borla Performance Exhaust System Borla Performance Industries assumes no responsibility for damages occurring from misuse, abuse, improper installation, improper operation, lack of responsible care, or all previously stated reasons resulting from incompatibility with other manufacturer’s products and/or systems. Included with your Borla Performance Exhaust System is a warranty card. Please read it carefully before you begin any work on your vehicle. If you should have any questions regarding our warranty policy, installation, or any other matter pertaining to your new Borla Performance Exhaust System, please give us a call at the number provided on the warranty card.

Precision manufactured using high quality austenitic stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance Exhaust System on your vehicle will eliminate the restrictive design of the stock exhaust, allowing your engine to discharge exhaust gas easier. The result is more horsepower and torque, longer engine life, and a distinctive throaty growl- all this, with easy bolt-on installation. These installation instructions have been written to help you in the installation of your Borla Performance Exhaust System. Please read it completely before installing your system.

BORLA PERFORMANCE INDUSTRIES 5901 Edison Dr.

Oxnard, Ca. 93033 805-986-8600

TITLE: 07-08 Honda Civic SI Installation Instructions

PART NO. A-35439 Page 2 of 4

Minimum Required Tool List: TOOLS: 1 3/8” Drive Ratchet 2 3/8” Drive Extension 3” 3 14mm Socket 4 15mm Socket 5 Pry Bar SHOP SUPPLIES: 1 Spray Lubricant

Borla Performance Cat-Back™ Bill of Materials

1. Front pipe assembly 2. Front muffler assembly 3. Rear muffler assembly 4. 2.25” clamp (qty 2)

BORLA PERFORMANCE INDUSTRIES 5901 Edison Dr.

Oxnard, Ca. 93033 805-986-8600

TITLE: 07-08 Honda Civic SI Installation Instructions

PART NO. A-35439 Page 3 of 4

Caution!!! Never work on a hot exhaust system. Serious injury in the form of burns can result If the vehicle has been in use and the exhaust system is hot, allow vehicle to cool for at least 1 hour. Always wear eye protection when working under any vehicle. Note: It is our recommendation that you use a hoist or hydraulic lift to facilitate the installation of your new Borla Performance Cat-Back Exhaust System. Taking all under car safety precautions, lift the vehicle using a hoist or hydraulic lift. Once this has been done, you may begin the removal of your old exhaust system from your vehicle. Note: Before removing the original exhaust system from your vehicle, please compare the parts you have received with the bill of materials provided on the previous page to assure that you have all the parts necessary for the installation of your new Borla Performance Cat-Back Exhaust System.

Original Exhaust System Removal

Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and allowing a significant period of time for the chemical to lubricate the threads before attempting to disassemble. 1. Unbolt the flange located just in front of the rear muffler.

2. Lubricate all the hangers and rubber isolators.

3. Using a muffler stand or an additional person to hold the rear muffler into position, remove the hangers from the rubber isolators and remove the rear muffler from the vehicle as shown in figure 1.

4. Unbolt the flange located just behind the catalytic converter and save hardware for installation of your new Borla Exhaust System.

5. Using a muffler stand or an additional person to hold the front muffler assembly into position, remove the hangers from the rubber isolators and remove the front muffler from the vehicle as shown in figure 2.

Figure 1

Figure 2

Warning: Use extreme caution during installation. Torque all fasteners according to manufacturer’s torque values and tightening sequence. DO NOT use air impact tools to tighten fasteners on Borla Performance Exhaust Systems. Use of such tools may result in bent flanges or gasket contact areas leading to exhaust leaks.

BORLA PERFORMANCE INDUSTRIES 5901 Edison Dr.

Oxnard, Ca. 93033 805-986-8600

TITLE: 07-08 Honda Civic SI Installation Instructions

PART NO. A-35439 Page 4 of 4

Borla Performance Cat-Back Exhaust System Installation

1. Using the original hardware, place the front pipe assembly into

position as shown in figure 3 making sure hanger is installed into the rubber isolator. Hand tighten the hardware for now.

2. Place a clamp over the expanded end of the front muffler assembly and set it into position as shown in figure 4 making sure to install the hangers into the rubber isolators. Do Not tighten the clamp.

3. Place a clamp over the expanded end of rear muffler assembly and set it into position as shown in figure 5 making sure to install the hangers into the rubber isolators. Do Not tighten the clamp.

4. Check your exhaust system for proper clearance under the vehicle and also for tip alignment.

5. Once position has been determined to be correct, tighten the Accuseal™ clamp to 32-35 ft. lbs. making sure the clamps openings are not over any of the notches in the pipes. Tighten the flange hardware to 18-22 ft. lbs.

6. Before starting your vehicle, make sure to check all wires, hoses, brake lines, body parts and tires for safe clearance from the exhaust system.

7. Start vehicle and check for any leaks. If any leaks are found, determine cause (such as loose hardware or incorrectly positioned clamp) and repair as necessary.

Figure 4

Figure 5

Note: When you first start your vehicle after the installation of your new Borla Performance Exhaust System, there may be some smoke and fumes coming from the system. This is a protective oil based coating used in the manufacturing of mandrel bent performance exhaust tubing. This is not a problem and will disappear within a very short period of time after the exhaust has reached normal operating temperatures.

Figure 3