7/31/2019 1289865120426
1/15
Hoot : Instructions 1
Rob Ives www.robives.com
1 2
Thread the long tabs on the wings
through the semi-circular holes in the
body and glue the body tabs to the
wings. (1)
Fold in and glue the three darts on the
body. (2)
Roll round the body and glue it into
place. (3)
You will need a craft knife or other sharp knife, a pair of scissors, some glue
and a glue spreader.
The best type of glue to use is white school glue (PVA.)
Print out the parts sheets onto thin cardboard. If you want to save ink, or prefer
to colour in the model yourself, print out the mono pages. Photocopier card is
ideal. Notice that the parts pages are marked front and back. Print out a front
page, flip it over, then print the back onto the same sheet. Leave the ink to dry
completely before continuing.
Before cutting anything out, score along all the dotted lines and cut out any
holes with a craft knife. Both these jobs are easier to do on full sheets of card.
Dashed lines are hill folds, dotted lines are valley folds. Cut along the solid
lines. Grey areas show where to glue
Cut
out
Dashed lines are
hill folds
Dotted lines are
valley folds
Black or White lines
show where to cut.
Shaded areas show
where to glue.
7/31/2019 1289865120426
2/15
Hoot : Instructions 2
3 4
5 6
Glue the
head down to
the top of the
body. (4)
It is made
slightly too
big; once the
glue is dry
trim the part
to size with
your scissors.
Glue togetherthe beak parts.
(5)
Glue the beak
and eyes to the
body. (6)
Youll need two
coins about this
size. These will
act as weights
Wrap the coin holders round
the coins. (7)
Glue them to the inside front
and back of the body. (8)
Fold round and glue together the
legs and the push rod as shown
above. (9 - 10)
Glue the push rod end into the top of
the head. (11) Use the end of a pencil
or a chop stick to press down theflaps to help the glue dry.
Fit the legs into the body. Glue the
long tabs to the legs. (12)
7/31/2019 1289865120426
3/15
Hoot : Instructions 3
7 8
9
Glue the box top to the legs. (13)
Fold round the four flaps on the
outside(14)
Assemble the button as shown below
(15) and glue on the button top.(16-17)
Glue the button to the end of the
push rod. (18)
Fold round and glue down the tabs on
the box tabs to make a triangular
section. (19)
Glue together the two parts of the box
and complete it as shown. (20-21)
Complete the owl by gluing the box top to the
box. (22)Once the glue is dry make Hoot flap his wings
by pressing the button under the box.
7/31/2019 1289865120426
4/15
HOOT! Parts. Front 1
Push rod
Beak E
yes
Wings
Head
top
12
1
12
1
10
7/31/2019 1289865120426
5/15
10
11
11
11
11
18
18
55 6a6a
11
11
Parts. Back 1
7/31/2019 1289865120426
6/15
22
21
21
19
20
22
22
13
13
12 12
17
17
13 13
9.
22
21
21
19
20
(cc) Rob Ives www.robives.com
HOOT! Parts. Front 2
Box
Box
Legs
BoxTop
Button
Top
7/31/2019 1289865120426
7/15
22
19
21 21
20
22
19
21 21
20
22
22
18
18
9
.
Parts. Back 2
7/31/2019 1289865120426
8/15
4
4
4 4
4
222
6a
6b
8 7 8 7
14 14 14 14 15
1616
3
HOOT! Parts. Front 3
Push Button
Body
Coin Holder Coin Holder
7/31/2019 1289865120426
9/15
7 7
3
88
14 14 14 14
17 1715
Parts. Back 1
7/31/2019 1289865120426
10/15
HOOT! Parts. Front 1 (mono)
Push rod
Beak E
yes
Wings
Head
top
12
1
12
1
10
7/31/2019 1289865120426
11/15
10
11
11
11
11
18
18
55 6a6a
11
11
Parts. Back 1
7/31/2019 1289865120426
12/15
22
21
21
19
20
22
22
13
13
12 12
17
17
13 13
9.
22
21
21
19
20
(cc) Rob Ives www.robives.com
HOOT! Parts. Front 2 (mono)
Box
Box
Legs
BoxTop
Button
Top
7/31/2019 1289865120426
13/15
22
19
21 21
20
22
19
21 21
20
22
22
18
18
9
.
Parts. Back 2
7/31/2019 1289865120426
14/15
4
4
4 4
4
222
6a
6b
8 7 8 7
14 14 14 14 15
1616
3
HOOT! Parts. Front 3 (mono)
Push Button
Body
Coin Holder Coin Holder
7/31/2019 1289865120426
15/15
7 7
3
88
14 14 14 14
17 1715
Parts. Back 1