1/2 Elima-Matic Bolted Plastic E5 Service & Operating ... · enmdlCsmre013 1 • Model E5 Non-Metallic Bolted Explanation of Pump Nomenclature Model Pump Size Wetted Parts Non-Wetted

Ver

sa-M

atic

E5 Plastic Pumps• Polypropylene• PVDF

1/2" Elima-Matic Bolted Plasticwith Metallic and Non-Metallic Center Sections E5

VERSA-MATIC® • Warren Rupp, Inc. • A Unit of IDEX Corporation 800 North Main Street, Mansfield, OH 44902 USA • Phone: (419) 526-7296 • www.versamatic.com

© Copyright 2013 Warren Rupp, Inc. All rights reserved

1: P

UMP

SPEC

S2:

INST

AL &

OP

3: E

XP V

IEW

4: W

ARRA

NTY

Serv

ice

& O

per

ati

ng

Ma

nu

al

Orig

inal

Inst

ruct

ions

e5nmdlCsm-rev0513www.versamatic.com

IMPORTANT

Read the safety warnings and instructions in this manual before pump installation and start-up. Failure to comply with the recommendations stated in this manual could damage the pump and void factory warranty.

When used for toxic or aggressive fluids, the pump should always be flushed clean prior to disassembly.

Airborne particles and loud noise hazards. Wear eye and ear protection.

Before maintenance or repair, shut off the compressed air line, bleed the pressure, and disconnect the air line from the pump. Be certain that approved eye protection and protective clothing are worn at all times. Failure to follow these recommendations may result in serious injury or death.

To be fully groundable, the pumps must be ATEX Compliant. Refer to the nomenclature page for ordering information.

Optional 8 foot long (244 centimeters) Ground Strap is available for easy ground connection.

To reduce the risk of static electrical sparking, this pump must be grounded. Check the local electrical code for detailed grounding instruction and the type of equipment required.

Refer to nomenclature page for ordering information.

When the pump is used for materials that tend to settle out or solidify, the pump should be flushed after each use to prevent damage. In freezing temperatures the pump should be completely drained between uses.

Before pump operation, inspect all fasteners for loosening caused by gasket creep. Retighten loose fasteners to prevent leakage. Follow recommended torques stated in this manual.

CAUTION

WARNING

Nonmetallic pumps and plastic components are not UV stabilized. Ultraviolet radiation can damage these parts and negatively affect material properties. Do not expose to UV light for extended periods of time.

In the event of diaphragm rupture, pumped material may enter the air end of the pump, and be discharged into the atmosphere. If pumping a product that is hazardous or toxic, the air exhaust must be piped to an appropriate area for safe containment.

This pump is pressurized internally with air pressure during operation. Make certain that all fasteners are in good condition and are reinstalled properly during reassembly.

Take action to prevent static sparking. Fire or explosion can result, especially when handling flammable liquids. The pump, piping, valves, containers and other miscellaneous equipment must be properly grounded.

Safety Information

Grounding the Pump

WARNINGTake action to prevent static sparking. Fire or explosion can result, especially when handling flammable liquids. The pump, piping, valves, containers or other miscellaneous equipment must be grounded.

UNIVERSAL ALL AODD

e5nmdlCsm-rev0513www.versamatic.com

Table of Contents

SECTION 1: PumP SPECIfICaTIONS ................1 •Nomenclature •Performance •Materials •DimensionalDrawings

SECTION 2: INSTallaTION & OPEraTION ......5 •PrincipleofPumpOperation •TypicalInstallationGuide •Troubleshooting

SECTION 3: ExPlOdEd VIEw ...........................8 •CompositeDrawings •PartsList •MaterialsCode

SECTION 4: warraNTy & CErTIfICaTES ....10 •Warranty •ECDeclarationofConformity-Machinery

Universal*

1: P

UMP

SPEC

S2:

INST

AL &

OP

3: E

XP V

IEW

4: W

ARRA

NTY

e5nmdlCsm-rev05131 • Model E5 Non-Metallic Bolted www.versamatic.com

Explanation of Pump Nomenclature

Model Pump Size Wetted Parts Non-Wetted Parts Diaphragm MaterialE Elima-Matic 6 1/4" A Aluminum A Aluminum 1 NeopreneUUltra-Matic 8 3/8" C Cast Iron S Stainless Steel 2NitrileVV-Series 5 1/2" S Stainless Steel PPolypropylene 3 (FKM)FluorocarbonRE AirVantage 7 3/4" H Alloy C G Groundable Acetal 4EPDM 1 1" PPolypropylene ZPTFE-coatedAluminum 5PTFE 41-1/4"or1-1/2" K Kynar JNickel-platedAluminum 6Santoprene(XL) 2 2" G Groundable Acetal C Cast Iron 7 Hytrel 3 3" B Aluminum (screen mount) QEpoxy-CoatedAluminum 9 Geolast

Diaphragm Series Valve Ball Material Valve Seat/Valve Seat O-Ring Material Construction DesignR Rugged 1Neoprene 1 Neoprene 9 BoltedDDome 2 Nitrile 2Nitrile 0 ClampedXThermo-Matic 3(FKM)Fluorocarbon 3(FKM)FluorocarbonTTef-Matic(2-piece) 4EPDM 4EPDMBVersa-Tuff(1-piece) 5PTFE 5PTFEFFUSION(one-piece 6Santoprene(XL) 6Santoprene(XL)integrated plate) 7 Hytrel 7 Hytrel 8 Polyurethane 8Polyurethane 9 Geolast 9 Geolast A Acetal AAluminumw/PTFEO-Rings S Stainless Steel SStainlessSteelw/PTFEO-Rings CCarbonSteelw/PTFEO-Rings HAlloyCw/PTFEO-Rings TPTFEEncapsulatedSiliconeO-Rings

Your Serial #: (fill in from pump nameplate) _____________________________________

VERSA-MATIC® MODEL IDENTIFICATION CODES

X X X X X X X X X X - X X X

Model

Pump Size

Wetted Parts

Non-Wetted Parts

Diaphragm Material

Diaphragm Series

Valve Ball Material

Valve Seat Material/Valve Seat O-ring Material

Construction Design

Revision Level

Options (if applicable)

Model Pump Size Wetted Parts Non-Wetted Parts Diaphragm MaterialE Elima-Matic 6 1/4" A Aluminum A Aluminum 1 Neoprene U Ultra-Matic 8 3/8" C Cast Iron S Stainless Steel 2 Buna-N V V-Series 5 1/2" S Stainless Steel P Polypropylene 3 (FKM) Fluorocarbon 7 3/4" H Hastelloy C G Groundable Acetal 4 Nordel 1 1" P Polypropylene Z PTFE-coated Aluminum 5 PTFE 4 1-1/4" or 1-1/2" K Kynar J Nickel-plated Aluminum 6 XL 2 2" G Groundable Acetal C Cast Iron 7 Hytrel 3 3" B Aluminum (screen mount) Q Epoxy-Coated Aluminum 9 Geolast

Diaphragm Series Valve Ball Material Valve Seat/Valve Seat O-ring Material Construction DesignR Rugged 1 Neoprene 1 Neoprene 9 Bolted D Dome 2 Buna-N 2 Buna-N 0 Clamped X Thermo-Matic 3 (FKM) Fluorocarbon 3 (FKM) Fluorocarbon T Tef-Matic (2-piece) 4 Nordel 4 Nordel B Versa-Tuff (1-piece) 5 PTFE 5 PTFE F FUSION (one-piece 6 XL 6 XL integrated plate) 7 Hytrel 7 Hytrel 8 Polyurethane 8 Polyurethane 9 Geolast 9 Geolast A Acetal A Aluminum w/ PTFE O-rings S Stainless Steel S Stainless Steel w/ PTFE O-rings C Carbon Steel w/ PTFE O-rings H Hastelloy C w/ PTFE O-rings T PTFE Encapsulated Silicone O-rings

Model #:

__ __ __ __ __ __ __ __ __ __ __ __ __(fill in from pump nameplate)

Your Model #:

UNIVERSAL TO ALL VM

1: P

UMP

SPEC

S

e5nmdlCsm-rev0513Model E5 Non-Metallic Bolted • 2www.versamatic.com

materials

Material Profile: Operating Temperatures:Max. Min.

Conductive Acetal: Tough, impact resistant, ductile. Good abrasionresistanceandlowfrictionsurface.Generallyinert,withgoodchemicalresistanceexceptforstrongacidsandoxidizingagents.

190°F88°C

-20°F-29°C

EPDM:Showsverygoodwaterandchemicalresistance.Haspoor resistance to oils and solvents, but is fair in ketones and alcohols.

280°F138°C

-40°F-40°C

FKM:(Fluorocarbon)Showsgoodresistancetoawiderange of oils and sovents; especially all aliphatic, aromatic and halogenated hydrocarbons, acids, animal and vegetable oils. Hotwaterorhotaqueoussolutions(over70°F)willattackFKM.

350°F177°C

-40°F-40°C

Hytrel®: Good on acids, bases, amines and glycols at room temperatures only.

220°F104°C

-20°F-29°C

Neoprene: All purpose. Resistance to vegetable oils. Generally not affected by moderate chemicals, fats, greases and many oilsandsolvents.Generallyattackedbystrongoxidizingacids,ketones, esters and nitro hydrocarbons and chlorinated aromatic hydrocarbons.

200°F93°C

-10°F-23°C

Nitrile: Generalpurpose,oil-resistant.Showsgoodsolvent,oil,waterandhydraulicfluidresistance.ShouldnotbeusedwithhighlypolarsolventslikeacetoneandMEK,ozone,chlorinatedhydrocarbons and nitro hydrocarbons.

190°F88°C

-10°F-23°C

Nylon: 6/6Highstrengthandtoughnessoverawide temperaturerange.Moderatetogoodresistancetofuels,oilsand chemicals.

180°F82°C

32°F0°C

Polypropylene:Athermoplasticpolymer.Moderatetensileandflexstrength.Resistsstongacidsandalkali.Attackedbychlorine,fumingnitricacidandotherstrongoxidizingagents.

180°F82°C

32°F0°C

PVDF:(PolyvinylideneFluoride)Adurablefluoroplasticwithexcellentchemicalresistance.ExcellentforUVapplications.High tensile strength and impact resistance.

250°F121°C

0°F-18°C

Santoprene®:Injectionmoldedthermoplasticelastomerwithnofabriclayer.Longmechanicalflexlife.Excellentabrasionresistance.

275°F135°C

-40°F-40°C

UHMW PE: A thermoplastic that is highly resistant to a broad rangeofchemicals.Exhibitsoutstandingabrasionandimpactresistance,alongwithenvironmentalstress-crackingresistance.

180°F82°C

-35°F-37°C

Urethane:Showsgoodresistancetoabrasives.Haspoorresistance to most solvents and oils.

150°F66°C

32°F0°C

Virgin PTFE:(PFA/TFE)Chemicallyinert,virtuallyimpervious.VeryfewchemicalsareknowntochemicallyreactwithPTFE;moltenalkalimetals,turbulentliquidorgaseousfluorineandafewfluoro-chemicalssuchaschlorinetrifluorideoroxygendifluoridewhichreadilyliberatefreefluorineatelevated temperatures.

220°F104°C

-35°F-37°C

Maximum and Minimum Temperatures are the limits for which these materials can be operated. Temperatures coupled with pressure affect the longevity of diaphragm pump components. Maximum life should not be expected at the extreme limits of the temperature ranges.

Metals:Alloy C:EqualtoASTM494CW-12M-1specificationfornickelandnickelalloy.Stainless Steel: EqualtoorexceedingASTMspecificationA743CF-8Mforcorrosionresistant iron chromium, iron chromium nickel and nickel based alloy castings for general applicaitons. Commonly referred to as 316 Stainless Steel in the pump industry.

For specific applications, always consult the Chemical Resistance Chart.

CAUTION! Operating temperature limitations are as follows:

Ambient temperature range -20Cto+40CProcess temperature range -20Cto+80Cformodelsratedascategory1equipment -20cto+100Cformodelratedascategory2equipmentInaddition,theambienttemperaturerangeandtheprocesstemperaturerangedonotexceedtheoperatingtemperaturerangeoftheappliednon-metallicpartsaslistedinthemanualsofthepumps.

afTErmarKET ParTS

Pumper Parts is your single source for parts that fit Air-Operated Double Diaphragm (AODD) pumps

• Wilden®

• ARO®

• Yamada®

RIGHT PART, RIGHT NOW

designed to perform equal to or greater than original equipment manufacture.

Phone: (419) 526-7296info@pum perparts.comwww.pumperparts.com

Pumper Parts and its products are not affiliated with any of the original equipment manufacturers referenced herein. All original equipment manufacturers’ names, colors, pictures, descriptions and part numbers are used for identification purposes only. Pumper Parts® is a registered trade name of IDEX Corporation. All other trademarks, registered trademarks and product names are the property of their respective owners. Yamada® is a registered trademark of Yamada Corporation. ARO® is a registered trade name of Ingersoll-Rand Company. Wilden® is a registered trade name of Wilden Pump and Engineering Company, a Dover Resources Company.

MODEL SPECIFIC UNIVERSAL ALL AODD

1: P

UMP

SPEC

S


Performance

Meters Feet

Disc

harg

e Hea

d in

PSI

2 106

0

100 90 80 70 60 50 40 30 20 10 0

240 220 200 180 160 140 120 100 80 60 40 20 0

75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0

1284

40

0

5 10 15 20 25 30 35 45 50Capacity in Liters Per Minute

Capacity in U.S. Gallons Per Minute

Displacement Per Stroke, 0.022 Gal. (0.08 L)

48

12

2 AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI

SCFM M3/HR 2 3.4 4 6.8 8 13.6 12 20.4

Meters Feet

Disc

harg

e Hea

d in

PSI

2 106

0

100 90 80 70 60 50 40 30 20 10 0

240 220 200 180 160 140 120 100 80 60 40 20 0

75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0

1284

40

0

5 10 15 20 25 30 35 45 50Capacity in Liters Per Minute

Capacity in U.S. Gallons Per Minute

Displacement Per Stroke, 0.02 Gal. (0.075 L)

48

12

2 AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI

SCFM M3/HR 2 3.4 4 6.8 8 13.6 12 20.4

E5 1/2" Bolted PlasticRubber and TPE Fitted

Flow Rate Adjustableto........0-11gpm(53lpm)Port Size Suction...................1/2"NPT Discharge.................1/2"NPTAir Inlet....................3/8"NPTAir Exhaust................3/8"NPTSuction Lift Dry......................12'(3.6m) Wet......................30'(9.1m)Max Solid Size(Diameter). . . . . . . . . . . . . . . . .. . . . . . . . 1/16" (1.6 mm)Max Noise Level . . . . . . . . . . . . 86 dB(A)Shipping Weights Polypropylene...........8.5lbs(3.9kg) PVDF..................12lbs(5.4kg)

E5 1/2" Bolted PlasticPTFE Fitted

Flow Rate Adjustableto........0-10gpm(37.9lpm)Port Size Suction...................1/2"NPT Discharge.................1/2"NPTAir Inlet....................3/8"NPTAir Exhaust................3/8"NPTSuction Lift Dry......................10'(3m) Wet......................30'(9.1m)Max Solid Size(Diameter). . . . . . . . . . . . . . . . .. . . . . . . . 1/16" (1.6 mm)Max Noise Level . . . . . . . . . . . . 85 dB(A)Shipping Weights Polypropylene...........8.5lbs(3.9kg) PVDF..................12lbs(5.4kg)

NOTE: Performance based on the following: PTFE fitted pump, flooded suction, water at ambient conditions. The use of other materials and varying hydraulic conditions may result in deviations in excess of 5%.

NOTE: Performance based on the following: PTFE fitted pump, flooded suction, water at ambient conditions. The use of other materials and varying hydraulic conditions may result in deviations in excess of 5%.

1: P

UMP

SPEC

S


E5 Non-Metallic Bolted Dimensionsininches(mm dimensions in brackets). The dimensions on this drawing are for reference only. A certified drawing can be requested if physical dimensions are needed.

dimensional drawings

2.0351.56

8.43214.02

10.06255.52

11.70297.14

11.17283.72

1/2" NPTDISCHARGE PORT

1/2" NPTSUCTION PORT

4X RELOCATE ABLE PLUGS

3/8" NPTAIR INLET

1.1128.19

.4010.16

7.01178.16

6.25158.75

8.30210.90

6.75171.45

6.12155.45

5.30134.62

4.30109.22

4.00101.60

1.6140.97

R .163.96

9.30236.32

R.163.96

3/8" NPTAIR EXHAUST

BOTTOM VIEW

2.0351.56

8.43214.02

10.06255.52

11.70297.14

11.17283.72

1/2" NPTDISCHARGE PORT

1/2" NPTSUCTION PORT

4X RELOCATE ABLE PLUGS

3/8" NPTAIR INLET

1.1128.19

.4010.16

7.01178.16

6.25158.75

8.30210.90

6.75171.45

6.12155.45

5.30134.62

4.30109.22

4.00101.60

1.6140.97

R .163.96

9.30236.32

R.163.96

3/8" NPTAIR EXHAUST

BOTTOM VIEW

Model Specific

1: P

UMP

SPEC

S


Air Line

Discharged Fluid

DischargeStroke Suction

Stroke

PrimedFluid

Air-OperatedDoubleDiaphragm(AODD)pumpsarepoweredby compressed air, nitrogen or natural gas.

The main directional (air) control valve ① distributes compressedairtoanairchamber,exertinguniformpressureover the inner surface of the diaphragm ②. At the same time, theexhaustingair③ from behind the opposite diaphragm isdirectedthroughtheairvalveassembly(s)toanexhaust port ④.

As inner chamber pressure (P1)exceedsliquidchamberpressure (P2), the rod ⑤ connected diaphragms shift together creating discharge on one side and suction on the opposite side. The discharged and primed liquid’s directions arecontrolledbythecheckvalves(ballorflap)⑥ orientation.

The pump primes as a result of the suction stroke. The suctionstrokelowersthechamberpressure(P3) increasing the chamber volume. This results in a pressure differential necessary for atmospheric pressure (P4)topushthefluidthrough the suction piping and across the suction side check valveandintotheouterfluidchamber⑦.

Suction (side) stroking also initiates the reciprocating (shifting, stroking or cycling) action of the pump. The suction diaphragm’s movement is mechanically pulled through its stroke.Thediaphragm’sinnerplatemakescontactwithanactuator plunger aligned to shift the pilot signaling valve. Once actuated, the pilot valve sends a pressure signal to the opposite end of the main directional air valve, redirecting the compressed air to the opposite inner chamber.

Principle of Pump Operation

SAFE AIREXHAUSTDISPOSALAREA

PUMP INSTALLATION AREA

1" DIAMETER AIREXHAUST PIPING



MUFFLER

LIQUIDLEVEL

SUCTIONLINE

LIQUIDLEVEL

SUCTIONLINE

MUFFLER

MUFFLER

SUBMERGED ILLUSTRATION

Pumpcanbesubmergedifthepumpmaterialsofconstructionarecompatiblewiththeliquidbeingpumped.Theairexhaustmust be piped above the liquid level. When the pumped product sourceisatahigherlevelthanthepump(floodedsuctioncondition),pipetheexhausthigherthantheproductsourcetoprevent siphoning spills.

MODEL SPECIFIC

2: IN

STAL

& O

P


Installation And Start-Up Locatethepumpasclosetotheproductbeingpumpedaspossible.Keepthesuctionlinelengthandnumberoffittingstoaminimum.Donotreducethesuctionlinediameter.

Air Supply Connectthepumpairinlettoanairsupplywithsufficientcapacityandpressuretoachievedesiredperformance.Apressureregulatingvalveshouldbeinstalledtoinsureairsupplypressuredoesnotexceedrecommendedlimits.

Air Valve Lubrication The air distribution system is designed to operate WITHOUT lubrication. This is the standard mode of operation. If lubrication is desired, install an air line lubricator settodeliveronedropofSAE10non-detergentoilforevery20SCFM(9.4liters/sec.)ofairthepumpconsumes.ConsultthePerformanceCurvetodetermineairconsumption.

Air Line Moisture Waterinthecompressedairsupplymaycauseicingorfreezingoftheexhaustair,causingthepumptocycleerraticallyorstopoperating.Waterintheairsupplycanbereducedbyusingapoint-of-useairdryer.

Air Inlet And Priming Tostartthepump,slightlyopentheairshut-offvalve.Afterthepumpprimes,theairvalvecanbeopenedtoincreaseairflowasdesired.Ifopeningthevalveincreasescyclingrate,butdoesnotincreasetherateofflow,cavitationhasoccurred.Thevalveshouldbeclosedslightlytoobtainthemostefficientairflowtopumpflowratio.

Surge Suppressor

Shut-Off Valve

Pressure Gauge

Drain PortShut-OffValve

CheckValve

Air Inlet

Discharge

Unregulated AirSupply to Surge

Suppressor

Pipe Connection(Style Optional)

Flexible Connector

Flexible Connector

VacuumGauge

Suction

Shut-Off Valve

Drain Port Pipe Connection(Style Optional)

FlexibleConnector

Air Dryer

Filter RegulatorP/N: 020.V107.000

Note: Pipe weight should not be supported by pump connections.

Muffler(Optional Piped Exhaust)

recommended Installation Guide

Available Accessories: 1. Surge Suppressor 2. Filter/Regulator 3. Air Dryer

1

2

3

Note: Surge Suppressor and Pipingmustbesupportedaftertheflexibleconnection.

CAUTIONThe air exhaust should be piped to an area for safe disposition of the product being pumped, in the event of a diaphragm failure.

Principle of Pump Operation

SUBMERGED ILLUSTRATION

UNIVERSAL ALL AODD

2: IN

STAL

& O

P


Troubleshooting GuideSymptom: Potential Cause(s): Recommendation(s):Pump Cycles Once Deadhead(systempressuremeetsorexceedsair

supply pressure).Increasetheinletairpressuretothepump.Pumpisdesignedfor1:1pressureratioatzeroflow. (Doesnotapplytohighpressure2:1units).

Air valve or intermediate gaskets installed incorrectly. Installgasketswithholesproperlyaligned.Bent or missing actuator plunger. Remove pilot valve and inspect actuator plungers.

Pump Will Not Operate / Cycle

Pumpisoverlubricated. Setlubricatoronlowestpossiblesettingorremove.Unitsaredesignedforlubefreeoperation.Lackofair(linesize,PSI,CFM). Checktheairlinesizeandlength,compressorcapacity(HPvs.cfmrequired).Check air distribution system. Disassembleandinspectmainairdistributionvalve,pilotvalveandpilotvalveactuators.Dischargelineisblockedorcloggedmanifolds. Check for inadvertently closed discharge line valves. Clean discharge manifolds/piping.Deadhead(systempressuremeetsorexceedsairsupply pressure).

Increasetheinletairpressuretothepump.Pumpisdesignedfor1:1pressureratioatzeroflow. (Doesnotapplytohighpressure2:1units).

Blockedairexhaustmuffler. Removemufflerscreen,cleanorde-ice,andre-install.Pumpedfluidinairexhaustmuffler. Disassemblepumpchambers.Inspectfordiaphragmruptureorloosediaphragmplateassembly.Pumpchamberisblocked. Disassembleandinspectwettedchambers.Removeorflushanyobstructions.

Pump Cycles and Will Not Prime or No Flow

Cavitation on suction side. Check suction condition (move pump closer to product).Check valve obstructed. Valve ball(s) not seating properly or sticking.

Disassemblethewetendofthepumpandmanuallydislodgeobstructioninthecheckvalvepocket. Clean out around valve ball cage and valve seat area. Replace valve ball or valve seat if damaged. Use heavier valve ball material.

Valve ball(s) missing (pushed into chamber or manifold).

Wornvalveballorvalveseat.Wornfingersinvalveballcage(replacepart).CheckChemical Resistance Guide for compatibility.

Valve ball(s)/seat(s) damaged or attacked by product. Check Chemical Resistance Guide for compatibility.Checkvalveand/orseatiswornorneedsadjusting. Inspectcheckvalvesandseatsforwearandpropersetting.Replaceifnecessary.Suction line is blocked. Removeorflushobstruction.Checkandclearallsuctionscreensorstrainers.Excessivesuctionlift. Forliftsexceeding20’ofliquid,fillingthechamberswithliquidwillprimethepumpinmostcases.Suction side air leakage or air in product. Visuallyinspectallsuction-sidegasketsandpipeconnections.Pumpedfluidinairexhaustmuffler. Disassemblepumpchambers.Inspectfordiaphragmruptureorloosediaphragmplateassembly.

Pump Cycles Running Sluggish/Stalling, Flow Unsatisfactory

Over lubrication. Setlubricatoronlowestpossiblesettingorremove.Unitsaredesignedforlubefreeoperation.Icing. Removemufflerscreen,de-ice,andre-install.Installapointofuseairdrier.Clogged manifolds. CleanmanifoldstoallowproperairflowDeadhead(systempressuremeetsorexceedsairsupply pressure).


Cavitation on suction side. Check suction (move pump closer to product).Lackofair(linesize,PSI,CFM). Checktheairlinesize,length,compressorcapacity.Excessivesuctionlift. Forliftsexceeding20’ofliquid,fillingthechamberswithliquidwillprimethepumpinmostcases.Airsupplypressureorvolumeexceedssystemhd. Decreaseinletair(press.andvol.)tothepump.Pumpiscavitatingthefluidbyfastcycling.Undersizedsuctionline. Meetorexceedpumpconnections.Restrictiveorundersizedairline. Install a larger air line and connection. Suction side air leakage or air in product. Visuallyinspectallsuction-sidegasketsandpipeconnections.Suction line is blocked. Removeorflushobstruction.Checkandclearallsuctionscreensorstrainers.Pumpedfluidinairexhaustmuffler. Disassemblepumpchambers.Inspectfordiaphragmruptureorloosediaphragmplateassembly.Check valve obstructed. Disassemblethewetendofthepumpandmanuallydislodgeobstructioninthecheckvalvepocket.Checkvalveand/orseatiswornorneedsadjusting. Inspectcheckvalvesandseatsforwearandpropersetting.Replaceifnecessary.Entrainedairorvaporlockinchamber(s). Purgechambersthroughtappedchamberventplugs.Purgingthechambersofaircanbedangerous.

Product Leaking Through Exhaust

Diaphragmfailure,ordiaphragmplatesloose. Replace diaphragms, check for damage and ensure diaphragm plates are tight.Diaphragmstretchedaroundcenterholeorboltholes. Checkforexcessiveinletpressureorairpressure.ConsultChemicalResistanceChartforcompatibility

withproducts,cleaners,temperaturelimitationsandlubrication.Premature Diaphragm Failure

Cavitation. Enlargepipediameteronsuctionsideofpump.Excessivefloodedsuctionpressure. Movepumpclosertoproduct.Raisepump/placepumpontopoftanktoreduceinletpressure.

Install Back pressure device (Tech bulletin 41r). Add accumulation tank or pulsation dampener.Misapplication(chemical/physicalincompatibility). ConsultChemicalResistanceChartforcompatibilitywithproducts,cleaners,temperaturelimitations

and lubrication.Incorrectdiaphragmplatesorplatesonbackwards,installedincorrectlyorworn.

CheckOperatingManualtocheckforcorrectpartandinstallation.Ensureouterplateshavenotbeenworntoasharpedge.

Unbalanced Cycling Excessivesuctionlift. Forliftsexceeding20’ofliquid,fillingthechamberswithliquidwillprimethepumpinmostcases.Undersizedsuctionline. Meetorexceedpumpconnections.Pumpedfluidinairexhaustmuffler. Disassemblepumpchambers.Inspectfordiaphragmruptureorloosediaphragmplateassembly.Suction side air leakage or air in product. Visuallyinspectallsuction-sidegasketsandpipeconnections.Check valve obstructed. Disassemblethewetendofthepumpandmanuallydislodgeobstructioninthecheckvalvepocket.Checkvalveand/orseatiswornorneedsadjusting. Inspectcheckvalvesandseatsforwearandpropersetting.Replaceifnecessary.Entrainedairorvaporlockinchamber(s). Purgechambersthroughtappedchamberventplugs.

For additional troubleshooting tips contact After Sales Support at [email protected] or 419-524-8388

UNIVERSAL ALL AODD, EXCEPT FLAP

2: IN

STAL

& O

P


Troubleshooting GuideSymptom: Potential Cause(s): Recommendation(s):Pump Cycles Once Deadhead(systempressuremeetsorexceedsair

supply pressure).Increasetheinletairpressuretothepump.Pumpisdesignedfor1:1pressureratioatzeroflow. (Doesnotapplytohighpressure2:1units).

Air valve or intermediate gaskets installed incorrectly. Installgasketswithholesproperlyaligned.Bent or missing actuator plunger. Remove pilot valve and inspect actuator plungers.

Pump Will Not Operate / Cycle

Pumpisoverlubricated. Setlubricatoronlowestpossiblesettingorremove.Unitsaredesignedforlubefreeoperation.Lackofair(linesize,PSI,CFM). Checktheairlinesizeandlength,compressorcapacity(HPvs.cfmrequired).Check air distribution system. Disassembleandinspectmainairdistributionvalve,pilotvalveandpilotvalveactuators.Dischargelineisblockedorcloggedmanifolds. Check for inadvertently closed discharge line valves. Clean discharge manifolds/piping.Deadhead(systempressuremeetsorexceedsairsupply pressure).


Blockedairexhaustmuffler. Removemufflerscreen,cleanorde-ice,andre-install.Pumpedfluidinairexhaustmuffler. Disassemblepumpchambers.Inspectfordiaphragmruptureorloosediaphragmplateassembly.Pumpchamberisblocked. Disassembleandinspectwettedchambers.Removeorflushanyobstructions.

Pump Cycles and Will Not Prime or No Flow

Cavitation on suction side. Check suction condition (move pump closer to product).Check valve obstructed. Valve ball(s) not seating properly or sticking.

Disassemblethewetendofthepumpandmanuallydislodgeobstructioninthecheckvalvepocket. Clean out around valve ball cage and valve seat area. Replace valve ball or valve seat if damaged. Use heavier valve ball material.

Valve ball(s) missing (pushed into chamber or manifold).

Wornvalveballorvalveseat.Wornfingersinvalveballcage(replacepart).CheckChemical Resistance Guide for compatibility.

Valve ball(s)/seat(s) damaged or attacked by product. Check Chemical Resistance Guide for compatibility.Checkvalveand/orseatiswornorneedsadjusting. Inspectcheckvalvesandseatsforwearandpropersetting.Replaceifnecessary.Suction line is blocked. Removeorflushobstruction.Checkandclearallsuctionscreensorstrainers.Excessivesuctionlift. Forliftsexceeding20’ofliquid,fillingthechamberswithliquidwillprimethepumpinmostcases.Suction side air leakage or air in product. Visuallyinspectallsuction-sidegasketsandpipeconnections.Pumpedfluidinairexhaustmuffler. Disassemblepumpchambers.Inspectfordiaphragmruptureorloosediaphragmplateassembly.

Pump Cycles Running Sluggish/Stalling, Flow Unsatisfactory

Over lubrication. Setlubricatoronlowestpossiblesettingorremove.Unitsaredesignedforlubefreeoperation.Icing. Removemufflerscreen,de-ice,andre-install.Installapointofuseairdrier.Clogged manifolds. CleanmanifoldstoallowproperairflowDeadhead(systempressuremeetsorexceedsairsupply pressure).


Cavitation on suction side. Check suction (move pump closer to product).Lackofair(linesize,PSI,CFM). Checktheairlinesize,length,compressorcapacity.Excessivesuctionlift. Forliftsexceeding20’ofliquid,fillingthechamberswithliquidwillprimethepumpinmostcases.Airsupplypressureorvolumeexceedssystemhd. Decreaseinletair(press.andvol.)tothepump.Pumpiscavitatingthefluidbyfastcycling.Undersizedsuctionline. Meetorexceedpumpconnections.Restrictiveorundersizedairline. Install a larger air line and connection. Suction side air leakage or air in product. Visuallyinspectallsuction-sidegasketsandpipeconnections.Suction line is blocked. Removeorflushobstruction.Checkandclearallsuctionscreensorstrainers.Pumpedfluidinairexhaustmuffler. Disassemblepumpchambers.Inspectfordiaphragmruptureorloosediaphragmplateassembly.Check valve obstructed. Disassemblethewetendofthepumpandmanuallydislodgeobstructioninthecheckvalvepocket.Checkvalveand/orseatiswornorneedsadjusting. Inspectcheckvalvesandseatsforwearandpropersetting.Replaceifnecessary.Entrainedairorvaporlockinchamber(s). Purgechambersthroughtappedchamberventplugs.Purgingthechambersofaircanbedangerous.

Product Leaking Through Exhaust

Diaphragmfailure,ordiaphragmplatesloose. Replace diaphragms, check for damage and ensure diaphragm plates are tight.Diaphragmstretchedaroundcenterholeorboltholes. Checkforexcessiveinletpressureorairpressure.ConsultChemicalResistanceChartforcompatibility

withproducts,cleaners,temperaturelimitationsandlubrication.Premature Diaphragm Failure

Cavitation. Enlargepipediameteronsuctionsideofpump.Excessivefloodedsuctionpressure. Movepumpclosertoproduct.Raisepump/placepumpontopoftanktoreduceinletpressure.

Install Back pressure device (Tech bulletin 41r). Add accumulation tank or pulsation dampener.Misapplication(chemical/physicalincompatibility). ConsultChemicalResistanceChartforcompatibilitywithproducts,cleaners,temperaturelimitations

and lubrication.Incorrectdiaphragmplatesorplatesonbackwards,installedincorrectlyorworn.

CheckOperatingManualtocheckforcorrectpartandinstallation.Ensureouterplateshavenotbeenworntoasharpedge.

Unbalanced Cycling Excessivesuctionlift. Forliftsexceeding20’ofliquid,fillingthechamberswithliquidwillprimethepumpinmostcases.Undersizedsuctionline. Meetorexceedpumpconnections.Pumpedfluidinairexhaustmuffler. Disassemblepumpchambers.Inspectfordiaphragmruptureorloosediaphragmplateassembly.Suction side air leakage or air in product. Visuallyinspectallsuction-sidegasketsandpipeconnections.Check valve obstructed. Disassemblethewetendofthepumpandmanuallydislodgeobstructioninthecheckvalvepocket.Checkvalveand/orseatiswornorneedsadjusting. Inspectcheckvalvesandseatsforwearandpropersetting.Replaceifnecessary.Entrainedairorvaporlockinchamber(s). Purgechambersthroughtappedchamberventplugs.

1

2

3

4

5

6

7

8

910

11

12

1314

15

16

17

18

19

2021

22

24

25

26

28

29

30

31

3233

34

35

36

3738

38

31

31

39

39

SEAT CONFIGURATION FORPTFE FITTED PUMPS

DISCHARGE SUCTION

27

27

FUSION DIAPHRAGM ASSEMBLY

PTFE 2-PIECE DIAPHRAGM ASSEMBLY

22

21

22

23

25

24

21

Torque Setting:70 in-lbs.






1

2

3

4

5

6

7

8

910

11

12

1314

15

16

17

18

19

2021

22

24

25

26

28

29

30

31

3233

34

35

36

3738

38

31

31

39

39


DISCHARGE SUCTION

27

27



22

21

22

23

25

24

21







1

2

3

4

5

6

7

8

910

11

12

1314

15

16

17

18

19

2021

22

24

25

26

28

29

30

31

3233

34

35

36

3738

38

31

31

39

39


DISCHARGE SUCTION

27

27



22

21

22

23

25

24

21







Composite repair Parts drawing

General Model Specific

3: E

XP V

IEW


Composite repair Parts listAir Valve Assembly

Item # Qty. Description Part Number- 1 ValveBody(includesitems1-11) 031.V004.5521 1 Valve Body PE500A2 1 Valve Spool Assembly (Includes items 3&4) E500BUBASY3 1 LargeValveSpoolU-Cup P98-104A4 1 SmallValveSpoolU-Cup P98-104AUB5 1 EndCapAssembly(IncludesO-Ring) E500D6 1 ReducingEndCapAssembly(Includes560.0580.360

O-Rings) E500DUBASY7 2 Staple E500F8 1 CTAirDiverter 10-0759 1 AirDiverterPlate E500H

10 1 Air Valve Gasket 360.V003.36011 4 ValveMountingScrews S1004

Center Section AssemblyItem # Qty. Description Part Number

Polypropylene Aluminum12 1 Center Section E501A E501A-SC13 1 PilotSpoolASY(IncludesItem#14) 775.V003.00014 8 PilotSpoolO-Rings 560.023.36015 1 PilotValveSleeveASY(IncludesItem#16) 755.V003.00016 6 PilotValveSleeveO-Rings 560.033.36017 2 Shaft/PilotRetainer 670.V001.55418 4 RetainerScrew E501C19 1 Muffler VTM-3

Diaphragm Assembly / ElastomersItem # Qty. Description Part Number

TPE/RUBBER PTFE 2-Piece PTFE Fusion20 2 MainShaftO-Ring E502B21 1 MainShaft E502A22 2 Diaphragm "E505xx

(SeeBelowMaterialChart)" E505TF E505F23 2 Back-UpDiaphragm N/A E505N N/A24 2 InnerDiaphragmPlate V199C N/A25 2 OuterDiaphragmPlate PV199B,KV199B N/A26 4 ValveSeatO-Ring "E510xx

(SeeBelowMaterialChart)" E510TES27 4 ManifoldSeal N/A E510TFG28 4 Valve Ball "V111xx

(SeeBelowMaterialChart)" V111SS, V111TFWet End Assembly

Item # Qty. Description Part NumberPolypropylene Kynar

29 2 Water Chamber PE519 KE51930 16 Water Chamber Bolt SV187A31 16 Water Chamber Washer SV189C32 16 WaterChamberNut SV185B33 4 Valve Ball Cage PE522 KE52234 4 Valve Ball Seat PE521 KE52135 1 "DischargeManifoldAssembly

(IncludesPlugs)" PE520ASY KE520ASY

36 1 "SuctionManifoldAssembly (IncludesPlugs)" PE520FASY KE520FASY

37 4 ManifoldPlugs 618.058.552 P8NK38 8 ManifoldBolts SV189D31 8 ManifoldWasher SV189C39 8 ManifoldNut SV164D

Elastomer Material SpecificationsMaterial Diaphragm P/N Valve Ball P/N O-Ring P/NNeoprene E505N N/A N/ABunaNitrile E505BN V111BN E510BN

Viton E505VT V111VT E510VTNordel E505ND N/A E510TES

Santoprene E505XL V111TPEXL E510XLHytrel E505FG V111TPEFG E51TES

Geolast N/A V111G N/AAcetal N/A V111A N/A

Polyurathane N/A V111PU N/AStainless Steel N/A V111SS N/A

MODEL SPECIFIC

3: E

XP V

IEW


written warranty5 - yEar limited Product warranty

Quality System ISO9001 Certified • Environmental Management Systems ISO14001 Certified Versa-Matic warrants to the original end-use purchaser that no product sold by

Versa-Matic that bears a Versa-Matic brand shall fail under normal use and service due to a defect in materialor workmanship within five years from the date of shipment from Versa-Matic’s factory.

~ See complete warranty at http://www.versamatic.com/pdfs/VM%20Product%20Warranty.pdf ~

DATE: August 10, 2011FECHA: DATUM:DATA:DATO:PÄIVÄYS:

AUTHORIZED / APPROVED BY: Approuve par: Aprobado por: Genehmigt von: approvato da: Goedgekeurd door: Underskrift: Valtuutettuna: Bemyndiget av: Autorizado Por:

04/19/2012 REV 07 VMQR 044FM

This product complies with the following European Community Directives: Ce produit est conforme aux directives de la Communauté européenne suivantes: Este producto cumple con las siguientes Directrices de la Comunidad Europea: Dieses produkt erfüllt die folgenden Vorschriften der Europäischen Gemeinschaft: Questo prodotto è conforme alle seguenti direttive CEE: Dir produkt voldoet aan de volgende EG-richtlijnen: Denna produkt överensstämmer med följande EU direktiv: Versa-Matic, Inc., erklærer herved som fabrikant, at ovennævnte produkt er i overensstemmelse med bestemmelserne i Direkktive:Tämä tuote täyttää seuraavien EC Direktiivien vaatimukstet:Dette produkt oppfyller kravene til følgende EC Direktiver:Este produto está de acordo com as seguintes Directivas comunitárias:

MANUFACTURED BY:FABRIQUE PAR:FABRICADA POR:HERGESTELLT VON:FABBRICATO DA:VERVAARDIGD DOOR:TILLVERKAD AV:FABRIKANT:VALMISTAJA:PRODUSENT:FABRICANTE:

DECLARATION DE CONFORMITE • DECLARACION DE CONFORMIDAD • ERKLÄRUNG BEZÜGLICH EINHALTUNG DER VORSCHRIFTENDICHIARAZIONE DI CONFORMITÀ • CONFORMITEITSVERKLARING • DEKLARATION OM ÖVERENSSTÄMMELSE

EF-OVERENSSTEMMELSESERKLÆRING • VAATIMUSTENMUKAISUUSVAKUUTUS • SAMSVARSERKLÄRING DECLARAÇAO DE CONFORMIDADE

VERSA-MATIC®

Warren Rupp, Inc.A Unit of IDEX Corporation 800 North Main Street P.O. Box 1568 Mansfield, OH 44901-1568 USA

Tel: 419-526-7296Fax: 419-526-7289

This product has used the following harmonized standards to verify conformance: EN809:1998+A1:2009Ce materiel est fabriqué selon les normes harmonisées suivantes, afin d’ en garantir la conformité:

Este producto cumple con las siquientes directrices de la comunidad europa:Dieses produkt ist nach folgenden harmonisierten standards gefertigtworden, die übereinstimmung wird bestätigt:Questo prodotto ha utilizzato i seguenti standards per verificare la conformita´:De volgende geharmoniseerde normen werden gehanteerd om de conformiteit van dit produkt te garanderen: För denna produkt har följande harmoniserande standarder använts för att bekräfta överensstämmelse:Harmoniserede standarder, der er benyttet:Tässä tuotteessa on sovellettu seuraavia yhdenmukaistettuja standardeja:Dette produkt er produsert i overenstemmelse med fløgende harmoniserte standarder:Este produto utilizou os seguintes padrões harmonizados para varificar conformidade:

PUMP MODEL SERIES: E SERIES, V SERIES, VT SERIES, VSMA3, SPA15, RE SERIES AND U2 SERIES

Dave RoseberryEngineering Manager

DECLARATION OF CONFORMITY

2006/42/ECon Machinery, according

to Annex VIII

MODEL SPECIFIC

4: W

ARRA

NTY

1/2 Elima-Matic Bolted Plastic E5 Service & Operating ... · enmdlCsmre013 1 • Model E5 Non-Metallic Bolted Explanation of Pump Nomenclature Model Pump Size Wetted Parts Non-Wetted

Documents