RoHS Compliant Rev. A.5, 07/19/2013 1 Features RoHS compliant Support multi protocol from 9.9Gb/s to 11.3 Gb/s Compliant with SFP+ MSA, SFF 8431 Rev. 4.1 Compliant with SFF 8432 Rev.5.0 mechanical dimension Compliant with Digital diagnostic SFF-8472 Rev.11.0 Transmission distance of 40km over single mode fiber C-band DWDM EML laser transmitter LC duplex connector Hot pluggable 20 pin connector Single power supply voltage : +3.3V Low power dissipation Three optional operating temperature ranges : Option ST : 0°C to 70°C Option ET : -5°C to 85°C Option IT : -40°C to 85°C Applications SONET OC-192 IR-2 / SDH L-64.2b 10GBASE-ER 10G Fiber channel G.709 OUT-2 Description OE Solutions’ Small Form Factor Pluggable (SFP+) transceivers are compatible with the Small Form Factor Pluggable 20pin Multi- Source Agreement (MSA). The high performance cooled DWDM EML transmitter and high sensitivity PIN receiver provide superior performance for SONET/SDH and Ethernet applications up to 40km optical links. Enhanced Digital Diagnostics functions are available via the 2-wire serial bus specified in the SFF-8472 Rev. 11.0. The transmitter and receiver features ac-coupled differential data inputs and outputs, and an LVTTL for Tx disable input and Tx fault output. Software TX disable is also implemented. The receiver features differential ac-coupled data outputs and LVTTL for LOS (Loss of Signal) output. 10Gb/s DWDM SFP+ 40km Transceiver RDPX0SER
21
Embed
10Gb/s DWDM SFP+ 40km Transceiver RDPX0SER · Rev. A.2 5, 07/19/2013 RDPX0SER DWDM SFP+ Transceiver Product Specifications 1. Absolute Maximum Ratings Parameter Symbol Min. Typ. Max.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
RoHS Compliant
Rev. A.5, 07/19/2013 1
Features
RoHS compliant
Support multi protocol from 9.9Gb/s to 11.3 Gb/s
Compliant with SFP+ MSA, SFF 8431 Rev. 4.1
Compliant with SFF 8432 Rev.5.0 mechanical
dimension
Compliant with Digital diagnostic SFF-8472
Rev.11.0
Transmission distance of 40km over single mode
fiber
C-band DWDM EML laser transmitter
LC duplex connector
Hot pluggable 20 pin connector
Single power supply voltage : +3.3V
Low power dissipation
Three optional operating temperature ranges :
Option ST : 0°C to 70°C
Option ET : -5°C to 85°C
Option IT : -40°C to 85°C
Applications
SONET OC-192 IR-2 / SDH L-64.2b
10GBASE-ER
10G Fiber channel
G.709 OUT-2
Description
OE Solutions’ Small Form Factor Pluggable
(SFP+) transceivers are compatible with the
Small Form Factor Pluggable 20pin Multi-
Source Agreement (MSA). The high performance
cooled DWDM EML transmitter and high
sensitivity PIN receiver provide superior
performance for SONET/SDH and Ethernet
applications up to 40km optical links.
Enhanced Digital Diagnostics functions are
available via the 2-wire serial bus specified in the
Storage and TransportationTemperature Tst -40 - 85 °C 2
Storage and Transportation
Relative Humidity
5 - 95 % 2
Notes: 1. Measured on top side front center of SFP module 2. Non-condensing 3.There are three options of operating maximum temperature:
Option ST: standard temperature from 0oC to 70
oC,
Option ET: extended temperature from -5oC to 85
oC
Option IT: extended temperature from -40oC to 85
oC
2. General Operating Conditions
Parameter Symbol Min. Typ. Max. Unit Notes
Bit Rate B 9.9 10.3 11.3 Gb/s -
Maximum Transmission Distance Dmax 80 - - km -
Operating Voltage Vcc 3.14 - 3.46 V -
Power Supply Current ICC - - 550 mA ST
- - 725 mA ET, IT
Total Power Consumption - - 2.5 W -
ESD (High speed pins) - - 500 V 2
Notes : 1. Supplies TEC, Current draw depends on Temperature 2. Human body model per JEDEC JESD22-A114-B, compliant with INF-8077i Rev. 4.5 August 31, 2005
Notes: 1. Average power measured at output 2. Defined as Peak power – Steady-state power (in dBm) when Tx-dis is de-asserted or when the module is hot plugged with Tx_dis in low state (Tx enabled). 3. Full spectral width (RBW=0.1nm) measured 15dB down from the maximum of center wavelength peak under full modulation condition 4. Ratio of the average output power in the dominant longitudinal mode to the power in the most significant side mode peak under full modulation condition 5. Deviation related to the ITU standardized wavelength. The EOL value is met as soon as the output average power is above 10% of the steady-state power. 6. The jitter performance meets Telcodia GR-253-Core and ITU-T Recommendations G.783, G813, G825 and G82511 with ITU-T 0.172(04/2005) for the measurement methods and the measurement equipment. 7. -500 to 800ps/nm
Laser Safety: All transceivers in this datasheet are Class I Laser products per FDA/CDRH and IEC-60825 standards.
They must be operated under specified operating conditions.
4 LVTTL-I/O SDA 2 wire Serial Interface Data Line 3 4
5 LVTTL-I/O SCL 2 wire Serial Interface Clock 3 4
6 -
MOD_ABS Module Absent, connected to Tx GND or Rx GND in the module
3 5
7 LVTTL-I RS0 Rate Select 0, not used 3 6
8 LVTTL-O Rx LOS Receiver Loss of Signal Indication (In FC designated as Rx_LOS and in Ethernet designated as Signal Detect Bar
3 7
9 LVTTL-I RS1 Rate Select 1, not used 3 6
10 - Rx GND Receiver Ground 1 1
11 - Rx GND Receiver Ground 1 1
12 CML-O RD- Receiver Negative Data Out 3 -
13 CML-O RD+ Receiver Positive Data Out 3 -
14 - Rx GND Receiver Ground 1 1
15 - Vcc Rx Receiver Power, 3.3V±5% 2 -
16 - Vcc Tx Transmitter Power, 3.3V±5% 2 -
17 - Tx GND Transmitter Ground 1 1
18 CML-I TD+ Transmitter Positive Data In 3 -
19 CML-I TD- Transmitter Negative Data In 3 -
20 - Tx GND Transmitter Ground 1 1 *Plug Seq. : Pin engagement sequence during hot plugging Notes : 1. The module ground contacts, Tx GND abd Rx GND, shall be isolated frim the module case, that is, frame ground. 2. Tx Fault is an open collector/drain output that shall be pulled up with a 4.7k ~ 10k on the host board. Pull up voltage
between 2.0V and VccT + 0.5V. When high, output indicates a laser fault of some kind. When low, output indicates normal operation. The LD output is not turned off in case of Tx Fault
3. Tx Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the TRx with a 4.7k ~ 10k to VccT.
4. SDA and SCL should be pulled up with a 4.7k ~ 10k on the host board. The pull-up voltage shall be VccT. SCL is the clock line of 2-wire serial interface for serial ID. SDA is the data line of 2-wire serial interface for serial ID.
5. Mod_ABS is connected to Tx GND or Rx GND in the SFP+ module. The host may pull the contact up to Vcc on the host board with a resistor in the range 4.7 ~ 10k. Mod_ABS is asserted “high” when the SFP+ module is physically absent from a host slot. In the SFP MSA (INF-8074i) this contact has the same function but is called MOD_DEF0.
6. RS0 and RS1 are module input rate select contacts and are pulled low to Tx GND with a >30k resistor in the module. RS0 is an input hardware contact which optionally selects the optical receive data path rate coverage for an SFP+ module. RS1 is an input hardware contact which optionally selects the optical transmit path data rate coverage for the SFP+ module. These contacts can also be used for AS0 and AS1 if implementing SFF8079. RS1 is commonly connected to Tx GND or Rx GND in the classical SFP modules. The host needs to ensure that it will not be damaged if this contact is connected to Tx GND or Rx GND in the module. For logical definitions of RS0/RS1, see Section 2.5 of SFF-8431 Rev. 2.1.
7. LOS is an open collector output. Shall be pulled up with a 4.7k ~ 10k on host board. Pull up voltage between 2.0 and VccR+0.3. Logic 0 indicates normal operation.