Take Assessment - Module 3 Exam - CCNP Building Scalable Internetworks 1 Refer to the diagram and configuration. OSPF is configured over Frame Relay using neighbor statements under router ospf mode. Although all PVCs are active, RTB and RTC do not see all OSPF routes in their routing tables. What could be done to fix this problem? (Choose two.) The frame-relay map statements on all routers should include the broadcast keyword. The frame-relay map statements should be replaced with the frame-relay interface-dlci command. The priority value on the hub router should be set to 0. The priority value on the spoke routers should be set to 0. The ip ospf network non-broadcast command should be configured on each router. 1
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Take Assessment - Module 3 Exam - CCNP
Building Scalable Internetworks
1
Refer to the diagram and configuration. OSPF is configured over Frame Relay using neighbor statements under router ospf mode. Although all
PVCs are active, RTB and RTC do not see all OSPF routes in their routing tables. What could be done to fix this problem? (Choose two.)
The frame-relay map statements on all routers should include the broadcast keyword.
The frame-relay map statements should be replaced with the frame-relay interface-dlci command.
The priority value on the hub router should be set to 0.
The priority value on the spoke routers should be set to 0.
The ip ospf network non-broadcast command should be configured on each router.
Refer to the diagram. A virtual link must be created to provide a logical path from Area 100 to the backbone Area 0. Which group of commands should be added to the OSPF configuration on the routers?
RTA(config-router)# area 2 virtual-link 2.2.2.2RTB(config-router)# area 2 virtual-link 3.3.3.3
RTC(config-router)# area 100 virtual-link 2.2.2.2RTB(config-router)# area 2 virtual-link 1.1.1.1
RTA(config-router)# area 0 virtual-link 2.2.2.2RTC(config-router)# area 100 virtual-link 2.2.2.2
RTA(config-router)# area 2 virtual-link 3.3.3.3RTC(config-router)# area 2 virtual-link 1.1.1.1
Refer to the exhibit. R1 redistributes RIP routes into the OSPF domain. The 10.10.10.0/24 network appears in the routing table of R2, but it does not appear in the routing table of R3. However, the show ip ospf database external output of R3 shows that the 10.10.10.0/24 network is in the R3 external OSPF database. What should be done to make sure that the 10.10.10.0/24 network appears in the R3 routing table?
11 Which command set would configure OSPF to assign networks to the backbone area and run only on networks, 192.168.4.0, 192.168.5.0, 192.168.6.0, and 192.168.7.0?
router ospf 0network 192.168.4.0 0.0.7.255 area 1
router ospf 65535network 192.168.4.0 0.0.3.255 area 0
router ospf 1network 192.168.4.0 0.0.255.255 area 1
router ospf 65535network 192.168.4.0 0.0.15.255 area 0
Observe the debug ip ospf events output from RTB. RTA and RTB cannot establish a neighbour relationship. Which configuration error could be the cause of this problem?
The Ethernet0 interface on RTB is configured with the wrong IP address.
The Ethernet0 interface on RTB is configured for a different OSPF routing process.
The Ethernet0 interface on RTB is configured with the wrong OSPF network type.
The Ethernet0 interface on RTB is configured with the wrong OSPF area.
Routing protocols OSPF and RIP are configured as shown in the exhibit. Router R3 is configured with a two-way redistribution between the OSPF and RIP domains. The show ip route output taken on routers R1 and R2 reveals that R2 has all external routes in its routing table. However, R1 has only inter-area routes. What does this indicate?
The subnets keyword is missing from the redistribution configuration on router R3.
The distribute-list out command configured on the Serial 0/1 interface of router R3 is blocking the routes.
The routes redistributed from RIP are defined with metric of 15.
A network administrator is troubleshooting a recent OSPF stub configuration between R3 and R4. The only routes that should appear on the routing table for R4 are intra-area routes, the default route, and interarea routes. Given the above configuration, what is the problem?
R4 is configured with the wrong OSPF process ID.
Network 192.168.15.0 should be configured under area 0.
Network 192.168.15.0 is configured using an incorrect wildcard mask.
R4 must be configured with the area 2 stub command.