1 VFD-M Sorozat 1. FEJEZET – ÁTVÉTEL VIZSGÁLAT Ezek a VFD-M típusú frekvenciaváltók kiszállítás előtt szigorú teszteken és különböző ellenőrzéseken mennek keresztül. Kérlek azért te is ellenőrizd le a következő dolgokat: Átvétel Ellenőrizd, hogy a csomag tartalmazza-e a következőket: Inverter, Felhasználói kézikönyv. Ellenőrizd, hogy az áru nem sérült-e meg a szállítás ideje alatt. Ellenőrizd, hogy az adattáblának megfelelő típusú terméket rendeltél. 1.1 Adattábla információ: Példa: 1HP 230V inverter 1.2 Típus meghatározás: 1-1
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1
VFD-M Sorozat
1. FEJEZET – ÁTVÉTEL VIZSGÁLATEzek a VFD-M típusú frekvenciaváltók kiszállítás előtt szigorú teszteken és különböző ellenőrzéseken mennek keresztül. Kérlek azért te is ellenőrizd le a következő dolgokat:
Átvétel
Ellenőrizd, hogy a csomag tartalmazza-e a következőket: Inverter, Felhasználói kézikönyv.
Ellenőrizd, hogy az áru nem sérült-e meg a szállítás ideje alatt.
Ellenőrizd, hogy az adattáblának megfelelő típusú terméket rendeltél.
Amennyiben az adattábla információja nem egyezik a te általad választott típuséval, akkor azt jelezd azonnal a kereskedőnél.
1
VFD-M Sorozat
1.4 KÜLSŐ ALKATRÉSZEK ÉS JELZÉSEK:
1-3
VFD-M Sorozat
1-4
2
VFD-M Sorozat
2. FEJEZET – RAKTÁROZÁS ÉS BEÉPÍTÉS
2.1 Raktározás
Az invertert tartsd a zárt eredeti dobozában a felszerelés idejéig. A teljes idejű garancia megtartása érdekében az alábbi leírásoknak megfelelően tárold, amennyiben hosszabb ideig nem kerül beszerelésre:
Tárold tiszta száraz helyen. Ne tedd ki direkt napsugárzásnak.
-20 °C - +60 °C Közötti hőmérsékleten raktározd.
0% - 90% páratartalmú páralecsapódás-mentes helyen raktározd.
86 kPA - 106kPA közötti nyomású helyen raktározd..
Szennyeződési osztály 2: - gyári felhasználásra megfelelő.
2-1
VFD-M Sorozat
2.3 Beépítés:A nem megfelelő inverter beépítés nagyban csökkentheti az inverter élettartamát. Figyelmesen vedd szemügyre a beépítés helyet, hogy az alábbi követelményeknek 100% -ig megfeleljen. A rossz helyválasztás akár a garancia megvonását is okozhatja!!
Ne szereld fel az invertert fűtőberendezés közelébe vagy direkt napsütötte helyre.
Ne építsd be az invertert, olyan helyre, ahol nagy a külső hőmérséklet, a páratartalom, a rezgés vagy a korrózív gáztartalom.
Függőleges helyzetben építsd be a frekvenciaváltót. Ne takard el semmivel a hűtőlevegő áramát.
Az inverter hőt termel. Hagyj elég helyet a frekvenciaváltó körül a hő eltávozásához, ahogy azt az alábbi ábra is mutatja:
Várjon 5 percet, mielőtt elkezdené a szerelést, hogy a DC Busz kondenzátora kisüljön.
A képviselet előzetes írásos engedélye nélkül bármilyen elektromos vagy mechanikus szerkezeti változtatás a frekvenciaváltón a garancia azonnali megszűnését jelenti.
Rövidzárlati ellenálló képesség:A bekötéshez olyan kábelt használj, ami képes legalább az 5,000 rms szimmetrikus amper átvitelére. A 460 V –os modelleknél a max. 480 V és a 230 V –os modelleknél max. 240V lehetséges.
Általános bekötési információ
Alkalmazott kódok
Minden VFD-M inverter megfelel a Underwriters Laboratories, Inc. (UL) és a kanadai Canadian Underwriters Laboratories (cUL) előírásainak, és ebből adódóan szintén megfelel a National Electrical Code (NEC) és a Canadian Electrical Code (CEC) szabványoknak is.
Ahhoz, hogy a bekötés szintén megfeleljen a UL és a cUL követelményeinek, kérlek kövesd az ebben a fejezetben lévő utasításokat. Kérlek a bekötésnél, vedd figyelembe az inverter oldalán lévő specifikus adatoknak megfelelő bekötési értékeket is.
A vonali biztosíték specifikációnál a “B” részben javasolt az előírt biztosíték használat (az U.L. szabvány ezt megköveteli).
Alkatrész MagyarázatHálózati áram Kérlek, olvasd el figyelmesen az A
– mellékletet a hálózati követelményekkel kapcsolatban.
Kismegszakító Bekapcsoláskor nagy felfutó áram keletkezhet. Kérlek, olvasd el a B – mellékletet a megfelelő biztosíték kiválasztása érdekében. A kismegszakító opcionális.
Mágnes- kapcsoló
(Opcionális)
Kérjük, ne használja a mágneses kapcsolót mint az inverter ki- be- kapcsolója, ez csökkenti az inverter működési élettartamát.
Hálózati fojtó
(Opcionális)
A hálózati tényező növeléséhez ajánlott. 1000kVA felett erősen javasolt a használata. Fontos, hogy az egység ne legyen messzebb, mint 10m az invertertől .
zavarszűrő(Opcionális)
Az elektromágneses interferencia csökkentéséhez szükséges.
Fék ellenállás(Opcionális)
A motor megállási idejének csökkentéséhez használatos. Kérjük lépjen kapcsolatba a területi képviselőjével a megfelelő típus kiválasztása miatt.
Megjegyzés: Kérlek, nézd meg a B mellékletet a helyes kismegszakító kiválasztásához.
Megjegyzés: Használj árnyékolt csavart érpárú vezetékeket a vezérlő kábeleknek. Fontos, hogy minden kábel jól elkülönüljön egymástól. A földelési kábelt csak a frekvenciaváltóhoz kösd. Ne kösd a földet mindkét a kábel mindkét végéhez.
3.5 Bekötési megjegyzések: Kérlek, olvasd el figyelmesen a bekötés előtt.
1. ! Veszély: Ne kössd a hálózati kábelt az inverter U/T1, V/T2, W/T3 kapcsaira, mert ez
károsodást okozhat a berendezésben.
2. ! Figyelem: Ellenőrizd, hogy minden csavar meg van húzva az előírt nyomatékkal.
3. A bekötés alatt tarts be a helyi szabványnak megfelelő szerelési utasítást a balesetek elkerülése céljából.
4. Ellenőrizd, hogy minden védelmi eszköz (megszakító vagy biztosíték) megfelelően van bekötve az inverter és a hálózati csatlakozás között.
5. Győződjön meg róla, hogy a kábelek jól csatlakoznak, és hogy az inverter megfelelően le van földelve.
6. Használjon a szabványnak megfelelő földelő kábelt a lehető legrövidebb hosszban.
7. Több inverter is berakható egy helyre. Ebben az esetben mindegyiket le kell külön földelni a fő földelő vezetékhez. A földelési kábeleket lehet párhuzamosan is kötni, mint azt az ábra is mutatja. Ellenőrizd, hogy a földelési kábelekben ne legyen hurokkötés!!
8. Ha az inverter kimenő kapcsai U/T1, V/T2, és W/T3 a motor csatlakozási pontokra U, V, és W, sorrendbe lettek bekötve, akkor a motor óra járásával ellentétesen fog forogni (a motor tengelyoldaláról nézve), ha az előre forgási parancs van kiadva. Az ellentétes forgási irány beállításához, cseréld meg bármelyik két motorkábel vezetéket.
9. Ellenőrizd, hogy a hálózati áramforrás képes legyen a megfelelő nagyságú feszültség és áramerősség szolgáltatására.
10. Ne köss be, és ne távolíts el vezetéket a frekvenciaváltóból, ha az áram alatt van.
11. Ne vizsgáld az alkatrészeket, ha a belső “CHARGE” lámpa világít, szüntesd meg a
hálózati áramot.
12. Ne mérd a jeleket az inverter áramkörén, ha az működik.
13. Az egyfázisú frekvenciaváltók esetén, a hálózati kábelt bemeneti három csatlakozási pont közül bármelyik két pontra kötheted R/L1, S/L2, T/L3.
Megjegyzés: Ez a frekvenciaváltó nem használható 1 fázisú motorok üzemeltetéséhez.
14. Vezesd a vezérlő és hálózati kábeleket külön csatornába. Ne keresztezd őket 90 fokban.
15. Ha EMI zavarszűrő szükséges az esetleges interferenciacsökkentésre, akkor azt kösd be a lehető legközelebb a frekvenciaváltóhoz. Az elektromágneses interferencia a vivő frekvencia csökkentésével is lehetséges.
16. Ha az inverter beépítési helyzetéhez közel fojtótekercs is beépítésre kerül, úgy kérjük, hogy a Zavarszűrőt a lehető legközelebb helyezze el a U/T1, V/T2, W/T3 terminálokhoz.
17. Ha külső földelés megszakadás elleni védelmet használ, akkor az áramerősséget az érzékelőn 200mA állítsd, és a felismerés érzékenysége ne legyen kevesebb, mint 0.1 másodperc a nem valós hibajelzések elkerülése érdekében.
1. Kérjük, vegye figyelembe, hogyha hagyományos motort működtet frekvenciaváltóval akkor az energiaveszteség nagyobb lesz mintha inverteres használatra készült motort használna.
2. Kerülje a meghajtott motoroknál a túl alacsony sebességet. Ebben az esetben a motor tengelyén lévő ventilátor nem tud elégséges levegőt szállítani a hűtéshez és így a berendezés károsodása, léphet fel.
3. A terhelést csökkenteni kell a motoron, ha a motor alacsony sebességen működik.
4. FEJEZET DIGITÁLIS VEZÉRLŐ MŰKÖDTETÉSÉ4.1 A digitális vezérlő leírása
A digitális vezérlő két részből áll: Kijelző panel és vezérlő gombok. A kijelző panel a frekvenciaváltó működési és beállítási paraméterek, megjelenítését szolgálja. A vezérlő gombok pedig a paraméterek és kijelzendő adatok változtatását szolgálják.
A “mode” gomb megnyomásával váltani tud a kijelzőn megjelenítendő aktuális értékek típusai között : frekvencia, áramerősség, referencia érték stb.
ENTER Enter
Az “ENTER” megnyomásával az inverter elmenti a kijelzőn kiírt paraméter értékeket.
RUN Run
Az inverter indítására szolgál. Ennek a gombnak nincs jelentősége ha külső vezérlőről egységről vezérelik a frekvenciaváltót.
STOPRESET
Stop / Reset
A frekvenciaváltó programjának megállítására szolgál. Ha az inverter hiba miatt állt le, akkor először keresse meg a hibát, majd ezzel a gombbal tudja a hiba után ismételt alapbeállításba hozni a berendezést.
Fel / Le
A fel és le gombok használatával lehet a kijelzett paraméter értékét változtatni. Továbbá használható még a különböző működési értékek vagy paraméterek közötti lépetésre. Megnyomva a fel vagy le gombot növelhetjük vagy csökkenthetjük a megváltoztatni kívánt mértékegységeket. A gyorsabb haladás érdekébe tartsd lenyomva a gombot.
Az aktuális jelenlegi frekvencia kijelzése. Ami az U, V, és W kimeneteken megjelenik. Ügyfél által beírt mértékegység (v), hol v = H x Pr.-65.
Számolási érték (c).
Az U, V, és W kimeneti pontokon mért áramerősség
A belső PLC által végrehajtott aktuális lépés száma
Beállított paraméter
Az aktuális érték elmentése a kiválasztott funkciónál.
Az inverter forgási irányát mutatja – ELŐRE
Az inverter forgási irányát mutatja - HÁTRA
“End” Felirat megjelenése jelzi, hogy az inverter elfogadta a bevitt parmétert. Amikor az új adat bevitelre került a gép automatikusan azt tárolja a memóriájába. A beállítandó érték módosításához
: Az ilyen szimbólummal jelölt paraméterek menetközben is állíthatók.
Pr.00 A frekvencia vezérlés forrása Alaphelyzet: 00Beállítás 00 A frekvencia a digitalis vezérlővel szabályozható. (LC-M02E)
01 A frekvencia a beépített potencióméterrel szabályozható. (LC-M02E) 02 A frekvencia 0 / +10 V bemeneten kersztül vezérelhető 03 A frekvencia 4 / 20mA bemenet keresztül vezérelhető 04 A frekvencia az RS-485 –ös kommunikációs interfészen kersztül
vezérelhető
Pr.01 A vezélési utasitás forrása Alaphelyzet: 00Beállítás 00 Parancs kiadása a digitalis vezérlőn keresztül.
01 Parancs kiadása külső vezérlőn keresztül. A digitalis panel STOP gombja aktív.
02 Parancs kiadása külső vezérlőn keresztül. A digitalis panel STOP gombja inaktív.
03 Parancs kiadása az RS – 485 –ös interfészen keresztül. A digitális panel STOP gombja aktív.
04 Parancs kiadása az RS – 485 –ös interfészen keresztül. A digitális panel STOP gombja inaktív.
Ez a parameter a motor megállítására vonatkozik, mikor az inverter érvényes STOP utasítást kap.
1. Sebességcsökkentéssel: A motor lassít a minimum kimenő frekvenciára (Pr.08) és megáll az előre meghatározott Pr.11 vagy Pr13. lassítási idő szerint.
2. Szabad kifutással: A motor a leállási utasítást követően szabadon forog a teljes megállásig.
5-1
VFD-M Sorozat
Hz
Freq.
MotorSpeed
Stops according to deceleration time
Time
Hz
Freq.
MotorSpeed
Free runningto stop
Time
Operationcommand ON ONOFF OFF
Ramp Coast
Megjegyzés: A motor megállítási módját rendszerint az alkamazás módja vagy a rendszer követelmények határozzák meg.
Ez a parméter az inverter maximális kimenő frekvenciaáját határozza meg. Minden analog bemenet (0 - +10V, 4 - 20mA) ennek a fügvényébe lesz skálázva a működési tartomány.
Ezt az értéke a motor adatáblájának megfelelően kell beállítani. A maximális feszültség frekvencia a Volt / Herz arányból határozható meg.
Például: Ha a névleges feszültség 460VAC és a maximális feszültség frekvencia 60 Hz –re van állítva, akkor a frekvenciaváltó egy állandó 7.66 –os aránnyal fog dolgozni. A beállított értéknek egyenlőnek vagy nagyobbnak kell lennie, mint a Középponti frekvencia érték. (Pr.06).
Pr.05 Maximális kimenő feszültség (Vmax)Beállítás 230V sorozat 0.1 - 255.0V Alaphelyzet: 220.0
Ez a parameter a Maximális kimenő feszültséget határozza meg az inverternél. A maximális kimenő feszültség paraméternek kisebbnek vagy egyenlőnek kell lennie a névleges feszültséghez képest ami a motor adapttábláján szerepel. TA beállított értéknek egyenlőnek vagy nagyobbnak kell lennie, mint a Középponti feszültség (Pr.07).
Pr.06 Középponti frekvencia Alaphelyzet: 1.50
Beállítás 0.10 to 400.0Hz Egység: 0.1Hz
Ez a parameter határozza meg a Középponti feszültségét a V/F görbének. Ezzel a beállítással a V/F arány változtatható a minimum- és a középponti- frekvencia tartományban. Ennek az értéknek egyenlőnek vagy nagyobbnak kell lennie, mint a minimum kimenő frekvencia (Pr.08) és egyenlőnek vagy kevesebbnek, mint a MAximális feszültség frekvencia (Pr.04).
Ezzel a paraméterrel a középponti feszültség állítható be a V/F görbén belül. Így meghatározható a V/F aránya a Min. és a Középponti frekvencia között.
Ennek a paraméternek egyenlőnek vagy nagyobbnak kell lennie a Minimális kimenő feszültség (Pr.09) értékével és egyenlőnek vagy kevesebbnek kell lennie a Max. kimenő feszültség (Pr.05) értékével.
Ezzel a praméterrel lehet beállítani a minimális kimenő frekvenciát. Ennek a praméternek egyenlőnek vagy kevesebbnek kell lennie, mint a középponti frekvencia (Pr.06).
Ezzel a paraméterrel a minimális kimenő feszültséget állíthatod be. Ennek az értéknek kevesebbnek vagy egyenlőnek kell lennie a középponti feszültséggel (Pr.07).
Set valueNo.Pr.03 50.0Pr.04 50.0Pr.05 220.0Pr.06 2.2Pr.07 23.0Pr.08 1.3Pr.09 14.0
2.2
23
5-5
VFD-M Sorozat
Pr.10 Gyorsítási idő 1 Alaphelyzet: 10.0Pr.11 Lassítási idő 1 Alaphelyzet: 10.0Pr.12 Gyorsítási idő 2 Alaphelyzet: 10.0Pr.13 Lassítási idő 2 Alaphelyzet: 10.0
Beállítás 0.1 - 600.0 sec vagy 0.01 - 600.0 sec Egység: 0.1 v. 0.01 sec
Pr.10. Ezzel a paraméterrel azt az időt határozhatod meg, hogy mennyi idő alatt gyorsítson fel 0 Hz –ről a maximális kimenő frekvenciára (Pr.03). Az értéke mindig lineáris, kivéve ha az S –görbe funkció aktiválva van.
Pr.11. Ezzel a parméterrel azt az időt határozhatod meg, hogy mennyi idő alatt lassítson le a maximális kimenő frekvenciáról (Pr. 03) 0 Hz –re. Az értéke mindig lineáris, kivéve ha az S –görbe funkció aktiválva van.
A másodlagos Gyorsítás / Lassítás funkció a fent említett leírással megegyezően működik. Ekkor a multi funkciós bemeneti terminálnál ki kell választani ezt a funkciót és terminált le kell zárni 2. Gyorsítsá / Lassítás –ra. Lásd : Pr.38 – Pr.42.
Az alábbi ábra mutatja a 0 Hz –től a Maximális kimenő frekvenciáig a Gyorsítási / Lassítási időt. Feltételezve, hogy a maximális frekvencia (Pr.03) 60 Hz, és a indítási frekvencia (Pr.08) 1.0 Hz és a felfutási / lefutási idő 10 másodperc. Ebben az esetben az aktuális felfutási ideje az inverternek 9.83 másodperc és alefutási ideje szintén 9.83 másodperc.
Ezt a paramétert akkor érdemes használni, ha a Gyorsításnál / Lassításnál egy finomabb motor felpörgést akarunk elérni. Ha az alap értéke a Pr.11 –nek 0 vagyis alaphelyzetben van, akkor a Pr.14 mind a Gyorsításra és Lassításra eggyaránt vonatkozik. Ha a Pr.111 –et bármilyen más értékre állítjuk át mint “0” akkor a Pr.14 a gyorsításra és a Pr.111 a lassításra fog csak vonatkozni.
Freq.
Acceleration/Deceleration characteristics(1), (2) Disabling S curve(3), (4) Enabling S curve
Pr.15 Léptetési Gyorsítás / Lassítás idő Alaphelyzet: 1.0 sec Beállítás 0.1 - 600.0 sec v. 0.01 - 600.0 sec Egység: 0.1 v. 0.01 sec
Ez a parameter a léptetési módnál a gyorsítási / lassítási idő állítására szolgál.
A léptetési funkciót a Multi-funkciós bemeti terminálnál (M1-M5) lehet kiválasztani, ha az a Léptetési funkcióra van felprogramozzva. Ha a Léptetési funkció “zárva” van, akkor az inverter gyorsítani fog a minimális kimenő frekvenciáról (Pr.08) a léptető frekvenciára (Pr.16). Ha a léptető terminál “nyitva” van, akkor az inverter Lassítani fog a Léptető frekvenciáról egészen 0 –ig. A felfutási / lefutási idő így a léptetési felfutási / lefutási idő által van meghatározva (Pr.15). Működés alatt, az inverter nem hajt végre léptető parancsot és más parancs végrehajtása is tíltva van, kivéve az ELŐRE, HÁTRA és STOP gombok használata a digitális vezérlőn.
Ez a parameter a motor hátraforgathatósági funkciójának beállítására szolgál.
5-9
VFD-M Sorozat
Pr.25 Túlfeszültség elleni védelemBeállítás 230V sorozat 330-450Vdc Alaphelyzet: 390
460V sorozat 660-900Vdc Alaphelyzet: 780 00 funkció tiltva
A lassításnál felléphet egy olyan jelenség, hogy a DC BUSZ túllépi a maximálisan megengedett feszültséget a motor áramvisszatermelése miatt. Ha ez a funkció engedélyezve van, akkor az inverter leállítja a lassítást és egy állandó kimenő frekvenciát fog adni a motor felé. Ha viszont a feszültség eközben lecsökken a már megengedhető értékre, akkor a frekvenciaváltó tovább fojtatja a lassítás a már elért frekvenciáról a beállított értékre a már előre megadott paraméterek alpján.
Megjegyzés: Közepesen nagy terheléseknél ilyen fajta jelenség nem észlelhető, ami túlfeszültséget okozhatna. Csak olyan helyzetben állhat fenn, ha a nagyon nagy forgó tömegeket kell gyorsan fékezni. Ilyenkor az inverter automatikusan megnyújtja a fékezési időt. Ha ez a megoldás nem lehetséges, ebben az esetben fék ellenállást kell beszerelni a dinamikus fékezés megvalósítsához.
A 100% -os állás a frekvenciaváltó névleges kimenő áramerősségével egyenlő érték.
Bizonyos esetekben, az inverter áramfelvétele hirtelen megnőhet és elérheti a max. megengedett értéket, amit a Pr.26. –ban be lett állítva. Ezt általában hirtelen gyorsítás vagy túl nagy pillanatnyi terhelés okozhatja. Ha eza funkció engedélyezve van, akkor az inverter, megállítja a gyorsítást, és egy frekvenciaszinten beáll, addíg amíg az áramfelvétel értéke újból vissza nem esik a megengedett érték alá. Ha ez megtörtént, akkor az inverter tovább folytatja a gyorsítást a már előre beállított értékek szerint.
Pr.27 Over-Current Stall Prevention during Operation Alaphelyzet: 150%Settings 20 to 200% Egység: 1%
00: disable
During the steady-state operation with motor load rapidly increasing, the AC drive output current may exceed the limit specified in Pr.27. When this occurs, the output frequency will decrease to maintain a constant motor speed. The drive will accelerate to the steady-state output frequency only when the output current drops below the level specified by Pr.27.
Ezzel a paraméterrel meghatározhatja a fékezési áramfelvételt a motoron az indítás és megállítás ideje alatt. Amikor a DC fékezési áramot állítja be, kérem vegye figyelembe, hogy a 100% érték = a motor névleges áramfelvételével. Javasolt, hogy alacsony értékkel kezdje a DC fék beállítását, és majd növelje a megfelelő nyomaték szintjének eléréséig.
Pr.29 DC Fékezési idő az indításnál Alaphelyzet: 0.0 Beállítás 0.0 to 5.0 sec Egység: 0.1sec
5-11
VFD-M Sorozat
Ez a paraméter a DC fék This parameter determines the duration of time that the DC Braking Current will be applied to the motor during the AC drive start-up. DC Braking will be applied for the time set in this parameter until the Minimum Frequency is reached during acceleration.
Pr.30 DC Braking Time during Stopping Alaphelyzet: 0.0 Beállítás 0.0 to 25.0 sec Egység: 0.1sec
This parameter determines the duration of time that the DC braking voltage will be applied to the motor during stopping. If stopping with DC Braking is desired, then Pr.02 must be set to RAMP to stop (0.0).
Pr.31 Start-Point for DC Braking Alaphelyzet: 0.00 Beállítás 0.00 to 60.00Hz Egység: 0.1sec
This parameter determines the frequency when DC Braking will begin during deceleration.
MasterFrequency
Min. outputFreq.
Pr.29
Pr.31
Pr.30
DC Braking Current %
ON OFF
Pr.28
Start-pointfor DCbraking
Operationcommand
time(s)
Note:
1. DC Braking during Start-up is used for loads that may move before AC drive starts, such as fans and pumps. These loads may also be moving in the wrong direction. Under such circumstances, DC Braking can be executed to hold the load in position before applying a forward motion.
2. DC Braking during stopping is used to decrease stopping time and also to hold a stopped load in position. For high inertial loads, a dynamic braking resistor may be needed for quick decelerations.
Pr.32 Momentary Power Loss Operation Selection Alaphelyzet: 00Beállítás 00 Operation stops after momentary power loss
01 Operation continues after momentary power loss speed search starts with the Master Frequency reference value
02 Operation continues after momentary power loss Speed search starts with the min frequency
Pr.33 Maximum Allowable Power Loss Time Alaphelyzet: 2.0 sec Beállítás 0.3 to 5.0 sec Egység: 0.1sec
During a power loss, if the power loss time is less than the time defined by this parameter, the AC drive will resume operation. If the Maximum Allowable Power Loss Time is exceeded, the AC drive output is then turned off.
Pr.34 Base-Block Time for Speed Search Alaphelyzet: 0.5 sec Beállítás 0.3 to 5.0 sec Egység: 0.1sec
When a momentary power loss is detected, the AC drive turns off for a specified time interval determined by Pr.34 before resuming operation. This time interval is called Base-Block. This parameter should be set to a value where the residual output voltage due to regeneration is nearly zero, before the drive resumes operation.
This parameter also determines the searching time when performing external Base-Block and Fault Reset (Pr.72).
Pr.35 Maximum Speed Search Current Level Alaphelyzet: 150 Beállítás 30 to 200% Egység: 1%
5-13
VFD-M Sorozat
Following a power failure, the AC drive will start its speed search operation, only if the output current is greater than the value determined by Pr.35. When the output current is less than that of Pr.35, the AC drive output frequency is at a “speed synchronization point”. The drive will start to accelerate or decelerate back to the operating frequency at which it was running prior to the power failure.
InputPower
Allowable Max. Power Loss Time
OutputPower
OutputVoltage
Pr.33
Speed search starts withthe Master Frequency
Pr.32=1
BaseblockTimePr.34
speed synchronizationdetection
speed search
Allowable Max. power loss time
Pr.33
Speed search starts withminimum output frequency
Pr.32=2
BaseblockTimePr.34
Pr.36 Upper Bound of Output Frequency Alaphelyzet: 400 Beállítás 0.10 Hz to 400.0 Hz Egység: 0.1Hz
This parameter must be equal to or greater than the Lower Bound of Output Frequency (Pr.37).
Pr.37 Lower Bound of Output Frequency Alaphelyzet: 0 Hz Beállítás 0.00 Hz to 400.0 Hz Egység: 0.1Hz
The Upper/Lower Bound is to prevent operation error and machine damage.
If the Upper Bound of Output Frequency is 50Hz and the Maximum Output Frequency is 60Hz, the Maximum Output Frequency will be limited to 50Hz.
If the Lower Bound of Output Frequency is 10Hz, and the Minimum Output Frequency (Pr.08) is set at 1.0Hz, then any Command Frequency between 1-10Hz will generate a 10Hz output from the drive.
This parameter must be equal to or less than the Upper Bound of Output Frequency.
00: Két vezetékes működtetés: Csak a Pr.38 –t kell 0 –ra állítani.
FWD/STOP
REV/STOP
M0 "Open": Stop, "Close": FWD Run
M1 "Open": Stop, "Close":REV Run
GND
01: Két vezetékes működtetés: Csak a Pr.38 –t kell állítani 1 -re
RUN/STOP
REV/FWD
M0 "Open": Stop, "Close": Run
M1 "Open": FWD, "Close":REV
GND
Note: Multi-function Input Terminal M0 does not have its own parameter designation. M0 must be used in conjunction with M1 to operate two and three wire control.
5-15
VFD-M Sorozat
02 Három vezetékes vezérlés: Csak a Pr.38 –t kell 2 –re állítani.
STOP RUN
RUN/FWD
M0 Run command, Runs when "close" M2 Stop command, stops when "Open"
M1 REV/FWD Run selection"Open": FWD Run"Close": REV RunGND
Note: When 2 is selected for Pr.38, the value in Pr.39 will be ignored.
Érték Funkció Érték Funkció00 No Function 01 WG OFF (N.O.) (it is enable during
running)02 WG OFF (N.C.) (it is enable during
running)03 External Fault (N.O.)
04 External Fault (N.C.) 05 External Reset06 Multi-Step Speed Command 1 07 Multi-Step Speed Command 208 Multi-Step Speed Command 3 09 Jog Operation10 Accel/Decel Speed Inhibit 11 First or Second Accel/Decel Time
Selection12 External Base Block (N.O.)
(Normally Open Contact Input) 13 External Base Block (N.C.)
(Normally Close Contact Input)14 Increase Master Frequency 15 Decrease Master Frequency 16 Run PLC Program 17 Pause PLC Program18 Counter Trigger Signal 19 Counter Reset20 No Function 21 RESET Command (N.C)22 Control Place: External Terminal 23 Control Place: Keypad24 Control Place: Communication 25 Parameter Lock (Write disable, Read is
always 0)26 PID Disable (N.O.) 27 PID Disable (N.C.)28 The Second Source of Frequency
Command29 Forward (contact is open) / Reverse
(contact is close)30 One-Shot PLC Run 31 Index Input Signal32 Virtual Timer Input
5-17
VFD-M Sorozat
Magyarázat:
00: nincs funkció társítva01, 02: when it is set to 01 or 02, AC drive will stop outputting immediately. If there is start
signal after disabling, the output will start from the minimum frequency.03, 04 Külső hiba: Parameter values 3, 4 program Multi-Function Input Terminals: M1
(Pr.38), M2 (Pr.39), M3 (Pr.40), M4 (Pr.41) or M5 (Pr.42) to be External Fault (E.F.) inputs.
GND
E.F.(N.O.)
setting by 3
E.F(N.C.)
setting by 4
Mx "Close": Operation available.
Mx "Open":Operation available.
Note: When an External Fault input signal is received, the AC drive output will turn off, the drive will display “ E.F.” on Digital Keypad, and the motor will free run. Normal operation can resume after the External Fault is cleared and the AC drive is reset.
05 Külső Reset:Parameter value 5 programs a Multi-Function Input Terminal: M1 (Pr.38), M2 (Pr.39), M3 (Pr.40), M4 (Pr.41) or M5 (Pr.42) to be an External Reset.
GND
RESET
setting by 5Mx "Close": Operation avalilable
Note: the External Reset has the same function as the Reset key on the Digital keypad. It is to reset the drive after a fault.
06, 07, 08 Multi-Step Speed Command:Parameter values 06, 07, 08 programs any three of the following Multi-Function Input Terminals: M1 (Pr.38), M2 (Pr.39), M3 (Pr.40), M4 (Pr.41) or M5 (Pr.42) for Multi-step Speed Command function.
Note: These three inputs select the multi-step speeds defined by Pr.17 to Pr.23 as shown in the following diagram. Pr.78 to Pr.87 can also control output speed by programming the AC drive’s internal PLC function.
Freq.Step 1
Step 2
Step 3Step 4
Step 5Step 6
Step 7
Time
OFF
ON ON
ON ON
ON ON
ON ON
ON ON ON ON
ONOperationCommand
Mx3-GND
Mx2-GND
Mx1-GND
Pr.17
Pr.18
Pr.19Pr.20
Pr.21Pr.22
Pr.23
Master Freq.
09 Léptetési működés vezérlése:Parameter value 09 programs Multi-Function Input Terminal: M1 (Pr.38), M2 (Pr.39), M3 (Pr.40), M4 (Pr.41) or M5 (Pr.42) for Jog control.
GND
Mx "Close": Operation available9 jog operationcommand
Note: Jog operation programmed by 9 can only be initiated while the motor is stopped. (Refer to Pr.15, Pr.16.)
10 Accel/Decel Speed Inhibit:
5-19
VFD-M Sorozat
Parameter value 10 programs Multi-Function Input Terminal: M1 (Pr.38), M2 (Pr.39), M3 (Pr.40), M4 (Pr.41) or M5 (Pr.42) for Accel/Decel Inhibit. When the command is received, acceleration and deceleration is stopped and the AC drive maintains a constant speed.
Frequency Master Frequency
Accel inhibit
Accel inhibit
Actual operation frequency
Decelinhibit
Decelinhibit
Time
Mx-GNDOperationcommand
ON ON ON ON
ON OFF
11 First or Second Accel/Decel Time Selection:Parameter value 11 programs a Multi-Function Input Terminal: M1 (Pr.38), M2 (Pr.39), M3 (Pr.40), M4 (Pr.41) or M5 (Pr.42) to control selection of First or Second Accel/Decel time. (Refer to Pr.10 to Pr.13.)
GND
Mx "Close": 2nd Accel/DecelMx set 11 "Open": 1st Accel/Decel
12, 13 External Base Block:Parameter values 12, 13 program Multi-Function Input Terminals: M1 (Pr.38), M2 (Pr.39), M3 (Pr.40), M4 (Pr.41) or M5 (Pr.42) for external Base Block control. Value 12 is for normally open (N.O.) input, and value 13 is for a N.C. input.
GND
B.B.(N.O.)
setting by 12
B.B.(N.C.)
setting by 4
Mx "Close": Operation available.
Mx "Open":Operation available.
Note: When a Base-Block signal is received, the AC drive will stop all output and the motor will free run. When base block control is deactivated, the AC drive will start its speed search function and synchronize with the motor speed, and then accelerate to Master Frequency.
Externalbase-blocksignal
Outputfrequency
OutputvoltageCapacitordischarge
Allowable max. power loss time
Pr.33
Speed search starts with thereference value
Low voltage Pr.34
Min. base-block time
Low voltage Speed search operation
Pr.32=1 Speed synchronizationdetection
14, 15 Frekvencia Nöselés / Csökkentés:A 14, 15 paraméter értékek beállítják a Multi-Funkciós bemeneti terminált: M1 (Pr. 38), M2 (Pr. 39), M3 (Pr. 40), M4 (Pr. 41) vagy M5 (Pr. 42) –t, hogy növeljék / csökkentsék a frekvenciát minden egyes alakalommal, mikor bemeneti jel érkeik a terminálon keresztül.
16, 17 PLC vezérlési funkciók:Parameter value 16 programs Multi-Function Input Terminal: M1 (Pr.38), M2 (Pr.39), M3 (Pr.40), M4 (Pr.41) or M5 (Pr.42) to enable the AC drive internal PLC program. Parameter value 17 programs an input terminal to pause the PLC program.
GND
setting by 16
setting by 17
Mx "Close": Run PLC.
Mx "Open":Pause PLC.
PLC operation
Note: Pr.17 to Pr.23, Pr.78, Pr. 79, Pr.81 to Pr.87 define the PLC program. Another related function is “30 One-Shot PLC Run”, it can be set to use not-latched contact to be run signal.
18 Counter Trigger:Parameter value 18 programs Multi-Function Input Terminal: M1 (Pr.38), M2 (Pr.39), M3 (Pr.40), M4 (Pr.41) or M5 (Pr.42) to increase the AC drive’s internal counter. When an input is received, the counter is increased by 1.
GND
18 countertrigger signalinput.
Mx counter value increase by1 when closed.
Trigger
Note: The Counter Trigger input can be connected to an external Pulse Signal Generator to count a processing step or unit of material. See the diagram below.
Signal output with Pr.96counter value is attained.
(Pr.96=5)(Pr.45/46)
The trigger timingcan't be less than2ms.(<250Hz)
5-23
VFD-M Sorozat
19 Számláló Reset:Parameter value 19 programs Multi-Function Input Terminal: M1 (Pr.38), M2 (Pr.39), M3 (Pr.40), M4 (Pr.41) or M5 (Pr.42) to reset the counter.
GND
19 reset the counter value.
Mx "close": reset counter.Reset counter
20 Parameter Disable:Enter value (20) to disable any Multi-Function Input Terminal: M1 (Pr.38), M2 (Pr.39), M3 (Pr.40), M4 (Pr.41) or M5 (Pr.42)
Note: The purpose of this function is to provide isolation for unused Multi-Function Input Terminals. Any unused terminals should be programmed to 20 to insure they have no effect on drive operation.
Enter value (22, 23, 24) to force control command to external terminal, keypad or communication. This function can be used to divide the function of manual/auto operation, remote/near-end control. When these three functions are used at the same time, the priority is 22 Control Place: I/O > 23 Control Place: Keypad > 24 Control Place: Communication.
25 Parameter Lock (Write disable, Read is always 0)This function will disable write function and all the content of read are 0. The application is
for customer having a key to control the operator to modify parameters or modify the parameter by improper use.
26 PID Funkció letiltása (N.O.) / 27 PID Funkció letiltása (N.C.)These functions can make the PID control pause. It is usually used on the manual
operation or function test of water pump or wind power generator and recover the PID function when the system is normal.
This function is used with Pr. 142. The application is for customers select the different frequency source in different mode.
29 Előre forgás (Nyitott kapcsolat) / Hátra forgás (Zárt kapcsolat)
This function has high priority to set the direction of run (If “Pr. 24 inhibit REV function” is not set). No mater what the present direction of run is, the contact N.O. is forward and the contact N.C. is reverse after setting this function.
The priority of setting the direction is Pr. 24 > setting 29 of Pr. 39-Pr42 > Pr. 38.
31 Index Input Signal
This function is used with Pr. 149-Pr. 151. The position where AC drive stops will be regarded as the zero position and it will move to the angle that Pr. 150 sets.
32 Counter Incremented by Drive Output Frequency
This counter will count according to the speed of output frequency.
Note: You can select settings 00~02 of Pr.38 to set multi-function terminals (M0, M1). The settings 00~32 of Pr. 39-Pr.42 can be used to set multi-function terminals (M2-M5) but the settings can’t be used repeatedly at one time (besides settings 20). There is no order to set the multi-function terminal, you can set these five terminals by yourself.
The parameter sets the voltage range of analog output signal, on output terminal AFM.
+ -
AFM GND
Analog Frequency Meter
+ -
AFM GND
Analog Current Meter
The analog output voltage is directly proportional to the output frequency of the AC drive. With the factory setting of 100%, the Maximum Output Frequency (Pr.03) of the AC drive corresponds to +10VDC analog voltage output. (The actual voltage is about +10VDC, and can be adjusted by Pr.44)
The analog output voltage is directly proportional to the output current of the AC drive. With the factory setting of 100%, the 2.5 times rated current of the AC drive corresponds to +10 VDC analog voltage output. (The actual voltage is about +10 VDC, and can be adjusted by Pr.44)
Note: Any type of voltmeter can be used. If the meter reads full scale at a voltage less than 10 volts, then Pr.44 should be set by the following formula:
Pr.44 = ((meter full scale voltage)/10)×100%
For Example: When using the meter with full scale of 5 volts, adjust Pr.44 to 50%
06 AC Drive Operation Mode 19 Over Heat supervision07 Fault Indication 20 Over Current stall supervision08 Desired Frequency Attained 21 Over voltage stall supervision09 PLC Program Running 22 Forward command10 PLC Program Step Completed 23 Reverse command11 PLC Program Completed 24 Zero Speed (Include Drive Stop)12 PLC Operation Paused
Function Explanations:
00 AC drive operational: the terminal will be activated when there is an output from the
drive.
01 Maximum Output Frequency Attained: the terminal will be activated when the AC
drive attains Maximum Output Frequency.
02 Nulla sebesség: the output will be activated when Command Frequency is lower than
the Minimum Output Frequency.
03 Túl – nyomaték felismerés: the output will be activated as long as the over-torque is
detected. Pr.61 determines the Over-Torque detection level.
04 Base-Block (B.B.) Indication: the output will be activated when the output of the AC
drive is shut off by external Baseblock.
05 Alacsony feszültség figyelés: the output will be activated when low voltage is detected.
06 AC Drive Operation Mode: the output will be activated when the operation of the AC
drive is controlled by External Control Terminals.
07 Hiba figyelés: the output will be activated when faults occur (oc, ov, oH, oL, oL1, EF,
cF3, HPF, ocA, ocd, ocn, GF).
08 Desired Frequency Attained: the output will be activated when the desired frequency
(Pr.47) is attained.
09 PLC Program futás: the output will be activated when the PLC program is running.
10 PLC Program lépés végrehajtva: the output will be activated for 0.5 sec. when each
multi-step speed is attained.
5-27
VFD-M Sorozat
11 PLC Program lefutott: the output will be activated for 0.5 sec. when the PLC
program cycle has completed.
12 PLC Program futása megállítva: the output will be activated when PLC operation is paused.
13 Terminal Count Value Attained: counter reaches Terminal Count Value.14 Preliminary Count Value Attained: counter reaches Preliminary Count Value. 15 Figyelmeztetés (PID feedback loss, communication error): The contact will be
“close” when PID feedback loss or communication is error.16 Below the Desired Frequency: the contact will be “close” when output frequency is
less than desired frequency.17 PID supervision: the contact will be “close” when PID offset exceeds the setting of
P126 and P127.18 Over voltage supervision: the contact will be “close” before over voltage. It will be
activated at 370Vdc in 230V series and at 740Vdc in 460 series.19 Over Heat supervision: the contact will be “close” before 90°C.20 Over Current stall supervision: the contact will be “close” before exceeding the
setting of P26/P27.21 Over voltage stall supervision: the contact will be “close” before exceeding the
setting of P25.22 Előreforgás parancs: the contact will be “close” with forward command.23 Hátraforgás parancs: the contact will be “close” with reverse command.24 Nulla sebesség (Include Drive Stop): the contact will be “close” when the setting
frequency is less than min. frequency or drive stop.
Pr.47 Desired Frequency Attained Factory Setting: 0.00 Settings 0.00 to 400.0 Hz Egység: 0.1Hz
If a Multi-function output terminal is set to function as Desired Frequency Attained (Pr.45 or 46=09), then the output will be activated when the programmed frequency is attained.
Desired Freq. Detection range-2Hz
Detectionrange+-4Hz
Detection range
+-2Hz
Time
Freq.
Max. OutputFreq.
ON
ON
OFF OFF
OFF OFF
Preset Freq.Attained IndicationPr.45 to Pr.46
Desired Freq.Attained IndicationPr.45 & Pr.46
Desired Freq. Attained & Preset Freq. Attained
Pr.47
Pr.48 Adjust Bias of External Input Frequency Factory Setting: 0.00 Hz Settings 0.00 to 100.0% Unit: 0.1Hz
This parameter provides a frequency offset for analog input.
Példa 1:The following is the most common method. Setting Pr.00 to 1 (0 to +10V signal) or 2 (4 to 20mA current signal) to use potentiometer on keypad or potentiometer/current signal of external terminal to set frequency.
Példa 2:In this example with the potentiometer set to 0V the Output Frequency is 10 Hz. The mid-point of the potentiometer becomes 40 Hz. Once the Maximum Output Frequency is reached any further increase of the potentiometer will not increase output frequency. (If you want to use the range of 60Hz, please refer to the example 3.) The value of external input voltage/current 0-8.33V (4-13.33mA) corresponds to the setting frequency 0-60Hz.
Példa 3:The example also shows the popular method. The whole scale of the potentiometer can be used as desired. In addition to signals of 0 to 10V and 4 to 20mA, the popular voltage signals also include signals of 0 to 5V, 20 to 4mA or that under 10V. Regarding the setting, please refer to the following examples.
5-31
VFD-M Sorozat
Max.OutputFreq.
Pr.03
BiasAdjustment
0V 10V4mA
0Hz
10Hz
60Hz
20mA-2VXV
Pr. 50 = X 100% 83.3% = 10V12V
Negative bias:60-10Hz
10V10-0Hz
XV =
XV = 10050 = 2V
Pr.48 = X 100%210
Potentiometer Scale
Hz0V 10V
35
0 60
Példa 4:This example shows a potentiometer range of 0 to 5 Volts. In addition to adjust gain, you also can set Pr. 03 to 120Hz.
Példa 5:In this example a 1-volt negative bias is used. In a noisy environment, it is advantageous to use negative bias to provide a noise margin (1V in this example).
Példa 6:In this example, a negative bias is used to provide a noise margin. Also a potentiometer frequency gain is used to allow the Maximum Output Frequency to be reached.
Példa 7:Ennél a példánál a potencióméter úgyvan beállítva, hogy a motort egyszerre mindkét irányba lehessen forgatni. A motor áll, ha a pot.méter pont középen áll és jobbra vagy balra forgatással előre/hátra fog forogni. Ez a beállítás használva a külsö Előr/Hátra parancs nem működik.
Példa 8:In this example, the option of anti-slope is shown. Anti-slope is used in an application where control of pressure, temperature, or flow is needed. Under a high pressure or flow situation, a sensor will generate a large signal such as 20 mA or 10V. With anti-slope enable, the large signal will slow or stop the AC drive. The limit in this application is can’t change the direction of run. For AC drive, it just can run in reverse direction.
Pr.52 Motor névleges áramfelvétele Factory Setting: FLA Settings 30.0% FLA to 120.0% FLA Unit: 0.1A
This parameter must be set according to the nameplate of AC drive. The factory setting will be set by the rated power of AC drive. You can use this parameter to limit the output current of motor to prevent overheat. Using the following method to calculate the percentage entered in this parameter. (no-load current < rated current of motor <rate current of AC drive)
The factory setting is the full-load rated current (FLA) of AC drive. The value that this parameter displays is the actual current and you just need to input the current on the nameplate without calculating.
Pr.53 Motor terhelés nélküli áramfelvétele Factory Setting: 0.4*FLA Settings 00%FLA to 99%FLA Unit: 0.1A
The rated current of the AC drive equals 100%. Setting of motor No-Load Current will affect the slip compensation function. The setting value must be less than motor rated current setting Pr.52. (this parameter displays the value of actual current.)
When providing an asynchronous induction motor, load on the AC drive will increase causing an increase in slip. This parameter may be used to compensate the nominal slip within a range of 0 to 10. When the output current of the AC drive is greater than the motor no-load current (Pr.53), the AC drive will adjust its output frequency according to this parameter.
Pr.56 Lefoglalva
Pr.57 Inverter névleges áramfelvétalének kijelzése Alaphelyzet: ##.# Beállítás Nincs
Ez a paraméter az inverter névleges áramfelvétalét írja ki a kijelzőre. Pr. 80 ugyanezt kiírja a modelszámmal együtt. Nézd meg a Pr. 80 –as funkciót a további információért.
Pr.58 Elektronikus túlterhelés elleni védelem Alaphelyzet: 02 Beállítás 00 Standard Motor (Saját hűtésű motor)
01 Inverter Motor (Kényszerhűtéses motor)02 Kikapcsolva
This function is used to limit the output power of the AC drive when powering a “self-cooled motor” at low speed.
Pr.59 Electronikus Motor túlterhelés elleni védelem Factory Setting: 60 Beállítás 30 to 300sec Unit: 1 second
The parameter determines the time required activating the I2t electronic thermal motor overload function. The graph below shows I2t curves for 150% output power for 1 minute.
This parameter is used to define the run mode of AC drive after over-torque detection. When output current is large than over-torque detection level (Pr.61), over-torque detection time (Pr.62) is time out and the multi-function terminals is set to over-torque detection indication, this contact will be “close”. (Please refer to Pr. 45 and Pr.46)
Settings 00 Decelerate to 0 Hz01 Stop immediately and display "EF"02 Continue operation by last freq. Command
Pr.64 User Defined Function for Display Factory Setting: 06 Settings 00 Displays AC drive output frequency (Hz)
01 Display User-defined output Frequency H*Pr.6502 Kimenő feszültség (E)
03 DC Bus Voltage (u)04 PV (i)05 Displays the value of the internal counter (c)
06 Displays the setting Frequency (F)07 Displays the parameter setting (P)08 Reserved09 Output Current (A)10 Display program operation (0. xxx), Fwd, or Rev
The parameter can be set to display the user-defined value. (where v = H x Pr.65 )
Ez a K állandó egy szorzó tényező az ügyfél által kijelezendő értékhez.
A kijelzendő érték a következő képpen számítható:
Kijelzett érték = Kimenő frekvencia x K
A kijelző csak négyjegű szám kimutatására képes. Nagyobb szám kijelzéséhez használd a Pr. 65 –ös funkciót. The display windows uses decimal points to signify numbers up to three digits as illustrated next page:
Kijelző Number Represented
9999 The absence of a decimal point indicates a four-digit integer.
999.9 A signal decimal point between the middle and the right-most numbers is a true decimal point. For example, the number 123.4 would be displayed as “123.4”.
9999. A single decimal point after the right-most number is not a true decimal point;
5-37
VFD-M Sorozat
instead it indicates that a zero follows the right-most number. For example, the number 12340 would be displayed as “1234.”
999.9. Two decimal points (one between the middle and the right-most numbers, and one after the right-most number) are not true decimal points; instead they indicate that two zeros follow the right-most number. For example, the number 345600 would be displayed as “345.6.”.
Ezzel a három paraméterrel meghatározhatod azokat a frekvenciákat, amit működés közben el szeretnél kerülni. These three parameters determine the three Skip Frequencies that in conjunction with Pr.70, Skip Frequency Band, will cause the AC motor drives to skip operation at each frequency band. Note: Pr.67 > Pr.68 > Pr.69.
Pr.70 Skip Frequency Band Factory Setting: 0.00 Settings 0.00 to 20.00 Hz Unit: 0.1 Hz
This parameter determines the frequency band for a given Skip Frequency. Half of the Skip Frequency Band is above the Skip Frequency and the other half is below. Programming this parameter to 0.1 disables all skip frequencies.
From the above table, we see that the carrier frequency of PWM output has a significant influence on the electromagnetic noise, heat dissipation of the AC drive, and the acoustic noise to the motor.
After fault occurs (allowable faults: over-current OC, over-voltage OV), the AC drive can be reset/restarted automatically up to 10 times. Setting this parameter to 0 will disable the reset/restart operation after any fault has occurred. When enabled, the AC drive will restart with speed search, which starts at the Master Frequency. To set the fault recovery time after a fault, please see (Pr.34) base-block time for speed search.
5-39
VFD-M Sorozat
Pr.73 Jelenlegi hiba naplózása Factory Setting: 00Pr.74 A 2. legtöbbet előforduló hiba naplózása Factory Setting: 00Pr.75 A 3. legtöbbet előforduló hiba naplózása Factory Setting: 00
Beállítás 00 (no fault occurred )01 Túláram (oc)02 Túlfeszültség (ov)
03 Túlmelegedés (oH)04 Túlterhelés (oL)05 Túlterhelsé 1 (oL1)06 Külső hiba (EF)07 CPU hiba 1 (CF1)08 CPU hiba 3 (CF3)09 Hardware védelmi hiba (HPF)10 Túláram gyorsítás alatt (OCA)11 Túláram lassítás alatt (OCd)12 Over-current during steady state operation (OCn)13 Földelési vagy biztosíték hiba (GFF)14 Alacsony feszültség (not record)15 3 Phase Input Power Loss16 CPU hiba (CF2)17 External Base-Block (bb)18 Túlterhelés 2 (oL2)19 Auto Adjustable accel/decel failure (cFA)20 Software védelmi code hiba (codE)
Pr.76 Paraméterzárolás és konfigurálás Alaphelyzet: 00 Beállítás 00 Minden paraméter változtatható és olvasható
01 Minden paraméter csak olvasható02-08 Foglalt
10 Minden parmétert az alaphelyzetre állít vissza. RESET
Ezzel a funkcióval lehet RESET –elni a frekvenciaváltót. Így minden parameter az eredeti gyári állapotba kerül beállításra.
Pr.77 Time for Auto Reset the Restart Times after Fault Factory Setting: 60.0 Settings 0.1 to 600.0 sec Unit: 0.1 second
01 Egy programm ciklust hajt végre02 Folyamatos programm ciklus végrhajtás03 Lépésről lépésre hajtja végre a programmot (“STOP” –al minden
lépésnél)04 Continuously execute program cycles step by step (separated by
“STOP”)
This parameter selects the mode of PLC operation for the AC drive. The PLC program can be used in lieu of any External Controls, Relays or Switches. The AC drive will change speeds and directions according to the user’s desired programming.
Example 1 (Pr.78 =01): Execute one cycle of the PLC program. Its relative parameter settings are:
1 Pr.17 to Pr.23: 1st to 7th step speed (sets the frequency of each step speed)
2 Pr.38 to Pr.42: Multi-Function Input Terminals (set one multi-function terminal as 16- PLC
auto-operation).
3 Pr.45 to Pr.46: Multi-Function Output Terminals (set a Multi-Function Terminal as 09-PLC
operation indication, 10-one cycle in PLC auto mode or 11-PLC operation fulfillment
attainment).
4 Pr.78: PLC mode.
5 Pr.79: Direction of operation for Master Frequency and 1st to 7th step speed.
6 Pr.81 to Pr.87: operation time setting of Master Frequency and 1st to 7th step speeds.
Example 1 (Pr.78 = 01) Execute one cycle through the PLC program:
Note: The above diagram shows one complete PLC cycle. To restart the cycle, turn the PLC Program input off and then back on.
Example 2 (Pr.78 = 02) Continuously executes program cycles:The diagram below shows the PLC program stepping through each speed and then automatically starting again. To stop the PLC program, either pause or stop the program. (Refer to Pr.38 to Pr.42 value 17 and 18)
Example 3 (Pr.78 = 03) Execute one cycle step by step:This example shows how the PLC function can perform one cycle at a time, within a complete cycle. Each step will use the accel/decel times in Pr.10 to Pr.13. It should be noted that the time interval for each step is reduced due to the time for acceleration and deceleration.
Note: operating time for each step is 10 times the settings of Pr.81 to Pr.87.
t t t t t t t
Example 4 (Pr.78 = 04) Continuously executes program cycles step by step:In this explanation, the PLC program runs continuously step by step. Also shown are examples of steps in the reserve direction.
Note: operating time for each step is 10 times the settings of Pr.81 to Pr.87.
t
Pr.82 t
t t t
Pr.86 t
t
*
Pr.17
Time
Pr.81
FWD
REV
5-43
VFD-M Sorozat
Example 5 (Pr.78 = 01) Execute one cycle through the PLC program: In this example, the PLC program runs continuously. It should be noted that the times of reserve motion may be shorter than expected, due to the accel/decel time.
Application Note:Changing the value of Jog parameters 15 and 16 will interrupt PLC program execution. PLC program execution will not be interrupted when and other parameter values are changed.
This parameter controls the direction of motion for the multi-speed Pr.17 to Pr.23 and the Master Frequency. The original direction of Master Frequency will become invalid.
Note: The equivalent 7-bit number is used to program the forward/reverse motion for each of the 8 speed steps (including Master Frequency). The binary notation for the 7-bit number must be translated into decimal notation and then be entered.
1234567
WeightsBit
0=Forward1=Reverse
Direction of 1st Pr.17 speed for
Direction of 2nd Pr.18 speed for Direction of 3rd Pr.19 speed for Direction of 4th Pr.20 speed for Direction of 5 Pr.21th speed for Direction of 6 Pr.22th speed for Direction of 7 Pr.23th speed for
Setting example:
1234567
Weights
Bit
0=Forward1=Reverse
Forward motion of Pr.17 multi-speed1
Reverse motion of Pr.18 multi-speed2Forward motion of Pr.19 multi-speed3Forward motion of Pr.20 multi-speed4Forward motion of Pr.21 multi-speed5Reverse motion of Pr.22 multi-speed6Forward motion of Pr.23 multi-speed7
0100010Direction
The setting value=bit7 x 26+bit6 x 25+bit5 x 24+bit4 x 23+bit3 x 22+bit2 x 21+bit1 x 20
= 0 x 26+1 x 25+0 x 24+0 x 23+0 x 22+1 x 21+0 x 20
Pr.81 Time Duration of 1st Step Speed (correspond to Pr.17) Factory Setting: 00Pr.82 Time Duration of 2nd Step Speed (correspond to Pr.18) Factory Setting: 00Pr.83 Time Duration of 3rd Step Speed (correspond to Pr.19) Factory Setting: 00Pr.84 Time Duration of 4th Step Speed (correspond to Pr.20) Factory Setting: 00Pr.85 Time Duration of 5th Step Speed (correspond to Pr.21) Factory Setting: 00Pr.86 Time Duration of 6th Step Speed (correspond to Pr.22) Factory Setting: 00Pr.87 Time Duration of 7th Step Speed (correspond to Pr.23) Alaphelyzet: 00
Settings 00 to 9999 second Unit: 1 sec
Pr.81 to Pr.87 correspond to operation time of each Multi-step speed defined by Pr.17 to Pr.23.
Note: If a parameter is set to “0” (0 Sec), the corresponding step will be skipped. This is commonly used to reduce number of program steps.
Pr.88 Kommunikációs cím Alaphelyzet: 01 Beállítás 01 - 254
01 Baud rate 9600 (adatátviteli sebesség: bit / sec)02 Baud rate 19200 (adatátviteli sebesség: bit / sec)03 Baud rate 38400 (adatátviteli sebesség: bit / sec)
Users can set parameters and control the operation of the AC drive via the RS-485 serial interface of a personal computer. This parameter is used to set the transmission speed between the computer and AC drive.
Settings 00 Warn and Continue Operating01 Warn and RAMP to Stop02 Warn and COAST to Stop03 Keep Operation without Warning
Pr.91 Idő túllépés észlelés Factory Setting: 0.0
Beállítás 0.1 to 120.0 sec 0.0 disable
This parameter is used for ASCII mode. When this parameter is set to 01, indicates that the over-time detection is enable, the time slot between each character cannot exceed 500 ms.
1. Computer vezérlés There is a built-in RS-485 serial interface, marked (RJ-11 Jack) on the control terminal
block, for VFD Series. The pins are defined below:
5-47
VFD-M Sorozat
6 1
1: +15V2: GND3: SG-4: SG+5: NC6: for communication
Each VFD-M AC drive has a pre-assigned communication address specified by Pr.88. The computer then controls each AC drive according to its communication address.
VFD-M can be setup to communicate on Modbus networks using one of the following modes: ASCII (American Standard Code for Information Interchange). Users can select the desired mode along with the serial port communication protocol in Pr.92 and Pr.113.
Code Meaning:
ASCII mode:
Each 8-bit data is the combination of two ASCII characters. For example, a 1-byte data: 64 Hex, shown as ‘64’ in ASCII, consists of ‘6’ (36Hex) and ‘4’ (34Hex).
Kommunikációs cím:8-bit cím address consists of 2 ASCII codes
5-49
VFD-M Sorozat
STX Start karakter: (3AH) DATA (n-1)
……DATA 0
Adat tartalom:n x 8-bit data consist of 2n ASCII codes.n≦25 maximum of 50 ASCII codes
LRC CHK 1LRC CHK 0
LRC check sum:8-bit check sum consists of 2 ASCII codes
END 1END 0
END characters:END 1 = CR (0DH), END 0 = LF (0AH)
RTU mode:
START A silent interval of more than 10 msADR Communication address:
8-bit addressCMD Command code:
8-bit commandDATA (n-1)
…….DATA 0
Contents of data:
n×8-bit data, n<=25
CRC CHK LowCRC CHK High
CRC check sum:
16-bit check sum consists of 2 8-bit charactersEND A silent interval of more than 10 ms
3.3 ADR (Communication Address)
Valid communication addresses are in the range of 0 to 254. Communication address equals to 0 means broadcast to all AC drives (AMD), in this case, the AMD will not reply any message to the master device. For example, communication to AMD with address 16 decimal:ASCII mode: (ADR 1, ADR 0)=’1’,’0’ => ‘1’=31H, ‘0’=30HRTU mode: (ADR)=10H
3.4 CMD (Command code) and DATA (data characters)
The format of data characters depends on the command code. The available command codes are described as followed: Command code: 03H, read N words. The maximum value of N is 12. For example, reading continuous 2 words from starting address 2102H of AMD with address 01H.
CRC CHK Low 86H CRC CHK Low 86HCRC CHK High 22H CRC CHK High 22H
3.5 CHK (check sum)
ASCII mód:
LRC (Longitudinal Redundancy Check) is calculated by summing up, module 256, the values of the bytes from ADR1 to last data character then calculating the hexadecimal representation of the 2’s-complement negation of the sum.
For example, reading 1 word from address 0401H of the AC drive with address 01HSTX ‘:’
01H+03H+04H+01H+00H+01H=0AH, the 2’s-complement negation of 0AH is F6H.
RTU mód:ADR 01HCMD 03H
Starting address 21H02H
Number of data
(count by word)
00H02H
CRC CHK Low 6FHCRC CHK High F7H
CRC (Cyclical Redundancy Check) is calculated by the following steps:
Step 1: Load a 16-bit register (called CRC register) with FFFFH.
Step 2: Exclusive OR the first 8-bit byte of the command message with the low order byte of the 16-bit CRC register, putting the result in the CRC register.
Step 3: Shift the CRC register one bit to the right with MSB zero filling. Extract and examine the LSB.
Step 4: If the LSB of CRC register is 0, repeat step 3, else Exclusive or the CRC register
5-53
VFD-M Sorozat
with the polynomial value A001H.
Step 5: Repeat step 3 and 4 until eight shifts have been performed. When this is done, a complete 8-bit byte will have been processed.
Step 6: Repeat steps 2 to 5 for the next 8-bit byte of the command message.
Continue doing this until all bytes have been processed. The final contents of the CRC register are the CRC value. When transmitting the CRC value in the message, the upper and lower bytes of the CRC value must be swapped, i.e. the lower order byte will be transmitted first.The following is an example of CRC generation using C language. The function takes two arguments:
Unsigned char* data a pointer to the message buffer Unsigned char length the quantity of bytes in the message buffer
The function returns the CRC value as a type of unsigned integer.
The contents of available addresses are shown as below:Tartalom Cím FunkcióAC drive
Parameters00nnH 00 means parameter group, nn means parameter number, for
example, the address of Pr.100 is 0064H. Referencing to chapter 5 for the function of each parameter. When reading parameter by command code 03H, only one parameter can be read at one time.
Parancs
Olvasás/Írás
2000H Bit 0-1 00: Nincs funkció
01: Stop 10: Indítás 11: Léptetés + Indítás
Bit 2-3 LefoglalvaBit 4-5 00: Nincs funkció
01: ELŐRE10: HÁTRA11: Irányváltás
Bit 6-15 Lefoglalva2001H Frekvencia parancs 2002H Bit 0 1: EF (Külső hiba) bekapcsolva
Bit 1 1: Reset – Minden alaphelyzetbe áll visszaBit 2-15 Lefoglalva
5-55
VFD-M Sorozat
Tartalom Cím FunkcióÁllapot kijelzés – csak olvasásra
2100H Hibakód:
00: Nem történt hiba01: Túláram (oc)03: Túlmelegedés (oH)04: Inverter túlterhelés (oL)05: Motor túlterhelés (oL1)06: Külső hiba (EF)07: CPU hiba (cF1)08: CPU vagy analóg áramköri hiba (cF3)09: Hardware védelmi hiba (HPF)10: Az áramerősség x2 túllépte a névleges áramot
gyorsításkor (ocA)11: Az áramerősség x2 túllépte a névleges áramot lassításkor
(ocd)12: Az áramerősség x2 túllépte a névleges áramot készenléti
The following is a simple example of how to write a communication program for Modbus ASCII mode on a PC by C language.
#include<stdio.h>#include<dos.h>#include<conio.h>#include<process.h>#define PORT 0x03F8 /* the address of COM1 *//* the address offset value relative to COM1 */#define THR 0x0000#define RDR 0x0000#define BRDL 0x0000#define IER 0x0001#define BRDH 0x0001#define LCR 0x0003#define MCR 0x0004#define LSR 0x0005#define MSR 0x0006unsigned char rdat[60];/* read 2 data from address 2102H of AC drive with address 1 */ unsigned char tdat[60]=':','0','1','0','3','2','1','0',’2', '0','0','0','2','D','7','\r','\n'; void main() int i; outportb(PORT+MCR,0x08); /* interrupt enable */ outportb(PORT+IER,0x01); /* interrupt as data in */ outportb(PORT+LCR,(inportb(PORT+LCR) | 0x80)); /* the BRDL/BRDH can be access as LCR.b7==1 */ outportb(PORT+BRDL,12); /* set baudrate=9600, 12=115200/9600*/ outportb(PORT+BRDH,0x00); outportb(PORT+LCR,0x06); /* set protocol, <7,N,2>=06H<7,E,1>=1AH, <7,O,1>=0AH<8,N,2>=07H, <8,E,1>=1BH<8,O,1>=0BH */ for(i=0;i<=16;i++) while(!(inportb(PORT+LSR) & 0x20)); /* wait until THR empty */ outportb(PORT+THR,tdat[i]); /* send data to THR */
5-57
VFD-M Sorozat
i=0; while(!kbhit()) if(inportb(PORT+LSR) & 0x01) /* b0==1, read data ready */ rdat[i++]=inportb(PORT+RDR); /* read data form RDR */
Pr.93 Accel 1 to Accel 2 Frequency Transition Factory Setting: 0.00Pr.94 Decel 1 to Decel 2 Frequency Transition Factory Setting: 0.00
Settings 0.01 to 400.0 Hz Unit: 0.10 Hz 0.00 disable
This function can be used to set the switch time of Accel/Decel 1 and Accel/Decel 2 by this parameter without external terminals. The priority of this parameter is higher than the time of Accel/Decel 1 and Accel/Decel 2.
Ha az automatikus energiatakarékos üzemmód be van kapcsolva a frekvenciaváltó Gyorsításkor / Lassításkor maximális feszültségen dolgozik. Állandó sebességnél viszont az inverter kiszámolja az optimális kimenő feszültséget a terhelés számára. Ezzel akár 30% -os különbséget is elérhetünk a maximális kimenő feszültséghez képes. Ennek a funkciónak a használatát nem javasoljuk olyan helyeken, ahol a terhelés állandóan változik vagy a hajtás a határértékre van méretezve, mert így a funkció állandóan ki – be kapcsol és nagyon kevés lesz az energia megtakarítás.
With energy-saving enabled, thedrive automatically adjust the outputvoltage based on the output powerlevel. The maximum output voltagereduction is 30%.
Pr.96 Count Down Completion Factory Setting: 00 Settings 00 to 9999
This parameter defines the terminal count value for the VFD-M internal counter. The counter can be incremented by a low-to-high transition on a selected Multi-Function Input Terminal: M1 or M2. Upon completion of the count, if Pr.45 is programmed to 13, the Multi-Function Output Terminal (MO1) will be closed. If Pr.46 is programmed to 13, the Multi-Function Relay Contact RA, RB, RC will be closed.
Pr.97 Preset Count Down Completion Factory Setting: 00 Settings 00 to 9999
This parameter sets a preliminary count value for the internal counter. The counter can be incremented by a low-to-high transition on one of the programmed Multi-Function Input Terminals: M1 or M2. The count starts at 01. When it reaches the preliminary count value and the selected Multi-Function Output Terminal will be closed (Pr.45 = 14). Preliminary Count can be used to initiate an external event before the “terminal count” is reached. (See Pr.38, 39, 40, 41, 42, 45, and 46 for further details.)
Pr.98 A bekapcsolástól számított összes idő számolása (napok) Csak olvasásra Beállítás 00 - 65535 napokPr.99 A bekapcsolástól számított összes idő számolása
(percben) Csak olvasásra
Beállítás 00 - 1440 percek
5-59
VFD-M Sorozat
Pr.100 Software Verzió Csak olvasásra
Ez a paraméter megmutatja a frekvenciaváltón lévő szoftver verzió adatait. Ez az adat csak kiolvasható - nem állítható át.
03 Automatikus gyorsítás / lassítás04 Automatikus gyorsítás / lassítás (Kérlek nézd át a Pr.10 – Pr.13 ig a
paramétereket az idők beállításához)
Ha ez a paraméter 03 –ra van állítva, az inverter a leggyorsabban és legsimábban fogja a motor Gyorsítani / Lassítani, melyhez automatikus önmagának hozzáigazítja az időket.
Ez a paraméter 5 típusú möködést határozhat meg:
00 Linear acceleration and deceleration (operation by Pr.10, Pr.11, or Pr.12, Pr.13 acceleration/deceleration time)
01 Automatic acceleration, linear deceleration (Operation by automatic acceleration, Pr.11 or Pr.13 deceleration time).
02
03
04
Linear acceleration and automatic deceleration (Operation by automatic deceleration time, Pr.10 or Pr.12 acceleration time).
Automatic acceleration, deceleration (Operation by AC drive auto adjustable control)
If this parameter is set to 04, Accel/Decel time will be equal to or more than parameter Pr.10 ~Pr.13.
This parameter is not suitable for using with braking unit.
AVR function automatically regulates the AC drive output voltage to the Maximum Output Voltage (Pr.03). For instance, if Pr.03 is set at 200 VAC and the input voltage is at 200V to 264VAC, then the Maximum Output Voltage will automatically be regarded to 200 VAC.
Without AVR function, the Maximum Output Voltage may vary between 180V to 264VAC, due to the input voltage varying between 180V to 264 VAC.
Selecting program value 2 enables the AVR function and also disables the AVR function during deceleration. This offers a quicker deceleration.
Pr.103 Auto-Tuning - Motor paraméterezés Alaphelyzet: 00 Beállítás 00 Tiltva
01 Auto tuning R1 02 Auto tuning R1 + nincs terhelési tesz
Ha a 02 re állítod, akkor a motoron nem lehet terhelés alatt.
Pr.104 R1 Érték Factory Setting: 00 Beállítás 00 - 65535mΩ
This parameter can be used to set the resistor value of motor. The resistor value can be input by this parameter or set by Pr. 103.
Example: The rated speed of 4 poles/3 φ/ 60Hz/ 220V on the nameplate is 1710RPM. The rated slip is 60-(1710/(120/P))=3Hz. (P is the polar number of motor)
5-61
VFD-M Sorozat
Pr.107 Vector Voltage Filter Factory Setting: 10 Settings 5 to 9999 Unit: 2msPr.108 Vector Slip Compensation Filter Factory Setting: 50 Settings 25 to 9999 Unit: 2ms
This parameter is the low-pass filter in the vector control.
Example: Pr. 107 = 10 X 2ms =20ms, Pr. 108 = 50 X 2 ms =100ms.
Pr.109 Selection for Zero Speed Control Factory Setting: 00 Settings 00 No output
01 Control by DC voltage
This parameter is used to select the output method in zero speed. If it is set to 01, it will use the voltage set in Pr.110 to be holding torque.
Pr.110 Voltage of Zero Speed Control Factory Setting: 5.0 Settings 0.0 to 20.0 % of Max. output voltage (Pr.05) Unit: 0.1%
This parameter should be used with Pr.109.
Example: if Pr.05 = 100 and this parameter is set to 20.0, the level of output voltage is 100 X 20.0% = 20.
Pr.111 Lassítási S-görbe Factory Setting: 00
Settings 00 to 07
This parameter can be set to select a deceleration S-curve. The deceleration S curve is independent of Pr.14. When Pr.111=0, then Pr.14 sets the deceleration S-curve.
Note: From the diagram shown below, the original setting accel/decel time will be for reference when the function of the S-curve is enabled. The actual accel/decel time will be determined based on the S-curve selected (1 to 7).
Pr.112 External Terminal Scanning Time Factory Setting: 01 Settings 01 to 20 Unit: 2msec This function can screen the signal on I/O terminals when the CPU malfunctions due to
external transients. Factory setting of the scanning time is 2msec and if it is set to 02, the scanning time is 2 x 2 =4 msec.
01 Continue operation after fault speed search from speed reference02 Continue operation after fault speed search from Minimum speed
This parameter is used to select the restart method when over current, over voltage and B.B.
Pr. 114 Hűtő ventillátor működési módja Alaphelyzet: 02
Beállítás 00 A ventillátor az inverter leállása után 1 min. –nel kikapcsol01 Csak az inverter tényleges működés alatt forog02 Mindig működik03 Lefoglalva
Pr. 115 PID Set Point Selection Factory Setting: 00 Settings 00 Disable
01 Keypad (based on Pr.00 setting)02 AVI1 (external 0-10V)03 AVI2 (external 4-20mA)04 PID set point (Pr.125)
PPr.117
IPr.118
DPr.119
Pr.120
AVI( )ACI( )
Pr.128~Pr.130Pr.131~Pr.133 Pr.116
+
-
+
+
Pr.135LPF
Targeted value
Upper Bound of Integral Value Pr.122
+ Limit of PIDOutputFrequency
One TimeDelay Pr.121
Definition of Detection Value
FrequencyCommand
Selection ofDetection value
5-63
VFD-M Sorozat
Pr. 116 PID Visszacsatolási terminál kiválasztása Factory Setting: 00 Settings 00 Input positive PID feedback, PV from AVI (0 to 10V)
01 Input negative PID feedback, PV from AVI (0 to 10V)02 Input positive PID feedback, PV from ACI (4 to 20mA)03 Input negative PID feedback, PV from ACI (4 to 20mA)
Select an input terminal to serve as the PID feedback position. Please verify the feedback position is different from the Frequency Set Point position.
Negative feedback = positive targeted value – detective value. Positive feedback = negative targeted value + detective value.
Pr. 117 Arányossági Gain (P) Factory Setting: 1.0 Settings 0.0 to 10.0
This parameter determines the gain of the feedback loop. If the gain is large, the response will be strong and immediate (If the gain is too large, vibration may occur). If the gain is small, the response will be weak and slow.
If I=0.0 and D=0.0, it is only used for proportional control.
Pr. 118 Integrális idő (I) Factory Setting: 1.00 Settings 0.01 to 100.00 sec Unit: 0.01sec
0.00 disable
This parameter determines the speed of response for the PID feedback loop. If the integral time is long, the response will be slow. If the integral time is short, the response will be quick. Be careful not to set (I) too small, since a rapid response may cause oscillation in the PID loop.
Pr. 119 Differenciális idő (D) Factory Setting: 0.00 Settings 0.00 to 1.00 sec Unit: 0.01sec
This parameter determines the damping effect for the PID feedback loop. If the differential time is long, any oscillation will quickly subside. If the differential time is short, the oscillation will subside slowly.
Pr. 120 Integration’s Upper Bound Frequency Factory Setting: 100 % Settings 00 to 100 %
This parameter determines the integration’s upper frequency limit while operating in the PID feedback loop. (Limit = Pr.03×Pr.120). During a fast Integration response, it is possible for the frequency to spike beyond a reasonable point. This parameter will limit this frequency spike.
Pr. 121 Egyszeri késleltetés Factory Setting: 0.0 Settings 0.0 to 2.5 sec Unit: 0.1sec
0.0 disable
PI Control: controlled by the P action only, and thus, the deviation cannot be eliminated entirely. To eliminate residual deviations, the P + I control will generally be utilized. And when the PI control is utilized, it could eliminate the deviation incurred by the targeted value changes and the constant external interferences. However, if the I action is excessively powerful, it will delay the responding toward the swift variation. The P action could be used solely on the loading system that possesses the integral components.
PD Control: when deviation occurred, the system will immediately generate some operation load that is greater than the load generated single handedly by the D action to restrain the increment of the deviation. If the deviation is small, the effectiveness of the P action will be decreasing as well. The control objects include occasions with integral component loads, which are controlled by the P action only, and sometimes, if the integral component is functioning, the whole system will be vibrating. On such occasions, in order to make the P action’s vibration subsiding and the system stabilizing, the PD control could be utilized. In other words, this control is good for use with loadings with no braking functions over the processes.
PID Control: Utilize the I action to eliminate the deviation and the D action to restrain the vibration, thereafter, combine with the P action to construct the PID control. Use of the PID method could obtain a control process with no deviations, high accuracies and a stable system.
Pr. 122 PID Frequency Output Command limit Factory Setting: 00 Settings 00 to 110 %
This parameter determines the limit of the PID Command frequency. If this parameter is set to 20%, then the maximum output frequency while in the PID operation will be (20% x Pr.01-00).
5-65
VFD-M Sorozat
Pr. 123 Visszacsatolási jel felismerési ideje Factory Setting: 60.0 Settings 0.1 to 3600 sec Unit: 0.1sec
0.0 disable
This parameter defines the detection time for the loss of a feedback analog signal. The drive will follow the operating procedure programmed in Pr.124 if the feedback signal is lost for more than the time set in Pr.123.
Pr. 124 Feedback Signal Fault Treatment Factory Setting: 00 Settings 00 Warn and RAMP to stop
01 Warn and COAST to stop
This parameter selects the operation of the drive upon a loss of PID feedback signal.
Pr. 125 PID beállítási érték forrása Factory Setting: 0.00 Settings 0.00 to 400.0Hz
This parameter is used to set the position of target value when Pr. 115 is set to 04.
Pr. 126 PID Offset Level Factory Setting: 10.0 Settings 1.0 to 50.0 %
This parameter is used to set the offset between target value and feedback.
Pr. 127 Detection Time of PID Offset Factory Setting: 5.0 Settings 0.1 to 300.0 sec
This parameter is used to set the detection time of PID offset.
Pr. 128 Minimum Referenciaérték Factory Setting: 0.0 Settings 0.0 to 10.0 V Unit: 0.1V
This parameter is used to set the AVI input voltage that corresponds to minimum frequency.
Pr. 129 Maximális Referenciaérték Factory Setting: 10.0 Settings 0.0 to 10.0 V
This parameter is used to set the AVI input voltage that corresponds to maximum frequency.
Pr. 130 Inverter referencia jel AVI (0-10V) Alaphelyzet: 00 Settings 00 Not Inverted
01 Inverted
If this parameter is set to 01, 0V corresponds to 0Hz in Pr.128 and Pr.129 will become to 0V corresponds to 60Hz.
Pr. 131 Minimum Referencia érték (0-20mA) Factory Setting: 4.0 Beállítás 0.0 - 20.0mA Unit: 0.1mA
This parameter is used to set the ACI input frequency that corresponds to minimum frequency.
Pr. 132 Maximális Referenciaérték (0-20mA) Factory Setting: 20.0 Settings 0.0 to 20.0mA Unit: 0.1mA
This parameter is used to set the ACI input frequency that corresponds to maximum frequency.
Pr. 133 Inverts Reference Signal (0-20mA) Factory Setting: 00 Settings 00 Not Inverted
01 Inverted
If this parameter is set to 01, 4mA corresponds to 0Hz in Pr.132 and Pr.133 will become to 0mA corresponds to 60Hz.
The main function of Pr.128-Pr.133 is for users to define the range of output frequency according to feedback sensor when setting analog frequency or PID feedback control. For example, if feedback sensor is 4mA-20mA but the output frequency corresponds to AC drive that user need is 5mA-18mA, at this time, user can set Pr.131 to 5mA and Pr.132 to 18mA.
5-67
VFD-M Sorozat
Pr. 134 Analog Input Delay Filter for Set Point Factory Setting: 50 Settings 00 to 9999 Unit: 2msPr. 135 Analog Input Delay Filter for Feedback Signal Factory Setting: 5 Settings 00 to 9999 Unit: 2ms
These two parameters are used to set the analog input delay filter in set point or feedback signal.
These parameters determine sleep functions of the AC drive. If the command frequency falls below the sleep frequency, for the specified time in Pr.136, then the drive will shut off the output and wait until the command frequency rises above Pr.138. Please see the below diagram.
Pr. 138
Pr. 137
Pr. 136
0Hz
Frequency Command
Actual output frequency
Sleep Period
SleepFrequency
Wake UpFrequency
Pr. 139 Treatment for Counter Attained Factory Setting: 00 Settings 00 Continue Operation
01 Stop Immediately and display E.F.
This parameter is used to set the treatment after the counter attains the value that set in Pr.96.
Pr. 140 External Up/Down Selection Factory Setting: 00
Settings 00 By Fixed Mode (Like keypad mode)01 By Accel or Decel Time
This parameter is used to the set the up/down frequency mode when Pr.39-Pr.42 is set to 14 and 15. If this parameter is set to 01, up/down frequency is activated according to the time of acceleration/deceleration and contact close.
Pr. 141 Save the Set Point of Frequency Factory Setting: 01 Settings 00 Not Save
01 Save
This parameter is used to set if it needs to save frequency setting before power off.
Pr. 142 The Second Source of Frequency Command Factory Setting: 00 Settings 00 Keypad Up/Down
01 Keypad Potentiometer02 AVI (0-10V)03 ACI (4-20mA)04 RS485
This parameter is used when Pr.39-Pr.42 is set to 28.
Pr. 143 Software Braking Level Unit: 0V Settings 230V series 370 to 450 Vdc Factory setting: 380.0
460V series 740 to 900 Vdc Factory setting: 760.0
This parameter sets the level for dynamic braking to enable. The value must be higher than the steady state DC-BUS voltage, otherwise the braking transistor will have a 100% duty. At 100% duty the transistor and resistor will most likely fail.
Pr. 144 Accumulative Motor Operation Day Read Only Settings 00-65535 DaysPr. 145 Accumulative Motor Operation Time (Min.) Read Only Settings 00-1440 Minutes
These parameters display the accumulative time of motor operation. It won’t reset to zero due to parameter reset to factory and won’t re-calculate due to exceed 65535 days.
5-69
VFD-M Sorozat
Pr. 146 Line Start Lockout Factory Setting: 00 Settings 00 Disable
01 Enable
When enabled, the AC drive will not start when powered up with run commands applied. To start in Line Start Lockout mode, the AC drive must see the run command go from stop to run after power up. When Line Start Lockout is disable (also known as Auto-Start), the drive will start when powered-up with run commands applied.
Pr. 147 Decimal Number of Accel / Decel Time Factory Setting: 00 Settings 00 One Decimal
01 Two Decimals
It is used to set the decimal number of accel/decel time. It can be used for Acceleration / Deceleration Time 1, Acceleration / Deceleration Time 2 and JOG Acceleration / Deceleration Time.
Pr. 148 Motor pólus számainak beállítása Factory Setting: 04 Beállíáts 02 - 20Pr. 149 Gear Ratio for Simple Index Function Factory Setting: 200 Settings 4 to 1000Pr. 150 Index Angle for Simple Index Function Factory Setting: 180.0 Settings 00.0 to 360.0Pr. 151 Deceleration Time for Simple Index Function Factory Setting: 0.00 Settings 0.00 to 100.00 sec
0.00 Disable
This parameter should be used with Pr. 39-Pr.42 (setting 31).Example:
Pr. 152 Skip Frequency Width Alaphelyzet: 0.00Beállítás 0.00 to 400.00Hz
Pr. 153 Bias Frequency Width Alaphelyzet: 0.00Beállítás 0.00 to 400.00Hz
Frequency of ∆ top point Fup= master frequency F + Pr.152 + Pr.153.
Frequency of ∆ down point Fdown= master frequency F – Pr.152 – Pr.153.
5-71
VFD-M Sorozat
Fup
Fdown
Pr.10, 12
Pr.11, 13
Pr.152
MasterFrequency(F)
Double Pr. 153
Pr. 154 Lefoglalva
Pr. 155 Kompenzációs állandó, motor stabilitási problémákhoz. Alaphelyzet: 0.0 Beállítás 0.1 - 5.0 (javasolt 2.0)
0.0 Kikapcsolva
Ezzel a paraméterrel javítani tudjuk a nem egyenletes áramerősség problémákat. ( Nagyobb frekvenciáknál, ezt a parmétert akár 0.0 -ra is állíthatod, és növeld a Pr 155. paramétert, ha 30HP –s vagy nagyobb motorteljesítményt használsz alacsony frekvencián (javasolt érték 2.0).
A modern frekvenciaváltók folyamatos működésű elektronikus technológiát tartalmaznak, ennek ellenére a meghibásodás elkerülése érdekébe szükségesnek tartjuk, hogy időszakosan (havonta) elvégezz egy megelőző karbantartás is. Ezzel természetesen a frekvenciaváltó élettartama is megnő. Minden alkalommal az ellenőrzés előtt, légy szíves kapcsold le az invertert a hálózatról. Várj legalább 10 másodpercet a kijelző kialvása után, és ellenőrizd DC voltmérővel a B1 és a GND között a feszültséget.
6.1 Ismétlődő ellenőrzések
Alap ellenőrzések az esetleges abnormális üzem felismeréséhez:
1. Akkor is, ha a motor megfelelően működik.
2. Akkor is, ha a működési környezet normális.
3. Akkor is, ha a hűtő rendszer tökéletes.
4. Akkor, ha nem szokványos rezgés vagy hang hallatszik működés közben.
5. Akkor, ha a motor túlmelegedik működés közben.
6. Mindig ellenőrizd, a bementi feszültséget voltmérővel.
6.2 Ismétlődő karbantartás
! FIGYELEM! Kapcsold le a hálózatról, mielőtt hozzákezdenél!
1. Húzd meg mindig a rezgésből vagy hőmérséklet ingadozás okából kilazult csavarokat az inverteren.
2. Cseréld ki a korrodált vagy sérült csavarokat, kábeleket.
3. Ellenőrizd a szigetelések ellenállását Meg-Ohm mérővel.4. Gyakran ellenőrizd, és ha kell, cseréld a kondenzátorokat és reléket.5. Ha az invertert hosszú ideig folyamatosan használod, akkor kapcsold le mindig a
hálózatról legalább kétévente egyszer, és ellenőrizd, hogy minden megfelelően működik-e. Hogy ténylegesen le tudd ellenőrizni az invertert, kapcsold le a motort és helyezd áram alá az invertert legalább 5 órán keresztül vagy tovább, mielőtt újra üzemszerűen akarod használni
6. Tisztítsd le minden szennyeződéstől az invertert. Takarításnál kérlek, figyelj oda jobban a szellőző nyílásokra és PCB-re is. Mindig tartsd tisztán ezeket a részeket, mert különben a hosszútávú üzemeltetés közben ezek problémát okozhatnak.
kiadásának forrása00: Frekvencia parancs kiadása a digitalis vezérlőn keresztül (LC-M02E)01: Frekvencia parancs kiadása a beépített potencióméteren keresztül02: Frekvencia parancs kiadása a
0 - 10 V bemeneten keresztül 03: Frekvencia parancs kiadása a
4 -20mA bemeneten keresztül04: Frekvencia parancs kiadása az RS-485 –ös kommunikációs interfészen keresztül
00
Pr.01 Vezérlési parancs kadásának helye
00: Vezérlési prancsok kiadása a digitalis vezérlőről01: Vezérlési parancsok kiadása külső vezérlőről, a beépített vezérlő STOP gombja aktív. 02: Vezérlési parancsok kiadása külső vezérlőről, a beépített vezérlő STOP gombja nem aktív. 03: Vezérlési parancsok kiadása az RS 485 –ös kommunikációs interfészen keresztül, STOP aktív 04: Vezérlési parancsok kiadása az RS 485 –ös kommunikációs interfészen keresztül, STOP nem aktív
01: WG OFF (N.O.) (it is enable during running)02: WG OFF (N.C.) (it is enable during running)03: Külső hiba (normálisan nyitott) N.O. 04: Külső hiba (normálisan zárt) N.C05: RESET06: Több lépcsős sebesség parancs 107: Több lépcsős sebesség parancs 208: Több lépcsős sebesség parancs 309: Jog működés10: Accel/Decel Speed Inhibit 11: First or Second Accel/Decel Time 12: Base-block (B.B.) (N.O)
13: Base-block (B.B.) (N.C)14: Frekvencia növelés15: Frekvencia csökkentés16: PLC Program futtatása17: PLC program pillanat állj
18: Counter Trigger Signal19: Számláló RESET
20: Nincs funkció21: RESET parancs (N.C)22: Vezérlési hely: I/O23: Vezérlési hely: Digitális kijelző24: Vezérlési hely: Kommunikáció25: Paraméter lezárás (Írás tiltva, Olvasás mindig 0)26: PID Tiltás (N.O.)27: PID Tiltás (N.C.)28: Frekvencia parancs kiadásának második forrása29: ELŐRE (Kontaktus nyitva) / HÁTRA (Kontaktus zárva)30: One-Shot PLC Run31: Index input signal32: Counter Incremented by Drive Output Frequency00: Analóg Frekvencia mérő (0 – Maximális kimeneti frekvenciáig)
00
Pr.44 Analóg kimenet erősítés
01: Analog áramerőség mérő (0 - 250% of the rated AC drive current)02: Visszacsatolási jel (0 - 100%)03: Kimenő teljesítmény (0 - 100%)00 - 200 %
100
00: Inverter működési állapot jelzése 00
01: Maximum Output Frequency Attained02: Zéró Sebesség03: Túl-nyomaték felismerése04: Base-Block (B.B) jelzés05: Alacsony feszültség felismerése06: AC Inverter működési mód07: Hibajelzés08: Kívánt frekvencia elérve 09: PLC Program fut
10: PLC Program Lépés végrehajtva 11: PLC Program Végrehajtva 12: PLC működési mód szünetel13: A terminál számlálási értéke elérve14: Preliminary Counter Value Attained15: Warning (PID feedback loss, communication error)16: Below the Desired Frequency17: PID supervision18: Over voltage supervision19: Over Heat supervision20: Over Current stall supervision21: Over voltage stall supervision22: Előre parancs23: Hátra parancs24: Zéró sebesség (Stop – megállás is)0.00 - 400.0 Hz
Pr.58 Electronic Thermal Overload Relay 01: Inverter Motor (kényszerhűtéses motor)
02
Pr.59 Elektronikus hő karakterisztika
02: Nem aktív30 - 300 sec00: Túl-nyomaték felismerés tiltva 60
Pr.60 Túl-nyomaték felismerési mód
01: Enabled during constant speed operation and continues until the Continuous Time Limit (Pr.62) is
00
Pr.61 Túl-nyomaték felismerési szint
02: Enabled during constant speed operation and halted after detection.03: Enabled during acceleration and continues before Continuous Output Time Limit (Pr.62) is reached.04: Enabled during acceleration and halted after Over-Torque detection.30 - 200 %
02: Folytatja a működést az utolsó Frekvencia parancs értékén00: Írja ki az inverter kimeneti Frekvenciáját (Hz)01: Írja ki az ügyfél specifikus kimeneti Frekvenciát H*Pr.65
06
(Pr.65
“K” állandó
02: Kimenő Feszültség (E)
03: DC Bus Feszültség (u_)
04: PV (i)05: Írja ki a belső számláló értékét (c)06: Írja ki a beállítási Frekvenciát
(F v. o=%)07: Írja ki a paraméter beállítás kódját (Pr.00)Lefoglalva
09: Kimeneti áramerősség (A)
10: Írja ki a program működését (0.xxx), Fwd, vagy Rev0.01 - 160.0
02: Programciklusok folyamatos végrehajtása03: Egy programciklus lépésről – lépésre történő végrehajtása04: Egy programciklus lépésről – lépésre történő végrehajtása00 – 127
02: AVI 1 (külső 0-10V)03: AVI 2 (külső 4-20mA)04: PID et point (Pr.125)00: Input positive PID feedback, PV from AVI (0 to 10V)01: Bemenet negatív PID visszacsatolás, PV az AVI bemenetről (0 - 10V)
ika Vezérlési rendszer SPWM (Szinuszos Pulzus modulációval) (vivő frekvencia 1kHz~15kHz)/
Szenzor nélküli vektoros vezérlésKimeneti frekvencia tartomány 0.1HzTúlterhelési tartomány 150% a névleges áramfelvételének 1 percen keresztülGyorsítási/Lassítási idő 0.1 - 600 másodperc (Független Gyorsítási/Lassítási idő állítás)Nyomaték karakterisztika Automatikus nyomatéktartás, automatikus szlipkompenzáció,
Védelem Öndiagnosztika, Túlfeszültség, Túláram, Alacsonyfeszültség, Túlterhelés, Túlmelegedés, Külső hiba, Elektronikus hő, földelési hiba.
Hűtési eljárás Kényszerhűtés (3HP)
Körn
yeze
t Telepítési környezet Max. 1000 m vagy alatta, tartsa távol a korrózív gázoktól, folyadéktól és portólSzennyeződési osztály 2Környezeti hőmérséklet -10°C - 50°C
-10°C - 40°C - 5. 5 kW –tól és feletteMűködési hőmérséklet -20°C to 60°CKörnyezeti páratartalom 90% alatti (nem mártható vízbe)Rezgés 9. 80665 m/s2 (1G) Kevesebb, mint 20Hz, 5. 88m/s2 (0. 6G) 20 - 50Hz
Megjegyzés: A jelbemenetre ne kösse a háromfázisú hálózatot.
A fent felsorolt termékek megfelelnek a 73/23/ECC - elektromos berendezések meghatározott feszültséghatárán belül - és 93/68/EEC nemzetközi direktívának. Ezeknél a direktívák meghatározásánál a következő szabványokat vették figyelembe:
EN 50178
A következő gyártó / importáló felelős ezért a kinyilatkoztatásért:
Delta Electronics, Inc. (Cég név)
31-1, Shien Pan Road, Kuei San Industrial Zone, Taoyuan Shien, Taiwan 333 (Cég címe)
D-1
VFD-M Sorozat
DELTA ELECTRONICS, INC.
EC Megfelelőségi bizonylataz elektromágnese kompatibilitásra a 73/23/EEC és a 93/68/EEC
A fent felsorolt termékek megfelelnek a 73/23/ECC és 93/68/EEC nemzetközi direktívában előírt elektromágneses megfelelősségnek. Ezeknél a direktívák meghatározásánál a következő szabványokat alkalmazták:
EN61800-3, EN55011, EN50081-2, EN50082-2, EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8 A következő gyártó / importőr felelős a kinyilatkoztatásért:
Delta Electronics, Inc. (Cég név)
31-1, Shien Pan Road, Kuei San Industrial Zone, Taoyuan Shien, Taiwan 333 (Cég címe)