1 Fall 2005 Virtual Circuit Switching and ATM: Asynchronous Transfer Mode Qutaibah Malluhi CSE Department Qatar University.

1

Fall 2005

Virtual Circuit Switching andATM: Asynchronous Transfer

Mode

Qutaibah MalluhiCSE DepartmentQatar University

2

Types of WANs

Dedicated-circuit Networks

Switched Networks– Circuit-switched and packet-switched Networks

» Virtual Circuit approach

Local Loop Technologies– E.g., DSL, Cable Modem

Wireless WAN (Cellular Network)

3

Dedicated Circuit Networks

Lease circuits from common carriers All connections are point-to-point. A flat fee per month. Unlimited use of the circuit Several standards specified by the telephone

industry in each country– T-Series Carrier Services (US)

» T1: 1.5 Mpbs, T2: 6.312 Mbps, T3: 44.736 Mbps

– E Services (Europe & Qatar)» E1: 2.048 Mbps, E2: 8.448 Mbps, E2 : 34.368 Mbps

– Other high-speed Services » E.g., Optical Carrier (OC) Standard:

51.840 Mbps (OC-1) to 2,488.320 Mbps (OC-48)

4

Switched Networks

Circuit-switched networks – Form a dedicated connection (circuit) between two points

– Guaranteed capacity but high-cost (cost is fixed and is independent of the traffic)

– Circuit-switched networks operates over the PSTN (public switched telephone network)

– No link sharing

– E.g. Plain Old Telephone Service (POTS) and Integrated Services Digital Network (ISDN)

Packet switched networks– Data divided into small packets. Each packet is sent

individually

– Link is shared by multiple transmissions

– E.g. IP datagram delivery

5

Packet Switching

Datagram Switching– Each packet contains the destination address and

sequence number to each packet– A route is independently chosen for EACH packet.– The packets may arrive out of sequence.– E.g., Ethernet, IP

Virtual Circuit Switching– Similar to dedicated circuits unlike circuit switching,

which is a physical layer technology, it is a Data link layer technology.

– A preplanned route is established before data transmission.

– All packets for one transmission take the same route– Each packet contains a virtual circuit identifier.– E.g. Frame Relay and ATM

6

32

1

Datagram

7

32

1

Virtual Circuit

8

VCI: Virtual Circuit Identifier

VCI is used to identify a virtual circuit between the sender and the receiver

A small number that has the switch scope Used by a frame between two switches VCI in a data frame changes from one switch to

another

9

Switch Forwarding Table

Has a table entry for each VC 4 columns: (In Port, In VCI), (Out VCI, Out Port) Maps an incoming (port, VCI) into an outgoing

(port, VCI)

10

Source-to-Destination Data Transfer

11

Communication Phases

Sender and receiver go through three phases– Setup

» create virtual circuit forwarding table entries

– Data transfer– Teardown

» Delete VC virtual circuit forwarding table entries

12

Types of Virtual Circuits

Permanent Virtual Circuit (PVC)– Forwarding table entries are setup manually by the

administrator– Like a point-to-point leased telephone circuit– No dialing is needed, circuit is always up and ready– Costly (pay even if you are not using it)

Switched Virtual Circuit (SVC)– Dynamic on-demand creation of connections– Exists when data is being transferred. Tear down when

session ends.– Connection (dialing) phase is required (Also called

Signaling)

13

SVC Setup Request

14

SVC Request Acknowledgement

15

ATM: Asynchronous Transfer Mode

16

Asynchronous Transfer Mode (ATM)

Designed by phone companies Single technology meant to handle

– Voice– Video– Data

Intended as LAN or WAN

17

ATM Characteristics

End-to-end (application to application)

Connection-oriented interface:– Establish “connection”– Send data– Teardown connection

Performance guarantees (statistical) Uses cell switching

18

ATM Switch

Building block of ATM network Connections to

– Computers—User-Network Interface (UNI)– Other ATM switches– Network-Network Interface

(NNI) Accepts and forwards cells

19

ATM Design Issues

Different traffic has different demands Variable packet size introduces more

jitter (variance in delivery time) Even sending at a constant rate,

contention can result jitter Small packets incur less jitter and

delay, but less efficient Large packets more efficient, delay

and jitter is more serious (packet loss)

20

ATM Cell

A cell network uses the cell as the basic unit of data exchange.

A cell is a small, fixed-sized block of information. Size chosen as compromise between voice

(small) and data (large)– 5 octet header– 48 octet payload

Note: size not optimal for any application

21

Variable Frame-Size vs. Cell Multiplexing

22

ATM Cell Switching

23

ATM Cell Formats

NNICell

UNICell

24

ATM Cell Format

GFC: Flow control – local flow control (user-to-network only). doesn't appear in

network-to-network interface VPI/VCI: virtual circuit identification

– together provide identification of the cell connection (see later)– Only difference between NNI and UNI cells is that NNI VPI is

a larger field PT - Payload type

– indicates the type of the cell (e.g. user data cell, resource management cell, operation and maintenance cell)

CLP: Cell Loss Priority– one bit specifying whether or not the cell can be dropped (e.g.

voice/video is loss tolerant) HEC - Header Error Control

– 8-bit CRC

25

Cell Forwarding

Virtual Circuit Switching Also label switching: Uses label in cell

– Label is used to identify the virtual circuit– Label is specified by the pair: Virtual Path

Identifier/Virtual Channel Identifier (VPI/VCI)

Like standard virtual circuit switching, VPI/VCI is rewritten at each switch

26

TP, VP and VC

TP: Transmission Path– Physical connection

VP: Virtual Path– specified by VPI– Set of connections

between two end devices– Path the VC follows

through the network VC: Virtual Circuit

– specified by VCI– All cells of the same

message follow the same VC

27

VPI/VCI: Identify a Virtual Connection

Virtual connection is defined by a pair: VPI/VCI

28

ATM Switch Forwarding/Rewriting

Forwarding Table

29

Example II Of VPI/VCI Rewriting

Sender uses VPI/VCI 3 Receiver uses VPI/VCI 6 Intermediate VPI/VCIs are established within

each switch

30

ATM Layers

Physical Layer– Can be one of several physical layer technologies (e.g.

SONET) ATM Layer

– Routing, traffic management, switching and multiplexing

– Receives 48 byte segment from AAL sublayers and transform it into a 53 byte cell

AAL: Application Adaptation Layer– Depend on type of application: data frames, stream of

bits, CBR

31

Application Adaptation Layers AAL1:

– Constant bit rate (CBR) – Example: audio

AAL2: – Variable bit rate (VBR)

» Example: video with adaptive encoding– Low bit rate and short packet traffic

» Audio, video, and fax AAL3/4:

– conventional packet switching with sequencing and error control

AAL5: – Used for sending data (not audio/video)– Simple and efficient adaptation layer– No sequencing: assumes cells corresponding to a message

travel sequentially– No error control: left to upper layers (e.g. TCP/IP)

32

ATM Quality Of Service

Specified when connection established Endpoint specifies

– Type of data transfer– Throughput desired– Maximum packet burst size– Maximum delay tolerated

33

Issues

More expensive than traditional LAN technology More connection setup time Cell tax (header/data ~= 10%) Need to specify service requirement at the

connection, some may not know which to specify Lack of efficient broadcast Complexity of QoS (Quality of Service): one can

specify the request, but hard to enforce it Assumption of homogeneity