wiring devices | decorative www.mkelectric.co.uk Elements Collection Technical 1 MK Elements Collection Installation The MK Elements Collection products consist of the main product module, complete with its’ support frame, plus a separate clip on frontplate. The product is mounted to the wall, after wiring, and the frontplate is clipped onto the frame. The frontplate is supplied separately to aid installation. 1. Ensure the depth of the back box is correct for the product and that it is fitted securely to the wall. 2. Install the cables in the normal way and, using the fixing screws supplied, mount the product, still minus its frontplate, to the wall. It is important the correct headed screws are used as any other may clash with the rear of the front plate. 3. Do not over tighten the screws, so as to prevent damage or distortion to the product or support frame. Adjust so the frame or module sits squarely on the wall. Footnote: Care should be taken to ensure product features such as snap fits are not blocked during installation or decorating, preventing correct fitting of frontplates (for example plaster, tile grout, paint etc). 1. Locate the top and bottom hooks on the back of the frontplate into the holes on the top and bottom of the module. 2. Gently push along the top edge of the frontplate followed by the bottom edge. Note: Ensure the correct frontplate is fitted to the correct module or frame 1. Carefully insert a 4mm screwdriver into the slots provided along the bottom edge frontplate. 2. Carefully twist the screwdriver and lift the frontplate away disengaging the snap fits.
28
Embed
1 Elements Collection Technical wiring devices decorative … Elements Collect… · 1 Elements Collection Technical MK Elements Collection Installation The MK Elements Collection
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
wiring devices | decorative www.mkelectric.co.uk
Elements Collection Technical1
MK Elements Collection
Installation
The MK Elements Collection products consist of the main product module, complete with its’ support frame, plus a separate clip on frontplate. The product is mounted to the wall, after wiring, and the frontplate is clipped onto the frame. The frontplate is supplied separately to aid installation.
1. Ensure the depth of the back box is correct for the product and that it is fitted securely to the wall.
2. Install the cables in the normal way and, using the fixing screws supplied, mount the product, still minus its frontplate, to the wall. It is important the correct headed screws are used as any other may clash with the rear of the front plate.
3. Do not over tighten the screws, so as to prevent damage or distortion to the product or support frame. Adjust so the frame or module sits squarely on the wall.
Footnote: Care should be taken to ensure product features such as snap fits are not blocked during installation or decorating, preventing correct fitting of frontplates (for example plaster, tile grout, paint etc).
1. Locate the top and bottom hooks on the back of the frontplate into the holes on the top and bottom of the module.
2. Gently push along the top edge of the frontplate followed by the bottom edge.
Note: Ensure the correct frontplate is fitted to the correct module or frame
1. Carefully insert a 4mm screwdriver into the slots provided along the bottom edge frontplate.
2. Carefully twist the screwdriver and lift the frontplate away disengaging the snap fits.
ELV Tungsten Halogen with Dimmable Electronic Transformer 35 – 500VA 35 – 300VA
Dimmable LED Driver*4-150W
(Max 5 LED drivers only)*4-120W
(Max 5 LED drivers only)
Note:
1. Do not use loads of different types on the same circuit.
2. Not suitable for use with any other load type.
3. *Neutral connection is required. It is recommended to connect neutral whenever possible to extend the load handling capability of the dimmer.
1-10V Dimmer K34499Rated Load 6AXMaximum number of ballasts 10
Neutral connection is mandatory on 1-10V Dimmer. Suitable for use with dimmable fluorescent or LED lighting which is driven by separate 0/1-10V control gear.
Suitable for use with 0/1-10V analogue dimmable ballast operating in accordance with IEC60929 annex E.
Note: This product is only suitable for use with ballasts which are the source of the control voltage. It is not suitable for any other load type.
A range of socket outlets designed for ease of installation and having all the advantageous design features of the Elements Collection.
The two gang switch socket and one gang unswitched socket are fitted with one earth terminal, the one gang switch socket is fitted with two earth terminals on a common busbar to provide a double earth facility for use when installations require a high integrity protective connection as specified within BS 7671: 2008.
The products can be quickly installed as replacements for existing 13 amp sockets or in a new installations (if suitable mounting box is in position).
Round pin socketsA range of round pin sockets is also available.
Standards and approvals
13A socket outlets comply with BS 1363 Part 2, MS589, SS145, SASO2203, IS411.
l 16 standard finishes
l Many more customised combinations of standard colours, materials and finishes available
l Bespoke colours, materials and finishes available via the Design Service
l Products with LED locators and indicators available
l 3 pin operated shutter
l Printed terminal markings on grey rear mouldings for clearer identification
l Top access, angled terminals make wiring easier and quicker
l 3mm minimum switch contact gap
l Double pole switching
l Additional electrical safety from neutral ‘make first’, ‘break last’ feature
l Switch contacts with silver contacts on both surfaces for good continuity
l Only one size of screwdriver required for installation
l Dual earth terminals for high integrity earthing on 1 Gang Switched Socket Outlet
l Backed out and captive terminal screws
Features
wiring devices | decorative www.mkelectric.co.uk
Elements Collection Technical7
13 Amp Socket Outlets
Installation
Elements socket outlets can be wall or bench mounted. Do not mount or use as a trailing socket or where they may be subject to excessive moisture or dampness.
Technical specification
Electrical
Voltage rating:250V a.c.
Current rating:13A
Terminal capacity:Live, neutral & earth3 x 2.5mm2
3 x 4mm2
2 x 6mm2 (stranded)
Physical
Ambient operating temperature:–5°C to +40°C(not to exceed an average of more than 25°C in any 24 hour period)
IP rating:IP2XD
Max. installation altitude:2000 metres
Elements 13A socket outlets comply with 13A socket outlets comply with BS 1363 Part 2, MS589, SS145, SASO2203, IS411
BOX TYPES
Flush Flush (for extra wiring space)
1 gang 866ZIC 877ZIC
2 gang 886ZIC 878ZIC
Footnote: Care should be taken to ensure product features such as snap fits are not blocked during installation or decorativng, preventing correct fitting of frontplates (for example plaster, tile grout, paint etc).
Round pin socket outlets comply with BS546, MS1577 and SS472
Description
A range of round pin socket outlets designed for ease of installation and having all the advantages and design features of the Elements Collection. These products can be quickly installed as replace ments for existing socket outlets or in new installations.
Installation
Elements socket outlets can be wall or bench mounted – do not mount or use as a trailing socket or where they may be subjected to excessive moisture or dampness.
Technical specification
Electrical
Voltage rating:250V a.c.
Terminal capacities:5 amp sockets (K34382):3 x 2.5mm2
3 x 4mm2 2 x 6mm2 (stranded)15 amp sockets (K34383):3 x 2.5mm2
2 x 4mm2
1 x 6mm2 (stranded)
Physical
Ambient operating temperature:–5°C to +40°C(not to exceed an average of more than 25°C in any 24 hour period)
IP rating:IP2XD
Max. installation altitude:2000 metres
l 3mm minimum switch contact gap
l Only one size of screwdriver required for installation
l 5 AMP Round Pin Socket Outlets available in 16 standard finishes
l 15 AMP Round Pin Socket Outlets available in Synthetic Chalk White finish only
Features
Dimensions (mm)
BOX TYPESFlush Flush for extra wiring space 866ZIC 877ZIC
86
86
22.8
7.35
5 Amp
86
86
25.5
7.35
15 Amp
wiring devices | decorative www.mkelectric.co.uk
Elements Collection Technical9
Shaver/Toothbrush Supply UnitStandards and approvals
Shaver/Toothbrush supply units comply with BS EN 61558-2-5: 1998.
Accommodates plugs as follows:
l British 5mm dia pins on 16.6mm pitch (230V socket) to BS 4573: 1970
l European 4mm dia pins on 17 to 19mm pitch (230V socket) to CEE 7/16 Euro Type C to BS EN 50075
l Australian 6.5 x 1.6 flat blades each set at 30° to the vertical on a nominal pitch of 13.7mm (230V socket) CEE 7/16 Euro Type C to BS EN 50075
l American 6.6 x 1.6 flat horizontal blades on 12.7mm pitch (115V socket) to NEMA 1-15 - Type A to UL498/NEMA WD6
Description
Designed for ease of installation and having many of the advantageous design features of the Elements Collection.
May be used in bathrooms and washrooms but must only be installed in accordance with BS 7671: 2008.
Technical specification
Electrical
Voltage rating:K34709: 230V a.c. Input (will operate at 220-250V a.c.)230V or 115V nominal outputs
Current rating:K34709: 200mA max. (internal thermister trip current)
Maximum load:20VANo load voltage < 275V
Terminal capacities:Each terminal will accommodate 1 x 4mm2 or2 x 2.5mm2 solid conductors*
Physical
Ambient operating temperature:–5°C to +40°C
IP rating:IP41 (In Zone 2 if fixed where direct spray from showers is unlikely)
Max. installation altitude:2000 metres
*The design of this unit means that on no load the transformer output is allowed to be as high as 275V. This means that rechargeable shavers and toothbrushes intended for use on the continent may be damaged by the inrush current created by this higher voltage. Rechargeable shavers and toothbrushes with a wide range of input voltage should be recharged at 115V. Shavers and toothbrushes manufactured for the UK are designed to be used with a transformer unit. Loads in excess of 20VA may cause the solid state overload to operate before shaving is completed. This is to protect the transformer.
Dimensions (mm)
Shaver/Toothbrush supply unit should be wall mounted.
Installation
� Top access terminal screws make wiring quicker and easier
� Automatic primary supply switching on insertion of plug
� Choice of 230V or 115V output socket positions
� Safety interlocked shutters to prevent insertion of two plugs simultaneously
� Only one size of screwdriver required for installation
� Front plate fixing screws retained on rear case moulding
� Integral over current device to protect transformer
� Suitable for use with electric toothbrush chargers.
BOX TYPESFlush mounting onlyMetal box 878ZIC (minimum metal mounting box depth is 47mm)
Elements Modular Switches require a separate frontplate, when ordering ensure the appropriate module and frontplate is selected.
Standards and approvals
All Elements switches comply with IEC/BS EN 60669-1:1999.
Dimensions (mm)
1 gang
Sectional drawings show the furthest projections from the back of the frontplate (wall surface).
l 16 standard finishes
l Many more customised combinations of standard colours, materials and finishes available
l Bespoke colours, materials and finishes available via the Design Service
l Switch contacts with silver contacts in both surfaces for good continuity
l Positive switch action
l Only one size of screwdriver required for installation
l Backed out and captive terminal screws
l Locator versions available for low light level applications
Features
Technical specification
Electrical
Voltage rating:250V a.c. 50Hz
Current rating:1way/2way - 10AX or 20AX versions available.All Push switches - 10A onlyIntermediate - 20AX onlyDouble Pole - 20AX onlyCentre Off - 10A only
Terminal capacity:All products – 4 x 1mm2
4 x 1.5mm2
3 x 2.5mm2
2 x 4mm2 1 x 6mm2
Contact gap:3mm switch contact gap (Except K34900 and K34901)
Physical
Operating temperature:–5°C to +40°C
IP rating:IP4X
Max. installation altitude:2000 metres
Operational testing (all plateswitches):tested to 100,000 operations for mechanical lifetested to 10,000 operations at 20 amp rating.
BOX TYPESFlush
1 and 2 gang switches 861ZIC(25mm deep)
3 and 4 gang switches 862ZIC(25mm deep)
1 gang wide rocker
2 gang
86
86
86
86
13.7
7.35
86
86
13.7
7.35
wiring devices | decorative www.mkelectric.co.uk
Elements Collection Technical13
Grid Switch Modules
Wiring Diagrams
One-way switching
NL
One-way switching
1
Common
Lamp/s
NL
Two-way switching
Lamp/s
21
Common
12
Common
Two-way switches
Dotted lines show alternative switch positions
NL
Two-way switching3 wire control
21
Common
21
Common
Two-way switches
Dotted lines show alternative switch positions
Lamp/s
SW.L
L
NL
Two-way plusintermediate switching
12
Common
21
Common
Two-wayswitch
Two-wayswitch
Dotted lines show alternative switch positionsLamp/s
1
1
2
2
1
1
2
2
Intermediateswitch
Two-way plusintermediate switching3 wire control
21
Common
21
Common
Two-wayswitch
Two-wayswitch
Dotted lines show alternative switch positions
Intermediateswitch
NLamp/s
SW.L
Two-way switching – 2 wire control
NL
One-way switching
1
Common
Lamp/s
NL
Two-way switching
Lamp/s
21
Common
12
Common
Two-way switches
Dotted lines show alternative switch positions
NL
Two-way switching3 wire control
21
Common
21
Common
Two-way switches
Dotted lines show alternative switch positions
Lamp/s
SW.L
L
NL
Two-way plusintermediate switching
12
Common
21
Common
Two-wayswitch
Two-wayswitch
Dotted lines show alternative switch positionsLamp/s
1
1
2
2
1
1
2
2
Intermediateswitch
Two-way plusintermediate switching3 wire control
21
Common
21
Common
Two-wayswitch
Two-wayswitch
Dotted lines show alternative switch positions
Intermediateswitch
NLamp/s
SW.L
Two-way switching – 3 wire control
NL
One-way switching
1
Common
Lamp/s
NL
Two-way switching
Lamp/s
21
Common
12
Common
Two-way switches
Dotted lines show alternative switch positions
NL
Two-way switching3 wire control
21
Common
21
Common
Two-way switches
Dotted lines show alternative switch positions
Lamp/s
SW.L
L
NL
Two-way plusintermediate switching
12
Common
21
Common
Two-wayswitch
Two-wayswitch
Dotted lines show alternative switch positionsLamp/s
1
1
2
2
1
1
2
2
Intermediateswitch
Two-way plusintermediate switching3 wire control
21
Common
21
Common
Two-wayswitch
Two-wayswitch
Dotted lines show alternative switch positions
Intermediateswitch
NLamp/s
SW.L
Two-way switching plus intermediate switching – 2 wire control
NL
One-way switching
1
Common
Lamp/s
NL
Two-way switching
Lamp/s
21
Common
12
Common
Two-way switches
Dotted lines show alternative switch positions
NL
Two-way switching3 wire control
21
Common
21
Common
Two-way switches
Dotted lines show alternative switch positions
Lamp/s
SW.L
L
NL
Two-way plusintermediate switching
12
Common
21
Common
Two-wayswitch
Two-wayswitch
Dotted lines show alternative switch positionsLamp/s
1
1
2
2
1
1
2
2
Intermediateswitch
Two-way plusintermediate switching3 wire control
21
Common
21
Common
Two-wayswitch
Two-wayswitch
Dotted lines show alternative switch positions
Intermediateswitch
NLamp/s
SW.L
Two-way switching plus intermediate switching – 3 wire control
NL
One-way switching
1
Common
Lamp/s
NL
Two-way switching
Lamp/s
21
Common
12
Common
Two-way switches
Dotted lines show alternative switch positions
NL
Two-way switching3 wire control
21
Common
21
Common
Two-way switches
Dotted lines show alternative switch positions
Lamp/s
SW.L
L
NL
Two-way plusintermediate switching
12
Common
21
Common
Two-wayswitch
Two-wayswitch
Dotted lines show alternative switch positionsLamp/s
1
1
2
2
1
1
2
2
Intermediateswitch
Two-way plusintermediate switching3 wire control
21
Common
21
Common
Two-wayswitch
Two-wayswitch
Dotted lines show alternative switch positions
Intermediateswitch
NLamp/s
SW.L
N.B. Terminal positions may alter. The above diagrams are to show wiring layout.
Description
Switches featuring locators and indicators use LED illumination.
All switches fitted with a locator are intended to give a very low light output whilst the switch is turned off. The low level of power flowing in this circuit is compatible with the majority of installation requirements however, certain lamp types or installations using multiple intermediate switches on one circuit may require the use of a snubber capacitor. The recommended capacitor to use would be X2 rated 275V 0.1 µ F.
Switches incorporating indicator or locator illumination must be disconnected before carrying out any site installation testing.
These switches comply with BS EN 60669-1 SS247, IEC / MS IEC 60669
15
Description
A range of switches harmonising with the Elements style, suitable for the switching of all domestic, commercial and industrial appliances where higher current ratings are required, i.e. cookers, heaters, commercial refrigeration units etc.
l Positive switch action
l Positive double pole switching
l Toggle action switches
l Replaceable neon indicators
Features
Note: These switches are not recommended for switching large banks of PCs.
The Elements Do Not Disturb / Make Up Room Switches have been developed along with a number of other products for hotels and hospitality venues, offering guests comfort and control. The Do Not Disturb / Make Up Room Switches allow guests to offer indications to service staff from the bedside.
Elements Modular Switches require a separate frontplate, when ordering ensure the appropriate module and frontplate is selected.
Standards and approvals
All Elements switches comply with IEC / BS EN 60669-1:1999.
Dimensions (mm)
Room Switch
l 16 standard finishes
l Many more customised combinations of standard colours, materials and finishes available
l Bespoke colours, materials and finishes available via the Design Service
l All products clearly marked with BS numbers and ratings
l Switch contacts with silver contacts in both surfaces for good continuity
l Positive switch action
l Only one size of screwdriver required for installation
l Backed out and captive terminal screws
Features
Technical specification
Electrical
Voltage rating:250V a.c. 50Hz
Current rating:10 amps
Terminal capacity:All products – 4 x 1mm2
4 x 1.5mm2
3 x 2.5mm2
2 x 4mm2 1 x 6mm2
Contact gap:K33900DND - Mini gapK33885DND - Normal gap
Physical
Operating temperature:–5°C to +40°C
IP rating:IP4X
Max. installation altitude:2000 metres
BOX TYPESFlush
All switches 861ZIC(25mm deep)
Room Switch - Inside “Occupancy Selector”
Corridor Switch - Outside “Bell Push/Indicator”
Connection of LED Indicators
Corridor Switch
86
86
7.35
12.9
86
86
7.35
12.9
wiring devices | decorative www.mkelectric.co.uk
Elements Collection Technical17
Keycard Switch with Time DelayStandards and Approvals
IEC 60669-2-1, BSEN 60669-2-1, MSIEC 60669-2-1, SS 227:Pt.2
Description
The Elements Keycard Switch with Time Delay has been developed along with a number of other products for hotels and hospitality venues, offering guests comfort and control, whilst delivering energy efficiency by avoiding energy waste in unoccupied rooms.
The Keycard Switch has a time delay once the card is removed ensuring guests are not left in the dark.
l 16 standard finishes
l Many more customised combinations of standard colours, materials and finishes available
l Bespoke colours, materials and finishes available via the Design Service
l All products clearly marked with BS numbers and ratings
Suitable for use in all LJU6C, Euro and MK Modular frontplates, available in the Logic Plus range, Cat 5e and Cat 6 modules suitable for use in structured cabling distribution systems.
Installation
l Maximum cable length 90m.
l Cable bend radii, 40mm during installation, 20mm after installation.
l Maximum pull force 8.7kg.
l Do not over tighten cable ties.
l Do not unwind the twists in the wire pairs by more than 13mm max.
MK ELECTRIC (MALAYSIA) SDN. BHDC/O SYMPHONY CORPORATEHOUSE SDN.BHD22ND FLOOR, MENARA EON BANK288, JALAN RAJA LAUT 50350 KUALA LUMPUR
R
HONEYWELL CONFIDENTIAL AND PROPRIETARY
MODIFICATION TEXT:
ECO No.
ECO DATE
REVDRAWING No.
MATERIAL
FINISH
TITLE
SUB TITLE
ENVIRONMENTAL & COMBUSTION CONTROLS
FIRST ANGLE PROJECTION
PAPER SIZE A3 SCALE 1:1 SHEET 1 OF 1
DIMENSIONS AND TOLERANCES PER BRITISH STANDARDS AND
ECC ENGINEERING STANDARDS
GENERAL TOLERANCES:
LINEAR ±0.15HOLE DIA ±0.08
RADII ±0.05ANGULAR ±0.50
PROTECTED BYDIN ISO 16016
PACKAGING SPEC No: PERMIT No: IMPRESSIONS: MM
PROJ NO. DRAWN BY DATE: DRAWN BY:
線位圖-2
A
50057134
50057134,50057135
50057135
12
63
17
45
RJ45 Cat.5e Euro - Angled K5844
UNITS
1
2
3
4
5
1
2
3
4
A B C D E F G H
A B C
MK ELECTRIC (MALAYSIA) SDN. BHDC/O SYMPHONY CORPORATEHOUSE SDN.BHD22ND FLOOR, MENARA EON BANK288, JALAN RAJA LAUT 50350 KUALA LUMPUR
R
HONEYWELL CONFIDENTIAL AND PROPRIETARY
MODIFICATION TEXT:
ECO No.
ECO DATE
REVDRAWING No.
MATERIAL
FINISH
TITLE
SUB TITLE
ENVIRONMENTAL & COMBUSTION CONTROLS
FIRST ANGLE PROJECTION
PAPER SIZE A3 SCALE 1:1 SHEET 1 OF 1
DIMENSIONS AND TOLERANCES PER BRITISH STANDARDS AND
ECC ENGINEERING STANDARDS
GENERAL TOLERANCES:
LINEAR ±0.15HOLE DIA ±0.08
RADII ±0.05ANGULAR ±0.50
PROTECTED BYDIN ISO 16016
PACKAGING SPEC No: PERMIT No: IMPRESSIONS: MM
PROJ NO. DRAWN BY DATE: DRAWN BY:
線位圖-2
A
50057134
50057134,50057135
50057135
12
63
17
45
RJ45 Cat.6 Euro - Angled K5746 - LJU6C K5846 - Euro, K5864 - Euro Angled
UNITS
1
2
3
4
5
1
2
3
4
A B C D E F G H
A B C
MK ELECTRIC (MALAYSIA) SDN. BHDC/O SYMPHONY CORPORATEHOUSE SDN.BHD22ND FLOOR, MENARA EON BANK288, JALAN RAJA LAUT 50350 KUALA LUMPUR
R
HONEYWELL CONFIDENTIAL AND PROPRIETARY
MODIFICATION TEXT:
ECO No.
ECO DATE
REVDRAWING No.
MATERIAL
FINISH
TITLE
SUB TITLE
ENVIRONMENTAL & COMBUSTION CONTROLS
FIRST ANGLE PROJECTION
PAPER SIZE A3 SCALE 1:1 SHEET 1 OF 1
DIMENSIONS AND TOLERANCES PER BRITISH STANDARDS AND
ECC ENGINEERING STANDARDS
GENERAL TOLERANCES:
LINEAR ±0.15HOLE DIA ±0.08
RADII ±0.05ANGULAR ±0.50
PROTECTED BYDIN ISO 16016
PACKAGING SPEC No: PERMIT No: IMPRESSIONS: MM
PROJ NO. DRAWN BY DATE: DRAWN BY:
線位圖-3
A
50057136
50057134,50057135
50057137
8
7
4
53
1
6
2
1 7
8
4
3 5
2
6
RJ45 Cat.6 ScreenedK5746S - LJU6C, K5846S - Euro
UNITS
1
2
3
4
5
1
2
3
4
A B C D E F G H
A B C
MK ELECTRIC (MALAYSIA) SDN. BHDC/O SYMPHONY CORPORATEHOUSE SDN.BHD22ND FLOOR, MENARA EON BANK288, JALAN RAJA LAUT 50350 KUALA LUMPUR
R
HONEYWELL CONFIDENTIAL AND PROPRIETARY
MODIFICATION TEXT:
ECO No.
ECO DATE
REVDRAWING No.
MATERIAL
FINISH
TITLE
SUB TITLE
ENVIRONMENTAL & COMBUSTION CONTROLS
FIRST ANGLE PROJECTION
PAPER SIZE A3 SCALE 1:1 SHEET 1 OF 1
DIMENSIONS AND TOLERANCES PER BRITISH STANDARDS AND
ECC ENGINEERING STANDARDS
GENERAL TOLERANCES:
LINEAR ±0.15HOLE DIA ±0.08
RADII ±0.05ANGULAR ±0.50
PROTECTED BYDIN ISO 16016
PACKAGING SPEC No: PERMIT No: IMPRESSIONS: MM
PROJ NO. DRAWN BY DATE: DRAWN BY:
線位圖-3
A
50057136
50057134,50057135
50057137
8
7
4
53
1
6
2
1 7
8
4
3 5
2
6
RJ45 Cat.5e Screened K5845S - Euro
wiring devices | decorative www.mkelectric.co.uk
Elements Collection Technical21
Telephone, RJ11/12, BNC Data and Blank Modules
Installation (Telephone socket modules)
Product performance, systems compatibilityMaster Sockets: For use as the first socket outlet on a direct exchange. They contain the required surge protector (for line protection against electrical surges) and ringing capacitor.
Secondary Sockets: for use as extension sockets when connected on the same line as a Master Socket.
Wiring regulation restrictionsDomestic Installations: The total REN (Ring Equivalent Number) value of all telephone equipment connected on a line must not exceed 4.
Standards and approvals
Telephone sockets K5820 and K5821 comply with the following:
BS 6312: 2.2
Data sockets K5801, BS 5733: 2010 (where applicable).
IP rating: IP2XD – K5820, K5821, K5801 and K5787. IP4X – K180, K188, K186 and K170
Max. installation altitude: 2000 metres
Description
A range of telephone, data and blank modules to fit Euro and LJ6UC front plates. BNC Euro modules with a 50Ohm crimp connector suitable for use with RG58, URM43, URM76 and Beldon 9907 type co-axial cables are also available.
l Meet all relevant BS, OFTEL and cabling standards
l Interchangeable modules clip into frontplates
l Front fixing facilitates easy exchange of modules
l Part of a complete range of products for telephone and data processing requirements
Telephone sockets
l 100% tested before delivery
l Quick, simple and reliable IDC connectors
l Can be specified for all applications
Data sockets
l Latest specification for high performance systems
All MK Digital TV Outlets comply with BS 5733 and BS EN 50083 where applicable.
Also IEC 169-2, BS EN 60169-24 and BS 6312 Part 2.
Modular products are Euro compatible.
Description
There are two ranges of diplexer and triplexer products, an established range suitable for VHF TV, and a range suitable for digital radio (DAB).
Diplexer modules are for connecting to a single co-axial aerial down lead carrying combined TV and FM signals. The filtering in the diplexer splits out the appropriate signal and feeds it to the relevant output connection. A DC control path is provided in the TV signal path through the diplexer.
Triplexer modules are for connecting to a single co-axial aerial down lead carrying combined TV, FM and SAT signals. The filtering in the triplexer splits out the appropriate signal and feeds it to the relevant output connection. A DC control path is provided in the SAT signal path through the triplexer.
The quad outlet contains a triplexer together with a separate satellite output, for use with Sky+, or more complex installations.
Telephone secondary outlets are provided on some products for connection of telephone or for interactive TV applications.
l Non Isolated
l Fully screened
l Earth terminal provided on TV modules
Features
Digital TV, Radio and Telephone Outlets
Cable management
Digital TV outlets can be mounted in a variety of MK trunking systems.
Installation
l When installing the TV Co-axial cable ensure that all cable bends are smooth so that the inner insulation is not crushed or squashed. Otherwise the TV signal quality may be affected.
l Not suitable for loop-in loop-out installations.
l Use CT100 cable (or equivalent.)
Dimensions (mm)
6.5
Screening braid to remain inplace over the inner insulation
6.5TV Co-axial cable stripping details
Earth terminal
Co-axialcable
Foil EMCscreeninggasket
Clampingplate fixingscrews
Cableclampingplate
Earthterminal
Clampingfixing screws
View with cableclamp removed
Cable clamp
Co-axialcable
Note: Minimum box depth: 47mm
Euro 2 module Triplexer Euro 2 module QuadplexerEuro 1 module
Technical specification
Single Outlets
TV/FM IEC Male or Female DC-950MHzSATF-Type DC-1.75GHz
Product performance, systems compatibilityIsolated Outlets are intended for use where safety isolation (rated at 2000V ac) is required to provide protection against faults occurring within any mains powered product used on different parts of the distribution system. They are not suitable for use in systems where DC signals are passed through the socket, (e.g. where masthead/headend equipment is controlled by receiver/decoder equipment).
Diplexer Outlets are used in distribution systems where both TV and FM band signals are combined on a single aerial downlead. The filtering in the diplexer separates the appropriate signals and feeds them through to the relevant output connection port.
Cable Routing and Use of Cable ClampSharp bends in the cable must be avoided during installation. The single TV/FM socket is fitted with a cable clamp that can be fixed on either side of the termination position to facilitate this.
When tightening the screening braid clamps ensure that the cable is firmly gripped and that the inner insulation is not squashed flat beyond a slight oval shape.
Safety InformationTV outlets or modules must not be installed in the same enclosure as equipment rated in excess of 50V, (e.g. mains rated 13A sockets or switches).
TV/FM and Satellite Socket Outlets
Method of installation of TV and FM aerial connection by using MK co-axial socket outlet and only one downlead.
Conventional distribution system for TV and FM signals using a single aerial downlead.
The signals from the TV and FM aerials and the satellite dish are combined together using two products. The first combines the TV and FM signals and the second adds the Sky signal to the TV/FM signal and provides a DC control path to power the LNB unit on the satellite dish. (These products are not supplied by MK).
The single aerial down lead feeds into the triplexer (black lines in wiring diagram).
The separated satellite signal is then fed to the decoder. The decoded satellite signal is then fed into the VCR along with the TV signal from the Triplexer. The output signal from the VCR then feeds into the TV and also back to the single outlet and onto the distribution amplifier (black lines in wiring diagram).
The single cable back-feed then feeds back to the input of a multi way distribution amplifier, (typically located in the loft or garage) (red lines in wiring diagram).
Each individual output from the distribution amplifier is then fed to the individual rooms in the house to a standard TV (single or diplexer) outlet to which the TV/VCR and/or Hi-Fi can be connected (blue lines in wiring diagram).
1
2
3
4
FM TV
SAT 1
DAB
TV
TVTV
TV
VID
SKY/DIG
VID
TV DIST
HI-FI
SAT 2
1
4
4
4
2
3
wiring devices | decorative www.mkelectric.co.uk
Elements Collection Technical25
Modular Range: PIR DetectorDescription
The Elements PIR Detector will deliver energy savings and lighting usage management in a wide range of applications. Offering effective and efficient detection for control of lighting, this stand alone solution is easy to install and program, with the additional benefit of variable time delay from 30 minutes to permanently on.
Electronics Ballast:3 x 58W (max. inrush current 80A/20ms)
Contact Gap:Micro gap
Terminal Capacity (Screwless Terminal):Stranded Cbales1 x 2.5mm2
Solid Cables1 x 2.5mm2
1 x 4mm2
Earth Terminal (screw terminal):4 x 2.5mm2
3 x 4.0mm2
2 x 6.0mm2
Physical
Ambient operating temperature:0�C to +35�C
Max installation altitude:2000 metres
l 16 standard finishes
l Many more customized combinations of standard colours, materials and finishes available
l Bespoke colour materials and finishes available via the Design Service
l Detection range of 8m
l Delivers energy saving by switching lights off when occupancy is not detected
l Offers safety and comfort by switching lights on when occupancy is detected
l Easy to install and program
l Time delay from 30 minutes to permanently on
Features
Frontplate and Module Installation
WALL BOX
PATRESS
MODULE WITH METAL PLATE
FRONTPLATE MOTION SENSOR MODULE
Installation
For optimal detection and control sufficient distance (1m minimum) should be maintained between the PIR Detector and lighting fixtures in order to prevent undesirable motion detector switching. The optimal installation height is 0.8m – 1.2m. Installation in areas where excessive air movement occurs can cause false activations.
The Elements Echo Transmitters are part of an innovative range of entirely wireless, batteryless and self powered switches only available from MK Electric. The Elements Echo Transmitters communicate with Echo receivers to switch mains power. Elements Echo Transmitters send an RF signal at 868.3 MHz, the unique feature of these transmitters is the signal transmission is made with no need for mains power or batteries.
Mounting Transmitters
l All transmitters can be mounted to any 1 gang back box
l All transmitters can be mounted directly to the wall surface
Technical specification
Physical
Operating temperature:-5°C + 40°C
Operating frequency:868.3 MHz
IP Rating:IP2X
Max installation altitude:2000m
l 16 standard finishes
l Many more customized combinations of standard colours, materials and finishes available
l Bespoke colour materials and finishes available via the Design Service
l Wireless and batteryless, using RF technology with ranges up to 30min ideal conditions
l The transmitters are quick and easy to install with no need for cabling from the switch to the lighting circuit
l See the Echo range for available receivers
Features
Frontplate and Module Installation
PATRESS
MODULE PLATE
LATCHESTRANSMITTER MODULE
Standards and approvals
BS EN 60669-1, BS EN 60669-2-1,ESTI EN 301 489-1 & -3,ESTI EN61000-6-2, ESTI EN300 220-3, EN60950-1
FRONTPLATE
Dimensions (mm)
86
86
9.65
3.00
wiring devices | decorative www.mkelectric.co.uk
Elements Collection Technical27
Modular Range: Roller Shutter / Blind Control Controller
Description
The Elements Modular Roller Shutter / Blind Controller will operate a motor run device enabling the control of window coverings.
Technical specification
Electrical
Voltage Rating:250 VAC
Current Rating:10A
Terminal Capacity:Stranded Cables2 x 2.5mm2
1 x 4.0mm2
Solid Cables:2 x 2.5mm2
2 x 4.0mm2
Earth Terminal:4 x 2.5mm2
3 x 4.0mm2
2 x 6.0mm2
Physical
Ambient Operating Temperature:0�C to +35�C
IP Rating:IP2X
Max installation altitude:2000 metres
l 16 standard finishes
l Many more customized combinations of standard colours, materials and finishes available
l Bespoke colour materials and finishes available via the Design Service
l Easy to install
Features
Dimensions (mm)
Frontplate and Module Installation
Standards and approvals
IEC60669-1:1998 + A1999 + A2:2006
Installation
For optimal performance ensure the product is orientated correctly.
The wrong orientation may cause the product to function incorrectly.