This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Slide shoe for cams, 2 parts, consisting of housing and latch.
Matching cams as of 35 mm, steel • product system 1.102 and stainless steel product system 7-080, in combination with a 3-point-cam adapter it matches 3-point-cam applications as well.No abrasion of the metal of the • clamping surface resp. cam and therefore safety concerning electronic built-in components (risk of short circuits in computer, server etc.).Good gliding properties, therefore low • friction coeffi cient, no fretting of the material.Prevents the surface from being • scratched.
Tool-less assembly and disassembly. • The housing will be hold at the slope of the cam and being fi xed to the latch.The assembly will be carried out with • the already installed quarter turn, it is possible to retrofi t at any time (please take the H-height into consideration).Separable after durability (recyclable).• Caution:• The H-height diminishes by 2 mm. E.g. cam 200-0418 (H-height 18 mm) results into an H-dimension of 16 mm.
Captive D-SNAP-Joiner for joining flat metal sheets.• The joining of metal sheets is
achieved by pushing the Captive D-SNAP-Joiner into the cutouts.
• The front panel can be separated from the rear panel by using a Phillips H2 screwdriver. Turn the Phillips head insert to pull the front panel away.
• Designed for ease of use by the enduser - disengaging is achieved by turning the knob ¼.
• Save up to 90% assembly time.• The dimension always means the
thickness of both sheets together.• Completely pre-assembled, one-piece.
• Machinery Directive 2006/42EC: In order to meet the Machinery Directive 2006/42EC an additional U-shaped spring is riveted onto the housing. The Captive D-SNAP-Joiner is held in position and remains held by the U-shaped spring.
• The Captive Joiner eliminates the concern of losing, dropping or misplacing hardware.
Elegantly designed, sealed polyamide quarter-turn with moulded-in TPE seal that is permanently fixed in the PA housing, thus ensuring that it cannot be lost.• The seal is located under the head
and inside the housing.• Colored seal.• Water- and dust-tight according to
IP65/67 DIN EN 60529.• The Quarter-Turn consists of three
basic components which can be combined to suit your application.
• Insert and cam can be clipped together without tools before the installation in the housing.
• A pre-assembled Quarter-Turn can be installed through the cutout.
• RH and LH application.• Maximum load for the cam 250N.• Load may be increased to 600N with
use of a fi xing plug.• Attention: Please consider the
packing units!
Material:• Housing, insert, cam and nut: PA6,
black• Seal: TPE, red• Fixing plug: PA6, red
Part No. packing unit / piece see product systema) Housing 2K 200-0211.00-00000 1000a1) Nut 203-0901.07-00000 1000
Inserts:b) Double bit 3mm pin 100-0388.50-00005 250b1) Double bit 5mm pin 100-0388.50-00001 250b2) Square 8mm 100-0388.50-00002 250b3) Triangular 8mm 100-0388.50-00003 250b4) Slotted 2x4mm deep 100-0388.50-00004 250
4-400 Scharnier PA Pr01 180° 60x40für innenliegende Tür, anschraubbar
Bestell-Nr.Scharnier PA 218-9220
Werkstoff:• Scharnier: PA6, schwarz
Formschönes Anschraubscharnier für Senkschrauben, DIN 7991 oder nach DIN ISO 10642 und nach DIN 965 oder DIN ISO 7046.• Links und rechts einsetzbar.• Öffnungswinkel 180°.• Unverlierbarer Stift.• Stift gegen herausschlagen gesichert.• Spielfreie Ausführung.• 6 teiliges Gewerbe.• Geringes Gewicht.• Korrosionsbeständig.• Abgerundete Kanten.