1 HYDRAULICS BACKED BY OUR ROYAL SERVICE PROMISE DESIGNED TO MEET the REQUIREMENTS of a WIDE VARIETY of APPLICATIONS. INDUSTRIAL AGRICULTURAL HIGH QUALITY COMPONENTS HIGH TOLERANCE MACHINING OUTSTANDING HIGH PRESSURE PERFORMANCE SHUR-LIFT HYDRAULIC CYLINDERS Unique fluid solutions powered by service.
49
Embed
01 Hydraulics 6/6/06 8:27 AM Page 1 SHUR-LIFT HYDRAULIC ... · shur-lift 2,500 snap ring utility cylinders shur-lift 3,000 threaded ... 01 hydraulics 6/6/06 8:27 am page 4. 5 shur-lift
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1
HYDRAULICS
BACKED BY OUR ROYAL SERVICE PROMISE
DESIGNED TO MEET the REQUIREMENTS of a WIDE VARIETY of APPLICATIONS.
WARNING: FAILURE, IMPROPER SELECTION OR IMPROPER USE OF ANY HYDRAULICPRODUCTS AND/OR SYSTEMS OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURYAND/OR PROPERTY DAMAGE.
01 Hydraulics 6/6/06 8:27 AM Page 4
5
SHUR-LIFT 3,000 THREADED HEADFEED TUBE CYLINDER
• Cylinder features a feed tube running from the shaft end to a base end mounted port
HOIST CYLINDER ONLY• Threaded head design• 14" stroke, 2" shaft• 21-1/2" retracted length• #8 ORB ports• 1-1/4" dia. shaft end with 1/2" pinhole• Base pineye width: 7-1/4", pinhole dia.: 1-1/4"• 3,000 PSI max. continuous pressure• For single lever assembly5" BORE – 12 ton capacity1200079 – Wt. 58.4 lbs. . . . . . . . . . . . . . . . . . . . . . . . 35999
HYDRAULIC TRUCK AND TRAILER HOIST WITHCYLINDER• Build your own truck or trailer hoist for a low cost• Upper lift arms are equipped with telescoping brackets• Lever style design to give max. lifting capacity• The hoist comes complete with a 4" bore cylinder
making the hoist capable of lifting 7 tons (wheninstalled according to manufacturer's specifications)
• If heavier lifting is required a 5" bore hydrauliccylinder (item 1200079) can be used to make a 12 ton hoist
Can a double acting cylinder be used in a single actingapplication?
By installing a breather plug in one port to prevent air borncontaminates from entering the cylinder our double actingcylinders can be converted to single acting.
• Threaded head design• 24" stroke, 2" shaft• #8 ORB ports• 3,000 PSI max. continuous pressure• Can be used as replacement on Princess Auto
logsplitters or to build your own
• Clevis mount with 1" pinhole in base end• Shaft end has been cut down to 1-1/2"
with a 3/8" drilled pinhole
• Front mount with four 1/2"-13 UNC nuts• Shaft end has 1-1/2" 12 UNF threading
®
Check out our shop presses onpages 198-200
HYDRAULIC POWER PACKCYLINDER
Designed to be used with shop presses as well asa variety of lifting, spreading, bending,straightening, pushing, pulling or clampingoperations.• 50 ton capacity• 6" bore, 5-1/2" stroke• 2" shaft• 11-3/4" retracted height• 3/8" NPT ports• Base plate measures: 7" x 9-1/2"• Ram speed @ 1.6 GPM: 25.4 seconds
National Call Centre: 1-800-665-8685Factory Direct: 1-204-654-5232 ext. 368Fax: 1-204-668-4530or visit your nearest store.
Designed and Built to your Specifications
Delivery in 10 working days*
Custom Build Cylinder Program
* From receipt and confirmation of order (max. 5 pieces). Not including transit time.
• 3,000 PSI max. continuous pressure• Bore sizes from 1-1/2" to 6" • Strokes from 2" to 48"• Threaded head design• O-ring boss ports for superior high pressure • A wide variety of port configurations, shaft
WARNING: FAILURE, IMPROPER SELECTION OR IMPROPER USE OF ANY HYDRAULIC PRODUCTSAND/OR SYSTEMS OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND/OR PROPERTYDAMAGE.
Princess Auto provides product and/or system options for further investigation by usershaving technical expertise. It is important that you analyze all aspects of your application andreview the information concerning the product or system. Due to the variety of operatingconditions and applications for these products or systems, the user, through its own analysisand testing, is solely responsible for making the final selection of the products and systemsand assuring that all performance, safety and warning requirements of the application are met.The products described herein, including without limitation, product features, specifications,designs, availability and pricing, are subject to change without notice.
Replaces worn end cap or can be welded to customer's own dies.Fits 30 ton press #3460052 on p.1991250029 – Wt. 0.9 lbs. . . . . . . . . . . . . . . . . . . . 2499
CYLINDERS ENDSA) CROSS TUBEDrilled for 3/16" drive-in grease nipple.
Dimensions Wt. ITEM PRICE1" I.D. x 2-1/4" L 0.6 8001456 5.991" I.D. x 2-3/4" L 0.7 8001457 6.491" I.D. x 3-1/4" L 0.9 8001458 6.991" I.D. x 3-3/4" L 1.0 8001460 7.491" I.D. x 4-1/4" L 1.2 8001461 7.991-1/4" I.D. x 2-3/4" L* 1.5 8001469 9.991-1/4" I.D. x 4-3/4" L* 2.5 8001471 11.991-1/4" I.D. x 5-3/4" L* 3.1 8001472 12.99* Heavy wall
Dimensions Wt. ITEM PRICE1" I.D. x 3/8" thick 0.4 8001473 8.491" I.D. x 1/2" thick 0.7 8001474 8.991" I.D. x 3/4" thick 1.0 8001475 9.991-1/4" I.D. x 1" thick 1.4 8001476 10.99
ABB) MALE TANG
Use two to make a base end clevis.
01 Hydraulics 6/6/06 8:28 AM Page 7
8
POW
ER P
ACKS HIGH PRESSURE HYDRAULIC
PISTON PUMP
The WILLIAMS Piston Pump is a compact, bi-rotational, and completely self-containedhydraulic power unit. Its extreme reliability anddurability make it suited to a wide range ofapplications including hoists, presses, dump bodies,and trucks.Features: • Built-in pressure relief• Constant flow at low RPMs• High contamination tolerance• All interior parts submerged in oil for longer life• Steel intake and exhaust valves• Bi-rotational• Double acting control valves• 1" shaft (with 1/2" woodruff key)• 3/8" NPT ports
Model No. Displ.Cu. In./Rev.
Min/MaxRPMs
GPM @Max. RPM
Relief ValvePressure Setting
Reservoir(GAL.)
Wt. (lbs.) ITEM PRICE
F98-4-21* 2.6 300-1,300 13.2 3,000 5.25 77.5 1220045 899.99* Maximum pressure on this unit can be increased to 5,000 PSI when relief valve #7120007 is installed. Available byspecial order. Call 1-800-665-8685 for more information. Replacement pump available on request.
REPLACEMENT BREATHER CAPS
For Williams pumps.1252923 – Wt. 0.1 lbs. . . . . . . . . . . . 699
VALVE ADAPTER PLATE• Enables a remote directional control
valve to be used with the piston pumps• Remove standard valve, bolt on adapter
These power packs feature a high torqueelectric motor directly coupled to a singlestage hydraulic pump. They can be usedfor a wide variety of applications includingpresses, scissor lifts, car hoists, etc.
A 56C, 56HC 2-Bolt SAE Type A 2.4 8009335 34.99B 184TC 2-Bolt SAE Type A 4.9 8009353 49.99C 56C, 56HC 4-Bolt 2.6 8009326 34.99D 184TC 4-Bolt 5.2 8009344 49.99
GAS ENGINE BRACKETS
HP Pump Mount Type Wt. (lbs.) ITEM PRICE
E 5 2-Bolt SAE Type A 1.9 8009308 39.99F 8-20 2-Bolt SAE Type A 3.8 8001759 59.99G 5 4-Bolt 1.3 2400463 39.99H 8-20 4-Bolt + SAE Type “AA” 3.8 2400003 59.99H 8-20 4-Bolt 3.8 8110751 49.99
FOOT MOUNT BRACKETSPump Mount Type Wt. (lbs.) ITEM PRICE
I 4-Bolt 0.8 8039712 44.99J 2-Bolt SAE Type A 1.7 8009317 22.99
PUMP MOUNTING PLATEPump Mount Type Wt. (lbs.) ITEM PRICE
K 2-Bolt SAE Type B 7.7 8076028 34.99
HYDRAULIC POWER PACK MOUNTING PLATE• Create your own power pack• Premade mounting holes for easy component mounting • Mount any of our gas or electric power packs and hydraulic
WE CAN HELP YOU BUILD A POWER PACK TO YOUR SPECIFICATIONS.• Over 150 different possible power pack combinations• Our PAL Hydraulics team members can help you make the right selection of motor/gas engine,
pump mounting bracket, shaft couplers and pump to meet your flow and requirements
GAS ENGINES ELECTRIC MOTORS SHAFT COUPLERS MOUNTINGBRACKETS
HYDRAULICPUMPS
SEE PAGE 92-93 SEE PAGE 83 SEE PAGE 97 SEE BELOW SEE PAGE 13-14
01 Hydraulics 6/6/06 8:28 AM Page 10
11
POWER PACKS
12 VDC HYDRAULIC POWER PACKS
These self-contained power packs can be used fora wide range of applications including cranes,dump boxes, tailgate lifts and farm machinery.They are extremely reliable and perform well in awide variety of applications. Each power packconsists of a 12 VDC motor, hydraulic pump,reservoir, valving system and remote powerswitch.
FEATURES:• This self contained power pack can be used for
a wide range of applications including cranes,dump boxes, tail gate lifts and farm machinery.
• Double acting manually controlled• Motor starts and stops by activating the manual
valve control
PRESSURE UP TO5,000 PSI
SPX STONEPOWER PACK CONVERSION COMPONENTS
These components are available in all of our retail stores and through our mail order department.Contact your local Princess Auto for more information!
ENDHEAD
12 VDC MOTOR
PLASTICRESERVOIRS
STEELRESERVOIRS
HIGH FLOW SUCTIONSTRAINER
PLUMBING KITS
PUMP
115/230 VACMOTORS
These components can be used with our existing power packs to either repair or modify them tomeet the specifications of a wide variety of applications.
• Turn on the clutch to engage, turn off to disengage• Static breakaway torque of 90 ft.-lbs.• Clutch draws 3.9 amps when engaged• Solid forged rotor to maximize torque and prevent
internal parts separation• Forged machined pulley resists damage from abusive
environments• Wherever possible all clutch parts are e-coated to
protect against corrosion
Voltage must not drop below 12 VDC or clutch will slipand become damaged.
A compact, efficient way to provide a source of hydraulic power for most trucks and off-road vehicles. Typical applications are snow removalequipment, grain augers and conveyors,tow trucks, salt and de-icer spreaders, andwhenever hydraulic power is needed.Features:• High strength alloy steel gear
and shaft set• Pressure balanced wear plates maintain
high pump efficiency throughout alloperating ranges
• Doweled, high strength, 3-piece cast ironconstruction
Specifications:• Mounting type: SAE Type “A” bracket
with pad mount• Rotation: clockwise• Ports (rear and side): #20 ORB inlet, #12
P.T.O. PUMPSIdeal for use with front end loaders on tractors without integral hydraulics,landscape equipment and backhoes. Slips onto tractor P.T.O. shaft, nogearbox required.• High tensile cast iron end plates and aluminum centre gear housing• Self-adjusting wear plates on both sides of the gears offset wear and
expansion• #16 ORB inlet and #12 ORB outlet ports• 1-3/8" dia., 6-tooth internal splined drive shaft• Standard speed: 540 RPM for 6-tooth shaft, max. 600 RPM
• HIGHER TORQUE • HIGHER PRESSUREThe DANFOSS OMS Series Disc Valve Motor is truly a hightorque, low speed hydraulic motor. Ideal for rock pickers,windrowers, and many other applications.
Features:• Instantly reversible• 1-1/4" shaft, #10 ORB ports• Max. continuous flow: 20 GPM• #4 ORB case drain port**Should be used when more than 1 motor are connected in series.
13 GPM @ 3,200 PSI Meets demand of higher flowactuators
Compact Size Designed for where weight andspace restrictions are specified
Convertible to single acting,motor spool, and detentpositioning
Easily adaptable to fit a wide varietyof applications
Features:• Max. continuous pressure: 3,200 PSI• Max. continuous flow: 13.1 GPM• Inlet/outlet and work port size: #10 ORB• Relief valve: preset @ 2,030 PSI, adjustable from 1,450 to 3,625 PSI SINGLE SPOOL• Designed to control a double acting cylinder or a reversible
Can I convert my hydraulic control valve to single acting by simply plugging oneof the work ports?While this will work, it will also result in a lot of heat build up within the hydraulicsystem because oil will go over the relief valve in one of the spool positions. Thebest solution is to either replace the valve or change to a single acting spoolprovided the design of the valve will allow it.
What is the advantage of using a control valve with a motor spool?The motor spool connects both work ports back to tank when the valve is in theneutral position. This allows hydraulic motors that are turning components with a lotof inertia, such as large pulleys or sprockets to freewheel to a stop when the valve isshifted to neutral. Without the motor spool the work ports would be blocked inneutral causing the motor to stop immediately. This could generate a very highpressure spike and damage components in the hydraulic system.
What information do I need to decide which hydraulic control valve is right for my system?There are a number of important specifications you should know to aide in the selection of a control valve. 1- Open or closed center 3- Maximum flow2- Maximum pressure 4- Single acting, double acting or motor spool
While this is not a complete list of possible options it would provide enoughinformation to select the proper valve for most applications..
ControlValve FAQs
STEVEN O'BRIENDate of birth: May 14, 1974Hair: Black Eyes: Brown (Wears glasses)Missing since: Mar 20, 1993 Missing from: Charlottetown, PEI
1-800-387-7962to report on a missing child anywhere in Canada
All calls confidential - No name required.A missing child is everyone's responsibility.
MISSINGHave you seen this child?
01 Hydraulics 6/6/06 8:28 AM Page 16
17
DIRECTIONAL CONTROL VALVES
Features:• Standard 3-position, 4-way/spring return to neutral unless otherwise stated• Open centre• Max. return line pressure: 1,100 PSI• Relief valve pre-set @ 2,100 PSI, adjustable from 1,500 PSI to 3,750 PSI• Control handles can be mounted in vertical or horizontal position• Max. continuous pressure: 3,600 PSI
BM SERIES MONOBLOCK DIRECTIONAL CONTROL VALVES
STANDARD
JOYSTICK
DETENT FLOATPOSITION
A B
C
BM 70
BM 40
BM 30
BM 20
Max. continuous flow 9 GPMPeak flow 12 GPMTop inlet/outlet and work ports #8 ORBSide inlet/outlet ports #8 ORB
Wt. (lbs.) ITEM PRICEA Single spool 4.6 1249598 119.99
Wt. (lbs.) ITEM PRICEA Single spool 5.6 1249721 169.99A Double spool 8.3 1249739 249.99A Three spool 11.4 1249747 349.99A Four spool 14.3 1249754 419.99A Five spool 17.6 8050315 519.99A Six spool 20.4 8050342 599.99B Double spool (float/standard) 8.9 1249713 269.99C Double spool with joystick 8.4 8006338 349.99
BM 20 SERIES
BM 30 SERIES
BM 40 SERIESMax. continuous flow 9 GPMPeak flow 12 GPMTop inlet/outlet and work ports #8 ORBSide inlet/outlet ports #10 ORB
Wt. (lbs.) ITEM PRICEA Single spool 10.4 1249796 249.99A Double spool 16.6 1249804 369.99A Three spool 21.0 1249812 479.99A Four spool 25.7 1249820 599.99C Double spool with joystick 15.8 1249788 499.99
BM 70 SERIESMax. continuous flow 17 GPMPeak flow 24 GPMTop inlet/outlet and work ports #10 ORBSide inlet/outlet ports #12 ORB
Wt. (lbs.) ITEM PRICEA Single spool 3.7 1249531 149.99A Double spool 5.5 1249549 249.99A Three spool 7.5 1249556 349.99
Max. continuous flow 4.5 GPMPeak flow 6.6 GPMTop inlet/outlet and work ports #6 ORBSide inlet/outlet ports #8 ORB
01 Hydraulics 6/6/06 8:28 AM Page 17
HYDRAULIC VALVEREMOTE CONTROL SYSTEM
• The control connects to the front of BLB valvesallowing remote operation
• Remote valve control can be mounted up to 9-3/4 ft. away from the hydraulic valve
H) JOYSTICK REMOTE VALVE CONTROL• Shift 2 hydraulic spools with 1 control• Weatherproof control can be mounted on
Specifications:• Max. continuous pressure: 3,000 PSI• Relief preset at 2,000 PSI and adjustable from
1,500 to 3,000 PSI• Max. return line pressure: 500 PSI• Ports (NPT): 3/4" inlet/outlet, 1/2" work ports• Open centre• In the detented 4th position (float) the work ports are
connected to tank, allowing the cylinder to float or themotor to freewheel
• Can be converted to closed centre or power beyond(with optional conversion plugs)
B) KNOB• 2" dia. black knobs for use on P.T.O. cable, etc.• 3/8" 24-thread3891348 – Wt. 0.1 lbs. . . . . . . . . . . . . . . . . . . . . . . . 399
C) BOWDEN PINAttaches cable end to 3/16" thick lever with 1/4" hole.3890502 – Wt. 0.1 lbs. . . . . . . . . . . . . . . . . . . . . . . . 419
A
P.T.O CABLES & ACCESSORIES
B C
ONGOING COMMITMENT TO TRAINING
PAL Hydraulics currently offers afour tier training program that isavailable to our hydraulic teammembers. The courses offeredinclude Hydraulic Specialist 1, 2and 3 and Mobile HydraulicTechnician (MHT). The MHTcertification is an industryrecognized course offered throughthe Fluid Power Society.
These courses are alladministered by our corporatetrainer Angrej Virk who is acertified Mobile HydraulicTechnician, Hydraulic Specialist
and Pneumatic Specialist. Angrejalso recently became an accreditedTrainer for the aforementionedcourses.
What is the difference between a pressure compensated flow control andpriority flow control?
A pressure compensated flow control will deliver the same controlled flowregardless of pressure as long as the inlet flow remains constant. If the inlet flowis increased or decreased the controlled flow will also vary accordingly. A priorityflow control will deliver the same controlled flow regardless of changes to theinlet flow or pressure as long as the inlet flow exceeds controlled flow demand.
TECHTIP
01 Hydraulics 6/6/06 8:29 AM Page 25
26
FLOW
CON
TROL
S
C
D
C) SPOOL STYLEAllows the reverse flow of oil through freereverse checks (Not pressure compensated).Wt. 7.1 lbs.8107278 – Max. inlet flow: 8-19 GPM
• Controls maximum return flow to equal pump output• Prevents load induced acceleration and pump cavitation• This valve is used in many load lowering applications
to control the rate of descent ie. truck boxes, tilt bed trailers or cranes
• Max. continuous pressure: 5,000 PSI• Relief pressure set @ 3,200 PSI, adjustable from
1,450 PSI to 3,625 PSI
27
RELIEF VALVESPRIORITY TYPE ADJUSTABLE FLOW CONTROLS• Designed for applications where 2 separate
hydraulic power circuits are to be served from a single pump
• A constant regulated flow is maintained at the controlled flow port regardless ofchanges in load, pressure, or input pump flow, so long as input pump flow exceeds controlled-flow port demand
• Excess flow can be used in a secondary circuit
C
A
B
D
E
F
• Relief valves are used to control the maximum pressure inthe portion of the hydraulic system where they are installed
• Protects components from over-pressuring• Use to set maximum operating pressure by setting relief
pressure approx. 300 PSI over system pressure
C&D) RELIEF VALVES• Preset @ 2,000 PSI and is adjustable from 150 to 3,500 PSI• 2 port configurations available: Type A and Type B
A) 2-WAY PILOT OPERATED CHECK VALVESMax. continuous pressure: 4,350 PSI
D
E
F
01 Hydraulics 6/6/06 8:29 AM Page 28
29
HYDRAULIC HOSEADJUSTABLE LINE THROTTLE VALVES
These simple and versatile little valves are aninexpensive way to restrict the flow of oil tovarious components in a hydraulic system. Theyare adjustable from 0 GPM to their maximumrated capacity in one direction and capable of fullflow in the other direction.
Use to:• Control cylinder stroke speed• Prevent pump cavitation by controlling
cylinders or motors with inertia loads• Meter the flow to a hydraulic motor
2 ft. 1.3 1290840 10.993 ft. 1.7 1290857 12.994 ft. 2.2 1290865 14.996 ft. 2.8 1290881 18.998 ft. 2.6 1290907 22.9910 ft. 4.3 1290923 26.99
Twisting a hydraulic hose during installation can lead to its premature failure.Installing a hose that flex's, and has as little as a 7 degree twist, can reduceservice life by as much as 90%. Also, twisted hydraulic hoses that are underpressure have a greater chance of their fittings coming loose.
TECHTIPS
01 Hydraulics 6/6/06 8:29 AM Page 29
30
HYDR
AULI
C HO
SE HYDRAULIC HOSE CENTRE
• Rubber covered with high tensile strength steel wire reinforcing
• Temperature range -40° to 100°C (-40° to 212°F)• Wire braiding allows the hose to retain flexibility
plus withstand high pressures and rough usage• Manufactured and tested to SAE 100 R1 and
HANGING & CINCHING HOSE CONTROL STRAPS:• These straps help to manage and secure hoses to prevent damage and accelerated wear• They allow hoses to expand and contract with pressure unlike cable ties which can cut and
damage the hose• The straps are 1-1/2" wide and feature high strength hook and loop closures
HANGING STRAPS CINCHING STRAPS
HOSE PROTECTION& BUNDLING SLEEVE:
• Highly abrasion resistant design protects hose(s)from being damaged when they are in contactwith friction points
• Dense burst resistance nylon compositioncontains pinhole leaks which could injureoperators
• Provides leak containment in the event of ahose ruture
• Smooth surface makes it easy to slide over verylong lengths of hose
PAL Hydraulics offers a variety of sizes and styles of hydraulic fittings tocomplete your installation or project. Size range: 1/8" to 2".Four Types of Fittings:NPT (National Pipe Thread) – Tapered thread, sealant is required for a good seal.ORB (O-Ring Boss) – O-ring seals against a machined seat in port.JIC (37° Flare) – Flare seats against opposite flare in port.ORFS (O-Ring Face Seal) – O-ring seals by compression between machine
groove and fitting face.METRIC – Straight thread, bonded seal required if attached to a port.
ThreadSize
TEE TEE TEE 90° ELBOW 90° ELBOWITEM PRICE ITEM PRICE ITEM PRICE ITEM PRICE ITEM PRICE
MALE x FEMALE BUSHINGSThread Size ITEM PRICE1/4" x 1/8" 1294701 1.193/8" x 1/4" 1294727 1.293/8" x 1/8" 8058843 1.491/2" x 1/4" 1294735 1.691/2" x 3/8" 1294743 1.793/4" x 3/8" 1294750 2.693/4" x 1/2" 8058317 3.591" x 1/2" 8058852 4.191" x 3/4" 1294776 4.19
1-1/4" x 3/4" 8106221 5.991-1/4" x 1" 8092538 5.79
1-1/2" x 3/4" 8109753 12.991-1/2" x 1-1/4" 8092520 9.99
2" x 3/4" 8109746 25.992" x 1-1/2" 8092991 22.99
ThreadSize
NIPPLE COUPLER (F x M) REDUCERS 90° ELBOW 90° ELBOW (M x F)ITEM PRICE ITEM PRICE ITEM PRICE ITEM PRICE ITEM PRICE
3/8" x 1/2" 0.1 8088452 2.491/2" x 5/8" 0.2 8088494 2.99
Thread Size
(F x M)
Wt.(lbs.) ITEM PRICE
3/8" x 1/2" 0.1 8120032 3.491/2" x 5/8" 0.1 8120206 3.895/8" x 3/4" 0.2 8120214 5.991/2" x 3/8" 0.2 8120263 1.995/8" x 1/2" 0.2 8120289 2.493/4" x 5/8" 0.2 8120297 3.49
O-RING BOSS BASIC FITTINGS
01 Hydraulics 6/6/06 8:29 AM Page 36
37
HYDRAULIC HOSE FITTINGS
Thread Size(ORB x ORFS) ITEM PRICE Thread Size
(ORB x ORFS) ITEM PRICE
#6 x #6 8092918 1.99 #6 x #6 8089252 5.49#8 x #6 8092926 2.49 #8 x #6 8089237 6.49#8 x #8 8092934 2.39 #8 x #8 8089229 5.99#10 x #8 8092942 2.99 #10 x #8 8092967 6.79#12 x #12 8092959 4.99 #12 x #12 8092975 10.99
THREAD TYPE ADAPTERS
MALE X FEMALEThread Size
(ORB x NPT) ITEM PRICE#6 x 1/4" 8059021 2.49#6 x 3/8" 1290347 2.99#8 x 3/8" 1290348 3.49#8 x 1/2" 1290349 3.69#10 x 1/2" 1290350 4.29#10 x 3/4" 8059030 5.99#12 x 1/2" 1290353 6.99
JIC 37° x O-RING BOSS ADAPTERS
O-RING FACE SEAL x O-RING BOSS ADAPTERS
Thread Size(JIC 37° x ORB)
A) COUPLER B) 90° ELBOW C) LONG ELBOWITEM PRICE ITEM PRICE ITEM PRICE
1/4" x #4 1294792 1.29 – – – –3/8" x #6 1294800 1.49 1294859 4.69 8000727 8.993/8" x #8 8006363 1.59 8088353 4.69 – –3/8" x #10 8006366 2.69 – – – –1/2" x #6 8006362 1.69 8006378 4.79 – –1/2" x #8 1294818 1.79 1294867 5.99 8000704 11.991/2" x #10 8045340 2.69 8006370 6.49 – –1/2" x #12 8006367 3.79 – – – –5/8" x #8 8088445 4.49 – – – –5/8" x #10 1294826 2.69 1294875 8.29 8000702 15.995/8" x #12 8006368 4.29 – – – –3/4" x #12 1294834 4.29 – – – –
CYLINDER PORTCONVERTERS
A
B
C
NIPPLE 90º ELBOW
SWIVEL THREAD TYPE ADAPTERS
O-RING BOSS x JIC 37°SWIVEL ADAPTERS
NPT x JIC 37°SWIVEL ADAPTERS
JIC 37° x METRIC ADAPTERS
Thread Size(ORB x JIC) ITEM PRICE
#4 x 1/4" 1290016 6.59#6 x 3/8" 1290017 6.59#8 x 1/2" 1290019 7.49#10 x 5/8" 1290020 9.49#12 x 3/4" 1290021 11.99
MALE X FEMALEThread Size(NPT x JIC) ITEM PRICE
1/4" x 1/4" 8058335 4.691/4" x 3/8" 8058344 5.693/8" x 3/8" 8058380 5.693/8" x 1/2" 8058399 7.291/2" x 1/2" 8058406 5.991/2" x 5/8" 8058442 7.691/2" x 3/4" 1290031 17.993/4" x 3/4" 8058460 14.99
Thread Size(JIC 37°x Metric)
Wt. (lbs.) ITEM PRICE
1/4" x 12 mm 0.1 8120610 3.493/8" x 14 mm 0.1 8120628 3.993/8" x 16 mm 0.1 8120636 4.493/8" x 18 mm 0.1 8120644 4.991/2" x 18 mm 0.1 8120651 4.995/8" x 20 mm 0.2 8120669 5.491/2" x 22 mm 0.2 8120677 5.99
Thread Size(JIC 37°x Metric)
Wt. (lbs.) ITEM PRICE
3/8" x 14 mm 0.1 8120776 11.993/8" x 16 mm 0.1 8120784 13.991/2" x 18 mm 0.2 8120800 19.995/8" x 20 mm 0.2 8120826 21.991/2" x 22 mm 0.2 8120842 23.99
MALE X FEMALE
MALE X FEMALE
01 Hydraulics 6/6/06 8:29 AM Page 37
38
O-RING BOSS x NPT SWIVEL ADAPTERS
TEFLON TAPE
Seals all threaded valve and pipejoints. Withstands pressures up to10,000 PSI.
Thread Size ITEM PRICE1/2" x 16 ft. 1250086 0.391/2" x 40 ft. 1250620 0.993/4" x 32 ft. 1250087 1.291" x 65 ft. 1250088 1.99
• Used extensively in skid steer loader market• Less pressure drop through coupler assembly• Flat face design for minimal spillage during connection and
disconnection• Female body does not have recessed cavity. Dirt, debris and oil
do not get trapped• All steel parts are zinc plated and yellow bichromated• Working pressure: -25° to 125°C (-13° to 257°F)
Ready in 15 working days* (for a maximum order of 5 pieces).
Special quotes can be provided fororders of 10 pieces or more!
*Delivery time is extra
CUSTOM BUILT STORAGE TANK with BAFFLE
FEATURES:• Can be built to any dimensions to fit most
applications• Over 50 possible port positions and 8 different
port sizes• Heavy 12-gauge steel construction• Interior baffle plate• Optional features include an oil temperature/level
gauge and filler/strainer breather cap assembly• Painted black and treated internally with a rust
preventative oil
For more information contact your local store, our National Call Centre at 1-800-665-8685,
or Gary Laws 1-204-654-5209
I will be setting up a hydraulic system and need to determine what size reservoir I should use?
A good rule of thumb to use when selecting a reservoir is 2 to 1. This means ifyour pump output is 10 GPM the reservoir should hold approximately 20gallons. Some other factors that may have an influence on this ratio are thesystems duty cycle, operating temperature and environment.
E 30º to 80º (86º to 176º) 3.15" M10 0.4 8093031 8.99
F 20º to 70º (68º to 158º) 5.0" M12 0.7 8093023 9.99
Mounts on the side of hydraulic reservoir tank.
OIL RESERVOIRS
Capacity(GAL.)
Ports (NPT)In x Out
O’all dim.H x L x W
Wt.(lbs.) ITEM PRICE
3.0 1-1/4" x 3/4"6.5" x 12" x 12.2" 18.7 1250040 99.995.0 1-1/4" x 3/4"8.3" x 12" x 16.2" 25.7 1250041 119.9910.0 1-1/4" x 1-1/4" 11.8" x 16" x 16.2" 38.4 1250043 149.99
Capacity(GAL.)
O’all dim.H x L x W
Wt.(lbs.) ITEM PRICE
15.0 19" x 16" x 16.2" 66.0 1250096 259.9925.0 20.4" x 16" x 24.2" 61.5 1250097 339.99
A) RESERVOIRS
C) 10 GALLON RESERVOIR WITH BAFFLE• Interior baffle between suction and discharge sides of tank• 4 ports
– two 1-1/4" NPT inlet/outlet ports– one 3/4" NPT bottom drain port– one 3/8" NPT port for pumps or motors with case drain
D) RESERVOIRS WITH BAFFLE• Interior baffle between suction and discharge sides of tank• 1/4 turn chrome breather/filler cap with 15 micron strainer
basket• Temperature/level gauge• 5 ports
– two 2" NPT suction ports– one 3/8" NPT port for pumps with case drain– one 3/4" NPT bottom drain port– one 1-1/4" NPT top mounted return port with steel down
tube to prevent aeration
B) 10 GALLON RESERVOIR WITH CLEANOUT• 6" cleanout port for easy contamination removal• Inlet/Outlet ports: 1-1/4" NPT• O'all dim:11.8"H x 16"L x 16.2"W8102493 – Wt. 38.9 lbs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20999
A
B
C
D
• 12-gauge steel construction• Cleaned and tested for leak free performance• Interior coated with rust preventative oil
Gallon ratings of the reservoirs are based upon a 75%usable volume.
01 Hydraulics 6/6/06 8:30 AM Page 40
41
OIL RESERVOIRS
• Installs in reservoirs and provides the operator with an in cab low oil level indicator light
• Slosh bucket on fluid level switch increases accuracy • Requires a 1" NPT port in the reservoir top• Indicator light presses into any 1/2" diameter hole. 8087777 – Wt. 0.7 lbs.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7999
12 VDC OIL LEVEL SENSOR KIT
RETURN LINE MANIFOLD
• Use to eliminate numerous returnlines back to the reservoir
• Made of 11-gauge steel• Has 6 ports, three 3/4" NPT, two 1"
NPT, and one 1/4" NPT port8076051 – Wt. 10.1 lbs. . . . . . . 8999
• Allows hydraulic fluid to be either heated or cooled
• Can also be used for many other applications where fluid heating or cooling is required
• Side oil inlet/outlet ports: 3/4" NPT• Top coolant inlet/outlet ports: 3/4" NPT
• The filter cart is designed for the filtering andtransferring of hydraulic oil
• Typical applications include the removal ofparticulate and water contamination from hydraulicoil, filtration of new oil prior to transferring it into ahydraulic reservoir and the emptying of a storagetank or reservoir
• By reconditioning your oil you promote longercomponent life, less downtime and longer intervalsbetween oil changes
WARNING: FAILURE OR IMPROPER SELECTION ORIMPROPER USE OF ANY OF THE HYDRAULIC PRODUCTSAND/OR SYSTEMS OR RELATED ITEMS CAN CAUSE DEATH,PERSONAL INJURY AND/OR PROPERTY DAMAGE.
01 Hydraulics 6/6/06 8:30 AM Page 41
42
MAGNETIC PLUGS
STAMPED STEEL PORTFLANGES
TANK FLANGES
• Square head design• Used to protect hydraulic systems
by magnetically collecting ferrous particles
• These port flanges make quick and easy work of adding a threaded port to a reservoir
• Just cut pilot hole in tank and weld on threadedport flange
GLYCERINE FILLED PRESSURE GAUGES• Provides longer life and reduces erratic needle movement• Scale shows PSI and Bar• Designed for rugged heavy service• 1/4" NPT thread• 2-1/2" face dia.
Mount Type Pressure Range Wt. (lbs.) ITEM PRICEA Vertical 0 to 2,000 PSI 0.5 8000833 12.99A Vertical 0 to 3,500 PSI 0.5 8000842 13.99A Vertical 0 to 5,000 PSI 0.5 8000851 14.99A Vertical 0 to 7,000 PSI 0.5 8000860 15.99B Horizontal 0 to 2,000 PSI 0.6 8000879 16.99B Horizontal 0 to 3,500 PSI 0.6 8000888 17.99B Horizontal 0 to 5,000 PSI 0.3 8000897 18.99B Horizontal 0 to 7,000 PSI 0.6 8000904 19.99
• Features an aluminum cylinder body andchromed steel shaft
• Max. continuous pressure: 130 PSI
BORE: 0.8" (20 MM) • Ports: 1/8" NPT• Rod dia.: 0.4" (10 mm)• Rod end threading: M8 x 1.25• Shaft end of cylinder tube: M20 x 1.5 threading (with nut)• Base end features M20 x 1.5 threaded tang (with nut)• Threaded tang: 0.4" (10 mm) wide with 0.3" (8 mm) cross hole
BORE: 1.6" (40 MM) • Ports: 1/4" NPT• Rod dia.: 0.6" (16 mm)• Rod end threading: M12 x 1.25• Foot mount brackets at each end of the cylinder housing with
BORE: 2.5" (63 MM) • Ports: 3/8" NPT• Rod dia.: 0.8" (20 mm)• Rod end threading: M16 x 1.5• Foot mount brackets at each end of the cylinder housing with 0.5"
(12 mm) dia. mounting holes spaced 2.2" (56 mm) apart• Can be used for power tailgate applications
BORE: 3.2" (80 MM) • Ports: 3/8" NPT• Rod dia.: 1" (25 mm)• Rod end threading: M20 x 1.5• Foot mount brackets at each end of the cylinder housing with 0.6"
(14 mm) dia. mounting holes spaced 2.8" (70 mm) apart• Can be used for power tailgate applications
01 Hydraulics 6/6/06 8:30 AM Page 45
46
A) FOR 1.6" (40 mm) BORE CYLINDERWt. 0.6 lbs.8071961 – .5" (12 mm pinhole) . . . . . . . . . . . . 999
B) FOR 2.5" (63 mm) BORE CYLINDERWt. 1.3 lbs.8064917 – .6" (16 mm pinhole) . . . . . . . . . . . . 999
C) FOR 3.1" (80 mm) BORE CYLINDERWt. 2.5 lbs.8091688 – .6" (16 mm pinhole) . . . . . . . . . . 1499
8 mm x 1.25 0.3" (8 mm) 0.3" (8 mm) 0.1 8041287 12.9910 mm x 1.25 0.4" (10 mm) 0.4" (10 mm) 0.2 8041295 13.9912 mm x 1.25 0.5" (12 mm) 0.5" (12 mm) 0.3 8004055 14.9916 mm x 1.5 0.6" (16 mm) 0.6" (16 mm) 0.7 8045122 21.9920 mm x 1.5 0.8" (20 mm) 0.8" (20 mm) 1.5 8091647 39.99
G
H
MALE TANG ENDS CLEVIS ENDS
MEMBER OF THE FLUID POWER SOCIETY
Can be used on the tie rod pneumatic cylinders tochange the rod end configuration.
PNEU
MAT
IC P
RODU
CTS
FLOAT JOINTS WITH FLANGEFloat joint will compensate up to 5°.
Threading Bolt HoleDia.
Mounting HolesCentre to Centre Flange Dim. Wt.
(lbs.) ITEM PRICE
J 8 mm x 1.25
0.3" (6.6 mm) 1.4" (36 mm) 1.9" x 0.7"
(48 x 19 mm) 0.2 8041311 24.99
J 10 mm x 1.25
0.3" (6.6 mm) 1.6" (40 mm) 2" x 1"
(52 x 25 mm) 0.3 8041329 26.99
J 12 mm x 1.25
0.4" (9 mm) 2.0" (52 mm) 2.8" x 1.3"
(70 x 32 mm) 0.8 8041337 28.99
K 16 mm x 1.5
0.4" (9 mm) 1.8" (45 mm) 2.6" x 2.6"
(65 x 65 mm) 1.5 8045148 44.99
K 20 mm x 1.5
0.4" (11 mm) 2.2" (55 mm) 3.0" x 3.0"
(75 x 75 mm) 2.9 8091670 49.99
I) SWIVEL EYESGrease nipple for easy lubrication.
Threading Thickness Pinhole Dia. Wt. (lbs.) ITEM PRICE8 mm x 1.25 0.5" (12 mm) 0.3" (8 mm) 0.1 8004014 9.9910 mm x 1.25 0.6" (16 mm) 0.4" (10 mm) 0.2 8041303 12.9912 mm x 1.25 0.6" (16 mm) 0.5" (12 mm) 0.3 8004015 14.9916 mm x 1.5 0.8" (21 mm) 0.6" (16 mm) 0.5 8045106 21.9920 mm x 1.5 1.0" (25 mm) 0.8" (20 mm) 0.9 8091662 26.99
I
J
K
01 Hydraulics 6/6/06 8:30 AM Page 46
47
PNEUMATIC PRODUCTS
LEVER CONTROL VALVESA) 5-WAY, 2-POSITION• Max. continuous pressure: 100 PSI• Max. continuous flow: 36 CFM• Ports: 1/4" NPT• Control 1 double or 2 single acting
Princess Auto currently has 8 MHTs working within our Retail Stores, Home Office andManufacturing. They work together with store Team Members that have completed their
Hydraulics Level 1 and Hydraulics Level 2 training program to help provide the customers withthe best possible hydraulic knowledge and service. We will be continuing our hydraulics
training in 2006-2007 to improve customer service.