www.khind.com.my P/N: 40-51042-00 This manual is also available online model/型号 DC228/ DC278/ DC348 Display Chiller /冷冻陈列柜 / Peti Pendingin Instruction Manual / 说明指示书/Buku Panduan Please read this manual carefully before operating this product. Keep this manual handy for future reference. 请在使用此产品前,详读此说明书。并将之收藏以作日后参考。 Sila baca buku panduan ini dengan teliti sebelum menggunakan produk ini. Simpanlah untuk rujukan masa depan. Important / 重要/Mustahak
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Please read this manual carefully before operating this product. Keep this manual handy for future reference.请在使用此产品前,详读此说明书。并将之收藏以作日后参考。
Sila baca buku panduan ini dengan teliti sebelum menggunakan produk ini. Simpanlah untuk rujukan masa depan.
Important / 重要/Mustahak
Parts identi�cation
Cleaning & Maintenance
1. Do not open the door frequently and too long to save energy.2. Never leave heavy or hot objects on top panel or the showcase to avoid deforming.3. Cut o� the power before cleaning.4. To clean the showcase ,please use soft cloth dampened in some moderate detergent. After cleaning ,wipe in dry ,never use all kinds of detergent and hot water. 5. Use warm water to clean oil fruit juice stain on the magnetic gasket in order to keep its elasticity.6. The showcase should not be left unused for a long time ,to stop using the showcase ,disconnect the main power �rst, then clean the inside and leave the door open for 2-3days to dry it.
Safety Precaution Information!
Safety & warning information 1. Top lamp Chimney2. Light Switch3. Handle4. Shelf5. Door6. Water Draining Hole7. Door Pad8. Foot Screw and Wheel9. Inner Light10. Circulator Fan11. Glass12. Heat Air Hole13. Thermostat
*Pictures are for illustration purpose only.
21
Control Panel
1. All repairs, disassembly and modi�cations must be performed by quali�ed technicians. Attempting to perform these operations by yourself can result in �re, mal-function and injury.2. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly quali�ed persons in order to avoid a hazard.3. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.4. Do not splash water directly onto unit or wash unit with water. These actions can result in short circuit or electrical leakage.5. Do not put in�ammable liquids or volatile substances into unit. Fire or explosion may occur.6. Do not modify, damage, excessively bend, strain, twist or bundle power cord. 7. Do not place heavy objects on power cord.8. This unit is intended to cool or store bottled water or canned beverages. Do not use this unit for other purposes as it can adversely a�ect performance.9. Do not attempt to insert �ngers or objects into air suction compartment.10. Do not place objects or items containing water on top of unit.11. If gas leakage is detected near or around unit, do not touch or open unit's door. Open windows or door to ventilate air. Find gas and plug leakage before operating the unit.12. Should the unit need to be placed in temporary storage, ensure that the location is not accessible to children. And lock or tape the door from opening. This will minimize risk of children trapped in the air tight compartment.13. When moving unit to another location always unplug from mains.14. Do not place more than 20 kg on top of each shelf. 15. Connecting the power to check the showcase before using. The showcase can be used when the temperature decreases obviously after 30 minutes.16. If power cut-o� is needed, you should wait for at least 5 min before plugging in again to avoid damage to the compressor.17. Adjust the dial according to the real room temperature, the quantity of the foodstu� stored.18. Hot food should be stored only after it is completely cold.19. Packing foods with plastic bag to avoid tastes mixing and frost.
* Speci�cations are subject to change without prior notice.
Model
Voltage
Power
Current
Net Capacity
Refrigerant
Net Weight
Gross Weight
Product Dimension (LxWxH)
Box Dimension (LxWxH)
DC228
220-240V~ 50Hz
230W
1.5A
228L
R134a(95g)
60kg
69kg
530 x 590 x 1730mm
575 x 625 x 1770mm
DC278
220-240V~ 50Hz
230W
1.6A
278L
R134a(100g)
64kg
73kg
600 x 590 x 1780mm
645 x 625 x 1821mm
DC348
220-240V~ 50Hz
260W
1.7A
348L
R134a(115g)
75kg
85kg
600 x 590 x 1930mm
645 x 625 x 1970mm
Speci�cations
19
11
12
10
13
3
4
5
7
8
6
2
1
2
34
5
6
70
The �gure on the thermostat 1 - 7 only indicates the temperature level fromhigh to low.
Installation Troubleshooting
1. When you transport the showcase, the angle between the compartment body and the ground should be no less than 45˚ and you should never place the showcase upside down.2. Do not use any of the external part as loading points, such as the door.3. When the showcase is installed or used, the entire package(lncluding board and foam plastic) should be got rid of.4. Keeping the showcase stable to avoid vibration and noise.5. The showcase should be installed in the place with good ventilation, A space of at least l 0cm should be allowed between the surrounding wall and the cabinet wall for air circulation.6. It should be placed far form heating resource and not under direct sunshine to avoid decrease of the e�ciency of refrigeration.7. Install the showcase in a dry place so as to prevent rust on the compartment body, which may a�ect the electric insulation.8. Water condensation may appear on the exterior and on the glass door during hot and humid days or depending on the place of installation. This is normal. Wipe away condensation with a dry soft cloth.
1. You can use the brakes on the wheels and/or the foot screws to stop moving of the showcase. 2. Remember to lift the brake and/or turn foot screws clockwise when moving the showcase.
3 4
How to Use Wheel & Foot Screw
1. There will be sound of �owing water when the refrigerant is running.2. When the environment humidity is too heigh ,there will be dew condensed on the surface of the showcase.3. While working ,the condenser and the compressor will be hot.
Do not cooling - The plug does not �t the socket well - The protector or the fuse has broken o� - The power is o�
Fit the plug well Change the fuse
Big noise - The placing base is too soft, or the unit is inclining - The wheels do not touch the �oor well - The cabinet is too close to the wall - There are other objects directly touching the unit
Mount wood at the bottom Adjust the wheel screw Keep a certain distance from thewall Take the objects away
There are smellsinside the unit
- The cool air exit is blocked - Food with strong smell is not packed
Take away the food near to the exit Pack the food well
The compressordoes not stop
- The food temperature is too high or there are too much food inside - Open the door too frequently or the door is not well closed - Directly under the sunshine or too close to the heat resource - The ventilation is not good
Put the food in after cooling orreduce the quantity Close the door tightly Keep o� the heat resource Keep certain space for ventilation
Reason SolutionWARNING! INSTALLATION SHOULD BE PERFORMED BY THE DEALER OR A QUALIFIED EXPERT.ATTEMPTING TO INSTALL THE UNIT YOURSELF COULD RESULT IN WATER LEAKAGE, REFRIGERANT
LEAKAGE, ELECTRIC SHOCK OR FIRE.
WARNING! DO NOT SWITCH ON THE DISPLAY CHILLER FOR 12 HOURS AFTER RECEIVING IT.
WARNING! RESTARTING THE UNIT IMMEDIATELY AFTER SWITCHING OFF POWER MAY CAUSE THE UNIT TO MAL-FUNCTION. WAIT 5 MINUTES BEFORE RESTARTING THE UNIT.
Tip
1. Do not allow items to obstruct the cold air inlets or the suction outlets.2. Placed items should not protrude from shelves.3. Make sure that there are adequate gaps between shelves for air circulation.4. Place items evenly on all shelves5. All items must be placed on shelves and not on bottom of compartment..
1. Cerobong lampu atas2. Suis Lampu3. Pemegang4. Rak5. Pintu6. Lubang Saliran Air7. Pad Pintu8. Skru Kaki dan Roda9. Cahaya Dalam10. Kipas Peredaran11. Kaca12. Lubang Udara Panas13. Termostat
*Gambar adalah untuk tujuan ilustrasi sahaja.
19
11
12
10
13
3
4
5
7
8
6
2
故障排除
问题
不冷却 - 插头与插座不匹配
- 保护器或保险丝已损坏
- 电源关闭
正确安装插头
更换保险丝
大噪音 - 放置底座太软,或装置倾斜
- 轮子不能很好地接触地板
- 柜子离墙壁太近了
- 还有其他物体直接接触电器
在底部安装木材
调整车轮螺丝
与墙壁保持一定的距离
把物体移开
柜内有异味 - 冷空气出口受阻
- 有强烈气味的食物没包装
带走出口附近的食物
包装好食物
压缩机不停止 - 食物温度过高或过过多食物
- 太频繁打开门或门没有很好的关闭
- 直接在阳光下或太靠近热源的地方
- 通风不好
待食物冷却后放入或减少食物数量
把门紧紧关上
保持远离热源
保持一定的通风空间
原因 解决方案
Maklumat Keselamatan!
Maklumat Keselamatan!
Maklumat keselamatan & amaran
1. Semua pembaikan, pemasangan dan pengubahsuaian mesti dilakukan oleh juruteknik yang berkelayakan. Cubaan untuk melaksanakan operasi ini sendiri boleh mengakibatkan kebakaran, kerosakan dan kecederaan.2. Sekiranya kabel bekalan rosak, ia mesti diganti oleh pengilang, ejen perkhidmatan atau pihak yang berkelayakan bagi mengelakkan bahaya.3. Perkakas ini bukan untuk digunakan oleh orang ( termasuk kanak-kanak ) yang kurang upaya fizikal, deria atau kecacatan mental, atau kurang pengalaman dan pengetahuan, melainkan mereka diberi perhatian atau tunjuk ajar berkaitan penggunaan perkakas oleh orang yang bertanggungjawab untuk keselamatan mereka. Kanak-kanak haruslah diperhatikan untuk memastikan mereka tidak bermain dengan perkakas ini.4. Jangan memercikkan air terus ke perkakas atau mencuci perkakas dengan air. Tindakan ini boleh mengakibatkan litar pintas atau kebocoran elektrik.5. Jangan letakkan cecair atau bahan mudah terbakar ke dalam perkakas. Kebakaran atau letupan mungkin berlaku.6. Jangan mengubah, merosakkan, terlalu bengkok, meregangan, putar atau mengikat kabel kuasa secara berlebihan.7. Jangan letakkan objek berat pada kabel kuasa.8. Perkakas ini bertujuan untuk menyejukkan atau menyimpan air botol atau minuman dalam tin. Jangan gunakan perkakas ini untuk tujuan lain kerana boleh menjejaskan prestasi.9. Jangan cuba memasukkan jari atau objek ke dalam ruang penyedut udara.10. Jangan letakkan objek atau barang yang mengandungi air di atas perkakas.11. Sekiranya kebocoran gas dikesan dekat atau di sekitar perkakas, jangan sentuh atau buka pintu perkakas.Buka tingkap atau pintu untuk pengudaraan udara. Mencari kebocoran gas dan sekatkan kebocoran sebelum mengendalikan perkakas. 12. Sekiranya perkakas perlu diletakkan di tempat simpanan sementara, pastikan lokasi tersebut tidak dapat dicapai oleh kanak-kanak. Kuncikan atau pita pintu dari pembukaan. Ini akan mengurangkan risiko kanak-kanak terperangkap di ruangan kedap udara.13. Semasa memindahkan perkakas ke tempat lain, sentiasa cabut plag dari soket elektrik.14. Jangan meletakkan lebih daripada 20 kg di atas setiap rak.15. Menyambungkan kuasa untuk memeriksa pameran sebelum menggunakan. Pameran boleh digunakan semasa suhu menurun dengan jelas setelah 30 minit.
16. Sekiranya pemotongan kuasa diperlukan, anda harus menunggu sekurang-kurangnya 5 minit sebelum memasang semula untuk mengelakkan kerosakan pada pemampat.17. Laraskan dail mengikut suhu bilik sebenar, kuantiti bahan makanan yang disimpan.18. Makanan panas harus disimpan hanya setelah sejuk sepenuhnya.19. Mengemas makanan dengan beg plastik untuk mengelakkan rasa bercampur dan beku.
Pembersihan & Penyelenggaraan
1. Jangan buka pintu dengan kerap dan terlalu lama untuk menjimatkan tenaga.2. Jangan sekali-kali meninggalkan objek berat atau panas di panel atas atau pameran untuk mengelakkan mengubah bentuk.3. Memotong kuasa sebelum pembersihan.4. Untuk membersihkan peti pendingin, gunakan kain lembut yang dibasahi dengan sedikit bahan pencuci sederhana. Selepas membersihkan, lap kering, jangan sekali-kali menggunakan semua jenis pencuci dan air panas. 5. Gunakan air suam untuk membersihkan noda jus buah atau minyak pada gasket magnet untuk mengekalkan keanjalannya.6. Peti pendingin tidak boleh dibiarkan tidak digunakan untuk masa yang lama, untuk berhenti menggunakan peti pendingin, putuskan kuasa utama, kemudian bersihkan bahagian dalam dan biarkan pintu terbuka selama 2-3 hari untuk mengeringkannya.
Panel kawalan
1
2
34
5
6
70
Angka pada termostat 1 - 7 hanya menunjukkan suhu tahap dari tinggi ke rendah.
Pemasangan
Pemasangan
1. Apabila anda mengangkut peti pendingin, sudut antara badan petak dan tanah tidak boleh kurang dari 45˚ dan anda tidak boleh meletakkan peti pendingin itu terbalik.2. Jangan gunakan bahagian luaran sebagai tempat memuat, seperti pintu.3. Semasa peti pendingin dipasang atau digunakan, keseluruhan bungkusan (termasuk papan dan plastik busa) perlu diambilkan.4. Jaga kestabilan peti pendingin untuk mengelakkan getaran dan kebisingan.5. Peti pendingin hendaklah dipasang di tempat dengan pengudaraan yang baik, Ruang sekurang-kurangnya 10cm hendaklah dibenarkan antara dinding sekeliling dan dinding kabinet untuk peredaran udara.6. Ia perlu diletakkan jauh dari sumber pemanasan dan tidak di bawah cahaya matahari langsung untuk mengelakkan penurunan kecekapan penyejukan.7. Pasang peti pendingin di tempat yang kering untuk mengelakkan karat pada badan petak, yang boleh menyebabkan penebat elektrik.8. Pemeluwapan air mungkin muncul di bahagian luar dan di pintu kaca semasa hari panas dan lembap atau bergantung pada tempat pemasangannya. Ini adalah biasa. Lap pemeluwapan dengan kain lembut kering.
1. Anda boleh menggunakan brek pada roda dan / atau skru kaki untuk hentikan pergerakan peti pendingin.2. Ingatlah untuk mengangkat brek dan / atau putar skru kaki mengikut arah jam semasa menggerakkan peti pendingin.
Cara Menggunakan Roda & Skru Kaki
AMARAN! PEMASANGAN PERLU DILAKUKAN OLEH PENGEDAR ATAU PAKAR KELAYAKAN.CUBA UNTUK MEMASANG PERKAKAS SENDIRI BOLEH MENYEBABKAN KEBOCORAN AIR,
KEBOCORAN PENDINGIN, KEJUTAN ELEKTRIK ATAU KEBAKARAN
AMARAN! JANGAN HIDUPKAN PETI PENDINGIN SELAMA 12 JAM SELEPAS MENERIMANYA.
AMARAN! MEMULAKAN SEMULA PERKAKAS SEGERA SELEPAS MEMATIKAN KUASA MUNGKIN MENYEBABKAN PERKAKAS ROSAK. TUNGGU 5 MINIT SEBELUM MEMULAKAN SEMULA
PERKAKAS.
* Perubahan spesifikasi boleh dilakukan tanpa sebarang notis.
ModelVoltanKuasaArusKapasiti BersihGas PenyejukBerat BersihBerat KasarDimensi Produk (LxWxH)Dimensi Kotak (LxWxH)
DC228220-240V~ 50Hz
230W1.5A228L
R134a(95g)60kg69kg
530 x 590 x 1730mm575 x 625 x 1770mm
DC278220-240V~ 50Hz
230W1.6A278L
R134a(100g)64kg73kg
600 x 590 x 1780mm645 x 625 x 1821mm
DC348220-240V~ 50Hz
260W1.7A348L
R134a(115g)75kg85kg
600 x 590 x 1930mm645 x 625 x 1970mm
Spesifikasi
9 10
Penyelesaian masalah
Masalah
Tanpa penyejukan - Palam tidak sesuai dengan soket- Pelindung atau fius telah rosak- Kuasa dimatikan
Pasangkan plag dengan baikTukar fius
Bunyi besar - Pangkalan meletakkan terlalu lembut, atau perkakas ini condong.- Roda tidak menyentuh lantai dengan baik- Kabinet terlalu dekat dengan dinding- Terdapat objek lain secara langsung menyentuh perkakas
Pasang kayu di bahagian bawahLaraskan skru rodaJauhkan jarak tertentu daripadadindingMengambil dan jauhkan objek
Terdapat bau di dalam perkakas
- Udara keluar sejuk disekat- Makanan dengan bau yang kuat tidak dibungkus
Keluarkan makanan berhampiran udara keluar sejukBungkuskan makanan dengan baik
Pemampat tidak berhenti
- Suhu makanan terlalu tinggi atau terlalu banyak makanan di dalam- Buka pintu terlalu kerap atau pintu tidak ditutup dengan baik- Secara langsung di bawah cahaya matahari atau terlalu dekat dengan sumber panas- Pengudaraan tidak baik
Masukkan makanan setelah sejuk atau kurangkan kuantiti makananTutup pintu dengan rapatJauhkan dari sumber panasPastikan ruang tertentu untuk pengudaraan
Sebab Penyelesaian
1. Akan ada bunyi air mengalir ketika gas pendingin sedang beroperasi.2. Apabila kelembapan persekitaran terlalu tinggi, akan ada embun pekat pada permukaan peti pendingin.3. Semasa bekerja, kondensor dan pemampat akan panas.
Catatan:
Tips
1. Jangan biarkan barang menghalang saluran masuk udara sejuk atau saluran penyedut.2. Barang yang diletak tidak boleh menonjol dari rak.3. Pastikan terdapat jurang yang mencukupi antara rak untuk peredaran udara.4. Letakkan barang secara merata di semua rak.5. Semua barang mesti diletakkan di rak dan bukan di bahagian bawah petak.