目录 8 in 1 Sensor ◆ 8 in 1 Sensor Unique Features ● Built in PIR motion sensor and light intensity sensor ● Built in 2 Dry Input Ports ● Built in 32 Logics.

目录8 in 1 Sensor

◆8 in 1 SensorUnique Features

●Built in PIR motion sensor and light intensity sensor●Built in 2 Dry Input Ports●Built in 32 Logics●Infrared receiver●Infrared transmitter●Built in security alarm logic (work with Security Module)

Subnet ID and Device ID

Remark

MAC Address

Basic information

1.Input key target Qty

3.Select IR code from database

2.Select key no.

4.Downlaod

5.Confirm

IR Code download

6.Select key no.

7. Select key stroke type

IR Code testing 8. Press Transmit and test

IR Code receiving

1.Configuration same as switch panel, first select key no. of remoter

2.Setup the mode for the key

3.Select key control mode

4.Save

IR Code receiving

5.Select control target

IR Code receiving

6.Input target Subnet ID, Device ID and Parameter

7. Save

IR Code receiving

IR Code receiving

8. Align the Remoter with 8 in 1 sensor, press the key and test

1. Select a Logic Block (Max 32 blocks)

2.Input Remark and charge the status to Valid, default is invalid

3. Save

4.Click Edit to setup menu

Automation logics configuration

Automation logics configuration

Current statusSelect logic condition Select logics

relation

Command

Application

In case of a meeting room has below requirements:

1.When people open the door and come in the meeting room, the lights open automatically2. After people come in the room for more than 1 minute, open the AC and change the temperature to 25℃3. After people leave the room for 1 minute, off the lights and the temperature increase 2℃4.After people leave the room for 3 minute,turn off the AC automaticallyWe need 4 logic blocks to accomplish the requirements above

1.When people open the door and come in the meeting room, the lights open automatically

Requirements

2. Input remark and change current status to Valid

3.Save

4.Edit Logic setting

1.Select a Logic block

Requirement: When people open the door and come in the meeting room, the lights open automatically

5.If the door installed a magnetic contact and connect to 8 in 1 sensor, change condition to disconnect

6. Select Motion sensor and Condition movement

7. Change delay time to 0 sec.

8.Select relation And

9.Save logic setting

10.Click Command to select control target

11. Input light channel to open

12.Save

Requirement: When people open the door and come in the meeting room, the lights open automatically

2. After people come in the room for more than 1 minute, open the AC and change the temperature to 25℃

Requirements

Requirement: After people come in the room for more than 1 minute, open the AC and change the temperature to 25℃

2. Input remark and change current status to Valid

3.Save

4.Edit Logic setting

1.Select a Logic block

5.If the door installed a magnetic contact and connect to 8 in 1 sensor, change condition to disconnect

6. Select Motion sensor and Condition movement

7. Change delay time to 1 minutes

8.Select relation And

9.Save logic setting

10.Click Command to select control target

Requirement: After people come in the room for more than 1 minute, open the AC and change the temperature to 25℃

12.Input target with the subnet ID and device ID of the sensor. Type “Infrared remote sensor", parameter 1 “3”, parameter 2 “on”

13.SaveRequirement: After people come in the room for more than 1 minute, open the AC and change the temperature to 25℃

11.Before set the control target, please go to IR transmitter page and record the key no.(3) of 25℃

3. After people leave the room for 1 minute, off the lights and the temperature increase 2℃

Requirements

2. Input remark and change current status to Valid

3.Save

4.Edit Logic setting

1.Select a Logic block

Requirement: After people leave the room for 1 minute, off the lights and the temperature increase 2℃

Requirement: After people leave the room for 1 minute, off the lights and the temperature increase 2℃

5.Select Motion sensor and Condition No movement

6.Change delay time to 1 minutes

7.Select either AND or OR because there’s only one logic condition

8.Save logic setting

9.Click Command to select control target

10.Input target with the subnet ID and device ID of the sensor. Type “Infrared remote sensor", parameter 1 “5”, parameter 2 “on”

11.Save Requirement: After people leave the room for 1 minute, off the lights and the temperature increase 2℃

4.After people leave the room for 3 minute, turn off the AC automatically

Requirements

2. Input remark and change current status to Valid

3.Save

4.Edit Logic setting

1.Select a Logic block

Requirement: After people leave the room for 3 minute, turn off the AC automatically

5.Select Motion sensor and Condition No movement

6.Change delay time to 3 minutes

7.Select either AND or OR because there’s only one logic condition

8.Save logic setting

9.Click Command to select control target

Requirement: After people leave the room for 3 minute, turn off the AC automatically

10.Input control target

11. SaveRequirement: After people leave the room for 3 minute, turn off the AC automatically

Complete