Transcript
X-Ray Inspection of BGAs
November 2017
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
X-Ray Inspection-BGAs IPC-A-610 G Criteria
You DO NOT HAVE to x-ray BGAs according to the IPC-A-610G
CHOICEA.Develop process. Validate process using x-ray. Sample plan inspection. Need to have objective
evidenceOR
B. Inspect via x-ray
Note: X-ray equipment not intended for electronic assemblies or not properly set up can damage sensitive assemblies
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Collapsing Soldering Balls
Note 1. Design induced voids, e.g., microvia in land, are excluded from this criteria. In such cases acceptance criteria shall be established between the manufacturer and user.
Note 2. Manufacturers may use test or analysis to develop alternate acceptance criteria for voiding that consider the end-use environment.
Feature Classes 1,2,3 X-Ray
Alignment Solder ball offset does not violate minimum electrical clearance.
Can scan to see separation of balls or use built-in metrology tools
Solder Ball Spacing
Solder ball offset does not violate minimum electrical clearance.
Can scan to see separation of balls or use built-in metrology tools
Soldered Connections
No solder bridging; BGA solder balls contact and wet to the land forming a continuous elliptical round or pillar connection.
No non-common connections of solder balls. Telltale sign is same ball volume/area based on min amd max set oints
Voids 30% or less voiding of any ball in the x-ray image area.1,2
Modern x-ray can measure
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Non-Collapsing Soldering Balls
Note 1. Design induced voids, e.g., microvia in land, are excluded from this criteria. In such cases acceptance criteria shall be established between the manufacturer and user.
Note 2. Manufacturers may use test or analysis to develop alternate acceptance criteria for voiding that consider the end-use environment.
Feature Classes 1,2,3 X-Ray
Alignment Solder ball offset does not violate minimum electrical clearance.
Can scan to see separation of balls or use built-in metrology tools
Soldered Connections
No solder bridging; BGA solder balls contact and wet to the land forming a continuous elliptical round or pillar connection.
No non-common connections of solder balls. Telltale sign is same ball volume/area based on min and max set points
Voids No to little voiding
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
IPC-7095 Inspection Guidelines
NOTE: These are guidelines (suggestions)
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Oblique View
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Know What You Are Looking For
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Know What You Are Looking For
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Open
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Short
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Short
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Broken Wire Bond
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Voiding
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Starved Solder Joint
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Non Uniform Collapse
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Solder Anomolies
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Uneven HeatingSmaller
Larger
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
Measurement and QC
Your BEST choice in PCB Test/ Rework/Repair and Solder Training & Tools www.solder.net
iPhone 4 Example
solder.netinfo@solder.net
X-Ray Inspection of BGAs
top related