Volume I, Issue 6 October 1 2015 - Middle River Yacht Club · 2015-12-28 · Summer is over and Fall has begun. Base-ball in winding down and Football has begun—and the Tiki bar
Post on 09-Aug-2020
0 Views
Preview:
Transcript
Summer is over and Fall has begun. Base-ball in winding down and Football has begun—and the Tiki bar is the place to be for Game Day. Boating days are still in high demand so let’s get the last few days on the water
while we can enjoy it. We started a new section in the newsletter regarding boat safety and maintenance tips (usually from Boat US) Hope you enjoy this month’s edition.
Happy OctoberFest !!
MIDDLE RIVER YACHT CLUB
October 1 2015 Volume I, Issue 6
The Scuttlebutt MRYC Newsletter
Inside this Issue
Elected Positions Appointed Positions
2
Officers Notes 3,4
Joke, Drink of the Month
6,7
Recipe, Word of the Month
8,9
Upcoming Events 10
Current Events 12
Bilge Pump Basics 20
Calendar 28
Honorary Members 30
Past Commodores 31
Ball Schedule 26
Boater Ditty Bag 25
Officers and Board of Directors
Committees and Other Positions
Page 2 The Scuttlebutt
Commodore Jack Lewis 410-960-7585 marialewis398@gmail.com Vice Commodore Ted Wooden 443-277-8005 ted@wilmotmodular.com Rear Commodore Kyle Gray 443-324-1997 kylecgray@aol.com Fleet Captain Dale Amato 443-928-7345 bigdaddyshrinkwrap@gmail.com Treasurer PC Larry Vinck 410-382-4711 lvinck@comcast.com Secretary Lee Klima 410-961-8777 sailor17.lee@gmail.com Board Member PC Ray Adey 410-960-2960 gypsysailor80@aol.com Board Member Paul Brown 443-463-6888 pab4364@comcast.net
Club Chaplain Ron Lippa 443-841-4377 rlippa@aol.com Communications Kyle Gray 443-324-1997 kylecgray@aol.com Tiki Bar Enhancements Norm Vokovsky 410-852-6177 nvacovsky@gmail.com Bar Manager Rob Bob Gilman 410-207-0478 robbob1686@gmail.com Pier Manager Jim Hart 443-850-2631 jk.hart@ngc.com Newsletter Editor Adam Bell 443-838-5361 abell21154@gmail.com Sergeant at Arms Chuck Gilman 410-322-3713 chuckgilman1@comcast.net Slip Committee Dave Justice 443-992-8743 davejusticeboat@gmail.com CCC Delegate PC Dottie Capp 410-633-9623 CBYCA Delegate Kyle Gray 443-324-1997 kylecgray@aol.com YCM Delegate PC Joe Vislocky 717-659-0563 jvislocky@jsvislocky.com Event Book Anita Lippa 443-841-4378
Page 3 Volume I, Issue 6
Vice-Commodore Ted Wooden
looking for people to help with the three C's ball. We need people to come up with a theme and help deco-rate our hospitality room as well as help in greeting other clubs when they come in to visit us. We are also looking for skit and song ideas for the Fri-day night show. It is going to be a great time with lots of fun people.
I have put up a sign up sheet on the bulletin board for people that want to help.
V/C Ted
Hello fellow club mem-bers. This summer has flown by so quickly I hope that everyone had a great one. It is hard to believe that ball sea-son is here upon us so quickly. Laura and I will be attending as many balls as possible to rep-resent Middle River Yacht Club in a positive way. As announced at our September mem-bership meeting we are
My time as Commodore is winding down and I thought maybe “just one more” year - just kidding. I have been putting the nominating committee together to make nomi-nations for next year’s bridge. It has been a fan-
tastic year and I want to thank everyone for their support. Many improvements have been made to the club and I hope everyone enjoys them. Our St. Michaels cruise was ex-cellent and I hope more
folks join us next year.
Thank You,
Commodore Jack
Commodore Jack Lewis
MRYC Email Addresses
commodore@middleriveryachtclub.com
vicecommodore@middleriveryachtclub.com
rearcommodore@middleriveryachtclub.com
fleetcaptain@middleriveryachtclub.com
newsletter@middleriveryachtclub.com
ipc@middleriveryachtclub.com
info@middleriveryachtclub.com
Page 4 The Scuttlebutt
Well what a fun boating season it has been. More members moved their boats this year than ever, we had a few raft ups (unfortunately it seemed like schedules always crossed paths when wanting to do more of them) and our annual Labor Day trip to St. Michael’s was one of the best ever. We had 6 boats that left Middle River on Friday of Labor Day weekend who made the trip down to St. Michael’s. And if you include Jim Hart driving his car down to spend some time with us, that would be 7. The weekend weather was perfect and we started with cock-tails and munchies on Commodore Jack and Maria’s boat, the “Wicked Lady” with a record number of people who climbed onboard for the festivities! And then from
there…well you can probably guess…Carpenter’s Street Saloon for bloody marys and many other libations being consumed! While the ladies did their usual shopping, the guys decided they needed “just one more!” so they hung out either on their boats or in Carpenter’s Street. We then all gathered back at Carpenter’s Street Saloon for a toast to a few of those members that we have recently lost, Terry Birmingham, Babe Ady and Bill Blondell, Sr. And the weekend continued with a lot more festivi-ties and fun from boat hopping, bar hopping, dancing, singing, shot ski, lots of laughs, awesome dinners and food, and great friendships being made over a few late night cocktails hanging out on the boats. There were a few stumbles along
the way such as “Waterfront Proper-ty” lost its air conditioning…only for a short time; luckily a friend had a spare pump that we could borrow and the “La Re Viera” sprung a leak! Again, with the help of friends, that was able to be fixed as well. All in all it was an awesome weekend! Then Monday came and Fleet and Fleetie brought us home safe and sound, but again not without some issues but we made it! Hopefully we will have more members who want to join us next year for this trip as we cannot wait to go back! A good time was had by all…hope you enjoy some of the photos that were taken from the weekend! Fleet Captain Dale
Fleet Captain Dale Amato
Princess Amelia Gray
most likely be cancelled due to the hurricane but I'm keeping hope alive! I only have a little over a month left as Princess of MRYC and while I'm sad to let it go it was such an honor and truly and amaz-ing experience being able to repre-sent MRYC. I will be attending Red Eye Yacht Club’s ball on October 10th and that will likely, unfortu-nately, be my last event as your princess. I hope you all will be able to attend my de-crowning and Rachel's crowning ceremony on November 8th. I'm excited for her to represent MRYC for a THIRD year. I hope I continue to receive your support through out
the end of this journey as reigning princess, as well as after my reign is over in this other journey we all like to call life. I love all of you and I'm looking forward to seeing you in the upcoming month. Its football season, let's get excited! Love always, MRYC Princess Amelia
Hi everyone! Princess here. I hope you all are adjusting to this not so warm any-more weather. Its terrible isn't it? But at least it isn't snowing yet. While college and work is taking up most of my time I try to come down to the club as often as I can. As most of you know my 21st birthday is on Sunday!! Woohoo! As always I will represent the club with the utmost respect and honor. As it is a privilege to be your Prin-cess, I will represent my self and the club as such. More than likely my birthday plans of attending the last Orioles game of the season will
Christmas and New Years. This is an opportunity to give back and be involved in designing a good time for all members.
I also want to remind you about the "Making Strides for Breast Cancer Cures" being held on Oct 18th off site but will have a huge impact on women around the
I felt a chill the other day which has me looking at the trees to see a change of colors. This tells me the holiday season is nearing. Halloween is first... I don't need to tell you the rest, do I? Let's embrace it! Holiday season is party season; each party needs leaders, each leader needs a committee. We need just a few peo-ple who want to be in a committee to cover social events of Halloween,
world. I will send out another email reminder to donate and/or walk with fellow club members to bring awareness to our community and throughout Baltimore.
PS... keep your sweater in your car/boat ;-)
R/C Kyle
Rear Commodore Kyle Gray
will send all pertinent information that the Officers and committee chairs request that I send out to the mem-bership via email. There may be infor-mation in these emails that do not appear on
I would like to wel-come all of the mem-bers who have recently joined Middle River Yacht Club. We try to keep all of our mem-bers informed with the happenings and plans around the club. We
our MRYC website. Please ensure we have your email address in our distribution list. Thank you, R/C Kyle Gray
Communications
Page 5 Volume I, Issue 6
Newsletter Editor
other information to newslet-ter@middleriveryachtclub.com. Please feel free to send sugges-tions, comments, and feedback as well. We can all contribute and make this a useful tool. Thank you, Adam Bell
This newsletter was created to help communicate the events in MRYC and other current infor-mation. If you have a submis-sion for this monthly newsletter please email it to me no later than the 20th of each month. It may not make it into the publi-cation otherwise—I’ll do my best. Please send any articles, ads, or
Help keep the club roster current.
Please email membership information updates to our Communications Liaison
Kyle Gray kylecgray@aol.com
443-465-7357 All information for Birthdays and Anniversaries
in this newsletter are collected from the club roster. Please check it for correctness.
Page 6 The Scuttlebutt MRYC Newsletter
Page 6 The Scuttlebutt
Joke of the Month
Page 7 Volume I, Issue 6
Drink of the Month: Bleed Purple
Ingredients: 3 oz. Vodka 1 1/2 oz. Cranberry juice 1/2 oz. Blue Curacao 1/2 oz. sour mix 1/2 oz. Sprite Direc ons: Rim the glass with sugar.
Gently shake and serve.
Add more Blue Curacao if it isn’t purple enough for you. Or try
grape pucker.
Page 8 The Scuttlebutt
Ingredients: for the dough
500 grams of flour
90 ml of extra virgin olive oil
200 ml of warm dry white
wine
2 tsp of salt
Recipe of the Month: Beautiful and Sunny Spinach Pie
Directions: 1. Mix all the ingredients for the dough and work the dough un l it
becomes uniform (using a mixer or not).
2. Cover it with plas c wrap while preparing the stuffing.
3. Boil the spinach and squeeze it to eliminate the water.
4. Cut it with a sharp knife to facilitate.
5. Mix it with the rico a cheese.
6. Add the egg.
7. Add the grated cheese, salt and pepper.
8. Amalgamate all ingredients.
9. Preheat the oven to 180°C/356°F.
10. Divide the dough in two. 11. Create 2 circles of 30cm/11.8in each using a rolling pin.
12. Place the 1st dough circle on baking paper. 13. Spread some breadcrumbs on it.
14. Place part of the stuffing in the center of the circle and the re‐
maining crea ng another circle around, as seen on the photos.
15. Cover it with the 2nd circle of dough. 16. Wet the borders and a ach one to another using a fork.
17. Place a small bowl over the central stuffing and punch with a
fork all around.
18. Using a sharp knife cut the borders in 3cm/1.2in slices.
19. Turn them upside 90°. 20. Bake for 30 minutes in preheated oven at 180°C/356°F.
Source: http://inspiredreamer.com/a-beautiful-and-sunny-spinach-pie/
for the stuffing
350 grams of boiled spinach
350 grams of rico a cheese
1 egg
100 grams of grated Parmigiano
Reggiano cheese
salt
Pepper breadcrumbs
Page 9 Volume I, Issue 6
Page 9 VolumWord of the Month: Embrace
Embrace (full definition) verb em·brace \im-ˈbrās\ : to hold someone in your arms as a way of expressing love or friendship : to accept (something or someone) readily or gladly : to use (an opportunity) eagerly Just like many words in our language, embrace has multiple meanings. Today I want to focus on embracing involvement. Whether it's Making Strides for Breast Cancer Cures or being on a committee at MRYC to organize and set-up club events or parties... embracing these actions are not only personal re-wards but rewards for those you impact by your actions. We have the oppor-tunity to give back to our members and people around the world if we just embrace being a helping hand in some aspect of our fortunate lives. We are blessed to have such a wonderful water community... gratitude and acts of kindness through leadership, involvement and selflessness are powerful trig-gers in life that bring happiness to many... 1. a: to take up especially readily or gladly <embrace a cause> b: to avail oneself of : welcome <embraced the opportunity to study further> 2. a: to take in or include as a part, item, or element of a more inclusive whole <charity embraces all acts that contribute to human welfare> b: to be equal or equivalent to <his assets embraced $10>
Page 10 The Scuttlebutt
The fund raising starts now and ends with
the Celebration Walk on October 18,2015.
Making Strides Against Breast Cancer means a great deal to Alison and me, and we appreciate anything and everything
that the club can do to help us reach our goal!
http://main.acsevents.org/site/TR/MakingStridesAgainstBreastCancer/MSABCCY15SA?
px=40913277&pg=personal&fr_id=70204
In the May membership meeting Paul Brown generously donated $1500.00 toward the bar stools in the main club
house.
The membership agreed to help Paul with the cause, donate, and walk in this event.
I know MRYC will stand up and join in.
We all committed to support this cause in any way we can—donations and/or walking
Page 11 Volume I, Issue 6
A thank you note from Joan Birmingham to the members of Middle River Yacht Club.
My family and I would like to thanks you for the touching card and beautiful planter you sent following the loss of my husband. We especially appreciate the current officers and all past Commodores that came in uniform to hon-or Terry. What an outpouring of love filled that room for my husband. I will forever be grateful to everyone who attended his memorial. Many thanks, Joan Birmingham.
Page 12 The Scuttlebutt
Here’s a few pictures from the Grand drawing day and Ravens Tailgate party at MRYC. What a great day and so many folks showed up to party. The Tiki bar truly is an asset to MRYC.
Page 13 Volume I, Issue 6
Page 14 The Scuttlebutt
Page 15 Volume I, Issue 6
Page 16 The Scuttlebutt
Page 17 Volume I, Issue 6
Hanging around the Pier at Higgins Yacht Yard during the St. Michaels annual MRYC Cruise.
Page 18 The Scuttlebutt
The afternoon in the Carpenter Street Saloon at St. Michaels
Page 19 Volume I, Issue 6
More Dinner and Drinks. Actually that never really ended for the en-tire weekend.
Page 20 The Scuttlebutt
Bilge Pump Basics They're your last line of defense against sinking, so give them some respect and a little love from time to time.
Due to the lack of maintenance they receive from the average boat owner, I often refer to bilge pumps as the Rodney Dangerfield of boat equipment, meaning "they just don't get no respect." It's a funny but also troubling statement, particularly be-cause bilge pumps are often a boat owner's first and only line of defense against sinking. To prevent you from being that proverbial scared sailor with a bucket, here's a look at bilge pump basics — from what they do, to selection, installation, and maintenance.
Page 21 Volume I, Issue 6
What Type Of Bilge Pump Do You Have? The most common types of bilge pumps (and the primary focus of this article) are centrifugal and dia-phragm electrical pumps. Centrifugal pumps move water by kinetic energy using a rotating, solid impeller, similar in design to a turbine. Water enters the pump, picks up speed as the impeller rotates, and is then forced out by its own momentum. Centrifugal pumps are submersible but not self-priming, meaning they must be sitting in water in order to pump it.
Centrifugal pumps are relatively inexpensive and can move a lot of water. Other advantages include low maintenance, excellent reliability, and the ability to pass small amounts of debris without clogging. They can also run dry for extended periods without damage, although this does wear the bearing and will cause it to fail eventually. Disadvantages include their inability to self-prime and their loss of effectiveness the farther they have to push water vertically.
A diaphragm pump acts like a little wet-vac to suck out bilge water. Water is pulled in through an intake valve, then pushed out through an output valve. Diaphragm pumps are self-priming (meaning they devel-op suction and prime themselves when dry), can be run dry without damage, and are better able to push water uphill than centrifugal pumps. As to downsides, they can't move as much water as a comparable centrifugal pump and most can't tolerate even small bits of trash or debris, which can lodge in the pump's valves, causing leaks or failure.
Nothing beats the simplicity and pumping power of a centrifugal pump. However, diaphragm pumps can be a better choice where water has to be pumped more than a few feet uphill, and they can be installed in a drier, more convenient place than the bottom of the bilge. Adding a filter before the pump to remove de-bris reduces the risk of failure.
What They Are (And Aren't) The primary job of most bilge pumps on most boats is to clear nuisance water from the bilges (packing gland drips, spray from an errant wave, etc.). The one that came with your boat may be up to that task, but a bilge pump should also be able to provide crucial extra time if your boat is taking on water, allowing you to find and deal with the source of a leak or, in extremis, to don life jackets and hopefully keep your boat afloat long enough for help to arrive. Most people upgrade to a larger bilge pump or add a backup bilge pump to give them time to deal with an emergency. Even that pump should not be confused with an emergency pump, which provides much greater dewatering capacity. If you plan on fishing the Canyons or sailing offshore, then you need a true "crash" pump, one that can move hundreds of gallons per minute.
This article will focus on the middle of these three options — the bilge pump meant to remove nui-sance water but also to give you time to deal with an emergency. See the article "Bilge Pump Capaci-ty: Do The Math" to figure out how much pumping capacity you need.
Page 22 The Scuttlebutt
Are Your Bilge Pumps Installed To Minimize Problems? The first step on the path to bilge pump nirvana is making sure your boat's bilge is clean and free of trash and debris. Routine bilge cleaning is a fact of life for older boats, but even that new boat you're purchas-ing can have a bilge littered with pump-clogging bits of construction material — wood shavings, bits of fiberglass, and gobs of epoxy. Oily bilge residue should also be cleaned up and disposed of properly. In addition to the ecological concerns of accidentally pumping it overboard, oil combines with dirt to form a gooey sludge that can clog pumps and prevent float switches from operating properly. In addition, some
No pump can work properly in a bilge choked with trash and debris.
Oil combines with dirt to form a gooey sludge that can clog pumps and prevent float switches from operating.
Do You Have Enough Capacity? Now that you know how different bilge pumps work, the next step is determining how many and what size your boat should have. The first thing to understand when shopping for a bilge pump is that just because a pump is rated to pump 1,000 gallons per hour (gph) that doesn't mean it will. See the "Bilge Pump Capacity: Do The Math" to figure out how much a bilge pump is likely to actually move when installed on your boat compared to its rated capacity.
So how much pumping capacity should your boat have? It's a good question, but one with no clear or easy an-swer, mainly because boats are so different. Any compartment that's essentially watertight (i.e. where water can't drain into another area) should have its own pump or two. While the American Boat and Yacht Council (ABYC) hasn't set requirements concerning bilge pump capacity, the American Bureau of Shipping recom-mends one 24-gallon-per-minute (gpm) pump — or about 1,440 gph — and one 12-gpm (720 gph) pump for boats under 65 feet. To me, it's a simple case of bigger is better — within reason, of course. Based on size alone, I'd recommend a minimum of 5,500 gph pumping capacity for a 40-foot vessel, divided among a 1,500-gph primary pump and two 2,000-gph backup pumps. I'd also throw a high-volume manual pump in the mix for good measure, since all that pumping capacity will be useless if something happens to your batteries.
Page 23 Volume I, Issue 6
Use smooth-walled marine-grade hose for pump discharge runs and secure them at each end with marine-grade stainless steel hose clamps. Hoses should be routed as directly as possible to their discharge thru-hull and should also be properly supported (approximately every 18 inches) to prevent chafe and excessive movement. Speaking of discharge thru-hulls, they should be situated well above the waterline to prevent water from siphoning back into the bilge. Siphon breaks and riser loops are also recommended and should reach at least 18 inches above static waterline where possible.
If your bilge pump uses a flapper style automatic float switch, it must be securely mounted and installed so that the floating-arm is clear of wires, hoses and other obstructions that could impede its operation. Orient the switch fore and aft, with the flapper pointed toward the stern. This is especially important on powerboats — during jackrabbit takeoffs, surging bilge water can damage the flapper mechanism. Installing them close to a bulkhead or frame also helps protect the switch from a torrent of water. Enclosed switches eliminate this worry, but they're difficult to inspect and test. Regardless of the type you choose, make sure each pump has a manual switch as well; none of the automatic systems are failsafe.
Make sure all bilge pumps not only have intake strainers or strum boxes installed, but that they can be easily reached and cleared of debris. As a marine surveyor I often see centrifugal-style pumps mounted beneath engines and completely inaccessible, even to simply clean the strainer — if your boat has similarly inacces-sible pumps, relocate them for better access.
Common bilge pump problems include physical damage, loose hoses, and failure to securely mount the pump to ensure proper orientation.
Page 24 The Scuttlebutt
ABYC standards require circuit protection for each bilge pump. You can do this by powering them through the primary DC circuit breaker panel, but then you'll have the potential problem of someone inadvertently killing power to the pumps by turning off the primary battery switch. To prevent this, you can also wire each through a dedicated fuse to the "all" or hot terminal of the battery switch (the one that's always energized) or even directly to the battery itself. The battery switch option ensures the pump can draw power from both batteries, rather than limiting them to one. An even better option is in-stalling a small, dedicated bilge pump breaker panel (which has the added benefit of keeping all bilge pump fuses and breakers together and easily accessible). This panel would then be wired directly to the battery switch, bypassing the primary DC circuit breaker panel.
When wiring your bilge pump, ensure all electrical connections are located well above normal bilge wa-ter levels (to reduce corrosion issues) and properly terminated with marine-grade connectors — leave those wire nuts and electrical tape joints at home! Finally, while it's fine to go with oversized wire, don't upsize the fuse. The BoatUS Marine Insurance claim files include many fire claims caused by centrifu-gal bilge pumps that overheated when something got caught in the rotor assembly and the fuse didn't blow because the installer thought a slightly bigger fuse would be better. When it comes to fuse size, follow the manufacturer's recommendations exactly.
What Maintenance Should I Be Doing? Problems with centrifugal pumps typically involve clogging, defective automatic float switches (if in-stalled), or corroded electrical connections, a common problem with any electrical gear installed in corro-sive environment of a vessel's bilge. Maintenance is generally limited to clearing the strainer (centrifugal pumps have one built into the base) and waterproofing all connectors. When it comes to repair, with the exception of the larger, rebuildable units, most centrifugal pumps are so inexpensive that it usually costs less to replace a damaged pump than repair it.
Maintenance and repair of diaphragm pumps typically involve opening up the pump body, clearing the pump chamber of debris, and checking the diaphragm and valves for damage or deterioration. Other than clogging, most problems will be caused by torn or damaged check valves. The diaphragms can also fail though they will typically outlast several valve changes. Pump disassembly for maintenance is nor-mally straightforward; however, some are more complex than others (multi-chambered units, for exam-ple), so be sure to read all instructions carefully to avoid common mistakes, such as improper orientation of check valves during installation.
So give that bilge pump a little respect, and it will keep your bilge dry and maybe even keep your boat afloat long enough for you to figure out where that water's coming from!
Source: http://www.boatus.com/seaworthy/magazine/2015/january/bilge-pump-basics.asp
Page 25 Volume I, Issue 6
Have you ever planned a great day of boating, only to discover that you left your sunglasses, sun block, or boat keys
at home? Try this solution.
Anchored in Biscayne Bay, 15 miles south of Miami, we'd just returned from a long dinghy ride and were looking forward to a cool drink. Suddenly, I realized we had locked the compan-ionway hatch and all the hatches in case of rain, and there was no way to get below. But no worries — I had my ditty bag with me.
In the 17th century, British sailors kept their personal items in what they used to call a “housewife," a tubular-shaped fabric sack closed with a draw-string that contained their belongings as well as essentials for repairing clothing and some tools of the trade. These bags, companions to the sailors' sea bags or sea chests, were hung from a hammock ring or a hook or peg next to their bunks. Eventually, they became known as ditty bags, and they're still a great way to keep things close at hand. Whenever we go to our boat, the beach, or just on a picnic, my ditty bag goes with me and contains everything I might not even know I need. My ditty bag is about 6 inches by 12 inches with a zipper from end to end. Made from heavy material, it has carrying handles on the top and end. In-side are pockets and a plastic sleeve to hold papers. Outside is a zipper pocket to hold keys or money. The modern design is more like a duffle bag and is easier to access via that long zipper. A small backpack will also fit the bill, as long as it's reserved just for this purpose.
During the 40-plus years that my wife and I lived aboard our houseboat, powerboats, and sailboats big and small, I've carried a ditty bag pretty much every time I leave the boat, and it's saved my bacon many times. Inside mine is:
A Ditty Bag For Modern Boaters
Flashlight
Leatherman multitool
Magnet on a string to retrieve metal objects that fall overboard or into crevasses
Cell-phone charger
Earbuds
Camera (though now those are
on our smartphones)
Sun block
Tape measure
Waterproof sportwatch
Ballpoint pen
Index cards
Fishing license
Reading glasses
Sunglasses
Toothpicks
Band-Aids
Chewing gum
Seasick pills
BoatUS membership card
Extra keys
If you're going out exploring long distances in your dinghy, add:
Handheld VHF
Personal locator beacon Carry anything you don't want to get wet inside re-sealable bags. Luckily, when we were locked out of our boat, we could open the companionway because I'd hidden an extra key, attached with a screw beneath an outside hatch. In my handy ditty bag was a screwdriver, and in minutes we were below enjoying those cold drinks. Source: http://www.boatus.com/magazine/2015/october/a-ditty-bag-for-modern-boaters.asp?utm_source=BMAG&utm_medium=email&utm_campaign=bmag_art4_915
Page 26 The Scuttlebutt
DATE CLUB Hours Loca on Ticket Price
10/10/2015 Red Eye Yacht Club 7 p.m. ‐ 11 Mar n's East $90, $45 Princess
10/16/2015 O er Point YC 7 p.m ‐ 12 O er Point $75, $35 Princess
10/17/2015 Bal more Yacht Club Bal more Yacht Club $85, $45 Princess
10/24/2015 Wellwood YC & MD Cruising 7 p.m. ‐ 11 Minker Hall $75, $40 Princess
11/7/2015 Miles River Yacht Club Miles River Y.C.
11/7/2015 Riverside Yacht Club of MD 7 ‐ midnight Mar n's East $90, $50 Princesses
11/8/2015 Neptune Yacht Club 8 p.m. ‐ 1 a.m. Mar n's West $85, $45 for Princesses
11/21/2015 Maryland Yacht Club 6:30 ‐ Midnight Maryland Y.C. $80, $45 Princesses
12/5/2015 Eastern Yacht Club 6 ‐ 12:30 Eastern Y.C. $75 $50 Princess
Kent Island Yacht Club 6 to 11 Kent Island Y.C. $95, $40 Princesses
12/12/2015 CBYCA 6 to midnight Bal more Yacht Club
1/9/2016 Bush River Yacht Club 6 p.m. ‐ 12
Waters Edge Event Center, Belcamp,
MD $90, $45 Princess
1/16/2015 Chesapeake Commodores Club 6 ‐ 1 a.m. Princess Royale $450 for the Weekend
1/30/2016 Galloway Yacht Club 5 p.m. ‐ 11 Boumi Shriners $90, $50
2/6/2016 Middle River Yacht Club 7 p.m.‐12 Richlin Ballroom $95, $45 Princesses
2/13/2016 Bodkin Yacht Club 6 to midnight Turf Valley $95, $45 Princesses
2/20/2016 Crescent Yacht Club 6:30 ‐ 12 Sherton Towson $85, $45 Princess
3/5/2016 Marley Boat Club Reflec ons Banquet
Hall
Ball Schedule
Page 27 Volume I, Issue 6
CLUB Contact Phone Email
Red Eye Yacht Club Stephanie Gaff 443‐682‐1541 familygaff@yahoo.com
O er Point YC Cathy Himpler 410‐598‐8108 bhimpler@verizon.net
Bal more Yacht Club Rick Burns 443‐570‐2231 rsvpbycball@gmail.com
Wellwood YC & MD Cruising Cheryl Blakey 610‐620‐5513 cblakey3@gmail.com
Miles River Yacht Club Margo Smith 410‐745‐9511
Riverside Yacht Club of MD Vernon McCarthy 717‐227‐9082 seaspray2@comcast.net
Neptune Yacht Club Pam Butler 410‐627‐5264 pamlbutler@verizon.net
Maryland Yacht Club Carole Suser 410‐255‐4444 manager@mdyc.org
Eastern Yacht Club Sharon Winterling 410‐299‐7933 sharonwinterling@gmail.com
Kent Island Yacht Club 410‐643‐4101 kiyc@kiyc.org
CBYCA Janet Yodris 410‐979‐9699 jyodris8434@comcast.net
Bush River Yacht Club Deb Noon debsom917@gmail.com
Chesapeake Commodores Club E/O Clint McLamb 410‐299‐2242 nflravens@gmail.com
Galloway Yacht Club Barb Polek 443‐992‐3776 barb@polek.org
Middle River Yacht Club Mary Philips mphilip9@jhmi.edu
Bodkin Yacht Club Pam Chaney 410‐245‐0691 pamela.chaney@gmail.com
Crescent Yacht Club Andy Socha 410‐882‐0541
Marley Boat Club Kellie Tysor 410‐218‐3215 kctysor@verizon.net
Ball Contacts
The Scuttlebutt MRYC Newsletter
Page 28 Volume I, Issue 6
Sun Mon Tue Wed Thu Fri Sat
1 Galloway Mee ng 7:00
2 3 Hurricane Weekend Work Party in the morning
4 Hurricane Weekend
5 6 7 8 Annapolis SailBoat Show
9 Boat Show
10 Day on the Bay Rock Hall REYC Ball Boat Show
11 Boat Show
12 Board Mee ng 8:00
13 14 15 Annapolis Power‐Boat Show
16 MRYC Mee ng 8:00 Nomina ons OPYC Ball Boat Show
17 BYC Ball Boat Show
18 Boat Show
19 20 21 22 23 Bingo 7pm NPYC
24 Wellwood Ball MD Cruising Ball Halloween Party MRYC EYC Frostbite Cruise to MRYC 6:00
25 26 27 28 29 30 31 Halloween Party Chesapeake City
October 2015
Page 29 Volume I, Issue 6
Sun Mon Tue Wed Thu Fri Sat
1 2 3 4 5 Galloway Mee ng 7:00
6 7 Miles River Ball Riverside YC Ball
8 Neptune YC Ball Princess Cere‐mony MRYC
9 10 11 12 13 14
15 16 Board Mee ng 8:00
17 18 19 20 MRYC Mee ng 8:00 Elec ons
21 Maryland YC Ball
22 23 24 25 26 Thanksgiving
27 28
29 30 31
November 2015
Page 30 The Scuttlebutt
Lee and Joyce Adams Pat Adams Janet Adey Jerry Caldwell George and Norma Culbertson Bill and Pat Blondell Russell Dantine Vern Davies Jack Deckelman Jean Emery George and Edith Forker Tillie Foy Rob Bob Gilman Gary Greenfield Carol Harden Ed and Irene Kligenstein John and Mary Lamont Josie Parks George Peck Mary Philip Jean Ryan Marion Sawyer Pat Smith John Sweet
Honorary Members
PC Roman Szyjka PC Kent and Sylvia Terry PC Gordon Vipperman PC Jeff Rigatti PC Lloyd Moore PC Sharon Garloff PC Eddie and Debbie Hernandez
Page 31 Volume I, Issue 6
1938-61 Captain “Buck” Regester* 1962 John Bender * 1963 Ray Huber* 1964 Ottis Chester* 1965 Paul Wunder 1966 Ed Klingenstein 1967 Paul Wunder 1968 Ed Klingenstein, 1969 John Boumer 1970 John Sweet, Jr. 1971 John Sweet, Jr. 1972 Bud Robb 1973 Harry Burkhardt * 1974 Harry Burkhardt 1975 Ben Markley, Sr. * 1976 Bob Bowersox * 1977 Matt Sithowski * 1978 Herbert Garber* 1979 Herbert Garber* 1980 Ray Adey 1981 Ray Adey 1982 Dave Edkels* 1983 John Sweet 1984 Francis Capp* 1985 Bo Bodenshatz 1986 Bo Bodenshatz 1987 Harry Foy* 1988 Dorothy Capp * Deceased
Past Commodores
1989 Ray Adey 1990 Herbert Garber* 1991 Danny Miller 1992 Bo Bodenshatz 1993 1994 1995 Joe Gaydos* 1996 Roman Szyjka 1997 Gus Philip 1998 Pat Adams 1999 Lloyd Moore 2000 Lloyd Moore 2001 Ed Hernandez 2002 Bill Adey* 2003 Jeff Rigatti 2004 Bruce Bickel 2005 Sharon Garloff 2006 Jim Smith* 2007 Gordon Vipperman 2008 Bill Bennett 2009 Larry Vinck 2010 Terry Birmingham 2011 Jack Lewis 2012 Kent Terry 2013 Carl Kurgan 2014 Joe Vislocky
200 Nantikote Drive Essex, Maryland, 21221
Phone: 410-687-1160
info@middleriveryachtclub.com
We’re on the Web! middleriveryachtclub.com
www.facebook.com/MiddleRiverYachtClub
MIDDLE RIVER YACHT CLUB The Officers and
Board of Directors of the
Middle River Yacht Club wish you a fun and fantastic
boating season.
Page 32 The Scuttlebutt
top related