Transcript
© 2012 Underwriters Laboratories Inc. All rights reserved. For RDSO internal Distribution Only.
UL INDIA LABORATORY
Testing Capabilities
© 2011 Underwriters Laboratories Inc.
Photo Voltaic Laboratory
Key Features
� NABL Accredited Laboratory
� Calibrated Equipment
� Controlled Ambient
� Exhaustive UPS & DG Backup power
� Centralized & Overnight Test Monitoring system
� Remote Monitoring System (IP Camera)
� Safe Work Environment
� Qualified Staffs
� Lean Work Flow
� High Visibility
3
4
Lean Lab Layout
Applicable Standards
� UL 1703 - Flat plate photovoltaic modules
and panels
� IEC 61215 - Crystalline Silicon terrestrial
photovoltaic modules – Design and type
approval
� IEC 61646 - Thin film terrestrial photovoltaic
modules – Design and type approval
� IEC 61730-1 - Photovoltaic module safety
qualification – Requirement for construction
� IEC 61730-2 - Photovoltaic module safety
qualification – Requirement for testingAccreditation/Approvals/
Recognitions
List of Tests as per UL- 1703
o Leakage Current Test (As Rcvd)
o Dielectric Voltage Withstand Test(As Rcvd)
o Wet Insulation Resistance Test (As Rcvd)
o Wiring Compartment Securement Test (As Rcvd)
o Voltage and Current Measurement
o Temperature Cycling Test
o Water Spray Test (Leakage + DWV)
o Bonding Resistance Test
o Reverse Current Overload Test
o Humidity Cycling Test (Pre & Post Testing to be done)
o Strain Relief Test
7
List of Testing as per UL- 1703 (cont’d)
o Cut Test
o Push Test (Leakage)
o Impact Test
o Mechanical Loading Test
o Terminal Torque Test
o Knockout Test
o Bending Test
o Low Temperature Impact Test
o Crush Resistance Test
o Mold Stress Relief Distortion Test
o Hot-Spot Endurance Test
List of Testing – IEC 61215/61646
o Visual Inspection
o Maximum Power Determination
o Insulation Test
o Measurement of temperature Coefficients
o Measurement of NOCT
o Performance at STC and NOCT
o Performance at Low Irradiance
o Outdoor exposure Test
o Hot-spot Endurance Test
o UV Preconditioning
9
List of Testing – IEC 61215/61646 (cont’d)
o Thermal Cycling Test
o Humidity Freeze Test
o Damp Heat Test
o Robustness of termination Test
o Wet Leakage Current Test
o Mechanical Load test
o Hail Test
o Bypass Diode Thermal Test
o Light Soaking (61646)
Specifications :
Make:- Spire; Model:- 4600SLP; Class A
Simulator
Standards Used :
UL 1703; IEC 61215/61646; IEC 61730-1 ;
IEC 61730-2; MNRE; RDSO
Tests :
o Voltage and Current Measurement
o Maximum Power Determination
o Performance at Low Irradiance
o Measurement of temperature Coefficients
o Initial & Final measurements of PV modules
Products Testes :
o Crystalline PV modules
o Thin film PV modules
Test Duration : 20 mints
Samples Required : 1
Solar Sun Simulator
Surge Voltage and Partial Discharge
Specifications :
Make: EM Test Equipment’s
Voltage range: 10 KV
Standards Used :
IEC 61730-1 ; IEC 61730-2;
Tests :
o Surge voltage
Products Tested : (Few examples)
o PV modules
Specifications :
Make: MPS Test Equipment’s
Voltage range: 10 KV DC
Standards Used :
IEC 61730-1 ; IEC 61730-2;
Tests :
Partial Discharge
Products Tested : (Few examples)
o PV modules( Back Sheet)
Specifications :
Make: Ascott
Internal size: 1 x 1.8 mtr
Temperature: 50 deg C & 95% RH
Standards Used :
MNRE; RDSO: ASTM 117
Tests :
o Corrosion Testing
Products Tested :
o PV modules and Outdoor exposed
products
Test Duration : 96 hrs and depends
upon customer requirement
Samples Required : 1
Salt Spray Chamber
Walking Chambers – Normal Size
Specifications :
Make:- ESPEC;
Temp. range:- -650C to 1500C
Humidity range:- 35% to 95% RH
Internal Size (mtrs):- 2.32(W)x4.0(D)x2.88 (H)
Data recording though web controller
Standards Used :
UL 60601; UL60950; UL 61010; UL 1703;
IEC 61215/61646; IEC 61730-1 ; IEC 61730-2
Tests :
o Humidity conditioning
o Thermal cycling
o Thermal simulation
o Aging
o Performance at various T and RH
o Humidity freeze
Products Tested : (Few examples)
o PV modules; ITE; measuring & medical products
o Industrial Panels and control products PV modules
Test Duration : As per STD
Samples Required : As per STD/Customer protocol
Walk-In Chamber - Mega Size
Specifications :
Make:- ESPEC;
Temp. range:- -650C to 1500C
Humidity range:- 35% to 95% RH
Internal Size (mtrs):- 3.04(W)x3.65(D)x 2.38(H)
Data recording though web controller
Standards Used :
UL 60601; UL60950; UL 61010; UL 1703;
IEC 61215/61646; IEC 61730-1 ; IEC 61730-2
Tests :
o Humidity conditioning
o Thermal cycling
o Thermal simulation
o Aging
o Performance at various T and RH
o Humidity freeze Products Tested : (Few examples)
o PV modules; ITE; measuring & medical products
o Industrial Panels and control products PV modules
Test Duration : As per STD
Samples Required : As per STD/Customer protocol
Hot Spot Endurance
Specifications :
Make:- Custom made
Standards Used :
UL 1703
Tests :
o Hot spot endurance
Products Testes :
o Crystalline PV modules
o Thin film PV modules
Test Duration : 100 cycles; 1 hrs/cycle
Samples Required : 2
Module Breakage
Specifications :
Make:- Custom made
Standards Used :
UL 1703
Tests :
o Module breakage
Products Testes :
o Crystalline PV modules
o Thin film PV modules
Test Duration : 10 min
Samples Required : 1
Rain and Outdoor Testing
Rain Test Apparatus
Lab TAT
Sample Preparation:15min
Test Duration:1 Hour
No. of samples: 01
Dielectric Tester + Leakage
Current Tester
Lab TAT
Sample Preparation:15min
Test Duration :5min
No. of Samples:01
IV Curve Tracer (Outdoor Testing)
Lab TAT
Sample Preparation Depends
Test Duration on test
conditions
No. of Samples: 01
© 2011 Underwriters Laboratories Inc.
Hi-Tech & Lighting Laboratory
Lean Lab layout
19
Testing CategoriesHi-Tech
o Information Technology Equipment
o Consumer Electronics
o Medical Equipment
o Measuring Devices
Components
o Motors
o Low Voltage Transformers
o Capacitors
Luminaries
o Portable Luminaires,
o Fixed Luminaires
20
Information Technology Equipment's
Standards Covered:
o UL 60950-1 First and Second Edition
o IEC/EN 60950-1 First and Second Edition
o CAN/CSA-C22.2 No. 60950-1
General Products
o Power Supplies
o Desktop Computers
o Laptops
o IP Camera
o RF Repeater etc…
21
Accreditation/Approvals/Recognitions
Consumer Electronics
Standards Covered:
o UL 60065-7
o IEC/EN 60065-7
o CAN/CSA-C22.2 No. 60065
o IEC 62087
General Products
o Television
o Audio & Video Equipment's
o LED Displays
o Camera etc..
22
Accreditation/Approvals/Recognitions
Medical & Measuring Equipment's
Standards Covered:
o UL 60601-1 Second Edition
o IEC/EN 60601-1 Second Edition
o CAN/CSA-C22.2 No. 601-1
o IEC/UL 61010-1
o Particular Standards
General Products
o Patient Monitoring System
o Incubators & Baby Warmers
o ECG Machine
o Photo Therapy Unit
o Power Analyzer etc…
23
Accreditation/Approvals/Recognitions
Luminaries
Standards Covered:
o UL 153
o IEC/EN 60598-1
o IEC/EN 60598-2-4
o CAN/CSA-C22.2 No. 12
General Products
o Table Luminaires
o Floor Luminaires
o Wall Mounted Luminaires
o Ceiling / Pendant Luminaires etc..
24
Accreditation/Approvals/Recognitions
Components
Standards Covered:
� MOTORS
� UL 1004
� BIS Standards
� LOW VOLTAGE TRANSFORMERS
� UL 5085
� CAPACITORS
� UL 810
� IEC 60252-2
25
Accreditation/Approvals/Recognitions
Electrical Testing
o Hi Pot Test or Electric Strength Test:
� Voltage: 0 – 10KV AC & DC.
� Leakage Current: Up to 200 mA
� Duration: Up to 900 Sec
� Supply: 50 or 60 Hz
o Bonding Conductor Test:
� Voltage: Up to 6 VAC.
� Current: Up to 60 Ampere
� Duration: Up to 999 Sec
26
Electrical Testing(Cont’d)
o Temperature measurement
� Range: -200 to 400 Degree Celsius
� Thermocouple: J, T, K Type
� Centralized Data Logging System
� Elevated Temperature -70 to 150 Degree Celsius
o Leakage Current measurement
� Simpson 228, 229 (IEC-60990)
� 0-3 mA
� Various Medical Leakage measuring Networks
27
Hysteresis Dynamometer
28
Specifications :
Make:- Magtrol
HD 815 - 28 Nm - Upto 5 HP motor
HD 715 - 6.5 Nm - Upto 2 HP motor
HD 515 - 1.7 Nm - Upto 0.5 HP motor
Standards Used :
UL 1004; UL2111; IS 325; IS 996
Tests :
o Input rating
o Running temperature rise
o Running overload
o Pullout torque
o Full load torque characteristics
Products Tested : (Few examples)
o Impedance protected motors
o Thermal protected motors
o Universal motors
Test Duration : 20 mints
Samples Required : 1
Humidity Chamber – Small Size
29
Specifications :
Make:- ESPEC
Temp. range:- -700C to 1500C
Humidity range:- 20% to 98% RH
Internal Size :- 1 meter cube
Standards Used :
UL 60601; UL60950; UL 61010; EN
60598-1
Tests :
o Humidity conditioning
o Thermal cycling
o Thermal simulation, Aging
o Performance at various T and RH
Products Tested : (Few examples)
o Lighting, measuring & medical
o Industrial Panels control products
Test Duration : As per standard
Samples Required : As per standard
Hot Air Oven
30
Specifications :
Make:- Kaleidoscope
Temp. range:- Ambient to 1000C
Test space:- 1000x1000x1500mm (WxDxH)
Temp & RH Data recording
Standards Used :
UL 60601; UL60950; UL 61010; EN 60598-1
Tests :
o Thermal conditioning
o Thermal simulation, Aging
o Performance at various Temp
Products Tested : (Few examples)
o Lighting, measuring & medical products
o Industrial Panels control products
Test Duration : As per STD
Samples Required : As per STD/Customer
protocol
Specifications :
Make: C N Envirosystem
Model: Aerial-2000-1
Internal Size: 2000 X 1000 X 1100mm (WxDxH)
Standards Used :
IEC 60529
Tests :
o IP5X, IP6X to IP67
Products Testes :
o Luminaires
o Control Panels
o Appliances
o Industrial Products
Test Duration : As per standard
Samples Required : 1
Dust Chamber
Specifications :
Make: C N Envirosystem
Model: Aerial-3500-IXX
Internal Size: 1500 X 1500 X 1500mm (WxDxH)
Standards Used :
IEC 60529
Tests :
o IP4X, IP5X, IPX1 to IPX6
Products Testes :
o Luminaires
o Control Panels
o Appliances
o Industrial Products
Test Duration : As per standard
Samples Required : 1
Ingress Protection (Water) Chamber
Mechanical Test
o Accessibility Probes
� Various accessible probes as per IEC/UL
standards.
o Force Tester
� Up to 200 Kg
o Impact Hammer
� 0.2 J to 1 J
o Impact Ball
� Diameter:50 mm
� Weight: 500 G
33
o Steady Force Tester
� Up to 200Kg
o Draft Free Enclosure
� As per standard IEC 60598
34
Mechanical Test
© 2011 Underwriters Laboratories Inc.
Power & Control Laboratory
IS Standards Capabilities
� IS/IEC 60898(Pt-1):2002 - Circuit-breakers for over current protection for household and similar installations (MCB)
� IS 12640(Pt-1):2008 - Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs)
� IS 12640(Pt-2):2008 - Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs)
� IS/IEC 60947(Pt-4/Sec-1):2000 upto 315Amp -Contactors and Motor Starter
� IS/IEC 60947(Pt-5/Sec-1):2003 - Control Circuit Devices and Switching elements -Electromechanical control circuit devices
36
Accreditation/Approvals/Recognitions
IEC & UL Standards Information(Cont’d)
� UL 60947-1 3rd edition
� UL 60947-4-1A 2nd edition
� UL 60947-5-2 2nd edition
� UL 60947-5-1 3rd edition
� UL 61131-2 2nd edition
� UL 61800-5-1
� UL508
� UL 486A-486B
� UL1059
� UL467
� UL746 A & C
37
Accreditation/Approvals/Recognitions
10kA Short Circuit Facility
38
Specifications :
Control Station: Semica data systems & Sarman
Engineering
Standards Used :
UL 508; IEC 60898 ; 61008; 61009; 60947
Tests :
o All Short circuit test for IEC 60898; 61008;
61009.
o For other product category upto 10KA at
voltage upto 690V at any Power factor.
Test Duration : Depends upon the product
category.
Samples Required : As Per Standard.
28-Days & Temperature Rise Test Bench
39
Specifications :
Make:- SCR Electroniks.
Voltage range: Minimum 30VAC, 50 Hz
Current range: 0.5 to 125A continuous
Environmental Chamber: 25 to 40 deg C
Standards Used :
IEC 60898; 61008; 61009; 60947
Tests :
o Temperature rise
o 28 days test
o Over current
o Tripping test
Products Tested : (Few examples)
o MCB’s; RCCB’s; RCBO’s; Relays
RCCB & RCBO Residual Current Characteristics
Test Bench
40
Specifications :
Make:- SCR Electroniks
Voltage range: 0 to 300 VAC, 50 Hz
All test corresponding to sensitivity 10mA to
300 mA is possible, as per IEC 61008 & 61009.
Standards Used :
IEC61008; 61009
Tests :
o RCCB/RCBO type testing
Products Tested : (Few examples)
o RCCB’s; RCBO’s;
Tripping Characteristic Bench
41
Specifications :
Make:- SCR Electroniks.
Voltage range: 3 to 12 VAC, 50 Hz
Thermal current: 0.5A to 125A
Magnetic current: Upto 2000A (100 ms)
Standards Used :
IEC 60947; 60898; 61009;UL508
Tests :
o Tripping characteristics
o Calibration test
Products Tested : (Few examples)
o MCB’s; RCBO’s; Relays;
o MPCB’s
AC Pilot Duty Endurance
42
Specifications :
Make:- Sarman engineering
Voltage range: 25 to 660 VAC, 50 Hz
Make current: Upto 100A
Break current: Upto 10A
Duty cycle – As per standard
Standards Used :
IEC 60947-5-1
UL 508
Tests :
o Pilot duty endurance
o Normal endurance
Products Tested : (Few examples)
o Contactors; Overload relays; Auxiliary
devices
DC Pilot Duty Testing
43
Specifications :
Make:- Sarman Engineering.
Voltage range: 99 to 660 VDC,
Duty current: 0.1A to 7.5A
Duty cycle – As per standard
Standards Used :
IEC 60947-5-1
UL 508
Tests :
o Pilot duty endurance
o Normal endurance
Products Tested : (Few examples)
o Contactors; Overload relays; Auxiliary
devices
Impulse Generator
44
Specifications :
Make:- EMC Partner
Voltage range – 750 to 19.5 Kv
Peak – Positive/Negative
Standards Used :
IEC 60947; 60898; 61008; 61009; UL 508
Tests :
o Impulse voltage test
Products Tested : (Few examples)
o MCB’s; RCCB’s ; RCBO’s; Contactors
Test Duration : 45 mints
Samples Required : As Per Standard
Glow Wire Testing
45
Specifications :
Make:- SCR Electroniks.
Standards Used :
IEC 60898; 61008; 61009; 60947
Tests :
o Glow wire test
Products Testes :
o MCB; RCCB; RCBO; Contactor
Test Duration : 20 mints
Samples Required : As per standard
Low Voltage and High Current Source
46
Specifications :
Make: Sarman
Voltage range: 3 to 6 VAC, 50 Hz
Current range: 10 to 2000A continuous
2000A to 6000A (10 Secs)
Standards Used :
UL 508; 1059; 486A; 486B; 467;
IEC 60947; 60898; 61008; 61009
Tests :
o Temperature rise
o Heat cycling
o Short time current
o Over current
Products Tested : (Few examples)
o Contactors, Terminal connectors, Ground
rods, Lugs
MCB Endurance Testing
47
Specifications :
Make:- SCR Electroniks
Voltage range: 25 to 480 VAC, 50 Hz
Test current: 0.5 to 125A
Duty cycle – 2 :28, 2: 13
Standards Used :
IEC 60898; 61008; 61009
Tests :
o Endurance testing
Products Tested : (Few examples)
o MCB’s; RCCB’s; RCBO’s;
Overload Endurance Testing
48
Overload endurance test 3 phase rating configuration
Std ProductTest
Name as per Std
Volts (Min to Max)
Current A Power Factor
60947-1 General General Std
60947-4-1 Contactor/Staters
Up to 690 Volts,9 to 2500 A,0.45 to 0.98 PF, 60947-5-1 Auxiliary
UL508 General
Secureness Test Setup
49
Specifications :
Make:- CK Enterprises
Torque : 1 ~ 600 lbf.in
Stations : 4
Standards Used :
IEC 60947
UL 467; 508; 486A; 486B
Tests :
o Conductor secureness
o Static heating sequence
Products Tested : (Few examples)
o Terminals of contactor, overload relays,
terminal block
o Lugs & Ground clamps
Secureness Test Setup
50
Specifications :
Make:- CK Enterprises
Torque : 1 ~ 600 lbf.in
Stations : 4
Standards Used :
IEC 60947
UL 467; 508; 486A; 486B
Tests :
o Conductor secureness
o Static heating sequence
Products Tested : (Few Examples)
o Terminals of contactor, overload relays,
terminal block
o Lugs & Ground clamps
Pullout Testing
51
Specifications :
Make:- CK Enterprises
Torque : 10 ~ 1000 kgs
Standards Used :
IEC 60947
UL 467
Tests :
o Conductor abnormal pullout
o Static heating sequence
Products Tested : (Few examples)
o Terminals of contactor, overload relays,
terminal block
o Lugs & Ground clamps
Temperature Rise Testing - DC
o Range:
� Current : 5 to 1000A Continues,
1000 to 3000A (15 Sec).
� Voltage: 3 to 6Vac,50 Hz supply.
� Test: One sample
o Mode: Cyclic operation with single station
o TAT: 4 Hrs. including test setup,
Except cycling test
o Standards :
� IEC 60947-4-1,5-1,7-1,60898,61008,61009Series
� UL508 Series, UL1059,486 A & B,467,746 Etc…
52
Mechanical Shock Testing - MCB
o Range:
� Spring constant:25 N/mm
� Sample: 180 mm Axis from the platform
� Mounting: Surface 200mm from Hing.
� Static force: 25 Nm Fixed metal stop plate
� Fall: 50 times allow.
� Axis: 90 Deg vertical
o Caution: During the tests, the circuit-breaker
shall not open.
o TAT: 30 Min / Sample’s
o Standards :
� IEC 60898,61008,61009 Series
53
Adherence of Coating
o Sample Requirement:
� Copper jacketed ground rod
� Length : 457mm (18 in) length of
the rod with one end cut to a 45
Degree point.
o No of Samples: 1
o Standards :
� UL467
54
© 2012 Underwriters Laboratories Inc. All rights reserved. For RDSO internal Distribution Only.
UL , ManesarEnergy Efficiency Laboratory
Agenda
� Introduction
� Photometric Lab
� Environmental Lab
� Refrigerator Lab.
� Upcoming facilities
� Question and Answer
56
57
Principle:The mirror rotates around theluminaire and reflects all the lightintensity signal from every direction tothe fixed photo detector, thus toachieve the measurement of thespatial intensity distribution curve ondifferent flats. The instrument is fullysatisfied with the test requirements onthe directional properties of lightdistribution made by LM79-0, ESTand ERP meanwhile, it isrecommended by CIE70.
Photometry Lab (Goniophotometer )
58
Features:Computerized measurementsof following parameters
• Spectroradiometric• Colorimetric• Spectral power distribution,
Chromaticity coordinates,• CCT , CRI• Luminous flux,• Electrical ( Current, voltage,
wattage, power factor etc)
Photometry Lab (Thermostatic Integrating Spher )
59
Fully atomized life test racks for the LEDbulbs, CFL , TFL which are designed by UL.Individual lamp is monitor throughout its lifeduring testing in the life test and actual life oflamp is capture in case of failure. Themonitoring of life test area and reportgeneration is customized as per standardsneed. The racks operate under the controlledelectrical power supply (voltage, frequency)on UPS and controlled environmentalconditions specified in the standards.
Photometry Lab (Life Test Racks )
60
Computerized spectroradiometric and colorimetric parameters measurement like spectral powerdistribution, chromaticity coordinates, correlated color temperature, color rendering index, colortolerance, color difference of LED Chip at different junction temperature ( 15°C to 85°C)
Photometry Lab (Thermostatic Integrating Sphere for LED chip)
Environmental Lab ( Environmental chambers)
61
This Lab is having high performance Environmental test Chamberswith fully automatic control , dust chamber and rain test apparatusand Hot ovens. The products like luminaires , Lamps , Electrical /Electronic components , enclosures etc performance can beassessed under various environmental stresses like hightemperature , low temperature , dusty environment and rainyenvironment.The different sizes of environmental chambers accommodate test objects of different sizes and tests as per• Cold• Dry heat• Change of temp• Damp Heat, Steady State• Damp heat, steady state (unsaturated pressurized vapour) • Damp Heat, Cyclic • Damp Heat, Steady State
Temperature : (-)40 ⁰⁰⁰⁰C to 180 ⁰⁰⁰⁰C± 1⁰⁰⁰⁰C Relative Humidity : 10 % to 95%± 3 % Ramp rate
: 10 K per minute
62
Lab has largest dust chamber of size ( 3 m x 2 m x 3m ,l x d x h) and rain test apparatus to test enclosures fordegree of protection against dust and water. This facilitieswill help manufactures for design and verification of theirproducts for the IP rating in accordance withIEC:60529/IS:12063 . The electrical enclosures likeelectrical panel , control box , distribution box , motors ,etc can be tested for the protection against ingress ofdust ( 1st numeral 1X/2X/3X/4X/5X/6X) and water ( 2nd
Numeral: X3/X4/X5/X6).
Environmental Lab ( Dust Chamber and Rain Test set up)
63
This Lab is having test chamber as per ISO 15002with temperature environment control system and arefrigerator cooling performance test system The system isfully automatically controlled, capable of automaticmeasurement and recording and analysis of test results anddata. The system is intended for the operating conditions tests(temperature, humidity, ) suitable for 6 Refrigerators with size50l to 750l. The verification testing of house hold refrigeratorcan be performed for the energy efficiency requirement• As per BEE star rating scheme , • As per EPA Energy star scheme and various other nations
energy efficiency labeling system. • The system meets the conditions as per the national
standards IS 15750, IS: 1476, ASNZ 4474 , IEC: 62552:2007.
Refrigerator Lab ( Dust Chamber and Rain Test set up)
Feature:Six test benchesProgrammable controls - to suit R&D testing requirement.Hydro Carbon Refrigerant compatibility
Up coming facilities
Washing Machine Lab: The verification testing will be performed for the energyefficiency requirement as per BEE star rating scheme , EPA Energystar scheme and various other nations energy efficiency labelingsystem. The system meets the conditions as per the nationalstandards IEC 60456
Performance Tests:a. Energy and Water consumptionb. Determination of Wash Performancec. Water Extraction Efficiencyd. Rinsing efficiency
64
Up coming facilites
Consumer Electronic Appliance Lab: This Lab will be commission by
March 2012. The verification testing will be performed for the energy efficiency requirement as per BEE star rating scheme , EPA Energy star scheme and various other nations energy efficiency labeling system.
Performance Tests: a. Televisionb. Computer and Serverc. Printersd. Audio , video appliance
65
© 2011 Underwriters Laboratories Inc.
Water Laboratory
Specifications :
Make:- Olympus; Model:- BX 53
Tests :
o For counting protozoan oocyst( using FITC
and DAPI stain)
o For counting Microspheres
Products Tested :
o Water samples
Fluorescent Microscope
Specifications :
Make:- HACH; Model:- DR/5000
Tests :
o Free chlorine and other halogens
o Metals-Iron, Manganese etc
o Halides
Products Tested :
o Water samples
Test Duration : 1 hour
Samples Required : Each test 100ml
Spectrophotometer
Specifications :
Make:- Perkin Elmer; Model:- AA800 with
GFAS,FAS and FIAS
Tests :
o Metals
Products Testes :
o Water samples
Samples Required : 200ml
AAS-Graphite furnace/FIAS
Specifications :
Make:- Shimadzu; Model:- TOCVCPH;
Tests :
o Total organic carbon estimation
o Inorganic carbon
o Total carbon
Products Testes :
o Water sample
Samples Required : 100ml
TOC analyzer
Specifications :
Make:- Agilent Technologies; Model:-GC-
7890A , MS-5975C with auto sampler and Purge
& Trap
Tests :
o Volatile organics
o Semi volatile organic compounds
o Organo Pesticides
Products Tested :
o Water samples
o Water treatment chemicals
o Water treatment components
GCMS
New Service Offerings
72
Renting & Leasing
• Conditioning Ovens • IP & Salt spray• Short circuit
New Testing Services
• NABL BIS MNRE• BEE EPA CEC• TEC CBTL
Surveillance Testing
• BIS • BEE• UL FUS
Research & Development Testing
• Hi-Tech & Medical • Industrial• Flammability
Customer Training
• Standard related • Testing exposure• Safety
Lab Setup Consultancy Services
• Design• Conversion• Project management
Mobile Testing Services
• Microbiology• Calibration• Medical
Consultancy & Audits
• Customized audits• 17025• Lean
Annual Contact Services
• Microbiology• Annual Inspection
Contact Details
K S Patil Engineering Manager, Power & Control/EnergyDirect : 91-80-41384436Mobile : +91 9980519308Email : Krushnendra.s.patil@ul.com
Jomy JosephBusiness Head, Power & Control/LightingDirect : 91-80-41384608Mobile : +91 9741399064Email : Jomy.Joseph@ul.com
73
THANK YOU.
top related