Tube Fusion-II TF200-II TF300-II TF320-II TF700-IIpdf.textfiles.com/manuals/STARINMANUALS/Hohner - Laney/TF200-II... · Tube Fusion-II TF200-II TF300-II TF320-II TF700-II. Laney OPERATING
Post on 11-Apr-2018
263 Views
Preview:
Transcript
Tub
eFu
sion
IIO
PER
AT
ING
INST
RU
CT
ION
S-
Issu
e1.1
Tube Fusion-IITF200-IITF300-IITF320-IITF700-II
Laney OPERATING INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using electric products, basic cautions should always be followed, including the following.
1. Read all safety and operating instructions before using this product2. All safety and operating instructions should be retained for future reference3. Obey all cautions in the Operating instructions and on the back of the unit4. All operating instructions should be followed5. This product should not be used near water, i.e. a bathtub, sink, swimming pool, wet basement, etc.6. This product should be located so that its position does not interfere with its proper ventilation. It should not
be placed flat against a wall or placed in a built up enclosure that will impede the flow of cooling air.7. This product should not be placed near a source of heat such as stove, radiator, or another heat producing
amplifier.8. Connect only to a power supply of the type marker on the unit adjacent to the power supply cord.9. Never break off the ground pin on a power supply cord.10. Power supply cords should always be handled carefully. Never walk or place equipment on power supply
cords. Periodically check cords for cuts or signs of stress, especially at the plug and the point where thechord exits the unit.
11. The power supply cord should be unplugged when the unit is to be unused for long periods of time.12. If this product is to be mounted in an equipment rack, rear support should be provided.13. The user should allow easy access to any mains plug, mains coupler and mains switch used in conjunction
with this unit thus making it readily operable.14. Metal parts can be cleaned with a damp cloth. The vinyl covering used on some units can be cleaned with
a damp cloth or ammonia based household cleaner if necessary. Disconnect the unit from the powersupply before cleaning.
15. Care should be taken so that objects do not fall and liquids are not spilled into the unit through anyventilation holes or openings. On no account place drinks on the unit.
16. A qualified service technician should check the unit if:The power cord has been damagedAnything has fallen or spilled into the unitThe unit does not appear to operate correctlyThe unit has been dropped or the enclosure damaged.
17. The user should not attempt to service the equipment. All service work is done by a qualifiedservice technician.
18. Exposure to extremely high noise levels may cause a permanent hearing gloss. Individuals varyconsiderably in susceptibility to noise induced hearing loss, but nearly everyone will lose some hearing ifexposed to sufficiently intense noise for a sufficient time. The U.S. Government's Occupational Safety andHealth Administration (OSHA) has specified the following permissible noise level exposure.
Duration Per Day In Hours Sound Level dBA, slow response
According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Ear
plugs or protectors in the ear canals or over the ears must be worn when operating this amplification system in
order to prevent a permanent hearing loss if exposure exceeds the limits set forth above. To ensure against
potentially dangerous exposure to high sound pressure levels it is recommended that all persons exposed to
equipment capable of producing high sound pressure levels such as this amplification system be protected by
hearing protectors while this unit is in operation.
SAVE THESE INSTRUCTIONS
12
12
14
8
6
4
3
2
1
1
or less
90
92
95
97
100
102
105
110
115
Dieses Symbol soll den Anwender vor unsolierten gefahrlichen Spannungen innerhalb des Gehauses warnen,die von Ausreichender Starke sind, um einen elektrischen Schlag verursachen zu konnen.
Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitungaufmerksam machen, die Handhabung und Wartung des Produkts betreffen.
Um einen elektrischen Schlag oder Feuergefahr zu vermeiden, sollte dieses Gerat nicht dem Regen oderFeuchtigkeit ausgesetzt werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.
Risiko - Elektrischer Schlag! Nicht offen!
Um das Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es befindensich keine Teile darin, die vom Anwender repariert werden Konnten. Reparaturen nur von qualifiziertemFachpersonal durchfuhren lassen
ACHTUNG
VORSICHT:
VORSICHT:
A
!
Este simbolo tiene el proposito de alertar al usuario de la presencia de (voltaje) peligroso que no tieneaislamiento dentro de la caja del producto que puede tener una magnitud suficiente como para constituir riesgode corrientazo
Este simbolo tiene el proposito de alertar al usario de la presencis de instrucconesimportantes sobre la operacion y mantenimiento en la literatura que viene con el producto
Para evitar corrientazos o peligro de incendio, no deja expuesto a la lluvia o humedad este aparato Antes deusar este aparato, lea mas advertcias en la guia de operacion
Riesgo de corrientazo - no abra
Para disminuir el riesgo de carrientazo, no abra la cubierta. No hay piezas adentro que el puedareparar. Deje todo mantenimiento a los tecnicos calificadod
ADVERTENCIA:
PRECAUCION:
PRECAUCION:
A
!
Ce symbole est utilise pur indiquer a l utilisateur de ce produit de tension non-isolee dangereuse pouvant etred intensite suffisante pour constituer un risque de choc electrique.
Ce symbole est utilise pour indiquer a l utilisanter qu il ou qu elle trouvera d importantes instrucions surl utilisation et l entrerien (service) de l appareil dans la litterature accompagnant le produit
Afin de prevenir les risques de decharge electrique ou de feu, n exposez pas cet appareil a la pluie oua l humidite. Avant d utiliser cet appareil, lisez les avertissements supplentaires situes dans le guide.
Risques de choc electrique - NE PAS OUVIRIR
Afin de reduire le risque de choc electrique, ne pas enlever le couvercle. Il ne se trouve a l interieuraucune piece pouvant etre reparee par l utilisateur. Confier l entretien a un personnel qualifie.
AVERTISSEMENT:
ATTENTION:
ATTENTION:
A
!
Intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure thatmay be of sufficient to constitute a risk of electrical shock to persons
Intended to alert the user of the presence of important operating and maintainance (servicing)instructions in the literature accompanying the product
To prevent electrical shock or fire hazard, do not expose this appliance to rain or moisture. Before using thisappliance please read the operating instructions for further warnings
Risk of electrical shock - DO NOT OPEN
To reduce the risk of electircal shock, do not remove the cover. No user servicable parts inside. Referservicing to qualified service personnel.
WARNING:
CAUTION:
CAUTION:
A
!
Laney OPERATING INSTRUCTIONS
Laney OPERATING INSTRUCTIONS
Care of your Laney amplifier will prolong it's life.....and yours!.
After unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug. Beforeplugging into the power supply ensure you are connecting to a grounded earth outlet.
If you should wish to change the factory fitted plug yourself, ensure that the wiring convention applicable to thecountry where the amplifier is to be used is strictly conformed to. As an example in the United Kingdom thecable colour code for connections are as follows.
EARTH OR GROUND - GREEN/YELLOWNEUTRAL - BLUELIVE - BROWN
Congratulations on your decision to purchase a LaneyTube Fusion amplifier.
Laney products are designed with ease of operation as a primary objective, however to ensure you derive thebest from your new amplifier, it is important you take time to read this user manual and to familiarise yourselfwith the control functions and facilities available.
INTRODUCTION
This manual has been written for easy access of information. The front and rear panels of each unit are graphicallyillustrated, with each control and feature numbered. For a description of the function of each control feature,simply check the number with the explanations adjacent to each panel.
Your Laney amplifier has undergone a thorough two stage,pre-delivery inspection,involving actual play testing,aswell as burn in.
When you first receive your LaneyTube Fusioin amp,follow these simple procedures:
(i) Ensure that the amplifier is set at the correct voltage for the country it is to be used in.
(Ii) Connect your instrument with a high quality shielded instrument cable. Use of cheap cables will compromisethe sound of your instrument and your amplifier.
BEFORE SWITCHING ON
Eng
Page 2
Eng
Laney
2
172 3 4 6 7 8 9 10 11 12 13 14
19 20 21
1
3
9
1
5
11
15
Tub
eFu
sion
-II
Page 3
OPERATING INSTRUCTIONS
15 1816
INPUT
VOLUME:
BRIGHT SWITCH:
BASS:
MIDDLE:
TREBLE:
SCOOP - Drive 1:
GAIN:
VOLUME:
SCOOP- Drive 2:
GAIN:
VOLUME:
BASS:
MIDDLE:
TREBLE:
: This socket should be used for connecting the instrument to the amplifier.
Adjusts the overall volume of the clean channel.
Adds brightness and sparkle to the upper frequencies of the clean channel.
Controls the clean channel low-frequency-EQ in the pre-amplifier.
Controls the clean channel mid-frequency-EQ in the pre-amplifier.
Controls the clean channel high-frequency-EQ in the pre-amplifier.
The scoop control radically cuts the level of mid range frequencies present in the
sound giving you a very modern, aggressive lead tone.
Sets the level of gain on the drive channel 1. For optimum results the gain control should be
used in conjunction with the volume control (9). Setting low levels of gain with high levels of volume will
result in a nice crisp bluesy lead tone. Setting the gain control to midway with a medium volume level will
give you a punchy hard rock lead tone and setting the gain to maximum and backing the volume off, gives
you a full on metal lead tone. Obviously the type of guitar you use will have an effect on the overall sound
you hear, but the above settings are meant as an indication of the different sounds that can be achieved.
Adjusts the overall volume of the drive channel 1.
The scoop control radically cuts the level of mid range frequencies present in the
sound giving you a very modern, aggressive lead tone.
Sets the level of gain on the drive channel 2. For optimum results the gain control should be
used in conjunction with the volume control (12). Setting low levels of gain with high levels of volume will
result in a nice crisp bluesy lead tone. Setting the gain control to midway with a medium volume level will
give you a punchy hard rock lead tone and setting the gain to maximum and backing the volume off, gives
you a full on metal lead tone. Obviously the type of guitar you use will have an effect on the overall sound
you hear, but the above settings are meant as an indication of the different sounds that can be achieved.
Adjusts the overall listening volume of the drive channel 2.
Shared Bass EQ control for drive channels 1 & 2, sets low end frequency response.
Shared MIDs EQ control for drive channels 1 & 2, sets Mid frequency response.
Shared Treble EQ control for drive channels 1 & 2, sets high end frequency response.
5
6
8
4
7
10
12
13
14
TF200-II Front Panel
7 7 7 7 7 77 7 7 7 7 7 7
1 1 1 1 1 11 1 1 1 1 1 19 9 9 9 9 99 9 9 9 9 9 9
3 3 3 3 3 33 3 3 3 3 3 3
10 10 10 10 10 1010 10 10 10 10 10 10
4 4 4 4 4 44 4 4 4 4 4 46 6 6 6 6 66 6 6 6 6 6 6
0 0 0 0 0 00 0 0 0 0 0 0
5 5 5 5 5 55 5 5 5 5 5 5
8 8 8 8 8 88 8 8 8 8 8 82 2 2 2 2 22 2 2 2 2 2 2
1
POWER
0
INPUT BASSCLEAN TREBLE GAIN GAINDRIVE1 DRIVE2
SCOOPBRIGHT SCOOP
VOLUME VOLUME BASS MIDDLE TREBLECLEAN
REVERBDRIVE
REVERBVIBEMIDDLEVOLUME
CLEAN CHANNEL DRIVE 1 DRIVE 2 DRIVE EQ REVERB
TUBE FUSION
7 7 7 7 7 77 7 7 7 7 7 7
1 1 1 1 1 11 1 1 1 1 1 19 9 9 9 9 99 9 9 9 9 9 9
3 3 3 3 3 33 3 3 3 3 3 3
10 10 10 10 10 1010 10 10 10 10 10 10
4 4 4 4 4 44 4 4 4 4 4 46 6 6 6 6 66 6 6 6 6 6 6
0 0 0 0 0 00 0 0 0 0 0 0
5 5 5 5 5 55 5 5 5 5 5 5
8 8 8 8 8 88 8 8 8 8 8 82 2 2 2 2 22 2 2 2 2 2 2
1
POWER
0
INPUT BASSCLEAN TREBLE GAIN GAINDRIVE1 DRIVE2
SCOOPBRIGHT SCOOP
VOLUME VOLUME BASS MIDDLE TREBLECLEAN
REVERBDRIVE
REVERBVIBEMIDDLEVOLUME
CLEAN CHANNEL DRIVE 1 DRIVE 2 DRIVE EQ REVERB
TUBE FUSION
22 POWER:
HEADPHONES:
EXTENSION SPEAKER SOCKET
FX RETURN :
FX SEND :
Socket for connecting external power source.
Socket provided for connecting pair of quality headphones. When headphones are connected tothe amplifier the output from the on board speaker is muted.
Socket provided for connecting the output of an external effects device.
Socket provided for connecting an external effects device. The output from this socket should beconnected to the external effect devices input.
FOOTSWITCH SOCKET:
:
Socket provided for connecting the supplied TF footswitch. The TF footswitch is adedicated footswitch forTF amplifiers please do not attempt to connect anything other than theTF footswitch suppliedas this may result in serious damage to your amplifier.
Socket provided for connecting an external speaker enclosure. NOTE Theminimum impedance of any speaker cabinet connected to you amplifier must not be less than 8 Ohms. Connecting aload of less than 8 Ohms will result in your amplifier overheating. Whilst this is not a problem in the short term,prolonged use in this manner will result in permanent damage to your amplifier and voiding of your amplifiers guarantee.
16
Eng
Laney OPERATING INSTRUCTIONSTu
be
Fusi
on
-II
172 3 4 6 7 8 9 10 11 12 13 14
24 25 27
1 5 15
23
16
23
24
27
17
Designed in the UK by BLT Industries LTD.
N1646N1646
MAXIMUM POWER CONSUMPTION
120 WATTS ~50/60 HZ
WARNING - THIS EQUIPMENT MUST BE EARTHED.
WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCKDO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOTREMOVE COVERS.NO USER SERVICEABLE PARTS INSIDE. REFERSERVICING TO QUALIFIED PERSONNEL ONLY.
ATTENTION - REMPLACER LE FUSIBLE SEULEMENT PAR LE MEMETYPE ET LE MEME CALIBRE.
ATTENTION - DEBRANCHER LE CORDON D ALIMENTATIONAVANT TOUTE INTERVENTION.
,AVIS - RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR.
CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIREREPLACE ONLY WITH SAME TYPE AND RATED FUSE.
T2A L 115V
T1A L 230V
~
~
T2A L 115V
T1A L 230V
~
~
FUSE RATING & SUPPLY VOLTAGE.
!CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
Serial Number
FX Return FX SendHead Phones
ExtensionLoudspeaker
8 OHMMINIMUM IMPEDANCE
FootswitchUse With Dedicated
TF3 Way Footswitch only.LaneyMADE IN CHINA
19 20 21
26
18
22
VIBE:
CLEAN REVERB LEVEL:
DRIVE REVERB LEVEL:
CLEAN CHANNEL SWITCH:
DRIVE 1 CHANNEL SWITCH:
DRIVE 2 CHANNEL SWITCH:
Generates a radical EQ cut and boost. Difficult to explain but easy to hear! Give it a try. Works on both
channels.
Sets the overall level of REVERB present in the clean channel signal.
Sets the overall level of REVERB present in the drive channel signal.
Selects the amplifiers CLEAN channel.
Selects the amplifiers DRIVE 1 channel.
Selects the amplifiers DRIVE 2 channel.
18
19
20
21
25
26
TF200-II Rear Panel
TF200-II Front Panel
Page 4
Eng
Laney OPERATING INSTRUCTIONSTu
be
Fusi
on
-II
172 3 4 6 7 8 9 10 11 12 13 14
19 20 21
1 5
Page 5
15 1816
INPUT
VOLUME:
BRIGHT SWITCH:
BASS:
MIDDLE:
TREBLE:
SCOOP - Drive 1:
GAIN:
VOLUME:
SCOOP- Drive 2:
GAIN:
VOLUME:
BASS:
MIDDLE:
TREBLE:
: This socket should be used for connecting the instrument to the amplifier.
Adjusts the overall volume of the clean channel.
Adds brightness and sparkle to the upper frequencies of the clean channel.
Controls the clean channel low-frequency-EQ in the pre-amplifier.
Controls the clean channel mid-frequency-EQ in the pre-amplifier.
Controls the clean channel high-frequency-EQ in the pre-amplifier.
The scoop control radically cuts the level of mid range frequencies present in the
sound giving you a very modern, aggressive lead tone.
Sets the level of gain on the drive channel 1. For optimum results the gain control should be
used in conjunction with the volume control (9). Setting low levels of gain with high levels of volume will
result in a nice crisp bluesy lead tone. Setting the gain control to midway with a medium volume level will
give you a punchy hard rock lead tone and setting the gain to maximum and backing the volume off, gives
you a full on metal lead tone. Obviously the type of guitar you use will have an effect on the overall sound
you hear, but the above settings are meant as an indication of the different sounds that can be achieved.
Adjusts the overall volume of the drive channel 1.
The scoop control radically cuts the level of mid range frequencies present in the
sound giving you a very modern, aggressive lead tone.
Sets the level of gain on the drive channel 2. For optimum results the gain control should be
used in conjunction with the volume control (12). Setting low levels of gain with high levels of volume will
result in a nice crisp bluesy lead tone. Setting the gain control to midway with a medium volume level will
give you a punchy hard rock lead tone and setting the gain to maximum and backing the volume off, gives
you a full on metal lead tone. Obviously the type of guitar you use will have an effect on the overall sound
you hear, but the above settings are meant as an indication of the different sounds that can be achieved.
Adjusts the overall listening volume of the drive channel 2.
Shared Bass EQ control for drive channels 1 & 2, sets low end frequency response.
Shared MIDs EQ control for drive channels 1 & 2, sets Mid frequency response.
Shared Treble EQ control for drive channels 1 & 2, sets high end frequency response.
TF300-II/ TF700-II* Front PanelTF320-II/
*TF700 - features identical pre amp to TF300
apart from being reversed
2
3
9
1
11
15
5
6
8
4
7
10
12
13
14
7 7 7 7 7 77 7 7 7 7
1 1 1 1 1 11 1 1 1 19 9 9 9 9 99 9 9 9 9
3 3 3 3 3 33 3 3 3 3
10 10 10 10 10 1010 10 10 10 10
4 4 4 4 4 44 4 4 4 46 6 6 6 6 66 6 6 6 6
0 0 0 0 0 00 0 0 0 0
5 5 5 5 5 55 5 5 5 5
8 8 8 8 8 88 8 8 8 82 2 2 2 2 22 2 2 2 2
1
POWER
0
INPUT BASSCLEAN TREBLE GAIN GAINDRIVE1 DRIVE2
SCOOPBRIGHT SCOOP
VOLUME VOLUME BASS MIDDLE TREBLE VIBECLEAN
REVERBDRIVE
REVERBMIDDLEVOLUME
7 7
1 19 9
3 3
10 10
4 46 6
0 0
5 5
2 2
DRIVE 2 DRIVE EQCLEAN CHANNEL DRIVE 1
8 8
REVERB
22 POWER:
EXTENSION SPEAKER SOCKET
FX RETURN :
FX SEND :
Socket for connecting external power source.
Socket provided for connecting the output of an external effects device.
Socket provided for connecting an external effects device. The output from this socket should beconnected to the external effect devices input.
FOOTSWITCH SOCKET:
:
Socket provided for connecting the suppliedTF footswitch. TheTF footswitch is adedicated footswitch forTF amplifiers please do not attempt to connect anything other than theTF footswitch suppliedas this may result in serious damage to your amplifier.
Socket provided for connecting an external speaker enclosure. NOTE Theminimum impedance of any speaker cabinet connected to you amplifier must not be less than 8 Ohms. Connecting aload of less than 8 Ohms will result in your amplifier overheating. Whilst this is not a problem in the short term,prolonged use in this manner will result in permanent damage to your amplifier and voiding of your amplifiersguarantee.
16
Eng
Laney OPERATING INSTRUCTIONSTu
be
Fusi
on
-II
172 3 4 6 7 8 9 10 11 12 13 14
24 26
1 5 15
23
16
23
24
17
19 20 21
25
18
22
VIBE:
CLEAN REVERB LEVEL:
DRIVE REVERB LEVEL:
CLEAN CHANNEL SWITCH:
DRIVE 1 CHANNEL SWITCH:
DRIVE 2 CHANNEL SWITCH:
Generates a radical EQ cut and boost. Difficult to explain but easy to hear! Give it a try. Works on both
channels.
Sets the overall level of REVERB present in the clean channel signal.
Sets the overall level of REVERB present in the drive channel signal.
Selects the amplifiers CLEAN channel.
Selects the amplifiers DRIVE 1 channel.
Selects the amplifiers DRIVE 2 channel.
18
19
20
21
25
26
TF300-II Rear Panel/TF320-II
Designed in the UK by BLT Industries LTD.
N1646N1646
MAXIMUM POWER CONSUMPTION300 WATTS ~50/60 HZ
WARNING - THIS EQUIPMENT MUST BE EARTHED.
WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCKDO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOTREMOVE COVERS.NO USER SERVICEABLE PARTS INSIDE. REFERSERVICING TO QUALIFIED PERSONNEL ONLY.
ATTENTION - REMPLACER LE FUSIBLE SEULEMENT PAR LEMEME TYPE ET LE MEME CALIBRE.
ATTENTION - DEBRANCHER LE CORDON D ALIMENTATIONAVANT TOUTE INTERVENTION.
AVIS - RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR.
CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OFFIRE REPLACE ONLY WITH SAME TYPE AND RATED FUSE.
T5A L 115V
T2A L 230V
~
~
T5A L 115V
T2A L 230V
~
~
FUSE RATING & SUPPLY VOLTAGE.
!CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
SERIAL NUMBER
Footswitch
FXReturn FXSend
ExtensionLoudspeaker
8 OHM
MINIMUM IMPEDANCE
Use WithDedicatedTF3 Way Footswitch only.Laney
MADE IN CHINA
TF300-II/TF320-II/TF700-II* Front Panel
Page 6
7 7 7 7 7 77 7 7 7 7
1 1 1 1 1 11 1 1 1 19 9 9 9 9 99 9 9 9 9
3 3 3 3 3 33 3 3 3 3
10 10 10 10 10 1010 10 10 10 10
4 4 4 4 4 44 4 4 4 46 6 6 6 6 66 6 6 6 6
0 0 0 0 0 00 0 0 0 0
5 5 5 5 5 55 5 5 5 5
8 8 8 8 8 88 8 8 8 82 2 2 2 2 22 2 2 2 2
1
POWER
0
INPUT BASSCLEAN TREBLE GAIN GAINDRIVE1 DRIVE2
SCOOPBRIGHT SCOOP
VOLUME VOLUME BASS MIDDLE TREBLE VIBECLEAN
REVERBDRIVE
REVERBMIDDLEVOLUME
7 7
1 19 9
3 3
10 10
4 46 6
0 0
5 5
2 2
DRIVE 2 DRIVE EQCLEAN CHANNEL DRIVE 1
8 8
REVERB
7 7 7 7 7 77 7 7 7 7
1 1 1 1 1 11 1 1 1 19 9 9 9 9 99 9 9 9 9
3 3 3 3 3 33 3 3 3 3
10 10 10 10 10 1010 10 10 10 10
4 4 4 4 4 44 4 4 4 46 6 6 6 6 66 6 6 6 6
0 0 0 0 0 00 0 0 0 0
5 5 5 5 5 55 5 5 5 5
8 8 8 8 8 88 8 8 8 82 2 2 2 2 22 2 2 2 2
1
POWER
0
INPUT BASSCLEAN TREBLE GAIN GAINDRIVE1 DRIVE2
SCOOPBRIGHT SCOOP
VOLUME VOLUME BASS MIDDLE TREBLE VIBECLEAN
REVERBDRIVE
REVERBMIDDLEVOLUME
7 7
1 19 9
3 3
10 10
4 46 6
0 0
5 5
2 2
DRIVE 2 DRIVE EQCLEAN CHANNEL DRIVE 1
8 8
REVERB
TUBE FUSION
172 3 4 6 7 8 9 10 11 12 13 141 5 15 16 18
TF300-II/TF320-II/TF700-II* Front Panel
Eng
Laney OPERATING INSTRUCTIONSTu
be
Fusi
on
-II
TF700-II Rear Panel
23 2422
2625
FX SEND :
FX RETURN :
EXTENSION SPEAKER SOCKET
POWER:
Socket provided for connecting an external effects device. The output from this socket should beconnected to the external effect devices input.
Socket provided for connecting the output of an external effects device.
Socket for connecting external power source.
:
FOOTSWITCH SOCKET:
Sockets provided for connecting external speaker enclosures. NOTE Theminimum impedance of any single speaker cabinet connected to you amplifier must not be less than 8 Ohms.Connecting a total load of less than 4 Ohms will result in your amplifier overheating. Whilst this is not a problem in theshort term, prolonged use in this manner will result in permanent damage to your amplifier and voiding of youramplifiers guarantee.
Socket provided for connecting the supplied TF footswitch. The TF footswitch is adedicated footswitch forTF amplifiers please do not attempt to connect anything other than theTF footswitch suppliedas this may result in serious damage to your amplifier.
Page 7
22
23
24
25
26
N1646N1646MAXIMUM POWER CONSUMPTION
300 WATTS ~50/60 HZ
WARNING - THIS EQUIPMENT MUST BE EARTHED.
WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCKDO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOTREMOVE COVERS.NO USER SERVICEABLE PARTS INSIDE. REFERSERVICING TO QUALIFIED PERSONNEL ONLY.
ATTENTION - REMPLACER LE FUSIBLE SEULEMENT PAR LEMEME TYPE ET LE MEME CALIBRE.
ATTENTION - DEBRANCHER LE CORDON D ALIMENTATIONAVANT TOUTE INTERVENTION.
,AVIS - RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR.
CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OFFIRE REPLACE ONLY WITH SAME TYPE AND RATED FUSE.
T5A L 115V
T2A L 230V
~
~
T5A L 115V
T2A L 230V
~
~
FUSE RATING & SUPPLY VOLTAGE.
!CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
SERIAL NUMBER
Footswitch
FXReturnFXSend
Use With DedicatedTF3 Way Footswitch only.
Loudspeakers4 OHM MINIMUM IMPEDANCETOTAL
REFER TO USER MANUAL FORRECOMMENDED CONNECTION Laney
Designed in the UK by BLT Industries LTD.
MADE IN CHINA
Note
s
Page 8
Page 9
Tech
nic
al
Speci
fica
tioin
s
TF200 TF300 TF700
Input Sensitivity
Clean
Drive 1
Drive 2
Input Impedance
FX Loop
Output Power 4 ohm
Output Power 8 ohm
Size (H*W*D)
Weight (Kg)
/(TF320)
20mV 20mV 20mV
850uV 850 V 850 V
100 V 100 V 100
1Meg/47pF 1Meg/47pF 1Meg/47pF
850mV 850mV 850mV
65W 120W 120W
48W 80W 80W
475*534*270 255*578*242
16Kg 12Kg
u u
u u uV
485*575(680)*280
18Kg (24kg)
(Zout 1K/Zin 22K) (Zout 1K/Zin 22K) (Zout 1K/Zin 22K)
In the interest of continued product development BLT Industries Ltd. Reserves the right to amend product specification without prior notification.
POWER TO THE MUSICLaney
top related