TRD Beholder MS1 Camera Stabilizer · Battery Setup and Charging Battery Setup a. Install batteries positive side up into battery holder. Connect the Micro USB cable to the Battery
Post on 05-Sep-2019
9 Views
Preview:
Transcript
1 © 2015 Beholder All Rights Reserved
Table of Content
Brief Introduction
Kit Includes
Battery Setup and Charging
Camera Setup and Balancing
How to Use
Other Features
Supported Cameras
Licensing and Trade Mark
Specifications
1
2
2
4
5
7
9
7
8
Brief Introduction
The Beholder MS1 Camera Stabilizer is designed to support professional videographers of all levels. The stabilizer is easy to use and small enough to travel with. The Beholder MS1 Stabilizer is intuitive and offers a greater range of camera movement.
Attention 8
Battery Setup and Charging
Battery Setup
a. Install batteries positive side up into battery holder. Connect the Micro
USB cable to the Battery Holder Micro USB port. Connect USB cable
to 1.5- 2 amp power supply.
b. Battery Charging time 4- 5 hours.
c. Green light means fully charged. Red light means charging. Flashing
Red and Green lights means almost fully charged.
d. Warning using a charger that does not support 1.5- 2 amps will result
in batteries failing to charge.
2 © 2015 Beholder All Rights Reserved
Kit Includes
MS1
Adapter plate Quick Release Plate Two 1/4" Lanyard USB- LED Light
Battery Holder Three Batteries 18650 Micro USB Cable
Battery Holder
a. Battery Holder positive side up.
b. Insert Battery Holder into handle, positive side first.
c. Screw on battery cap and make sure the cap is secured snuggly.
3 © 2015 Beholder All Rights Reserved
Camera Setup and Balancing
1. Attach the quick release plate as shown with the longest slide pointing out towards the direction of the lens. Snuggly tighten the camera screw.
4. Adjust the front and rear balance. Once gimbal is balanced, tighten the quick release lock. If the camera does not balance perfectly.Don't worry.The MS1 will usually be able to maintain stability.
4 © 2015 Beholder All Rights Reserved
2. Attach the camera with plate to stabilizer. Adjust the camera's position so that the gimbal remains level.
3. Adjust the left- right balance of the camera. Small adjustments maybe needed.
How to Use
A. To start the stabilizer with the camera and gimbal level on a flat surface at 90 degrees and then press the power button.
Note: Starting the stabilizer in a position other than 90 degrees will result in performance issues.
B. Joystick mode selection.
a. Press once for Lock Mode this mode will make the stabilizer hold a position.
b. Press again to change to Follow Mode which will make the stabilizer follow the pan and tilt of your hand.
5 © 2015 Beholder All Rights Reserved
Installation of special adapter for hard to balance camera
1. Attach the single sided anti slipping materials onto the
adapter plate.
2. Attach the anti slip side onto the base of the camera
and lightly tighten the 1/4" screw.
3. Attach the whole unit onto the quick release plate*.
*try different screw anchoring holes for best result,
you might have to try out many times to register the
appropriate anchoring hole for the best balancing
result.
4. Adjust the camera position on the adaptor plate,
fine tuning screw position on the quick release plate to
achieve a perfect balance repeating steps A- B.
5. Tighten all screws and knob. Loose space in between
camera and adaptor, adaptor and quick release plate
and quick release plate and unit will result in rattling
noise and shaking movement while unit is in operation
later.
6 © 2015 Beholder All Rights Reserved
d. Use the joystick to pan and tilt the camera.
c. Press and hold the joystick for 3 seconds to calibrate the gyro. The gyro controls the horizontal level. During calibration the MS1 must not be touched and the gimbal must be level.(If the camera moves automatically or unbalanced, please use this function. Just keep the system steady on the table during the calibration process and prevent any movement or vibration.)
Instruction of Inverted shot mode
1.The default mode of MS1 is non- inverted shot mode .If you want to change to the inverted shot mode, please press the little button on the right side of the pan (Reset button ) twice. After three seconds, you will heard a sound of mode switching. Meanwhile, the compensation direction is opposite to the rotation axis, which will cause it rotate usually. That means MS1 is in inverted shot mode and the handle can be inverted.2. When inverted,the five ways multi mode control can be used normally. You can switch to lock mode or follow mode,but the operational direction is opposite to the normal direction .3. When in the inverted shot mode , redo the stept 1,then you can change it back to non- inverted shot mode.4. When shutting down the system the shot mode will not be restored to its default. It will retain the former mode when you shut the system down.
7 © 2015 Beholder All Rights Reserved
Other Features
A.The stabilizer can be mounted to a tripod, selfie stick, and more.
B. LED USB light is great for shooting at night.
C.Charge a cellphone from stabilizer. Note stabilizer must be off.
Supported Cameras Sony A7S, NEX series, Panasonic DMC, GH4, BMPCC, RX100, A6000, Canon G7x, A7ii, and more.
Battery Status
Power LED Indicator Status
Green light
Red light
Flashing Red
Normal
Low battery
Batteries need to be charged. Also the MS1 will shut down to protect the batteries.
Licensing and Trade Mark
Beholder® is the licensed trademark of TRD Beholder.Website: http://www.teamrebeldesign.com/ Email: Beholder@TeamRebelDesign.com
AttentionA. Please calibrate the gyro if your camera moves automatically or unbalanced. Gyro calibration: Place the MS1 on a flat surface. Make sure the camera is balanced in the gimbal. Press and hold the joystick in for 3 sec. If balance is not correct try again calibrating. Keep the MS1 steady on the table during the calibration process and prevent any movement or vibration.
B. USB Ports: The USB located on the handle is a 5V 0.5A power output. The Micro USB located on the handle is for remote control. The Mini USB located on the gimbal is for accessing the 8- Bit board PID settings through Simple BGC 8- Bit 2.40b7.
8 © 2015 Beholder All Rights Reserved
9 © 2015 Beholder All Rights Reserved
Height:
Width: 123mm 4.8 Inches.
Yaw:
Roll:
Weight W Battery:
Packaging Dimensions:
Battery Life:
168mm 6.6 Inches.
Weight W/O Battery: 720g
Unit with Packaging: 1580g
Maximum SupportedCamera Weight:
Range of Motion: 90-180°
Pitch:
Battery: 3* 3.7v Li-ion 18650 2600mAh
Electronics:
268mm 10.5 Inches.
860g
355+-180°
355+-60°
3 Hours.
355°
8-Bit board 2.40b7: 3-Axis Stabilizer gyro system
Supported Camera Models:
Specifications:
Length:
Sony A7S, NEX series, Panasonic DMC, GH4, BMPCC, RX100, A6000, Canon G7, A7ii, and more.
1000g
390x200x100mm, 15.4x7.9x3.9 Inches.
top related