Thermocouple/RTD - DFS Gauges · improved system accuracy. ... Field calibration capability minimizes sensor errors. Thermometer accepts 100 ohm platinum ... Sensors have 5-1/2”
Post on 21-May-2018
216 Views
Preview:
Transcript
Thermocouple/RTDHand Held Thermometers
Features: Rugged ABS case and sealed keypad for an IP54 splash proof rating. Hold button freezes display for later reading. Easy to use, field calibration “capture” mode for improved system accuracy. Accuracy ±0.4°F(±0.2°C). Selectable °C or °F scale. Field calibration capability minimizes sensor errors. Thermometer accepts 100 ohm platinum RTD sensors. (sold separately)
Thermocouple Model 600-1040The thermocouple thermometer offers a max/min display anddifferential readings simultaneously using one or two sensorson selectable, easy read, multi-data LCD. Meter automaticallystores and adjusts for inherent sensor error.
RTD Model 600-1080The Platinum RTD Thermometer is an easy-to-use, minimally featured meter, ideal for your basic temperaturemonitoring applications. Four button keypad: On/Off, C/F for °C or °F scale, Hold and CAL. CAL button - easyone button, “capture” mode, or a single (ice) point field calibration offset. Field Calibration lockout featureprevents tampering and protects factory settings.
Specifications:Display: LCDOutput: InfraredPower: 2 AA Batteries (inc)Battery Life: 300 hrsLow Battery IndicatorDimensions:W = 3.3” (84mm)H = 6.2” (158mm)D = 1.2” (30mm)Shipping Weight:1 lb (0.5 kg)
Features: Max/Min, hold, °C or °F, Multi-Data LCD. Accepts 2 thermocouple inputs and either J, K, T or E thermocouples. Manually stores up to 25 readings in memory. T1/T2 differential. Accuracy to ±0.7°F (±0.4°C) plus ±0.1% of reading. UL, cUL approved for Class I, Div I; Groups ABCD hazardous (classified) locations. Meets CE requirements for electromagnetic compatibility. Rated IP54 for splash and dust resistance. ABS/polycarbonate impact resistant case Bright, easy-to-read LCD.
Specifications:Power: 2 AA BatteriesBattery Life: 750 hrsLow Battery IndicatorDimensions:W = 3.3” (84mm)H = 6.2” (158mm)D = 1.2” (30mm)Shipping Weight:1 lb (0.5 kg)
Sensor
Connection,
type
Platinum -58 to 302°F ±0.4°F 3-pin (round)RTD Thermometer (-50 to 150°C) (±0.2°C) 100-ohm platinum RTD
Range Accuracy Resolution
600-1080 0.1°
Model # Type
Model # Type Range Accuracy Resolution Functions Display
-328° to 1832°F
(-200° to 1000°C) ±0.7°F(±0.4°C) above -238°F(-150°C) 0.1° between On/off, hold, calibration
-418° to 2501°F plus ±0.1% of reading -238°F(-150°C) and 999.9° °C/°F,
-250° to 1372°C J-T-E-K, maximum, Three 4-digit LCD
-418° to 752°F minimum, differential, store, Displays: 0.4"H and 0.2"W
-250° to 400°C ±2°F(±1°C) below -238°F(-150°C) 1.0° below -238°F(-150°C) recall, display, resolution
-418° to 1832°F plus ±0.25% of reading 1.0° and 999.9°
-250° to 1000°C
600-1040
J
K
T
E
6-2February, 2006
Thermocoupleextension handle
Increase your sensorreach by 41”
Ideal for out-of-reach areas,such as ceiling air ducts.Extended to its full length, thistelescoping extension handleadds 41” to your detachablesensor (retracted length is 17”). Use with general-purpose,air/gas and surface detachable-sensors (not recommended forpiercing sensor). Features ABS plastic pistol-grip handle and ANSI colour-coded, 5-ft, PVC coiled cablewith miniconnector.
Accessories
Type J, K and T thermocouplethermometry kits
Everything you need for convenient field measurements- in one kit!Each kit includes on thermometer, three probes and acarrying case, These kits combine everything you need for field measurements - all in one convenient package! Choose your kit with type J, K and T thermocouple thermometer.
Your complete kit includes on thermometer (type J, K or T), three integral-handle sensors (air/gas, surface, and general-purpose), one 9V battery, instructions and carrying case. Sensors have 5-1/2” L glass-filled nylon handles. The 5-ft. coiled PVC cables are ANSI color-coded.
Hand-heldAccessories
Carrying case for allthermocouplethermometers
Designed to hold yourthermocouple thermometer andon sensor - this Cordura clothcase keeps everything togetherfor quick and convenient access.Order one durable case for eachof your thermometers!
Your thermometerkit includes thesethree integralhandle sensors...air/gas sensor...surface sensor...general- purpose sensor
6-3February, 2006
Digital Temperature TransmitterUniversally programmable, Head Mounting
Model T12.10.006
Electronic Temperature Measurement
• Universally programmable forRTD’sThermocouplesResistance-sensormV-sensor
• Output linear to temperature with input signal from RTD’sand thermocouples
• Analog output 4...20mA, invertable, 2-wire design• Signalling configurable for sensor burnout and sensor
short circuiting• C.S.A. intrinsically safe for hazardous locations,
Class I, Groups A, B, C, & D• Galvanic isolation• 100% Rh protection, moisture condensation permissible• Increased ambient temperature• PC-configurable, Windows-programme
Interesting facts about the T12 transmitter seriesThe digital temperature transmitter T12 range is designedfor universal industrial use.Comprehensive configuration possibilities: for example,type of sensor, measuring range and error signalling, reliable accuracy, galvanic isolation and EMI protection characterize these transmitters.
During configuration any one of 16 input signals can beselected. Measured temperatures are from -200°C up to +2300°C.
The following sensors can be connected:
• RTDs with 2, 3 and 4 lead connection, the connectionsystem used is configurable and ensures an optimallead wire compensation.
• thermocouples per IEC 584, DIN 43710 and ASTM E988Cold junction compensation (CJC) is built-in, the use ofan external CJC is selectable Via configuration.
• resistance-sensors up to 5 kW in 2, 3 and 4 lead connection, configurable compensation of the connection cable.
• mV sensors up to 800 mV.
Configuration is done by means of a standardDOS PC using the Configuration-Set. W ith theConfiguration Software the required parametersare defined. Data to the T12 is down loaded usinga Communication-Interface (Programming Unit).The bi-directional communication enables displaying the measured values on the PC.
Configuration can be done while the transmitter ismounted in the field. The Communication interface has an integral isolation barrier whichallows configuration while the transmitter is withinhazardous areas, and acts to protect the PC.Configuration sets are available as an optionalextra.
The transmitters are delivered with a basic configuration (see order information). Uponrequest, transmitters can alternatively be delivered with a customized configuration withinthe given limits.
6-4February, 2006
28
.5 m
m
33 mm
22
mm
6 mm Æ
49.5 m
m Æ
Dimensions in mm
-
+3
44
2
1
=
2
3
-
+
2
3
1
4
3
1
4
1
2
3
mV-sensor RTD / resistance-sensor thermocouple 4...20mA-loop
-
+
Designation of terminal connectors
Input
Load diagram
0
0
9 24 30(Ex)
36
UB in Volt
714
1000
1286
load RA in W
NoteThe permissible load isdependant upon theloop power supply voltage
*
*
* If cold junction compensation is used with an external RTD (2-lead connection)then terminal 1+ and terminal 4 -
6-5 February, 2006
Input configurable: type of sensor and measuring range max. measuring range min. measuring span(1)
RTD’sPt 100 EN 60 751 -200...+850ºC 25ºC
Ni 100 DIN 43760 : 1987-09 -60...+500ºC 25ºC
Thermocouples type T, Cu-CuNi IEC 584 -200...+400ºC 50ºC
type E, NiCr-CuNi IEC 584 -100...+1000ºC 50ºC
type J, Fe-CuNi IEC 584 -100...+1200ºC 50ºC
type L, Fe-CuNi DIN 43710 : 1985-12 -100...+900ºC 50ºC
type K, NiCr-Ni IEC 584 -180...+1372ºC 50ºC
type N, NiCr-Ni IEC 584 -180...+1300ºC 100ºC
type U, Cu-CuNi DIN 43710 : 1985-12 -200...+600ºC 75ºC
type R, PtRh-Pt IEC 584 -50...+1760ºC 200ºC
type S, PtRh-Pt IEC 584 -50...+1760ºC 200ºC
type B, PtRh-PtRh IEC 584 +400...+1820ºC 200ºC
type W3, W3Re/W25Re ASTM E988 0...+2300ºC 200ºC
type W5, W5Re/W26Re ASTM E988 0...+2300ºC 200ºC
Resistance-sensor 0...5 kW 30 WmV-sensor -10...800 mV 5 mV
RTD/resistance-sensor
accuracy 0.2ºC or 0.1ºC + 0.05% span, whichever is greater
sensor current approx. 0.2 mA
temperature coefficient withmeasuring span
< 100ºC or < 38.5 W ±0.01ºC /ºCT amb(2) or ±0.004 /ºCT amb(2)
> 100ºC or > 38.5 W ±0.01% of measuring span /ºC T amb(2)
lead wire connection configurable: 2-lead, 3-lead, 4-lead
max. permissible resistance of connection leads 30 each lead, 3-lead symmetric
lead wire effect < 0.02 / 10
signalling of sensor error configurable
Thermocouple
accuracy(4) 0.5ºC or 0.1ºC + 0.05% (3) span, whichever is greater
cold junction compensation < ± 1.0ºC
temperature coefficient
type T, E, J, L, K, N, Umeasuring span < 500ºC ±0.05ºC /ºCT amb(2)
measuring span > 500ºC ±0.05ºC /ºCT amb(2)
type R, S, B, W3, W5 0.2ºC /ºCT amb(2)
testing current to monitor sensor nom. 33 µA during testing cycle, otherwise 0 µA
signalling of sensor error configurable
mV-sensor
measuring deviation per DIN IEC 770, 23ºC ± 5ºC < 10 µV or 0.05% (3) whichever is greater
input resistance ³ 10MWAnalog output for measuring range configurable: 4 ... 20 mA or 20 ... 4 mA, 2-wire design
with type of sensor RTD’s linear to temperature per EN 60 751 / DIN 43 760 : 1987-09
with type of sensor thermocouples linear to temperature per IEC 584 / DIN 43 710 : 1985-12 / ASTM E988
by simulation mode independent from input signal,simulation value configurable from 4 mA up to 20 mA
output limits configurable
application specificaton configurable from 3.6 mA up to 21.5 mA
NAMUR NE 43 lower limit 3.8 mA upper limit: 20.5 mA
not active A lower limit 3.6 mA upper limit: 21.5 mA
load RA load RA £ (RB - 9V) / 0.021 A with RA in W and UB (5) in Volt
load effect < ±0.01% of measuring span / 100 Wmeasuring deviation per DIN IEC 770, 23ºC ± 5ºC < ±0.05% of measuring span
temperature coefficient < ±0.01% of measuring span /ºC
damping configurable: minimal 0.5s, 1 s up to 60 s
measured value update approximately 2/s
power supply effect < 0.005% of measuring span / V
Total measuring deviation for input and output per DIN IEC 770, 23ºC ± 5 °C
RTDs / resistance-sensor < 0.2 °C + 0.05%(6) or < 0.1 °C + 0.1% (6), whichever is greater
thermocouples < 0.05% + (0.5°C or 10µV or 0.05%), whichever is greater
mV-sensor < 0.05%(6) + (10µV or 0.05% (3)), whichever is greater
Signalling < 0.05%(6) + (10µV or 0.05% (3)), whichever is greater
analog output with sensor error or withinternal male-function
configurable
substitute value configurable from 3.5 mA up to 23.0 mA
up scale NAMUR NE 43 > 21.0 mA
down scale NAMUR NE 43 > 3.6 mA
Specifications
(1) beginning of measuring range maximum 50% of end of measuring range(2) T amb = ambient temperature
(3) of final value
(4) valid only for configurated measuring range with beginning ³ 0 ºC(5) UB = loop powersupply voltage, see power supply
(6) of measuring span
6-6February, 2006
Power supply UB
model T12.10.006 DC 9...36 V
maximum values for connection tocertified intrinsically safe circuits
Uo = 30V I K = 100mA P = 705mWsee certificate of conformity for additional data
Electromagnetic compatability (EMC) CE-conformity per DIN EN 50081-1 (March 93) and DIN EN 50082-2 (Feb 96)
Special features
isolation voltage (input versus analog output) 1500 VAC, 60 s
electric protection protected against reverse polarity
ambient and storage temperature
standard range -40...+85ºC
option: increased range min. -50ºC max. +105ºC
humidity100% relative humidity (unlimited with isolated sensor connection wires)
moisture condensation permissible IEC 68 2-30 Var. 2
vibration 10 ... 2000 Hz 5g DIN IEC 68 2-6
shock DIN IEC 68 2-27 gN = 30
salt fog DIN IEC 68 2-11
configuration and calibration data permanently stored in EFPROM
self-monitoringautomatic execution of initial test after connection to power supply ,
thereafter monitoring due to internal male-function
warm-up time approx 5 Min.
power consumption with UB, 24 V max. 552 mW
communication-interface Programming Unit (part of the configuration-set available as an accessory)
guarantee5 years for performance with standard range of ambient temperature,
legal warranty with enlarged range of ambient temperature
Case for head mounting
material plastic
cross section of terminal connections max 1.5 mm², screws captive
weight approx. 70 g
dimensions see drawings
Accessory Configuration-SetThe Configuration-Set contains • configuration Software (3.5” disk. Online Help) • connection cable. RS 232-C (9-pin sub-D-plug)• plug adapter (25-pin to 9 -pin sub-D-plug) • programming Unit (Communication-interface) incl. 9 V battery • connecton cable Programming Unit - T12
Receivingequipment
Input+
-
Hazardous area
T12.10.006
+
-
Safe area
Disconnectred
black
yellow*
green*
*Yellow and green are connected only ifconfiguration of the T12 is to be madeduring operation.
RS 232-C
ProgrammingUnit
COM
Mounting materialto use for mounting• in the top of connection head• on a measuring insert, spring-
loaded• on a standard rail
The wiring scheme shown below must be observed, particularly if the digital temperature transmitter series T12 is installed in the hazardous area.
6-7 February, 2006
6-8February, 2006
6-9 February, 2006
6-10February, 2006
6-11 February, 2006
6-12February, 2006
6-13 February, 2006
6-14February, 2006
6-15 February, 2006
6-16February, 2006
6-17 February, 2006
6-18February, 2006
6-19 February, 2006
6-20February, 2006
6-21 February, 2006
Fieldbus Temperature Transmitter Model T5350 B
Page 1 of 4WIKA Data Sheet TE 53.01 · 06/2004
WIKA Data Sheet TE 53.01
PROFIBUS PA Temperature transmitter, Model T42.10, see data sheet TE 42.01
Applications
Process industry Machinery, plant construction
Special Features
FOUNDATION™ Fieldbus ITR 4.01 PROFIBUS® PA Profile 3 Automatic switch between protocols Explosion protection, EEx i, intrinsically safe / FISCO Explosion protection, EEx n, FNICO
Description
Fieldbus Transmitter with FOUNDATION™ and PROFIBUS® PA Fieldbus Communication for temperature measurement with resistance thermometers and thermocouples.Difference, average or redundancy temperature measurement. Resistance and mV-measurements with or without customer specific linearisation of functions.
FOUNDATION Fieldbus with LAS-Functionality (Link Active Sche-duler) and PID-Regulation. This functionality allows for Master-independent regulations in the field device.
Polarity-independent bus connection.
Small dimensions, suitable for DIN form B sensor head moun-ting.
Delivered with a basic configuration (according to the ordering options) or customer specific configuration in line with the configuration options.
Fieldbus Temperature TransmitterModel T5350, for FOUNDATION Fieldbus and PROFIBUS PA
ElectricalTemperature Measurement
6-22February, 2006
Specifications Model T5350
Input configurable Sensor Measuring range Standard Resistance thermometer Pt25 ... Pt1000 -200 °C ... +850 °C IEC 60 751/JIS C
Pt25 ... Pt1000 -200 °C ... +850 °C IEC 60 751/JIS C1604Ni25 ... Ni1000 -60 °C ... +250 °C DIN 43 710Cu10 ... Cu1000 -50 °C ... +200 °C α = 0,00427
Thermocouples B +400 °C ... +1820 °C IEC 584E -100 °C ... +1000 °C IEC 584J -100 °C ... +1200 °C IEC 584K -180 °C ... +1372 °C IEC 584L -200 °C ... +900 °C DIN 43 710N -180 °C ... +1300 °C IEC 584R -50 °C ... +1760 °C IEC 584S -50 °C ... +1760 °C IEC 584T -200 °C ... +400 °C IEC 584U -200 °C ... +600 °C DIN 43 710W3 0 °C ... +2300 °C ASTM E988-90W5 0 °C ... +2300 °C ASTM E988-90
External CJC (cold junction compensation) -40 °C ... +135 °C Resistance sensor 0 ... 10 k Ω Potentiometric resistance sensor 0 ... 100 k Ω mV - sensor -800 ... +800 mV Basic configuration Pt100, 3 wire 0 °C ... 100 °C Sensor current typically 0.2 mA Max. cable resistance 50 Ω per wire Accuracy, at 24 °C ± 4 K Sensor Base accuracy Temperature coefficient
Pt100 und Pt1000 ≤ ± 0.1 °C ≤ ± 0.002 °C / °CNi100 ≤ ± 0.15 °C ≤ ± 0.002 °C / °CCu10 ≤ ± 1.3 °C ≤ ± 0.02 °C / °CLin. R. ≤ ± 0.05 Ω ≤ ± 0.002 Ω / °CVolt ≤ ± 10 µV ≤ ± 0.2 µV / °CTE-Typ: E, J, K, L, N, T, U ≤ ± 0.5 °C ≤ ± 0.01 °C / °CTE-Typ: B, R, S, W3, W5 ≤ ± 1 °C ≤ ± 0.025 °C / °C
Error cold junction compensation (CJC) ± 0.5 °COutput FOUNDATION™ Fieldbus PROFIBUS ® PA Version Version ITK 4.51 EN 50 170 vol. 2 / profile 3 Functionality Basic or LAS Fieldbus function blocks 2 analogue and 1 PID 2 analogue Execution time, PID-controller < 200 msPower supply S upply voltage 9 ... 32 VDC (maximum values specified in the type-examination certificate are to be observed) Current consumption < 11 mAExplosion protection Model 5350 B Model 5350 A d protection (ATEX) Zone 0/1, category 1G, 2G Zone 1, category 2G Zone 2, category 3G
Ignition protection type EEx ia IIC T4/T5/T6 EEx ib IIC T4/T5/T6 EEx nA[L] IIC T4/T5/T6EC- type-examination certificate KEMA 02 ATEX 1318 KEMA 03 ATEX 1011X
FM IS, Class I, Division 1, Group A, B, C, DNon-Incendive, Class I, Division 2, Group A, B, C, D
Non-Incendive, Class I,Div. 2, Group A, B, C, D
Installation Drawing 5350QE01 5350QE01
ULClass I, Division 2, Group A, B, C, DClass I, Zone 0 & 1 Group IIC,Class II, Division 1, Group E, F & G
Class 1, Division 2,Group A, B, C, DCl. I, Zone 2 Group IIC
CSA IS, Class I and II, Division 1,Groups A, B, C, D, E, F, G
IS, Class I, Div.2,Groups A, B, C, D
Non-Incendive, Class I,Div.2, Group A, B, C, D
Certificate No. 1418937 1418937Maximum values for connectionof the current loop circuit
Po< 0.84 W
Po< 1.3 W FISCO FISCO Po
< 5.32 W FISCO FNICO
S upply voltage Ui 30 VDC 30 VDC 17,5VDC
15 VDC 30 VDC 17.5VDC
32 VDC Ampacity Ii 120 mA 300 mA 250 mA 250 mA Power rating Pi 0.84 W 1.3 W 2.0 W 5.32 W Internal capacitance Ci 2 nF 2 nF Internal inductance Li 1 µH 1 µH Medium temperature/ ambient temperature
T4: < 85°CT5: < 75°CT6: < 60°C
T4: < 75°CT5: < 65°CT6: < 45°C
T4: < 85 °CT5: < 75 °CT6: < 60 °C
T4: < 85 °CT5: < 75 °CT6: < 60 °C
T4: < 85 °CT5: < 75 °CT6: < 60 °C
Maximum values for connectionof the sensor circuit
S upply voltage Uo 5.7 V Ampacity Io 8.4 mA Power rating Po 12 mW Capacitance Co 40 µF Inductance Lo 200 mH
6-23 February, 2006
Designation of terminal connectors
2099
318.
011 Sensor
2 Sensors
Potentiometric sensor
Further specifications Model T5350
Electromagnetic compatibility (EMC) per EMC Directive 89/336/EWG DIN EN 61 326:2002and NAMUR NE 21
Ambient conditions Ambient and storage temperature Standard range: -40 … +85 °C Maximum permissible humidity 95 % relative humidity, without moisture condensation Vibration 2 … 100 Hz 2 g DIN EN 60 068-2-6Special features Isulation voltage, test / operation 1.5 kVAC / 50 VAC Response time (programmable) 1 ... 60 s Updating time < 400 msCase Head mounting design, incl. spring-loaded mounting screws Material Plastic, PBT, glass fibre reinforced Ingress protection case IP 50 IEC 529 / EN 60 529
terminalconnections
IP 00 IEC 529 / EN 60 529 Cross section of terminal connectors 0.14 … 1.5 mm² Weight Approx. 0.05 kg
Clamp 1 and 2: Connection FOUNDATION™ Fieldbus or PROFIBUS® PA (protected against reverse polarity)
6-24February, 2006
2099
288.
01
1) Basic configuration: Pt100, 3 wire, 0 ... 100 °C2) Please pay attention to the sensors and the limits of measuring ranges on page 2.
Ordering information
WIKA Alexander Wiegand GmbH & Co. KGAlexander-Wiegand-Straße 3063911 Klingenberg/GermanyPhone (+49) 93 72/132-0Fax (+49) 93 72/132-406E-Mail info@wika.dewww.wika.de
Specifications and dimensions given in this leaflet represent the state of engineering at the time of printing.Modifications may take place and materials specified may be replaced by others without prior notice.
Dimensions in mm
Screw M4approx. 30 mm spring-loaded
Field No. Code Features
Explosion protectionA II 3 G EEx nA[L] II C T4/T5/T6, CSA/FM/UL Division 2
1 B II 1 G EEx ia IIC / II 2 G EEx ib IIC T4/T5/T6, CSA/FM/UL Division 1Measuring range
GK basic configuration 1)
5 KK customer’s specification 2) please state as additional text
Additional order infoYES NO
6 T Z additional text Please state as clearly understandable text!
Order code:
1 2 3
T5350 - -
Additional text:
6-25 February, 2006
top related