Transcript
World Standard‘Strong’, ‘High’ and ‘Less’ are keywords that everyone in the world understands
CX-400SERIES
PHOTOELECTRIC SENSOR
COMPACT PHOTOELECTRIC SENSOR Amplifier Built-in
Conforming toEMC Directive UL Recognition
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
1
‘Strong’, ‘High’ and ‘Less’: three keywords that reflect the fundamental concepts in the design and operation of our sensors.Strong: meaning being able to maintain fully reliable and stable levels of performance, no matter how adverse the work environment.High: meaning technology-backed high detectability.Less: meaning less waste, less time lost, less power consumption, less human and natural resources needed.We bring you the ideal standard sensors for the 21st century.
We have a full lineup of world standard photoelectric sensors!
Output NPN, PNP Connecting method Cable type, M8 Plug-in connector type,
M12 Pigtailed type Cable length of cable type 0.5 m 1.640 ft, 2 m 6.562 ft, 5 m 16.404 ft
Refer to p.9 l for ‘ORDER GUIDE’.
Special transparent object circuit enhances detectability!
Retroreflective type for transparent object sensingCX-482/481
Sensing range2 m 6.562 ft / 0.5 m 1.640 ft
A bright, spot at approx. "5 mm "0.197 in
The smallest spot in the industry at approx. "2 mm "0.079 in
A long range and small spot!
Sensing range70 to 200 mm2.756 to 7.874 in
Sensing range300 mm 11.811 in / 100 mm 3.937 in / 50 mm 1.969 in
A bright spot at approx. "2 mm "0.079 in
Retroreflective typeCX-493/491
Sensing range5 m 16.404 ft / 3 m 9.843 ft
Sensing range15 m 49.213 ft / 10 m 32.808 ft
Thru-beam typeCX-412/411
Diffuse reflective typeCX-422/421/424
Sensing range800 mm 31.496 in / 300 mm 11.811 in / 100 mm 3.937 in
Diffuse reflective • narrow-view typeCX-423
Adjustable range reflective typeCX-442/444/443/441
100 mm3.937 in300 mm
11.811 in800 mm31.496 in
15 m49.213 ft
CX-441
100 mm3.937 in
200 mm7.874 in
A height difference equal to the thickness of one business card can be detected!
Full line up 116 models!
Full line up 116 models!
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
2
Long range sensing desired Thru-beam type
Rertroreflective type
Diffuse reflective type
Longest in its class with a distance of 15 m 49.213 ft
Longest in its class with a distance of 5 m 16.404 ft
Long sensing range 800 mm 31.496 in
Small parts sensing desired
Minute height difference discernment desired (Background present)
Glossy object sensing desired
Area prone to dirt and dust
Oil is scattered about
Simple light beam axis adjustment desired
Precise transparent object sensing desired
CX-412
CX-493
CX-422
Thru-beam type
Rertroreflective type
Adjustable rangereflective type
Sensing range 15 m 49.213 ft / 10 m 32.808 ft
Polarizing filter built-in
FGS function ensures stable sensing
CX-411/412
CX-491
CX-44
Thru-beam type
Diffuse reflective type
Rertroreflective type
Uses acrylic for lens surface for superior oil resistance
Uses acrylic for lens surface for superior oil resistance
Uses acrylic for lens surface for superior oil resistance
CX-41
CX-42
CX-49
Fit slit for thru-beam type
Diffuse reflective • narrow-view type
Minimum size for sensing object "0.5 mm "0.020 in with slit fitted
LED light source realizes a spot diameter of approx. "2 mm "0.079 in
CX-411
CX-423
Adjustable rangereflective type
Approx. "2 mm "0.079 in spot unaffected by background objects CX-441
Thru-beam type
Adjustable rangereflective type
Uses penetrating infrared light
Judgment based on incidence angle to avoid light-receiving amount swaying
CX-412
CX-44
Diffuse reflective • narrow-view type
Adjustable rangereflective type
The bright spot makes the beam axis clearly visible
The bright spot makes the beam axis clearly visible
CX-423
CX-44
Adjustable rangereflective type
High precision, 0.4 mm 0.016 in height difference sensing possible
Long sensing range 300 mm 11.811 in / 100 mm 3.937 in
CX-441/443
CX-442/444
Rertroreflective type
High precision type with built-in special transparent object circuit
Built-in special transparent object circuit. Long sensing range 2 m 6.562 ft.
CX-481
CX-482
CX-400 Series Selection CX-400 series sensors solves all your sensing troubles.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
Compact size
CX-482
20 mm0.787 in
Digital laser sensorLS series
CX-400 series
0.5 m1.640 ft
Cable type
Great maintainability No unnecessary cables or terminal blocks11.2 mm0.441 in
Industry standardmounting pitch
25.4 mm 1.000 in31 mm1.220 in
5 m16.404 ft
2 m6.562 ft
M12 pigtailedtype Straight
M8 plug-inconnector
type Elbow
Straight
(2 m 6.562 ft / 5 m 16.404 ft )(2 m 6.562 ft / 5 m 16.404 ft )
(2 m 6.562 ft / 5 m 16.404 ft )
Oil
‘Strong’ against even the harshest conditions guarantees reliability.
The ideal sensors that are people and environmentally friendly are born from the concept of ‘less’ waste.
The lens material for the thru-beam type, retroreflective type (excluding the CX-48) and the diffuse reflective type are made of a strong acrylic that resists the harmful effects of coolants. These sensors can be used with confidence even around metal processing machinery that disperses oil mists. The protection mechanism also conforms to IP67 (IEC).
Interference prevention filter (Optional) Thru-beam type
Only CX-411
Retroreflective type
Diffuse reflective typeAdjustable range reflective type
Strong against oil and coolant liquids
CX-41/42/49
M8 plug-in connector type and M12 pigtailed type are available. This contributes to less time spent in setting up. In addition, cable types are available with cable lengths of 0.5 m 1.640 ft, 2 m 6.562 ft and 5 m 16.404 ft. This results in less wastage.
Less processingThe sensors are compact in size at W11.2 H31D20 mm W0.441H1.220D0.787 in. The mounting pitch is also at the world standard size of 25.4 mm 1.000 in.
Less space
A strong, ethanol resistant polycarbonate was used for the front and display covers. Safe even for installing near food processing machinery that disperses ethanol based detergents. The protection mechanism also conforms to IP67 (IEC).
Strong against ethanolCX-44/48
Stable performance can be maintained even in environments of 25 C 13 F .
Strong even in cold environments
Twice the sensing range!
m
Power consumptionLess energy
NoiseStrong
Strong
Significantly stronger against inverter light and other extraneous light as well as high frequency and electromagnetic noise generated by high-pressure inverter motors and other devices.
Strong against noise
Inverter motor
Fluorescent light tube
The interference prevention function lets two sensors to be mounted close together precisely.
Strong against interference
CX-400
Conventional product
Automatic interferenceprevention function
Strong
Strongest in its class
m As of April 2004 and based on research conducted by SUNX.
Easy to use high-level functions!
3Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
CX-482CX-482
A maximum 45 % reduction compared to conventional sensors!!
1
0
2
Precision
The new standard sensors for the 21st Century provide ‘high’ performance detection.
High precision optics and high performance special circuitry
These sensors realize a high luminance red spot that provides bright visibility. The sensing position can be checked at a glance.Because it has the smallest spot in its class, approx. "2 mm "0.079 in (CX-423/441), even the minutest object can be accurately detected.
BGS / FGS functions make even the most challenging settings possible. Controls the adverse effects of background objects.
Even different colored object can be sensed at roughly the same distance. No adjuster control is needed when the setup is changed.
A full range of 2 m 6.562 ft sensing range types are available. They are capable of sensing a 10 !m transparent film even at a long range.
High luminance spot
The CX-400 series sensors achieve a maximum of approx. 55 % the power consumption of conventional sensors.Contributes to preserving the environment.
Less power consumedBased on environmental considerations, simplified packaging is used in order to reduce waste.In addition, the bag is made from polyethylene which produces no toxic gases even when burned.
Less resources used
CX-423/44
CX-441/443 CX-44CX-481/482
2.5 times the sensing capability!
Twice the sensing range!Twice the sensing range!
SUNX’s unique optical systems and specially designed electronic circuits provide stable sensing of even the minutest height difference and the thinnest transparent film.
Detecting a height difference of even as little as 0.4 mm 0.016 in possible (equivalent to one business card).
Refer to p.8 for details.
WastageLess resources used
Spot
Comparative ratio with 1 representing conventional SUNX sensors
m
CX-400CX-400
Conventional Conventional productproductConventional product
Great visibility approx. "2 mm "0.079 in high luminance spot
CX-423
m The difference in sensing rangebetween black non-glossy paper (lightness: 5) and white non-glossy paper
High
Less
High
High luminance
m As of April 2004 and based on research conducted by SUNX.
Highest performance in its class m
Easy to use high-level functions!
Easy to use high-level functions!
Smallest spot in its class
m As of April 2004 and based on research conducted by SUNX.
30 % increase in sensing range between black and whitem compared to the conventional products!
4Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
5
Interference prevention filter (Optional)
Out of position
Slit mask
CX-411
Detecting out of position tape feeder cassette
CX-411CX-411
Synchronizing sensor for image processing systems
CX-482
m
CX-411: 10 m 32.808 ft
CX-412: 15 m 49.213 ft
A long 5 m 16.404 ft sensing range is possible with the red LED type that is easy to align with the beam axis. Can be used for wide automatic door shutters.
For transparent object sensing
Thru-beam type
Retroreflective type
The longest in its class, it realizes a 15 m 49.213 ft long-distance sensing range.Remarkable penetrating power enables applications such as package content detection. (Note)
Strong infrared beamCX-412
Long sensing range of 5 m 16.404 ftCX-493
Built-in polarizing filters ensure stable sensing even on a mirror surface object.
Retroreflective type with polarizing filtersCX-491
With a level of performance ranked No.1 in the industrym, these sensors provide stable sensing.
Strong against extraneous light and noiseCX-491
The interference prevention function lets two sensors of any type to be mounted close together precisely.
Two sensors can be mounted close together
Because the light source is an infrared light, it is strong on dust and dirt compared to the red beam type.
Strong on dust and dirtCX-412
Two CX-411 sensors, with their red beam light source, can be installed close together by fitting an interference prevention filter.
Even the thru-beam type is strong on mutual interference
CX-411
The longest in its class
CX-493: 5 m 16.404 ftCX-491: 3 m 9.843 ft
CX-482: 2 m 6.562 ftCX-481: 0.5 m 1.640 ft
The longest in its class
m
m
m
Applications
Note: When sensing utilizing penetrating power, make sure to verify using the actual sensor.
m As of April 2004 and based on research conducted by SUNX.
The longest in its class m
The longest in its class
No.1 in the industry
m As of April 2004 and based on research conducted by SUNX.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
6
CX-481
CX-491CX-491
CX-423
CX-482CX-482
CX-491CX-491
CX-424
Great visibility approx. "2 mm "0.079 in high luminance spot
CX-423
CX-422: 800 mm 31.496 inCX-421: 300 mm 11.811 inCX-424: 100 mm 3.937 in
CX-423: 70 to 200 mm2.756 to 7.874 inNarrow-view type
Diffuse reflective type
Our unique optical system and transparent object sensing circuitry provide stable sensing of even thinner transparent objects than the conventional models.
Introducing the transparent object sensing type sensor
These sensors realize a high luminance red LED spot that provides bright visibility enabling the sensing position to be checked at a glance.Because it has the smallest spot in its class, approx. "2 mm "0.079 in, even the minutest object can be accurately detected.
Beam axis alignment made easy with a high luminance spot beam
CX-423
Because these sensors possess many variations depending on the sensing range, enables you to make optimal volume adjustment easily.
Reduction of volume adjustment labor
Transparent objects detectable with CX-48 (Typical examples)
Glass sheetCylindrical glassAcrylic boardStyrol (Floppy case)Food wrapping filmCigarette case filmVinyl sackPet bottle (500m#)
Sensing object Sensing object size (mm in)50 1.969 "50 "1.969 #50 #1.969 50 1.969 50 1.969 50 1.969 50 1.969 50 1.969 "66 "2.598
t0.7 t0.028t1.3 t0.051t1.0 t0.039t0.9 t0.035t10 !m t0.394 milt20 !m t0.787 milt30 !m t1.181 mil
The optimum condition is defined as the condition in which the sensitivity level is set such that the stability indicator just lights up when the object is absent.
Note:
Reflector setting range CX-481: 300 to 500 mm 11.811 to 19.685 in,CX-482: 1 to 2 m 3.281 to 6.562 ft
[with the RF-230 reflector at the optimum condition (Note)]Each object should pass across the beam at the center between the sensor and the reflector.
?: Length of cylindrical glasses t : Thickness of sensing object
Sensing plastic bottles stacked on pallets Sensing glossy white electric appliances
Detecting transparent film Passage confirmation of object on a conveyor belt
Small parts sensing
Passage confirmation on substrate conveyance equipment
m
CX-48
Applications
Applications
Twice the sensing range!
Smallest spot in its class
m As of April 2004 and based on research conducted by SUNX.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
7
Great visibility approx. "2 mm "0.079 in high luminance spot
CX-441
CX-442CX-444
CX-441CX-443
The longest in its class300 mm 11.811 in 100 mm 3.937 in
50 mm 1.969 in50 mm 1.969 in
Spot diameter "2 mm "0.079 in approx.
Spot diameter "6.5 mm "0.256 in approx.
0.4 mm
0.016 in
CX-443Spot diameter: "6.5 mm
"0.256 inapprox.
Detection of presence / absence of objectsIgnores minute holes and accurately detects objects.
CX-441Spot diameter: "2 mm
"0.079 inapprox.
[Positioning]Detects minute holes.
Smallest spot in its class
Adjustable range reflective type
m
m
m
Can sense differences as small as 0.4 mm 0.016 in, with hysteresis of 2 % or lessAn advanced optical system provides sensing performance that is approx. 2.5 times than conventional models. Even ultra-small differences of 0.4 mm 0.016 in can be detected accurately.
Not affected by color. The difference in sensing range between black and white is 1 % or less. (Note)
Both black and white objects can be sensed at the same distances. No adjuster control is needed, even when products of different colors are moving along the production line.
Select from 2 spot diameters as per the applicationWithin the choice of 50 mm 1.969 in sensing range sensors, we offer small approx. "2 mm "0.079 in spot type optimal for detecting minute object and large approx. "6.5 mm "0.256 in spot type capable of sensing object covered with holes and grooves.
High precision typeCX-441/443
These sensors realize a high luminance red spot that provides bright visibility. The sensing position can be checked at a glance. Because the CX-441 sensor has the smallest spot in its class, approx. "2 mm "0.079 in, even the minutest object can be accurately detected.
The bright spot makes beam axis alignment easyEquipped with a 5-turn adjuster so that even challenging range settings can be handled with ease.
Can be used for sensing minute differences
2.5 times thesensing capability!
30 % highersensing capability
Note:
1.5 times longer than before1.5 times longer than before
Height differences of as little as 0.4 mm 0.016 in can be detected at a setting distance of 20 mm 0.787 in The difference in sensing range between
black non-glossy paper (lightness: 5) and white non-glossy paper
m
Highest performance in its class
Smallest spot in its class
m As of April 2004 and based on research conducted by SUNX.
[ ]
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
8
Applications
Biscuit sensing Passage confirmation Small tablet sensingDetects minute objects unaffected by glossy background objects. Uses FGS function.
Stable sensing even for thin objects. Uses FGS function.
Not affected by color variations in objects and background objects. Uses BGS function.
For details on the operation of the BGS / FGS functions, refer to p.24, ‘PRECAUTIONS FOR PROPER USE’.
BGS / FGS functions make even the most challenging settings possible!
The BGS function is best suited for the following case The FGS function is best suited for the following case
When object and background are separatedBackground not present Background present
When object and background are close togetherWhen the object is glossy or uneven
The sensor judges that an object is present when light is received at position A of the light-receiving element (2-segment element). This is useful if the object and background are far apart. The distance adjustment method is the same as the conventional adjustment method for adjustable range reflective type sensors.
The sensor judges that an object is present when no light is received at position B of the light-receiving element (2-segment element). Accordingly, even objects that are glossy can be sensed. This is useful if the object and background are close together, or if the object being sensed is glossy.
BGS (Background suppression) function FGS (Foreground suppression) function
Not affected if the background color changes or someone passes behind the conveyor.
Unaffected by gloss, color or uneven surfaces when sensing objects present on a conveyor belt.
Conveyor Conveyor Conveyor
Light received at position A
Light is not received at position B, so a object is judged to be present
Light received at position B
A
Lens
Emitting element
Object present For glossy objectObject absent
ON ONOFF
B
OFF in this condition only ON in all other conditions
Setting distance
ObjectMoving objectin the back
ONOFF
Element B
Element A
Setting distance
BGS FGS
A conveyor or other back-ground must be present
CX-441
CX-442
CX-443
Bac
kgro
und
( )
Light received at element B, or light not received ( ) ( )Light received
at element A
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
9
CX-400
CX-424 CX-424-P
CX-421 CX-421-P
CX-422 CX-422-P
CX-411 CX-411-P
CX-412 CX-412-P
CX-491 CX-491-P
CX-493 CX-493-P
CX-481 CX-481-P
CX-482 CX-482-P
CX-441 CX-441-P
CX-443 CX-443-P
CX-444 CX-444-P
CX-442 CX-442-P
CX-423 CX-423-P
EmittingelementPNP outputNPN output
Model No.Appearance Sensing rangeType
Infrared LED
Infrared LED
Red LED
Red LED
Infrared LED
Red LED
Red LED
ORDER GUIDE
10 m 32.808 ft
15 m 49.213 ft
3 m 9.843 ft (Note 1)
5 m 16.404 ft (Note 1)
50 to 500 mm 1.969 to 19.685 in (Note 1)
0.1 to 2 m 0.328 to 6.562 in (Note 1)
100 mm 3.937 in (Note 2)
300 mm 11.811 in (Note 2)
800 mm 31.496 in (Note 2)
2 to 50 mm 0.079 to 1.969 in
70 to 200 mm 2.756 to 7.874 in (Note 2)
15 to 100 mm 0.591 to 3.937 in
20 to 300 mm 0.787 to 11.811 in
50 to 500 mm1.969 to 19.685 in
0.1 to 2 m0.328 to 6.562 ft
A
B 0.8 to 2 m2.625 to 6.562 ft
100 to 500 mm 3.937 to 19.685 in
CX-482CX-481
3 m9.843 ft
5 m16.404 ft
0.1 to 5 m 0.328 to 16.404 ft
0.1 to 3 m 0.328 to 9.843 ft
CX-493CX-491
Setting rangeof the reflector: B
Sensingobject
Sensingrange: A
Sensor Reflector
Thr
u-be
amD
iffus
e re
flect
ive
Adj
usta
ble
rang
e re
flect
ive
Long
sens
ingran
geLo
ng se
nsing
range
With
polar
izing
filters
Ret
rore
flect
ive
Narro
w-vie
wSm
all s
pot
For
tran
spar
ent
obje
ct s
ensi
ng
NOTE: Mounting bracket is not supplied with the sensor. Please select from the range of optional sensor mounting brackets.
The sensing range of the retroreflective type sensor is specified for the RF-230 reflector. The sensing range represents the actual sensing range of the sensor. The sensing ranges itemized in ‘A’ of the table below may vary depending on the shape of sensing object. Be sure to check the operation with the actual sensing object.
Notes: 1)
The sensing range of the diffuse reflective type sensor is specified for white non-glossy paper (200200 mm 7.8747.874 in) as the object.2)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
10
CX-400
For transparentobject sensing
CX-411
CX-491
CX-441
CX-412-PCX-412CX-411-P
CX-491-P
CX-441-P
CX-442CX-442-P
CX-411-C05
CX-491-C05CX-412-P-C05
CX-491-P-C05
CX-411-C5
CX-491-C5CX-412-P-C5
CX-491-P-C5
CX-411-Z
CX-491-Z
CX-441-Z
CX-412-P-Z
CX-491-P-Z
CX-441-P-Z
CX-442-ZCX-442-P-Z
CX-443-ZCX-443-P-ZCX-444-ZCX-444-P-Z
CX-443CX-443-PCX-444CX-444-P
CX-411-J
CX-491-JCX-412-P-J
CX-412-C05 CX-412-C5 CX-412-Z CX-412-JCX-411-P-C05 CX-411-P-C5 CX-411-P-Z CX-411-P-J
CX-491-P-J
ORDER GUIDE
0.5 m 1.640 ft / 5 m 16.404 ft cable length type, M8 plug-in connector type, M12 pigtailed type0.5 m 1.640 ft / 5 m 16.404 ft cable length type (standard: 2 m 6.562 ft), M8 plug-in connector type and M12 pigtailed type are available.
Package without reflector
• CN-24A-C2 • CN-24A-C5
• CN-22-C2, CN-22-C5CN-24-C2, CN-24-C5
• CN-24AL-C2 • CN-24AL-C5
300 mm11.811 in
"14 mm"0.551 in
"5 mm"0.197 in
NPN output type
PNP output type
NPN output type
PNP output type
NPN output type
PNP output type
NPN output type
PNP output type
NPN output type
PNP output type
NPN output type
PNP output type
NPN output type
PNP output type
NPN output type
PNP output type
NPN output type
PNP output type
NPN output type
PNP output type
NPN output type
PNP output type
NPN output type
PNP output type
NPN output type
PNP output type
NPN output type
PNP output type
CX-493CX-493-P
CX-493-C05CX-493-P-C05
CX-493-C5CX-493-P-C5
CX-493-ZCX-493-P-Z
CX-493-JCX-493-P-J
CX-481 CX-481-C05 CX-481-C5 CX-481-Z CX-481-JCX-481-P CX-481-P-C05 CX-481-P-C5 CX-481-P-Z CX-481-P-JCX-482 CX-482-C05 CX-482-C5 CX-482-Z CX-482-JCX-482-P CX-482-P-C05 CX-482-P-C5 CX-482-P-Z CX-482-P-JCX-424
CX-421CX-424-P
CX-421-P
CX-424-C05
CX-421-C05CX-424-P-C05
CX-421-P-C05
CX-424-C5
CX-421-C5CX-424-P-C5
CX-421-P-C5
CX-424-Z
CX-421-ZCX-424-P-Z
CX-421-P-Z
CX-424-J
CX-421-JCX-424-P-J
CX-421-P-JCX-422
CX-423CX-422-P
CX-423-P
CX-422-C05
CX-423-C05CX-422-P-C05
CX-423-P-C05
CX-422-C5
CX-423-C5CX-422-P-C5
CX-423-P-C5
CX-422-Z
CX-423-ZCX-422-P-Z
CX-423-P-Z
CX-422-J
CX-423-JCX-422-P-J
CX-423-P-J
23.1 mm0.909 in
"4 mm "0.157 in
"9 mm "0.354 in
20.5 mm0.807 in
31.4 mm1.236 in
"4 mm"0.157 in
"9 mm"0.354 in
Small spot
Adjustable rangereflective
NPN output type: CX-491-YPNP output type: CX-491-P-Y
Mating cables
Thru-beam
Retro-reflective
Diffuse reflective
Narrow-view
Long sensingrange
Long sensingrange
Type Output Standard 0.5 m 1.640 ft cablelength type
5 m 16.404 ft cablelength type
M8 plug-in connectortype (Note)
M12 pigtailedtype (Note)
With polarizingfilters
Note : Please order the suitable mating cable separately for M8 plug-in connector type and M12 pigtailed type.
CN-24A-C2
CN-24A-C5
CN-24AL-C2
CN-24AL-C5
2 m 6.562 ft
Can be used with all models
Can be used with all models
For thru-beam type emitter(2-core)
5 m 16.404 ft
2 m 6.562 ft
5 m 16.404 ft
CN-22-C2 2 m 6.562 ft
CN-22-C5 5 m 16.404 ft
CN-24-C2 2 m 6.562 ft
CN-24-C5 5 m 16.404 ft
• Mating cables (2 cables are required for the thru-beam type.)
For
M8
plug
-inco
nnec
tor
type
For
M12
pigt
aile
d ty
pe
Type
Straight
Elbow
2-core
4-core
Model No. Cable length Description
Accessory
RF-230 (Reflector)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
11
CX-400
OS-CX-05CX-411
CX-412
CX-411
CX-412
CX-411
CX-412
CX-411
CX-412
CX-411
CX-412
CX-411
CX-412
Round slit mask • OS-CX-
Fitted on the front face of the sensor withone-touch.
• OS-CX-6
• PF-CX4-V • PF-CX4-H
Rectangular slit mask
Interference prevention filter
Reflector • RF-210 • RF-220
Round slit mask(Stainless steel)
Rectangular slit mask(Stainless steel)
400 mm 15.748 in 20 mm 0.787 in"12 mm "0.472 in
"0.5 mm"0.020 in
OS-CX-1900 mm 35.433 in 100 mm 3.937 in
"12 mm "0.472 in"1 mm "0.039 in
OS-CX-22 m 6.562 ft 400 mm 15.748 in
"12 mm "0.472 in"2 mm "0.079 in
"1.5 mm "0.059 in
"3 mm "0.118 in
2 m 6.562 ft 400 mm 15.748 in"12 mm "0.472 in
0.56 mm0.0200.236 in
3 m 9.843 ft 1 m 3.281 ft"12 mm "0.472 in
16 mm0.0390.236 in
5 m 16.404 ft 2 m 6.562 ft
600 mm 23.622 in 30 mm 1.181 in
1.35 m 4.429 ft 150 mm 5.906 in
3 m 9.843 ft 600 mm 23.622 in
3 m 9.843 ft 600 mm 23.622 in
4.5 m 14.764 ft 1.5 m 4.921 ft
7.5 m 24.606 ft 3 m 9.843 ft"12 mm "0.472 in
26 mm0.0790.236 in
1 m 3.281 ft (Note 2)
1.5 m 4.921 ft (Note 2)
0.1 to 0.6 m 0.328 to 1.969 ft (Note 2)
1.5 m 4.921 ft (Note 2)
3 m 9.843 ft (Note 2)
50 to 300 mm 1.969 to 11.811 in (Note 2)
0.1 to 1.3 m 0.328 to 4.265 ft (Note 2)
CX-491
CX-493
CX-481
CX-482
CX-491
CX-493
CX-481
CX-482
"30 mm "1.181 in
"35 mm "1.378 in
Interference prevention filter
OPTIONS
OS-CX-056
OS-CX-16
OS-CX-26
RF-210
RF-220
DesignationModel No.
Slit size
Round slit maskFor thru-beamtype sensoronly
Slit on one sideSensorSlit Slit on both sides Slit on one side Slit on both sides
Sensing range Min. sensing object
( (
Rectangularslit maskFor thru-beamtype sensoronly( (
"0.5 mm"0.020 in
"1 mm"0.039 in
"2 mm"0.079 in
0.56 mm0.0200.236 in
16 mm0.0390.236 in
26 mm0.0790.236 in
PF-CX4-V(Vertical)
5 m 16.404 ft(Note 1)
"12 mm "0.472 in(Note 1)
PF-CX4-H(Horizonal)
5 m 16.404 ft(Note 1)
"12 mm "0.472 in(Note 1)
Designation Model No. Sensing range Min. sensing object
ReflectorFor retro-reflective typesensor only( (
Interferenceprevention filterFor CX-441 only( (
Notes: 1) 2)
Value when attached to both sides.Set the distance between the CX-491/493 and the reflector to 0.1 m 0.328 ft or more.However, see the table below for CX-48.The sensing range ‘A’ may vary depending on the shape of sensing object.Be sure to check the operation with the actual sensing object.
Fitted on the front face of the sensor withone-touch.
Two sets of CX-441 can be mounted close together.
33.3 mm1.311 in
11 mm0.433 in
12.8 mm0.504 in
35.3 mm1.390 in
8.3 mm0.327 in
42.3 mm1.665 in
CX-481
CX-482
RF-220
RF-220
RF-210
Model No.ReflectorSensor
BA
Setting rangeof the reflector: B
Sensingobject
Sensingrange: A
Sensor Reflector
100 to 300 mm3.937 to 11.811 in
0.5 to 1.3 m1.640 to 4.265 ft
50 to 300 mm1.969 to 11.811 in
0.1 to 1.3 m0.328 to 4.265 ft
0.3 to 0.6 m0.984 to 1.969 ft
0.1 to 0.6 m0.328 to 1.969 ft
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
12
CX-400
• Sensing range (Note 4):0.5 m 1.640 ft [CX-491]0.8 m 2.625 ft [CX-493]
• Sensing range (Note 4):0.7 m 2.297 ft [CX-491]1.2 m 3.937 ft [CX-493]0.1 to 0.6 m 0.328 to 1.969 ft [CX-482]
• Sensing range (Note 4):0.5 m 1.640 ft [CX-491]0.8 m 2.625 ft [CX-493]
• Ambient temperature: 25 to 55 C13 to 131 F
• Ambient humidity: 35 to 85 % RH
RF-11
RF-12
RF-13
Universal sensormounting stand(Note 2)
MS-CX2-1
MS-CX2-2
MS-CX2-4
MS-CX2-5
MS-CX-3
MS-AJ1MS-AJ2MS-AJ1-AMS-AJ2-AMS-AJ1-M
Sensor mounting bracket • MS-CX2-2
• MS-CX2-4
• MS-RF22
Reflector mounting bracket
• MS-RF23
Two M3 (length 14 mm 0.551 in) screws with washers are attached.
Two M3 (length 12 mm 0.472 in) screws with washers are attached.
• MS-RF21-1
• MS-CX2-1
• CHX-SC2
Two M3 (length 12 mm 0.472 in) screws with washers are attached.
• MS-CX2-5
Two M3 (length 12 mm 0.472 in) screws with washers are attached.
• MS-CX-3
Two M3 (length 12 mm 0.472 in)screws with washers are attached.
MS-RF21-1
MS-RF22
MS-RF23
Reflective tape • RF-11 • RF-12
Sensor checker
MS-AJ2-M
CHX-SC2
Universal sensor mounting stand
• MS-AJ1 • MS-AJ1-A
Angle adjustment: 45
Swivel: 360 rotation
Elevationangle: 45
Swivel: 360 rotation
Mounting hole for M6 screw
Mounting hole forM6 screw
• MS-AJ2 • MS-AJ2-A
Elevationangle: 45
Mounting hole for M6 screw
Swivel: 360 rotation
Angle adjustment: 45
Swivel: 360 rotation
Mounting hole for M6 screw
• RF-13
Swivel: 360 rotation
Elevationangle: 45
Height adjustment:150 mm 5.906 in approx.
Mounting hole for M6 screw
• MS-AJ1-M
OPTIONS
Height adjustment:150 mm 5.906 in approx.
Mounting hole for M6 screw
Swivel: 360 rotation
• MS-AJ2-M
30 mm1.181 in
30 mm1.181 in
0.5 mm0.020 in
LEVEL
POWER CHX-SC2
Sensor checker
Designation Model No. Description
Reflectormountingbracket
Reflective tape
Sensormountingbracket(Note 1)
Sensor checker(Note 3)
• Ambient temperature:25 to 50 C13 to 122 F
• Ambient humidity:35 to 85 % RH
For RF-220
For RF-230
Foot angled mounting bracketIt can also be used for mounting RF-210.
Foot biangled mounting bracketIt can also be used for mounting RF-210.
Protective mounting bracket
Back biangled mounting bracket
Back angled mounting bracket
The thru-beam type sensor needs two brackets.
Protective mounting bracket for RF-210It protects the reflector from damage and maintains alignment.
Keep the tape free from stress. If it is pressed too much, its capability may deteriorate.Do not cut the tape. It will deteriorate the sensing performance.
Notes: 1)
2)
Horizontal mounting type
Vertical mounting type
Horizontal mounting type
Vertical mounting type
Horizontal mounting type
Vertical mounting type
Basic assembly
Lateral arm assembly
Assembly for reflector
It is useful for beam alignment of thru-beam type sensors. The optimum receiver position is given by indicators, as well as an audio signal.
The plug-in connector type sensor does not allow use of some sensor mounting brackets because of the protrusion of the connector.Refer to the Sensor general catalog 2003-2004 for details of the universal sensor mounting stand.Refer to the Sensor general catalog 2003-2004 for details of the sensor checker CHX-SC2.Set the distance between the sensor and the reflective tape to 0.1 m 0.328 ft (CX-482: 0.4 m 1.312 ft) or more.
Notes: 1)
2) 3) 4)
30 mm1.181 in
0.7 mm0.028 in
8 mm0.315 in
30 mm1.181 in
25 mm0.984 in
0.7 mm0.028 in
Two M4 (length 10 mm 0.394 in) screws with washers are attached.
Two M3 (length 8 mm 0.315 in) screws with washers are attached.
45
45
45
45
Height adjustment:150 mm 5.906 in approx.
45
45
45
45Elevationangle: 45
360
4545
With the lateral arm, the sensor can sense from above a production line.
rotation
360
4545
With the lateral arm, the sensor can sense from above a production line.
rotation
Two M3 (length 12 mm 0.472 in) screws with washers are attached.
Height adjustment:150 mm 5.906 in approx.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
13
CX-400
SPECIFICATIONS
70 to 200 mm 2.756 to 7.874 in (Note 2)
800 mm 31.496 in (Note 2)
100 mm 3.937 in (Note 2)
300 mm11.811 in (Note 2)
3 m 9.843 ft (Note 1)
5 m 16.404 ft (Note 1)
0.1 to 2 m 0.328 to 6.562 ft (Note 1)
50 to 500 mm1.969 to 19.685 in (Note 1)
10 m 32.808 ft
15 m 49.213 ft
CX-423
Opaque, translucent or transparent object
"50 mm "1.969 in or more transparent, translucent oropaque object (Note 1)
"12 mm "0.472 in or more opaque object (Note 3)
15 % or less of operation distance
1 mm 0.039 in or less 0.5 mm 0.020 in or less0.5 mm 0.020 in or less
12 to 24 V DC10 % Ripple P-P 10 % or less
25 mA or less20 mA or less 25 mA or less 20 mA or lessEmitter: 20 mA or lessReceiver: 20 mA or less
Emitter: 25 mA or lessReceiver: 20 mA or less
Infrared LED Red LEDRed LED Red LEDInfrared LED
Narrow-view
CX-422
Diffuse reflectiveLong sensing rangeLong sensing range For transparent object sensing
CX-421
Retroreflective
CX-411
CX-423-PCX-422-PCX-421-P
CX-424
CX-424-P
CX-493
CX-493-P
CX-481 CX-482
CX-481-P CX-482-PCX-411-P
CX-412
CX-412-P
Thru-beam
CX-491
With polarizing filters
CX-491-P
Opaque, translucent or transparent object
( Min. sensing object: "0.5 mm "0.020 in copper wire )
50 to 500 mm1.969 to 19.685 in
0.1 to 2 m0.328 to 6.562 ft
A
B0.8 to 2 m2.625 to 6.562 ft
100 to 500 mm3.937 to 19.685 in
CX-482CX-481
3 m 9.843 ft 5 m16.404 ft
0.1 to 5 m0.328 to 16.404 ft
0.1 to 3 m0.328 to 9.843 ft
CX-493CX-491
Setting rangeof the reflector: B
Sensingobject
Sensingrange: A
Sensing range
Sensing object
Hysteresis
Repeatability (perpendicular to sensing axis)
Supply voltage
Current consumption
Output
Output operation
Short-circuit protection
Response time
Emitting element (modulated)
Power indicator
Operation indicator
Stability indicator
Sensitivity adjuster
Automatic interferenceprevention function
Protection
Ambient temperature
Ambient humidity
Ambient illuminance
EMC
Voltage withstandability
Insulation resistance
Vibration resistance
Material
Cable
Cable extension
Weight
Accessories
Shock resistance
Item
Type
NPN output
PNP output
Env
ironm
enta
l res
ista
nce
Mod
el No
.
"50 mm "1.969 in or more opaque, translucent or specular object (Note 1)
"50 mm "1.969 in or more opaque or translucent object (Note 1)
RF-230 (Reflector): 1 pc.
Switchable either Light-ON or Dark-ON
Incorporated
1 ms or less
Orange LED (lights up when the output is ON)(incorporated on the receiver for thru-beam type)
Green LED (lights up under stable light received condition or stable dark condition)(incorporated on the receiver for thru-beam type)
Continuously variable adjuster (incorporated on the receiver for thru-beam type)
Incorporated (Two units of sensors can be mounted close together.)
IP67 (IEC)
25 to 55 C 13 to 131 F (No dew condensation or icing allowed ), Storage: 30 to 70 C 22 to 158 F
35 to 85 % RH, Storage: 35 to 85 % RH
Sunlight:10,000 ?x at the light-receiving face, Incandescent light: 3,000 ?x at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude (10 G max.) in X, Y and Z directions for two hours each
Enclosure: PBT (polybutylene terephthalate), Lens: acrylic (CX-48: polycarbonate), Front cover: acrylic (CX-48: polycarbonate)
0.2 mm2 3-core (thru-beam type emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable (thru-beam type: both emitter and receiver)
50 g approx. (Emitter of thru-beam type: 45 g approx.)
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
<NPN output type> NPN open-collector transistor
• Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between output and 0 V)• Residual voltage: 1 V or less (at 100 mA sink current)
0.4 V or less (at 16 mA sink current)
<PNP output type> PNP open-collector transistor
• Maximum source current: 100 mA• Applied voltage: 30 V DC or less (between output and V)• Residual voltage: 1 V or less (at 100 mA source current)
0.4 V or less (at 16 mA source current)
Green LED (lights up when the power is ON) (incorporated on the emitter)
Two units of sensors can be mounted close together with interference prevention filters. (Sensing range: 5 m 16.404 ft)
Sensor Reflector
The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-230 reflector. The sensing range represents the actual sensing range of the sensor. The sensing ranges itemized in ‘A’ of the table below may vary depending on the shape of sensing object. Be sure to check the operation with the actual sensing object.
Notes: 1)
The sensing range of the diffuse reflective type sensor is specified for white non-glossy paper (200 200 mm 7.874 7.874 in) as the object.If slit masks (optional) are fitted, an object of "0.5 mm "0.020 in (using round slit mask) can be detected.
2) 3)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
14
CX-400
20 to 50 mm 0.787 to 1.969 in
2 to 50 mm 0.079 to 1.969 in
CX-441 CX-444
Small spot
CX-442CX-443
CX-441-P CX-444-P CX-442-PCX-443-P
Adjustable range reflective
SPECIFICATIONS
Actual sensing range of the sensor: A
20 to 100 mm 0.787 to 3.937 in
15 to 100 mm 0.591 to 3.937 in
5 % or less of operation distance
40 to 300 mm 1.575 to 11.811 in
20 to 300 mm 0.787 to 11.811 in
2 % or less of operation distance
20 to 300 mm0.787 to 11.811 inA
B40 to 300 mm1.575 to 11.811 in
CX-442
2 to 50 mm0.079 to 1.969 in
20 to 50 mm0.787 to 1.969 in
15 to 100 mm0.591 to 3.937 in
20 to 100 mm0.787 to 3.937 in
CX-444 CX-441/443
Item
Type
NPN output
PNP outputMod
el No
.
Env
ironm
enta
l res
ista
nce
Adjustable range (Note 1)
Sensing range (with white non-glossy paper)
Hysteresis
Repeatability
Supply voltage
Current consumption
Response time
Operation indicator
Stability indicator
Distance adjuster
Sensing mode
Automatic interference prevention function (Note 3)
Output
Emitting element
Spot diameter
Material
Cable
Cable extension
Weight
Protection
Ambient temperature
Ambient humidity
Ambient illuminance
EMC
Voltage withstandability
Insulation resistance
Vibration resistance
Shock resistance
Output operation
Short-circuit protection
Switchable either Detection-ON or Detection-OFF
Incorporated
1 ms or less
Orange LED (lights up when the output is ON)
Green LED (lights up under stable operating condition) (Note 2)
5-turn mechanical adjuster
BGS / FGS functions Switchable with wiring of sensing mode selection input
Incorporated
IP67 (IEC)
25 to 55 C 13 to 131 F (No dew condensation or icing allowed ), Storage: 30 to 70 C 22 to 158 F
35 to 85 % RH, Storage: 35 to 85 % RH
Sunlight:10,000 ?x at the light-receiving face, Incandescent light: 3,000 ?x at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in double amplitude in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (modulated)
Enclosure: PBT (Polybutylene terephthalate), Front cover: Polycarbonate, Indicator cover: Polycarbonate
0.2 mm2 4-core cabtyre cable, 2 m 6.562 ft long
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
55 g approx.
Along sensing axis: 1 mm 0.039 in or less, Perpendicular to sensing axis: 0.2 mm 0.008 in or less (with white non-glossy paper)
12 to 24 V DC10 % Ripple P-P 10 % or less
25 mA or less
"2 mm "0.079 in approx. (at 50 mm 1.969 in distance)
"6.5 mm "0.256 in approx. (at 50 mm 1.969 in distance)
"9 mm "0.354 in approx. (at 100 mm 3.937 in distance)
15 mm 0.591 in approx. (at 300 mm 11.811 in distance)
Sensingobject
Adjustable range: B
The adjustable range stands for the maximum sensing range which can be set with the distance adjuster. The sensor can detect an object 2 mm 0.079 in [CX-444(-P): 15 mm 0.591 in, CX-442(-P): 20 mm 0.787 in], or more, away.Refer to ‘Stability indicator’ (p.24) of ‘PRECAUTIONS FOR PROPER USE’ for the details of operation indicator.Note that detection may be unstable depending on the mounting conditions or the sensing object. In the state that this product is mounted, be sure to check the operation with the actual sensing object.
Notes: 1)
2)
3)
<NPN output type> NPN open-collector transistor
• Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between output and 0 V)• Residual voltage: 1 V or less (at 100 mA sink current)
0.4 V or less (at 16 mA sink current)
<PNP output type> PNP open-collector transistor
• Maximum source current: 100 mA• Applied voltage: 30 V DC or less (between output and V)• Residual voltage: 1 V or less (at 100 mA source current)
0.4 V or less (at 16 mA source current)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
15
CX-400
I/O CIRCUIT AND WIRING DIAGRAMS
NPN output type
Wiring diagram
Wiring diagram
Connector pin position
PNP output type
Connector pin position
D
Tr
ZD
I/O circuit diagram
Tr ZD
D
I/O circuit diagram
m1
Users’ circuitInternal circuit
100 mA max.
(Pink / 2) Sensing mode selection input (Note 2)
(Blue / 3) 0 V
12 to 24 V DC10 %
(Brown / 1) V
(Black / 4)Output (Note 1)
Load
Sen
sor
circ
uit
Color code / Connector pin No. of the plug-in connector type
Notes: 1)
2)
The emitter of the thru-beam type sensor does not incorporate the output.Sensing mode selection input is incorporated only for the CX-44 adjustable range reflective type. When using the CX-44, be sure to wire the sensing mode selection input (pink / 2).
Notes: 1)
2)
The emitter of the thru-beam type sensor does not incorporate the output.Sensing mode selection input is incorporated only for the CX-44-P adjustable range reflective type. When using the CX-44-P, be sure to wire the sensing mode selection input (pink / 2).
m1
• Sensing mode selection inputBGS function: Connect to 0 VFGS function: Connect to V
Symbols ... D ZD
Tr
: Reverse supply polarity protection diode: Surge absorption zener diode: NPN output transistor
m1
Load
Brown
Black (Note 1)
Blue
Pink (Note 2)
12 to 24 V DC10 %
The emitter of the thru-beam type sensor does not incorporate the black wire.The pink wire is incorporated only for the CX-44 adjustable range reflective type. When using the CX-44, be sure to wire the pink wire.
Notes: 1) 2)
m1
• Sensing mode selection inputBGS function: Connect to 0 VFGS function: Connect to V
2Sensing modeselection input
(Note 2)
2Not
connected
4Output
(Note 1)
1 V
1 V
30 V
30 V
4Output (Note 1)
M8 plug-in connector type M12 pigtailed type
The emitter of the thru-beam type sensor does not incorporate the output.Sensing mode selection input is incorporated only for the CX-44 adjustable range reflective type. When using the CX-44, be sure to wire the sensing mode selection input (pink / 2).
Notes: 1) 2)
m1
Users’ circuitInternal circuit
100 mA max.
(Pink / 2) Sensing mode selection input (Note 2)
(Blue / 3) 0 V
12 to 24 V DC10 %
(Brown / 1) V
(Black / 4) Output (Note 1)Load
Sen
sor
circ
uit
Color code / Connector pin No. of the plug-in connector type
m1
• Sensing mode selection inputBGS function: Connect to 0 VFGS function: Connect to V
Symbols ... D ZD
Tr
: Reverse supply polarity protection diode: Surge absorption zener diode: PNP output transistor
m1
Load
Brown
Black (Note 1)
Blue
Pink (Note 2)
12 to 24 V DC10 %
Notes: 1) 2)
The emitter of the thru-beam type sensor does not incorporate the black wire.The pink wire is incorporated only for the CX-44-P adjustable range reflective type. When using the CX-44-P, be sure to wire the pink wire.
m1
• Sensing mode selection inputBGS function: Connect to 0 VFGS function: Connect to V
2Sensing modeselection input
(Note 2)
2Not
connected
4 Output (Note 1)
1 V
1 V
30 V
30 V
4 Output (Note 1)
M8 plug-in connector type M12 pigtailed type
The emitter of the thru-beam type sensor does not incorporate the output.Sensing mode selection input is incorporated only for the CX-44-P adjustable range reflective type. When using the CX-44-P, be sure to wire the sensing mode selection input (pink / 2).
Notes: 1) T2)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
16
CX-400
CX-412
CX-411
#
$
#
$
##
###
##
##
# #
#
##
##
##
Parallel deviation
Thru-beam type
Angular deviation
200 0 200 40040015.748 7.874 7.874 15.748
0
516.404
1032.808
Left RightCenterOperating point ?(mm in)
Set
ting
dist
ance
L (
m ft
)
L
Emitter
Receiver
400
516.404
1032.808
Set
ting
dist
ance
L (
m ft
)
20 0 20 40
L
Receiver
Left RightCenterOperating angle $( ° )
Emitter
400
Set
ting
dist
ance
L (
m ft
)
20 0 20 40
L
Receiver
Left RightCenterOperating angle $( ° )
Emitter
L
Receiver
EmitterSlit onboth sides
00.787 0.394 0.394 0.787
0
2007.874
40015.748
Parallel deviation with roundslit masks ("0.5 mm "0.020 in)
Left RightCenterOperating point ?(mm in)
Set
ting
dist
ance
L (
mm
in)
10 10 20
Slit onone side
20
40015.748
80031.496
Parallel deviation with roundslit masks ("1 mm "0.039 in)
Set
ting
dist
ance
L (
mm
in)
Receiver
Emitter
Slit onone side
Slit onboth sides
L
40 20 00
20 401.575 0.787 0.787 1.575
Left RightCenterOperating point ?(mm in)
0
13.281
26.562
39.843
413.123
0
13.281
26.562
39.843
413.123
Parallel deviation with roundslit masks ("2 mm "0.079 in)
Set
ting
dist
ance
L (
m ft
)
Slit onone side
Slit onboth sides
Receiver
Emitter
L
400 200 0 200 40015.748 7.874 7.874 15.748
400 200 0 200 40015.748 7.874 7.874 15.748
400 200 0 200 40015.748 7.874 7.874 15.748
Left RightCenterOperating point ?(mm in)
Parallel deviation with rectangularslit masks (0.56 mm 0.0200.236 in)
Set
ting
dist
ance
L (
m ft
)
CenterOperating point ?(mm in)
(Down) Left Right (Up)
Horizontaldirection
Verticaldirection
Receiver Receiver
Emitter Emitter
Slit on one side Horizontal direction
Slit on one side Vertical direction
Slit on both sides Horizontal and Vertical direction
Slit on both sides Horizontal and Vertical direction
Slit on both sides Horizontal and Vertical direction
LL
Parallel deviation with rectangular slit masks (16 mm 0.0390.236 in)
CenterOperating point ?(mm in)
(Down) Left Right (Up)
26.562
413.123
Emitter Emitter
Horizontaldirection
Verticaldirection
Horizontaldirection
Verticaldirection
0Receiver
LL
Receiver
Set
ting
dist
ance
L (
m ft
) 619.685
826.247
Parallel deviation with rectangular slit masks (26 mm 0.0790.236 in)
Set
ting
dist
ance
L (
m ft
)
80031.496
400 400 80015.748 15.748 31.496
L
Receiver
Emitter
CenterOperating point ?(mm in)
(Down) Left Right (Up)
26.562
413.123
Emitter
L
Receiver
00
Set
ting
dist
ance
L (
m ft
)
Parallel deviation
Thru-beam type
Angular deviation
500 0 500 1,0001,00039.370 19.685 19.685 39.370
0
516.404
1032.808
1549.213
2065.617
516.404
1032.808
1549.213
2065.617
Left RightCenterOperating point ?(mm in)
Set
ting
dist
ance
L (
m ft
)
L
Emitter
Receiver
L
Receiver
Emitter
Slit onboth sides
03.937 1.969 1.969 3.937
0
2007.874
40015.748
60023.622
80031.496
0
0.51.640
13.281
1.54.921
26.562
Parallel deviation with roundslit masks ("0.5 mm "0.020 in)
Left RightCenterOperating point ?(mm in)
Set
ting
dist
ance
L (
mm
in)
50 50 100
Slit onone side
100
Parallel deviation with roundslit masks ("1 mm "0.039 in)
Receiver
Emitter
Slit onone side
Slit onboth sides
L
200 100 0 100 2007.874 3.937 3.937 7.874
Left RightCenterOperating point ?(mm in)
0
13.281
26.562
Parallel deviation with roundslit masks ("2 mm "0.079 in)
Set
ting
dist
ance
L (
m ft
)
Slit onone side
Slit onboth sides
Receiver
Emitter
L
100 50 0 50 1003.937 1.969 1.969 3.937
Left RightCenterOperating point ?(mm in)
Parallel deviation with rectangularslit masks (0.56 mm 0.0200.236 in)
100 50 50 1003.937 1.969 1.969 3.937
13.281
26.562
Set
ting
dist
ance
L (
m ft
)
CenterOperating point ?(mm in)
(Down) Left Right (Up)
Slit onboth sidesHorizontaldirection
Horizontaldirection
Verticaldirection
Receiver Receiver
Emitter Emitter
Slit on one side Vertical direction
Slit on one side Horizontal direction
Slit onboth sidesVerticaldirection
LL
00
Parallel deviation with rectangular slit masks (16 mm 0.0390.236 in)
Slit on both sidesHorizontal direction
Slit on one side Horizontal direction
Slit on one side Vertical direction
CenterOperating point ?(mm in)
(Down) Left Right (Up)
07.874 3.937 7.874
26.562
39.843
413.123
Emitter Emitter
Horizontaldirection
VerticaldirectionSlit on both sides
Vertical direction
200 2003.937
0
13.281
Receiver
LL
Receiver
Set
ting
dist
ance
L (
m ft
)
100 100
619.685
826.247
Parallel deviation with rectangular slit masks (26 mm 0.0790.236 in)
Set
ting
dist
ance
L (
m ft
)
Slit on one side Horizontal direction
Slit on one side Vertical direction
2007.874
100 100 2003.937 3.937 7.874
L
Receiver
Emitter
Verticaldirection
CenterOperating point ?(mm in)
(Down) Left Right (Up)
Slit on both sides Vertical direction
26.562
413.123
Emitter
L
Horizontaldirection Slit on both sides
Horizontal direction
Receiver
00
SENSING CHARACTERISTICS (TYPICAL)
Slit on one side Horizontal direction
Slit on one side Vertical direction
Slit on one side Vertical direction
Slit on one side Horizontal direction
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
17
CX-400
SENSING CHARACTERISTICS (TYPICAL)
CX-493
CX-421
CX-424
CX-491
CX-482CX-481
# $
$
#
$
$
# #
$$
$
$
#
#
200 100 0 100 2007.874 3.937 3.937 7.874
200 100 0 100 2007.874 3.937 3.937 7.874
200 100 0 100 2007.874 3.937 3.937 7.874
100 50 0 50 1003.937 1.969 1.969 3.937
40 20 0 20 40
Left CenterOperating point ?(mm in)
Set
ting
dist
ance
L (
m ft
)
13.281
26.562
39.843
413.123
13.281
26.562
39.843
413.123
Sensor
Reflector (RF-230)
Left RightCenterOperating angle $( ° )
L
Sensor
Reflector (RF-230)
L
Sensor
L
Sensor
Reflector (RF-230)
L
Sensor
Reflector (RF-230)
L
L
0
26.562
413.123
13.281
26.562
619.685
826.247
0
13.281
26.562
0
26.562
413.123
619.685
826.247
00
Set
ting
dist
ance
L (
m ft
)
Sensor
Sensor SensorSensor
0
2007.874
40015.748
60023.622
80031.496
0
2007.874
40015.748
60023.622
80031.496
0
Right
Parallel deviation Angular deviation
Retroreflective type
Parallel deviation Angular deviation
Retroreflective type
Parallel deviation Angular deviation
Retroreflective type
Parallel deviation Angular deviation
Retroreflective type
Reflector (RF-230)
Reflector (RF-230)
Sensorangulardeviation
Reflectorangulardeviation
Sensorangulardeviation
Reflectorangulardeviation
Sensorangular
deviation
L
Sensor
Reflector (RF-230)
Sensorangular
deviation
Reflectorangulardeviation
40 20 0 20 40
Left CenterOperating point ?(mm in)
Left RightCenterOperating angle $( ° )Right
40 20 0 20 40
Left CenterOperating point ?(mm in)
Set
ting
dist
ance
L (
m ft
)
Left RightCenterOperating angle $( ° )
Set
ting
dist
ance
L (
m ft
)
Right
40 20 0 20 40
Left CenterOperating point ?(mm in)
Set
ting
dist
ance
L (
m ft
)
Left RightCenterOperating angle $( ° )
Set
ting
dist
ance
L (
m ft
)
Right
Set
ting
dist
ance
L (
mm
in)
Set
ting
dist
ance
L (
mm
in)
L
Reflectorangulardeviation
Sensorangulardeviation
Reflector angulardeviationReflector(RF-230)
Sensor angulardeviation
LLReflector(RF-230)
Reflector(RF-230)
Reflectorangulardeviation
Sensorangular
deviation
L
Reflector (RF-230) Reflector (RF-230)
Sensorangular
deviationReflectorangulardeviation
LL
Sensor Sensor
Sensorangulardeviation
Reflectorangulardeviation
Diffuse reflective type
Sensing field Correlation between sensing object size and sensing range
As the sensing object size becomes smaller than the standard size (white non-glossy paper 200200 mm 7.8747.874 in), the sensing range shortens, as shown in the left graph.
For plotting the left graph, the sensitivity has been set such that a 200200 mm 7.8747.874 in white non-glossy paper is just detectable at a distance of 100 mm 3.937 in.
( )20 10 0 10 20
0
501.969
0.787 0.394 0.394 0.787
1003.937
Set
ting
dist
ance
L (
mm
in)
0
L
Sensor
200200 mm7.8747.874 inWhite non-glossy paper
50 100 150 2001.969 3.937 5.906 7.874
Sen
sing
ran
ge L
(m
m in
)
Sensor
aa mm White non-glossy paper
L
Left RightCenterOperating point ?(mm in)
White non-glossy paper side length a (mm in)
501.969
1003.937
Diffuse reflective type
Sensing field Correlation between sensing object size and sensing range
40 20 0 20 400
1003.937
2007.874
40015.748
1.575 0.787 0.787 1.575
30011.811
Set
ting
dist
ance
L (
mm
in)
Left RightCenterOperating point ?(mm in)
0
1003.937
2007.874
30011.811
40015.748
L
Sensor
200200 mm7.8747.874 inWhite non-glossy paper
50 100 150 2001.969 3.937 5.906 7.874White non-glossy paper side length a (mm in)
Sensor
aa mm White non-glossy paper
L
As the sensing object size becomes smaller than the standard size (white non-glossy paper 200200 mm 7.8747.874 in), the sensing range shortens, as shown in the left graph.
For plotting the left graph, the sensitivity has been set such that a 200200 mm 7.8747.874 in white non-glossy paper is just detectable at a distance of 300 mm 11.811 in.
( )
Sen
sing
ran
ge L
(m
m in
)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
18
CX-400
CX-423
CX-422
#
#
Diffuse reflective type
Sensing field Correlation between sensing object size and sensing range
40 20 0 20 401.575 0.787 0.787 1.575
50019.685
1,00039.370
01.969 3.937
40015.748
80031.496
Set
ting
dist
ance
L (
mm
in)
Left RightCenterOperating point ?(mm in)
Sensor
200200 mm7.8747.874 inWhite non-glossy paper
White non-glossy paper side length a (mm in)
L
50 100 150 2005.906 7.874
aa mm White non-glossy paper
L
As the sensing object size becomes smaller than the standard size (white non-glossy paper 200200 mm 7.8747.874 in), the sensing range shortens, as shown in the left graph.
For plotting the left graph, the sensitivity has been set such that a 200200 mm 7.8747.874 in white non-glossy paper is just detectable at a distance of 800 mm 31.496 in.
)(0
Sensor
N6
White
0.079 0.039 0.039 0.079
Diffuse reflective type
Sensing field Correlation between sensing object size and sensing range
2 1 0 1 20
1003.937
2007.874
N6
White
0
1003.937
2007.874
Set
ting
dist
ance
L (
mm
in)
Left RightCenterOperating point ?(mm in)
200200 mm7.8747.874 inNon-glossy paper
1.969 3.937
SensorL
aa mmNon-glossy paper
Non-glossy paper side length a (mm in)
5.906 7.87450 100 150 200
L
Sensor
As the sensing object size becomes smaller than the standard size (white non-glossy paper 200200 mm 7.8747.874 in), the sensing range shortens, as shown in the left graph.
For plotting the left graph, the sensitivity has been set such that a 200200 mm 7.8747.874 in white non-glossy paper is just detectable at a distance of 200 mm 7.874 in.
)(
Emitted beam2509.843
2007.8741505.906
501.969
0
1003.937
1104.331
"5 mm"0.197 in
"2.5 mm"0.098 in
"2.2 mm"0.087 in
"2 mm"0.079 in
"4 mm"0.157 in
Dis
tanc
e L
(mm
in)
Vis
ible
spo
t ran
ge
The sensing region is represented by oblique lines in the left figure. However, the sensitivity should be set with an enough margin because of slight variation in products.
Lightness shown on the left may differ slightly from the actual object condition.
( )
Correlation between lightness and sensing range
N2 N4 N8N6
1003.937
2007.874
N2 N5 N7 N9N1 N4 N6 N8N3
Sensingregion
Sen
sing
ran
ge L
(m
m in
)
Dark Light
0
Lightness
SENSING CHARACTERISTICS (TYPICAL)
Sen
sing
ran
ge L
(m
m in
)S
ensi
ng r
ange
L (
mm
in)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
19
CX-400
CX-443
SENSING CHARACTERISTICS (TYPICAL)
CX-441
# #
# #
• Setting distance: 50 mm 1.969 inEmitted beam
20.079
0 20.079
40.157
Black non-glossy paperLightness: 5
40.157
20.079
0 20.079
40.157
0
401.575
200.787
803.150
602.362
5050 mm 1.9691.969 inNon-glossy paper
Adjustable range reflective type
Adjustable range reflective type
Sensing fields• Setting distance: 25 mm 0.984 in
RightCenterOperating point ?(mm in)
Left RightCenterOperating point ?(mm in)
Black non-glossy paperLightness: 5
White non-glossy paper White non-
glossy paper
White non-glossy paper
These bars indicate the sensing range with the respec-tive colors when the distance adjuster is set to a sensing range of 50 mm 1.969 in and 25 mm 0.984 in long, respectively, with white color.The sensing range also varies depending on material.
Correlation between material (5050 mm 1.9691.969 in) and sensing range
Correlation between color(5050 mm 1.9691.969 in construction paper) and sensing range
200.787
401.575
602.362
301.181
501.969
803.150
0
"2 mm 0.079 in
"3 mm 0.118 in
"3 mm 0.118 in
40.157
0
100.394
200.787
301.181
401.575
Sensor
5050 mm 1.9691.969 inNon-glossy paper
L
Black non-glossy paperLightness: 5
Sensor
5050 mm 1.9691.969 inNon-glossy paper
L
Sensor
L
5050 mm 1.9691.969 inNon-glossy paper
Black non-glossy paperLightness: 5
White non-glossy paper
Sensor
L
501.969
501.969
"2 mm 0.079 in
Left
These bars indicate the sensing range with the re- spective objects when the distance adjuster is set to a sensing range of 50 mm 1.969 in and 25 mm 0.984 in long, respectively, with white non-glossy paper.0
250.984
Whi
te n
on-
glos
sy p
aper
Car
dboa
rd
Ply
woo
d
Bla
ck ru
bber
Black
non-g
lossy
pa
per (
Lightn
ess:
5)
250.984 50 mm
1.969 in25 mm0.984 in
0
Whi
te
Yel
low
Ora
nge
Bro
wn
Gre
en
Bla
ck
Red
Blu
e
Gra
y
Set
ting
dist
ance
L (
mm
in)
Set
ting
dist
ance
L (
mm
in)
Dis
tanc
e L
(mm
in)
50 mm1.969 in25 mm0.984 in
Sen
sing
ran
ge L
(m
m in
)
Sen
sing
ran
ge L
(m
m in
)
• Setting distance: 50 mm 1.969 inEmitted beam
20.079
0 20.079
40.157
40.157
20.079
0 20.079
40.157
0
401.575
200.787
803.150
602.362
Sensing fields• Setting distance: 25 mm 0.984 in
RightCenterOperating point ?(mm in)
Left RightCenterOperating point ?(mm in)
These bars indicate the sensing range with the respec-tive colors when the distance adjuster is set to a sensing range of 50 mm 1.969 in and 25 mm 0.984 in long, respectively, with white color.The sensing range also varies depending on material.
Correlation between material (5050 mm 1.9691.969 in) and sensing range
Correlation between color(5050 mm 1.9691.969 in construction paper) and sensing range
200.787
401.575
602.362
301.181
501.969
803.150
0
"6.2 mm 0.244 in
"5.9 mm 0.232 in
"5.3 mm 0.209 in
40.157
0
100.394
200.787
301.181
401.575
501.969
501.969
"6.5 mm 0.256 in
Left
These bars indicate the sensing range with the re- spective objects when the distance adjuster is set to a sensing range of 50 mm 1.969 in and 25 mm 0.984 in long, respectively, with white non-glossy paper.0
250.984
Whi
te n
on-
glos
sy p
aper
Car
dboa
rd
Ply
woo
d
Bla
ck ru
bber
Black
non-g
lossy
pa
per (
Lightn
ess:
5)
250.984 50 mm
1.969 in25 mm0.984 in
0
Whi
te
Yel
low
Ora
nge
Bro
wn
Gre
en
Bla
ck
Red
Blu
e
Gra
y
Set
ting
dist
ance
L (
mm
in)
Dis
tanc
e L
(mm
in)
50 mm1.969 in25 mm0.984 in
Sen
sing
ran
ge L
(m
m in
)S
ettin
g di
stan
ce L
(m
m in
)
Sen
sing
ran
ge L
(m
m in
)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
20
CX-400
SENSING CHARACTERISTICS (TYPICAL)
CX-442
These bars indicate the sensing range with the re- spective objects when the distance adjuster is set to a sensing range of 100 mm 3.937 in, 50 mm 1.969 in long, respectively, with white non-glossy paper.
These bars indicate the sensing range with the respective colors when the distance adjuster is set to a sensing range of 100 mm 3.937 in, 50 mm 1.969 in long, respectively, with white color.The sensing range also varies depending on material.
• Setting distance: 50 mm 1.969 in • Setting distance: 100 mm 3.937 in
Correlation between material (5050 mm 1.9691.969 in) and sensing range
Correlation between color(5050 mm 1.9691.969 in construction paper) and sensing range
Emitted beam
0 0
CX-444 Adjustable range reflective type
Sensing fields• Setting distance: 25 mm 0.984 in
100 mm3.937 in
50 mm1.969 in
1003.937
501.969
0 0
1003.937
501.969
200.787
401.575
602.362
803.150
L #
Sensor
100.394
200.787
301.181
401.575
Sensor0
"9 mm "0.354 in
"8 mm "0.315 in
"6.5 mm "0.256 in
"5.3 mm "0.209 in20
0.787
803.150
1003.937
501.969
0
501.969
1003.937
L #
Sensor
100 mm3.937 in
50 mm1.969 in
# # ## #
#
Adjustable range reflective type
• Setting distance: 200 mm 7.874 in • Setting distance: 300 mm 11.811 in40015.748
Sensing fields• Setting distance: 100 mm 3.937 in
Correlation between color(5050 mm 1.9691.969 in construction paper) and sensing range
100.394
50.197
0 50.197
100.394
0
501.969
1003.937
100.394
50.197
0 50.197
100.394
1003.937
2007.874
100.394
1003.937
2007.874
30011.811
Black non-glossy paperLightness: 5
Sensor
5050 mm 1.9691.969 inNon-glossy paper
Black non-glossy paperLightness: 5
White non-glossy paper
5050 mm 1.9691.969 inNon-glossy paper
Left RightCenterOperating point ?(mm in)
Left RightCenterOperating point ?(mm in)
White non-glossy paper
L
0
L
Sensor
50.197
0 50.197
100.394
100.394
50.197
0 50.197
100.394
100.394
50.197
0 50.197
100.394
100.394
50.197
0 50.197
100.394
0
L
Sensor
Black non-glossy paperLightness: 5
5050 mm 1.9691.969 inNon-glossy paper
Left CenterOperating point ?(mm in)
White non-glossy paper
These bars indicate the sensing range with the re- spective objects when the distance adjuster is set to a sensing range of 300 mm 11.811 in, 200 mm 7.874 in and 100 mm 3.937 in long, respectively, with white non-glossy paper.
Correlation between material (5050 mm 1.9691.969 in) and sensing range
Emitted beam
1.18130
40015.748
0
15 mm 0.591 in
11 mm 0.433 in
9 mm 0.354 in
"8 mm "0.315 in
1003.937
30011.811
2007.874
Right
These bars indicate the sensing range with the respective colors when the distance adjuster is set to a sensing range of 300 mm 11.811 in, 200 mm 7.874 in and 100 mm 3.937 in long, respectively, with white color.The sensing range also varies depending on material.
0
1003.937
40015.748
30011.811
Whi
te n
on-
glos
sy p
aper
Car
dboa
rd
Ply
woo
d
Bla
ck ru
bber
Black
non-g
lossy
pa
per (
Lightn
ess:
5)
Whi
te n
on-
glos
sy p
aper
Car
dboa
rd
Ply
woo
d
Bla
ck ru
bber
Black
non-g
lossy
pa
per (
Lightn
ess:
5)
2007.874
Whi
te
Yel
low
Ora
nge
Red
Bro
wn
Gre
en
Blu
e
Gra
y
Bla
ck
Whi
te
Yel
low
Ora
nge
Red
Bro
wn
Gre
en
Blu
e
Gra
y
Bla
ck
1003.937
40015.748
30011.811
2007.874
0
Set
ting
dist
ance
L (
mm
in)
Set
ting
dist
ance
L (
mm
in)
Set
ting
dist
ance
L (
mm
in)
Dis
tanc
e L
(mm
in)
Left RightCenterOperating point ?(mm in)
Left RightCenterOperating point ?(mm in)
Left CenterOperating point ?(mm in)
Right
Set
ting
dist
ance
L (
mm
in)
Set
ting
dist
ance
L (
mm
in)
Set
ting
dist
ance
L (
mm
in)
Dis
tanc
e L
(mm
in)
Sen
sing
ran
ge L
(m
m in
)
100 mm3.937 in
200 mm7.874 in
300 mm11.811 in
100 mm3.937 in
200 mm7.874 in
300 mm11.811 in
Sen
sing
ran
ge L
(m
m in
)
Sen
sing
ran
ge L
(m
m in
)
Sen
sing
ran
ge L
(m
m in
)
Black non-glossy paperLightness: 5
5050 mm 1.9691.969 inNon-glossy paper
White non-glossy paper
L
Black non-glossy paperLightness: 5
White non-glossy paper
5050 mm 1.9691.969 inNon-glossy paper
Black non-glossy paperLightness: 5 5050 mm
1.9691.969 inNon-glossy paper
White non-glossy paper
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
21
CX-400
All models
PRECAUTIONS FOR PROPER USE
This product is not a safety sensor. Its use is not intended or designed to protect life and prevent body injury or property damage from dangerous parts of machinery. It is a normal object detection sensor.
Others•
•
•
•
•
•
•
Do not use during the initial transient time (50 ms) after the power supply is switched on.Take care that the sensor is not directly exposed to fluorescent light from a rapid-starter lamp or a high frequency lighting device, as it may affect the sensing performance.This sensor is suitable for indoor use only.Do not use this sensor in places having excessive vapor, dust, etc., or where it may come in direct contact with water or corrosive gas.Take care that the sensor does not come in direct contact with water, oil, grease or organic solvents, such as, thinner, etc.This sensor cannot be used in an environment containing inflammable or explosive gases.Never disassemble or modify the sensor.
CX-41/42CX-49/48
• Make sure that the power supply is off while wiring.• Take care that wrong wiring will damage the sensor.• Verify that the supply voltage variation is within the rating.• If power is supplied from a commercial switching regulator, ensure
that the frame ground (F.G.) terminal of the power supply is connected to an actual ground.
• In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this product, connect the frame ground (F.G.) terminal of the equipment to an actual ground.
Wiring
• Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This can cause malfunction due to induction.
• Extension up to total 100 m 328.084 ft (thru-beam type: both emitter and receiver) is possible with 0.3 mm2, or more, cable. However, in order to reduce noise, make the wiring as short as possible.
• Make sure that stress by forcible bend or pulling is not applied directly to the sensor cable joint.
Operation mode switch
DescriptionOperation mode switch
Light-ON mode is obtained when the operation mode switch (located on the receiver for the thru-beam type) is turned fully clockwise (L side).
Dark-ON mode is obtained when the operation mode switch (located on the receiver for the thru-beam type) is turned fully counterclockwise (D side)
Functional descriptionStability indicator(Green) (Note 1)Lights up under the stable light condition or the stable dark condition
Operation indicator(Orange) (Note 2)Lights up when the output is ON( )
L : Light-OND : Dark-ON
Operation mode switch(Note 1)
( )
( )Sensitivity adjuster(Note 1)Sensing range becomes longer when turned clockwise( )
Notes: 1)2)
Not incorporated on the thru-beam type sensor emitter. It is the power indicator (Green LED)(lights up when the power is ON) for the thru-beam type sensor emitter.
MIN
MA
X
3 Similarly, adjust for up, down, left and right angular movement of the emitter.
4 Further, perform the angular adjustment for the receiver also.5 Check that the stability indicator (green) lights up.6 Choose the operation mode, Light-ON or Dark-ON, as per your
requirement, with the operation mode switch.
Sensing object
Receiver
Emitter
Beam alignment
Thru-beam type sensor
1 Set the operation mode switch to the Light-ON mode position (L side).2 Placing the emitter and the receiver face to face along a straight
line, move the emitter in the up, down, left and right directions, in order to determine the range of the light received condition with the help of the operation indicator (orange). Then, set the emitter at the center of this range.
Retroreflective type sensor
1 Set the operation mode switch to the Light-ON mode position (L side).2 Placing the sensor and the reflector face to face along a straight
line, move the reflector in the up, down, left and right directions, in order to determine the range of the light received condition with the help of the operation indicator (orange).Then, set the reflector at the center of this range.
3 Similarly, adjust for up, down, left and right angular movement of the reflector.
4 Further, perform the angular adjustment for the sensor also.5 Check that the stability indicator (green) lights up.6 Choose the operation mode, Light-ON or Dark-ON, as per your
requirement, with the operation mode switch.
Sensing object
Sensor
Reflector
Mounting• The tightening torque should be 0.5 N m or less.
M3 (length 12 mm 0.472 in) screw with washers Sensor
mounting bracket(Optional)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
22
CX-41/42CX-49/48
CX-400
Retroreflective type sensor (except CX-491)
Retroreflective type sensor for transparent object sensing (CX-48)• Optimum sensing is possible when the position of the transparent sensing object is set at the center of the sensor and the reflector.If the sensing position is set near the sensor or the reflector, the sensing may be unstable. In this case, set the sensing position at the center of the sensor and the reflector.
•
•
When the sensor detects an uneven plastic receptacle or glass bottle, the received-light amount may differ with the sensing position or direction. Adjust the sensitivity after confirming the stable sensing condition by turning the sensing object, etc.When sensing pipe-shaped transparent sensing object, set it in a standing, not lying, position as shown in Figure A. The sensor may fail to detect a lying object as shown in Figure B.
• Please take care of the following points when detecting materials having a gloss.
1
2
Make L, shown in the diagram, sufficiently long.Install at an angle of 10 to 30 degrees to the sensing object.
L
10 to 30
Sensingobject
ReflectorGlossy surface
Make L sufficiently long
Reflector
Sensor
B
Reflector
Sensor
A
Sensor Reflector Transparent sensing object
PRECAUTIONS FOR PROPER USE
Sensitivity adjustment
DescriptionStep
1
2
3
4
Sensitivityadjuster
Turn the sensitivity adjuster fully counter-clockwise to the minimum sensitivity position, MIN.
Optimum position
In the light received condition, turn the sensitivity adjuster slowly clockwise and confirm the point A where the sensor enters the ‘Light’ state operation.
( )
In the dark condition, turn the sensitivity adjuster further clockwise until the sensor enters the ‘Light’ state operation and then bring it back to confirm point B where the sensor just returns to the ‘Dark’ state operation.
If the sensor does not enter the ‘Light’ state operation even when the sensitivity adjuster is turned fully clockwise, the position is point B .
The position at the middle of point A and Bis the optimum sensing position.
Note: Use the ‘minus’ adjusting screwdriver (please arrange separately) to turn the adjuster slowly. Turning with excessive strength will cause damage to the adjuster.
MIN
MA
X
MIN
MA
X
MIN
MA
X
MIN
MA
X
B
B
Dark conditionLight received condition
Sensor
Sensing object
Sensing object
Sensor Sensor
Sensingobject
ReflectorSensor Reflector
Emitter ReceiverReceiverEmitter
Diff
use
refle
ctiv
e ty
peT
hru-
beam
type
Ret
rore
flect
ive
type
Relation between output and indicators
Stabilityindicator
Stabilityindicator
Operationindicator
Operationindicator
In case of Light-ON
, : lights up : lights off
In case of Dark-ON
Output Output
ON OFF
OFF ON
Sensingcondition
Stable light receiving
Unstable light receiving
Unstable dark receiving
Stable dark receiving
Retroreflective type sensor with polarizing filters (CX-491)
Example of sensing objects
• If a shiny object is covered or wrapped with a transparent film, such as those described below, the retroreflective type sensor with polarizing filters may not be able to detect it. In that case, follow the steps given below.
• Can wrapped by clear film• Aluminum sheet covered by plastic film• Gold or silver color (specular) label or wrapping paper
Steps
• Tilt the sensor with respect to the sensing object while fitting.• Reduce the sensitivity.• Increase the distance between the sensor and the sensing object.
<Correct> <Incorrect>
A
A
A
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
23
CX-400
CX-44
BGS
FGS
CX-41
L-ON
D-ON
L-ON
D-ON
Non-detectable area
ONOFF
ONOFF
ONOFF
ONOFF
PRECAUTIONS FOR PROPER USE
Slit mask (Optional) • With the slit mask (OS-CX-), the sensor can detect a small
object.However, the sensing range is reduced when the slit mask is mounted.
How to mount
1 Insert the fixing hook into the fixing groove.2 Then, pressing the slit mask against the main unit, insert the
fixing tab into the fixing groove.
How to remove
1 Insert a screwdriver into the removing tab.2 Pull forward while lifting the removing tab.
Fixing tabFixing groove
Fixing groove
Fixing hook
Removing tab
Slit mask
Interference prevention filter (Optional)(Exclusively for CX-411)• By mounting interference prevention filters (PF-CX4-), two sets
of CX-411 can be mounted close together.However, the sensing range is reduced when the interference prevention filter is mounted.
• The filters can be mounted by the same method as for the slit masks.
• The two sets of sensors should be fitted with different types of interference prevention filters.Interference prevention does not work if the filters are mounted for emitters only, receivers only or if the same model No. of interference prevention filters are mounted on both sets of sensors.
Fitted withPF-CX4-V
Fitted withPF-CX4-H
Do not make the sensor detect an object in this direction because it may cause unstable operation.
Sensing object Sensing objectSensing object
Tilt
Care must be taken regarding the sensor mounting direction with respect to the object’s direction of movement.
•
•
•
When detecting a specular object (aluminum or copper foil, etc.) or an object having a glossy surface or coating, please take care that there are cases when the object may not be detected due to a change in angle, wrinkles on the object surface, etc.When a specular body is present below the sensor, use the sensor by tilting it slightly upwards to avoid wrong operation.
•
•
If a specular body is present in the background, wrong operation may be caused due to a small change in the angle of the background body. In that case, install the sensor at an inclination and confirm the operation with the actual sensing object.Take care that there is a non-detectable area right in front of the sensor.
Specularface
Depending on whether you select the BGS or FGS function, the output operation changes as follows.
Operation mode switchMounting
L D
L D
DescriptionOperation mode switch
Detection-ON mode is obtained when the operation mode switch is turned fully clockwise (L side).
Detection-OFF mode is obtained when the operation mode switch is turned fully counterclockwise (D side).
Note: Use the ‘minus’ screwdriver (please arrange separately) to turn the adjuster slowly. Turning with excessive strength will cause damage to the adjuster.
•
Sensing range
Setting distance
<Correct> <Correct> <Incorrect>
<Incorrect> <Correct>
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
24
CX-400
CX-44
PRECAUTIONS FOR PROPER USE
Stability indicator
Sensor
Output (Operation indicator)(BGS mode Detection-ON)
Stability indicator
• Since the CX-44 uses a 2-segment photodiode as its receiving element, and sensing is done based on the difference in the incident beam angle of the reflected beam from the sensing object, the output and the operation indicator (orange) operate according to the object distance. Furthermore, the stability indicator (green) shows the margin of the setting distance.
Sensing object
ON (Lights up)
OFF (Lights off)
Stable operatingcondition
Stable operatingcondition
Lights up
Lights offUnstable operating condition
Setting distance
BGS / FGS functionsThis sensor incorporates BGS / FGS functions. Select either BGS or FGS function depending on the positions of the background and sensing object.
This function is used when the sensing object is apart from the background.
BGS function
FGS function
This function is used when the sensing object contacts the background or the sensing object is glossy, etc.
Sensingobject
Bac
kgro
und
Sensingobject
Background
•
•
•
Turn the distance adjuster gradually and lightly with a ‘minus’ screwdriver (please arrange separately). In order to protect itself, the distance adjuster idles if turned fully. If the adjuster is idled when distance adjustment is done, carry out the adjustment again.
Distance adjustment
When this product is used, be sure to carry out the distance adjustment.Since the distance adjuster of this sensor is a 5-turn adjuster, when the point A and B is adjusted as explained in the table right, there may be more than 1 turn between the point A and B. Therefore, make sure to remember the turns of both points to find the optimum position.Be sure to wire the sensing mode selection input (Pink / 2) before distance adjustment. If the wiring is done after the distance adjustment, the sensing area is changed.
•
•
•
•
BGS function
1
2
3
4
Step Description Distance adjuster
Turn the distance adjuster fully counterclockwise to the minimum sensing range position. (CX-441/443/ 444: 20 mm 0.787 in approx., CX-442: 40 mm 1.575 in approx.)
Remove the object, turn the adjuster clockwise further until the sensor goes into the detecting state again. Once it has entered, turn the distance adjuster backward until the sensor returns to the non-detecting condition. This position is designated as point B. When the sensor does not go into the detecting condition even if the adjuster is turned fully clockwise, the position where the adjuster was fully turned is regarded as the point B.
There may be more than 1 turn between point A and B, since this sensor incorporates a 5-turn adjuster.
Place an object at the required distance from the sensor, turn the distance adjuster gradually clockwise, and find out point A where the sensor changes to the detecting condition.
Turn fully
FGS function
1
2
3
4
Step Description Distance adjuster
Turn the distance adjuster fully clockwise to the maximum sensing range position. (CX-441/443: 50 mm 1.969 in approx., CX-444: 100 mm 3.937 in approx., CX-442: 300 mm 11.811 in approx.)
Place an object at the required distance from the sensor, turn the adjuster counterclockwise further until the sensor goes into the non-detecting condition again. Once entered, turn the distance adjuster backward until the sensor returns to the detecting condition. This position is designated as point B. When the sensor does not go into the non-detecting condition even if the adjuster is turned fully counterclockwise, the position where the adjuster was fully turned is regarded as the point B.
There may be more than 1 turn between point A and B, since this sensor incorporates a 5-turn adjuster.
In the state where the sensor detects the background, turn the distance adjuster gradually counterclockwise, and find out point A where the sensor changes to the non-detecting condition.
Optimum position
Turn fully
Optimum position
The optimum position to stably detect objects is the center point between A and B.
The optimum position to stably detect objects is the center point between A and B .
Others • Its distance adjuster is mechanically operated. Do not drop; avoid
other shocks.
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
25
CX-400
CX-41-J Sensor
Sensor Sensor
CX-49 CX-48CX-42
CX-49-Z CX-48-ZCX-42-Z
CX-49-J CX-48-JCX-42-J
Sensor
DIMENSIONS (Unit: mm in)
CX-41 Sensor CX-41-Z Sensor
The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/
Notes: 1)2)
Not incorporated on the emitter.It is the power indicator (green) on the emitter.
Notes: 1)2)
Not incorporated on the emitter.It is the power indicator (green) on the emitter.
Notes: 1)2)
Not incorporated on the emitter.It is the power indicator (green) on the emitter.
2.50.098
3 0.118
3.95 0.1567.85 0.309
11.90.469
Beam axis
11.20.441
Operation indicator (Orange)(Note 2)
Stability indicator (Green)(Note 1)
Sensitivity adjuster (Note 1)
Operation mode switch (Note 1)
15.5 0.610
"3.7 "0.146 cable, 2 m 6.562 ft long
25.41.000
2-M30.5 0.020thru-hole threads
( )
200.787
311.220
Operation indicator (Orange)(Note 2)
Sensitivity adjuster (Note 1)
3.95 0.1567.85 0.309
11.90.469
2.50.098
30.118
42.51.673
35.51.398
311.220
25.41.000
15.50.610
Stability indicator (Green)(Note 1)
Beam axis
11.20.441
"9.4"0.370
Operation mode switch (Note 1)
M8 connector
2-M30.5 0.020thru-hole threads
200.787
( )
3.95 0.1567.85 0.309
11.90.469
Operation indicator (Orange)(Note 2)
Stability indicator (Green)(Note 1)
Sensitivity adjuster (Note 1)
Operation mode switch (Note 1)
30.118
200.787
2.50.098 M12 connector31
1.22025.41.000
15.5 0.610
"3.7 "0.146 cable
Beam axis
11.20.441
2-M30.5 0.020thru-hole threads
30011.811( )
( )
( )( )
441.732
3.95 0.1567.85 0.309
11.90.469
Operation indicator (Orange)
Stability indicator (Green)
Sensitivity adjuster
Operation mode switch
4 0.1572.5
0.098
30.118
11.20.441Beam-receiving
part
15.5 0.610
Center of sensing
25.41.000
40.157
Beam-emittingpart
2-M30.5 0.020thru-hole threads "3.7 "0.146 cable,
2 m 6.562 ft long
311.220
200.787
( )
30.118
2.50.098 ( )2.5
0.098
11.90.469
7.85 0.3093.95 0.156
Sensitivity adjuster
Operation indicator (Orange)
Stability indicator (Green) Operation mode switch
25.41.000
15.5 0.610
2-M30.5 0.020thru-hole threads
Center of sensing
M8 connector
11.20.441
"9.4"0.370
Beam-emittingpart
Beam-receivingpart
40.1574
0.157
42.51.673
200.787
200.787
35.51.398
311.220
11.90.469
7.85 0.3093.95 0.156
Operation mode switch
Sensitivity adjuster
Operation indicator (Orange)
Stability indicator (Green)
Center of sensing
2-M30.5 0.020thru-hole threads
Beam-emittingpart
Beam-receivingpart
15.5 0.6104 0.157
40.157
11.20.441 3
0.118
"3.7 "0.146 cable
M12 connector
( )441.732
( )30011.811
311.220
25.41.000
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
26
CX-400
RF-230 Reflector Accessory for the retroreflective type sensor
RF-220 Reflector (Optional)
DIMENSIONS (Unit: mm in)
RF-12 Reflective tape (Optional)RF-11 Reflective tape (Optional)
RF-210 Reflector (Optional)
The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/
RF-13 Reflective tape (Optional)
CX-44 CX-44-ZSensor Sensor
0.50.020
( )
Material: Acrylic (Reflector) ABS (Base)
Material: Acrylic (Reflector) ABS (Base)
Material: Acrylic (Reflector) ABS (Base)
Two M3 (length 8 mm 0.315 in) screws with washers and two nuts are attached.
Material: Acrylic Material: Acrylic
2-"4.6 "0.181mountingholes
50.31.980
401.575
5 0.197
8.30.327
3.30.130
10 0.394
59.32.335
49.31.941
( )301.181
35.31.390
42.31.665
34.31.350
250.984
2-"3.6 "0.142mountingholes
4 0.1578 0.315
8.30.327
3.30.130
210.827( )
33.31.311
ReflectorM3 nut mounting holes(for mounting at the back)
Base
250.984
3.20.126
100.394
2-"3.4 "0.134 thru-holes(for mounting at the side)
(for mounting at the back)
2-"3.4 "0.134 holes, 6 0.236 deep
(for mounting at the side)2-M3 nut mounting holes
12.8 0.504
11 0.433
80.315
281.102
60.236
301.181
Adhesivetape
Effective reflecting surface
0.70.028
( )
( )
( )
301.181
301.181
301.181
0.70.028
281.102
250.984
230.906
Adhesivetape
Effective reflecting surface
( )
( )Reflective surface (Acrylic)
Rear surface pressure-sensitiveadhesive
40.157
8.20.323
12.50.492
Stability indicator (Green)
Operation mode switchDistance adjuster (5-turn)
Operation indicator (Orange)
3 0.118
0.90.035
200.7872.8
0.110
20.07911.2
0.441
2-M30.5 0.020 thru-hole threads
220.866
Beam-receiving part
Beam-emitting part
Center of sensing
"3.7 "0.146 cable, 2 m 6.562 ft long
220.866
"9.4 0.370
2-M30.5 0.020 thru-hole threads
11.20.441
Beam-receiving part
Beam-emitting partCenter of
sensing
311.220
25.41.00042.5
1.673
35.51.398
2.80.110
20.079 3 0.118
0.90.035
M8 connector
40.157
8.20.323
12.50.492
Stability indicator (Green)
Operation mode switchDistance adjuster (5-turn)
Operation indicator (Orange)
311.220
25.41.000
200.787
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
27
CX-400
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/
MS-CX2-1 Sensor mounting bracket (Optional)
Assembly dimensions
Assembly dimensions
Assembly dimensions
MS-CX2-2 Sensor mounting bracket (Optional)
MS-CX2-4 Sensor mounting bracket (Optional)
Material: Stainless steel (SUS304)
Two M3 (length 12 mm 0.472 in) screwswith washers are attached.
Material: Stainless steel (SUS304)
Two M3 (length 12 mm 0.472 in) screwswith washers are attached.
Material: Stainless steel (SUS304)
Two M3 (length 14 mm 0.551 in) screwswith washers are attached.
3.40.134
8 0.31514 0.551
50.197
30.118
3.40.134
14
10 0.394
72-"3.4 "0.134 holes(for RF-210)
3.40.134
12.5 0.492
t 1.2t 0.047
120.472
R12R0.472
220.866
150.591
200.787
R25R0.984
250.98442.5
1.673 Beam axis
9.50.374
250.984
12.3 0.484t 1.2
t 0.047
25.41.000
0.40.0167
13.6 0.535
3.40.134
3.40.134
50.197
30.118
14
120.472
R12 R0.472
0.50.020
311.220 42.5
1.673
( )
( )
220.866
25.2 0.992
200.787
15.80.622
t 2t 0.079 5 0.197
4.50.177
4.50.177
14
7.80.307
4.5 0.1774 0.157
120.472
7.80.307
7 0.276
230.906
100.394
8-"3.4 "0.134 holes
R12 R0.472
140.551
70.276
140.551
Beam axis
15.80.622
8.20.323
t 2t 0.079
3.60.142
40.157
140.551
4.50.177
4.50.177
120.472
5 0.197
14R12 R0.472
7 0.276
4.5 0.177
40.157
8.2 0.323
361.417
552.165
22 0.866
250.984
15.50.610
281.102
552.165
361.417
220.866
25.41.000
15.50.610
3.40.134
3.40.134
40.1577
14
"25 "0.984 R25
R0.984
SE
NS
OR
180.709
130.512
t 2.5t 0.098
6.20.244
R9.5R0.374
SE
NS
OR
291.142
190.748
5.50.217
5.50.217
60.236
70.276
2040
"55 "2.165"39 "1.535
250.984
250.984
250.984
190.748
461.811
2040
70.276
0.90.035
130.512 11.2
0.4410.90.035
12.3 0.484
250.984
2.5 0.098
Beam axis
461.811 SE
NSO
R
SENSO
R
"55 "2.165"39 "1.535
291.142
180.709
25.41.000
Mounting drawing with the receiver of CX-41
Mounting drawing with the receiver of CX-41
Mounting drawing with the receiver of CX-41
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
28
CX-400
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/
MS-CX2-5 Sensor mounting bracket (Optional)
MS-CX-3 Sensor mounting bracket (Optional)
MS-RF21-1 Reflector mounting bracket for RF-210 (Optional)
Assembly dimensions
Material: Stainless steel (SUS304)
Two M3 (length 12 mm 0.472 in) screwswith washers are attached.
Assembly dimensions
Material: Stainless steel (SUS304)
Two M3 (length 12 mm 0.472 in) screwswith washers are attached.
Assembly dimensions
Material: Stainless steel (SUS304)
Two M3 (length 12 mm 0.472 in) screwswith washers are attached.
3.40.1343.4
0.134
3.50.138
6.5 0.256
5 0.197
7
150.591 t 1.5
t 0.059
80.315
50.197
7.90.311
70.276
451.772
18.90.744
371.457
200.787
190.748
250.984
R19R0.748R25
R0.984
t 1.5t 0.059
25.41.000
Beam axis
7R25
R0.984
70.276
200.787
6.5 0.2565 0.197
50.197
7.9 0.311
20.60.81126.2
1.031
451.772
18.90.744
t 1.2t 0.047
20.50.807
3.50.138
3.40.134
3.40.134
10R25R0.984
50.197
3.40.134105
0.19715
0.591
140.5518
0.315 3.40.134
60.236
8.50.335
60.236
30 1.181
351.378
250.984
180.709
13.60.535
3.40.134 8
0.31514
0.551
60.236
9 0.354
8.50.335
180.709
Beam axis
0.50.020
3.50.138
4.80.189
t 1.2t 0.047
0.40.01610
25.20.992
11.20.441
6 0.236
311.220
301.181
25.41.000
351.378
( )
12.5 0.492
t 1.2t 0.047
130.512
"25"0.984
160.63010
0.3943.50.138
3.20.126
R7.5R0.295
250.984
461.811
20
230.906
501.969
5.50.217
"36"1.417
30
461.811
250.984
130.512
100.394
20
501.969
"36"1.417
30
230.9065.5
0.217
Mounting drawing with the receiver of CX-41
Mounting drawing with the receiver of CX-41
190.748
371.457
200.787
150.591
R25R0.984
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
29
CX-400
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/
MS-RF22 Reflector mounting bracket for RF-220 (Optional)
Assembly dimensions
MS-RF23 Reflector mounting bracket for RF-230 (Optional)
Assembly dimensions
Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated)
Two M3 (length 8 mm 0.315 in) screws with washers are attached.
Material: Cold rolled carbon steel (SPCC)(Uni-chrome plated)
Two M4 (length 10 mm 0.394 in) screws with washers are attached.
4.50.177
100.394
110.433
250.984
351.378
40.157
16 0.630
10 0.394
6 0.2368 0.315
441.732
200.787
t 1.6t 0.063
8-M30.5 0.020thru-hole threads
4.50.177
250.984
100.394 28.3
1.114
8.30.327
34.31.350
8 0.315
40.157
210.827
35.31.390
44.31.744
60.236
271.063
t 1.6t 0.063
19.30.760
( ) ( )
401.575 4.5
0.1773
0.118 100.394 11
0.433
501.969
401.575
5 0.197
16 0.630
15 0.591
18 0.709
7 0.276
200.787
t 2t 0.079
8-M40.7 0.028 thru-hole threads
261.024
120.472
351.378
30.118
612.402
( )
( ) 281.102( )
401.5754.5
0.177
28.31.11419.3
0.760
8.30.327
100.394
50.31.980
49.31.941
50.197
t 2t 0.07910
0.394
301.181
61.32.413
70.276
371.457
401.575
( )( )
250.984
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
30
CX-400
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/
MS-AJ1-A Universal sensor mounting stand (Optional) MS-AJ2-A Universal sensor mounting stand (Optional)
MS-AJ2 Universal sensor mounting stand (Optional)MS-AJ1 Universal sensor mounting stand (Optional)
Assembly dimensions with CX-400 series(Mounting part only)
Assembly dimensions with RF-210 (Reflector)(Mounting part only)
( )
( )
( )
( )
( )
( )
( )
( ) ( )( )
( )
( )
( )
11.80.465
20 0.787
17.80.701 12
0.472t 2t 0.079
2-"3.2 "0.126mounting holes
2-3.2 0.1264.2 0.165oblong holes
45
45
4.2 0.165
3.20.126
M4 hexagon-socket-headbolt
1 0.039
10.039
200.787
250.984
331.299
200.787Attachment
(Nylon 6)
Sensor mounting bracket[Stainless steel (SUS304)]
"10 "0.394 pipe[Stainless steel (SUS304)]
2-"6.6 "0.260mounting holes
Base(PA)
321.26046
1.81120
0.787
80.315
150.591
311.220
200.787
36.51.437
( )( )
( )
1475.787 (Note)
Cable guide(POM)
100.394
24.50.965
200.787
2108.268
281.102
6 0.236
40.157
25.51.004
100.394
2-"6.6 "0.260 mounting holes
451.772
321.260
Base(PA)
80.315
180.709
200.787
281.102
200.787
1 0.039
200.787
10.039
250.984
331.299
17.80.701 12
0.47211.8
0.465
44.51.752
2188.583
1475.787
281.102
45
45
t 2t 0.079
6 0.23620 0.787
Attachment(Nylon 6) M4 hexagon-
socket-headbolt
2-"3.2 "0.126mounting holes
2-3.2 0.1264.2 0.165oblong holes
"10 "0.394 pipe[Stainless steel (SUS304)]
Sensor mounting bracket[Stainless steel (SUS304)]
Cable guide(POM)
4.2 0.165
3.20.126
(Note)
40.157
200.787
( )( )
( )
200.787
11.80.465
331.299
200.787
281.10227
1.063
17.60.693
45
45
t 2 t 0.0796
0.236
Center of sensing
2-M3 (length14 mm 0.551 in)screws with washers
4.20.165
25.41.000
23.20.913
18.40.724
24.80.976
45
45
t 2t 0.079
250.984
33.31.311
31.81.252
200.787
2-M3 (length14 mm 0.551 in)screws withwashers
4.20.165
200.787
11.80.465
60.236
331.299
25.51.004
100.394
2-"6.6 "0.260 mounting holes
451.772
321.260
Base(PA)
80.315
180.709
200.787
281.102
28.451.120
120.472
16.50.650
1475.787
(Note 1)
44.51.752
203.58.012
1345.276 (Note 1)
331.299
2108.268
16.50.650
331.299
6 0.236
2188.583
2-"3.2 "0.126mounting holes
Arm joint(Nylon 6)
"10 "0.394 pipe[Stainless steel (SUS304)]
"10 "0.394 pipe[Stainless steel (SUS304)]
2-3.2 0.1264.2 0.165 oblong holes
Cable guide(POM)
Sensor mounting bracket[Stainless steel (SUS304)] (Note 2)
4.20.165
( )
24.50.965
321.260
461.811
Base(PA)
311.220
150.591
80.315
100.394
200.787
2-"6.6 "0.260mounting holes
28.451.120
120.472
16.50.650
1475.787
(Note 1)
36.51.437
208.58.209
1345.276 (Note 1)
331.299
2108.268
16.50.650
331.299
6 0.236
2108.268
200.787
2-"3.2 "0.126mounting holes
Arm joint(Nylon 6)
"10 "0.394 pipe[Stainless steel (SUS304)]
"10 "0.394 pipe
2-3.2 0.1264.2 0.165 oblong holes
Cable guide(POM)
Sensor mounting bracket[Stainless steel (SUS304)] (Note 2)
4.20.165 [Stainless steel (SUS304)]
Two M3 (length 14 mm 0.551 in) screws with washers, two M3 (length 16 mm 0.630 in) screws with washers, two M3 (length 18 mm 0.709 in) screws with washers, one auxiliary mounting plate for EQ-20 series and one auxiliary mounting plate for EX-40 series are attached.
Two M3 (length 14 mm 0.551 in) screws with washers, two M3 (length 16 mm 0.630 in) screws with washers, two M3 (length 18 mm 0.709 in) screws with washers, one auxiliary mounting plate for EQ-20 series and one auxiliary mounting plate for EX-40 series are attached.
Two M3 (length 14 mm 0.551 in) screws with washers, two M3 (length 16 mm 0.630 in) screws with washers, two M3 (length 18 mm 0.709 in) screws with washers, one auxiliary mounting plate for EQ-20 series and one auxiliary mounting plate for EX-40 series are attached.
Two M3 (length 14 mm 0.551 in) screws with washers, two M3 (length 16 mm 0.630 in) screws with washers, two M3 (length 18 mm 0.709 in) screws with washers, one auxiliary mounting plate for EQ-20 series and one auxiliary mounting plate for EX-40 series are attached.
Note: The dimensions in the brackets indicate the adjustable range of the movable part. Note: The dimensions in the brackets indicate the adjustable range of the movable part.
The dimensions in the brackets indicate the adjustable range of the movable part.Refer to MS-AJ1/AJ2 for the assembly dimensions with the sensor mounting bracket, sensor or reflector.
Notes: 1)
2)
The dimensions in the brackets indicate the adjustable range of the movable part.Refer to MS-AJ1/AJ2 for the assembly dimensions with the sensor mounting bracket, sensor or reflector.
Notes: 1)
2)
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
http://www.sunx.co.jp/
All information is subject to change without prior notice.
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/
MS-AJ1-M MS-AJ2-M
Assembly dimensions with RF-220 (Reflector)(Mounting part only)
Assembly dimensions with RF-230 (Reflector)(Mounting part only)
Universal sensor mounting stand (Optional) Universal sensor mounting stand (Optional)
Two M3 (length 8 mm 0.315 in) screws with washers and two M4 (length 8 mm 0.315 in) screws with washers are attached.
Two M3 (length 8 mm 0.315 in) screws with washers and two M4 (length 8 mm 0.315 in) screws with washers are attached.
Protecting the environment is one of SUNX’s guiding business principles
ISO 14001 environmental management system certification acquired
Our Nagoya Head Office and Factory acquired ISO 14001 certification in September 1999.Now and into the future, we will continuously improve environmental management systems based on our Environment Policy, which focuses on the promotion of environmentally friendly business activities and product development.
Promoting a totally lead-free working environment
We are now working to eliminate the use of lead in all our in-house manufacturing processes such as in reflow ovens, hand soldering and parts and substrates procurement.
Using simple packaging
Simple, environmentally friendly packaging material reduces waste.
(Note)147
5.787
180.709
281.102
11.80.465
25.51.004
100.394
321.260
2-"6.6 "0.260 mounting holes
"10 "0.394 pipe[Stainless steel (SUS304)]
80.31545
1.772
200.787
Base(PA)
200.787
281.102
2-M4
250.984
45
45
Attachment(Nylon 6)
2-M3 t 2 t 0.079
220.866
170.669
M4 hexagon-socket-head bolt
2088.189
501.969
401.575
44.51.752
4.20.165
220.866 2-M4
250.984
11.80.465
170.669
M4 hexagon-socket-head bolt
2-M3 t 2 t 0.079
45
45
281.102
200.787
Attachment(Nylon 6)
"10 "0.394 pipe[Stainless steel (SUS304)]
(Note)
321.260
24.50.965
311.220
150.591
80.315
461.811
Base(PA)
100.394
200.787
2-"6.6 "0.260mounting holes
200.787
2007.874
143.55.650
401.575
501.969
4.20.165
401.575
t 2t 0.079
M4 hexagon-socket-head bolt
200.787
11.80.465
35.31.390
281.102
45.31.783
281.102
45
45
36.31.429
200.7872-M3 (length 8 mm 0.315 in)
screws with washers
55.32.17738
1.49612
0.472
501.969
4.2 0.165
11.80.465
71.32.807
200.787
45
45
t 2t 0.079
2-M4 (length 8 mm 0.315 in)screws with washers
281.102
36.31.429
200.787
M4 hexagon-socket-head bolt47
1.850
50.31.980
371.457
61.32.413
( ) ( ) ( )
( )
( )
( )
4.2 0.165
The dimensions in the brackets indicate the adjustable range of the movable part.
Note: The dimensions in the brackets indicate the adjustable range of the movable part.
Note:
Clearwater Tech - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com
top related