Sony VPL-GH10 Optical Unit Replacement
Post on 17-Jul-2016
153 Views
Preview:
DESCRIPTION
Transcript
PROPRIETARY NOTICE: This document, including the information contained herein, is confidential and/or proprietary to CAE Inc., and shall not be reproduced or disclosed in whole or in part, or used for any purpose whatsoever without the prior written authorization of CAE Inc.
Rev 3 – 29 Apr 2015 TPD 19551
CAE SONY Projector VPL-GH10
Optical Block Replacement Procedure
CAE Inc. Confidential and/or Proprietary Information – see title page
Contact Information
CAE Inc., 8585 Cote de Liesse, Montreal, Quebec, Canada, H4T 1G6
CAE Inc. www.cae.com Customer Services caextranet.cae.com Trademarks and/or registered trademarks of CAE Inc. and/or its affiliates include but are not limited to CAE, CAE & Design, CAE Atmos, Atmos, CAE Exos, Exos, CAE Ionos, Ionos, CAE Lithos, Lithos, CAE Mesos, Mesos, CAE Stratos, Stratos, CAE Tropos, Tropos, CAE ROSE, ROSE, CAELIB, CAE Medallion, Medallion, CAE Medallion-S, Medallion-S,CAE Simfinity, Simfinity, CAE ITEMS, ITEMS, CAE RAVE, RAVE, CAE STRIVE, STRIVE, CAE TIGERS, TIGERS, and ROTORSIM. All other brands and product names are trademarks or registered trademarks of their respective owners. All logos, tradenames and trademarks referred to and used herein remain the property of their respective owners and may not be used, changed, copied, altered, or quoted without the written consent of the respective owner. All rights reserved.
Disclaimer
The information contained herein does not claim to provide for every possible contingency met in connection with the maintenance or operation of the training device. It is the user's responsibility to determine the usage of this information in conjunction with national, local and organizational health and safety codes, regulations, laws and practices (“Laws”). The procedures described herein under no circumstances may substitute the applicable Laws.
All maintenance and operating actions shall be undertaken by qualified personnel with the skills and knowledge relating to maintenance of the training device. Qualified personnel shall be trained and authorized, but not limited to, safely energize, de-energize, ground, lockout/tagout circuits and equipment, and clear faults in accordance with applicable Laws.
SONY Projector VPL-GH10
Record of Amendments
Record of Amendments
Rev 3 – 29 Apr 2015 Page i
CAE Inc. Confidential and/or Proprietary Information – see title page
Record of Amendments
Revision No. Date Description of Changes
- 03 Nov 2014 Initial Release.
1 18 Dec 2014 File name updated and steps added from the service manual.
2 17 Mar 2015 New part list and power supply installation steps.
3 29 Apr 2015 Updated the settings table and added sticker picture position
SONY Projector VPL-GH10
Table of Contents
Table of Contents
Rev 3 – 29 Apr 2015 Page iii
CAE Inc. Confidential and/or Proprietary Information – see title page
Table of Contents
1. Introduction ............................................................................................................................. 7 1.1 Objectives ........................................................................................................................7 1.2 List of Tools .....................................................................................................................8
2. GH10 Firmware Verification .................................................................................................. 9 3. GH10 Optical Block Change Procedure ............................................................................... 11
3.1 Data Save .......................................................................................................................12 3.2 Manual Data Reading ....................................................................................................15 3.3 Optical Block Removal ..................................................................................................17
3.3.1 Lens Types ............................................................................................................ 19 3.3.2 Detailed Removal Steps ........................................................................................ 20
3.4 Lamp Power Supply Removal .......................................................................................26
3.5 Projector Rebuild ...........................................................................................................29
3.6 Data Upload ...................................................................................................................31 3.6.1 NVM Selection ..................................................................................................... 33
3.7 Manual Data Modification .............................................................................................35 3.8 Projector Settings Update ..............................................................................................37
4. Conclusion ............................................................................................................................ 39
SONY Projector VPL-GH10
List of Figures
List of Figures
Rev 3 – 29 Apr 2015 Page v
CAE Inc. Confidential and/or Proprietary Information – see title page
List of Figures
Figure 1-1 Typical Optical Block ............................................................................................. 7 Figure 1-2 Parts List ................................................................................................................. 8 Figure 2-1 GH10 Projector ....................................................................................................... 9 Figure 2-2 Information Page ................................................................................................... 10 Figure 3-1 Flash Upgrader Settings ........................................................................................ 11
Figure 3-2 QuickAccess Window ........................................................................................... 12 Figure 3-3 Save Selection Chart ............................................................................................. 13 Figure 3-4 NVM SAVE section ............................................................................................. 13 Figure 3-5 Press Browse, Enter Info....................................................................................... 14 Figure 3-6 Selecting COM Port, Baud Rate ........................................................................... 14
Figure 3-7 Excerpt – Service Manual (1 of 2) ........................................................................ 17
Figure 3-8 Excerpt – Service Manual (2 of 2) ........................................................................ 18
Figure 3-9 SONY Lens (Do not remove) ............................................................................... 19 Figure 3-10 CNL (To be transferred to new optical block) ...................................................... 19 Figure 3-11 Vertical Locking Mechanism ................................................................................ 20 Figure 3-12 Spring Kit Locking Mechanism ............................................................................ 20
Figure 3-13 Horizontal Locking Mechanism ........................................................................... 21 Figure 3-14 Flaring Clamp ....................................................................................................... 21
Figure 3-15 Flaring Clamp – Zoom View ................................................................................ 22 Figure 3-16 Information Page ................................................................................................... 22 Figure 3-17 Guide Pin Locations .............................................................................................. 23
Figure 3-18 Removing CA and CA Board (1 of 2) .................................................................. 23 Figure 3-19 Removing CA and CA Board (2 of 2) .................................................................. 24
Figure 3-20 Removing Board and Holder ................................................................................ 24 Figure 3-21 Removing Optics Attachment ............................................................................... 25
Figure 3-22 Removing Pads ..................................................................................................... 25 Figure 3-23 Removing Fans ..................................................................................................... 25 Figure 3-24 Excerpt – Service Manual ..................................................................................... 26
Figure 3-25 Power Supply Cover Removal .............................................................................. 27 Figure 3-26 Removing Power Supply Connectors ................................................................... 27
Figure 3-27 Removing Connectors From QA Board ............................................................... 27 Figure 3-28 Screw Removal ..................................................................................................... 28 Figure 3-29 Lamp Power Supply Screws ................................................................................. 28
Figure 3-30 Removing Lamp Power Supply ............................................................................ 28 Figure 3-31 Heat Sink Removal ............................................................................................... 29
Figure 3-32 Horizontal Locking Mechanism ........................................................................... 30 Figure 3-33 QuickAccess Window ........................................................................................... 31
Figure 3-34 LOAD Selection Chart .......................................................................................... 31 Figure 3-35 Browse, Enter Name ............................................................................................. 32 Figure 3-36 Selecting COM port, Baud Rate ........................................................................... 32 Figure 3-37 Select Part, deselect Verify ................................................................................... 33 Figure 3-38 Browse, Select....................................................................................................... 33 Figure 3-39 Answer Yes To Continue Push ............................................................................. 34
SONY Projector VPL-GH10
List of Figures Rev 3 – 29 Apr 201 Page vi
CAE Inc. Confidential and/or Proprietary Information – see title page
Figure 3-40 When STBY LED Turns Red, Remove AC Power .............................................. 34
Figure 3-41 Settings Table (1 of 2 ............................................................................................ 37
Figure 3-42 Settings Table (2 of 2)........................................................................................... 38 Figure 4-1 Information Page ................................................................................................... 39 Figure 4-2 Suggested Sticker Location................................................................................... 39
SONY Projector VPL-GH10
Introduction
Introduction
Rev 3 – 29 Apr 2015 Page 7
CAE Inc. Confidential and/or Proprietary Information – see title page
1. Introduction
This procedure will guide you through the steps to replace the VPL-GH10 optical
block and lamp power supply. It will provide all the instructions on how to remove
and install the optical block, lamp power supply and identify all the needed software
and data to be updated during the process.
The received unit can come with FIRMWARE 9.02, 9.04, 9.06 or higher
installed.
The unit can come as GH10/0 (firmware 9.02 or 9.04) or GH10/1 (Firmware
9.06 and higher).
The unit can come with a Custom Navitar Lens (CNL) or a SONY lens.
1.1 Objectives
This manual documents the following procedures:
Replacing SONY VPL-GH10 optical block and lamp power supply.
Replacing the radiation pads, fans and fan cushions.
Updating data into the projector reflecting the optical block change.
Identify CNL vs SONY projector lenses.
Figure 1-1 shows the projector equipment that will be used in the optical block
replacement procedure. Figure 1-2 lists the individual components found in the
optical block assembly.
Figure 1-1 Typical Optical Block
SONY Projector VPL-GH10
Introduction Rev 3 – 29 Apr 201 Page 8
CAE Inc. Confidential and/or Proprietary Information – see title page
MA527304.01.2.258 Optical Block Assembly Parts List
PS418699.19.5.842 Parts List
Figure 1-2 Parts List
1.2 List of Tools
The following tools are needed to complete these tasks.
1) Allen Key 2.5 mm (SONY lens)
2) Allen Key 0.9mm (CNL lens)
3) Philips screw driver #2
4) Computer with serial port or EDGE port cable (USB to serial)
5) RS232 crossover cable
6) QUICKACCESS and FLASHUPGRADER software
7) New optical block (MA527304.01.2.258)
8) CD-ROM with specific optical block information
9) CNL Product Manual, Maintenance and Operation
10) SONY GH10 Service Manual
SONY Projector VPL-GH10
GH10 Firmware Verification
GH10 Firmware Verification
Rev 3 – 29 Apr 2015 Page 9
CAE Inc. Confidential and/or Proprietary Information – see title page
2. GH10 Firmware Verification
The following procedure is used to verify the projector's firmware version. To update
the optical block, the projector must have FIRMWARE 9.02, 9.04, 9.06 or higher
installed.
1) Turn ON the GH10 projector.
2) Verify the Firmware revision (must be in service mode).
a. Using the joystick (or the enter button in Figure 2-1), PRESS in sequence
ENTER-ENTER-LEFT-ENTER.
b. Answer Yes to enter Service mode
c. PRESS the MENU button
Figure 2-1 GH10 Projector
SONY Projector VPL-GH10
GH10 Firmware Verification Rev 3 – 29 Apr 201 Page 10
CAE Inc. Confidential and/or Proprietary Information – see title page
d. Select INFORMATION from the menu. See Figure 2-2.
e. Document the SC ROM Version, NVM Version, Sub ROM Version, and
IP ROM Version numbers.
Figure 2-2 Information Page
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure
GH10 Optical Block Change Procedure
Rev 3 – 29 Apr 2015 Page 11
CAE Inc. Confidential and/or Proprietary Information – see title page
3. GH10 Optical Block Change Procedure
For systems with firmware revision 9.02, 9.04 and 9.06, update the firmware to
revision 9.07 by performing the following steps:
1) Make sure the files, from the SONY supplied CD are in the same folder as the
QUICKACCESS and FLASHUPGRADER software.
2) Turn projector OFF. Projector is in STANBY mode (Do not remove power.).
3) Connect the RS232 cable to the unit.
4) Verify the serial port # and baud rate via Windows Device Manager.
5) Start FLASHUPGRADER software and make sure the proper settings are in
place as shown in Figure 3-1.
Figure 3-1 Flash Upgrader Settings
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure Rev 3 – 29 Apr 201 Page 12
CAE Inc. Confidential and/or Proprietary Information – see title page
6) Confirm selection of NOTIFY ON COMPLETION, RESET TARGET AFTER
DOWNLOAD and FLASH mode.
7) See Figure 3-1 and proceed as follows:
Select the CHOOSE button and select PW0P907a.inf file.
Confirm proper settings in COM PORT and BAUD RATE section. COM
port number is specific to the system. Confirm with the device manager.
Select EXT_232C_PW1 button.
Press FLASH.
NOTE: Always quit FLASHUPGRADER after each use.
NOTE: It can happen that the transfer stops at around 4%, CLOSE and
repeat the procedure. You may have to cycle power on the
projector.
8) Turn projector ON and verify the Firmware revision. Refer back to GH10
Firmware Verification, paragraph 2.
3.1 Data Save
1) Turn projector ON.
2) Connect the RS232 cable to the unit.
3) Start QUICKACCESS and select model VPL-GH10.
Figure 3-2 QuickAccess Window
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure
GH10 Optical Block Change Procedure
Rev 3 – 29 Apr 2015 Page 13
CAE Inc. Confidential and/or Proprietary Information – see title page
4) Select SAVE and select proper 3dgm/lut function, see Figure 3-3.
3dgm/lut function in pull down section File name
3DGamma 3DG_xxxxxxx.csv
LookUpTable LUT_ xxxxxxx.csv
DDC NOT NEEDED
ABGamma ABG_ xxxxxxx.csv
LCK LCK xxxxxxx.csv
OGMTable OGM_ xxxxxxx.csv
CSMatrixTable CSMatrix_ xxxxxxx.csv
NVM NVM_xxxxxxx.csv (see Figure 3-4) (Select SAVE_ALL)
NOTE: xxxxxxx represents the projector serial number.
Figure 3-3 Save Selection Chart
NOTE: It is necessary to record the serial number of the projector should you need
to revert back. Each optical block has files associated with it and cannot be
mixed. For the Non Volatile Memory (NVM) section the selection is as
follows:
Figure 3-4 NVM SAVE section
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure Rev 3 – 29 Apr 201 Page 14
CAE Inc. Confidential and/or Proprietary Information – see title page
5) Press BROWSE and type a name with the file associated in the function (refer
to SAVE SELECTION CHART, see Figure 3-3. Create a directory for each
optical block for clarity.
Figure 3-5 Press Browse, Enter Info
6) Select the proper COM port and baud rate (38400) and press NEXT to proceed.
Figure 3-6 Selecting COM Port, Baud Rate
7) Once completed, QUICKACCESS software will automatically quit.
8) Repeat steps 3) to 7), using the next proposed file from the SAVE SELECTION
CHART (see Figure 3-3).
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure
GH10 Optical Block Change Procedure
Rev 3 – 29 Apr 2015 Page 15
CAE Inc. Confidential and/or Proprietary Information – see title page
3.2 Manual Data Reading
The following procedure is used to document the device settings.
NOTE: The information to proceed can also be found in the GH10 Service
Manual, section 1-5-3 to 1-5-5.
Proceed as follows:
1) Turn projector ON.
2) Make sure the projector is in SERVICE MODE (Refer back to GH10 Firmware
Verification, paragraph 2.).
3) Select MENU on the projector.
4) Select DEVICE option and select OTHER for the IRIS data reading.
a. Press the down arrow to
b. 02 IRIS/OPEN REG menu and read value _____________________
c. 03 IRIS/CLOSE REG menu and read value _____________________
d. Press enter to go back to DEVICE menu.
5) From DEVICE menu, select PANEL DRIVER for the driver gain data reading
a. Press the down arrow to
b. 01 P.DRV/GAIN R menu and read value _____________________
c. 02 P.DRV/GAIN G menu and read value _____________________
d. 03 P.DRV/GAIN B menu and read value _____________________
e. Press enter to go back to DEVICE menu.
6) From DEVICE menu, select DISPLAY ENGINE
a. Press the down arrow to
b. 06 DE/R REG H menu and read value _____________________
c. 07 DE/R REG V and read value _____________________
d. 08 DE /B REG H and read value _____________________
e. 09 DE/B REG V and read value _____________________
f. Press enter to go back to DEVICE menu.
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure Rev 3 – 29 Apr 201 Page 16
CAE Inc. Confidential and/or Proprietary Information – see title page
7) From DEVICE menu, select OTHER for the LENS SHIFT data reading.
a. Press the down arrow to
b. 13 LENS SHIFT/H CENTER menu and read value _______________
c. 14 LENS SHIFT/V CENTER menu and read value _______________
d. 15 LENS SHIFT/V TOP menu and read value _______________
e. 16 LENS SHIFT/V BOTTOM menu and read value ______________
f. 17 LENS SHIFT/ RIGHT menu and read value _______________
g. 18 LENS SHIFT/LEFT menu and read value _______________
h. Press enter to go back to DEVICE menu.
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure
GH10 Optical Block Change Procedure
Rev 3 – 29 Apr 2015 Page 17
CAE Inc. Confidential and/or Proprietary Information – see title page
3.3 Optical Block Removal
Remove lamp, covers, filter and optical block as per Service Manual section 1-3-1 to
1-3-9, 1-3-12 and 1-3-14 to 1-3-15.
NOTE: Two screws at the front of the projector are intentionally missing.
Figure 3-7 Excerpt – Service Manual (1 of 2)
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure Rev 3 – 29 Apr 201 Page 18
CAE Inc. Confidential and/or Proprietary Information – see title page
Figure 3-8 Excerpt – Service Manual (2 of 2)
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure
GH10 Optical Block Change Procedure
Rev 3 – 29 Apr 2015 Page 19
CAE Inc. Confidential and/or Proprietary Information – see title page
3.3.1 Lens Types
The following figures show the different types of GH10 lens available.
Figure 3-9 SONY Lens (Do not remove)
Figure 3-10 CNL (To be transferred to new optical block)
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure Rev 3 – 29 Apr 201 Page 20
CAE Inc. Confidential and/or Proprietary Information – see title page
3.3.2 Detailed Removal Steps
1) Remove Vertical locking mechanism on SONY LENS or CNL. See Figure
3-11.
NOTE: Two types of locking mechanism are available, a vertical locking
or a spring kit mechanism (see Figure 3-12). You do not need to
remove the Spring Kit mechanism.
Figure 3-11 Vertical Locking Mechanism
Figure 3-12 Spring Kit Locking Mechanism
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure
GH10 Optical Block Change Procedure
Rev 3 – 29 Apr 2015 Page 21
CAE Inc. Confidential and/or Proprietary Information – see title page
2) Remove Horizontal locking mechanism on SONY LENS or CNL and put
aside.
Figure 3-13 Horizontal Locking Mechanism
3) Remove FLARING CLAMP on CNL projectors and put aside.
NOTE: Release the two set screws first.
Figure 3-14 Flaring Clamp
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure Rev 3 – 29 Apr 201 Page 22
CAE Inc. Confidential and/or Proprietary Information – see title page
Figure 3-15 Flaring Clamp – Zoom View
4) Remove CNL lens.
NOTE: Hold the lens while removing the four screws.
Figure 3-16 Information Page
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure
GH10 Optical Block Change Procedure
Rev 3 – 29 Apr 2015 Page 23
CAE Inc. Confidential and/or Proprietary Information – see title page
Figure 3-17 Guide Pin Locations
5) Remove CA and CB board.
Figure 3-18 Removing CA and CA Board (1 of 2)
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure Rev 3 – 29 Apr 201 Page 24
CAE Inc. Confidential and/or Proprietary Information – see title page
Figure 3-19 Removing CA and CA Board (2 of 2)
6) Disconnect panel from the board. Remove the board and holder from the
optical block.
Figure 3-20 Removing Board and Holder
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure
GH10 Optical Block Change Procedure
Rev 3 – 29 Apr 2015 Page 25
CAE Inc. Confidential and/or Proprietary Information – see title page
7) Remove optics attachment.
Figure 3-21 Removing Optics Attachment
8) Remove PADS (record location).
Figure 3-22 Removing Pads
9) Remove the three fans.
Figure 3-23 Removing Fans
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure Rev 3 – 29 Apr 201 Page 26
CAE Inc. Confidential and/or Proprietary Information – see title page
3.4 Lamp Power Supply Removal
Remove power supply cover to ease access, harnesses and lamp power supply as per
Service Manual section 1-3-13.
Figure 3-24 Excerpt – Service Manual
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure
GH10 Optical Block Change Procedure
Rev 3 – 29 Apr 2015 Page 27
CAE Inc. Confidential and/or Proprietary Information – see title page
1) Remove power supply cover 2 screws (careful with the retaining clip).
Figure 3-25 Power Supply Cover Removal
2) Remove power supply connectors.
Figure 3-26 Removing Power Supply Connectors
3) Remove connectors from the QA board and red cable retaining clip.
Figure 3-27 Removing Connectors From QA Board
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure Rev 3 – 29 Apr 201 Page 28
CAE Inc. Confidential and/or Proprietary Information – see title page
4) Remove 4 screws retaining plastic power supply cage (G holder). Also, remove
qty 1 screw retaining the metallic support.
Figure 3-28 Screw Removal
5) Remove the assembly and lamp power supply screws (qty 2) + connectors (qty 3).
Figure 3-29 Lamp Power Supply Screws
6) Remove lamp power supply. Remove heat sink retaining clamp
Figure 3-30 Removing Lamp Power Supply
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure
GH10 Optical Block Change Procedure
Rev 3 – 29 Apr 2015 Page 29
CAE Inc. Confidential and/or Proprietary Information – see title page
7) Carefully remove the heat sink protecting the sheet integrity. Install new power
supply and rebuild in the opposite order.
Figure 3-31 Heat Sink Removal
3.5 Projector Rebuild
1) Replace FANS (ensure proper orientation).
2) Replace heat sink pads.
3) Install the optical block spacer and the horizontal lock mechanism (see
Figure 3-32).
4) Reassemble all boards.
5) Refer to the CNL Product Manual, Maintenance and Operation. In the
projector replacement section and perform to the CNL installation
procedures.
6) Install new optical block inside projector.
7) Reassemble projector as per Sony Service Manual.
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure Rev 3 – 29 Apr 201 Page 30
CAE Inc. Confidential and/or Proprietary Information – see title page
Figure 3-32 Horizontal Locking Mechanism
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure
GH10 Optical Block Change Procedure
Rev 3 – 29 Apr 2015 Page 31
CAE Inc. Confidential and/or Proprietary Information – see title page
3.6 Data Upload
The Data Upload procedure is similar to the Data Save procedure (paragraph 3.1)
with NVM procedures. Ensure s/n of optical block and the files from CD are the same
1) Turn projector ON.
2) Connect the RS232 cable to the unit.
3) Start QUICKACCESS and select model VPL-GH10.
Figure 3-33 QuickAccess Window
4) Select LOAD and select proper 3dgm/lut function, see Figure 3-34.
3dgm/lut function in pull down section File name 3DGamma GH10_3DG_xxxxxxx.csv *
LookUpTable GH10_LUT_ xxxxxxx.csv * DDC NOT NEEDED
ABGamma GH10_ABG_ xxxxxxx.csv * LCK GH10_LCK xxxxxxx.csv *
OGMTable GH10_OGM_ xxxxxxx.csv * CSMatrixTable GH10_CSMatrix_ xxxxxxx.csv *
NVM USE the NVM Selection in paragraph 3.6.1. NEVER USE CD supplied version
NOTE: xxxxxxx represents the optical block identifier number (different for each optical block).
* Files are located on the CD provided with the associated optical block.
Figure 3-34 LOAD Selection Chart
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure Rev 3 – 29 Apr 201 Page 32
CAE Inc. Confidential and/or Proprietary Information – see title page
5) Press BROWSE and type a name with the file associated in the function (refer
to LOAD SELECTION CHART, Figure 3-34.
Figure 3-35 Browse, Enter Name
6) Select the proper COM port and baud rate (38400) and press NEXT to proceed.
Figure 3-36 Selecting COM port, Baud Rate
7) Once completed, QUICKACCESS software will automatically quit.
8) Repeat steps 3) to 7), using the next proposed file from the LOAD SELECTION
CHART (see Figure 3-34).
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure
GH10 Optical Block Change Procedure
Rev 3 – 29 Apr 2015 Page 33
CAE Inc. Confidential and/or Proprietary Information – see title page
3.6.1 NVM Selection
The NVM is loaded with a file not supplied on the CD (DO NOT use the NVM file
from the TRAINING or optical block CD)
The file to be used is called nvm_qh9v0102aPatch.csv. It will be supplied on your
computer or you can get it from the STEP 1 article KBID 11063
When the NVM selection is done, select PART and remove the VERIFY selection.
Figure 3-37 Select Part, deselect Verify
1) Select Browse and select nvm_qh9v0102aPatch.csv.
Figure 3-38 Browse, Select
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure Rev 3 – 29 Apr 201 Page 34
CAE Inc. Confidential and/or Proprietary Information – see title page
2) Answer YES to PUSH the new data.
Figure 3-39 Answer Yes To Continue Push
3) Once completed, you will be asked to turn OFF the projector. When the
STANBY LED turns RED, remove the AC power.
Figure 3-40 When STBY LED Turns Red, Remove AC Power
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure
GH10 Optical Block Change Procedure
Rev 3 – 29 Apr 2015 Page 35
CAE Inc. Confidential and/or Proprietary Information – see title page
3.7 Manual Data Modification
The .txt files listed below are available on the SONY CD provided with the optical
block.
NOTE: The information to proceed can also be found in the GH10 Service Manual,
section 1-5-3 TO 1-5-5.
1) Turn projector ON.
2) Make sure the projector is in SERVICE MODE.
3) Select MENU on the projector.
4) Select DEVICE option and select OTHER for the IRIS data change (value
found in IRIS ADJ_VALUE.TXT from the SONY CD).
a. 01 IRIS/ADJ menu set value to 1.
b. 02 IRIS/OPEN REG menu set value as per IRIS ADJ_VALUE.TXT.
c. 03 IRIS/CLOSE REG menu set value as per IRIS ADJ_VALUE.TXT.
d. Go to 01 IRID/ADJ menu and set value to 0.
e. Back to DEVICE menu and select SAVE TO MEMORY.
5) From DEVICE menu, select PANEL DRIVER for the driver gain data change
(value found in GH10_BGAIN.TXT from the SONY CD).
a. Go to 03 P.DRV/GAIN B menu and set value as per GH10_BGAIN.TXT.
b. Back to DEVICE menu and select SAVE TO MEMORY.
6) From DEVICE menu, select DISPLAY ENGINE
a. Go to 06 DE/R REG H menu and set value as per GH10_BGAIN.TXT.
b. 07 DE/R REG V and set value as per GH10_BGAIN.TXT.
c. 08 DE /B REG H and set value as per GH10_BGAIN.TXT.
d. 09 DE/B REG V and set value as per GH10_BGAIN.TXT.
e. Back to DEVICE menu and select SAVE TO MEMORY.
7) From DEVICE menu, select OTHER for the LENS SHIFT data change (value
found in GH10_LENZ_SHIFTDATE_X.TXT).
a. Go to 13 LENS SHIFT/H CENTER menu and set value as per
GH10_LENZ_SHIFTDATE_.TXT.
b. 14 LENS SHIFT/V CENTER menu and set value as per
GH10_LENZ_SHIFTDATE_X.TXT.
c. 15 LENS SHIFT/V TOP menu and set value as per
GH10_LENZ_SHIFTDATE_X.TXT.
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure Rev 3 – 29 Apr 201 Page 36
CAE Inc. Confidential and/or Proprietary Information – see title page
d. 16 LENS SHIFT/V BOTTOM menu and set value as per
GH10_LENZ_SHIFTDATE_X.TXT.
e. 17 LENS SHIFT/ RIGHT menu and set value as per
GH10_LENZ_SHIFTDATE_X.TXT.
f. 18 LENS SHIFT/LEFT menu and set value as per
GH10_LENZ_SHIFTDATE_X.TXT.
g. Back to DEVICE menu and select SAVE TO MEMORY.
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure
GH10 Optical Block Change Procedure
Rev 3 – 29 Apr 2015 Page 37
CAE Inc. Confidential and/or Proprietary Information – see title page
3.8 Projector Settings Update
1) Select MENU.
2) Verify each field to match the following table. Please note the new cooling
settings.
Figure 3-41 Settings Table (1 of 2
SONY Projector VPL-GH10
GH10 Optical Block Change Procedure Rev 3 – 29 Apr 201 Page 38
CAE Inc. Confidential and/or Proprietary Information – see title page
Figure 3-42 Settings Table (2 of 2)
SONY Projector VPL-GH10
Conclusion
Conclusion
Rev 3 – 29 Apr 2015 Page 39
CAE Inc. Confidential and/or Proprietary Information – see title page
4. Conclusion
At the end of the process, access the Information menu (refer to paragraph 2, GH10
Firmware Verification). The projector should display the information as shown
below.
Figure 4-1 Information Page
1) Using the LENS menu, one is able to FOCUS, ZOOM IN AND OUT, LENS
SHIFT up/down and left/right (ensure no locking mechanism is in place).
2) This update is complete; connect the projector to a computer with DVI
connection to display a full HD 1920x1080 image.
3) For CNL projectors, please verify that the BFL is optimal using the CNL
Product Manual, Maintenance and Operation (Typically in projector
replacement section, typically paragraph 2.3.4.2.3).
4) Once everything is completed, please affix the supplied sticker indicating the
180W power supply modification at the location indicated in Figure 4-2.
Figure 4-2 Suggested Sticker Location
top related