SIMULATION AND CONTROL OF A SERIES HYBRID ELECTRIC … · 2013. 7. 2. · 2- Iqbal Husain, “Electric and Hybrid Vehicles Design Fundamentals”, CRC Press LLC, 2003. 3- Iqbal Husain
Post on 14-Mar-2021
3 Views
Preview:
Transcript
REFERENCES 1- Mehrdad Ehsani, Khwaja M. Rahman and Hamid A. Toliyat,
“Propulsion System Design of Electric and Hybrid Vehicles”, IEEE
Transactions on Industrial Electronics, Vol. 44, No. 1, pp. 19-27,
February 1997.
2- Iqbal Husain, “Electric and Hybrid Vehicles Design Fundamentals”,
CRC Press LLC, 2003.
3- Iqbal Husain and Mohammad S. Islam, “Design, Modeling and
Simulation of an Electric Vehicle System”, Society of Automotive
Engineers (SAE), pp. 1-9, 1999 & International Congress and
Exposition, Detroit, Michigon, USA, 1-4 March, 1995.
4- Z. Rahman, M. Ehsani and K. L. Butler, “An Investigation of Electric
Motor Drive Characteristics for EV and HEV Propulsion Systems”,
Society of Automotive Engineers (SAE), pp. 1-8, 2000 & Future
Transportation Technology Conference, Costa Mesa, California, USA,
21-23 August, 2000.
5- P. Andrada, B. Blanqué, J.I. Perat, M. Torrent, E. Martínez and J. A.
Sánchez, “Comparative Efficiency of Switched Reluctance and Induction
Motor Drives for Slowly Varying Loads”, Renewable Energy and Power
Quality Journal, Vol. April 2006, No. 4, pp. 445-449, April 2006.
6- Khwaja M. Rahman, Babak Fahimi, G. Suresh, Anandan Velayutham
Rajarathnam, and M. Ehsani, “Advantages of Switched Reluctance
Motor Applications to EV and HEV: Design and Control Issues”, IEEE
Transactions on Industry Applications, Vol. 36, No. 1, pp. 111-121,
January/February 2000.
255
7- Akira Chiba, Yuichi Takano, Motoki Takeno, Takashi Imakawa,
Nobukazu Hoshi, Masatsugu Takemoto and Satoshi Ogasawara, “Torque
Density and Efficiency Improvements of a Switched Reluctance Motor
Without Rare-Earth Material for Hybrid Vehicles”, IEEE Conference on
Energy Conversion Congress and Exposition (ECCE), pp. 2653-2659,
Atlanta, Georgia, USA, 12-16 September, 2010. & IEEE Transactions on
Industry Applications, Vol. 47, No. 3, pp. 1240-1246, May/June 2011.
8- David G. Dorrell, Andrew M. Knight, Mircea Popescu, Lyndon Evans
and David A. Staton, “Comparison of Different Motor Design Drives for
Hybrid Electric Vehicles”, IEEE Conference on Energy Conversion
Congress and Exposition (ECCE), pp. 3352-3359, Atlanta, Georgia,
USA, 12-16 September, 2010.
9- P.Andrada, M.Torrent, B.Blanqué and J.I.Perat, “Switched Reluctance
Drives for Electric Vehicle Applications”, Department of Electrical
Engineering E.U.P.V.G., Technical University of Catalonia (UPC),
Barcelona, Spain.
10- X. D. Xue, K. W. E. Cheng, and N. C. Cheung, “Selection of Electric
Motor Drives for Electric Vehicles”, Australasian Universities Power
Engineering Conference (AUPEC'08), pp. 1-6, Sydney, Australia, 14-17
December, 2008.
11- Mounir Zeraoulia, Mohamed El Hachemi Benbouzid, and Demba Diallo,
“Electric Motor Drive Selection Issues for HEV Propulsion Systems: A
Comparative Study”, IEEE Transactions on Vehicular Technology, Vol.
55, No. 6, pp. 1756-1764, November 2006.
12- Stephen W. Moore, Khwaja M. Rahman and Mehrdad Ehsani, “Effect on
Vehicle Performance of Extending the Constant Power Region of
Electric Drive Motors”, Society of Automotive Engineers (SAE), pp. 1-
256
5, 1999 & International Congress and Exposition, Detroit, Michigon,
USA, 1-4 March, 1999.
13- Nasser Hashemnia and Behzad Asaei, “Comparative Study of Using
Different Electric Motors in the Electric Vehicles”, Proceedings of the
International conference on Electrical Machines, pp. 1-5, Vilamoura,
Portugal, 6-9 September, 2008.
14- Ali M. Bazzi and Philip T. Krein, “Comparative Evaluation of Machines
for Electric and Hybrid Vehicles Based on Dynamic Operation and Loss
Minimization”, IEEE Conference on Energy Conversion Congress and
Exposition (ECCE), pp. 3345-3351, Atlanta, Georgia, USA, 12-16
September, 2010.
15- J.G.W. West, “DC, Induction, Reluctance and PM Motors for Electric
Vehicles”, IEEE Power Engineering Journal, Vol. 8, No. 2, pp. 77-88,
April 1994.
16- David F. Gosden, “Which Motor for an EV Drive - Induction or PM
AC?”, International Conference on Electrical Machines in Australia
(ICEMA), Vol. 2, Adelaide, South Australia, 14-16 September, 1993.
17- J. Jelonkiewicz and S. Linnman, “Comparative Study of Drives for
Battery Powered Light Vehicles”, 6th European Conference On Power
Electronics And Applications (EPE'95), pp 2895-2900, Sevilla, Spain,
19-21 September, 1995.
18- C.C. Chan and K.T. Chau, “An Overview of the Power Electronics in
Electric Vehicles”, IEEE Transactions on Industrial Electronics, Vol. 44,
No. 1, pp. 3-13, February 1997.
19- R. Krishnan, “Switched Reluctance Motor Drives: Modeling, Simulation,
Analysis, Design, and Applications”, CRC Press LLC, 2001.
257
20- F. Soares and P. J. Costa Branco, “Simulation of a 6/4 Switched
Reluctance Motor Based on Matlab/Simulink Environment”, IEEE
Transactions on Aerospace and Electronic Systems, Vol. 37, No. 3, pp.
989-1009, July 2001.
21- S. Sadeghi, J. Milimonfared and M. Mirsalim, “Dynamic Modeling and
Simulation of a Series Hybrid Electric Vehicle Using a Switched
Reluctance Motor”, IEEE International Conference on Electrical
Machines and Systems (ICEMS), pp. 2017-2022, Seoul, Korea, 8-11
October, 2007.
22- Siavash Sadeghi, Mojtaba Mirsalim and Arash Hassanpour Isfahani,
“Dynamic Modeling and Simulation of a Switched Reluctance Motor in
a Series Hybrid Electric Vehicle”, Acta Polytechnica Hungarica Journal,
Vol. 7, No. 1, pp. 51-71, 2010.
23- Shoichiro Toyoda, “The Electric Vehicle: the Challenge of the Next
Century”, The 13th International Electric Vehicle Symposium (EVS 13),
Vol. 1, pp. 21-24, Osaka, Japan, 13-16 October, 1996.
24- Kaushik Rajashekara, “History of Electric Vehicles in General Motors”,
IEEE Transactions on Industry Applications, Vol. 30, No. 4, pp. 897-
904, July/August 1994.
25- http://www.nissan-zeroemission.com/EN/.
26- http://www.bmw.com/.
27- Hiroshi Shimizu, Junji Harada, Colby Bland, Kiyomoto Kawakami and
Lam Chan, “Advanced Concepts in Electric Vehicle Design”, IEEE
Transactions on Industrial Electronics, Vol. 44, No. 1, pp. 14-18,
February 1997.
28- Masayuki Terashima, Tadashi Ashikaga, Takayuki Mizuno, Kazuo
Natori, Noboru Fujiwara and Masayuki Yada, “Novel Motors and
258
Controllers for High-Performance Electric Vehicle with Four In-Wheel
Motors”, IEEE Transactions on Industrial Electronics, Vol. 44, No. 1, pp.
28-38, February 1997.
29- http://www.ford.com/.
30- http://www.toyota.com/.
31- http://www.gm.com/.
32- http://www.honda.com/.
33- http://www.afdc.energy.gov/afdc/ (the Alternative Fuels and
Advanced Vehicles Data Center (AFDC) ).
34- James Larminie and John Lowry, “Electric Vehicle Technology
Explained”, John Wiley & Sons Ltd, 2003.
35- Mehrdad Ehsani, Yimin Gao, Sebastien E. Gay and Ali Emadi, “Modern
Electric, Hybrid Electric, and Fuel Cell Vehicles Fundamentals, Theory,
and Design”, CRC Press LLC, 2005.
36- D.Assanis, G. Delagrammatikas, R. Fellini, Z. Filipi, J. Liedtke, N.
Michelena, P. Papalambros, D. Reyes, D. Rosenbaum, A. Sales and M.
Sasena, “An Optimization Approach to Hybrid Electric Propulsion
System Design”, Mechanics of Structures and Machines, Vol. 27, No. 4,
pp. 393-421, 1999.
37- Mark Alexander, Thomas Bradley, Brian Huff, Peter Hutchison, Robert
Kamisky Greg Loomis, Samantha McMahon, Nathaniel Meyr, Robert
Schurhoff, James Vaughn, Mark Duvall, and Andrew Frank, “Design
and Development of the UC Davis Future Truck”, UC Davis Hybrid
Electric Vehicle Center, pp. 1-13.
38- Takeo S. Saitoh, Noboru Yamada, Daigo Ando and Kazuyoshi Kurata,
“A Grand Design of Future Electric Vehicle to Reduce Urban Warming
259
and CO2 Emissions in Urban Area”, Renewable Energy, No. 30, pp.
1847-1860, 2005 (www.sciencedirect.com).
39- Atsuo Kawamura, Nobukazu Hoshi, Tae Woong Kim, Tomoki
Yokoyama and Tsuneo Kume, “Analysis of Anti-Directional-Twin-
Rotary Motor Drive Characteristics for Electric Vehicles”, IEEE
Transactions on Industrial Eectronics, Vol. 44, No. 1, pp. 64-70,
February 1997.
40- Walter Janach, “Ultralight Electric Vehicle for Urban Mass
Transportation”, IEEE Vehicle Power and Propulsion Conference
(VPPC), pp. 1-4, Harbin, China, 3-5 September, 2008.
41- Andrzej M. Trzynadlowski, Zhiqiang Wang, James M. Nagashima,
Costin Stancu and Marcin H. Zelechowski, “Comparative Investigation
of PWM Techniques for a New Drive for Electric Vehicles”, IEEE
Transactions on Industry Applications, Vol. 39, No. 5, pp. 1396-1403,
September/October 2003.
42- Mehrdad Ehsani, Khwaja M. Rahman, Maria D. Bellar, and Alex J.
Severinsky, “Evaluation of Soft Switching for EV and HEV Motor
Drives”, IEEE Transactions on Industrial Electronics, Vol. 48, No. 1,
pp. 82-90, February 2001.
43- John G. Hayes, Michael G. Egan, John M. D. Murphy, Steven E. Schulz
and John T. Hall, “Wide-Load-Range Resonant Converter Supplying the
SAE J-1773 Electric Vehicle Inductive Charging Interface”, IEEE
Transactions on Industry Applications, Vol. 35, No. 4, July/August 1999.
44- Martin J. Hoeijmakers and Jan A. Ferreira, “The Electric Variable
Transmission”, IEEE Transactions on Industry Applications, Vol. 42,
No. 4, pp. 1092-1100, July/August 2006.
260
45- Xi Jun-qiang, Xiong Guang-ming and Zhang Yan, “Application of
Automatic Manual Transmission Technology in Pure Electric Bus”,
IEEE Vehicle Power and Propulsion Conference (VPPC), pp. 1-4,
Harbin, China, 3-5 September, 2008.
46- Guo Xinhua, Wen Xuhui, Chen Jingwei, Zhao Feng and Guo Xizheng,
“Simulation of an Electrical Variable Transmission Based on Dual
Mechanical Ports Electric Machine with Clutch”, IEEE Vehicle Power
and Propulsion Conference (VPPC), pp. 1-5, Harbin, China, 3-5
September, 2008.
47- Jin-uk Jeong, Hyeoun-dong Lee, Chul-soo Kim,Hang-Seok Choi and Bo-
Hyung Cho, “A Development of an Energy Storage System for Hybrid
Electric Vehicles Using Supercapacitor”, The 19th International Electric
Vehicle Symposium (EVS 19), pp. 1379-1389, Busan, South Korea, 19-
23 October, 2002.
48- Sandeep Dhameja, “Electric Vehicle Battery Systems”, Butterworth–
Heinemann, 2002.
49- D. Corrigan, I. Menjak, B. Cleto, S. Dhar, S. Ovshinsky and A. Frank,
“Nickel-Metal Hydride Batteries For ZEV-Range Hybrid Electric
Vehicles”, Ovonic Battery Company, Troy, Michigan, USA, pp. 1-12.
50- Seung-Ki Sul and Sang-Joon Lee, “An Integral Battery Charger for Four-
Wheel Drive Electric Vehicle”, IEEE Transactions on Industry
Applications, Vol. 31, No. 5, September/ October 1995.
51- Alireza Khaligh, and Zhihao Li, “Battery, Ultracapacitor, Fuel Cell,
Hybrid Energy Storage Systems for Electric, Hybrid Electric, Fuel Cell,
and Plug-in Hybrid Electric Vehicles: State of the Art”, IEEE
Transactions on Vehicular Technology, Vol. 59, No. 6, pp. 2806-2814,
July 2010.
261
52- A. Cooper, “Development of a Lead-Acid Battery For a Hybrid Electric
Vehicle”, Journal of Power Sources, No. 133, pp. 116-125, 2004
(www.sciencedirect.com).
53- Paul Atwood, Stephen Gurski and Douglas J.Nelson, “Degree of
Hybridization Modeling of a Fuel Cell Hybrid Electric Sport Utility
Vehicle”, Society of Automotive Engineers, pp. 1-8, 2001.
54- Andreas Schell, Huei Peng, Doanh Tran, Euthie Stamos, Chan-Chiao Lin
and Min Joong Kim, “Modelling and Control Strategy Development for
Fuel Cell Electric Vehicles”, Annual Reviews in Control, No. 29, pp.
159-168, 2005 (www.sciencedirect.com).
55- Karen L. Butler, Mehrdad Ehsani and Preyas Kamath, “A Matlab-Based
Modeling and Simulation Package for Electric and Hybrid Electric
Vehicle Design”, IEEE Transactions on Vehicular Technology, Vol. 48,
No. 6, pp.1770-1778, November 1999.
56- Johanna Wallen, “Modelling of Components for Conventional Car and
Hybrid Electric Vehicle in Modelica”, Master's thesis, 10th May 2004.
57- Leo Laine and Johan Andreasson, “Modelling of Generic Hybrid Electric
Vehicles”, 3rd international modelica conference, pp. 87-94, Linkoping,
Sweden, 3-4 November, 2003.
58- K. Wipke, M. Cuddy, D. Bharathan, S. Burch, V. Johnson, A. Markel,
and S. Sprik, “Advisor 2.0: A Second- Generation Advanced Vehicle
Simulator for Systems Analysis”, National Renewable Energy
Laboratory (NREL), March 1999, Presented at the North American EV
& Infrastructure Conference and Exposition (NAEVI 98), Phoenix,
Arizona, USA, 3-4 December, 1998.
59- Randall Donn Senger, “Validation of Advisor as a Simulation Tool for a
Series Hybrid Electric Vehicle Using the Virginia Tech Future Car
262
Lumina”, Master Thesis, Submitted to Faculty of Virginia Polytechnic
Institute, State University, Blacksburg, Virginia, 18 September, 1997.
60- Bimal K. Bose, and Paul M. Szczesny, “A Microcomputer-Based
Control and Simulation of an Advanced IPM Synchronous Machine
Drive System for Electric Vehicle Propulsion”, IEEE Transactions on
Industrial Electronics, Vol. 35, No. 4, pp. 547-558, November 1988.
61- Matthew Alan Merkle, “Variable Bus Voltage Modeling for Series
Hybrid Electric Vehicle Simulation”, Master Thesis, Virginia
Polytechnic Institute and State University, Blacksburg, Virginia, 1
December, 1997.
62- Giorgio Rizzoni, Lino Guzzella and Bernd M. Baumann, “Unified
Modeling of Hybrid Electric Vehicle Drivetrains”, IEEE/ASME
Transactions on Mechatronics, Vol. 4, No. 3, pp. 246-257, September
1999.
63- T.H. Tran, Q.P. Ha, R. Grover and S. Scheding, “Modelling of an
Autonomous Amphibious Vehicle”, Proceedings of the Australasian
Conference on Robotics & Automation, Canberra, Australia, pp. 1-7, 6 -
8 December, 2004.
64- Nobuyoshi Mutoh, Satoru Kaneko, Taizou Miyazaki, Ryosou Masaki
and Sanshiro Obara, “A Torque Controller Suitable for Electric
Vehicles”, IEEE Transactions on Industrial Electronics, Vol. 44, No. 1,
pp. 54-63, February 1997.
65- Yoichi Hori, Yasushi Toyoda and Yoshimasa Tsuruoka, “Traction
Control of Electric Vehicle: Basic Experimental Results Using the Test
EV “UOT Electric March””, IEEE Transactions on Industry applications,
Vol. 34, No. 5, pp. 1131-1138, September/October 1998.
263
66- Li Weili,Sheng Man and Huo Fei, “Optimal design and Finite Element
Analysis of Switched Reluctance Motor for Electric Vehicles”, IEEE
Vehicle Power and Propulsion Conference (VPPC), pp. 1-5, Harbin,
China, 3-5 September 2008.
67- Shyam S. Ramamurthy and Juan Carlos Balda, “Sizing a Switched
Reluctance Motor for Electric Vehicles”, IEEE Transactions on Industry
Applications, Vol. 37, No. 5, pp. 1256-1264, September/October 2001.
68- Wei Cai, Pragasen Pillay, Zhangjun Tang and Avoki M. Omekanda,
“Low-Vibration Design of Switched Reluctance Motors for Automotive
Applications Using Modal Analysis”, IEEE Transactions on Industry
Applications, Vol. 39, No. 4, pp. 971-977, July/August 2003.
69- T. J. E. Miller, “Optimal Design of Switched Reluctance Motors”, IEEE
Transactions on Industry Applications, Vol. 49, No. 1, pp. 15-27,
February 2002.
70- Tatsuya Uematsu and Richard S. Wallace, “Design of a 100 Kw
Switched Reluctance Motor for Electric Vehicle Propulsion”, IEEE
Applied Power Electronics Conference and Exposition (APEC), pp. 411-
415, Texas, USA, 5-9 March 1995.
71- S. Kachapornkul, P. Jitkreeyarn, P. Somsiri and K. Tungpimolrut, “A
Design of 15 Kw Switched Reluctance Motor for Electric Vehicle
Applications”, Proceeding of International Conference on Electrical
Machines and Systems, pp. 1690-1693, Seoul, Korea, 8-11 October,
2007.
72- Shuanghong Wang, Qionghua Zhan, Zhiyuan Ma, and Libing Zhou,
“Implementation of a 50-kW Four-Phase Switched Reluctance Motor
Drive System for Hybrid Electric Vehicle”, IEEE Transactions on
Magnetics, Vol. 41, No. 1, pp. 501-504, January 2005.
264
73- W Wu, H C Lovatt, and J B Dunlop, “Optimisation of Switched
Reluctance Motors for Hybrid Electric Vehicles”, IEEE International
Conference on Power Electronics, Machines and Drives, pp. 177-182, University of Bath, venue, United Kingdom, 4-7 June, 2002.
74- Jiongkang Lin, K.W. Eric Cheng, Zhu Zhang and Xiangdang Xue,
“Experimental Investigation of In-wheel Switched Reluctance Motor
Driving System for Future Electric Vehicles”, IEEE 3rd International
Conference on Power Electronics Systems and Applications (PESA), pp.
1-6, Hong Kong, Hong Kong, 20-22 May, 2009.
75- P.C.K. Luk and P. Jinupun, “An In-Wheel Switched Reluctance Motor
for Electric Vehicles”, IEEE 5th International Power Electronics and
Motion Control Conference (IPEMC), pp. 1-5, Beijing, China, 14-16
August, 2006.
76- Shumei Cui, Yongjie Yuan and Tiecheng Wang, “Research on Switched
Reluctance Double-rotor Motor Used for Hybrid Electric Vehicle”, IEEE
International Conference on Electrical Machines and Systems (ICEMS),
pp. 3393-3396, Wuhan, China, 17-20 October, 2008.
77- M. Majchrowicz and W. Jazdzynski, “Selected Problems of Optimization
of a Switched Reluctance Motor for an Electric Vehicle using Analytical
Calculations”, International Conference on Renewable Energies and
Power Quality (ICREPQ’10), Granada, Spain, 23-25 March, 2010.
78- Wieslaw Jazdzynski, and Michal Majchrowicz, “An Approach to Find an
Optimum Designed SRM for Electric Vehicle Drive”, Proceedings of the
18th IEEE International Conference on Electrical Machines (ICEM), pp.
1-6, Vilamoura, Portugal, 6-9 Septamber, 2008.
79- Piyush C. Desai, Mahesh Krishnamurthy, Nigel Schofield and Ali
Emadi, “Novel Switched Reluctance Machine Configuration With
265
Higher Number of Rotor Poles Than Stator Poles: Concept to
Implementation”, IEEE Transactions on Industrial Electronics, Vol. 57,
No. 2, pp. 649-659, February 2010.
80- Tsarafidy Raminosoa, Benjamin Blunier, Daniel Fodorean and Abdellatif
Miraoui, “Design and Optimization of a Switched Reluctance Motor
Driving a Compressor for a PEM Fuel-Cell System for Automotive
Applications”, IEEE Transactions on Industrial Electronics, Vol. 57, No.
9, pp. 2988-2997, September 2010.
81- X. D. Xue, K.W. E. Cheng, T.W. Ng, and N. C. Cheung, “Multi-
Objective Optimization Design of In-Wheel Switched Reluctance Motors
in Electric Vehicles”, IEEE Transactions on Industrial Electronics, Vol.
57, No. 9, pp. 2980-2987, September 2010.
82- Berker Bilgin, Ali Emadi and Mahesh Krishnamurthy, “Design
Considerations for Switched Reluctance Machines with Higher Number
of Rotor Poles”, IEEE Transactions on Industrial Electronics, Vol. PP,
No. 99, pp. 1-11, April 2011.
83- Khwaja M. Rahman and Steven E. Schulz, “Design of High-Efficiency
and High Torque-Density Switched Reluctance Motor for Vehicle
Propulsion”, IEEE Transactions on Industry Applications, Vol. 38, No.
6, pp. 1500-1507, November/December 2002.
84- Shyam S. Ramamurthy and Juan Carlos Balda, “The Power Ratings of an
Electric Motor for Electric Vehicles”, Department of Electrical
Engineering, University of Arkansas, Final Report Prepared for Office of
Naval Research, Arlington, July 1999.
85- Avoki M. Omekanda, “A New Technique for Multidimensional
Performance Optimization of Switched Reluctance Motors for Vehicle
266
Propulsion”, IEEE Transactions on Industry Applications, Vol. 39, No.
3, pp. 672-676, May/June 2003.
86- M. A. Cinar and F. Erfan Kuyumcu, “Design and Drives Simulation of
an In-Wheel Switched Reluctance Motor for Electric Vehicle
Applications”, IEEE International Electric Machines & Drives
Conference (IEMDC '07), pp. 50-54, Antalya, Turkey, 3-5 May, 2007.
87- Wang yan, Yin Tian-ming and Ren fei, “The Research of 30 Kw Electric
Vehicle Drive System Based on SRM”, IEEE Vehicle Power and
Propulsion Conference (VPPC), pp. 1-6, Harbin, China, 3-5 September,
2008.
88- Pragasen Pillay, and William (Wei) Cai, “An Investigation into Vibration
in Switched Reluctance Motors”, IEEE Transactions on Industry
Applications, Vol. 35, No. 3, pp. 589-596, May/June 1999.
89- Chi-Yao Wu and Charles Pollock, “Analysis and Reduction of Vibration
and Acoustic Noise in the Switched Reluctance Drive”, IEEE
Transactions on Industry Applications, Vol. 31, No. 1, pp. 91-98,
January/February 1995.
90- Nesimi Ertugrul and Adrian D. Cheok, “Indirect Angle Estimation in
Switched Reluctance Motor Drives Using Fuzzy Logic Based Motor
Model”, IEEE Transactions on Power Electronics, Vol. 15, No. 6, pp.
1029-1044, November 2000.
91- Mehrdad Ehsani and Babak Fahimi, “Elimination of Position Sensors in
Switched Reluctance Motor Drives: State of the Art and Future Trends”,
IEEE Transactions on Industrial Electronics, Vol. 49, No. 1, pp. 40-47,
February 2002.
92- Kristof R. Geldhof, Alex P. M. Van den Bossche and Jan A. Melkebeek,
“Rotor-Position Estimation of Switched Reluctance Motors Based on
267
Damped Voltage Resonance”, IEEE Transactions on Industrial
Electronics, Vol. 57, No. 9, pp. 2954-2960, September 2010.
93- O. Cornea and D. Popovici, “Software Position Tuning of a SRM Drive
System”, The 12th IEEE International Conference on Optimization of
Electrical and Electronic Equipment (OPTIM), pp. 520 -525, Brasov,
Romania, 20-22 May, 2010.
94- Lei Shen, Jianhua Wu and Shiyou Yang , “Initial Position Estimation in
SRM Using Bootstrap Circuit Without Predefined Inductance
Parameters”, IEEE Transactions on Power Electronics, Vol. 26, No. 9,
pp. 2449-2456, September 2011.
95- Gregory Pasquesoone and Iqbal Husain, “Position Estimation at Starting
and Lower Speed in Three-Phase Switched Reluctance Machines Using
Pulse Injection and Two Thresholds”, IEEE Conference on Energy
Conversion Congress and Exposition (ECCE), pp. 2660-2666, Atlanta,
Georgia, USA, 12-16 September, 2010.
96- Keunsoo Ha, Rae-Young Kim and Krishnan Ramu, “Position Estimation
in Switched Reluctance Motor Drives using the First Switching
Harmonics through Fourier Series”, IEEE Transactions on Industrial
Electronics, Vol. 58, No. 12, pp. 5352-5360, December 2011.
97- S. Misawa and I. Miki, “A Rotor Position Estimation Using Fourier
Series of Phase Inductance for Switched Reluctance Motor”, IEEE
International Symposium on Power Electronics Electrical Drives
Automation and Motion (SPEEDAM), pp. 1259 -1263, Pisa, Italy, 14-16
June, 2010.
98- Oguz Ustun and Erdal Bekiroglu, “Modeling and Simulation of Position
Estimation of Switched Reluctance Motor with Artificial Neural
268
Networks”, World Academy of Science, Engineering and Technology
(WASET) Journal, Vol. 3, No. 33, pp. 30-34, September 2009.
99- T. W. Ching, “Soft-switching Converters for Electric Vehicle
Propulsion”, Journal of Asian Electric Vehicles, Vol. 5, No. 2, pp. 1019-
1026, December 2007.
100- Jianing Liang, Dong-Hee Lee, Guoqing Xu and Jin-Woo Ahn,
“Analysis of Passive Boost Power Converter for Three-Phase SR
Drive”, IEEE Transactions on Industrial Electronics, Vol. 57, No. 9, pp.
2961-2971, September 2010.
101- Slobodan Vukosavic and Victor R. Stefanovic, “SRM Inverter
Topologies: A Comparative Evaluation”, IEEE Transactions on Industry
Applications, Vol. 27, No. 6, pp. 1034-1047, November/December
1991.
102- P. Somsiri, K. Tungpimonrut and P. Aree , “Three-Phase Full-Bridge
Converters Applied to Switched Reluctance Motor Drives with a
Modified Switching Strategy”, IEEE International Conference on
Electrical Machines and Systems (ICEMS), pp. 1563-1568, Los
Alamitos, California, USA, 8-11 October, 2007.
103- T. W. Ching, K. T. Chau and C. C. Chan, “A New Zero-Voltage-
Transition Converter for Switched Reluctance Motor Drives”, The 29th
IEEE International Conference on Power Electronics Specialists
(PESC), pp. 1295 -1301, Fukuoka, Japan, 17-22 May, 1998.
104- S. Sadeghi, J. Milimonfared, M. Mirsalim and M. Jalalifar, “Dynamic
Modeling and Simulation of a Switched Reluctance Motor in Electric
Vehicles”, 1st IEEE International Conference on Industrial Electronics
and Applications (ICIEA), pp. 1-6, Singapore, 24-26 May, 2006.
269
105- X. D. Xue, J. K. Lin, Z. Zhang, T. W. Ng, K. F. Luk, K. W. E. Cheng
And N. C. Cheung, “Study of Motoring Operation of In-wheel Switched
Reluctance Motor Drives for Electric Vehicles”, 3rd IEEE International
Conference on Power Electronics Systems and Applications (PESA),
pp. 1-6, 20-22 May, 2009.
106- K. Watanabe, S. Aida, A. Komatsuzaki and I. Miki, “Driving Force
Characteristics of 40Kw Switched Reluctance Motor for Electric
Vehicle”, IEEE International Conference on Electrical Machines and
Systems (ICEMS), pp. 1894-1898, Seoul, Korea, 8-11 October, 2007.
107- K. I. Hwu, “Applying Powersys and Simulink to Modeling Switched
Reluctance Motor”, Tamkang Journal of Science and Engineering, Vol.
12, No. 4, pp. 429-438, 2009.
108- X. D. Xue, K. W. E. Cheng, T. W. Ng, and N. C. Cheung, “Investigation
on Characteristics of Braking Operation of Switched Reluctance Motor
Drives for Electric Vehicles”, Australasian Universities Power
Engineering Conference (AUPEC'08), pp. 1-6, Sydney, Australia, 14-17
December, 2008.
109- Satoshi Aida, Akitomo Komatsuzaki and Ichiro Miki, “Basic
Characteristics of Electric Vehicle Using 40kW Switched Reluctance
Motor”, IEEE International Conference on Electrical Machines and
Systems (ICEMS), pp. 3358-3361, Wuhan, China, 17-20 October, 2008.
110- Vikas S. Wadnerkar, Dr. G. TulasiRam Das and Dr. A.D.Rajkumar,
“Performance Analysis of Switched Reluctance Motor; Design,
Modeling and Simulation of 8/6 Switched Reluctance Motor”, Journal
of Theoretical and Applied Information Technology (JATIT), Vol. 4,
No. 11, pp. 1118-1124, 2005.
270
111- X. D. Xue, K. W. E. Cheng and N. C. Cheung, “Evaluation of Torque
Sharing Functions for Torque Ripple Minimization of Switched
Reluctance Motor Drives in Electric Vehicles”, Australasian
Universities Power Engineering Conference (AUPEC'08), pp. 1-6,
Sydney, Australia, 14-17 December, 2008.
112- Shoujun Song and Weiguo Liu, “A Comparative Study on Modeling
Methods for Switched Reluctance Machines”, Computer and
Information Science Journal, Vol. 3, No. 2, pp. 205-210, May 2010.
113- Christophe Roux and Medhat M. Morcos, “On the Use of a Simplified
Model for Switched Reluctance Motors”, IEEE Transactions on Energy
Conversion, Vol. 17, No. 3, pp. 400-405, September 2002.
114- Vladan Vujicic and Slobodan N. Vukosavic, “A Simple Nonlinear
Model of the Switched Reluctance Motor”, IEEE Transactions on
Energy Conversion, Vol. 15, No. 4, pp. 395-400, December 2000.
115- J. D. Ferreira Rodríguez and A. C. Renfrew, “Modeling of a Switched
Reluctance Drive System for a ‘Convoy Vehicle’”, IEEE International
Electric Machines & Drives Conference (IEMDC '05), pp. 1535-1541,
San Antonio, Texas, USA, 5-15 May, 2005.
116- Huijun Zhou, Wen Ding and Zhenmin Yu, “A Nonlinear Model for the
Switched Reluctance Motor”, IEEE Eighth International Conference on
Electrical Machines and Systems (ICEMS), pp. 568-571, Nanjing,
China, 27-29 September, 2005.
117- Peng Zhang, Pablo A. Cassani and Sheldon S. Williamson, “An
Accurate Inductance Profile Measurement Technique for Switched
Reluctance Machines”, IEEE Transactions on Industrial Electronics,
Vol. 57, No. 9, pp. 2972-2979, September 2010.
271
118- Emil Pădurariu, Liviu Somesan, Ioan-Adrian Viorel, Claudia Steluta
Martis and Octavian Cornea, “Switched Reluctance Motor Analytical
Models, Comparative Analysis”, The 12th IEEE International
Conference on Optimization of Electrical and Electronic Equipment
(OPTIM), pp. 285 -290, Brasov, Romania, 20-22 May, 2010.
119- Hamid Ehsan Akhter, Virendra K. Sharma1, A. Chandra, and Kamal Al-
Haddad, “Performance Simulation of Switched Reluctance Motor Drive
System Operating With Fixed Angle Control Scheme”, The 7th
International Conference on Modeling and Simulation of Electric
Machines, Converters and Systems (Electrimacs), pp. 1 -7, Montreal,
Canada, 18-21 August, 2002.
120- Iqbal Husain and Mohammad S. Islam, “Design, Modeling and
Simulation of an Electric Vehicle System”, Society of Automotive
Engineers (SAE), pp. 1-9, 1999 & International Congress and
Exposition, Detroit, Michigon, USA, 1-4 March, 1995.
121- Jinhui Zhang and Arthur V. Radun, A.V. , “A Simplified Analytical
Flux Model of Switched Reluctance Motor”, IEEE International Electric
Machines & Drives Conference (IEMDC '05), pp. 510-515, San
Antonio, Texas, USA, 5-15 May, 2005.
122- Hamid Ehsan Akhter, Virendra K. Sharma; Ambrish Chandra and
Kamal Al-Haddad , “Modeling Simulation and Performance Analysis of
Switched Reluctance Motor Operating with Optimum Value of Fixed
Turn-on And Turn-off Switching Angles”, The 34th IEEE International
Conference on Power Electronics Specialists (PESC), pp. 397 -402,
Acapulco, Mexico, 15-19 June, 2003.
123- Wei Min Chan and W.F.Weldon, “Development of a Simple Nonlinear
Switched Reluctance Motor Model Using Measured Flux Linkage Data
272
and Curve Fit”, IEEE 32nd Industry Applications Conference (IAS), pp.
318-325, New Orleans, Louisiana, USA, 5-9 October, 1997.
124- Yongli Zhao, Yuhong Zhang, and Yane Zhao, “Stability Control System
for Four-In-Wheel-Motor Drive Electric Vehicle”, Sixth International
Conference on Fuzzy Systems and Knowledge Discovery, pp. 171-175,
Tianjin, China, 14-16 August, 2009.
125- Yu Lei-yan and Yun Ping-li, “Motor Motion Control of Automobile
Steer-by-wire System in Electric Vehicles”, IEEE Conference on
Vehicle Power and Propulsion (VPPC), pp. 1502-1505, Dearborn,
Michigan, USA, 7-10 September, 2009.
126- Li Feiqiang, Wang Jun and Liu Zhaodu, “Motor Torque Based Vehicle
Stability Control for Four-wheel-drive Electric Vehicle”, IEEE
Conference on Vehicle Power and Propulsion (VPPC), pp. 1596-1601,
Dearborn, Michigan, USA, 7-10 September, 2009.
127- Domenico Casadei, Michele Mengoni, Giovanni Serra, Angelo Tani,
and Luca Zarri, “A Control Scheme with Energy Saving and DC-Link
Overvoltage Rejection for Induction Motor Drives of Electric Vehicles”,
IEEE Transactions on Industry Applications, Vol. 46, No. 4, pp. 1436-
1446, July/August 2010.
128- Ricardo de Castro, Rui Esteves Araújo and Hugo Oliveira, “Design,
Development and Characterisation of a FPGA Platform for Multi-Motor
Electric Vehicle Control”, IEEE Conference on Vehicle Power and
Propulsion (VPPC), pp. 145-152, Dearborn, Michigan, USA, 7-10
September, 2009.
129- Chen Ze-Yu and Zhang Cheng-Ning, “Control Strategy for Steering in
Braking Process of Dual-motor Electric Tracked Vehicle”, Asia-Pacific
273
Conference on Power and Energy Engineering (APPEEC), pp. 1-5,
SiChuan, China, 28-31 March, 2010.
130- Ricardo de Castro, Rui Esteves Araujo, Hugo Oliveira, “Control in
Multi-Motor Electric Vehicle with a FPGA Platform”, IEEE
International Symposium on Industrial Embedded Systems (SIES), pp.
219-227, Lausanne, Switzerland, 8-10 July, 2009.
131- Dongyun Lu and Narayan C. Kar, “Neural Network Based Torque
Control of Switched Reluctance Motor for Hybrid Electric Vehicle
Propulsion at High Speeds”, IEEE Electrical Power & Energy
Conference (EPEC), pp. 1-6, Montreal, Quebec, Canada, 22-23 October,
2009.
132- Dongyun Lu and Narayan C. Kar, “Neural Network Based Torque
Control of Switched Reluctance Motor for Hybrid Electric Vehicle
Propulsion at Low Speeds”, IEEE International Conference on
Electro/Information Technology (EIT '09), pp. 417- 422, Windsor,
Ontario, Canada, 7-9 June, 2009.
133- M.G.Rodrigues, W. I. Suemitsu, P.Branco, J.A.Dente and L.G.B.Rolim,
“Fuzzy Logic Control of a Switched Reluctance Motor”, IEEE
International Symposium on Industrial Electronics (ISIE '97), pp. 527-
531, Guimaraes, Portugal, 7-11 July, 1997.
134- Yun-hong Zheng and De-an Zhao, “Study on Operation of Switched
Reluctance Motor for Electric Vehicles Based on FPGA”, IEEE
International Conference on Information Management, Innovation
Management and Industrial Engineering (ISIE '97), pp. 512-516, Xian,
China, 26-27 December, 2009.
135- Yu-Long Cui, Jiao-Min Liu and Xue-Chuan Hou, “A Control Solution
for Electric Vehicle Driver with Switched Reluctance Motor”,
274
Proceedings of the IEEE International Conference on Robotics,
Intelligent Systems and Signal Processing, Changsha, China, pp. 531-
536, October 2003.
136- Nattapon Chayopitak, Ruchao Pupadubsin, Kanokvate Tungpimolrut,
Pakasit Somsiri, Prapon Jitkreeyan and Suebsuang Kachapornkul, “An
Adaptive Low-Ripple Torque Control of Switched Reluctance Motor for
Small Electric Vehicle”, IEEE International Conference on Electrical
Machines and Systems (ICEMS), pp. 3327-3332, Wuhan, China, 17-20
October, 2008.
137- GAO Yuan, “Speed Control of Switched Reluctance Motors”, Master
Thesis, Submitted to Department of Electrical and Electronic
Engineering, Hong Kong University of Science and Technology, August
2000.
138- Ahmed Tahour, Abdelkader Meroufel, Hamza Abid and Abdel Ghani
Aissaoui, “Sliding Controller of Switched Reluctance Motor”, Leonardo
Electronic Journal of Practices and Technologies, Issue 12, pp. 151-162,
January/June 2008.
139- N. C. Sahoo, J. X. Xu and S. K. Panda, “Low Torque Ripple Control of
Switched Reluctance Motors Using Iterative Learning”, IEEE
Transactions on Energy Conversion, Vol. 16, No. 4, pp. 318-326,
December 2001.
140- Khwaja M. Rahman and Steven E. Schulz, “High-Performance Fully
Digital Switched Reluctance Motor Controller for Vehicle Propulsion”,
IEEE Transactions on Industry Applications, Vol. 38, No. 4, pp. 1062-
1071, July/August 2002.
141- Steven E. Schulz and Khwaja M. Rahman, “High-Performance Digital
PI Current Regulator for EV Switched Reluctance Motor Drives”, IEEE
275
37th Industry Applications Conference (IAS), pp. 1617-1624, Pittsburgh,
Pennsylvania, USA, 13-18 October, 2002 & IEEE Transactions on
Industry Applications, Vol. 39, No. 4, pp. 1118-1126, July/August 2003.
142- Yuefeng Yang and Tihuang Zhang, “Sliding Mode-PI Control of
Switched Reluctance Motor Drives For EV”, Proceedings of the IEEE
Eighth International Conference on Electrical Machines and Systems
(ICEMS), pp. 603-607, Nanjing, China, 27-29 September, 2005.
143- Ayumu Nishimiya, Hiroki Goto, Hai-Jiao Guo and Osamu Ichinokura,
“A Novel Torque Control for a SR Motor EV”, Proceedings of the 18th
IEEE International Conference on Electrical Machines (ICEM), pp. 1-5,
Vilamoura, Portugal, 6-9 Septamber, 2008.
144- Christos Mademlis and Iordanis Kioskeridis, “Gain-Scheduling
Regulator for High-Performance Position Control of Switched
Reluctance Motor Drives”, IEEE Transactions on Industrial Electronics,
Vol. 57, No. 9, pp. 2922-2931, September 2010.
145- Srdjan M. Lukic and Ali Emadi, “State-Switching Control Technique
for Switched Reluctance Motor Drives: Theory and Implementation”,
IEEE Transactions on Industrial Electronics, Vol. 57, No. 9, pp. 2932-
2938, September 2010.
146- X. D. Xue, K. W. E. Cheng, J. K. Lin, Z. Zhang, K. F. Luk, T. W. Ng,
and N. C. Cheung, “Optimal Control Method of Motoring Operation for
SRM Drives in Electric Vehicles”, IEEE Transactions on Vehicular
Technology, Vol. 59, No. 3, pp. 1191-1204, March 2010.
147- Shun-Chung Wang and Yi-Hwa Liu, “A Modified PI-Like Fuzzy Logic
Controller for Switched Reluctance Motor Drives”, IEEE Transactions
on Industrial Electronics, Vol. 58, No. 5, pp. 1812-1825, May 2011.
276
148- H. Naitoh and H. Ishikawa, “A Current Controller for a Switched
Reluctance Motor Based on Model Reference Adaptive Control”,
International Symposium on Power Electronics, Electrical Drives,
Automation and Motion (SPEEDAM), pp. 1270-1275, Pisa, Italy, 14-16
June, 2010.
149- S. Sedghizadeh, C. Lucas and H. Ghafoori Fard, “Sensorless Speed
Control of Switched Reluctance Motor Drive Using the Binary Observer
with Online Flux-Linkage Estimation”, Iranian Journal of Electrical &
Electronic Engineering, Vol. 5, No. 2, pp. 143-150, January 2009.
150- Robert B. Inderka, Marcus Menne and Rik W. A. A. De Doncker,
“Control of Switched Reluctance Drives for Electric Vehicle
Applications”, IEEE Transactions on Industrial Electronics, Vol. 49, No.
1, pp. 48-53, February 2002.
151- Robert B. Inderka and Rik W. A. A. De Doncker, “High-Dynamic
Direct Average Torque Control for Switched Reluctance Drives”, IEEE
Transactions on Industry Applications, Vol. 39, No. 4, pp. 1040-1045,
July/August 2003.
152- Dejun Yin, Sehoon Oh and Yoichi Hori, “A Novel Traction Control for
EV Based on Maximum Transmissible Torque Estimation”, IEEE
Transactions on Industrial Electronics, Vol. 56, No. 6, pp. 2094-2086,
June 2009.
153- Xiaoling Yuan, Yimin Gao and M. Ehsani, “Study on the Performance
and Control of SR Machine for Vehicle Regenerative Braking”, IEEE
Vehicle Power and Propulsion Conference (VPPC), pp. 1-5, Harbin,
China, 3-5 September, 2008.
154- MATLAB 7.5, The Mathworks Inc., 15 August 2007.
277
155- A. E. Fitzgerald, Charles Kingsley, Jr. and Stephen D. Umans, “Electric
Machinery, Sixth Edition”, McGraw-Hill, 2003.
278
top related