Panasonic TH-42PH9E Service Manual
Post on 16-Nov-2015
278 Views
Preview:
DESCRIPTION
Transcript
2006 Matsushita Electric Industrial Co., Ltd. Allrights reserved. Unauthorized copying anddistribution is a violation of law.
TH-42PH9BKTH-42PH9BSTH-42PH9EKTH-42PH9ESGPH9D Chassis
High Definition Plasma Display
SpecificationsPower Source 220-240 V AC, 50/60HzPower Consumption
Power on 330 W
Stand-by condition Save off 0.8 W, Save on 0.6 W
Power off condition 0.2 W
Plasma Display panel Drive method: AC type 42-inch,16:9 aspect ratio
Contrast Ratio Max 10000:1
Screen size920 mm (W) 518 mm (H) 1,056 mm (diagonal)
(No. of pixels) 786,432 (1,024 (W) 768 (H))
[3,072 768 dots]
Operating conditionTemperature 32 F - 104 F (0 C - 40 C)
Humidity 20 % - 80 %
Applicable signalsColor System NTSC, PAL, PAL60, SECAM, Modified NTSC
Scanning format 525 (480) / 60i 60p, 625 (575) / 50i 50p, 750 (720) / 60p 50p, 1125 (1080) / 60i 50i 24p 25p30p 24sF .... SMPTE274M, 1250 (1080) / 50i
PC signals VGA, SVGA, XGA,
SXGA, UXGA ..... (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminalsAV VIDEO IN (BNC) 1.0 Vp-p (75-ohm or high impedance)
S VIDEO IN (MINI DIN 4PIN) Y: 1 Vp-p (75-ohm), C: 0.286 Vp-p (75-ohm)
AUDIO IN (RCA PIN JACK 4) 0.5 Vrms
PC (HIGH-DENSITY Mini-D-SUB 15PIN) Y or G with / sync 1.0 Vp-p (75-ohm)
Y or G without / sync 0.7 Vp-p (75-ohm)
B / PB / CB:0.7 Vp-p (75-ohm)
ORDER NO. PCZ0608053CE
1 Applicable signals 4 2 Safety Precautions 5
2.1. General Guidelines 5
3 Prevention of Electro Static Discharge (ESD) toElectrostatically Sensitive (ES) Devices 6
4 About lead free solder (PbF) 7 5 Service Hint 8 6 Disassembly 9
6.1. Removal of the Back Cover 9
6.2. Removal of the HU-Board 9
6.3. Removal of the Slot Block 9
6.4. Removal of the J-Board 9
6.5. Removal of the HX-Board 10
6.6. Removal of the PB-Board 10
6.7. Removal of the DA-Board 10
6.8. Removal of the P-Board 11
6.9. Removal of the D-Board 11
6.10. Removal of the H3-Board (L, R) 11
6.11. Removal of the SU-Board and the SD-Board 12
6.12. Removal of the SC-Board 12
6.13. Removal of the SS-Board 12
6.14. Removal of the C1, C2-Board 13
6.15. Removal of the S1-Board 13
6.16. Removal of the Fan 14
6.17. Removal of the V1-Board, V2-Board and the Operation
Button 14
6.18. Removal of the Escutcheon and the Front Glass 15
6.19. Removal of the Plasma Panel 16
7 Location of Lead Wiring 18 7.1. Location of Lead Wiring (1) 18
7.2. Location of Lead wiring (2) 19
7.3. Location of Lead wiring (3) 20
7.4. Location of Lead Wiring (4) 20
8 Adjustment Procedure 21 8.1. Driver Set-up 21
8.2. Initialization Pulse Adjust 22
8.3. P.C.B. (Printed Circuit Board) exchange 22
8.4. Adjustment Volume Location 23
8.5. Test Point Location 23
9 Service mode 24 9.1. CAT (computer Aided Test) mode 24
9.2. IIC mode structure (following items value is sample data.)
27
10 Adjustment 28 10.1. RGB white balance adjustment 28
10.2. HD white balance adjustment 30
10.3. Power control adjustment 32
11 Troubleshooting guide 33 11.1. Self Check 33
11.2. No Power 35
11.3. No Picture 35
11.4. Local screen failure 36
R / PR / CR:0.7 Vp-p (75-ohm)
HD / VD:1.0 - 5.0 Vp-p (high impedance)
VBS (use HD port) with / picture 1.0 Vp-p (high impedance)
without / picture 0.3 Vp-p (high impedance)
AUDIO IN (M3 JACK) 0.5 Vrms
SERIAL EXTERNAL CONTROL TERMINAL (D-SUB 9PIN) RS-232C COMPATIBLE
SPEAKERS (6) 16 W [8 W + 8 W] (10 % THD)
Accessories SuppliedRemote Control Transmitter EUR7636090R
Batteries 2 R6 Size
Fixing bands TMME187 2
Dimensions (W H D) 1,020 mm 610 mm 89 mmMass (weight)
main unit only approx. 27.0kg net
with speakers approx. 31.0kg
Notes: Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
This equipment complies with the EMC standards listed below.EN55022, EN55024, EN61000-3-2, EN61000-3-3.
CONTENTS Page Page
2
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
12 Option Setting 37 13 Conductor Views 39
13.1. P-Board 39
13.2. PB-Board 42
13.3. HU-Board 43
13.4. HX-Board 44
13.5. H3, S1, V1 and V2-Board 45
13.6. J-Board 46
13.7. DA-Board 48
13.8. D-Board 50
13.9. C1-Board 52
13.10. C2-Board 53
13.11. SC-Board 54
13.12. SU-Board 57
13.13. SD-Board 58
13.14. SS-Board 59
14 Block and Schematic Diagram 61 14.1. Schematic Diagram Notes 61
14.2. Main Block Diagram 62
14.3. P-Board Block Diagram 63
14.4. P-Board (1 of 6) Schematic Diagram 64
14.5. P-Board (2 of 6) Schematic Diagram 65
14.6. P-Board (3 of 6) Schematic Diagram 66
14.7. P-Board (4 of 6) Schematic Diagram 67
14.8. P-Board (5 of 6) Schematic Diagram 68
14.9. P-Board (6 of 6) Schematic Diagram 69
14.10. PB-Board Block and Schematic Diagram 70
14.11. HU-Board Block Diagram 71
14.12. HU-Board (1 of 2) Schematic Diagram 72
14.13. HU-Board (2 of 2) Schematic Diagram 73
14.14. HX-Board Block and Schematic Diagram 74
14.15. V1 and V2-Board Block and Schematic Diagram 75
14.16. J-Board (1 of 2) Block Diagram 76
14.17. J-Board (2 of 2) Block Diagram 77
14.18. J-Board (1 of 5) and H3-Board Schematic Diagram 78
14.19. J-Board (2 of 5) Schematic Diagram 79
14.20. J-Board (3 of 5) Schematic Diagram 80
14.21. J-Board (4 of 5) Schematic Diagram 81
14.22. J-Board (5 of 5) Schematic Diagram 82
14.23. DA-Board (1 of 2) Block Diagram 83
14.24. DA-Board (2 of 2) Block Diagram 84
14.25. DA-Board (1 of 6) Schematic Diagram 85
14.26. DA-Board (2 of 6) Schematic Diagram 86
14.27. DA-Board (3 of 6) Schematic Diagram 87
14.28. DA-Board (4 of 6) Schematic Diagram 88
14.29. DA-Board (5 of 6) Schematic Diagram 89
14.30. DA-Board (6 of 6) Schematic Diagram 90
14.31. D-Board Block Diagram 91
14.32. D-Board (1 of 6) Schematic Diagram 92
14.33. D-Board (2 of 6) Schematic Diagram 93
14.34. D-Board (3 of 6) Schematic Diagram 94
14.35. D-Board (4 of 6) Schematic Diagram 95
14.36. D-Board (5 of 6) Schematic Diagram 96
14.37. D-Board (6 of 6) Schematic Diagram 97
14.38. C1 and C2-Board Block Diagram 98
14.39. C1-Board (1 of 2) Schematic Diagram 99
14.40. C1-Board (2 of 2) Schematic Diagram 100
14.41. C2-Board (1 of 2) Schematic Diagram 101
14.42. C2-Board (2 of 2) Schematic Diagram 102
14.43. SC, SU and SD-Board Block Diagram 103
14.44. SC-Board (1 of 2) Schematic Diagram 104
14.45. SC-Board (2 of 2) Schematic Diagram 105
14.46. SU-Board (1 of 2) Schematic Diagram 106
14.47. SU-Board (2 of 2) Schematic Diagram 107
14.48. SD-Board (1 of 2) Schematic Diagram 108
14.49. SD-Board (2 of 2) Schematic Diagram 109
14.50. SS and S1-Board Block Diagram 110
14.51. SS and S1-Board Schematic Diagram 111
15 Parts Location 113 15.1. Exploded View 113
15.2. Cable relation 115
15.3. Packing summary 116
16 Mechanical Replacement Parts List 118 17 Replacement Parts List 119
17.1. Relpacement Parts List Notes 119
17.2. Electrical Replacement Parts List 120
3
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
1 Applicable signals
4
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
2.1.1. Leakage Current Cold Check 1. Unplug the AC cord and connect a jumper between the two
prongs on the plug. 2. Measure the resistance value, with an ohmmeter, between
the jumpered AC plug and each exposed metallic cabinetpart on the equipment such as screw heads, connectors,control shafts, etc. When the exposed metallic part has areturn path to the chassis, the reading should be between1M and 5.2M.When the exposed metal does not have a return path to
the chassis, the reading must be .
Figure 1
2.1.2. Leakage Current Hot Check (SeeFigure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use anisolation transformer for this check.
2. Connect a 1.5k, 10 watts resistor, in parallel with a 0.15Fcapacitors, between each exposed metallic part on the setand a good earth ground such as a water pipe, as shown inFigure 1.
3. Use an AC voltmeter, with 1000 ohms/volt or moresensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure thevoltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of theabove measurements.
6. The potential at any point should not exceed 0.75 voltsRMS. A leakage current tester (Simpson Model 229 orequivalent) may be used to make the hot checks, leakagecurrent must not exceed 1/2 milliamp. In case ameasurement is outside of the limits specified, there is apossibility of a shock hazard, and the equipment should berepaired and rechecked before it is returned to thecustomer.
2 Safety Precautions2.1. General Guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed. 3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
5
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
3 Prevention of Electro Static Discharge (ESD) toElectrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors andsemiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damagecaused by electro static discharge (ESD). 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such asaluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can
generate electrical charge sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparableconductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective materialto the chassis or circuit assembly into which the device will be installed.Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such as the brushing
together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient todamage an ES device).
6
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
4 About lead free solder (PbF)Note: Lead is listed as (Pb) in the periodic table of elements.In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in its manufacture due to environmental conservation issues. For service and repair work, wedsuggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol stamped on the back of PCB.Caution
Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 F (30~40 C) higher.Please use a high temperature soldering iron and set it to 700 20 F (370 10 C).
Pb free solder will tend to splash when heated too high (about 1100 F or 600 C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pbsolder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
After applying PbF solder to double layered boards, please check the component side for excess solder which may flow ontothe opposite side. (see figure below)
Suggested Pb free solderThere are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder.However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
7
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
5 Service Hint
Board Name FunctionDA Digital Signal Processor, MiconD Format Converter, Plasma AI Processor, Sub-Field ProcessorJ Slot Interface (Audio / Video / Sync input Switch), SYNC processor, Sound processor
SS Sustain driveSC Scan driveSU Scan out (Upper)SD Scan out (Lower)C1 Data Drive (Right)C2 Data Drive (Left)H3 Speaker terminalS1 Power switchV1 Remote receiver, LED-G, RV2 Key switchP Power supply
PB Fan controlHX PC / RS-232C_Input terminalHU Dual Video terminal (BNC / S)
Note: Extension cable kit Slot Board is supplied as service fixtures and tools.
(Parts No. TZSC0704)
8
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
6 Disassembly To disassemble P.C.B., wait for 1 minute after power was
off for discharge from electrolysis capacitors. and marks indicate screw positions.
6.1. Removal of the Back Cover 1. Remove the screws (18 , 6 , 4 ) and then remove
the Back Cover.
6.2. Removal of the HU-Board 1. Remove the 4 screws(A) and then remove the HU Terminal
Block. 2. Remove the 4 screws(B). 3. Remove the 3 screws(C) and then remove the HU-Board.
6.3. Removal of the Slot Block 1. Disconnect the couplers (J1, J2, J3, J4, J5, J6, J7, J8, J10,
J15,J30). 2. Remove the 4 screws and then remove the Slot Block.
6.4. Removal of the J-Board 1. Remove the HU Terminal Block and the HA Terminal Block.
(Reference to Removal of the HU-Board and the HA-Board) 2. Remove the Slot Block.
(Reference to Removal of the Slot Block) 3. The Slot Block is turned inside out. 4. Remove the 6 screws and then remove the Slot cover.
5. Remove the 6 screws. 6. Release the coupler(J14) from HX-Board and then remove
the J-Board.
9
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
6.5. Removal of the HX-Board 1. Remove the HU Terminal Block.
(Reference to Removal of the HU-Board) 2. Remove the Slot Block.
(Reference to Removal of the Slot Block) 3. Remove the J-Board.
(Reference to Removal of the J-Board) 4. Remove the 2 screws and then remove the Slot Case.
5. Remove the 4 Hexagonal-Head screws and the 1 screwand then remove the HX-Board.
6.6. Removal of the PB-Board 1. Disconnect the couplers(PB30, PB31, PB33, PB35). 2. Remove the 1 screw and then remove the PB-Board.
6.7. Removal of the DA-Board 1. Disconnect the couplers(PB30, PB31, PB33, PB35). 2. Remove the 2 screws and then remove the PB-Board
Block.
3. Disconnect the couplers(DA1, DA3, DA5, DA6). 4. Remove the Flexible Cable from the coupler(DA2). 5. Remove the 2 screws and then remove the DA-Board and
Fixed Plate.
Note:A re-setup of the destination is performed by MS modeafter DA-Board exchange.
10
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
6.8. Removal of the P-Board 1. Disconnect the couplers(P2, P5, P9, P10, P11, P12, P23,
P25) 2. Remove the 6 screws and then remove the P-Board.
6.9. Removal of the D-Board 1. Remove the Slot Block.
(Reference to Removal of the Slot Block) 2. Disconnect the couplers(D5, D20, D25) 3. Remove the Flexible Cable from the couplers (D3, D31,
D32). 4. Remove the 4 screws and then remove the D-Board.
6.10. Removal of the H3-Board (L,R)
1. Remove the each 1 screw and then remove the SpeakerTerminal Block (L, R).
2. Disconnect the coupler(H37). 3. Remove the 3 screws (D) and then remove the H3-Board.
11
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
6.11. Removal of the SU-Board andthe SD-Board
1. Remove the Speaker Terminal Block(R).(Reference to Removal of the H3-Board(L, R))
2. Remove the Flexible Cable from the couplers(SU1, SU2,SU3, SU4, SD1, SD2, SD3, SD4) and then remove the SU-Board.
3. Remove the 3 screws.
4. Disconnect the couplers(SU45, SD46). 5. Slide the SU-Board and the SD-Board to the left, remove
the SU-Board and the SD-Board from the couplers(SC41,SC42).
6.12. Removal of the SC-Board 1. Remove the Speaker Terminal Block(R).
(Reference to Removal of the H3-Board(L, R)) 2. Disconnect the couplers(SU45, SD46). 3. Remove the 3 screws ( ) and then slide the SU-Board and
the SD-Board to the left.
4. Disconnect the couplers(SC2, SC20, SC23). 5. Remove the 6 screws and then remove the SC-Board.
6.13. Removal of the SS-Board 1. Disconnect the couplers(SS11, SS12, SS23, SS34). 2. Remove the Flexible Cable from the couplers(SS41, SS42,
SS43, SS44). 3. Remove the 6 screws and then remove the SS-Board.
12
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
6.14. Removal of the C1, C2-Board 1. Remove the Slot Block.
(Reference to Removal of the Slot Block) 2. Remove the Speaker Terminal Block(L, R).
(Reference to Removal of the H3-Board(L, R)) 3. Remove the each 3 screws and then remove the Stand
Block(L, R).
6.14.1. Removal of the C1-Board 1. Remove the Flexible Cable from the couplers(C11, C12). 2. Remove the 8 screws ( ) and then remove the Flexible
Cable from the couplers(CB1, CB2, CB3, CB4). 3. Remove the 4 screws ( ) and then remove the C1-Board.
6.14.2. Removal of the C2-Board 1. Remove the Flexible Cable from the couplers(C21, C22). 2. Remove the 8 screws ( ) and then remove the Flexible
Cable from the couplers(CB5, CB6, CB7, CB8). 3. Remove the 4 screws ( ) and then remove the C2-Board.
6.15. Removal of the S1-Board 1. Disconnect the coupler(SS34).
2. Remove the 2 screws(E) and then remove the S1-BoardBlock.
3. Disconnect the coupler(S34). 4. Remove the 1 screw(F) and then remove the S1-Board.
13
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
6.16. Removal of the Fan 1. Disconnect the Fan Relay Couplers. 2. Remove the each 3 screws and then remove the 3 Fan
Blocks.
3. Remove the each 4 screws (G) and then remove the Fans.
4. Reassemble the Fans in reverse order. 5. Stick the Cushion (Fan) around the Fan.
Note:The Cushion (Fan) are unsuitable to reuse.Please use a new one at the time of Fan exchange.
6.17. Removal of the V1-Board, V2-Board and the OperationButton
1. Remove the S1-Board Block.(Reference to Removal of the S1-Board)
2. Disconnect the couplers(J2, J15). 3. Remove the 2 screws of the Escutcheon.
4. Pull the bottom of the Plasma Panel forward (arrow1). 5. Slide the Plasma Panel and then remove the Plasma Panel
(arrow2).
6. Remove the 5 screws and then remove the Fixed Angle(C).
14
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
7. Remove the 1 screw(L). 8. Disconnect the coupler(V2) and then remove the V1-Board. 9. Remove the operation button from the V2-Board. 10. Disconnect the coupler(V15) and then remove the V2-
Board.
6.18. Removal of the Escutcheonand the Front Glass
1. Remove the S1-Board Block.(Reference to Removal of the S1-Board)
2. Disconnect the couplers(J2, J15). 3. Remove the 2 screws of the Escutcheon.
4. Pull the bottom of the Plasma Panel forward (arrow1). 5. Slide the Plasma Panel and then remove the Plasma Panel
(arrow2).
6. Remove the 18 screws and then remove the Fixed Angle(A, B, C, D).
7. Remove the Front Glass
Note: when Front Glass is exchanged Each Front Glass Sponge must be stuck along the
edge of Fixed Angle.
Note The sponges are parts which cannot be recycled.
Please use the new article when you exchange theFront Glass.
8. Remove the 1 screw (L) and then remove the V1-Board. 9. Remove the V2-Board and Operation Button.
15
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
6.19. Removal of the Plasma Panel The C1,C2 module is connected with the plasma panel
for the repair. 1. Disconnect the Fan Relay Couplers. 2. Remove the each 3 screws ( ) and then remove the 3 Fan
Blocks. 3. Remove the each 3 screws ( ) and then remove the Stand
Block(L, R).
4. Disconnect the couplers(J1, J2, J3, J4, J5, J6, J7, J8, J10,J15, J30).
5. Remove the 4 screws and then remove the Slot Block.
6. Disconnect the coupler(DA5). 7. Remove the Flexible Cable from the coupler(DA2). 8. Remove the 4 screws and then remove the DA-Board
Block.
9. Disconnect the couplers(P2, P9, P11, P12, P23, P25). 10. Remove the 6 screws ( ) and then remove the P-Board. 11. Remove the each 1 screw ( ) and then remove the
Speaker Terminal Block(L, R).
12. Disconnect the coupler(D20). 13. Remove the Flexible Cable from the couplers(C11,C21). 14. Remove the 4 screws and then remove the D-Board.
15. Remove the SU-Board and the SD-Board.(Reference to Removal of the SU-Board and the SD-Board)
16. Remove the 1 screw ( ) and then remove the clamper. 17. Remove the 6 screws ( ) and then remove the SC-Board.
16
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
18. Disconnect the couplers(SS23, SS34). 19. Remove the Flexible Cable from the couplers(SS41, SS42,
SS43, SS44) 20. Remove the 6 screws and then remove the SS-Board.
21. Remove the Flexible Cable from the couplers(C12,C22).
22. Remove the 2 screws ( ) and then remove the S1-BoardBlock.
23. Remove the 3 screws ( ) and then remove the AC-InletBlock.
24. Remove the 2 screws of the Escutcheon.
25. Remove the 18 Spacers and Spacer Rings from the PlasmaPanel.
Caution Please confirm the installation place of Spacer and
Spacer Ring when you exchange the Plasma Panel,and install Spacer and Spacer Ring in an originalinstallation place after exchanging the PlasmaPanel.
26. Lift up the bottom of the Plasma Panel in the direction of thearrow 1 and pull the Plasma Panel in the direction of thearrow 2 and then remove the Plasma Panel.
17
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
7 Location of Lead Wiring7.1. Location of Lead Wiring (1)The lead wiring is dressed as shown in figure.
18
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
7.2. Location of Lead wiring (2)The lead wiring is dressed as shown in figure.
19
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
7.3. Location of Lead wiring (3)The lead wiring is dressed as shown in figure.
7.4. Location of Lead Wiring (4)The lead wiring is dressed as shown in figure.
20
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
8.1. Driver Set-up8.1.1. Item / Preparation 1. Input a white signal to plasma video input.
Aging pattern: 0 2. Set the picture controls as follows.
Picture menu: StandardPicture: +25Aspect: Full
Caution 1. First perform Vsus adjustment. 2. Confirmation of Vscn voltage should be performed after
confirmation of Vad adjustment.When Vad=-105V, Voltage of Vscn is 35V 4V.
8.1.2. AdjustmentsAdjust driver section voltages referring the panel data on thepanel data label.Check or adjust the following voltages with the multimeter.
Name Test Point Voltage Volume RemarksVsus TPVSUS
(SS)Vsus 2V R628 (P) *
Ve TPVE (SS) Ve 1V VR6000 (SS) *Vset TPVSET
(SC)260V 7V Fixed
Vad TPVAD (SC) -105V 1V VR6600 (SC)Vscn TPVSCN
(SC)Vad+140V 4V
Fixed
Vda TPVDA (SS) 75V 1V FixedVdat P12-1, 5 (P) 75.5V 0.1V R665 (P)PFC C446 (+)(-) 396V 0.5V R443 (P)
*See the Panel label.
8 Adjustment Procedure
21
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
8.2. Initialization Pulse Adjust 1. Input the White signal to plasma video input. 2. Set the picture controls as follows.
Picture menu: StandardPicture: +25Aspect: Full
3. Connect Oscilloscope to TPSC1 (T2) and adjust VR6602 for 19510 Sec.
Test point Volume LevelT2 TPSC1 (SC) VR6602 (SC) 195 10 Sec.
8.3. P.C.B. (Printed Circuit Board) exchange8.3.1. Caution 1. To remove P.C.B., wait 1 minute after power was off for discharge from electrolysis capacitors.
8.3.2. Quick adjustment after P.C.B. exchangeAdjust the following voltages with the multimeter.
P.C.B. Name Test Point Voltage Volume RemarksP Board Vsus TPVSUS (SS) Vsus 2V R628 (P) *
Vdat P12-1, 5 (P) 75.5V 0.1V R665 (P)PFC C446 (+) (-) (P) 396V 0.5V R443 (P)
SC Board Vad TPVAD (SC) -105V 1V VR6600 (SC)SS Board Ve TPVE (SS) Ve 1V VR6000 (SS) *D, J, DA Board White balance, Pedestal and Sub brightness for NTSC, PAL, HD, PC and 625i signalsDA Board Set Market Select Number to correct destination by MS mode. (See chap. 9.1.4)
*See the Panel label.Caution:
Absolutely do not reduce Vsus below Ve not to damage the P.C.B.
22
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
8.4. Adjustment Volume Location
8.5. Test Point Location
23
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
9 Service mode9.1. CAT (computer Aided Test) mode
To exit the CAT mode, access the ID mode and switch off the main power.
9.1.1. IIC modeSelect the IIC mode by Up/Down button on the remote control at the front page of CAT mode and then press the Action buttonon the remote control.
Subject and item are mentioned on IIC mode structure.
To exit the IIC mode, press the R button on the remote control.
24
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
9.1.2. CD modeSelect the CD mode by Up/Down button on the remote control at the front page of CAT mode and then press the Mute buttonon the remote control more than 5 seconds.
Micom software version (IC9702), this version can be upgrade by 1. replace of new version IC 2. Loading the new version software from loader tool, TZSC07036.Memory data change
To exit the CD mode, press the R button on the remote control.
9.1.3. SD modeSelect the SD mode by Up/Down button on the remote control at the front page of CAT mode and then press the Action buttonon the remote control.
To exit the SD mode, press the R button on the remote control.
25
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
9.1.4. MS modeSelect the MS mode by Up/Down button on the remote control at the front page of CAT mode and then press the Mute buttonon the remote control more than 5 seconds.
To exit the MS mode, press the R button on the remote control.
Caution:Market Select should be set after exchange of DA-Board.
Destination numberNumber Destination Number Destination
0 Japan 14 Thailand (Hotel)1 North America 15 --2 Europe 16 Mexico3 Others 17 Mexico (Hotel)4 Britain 18 China5 Taiwan 19 China (Hotel)6 Thailand 20 --7 -- 21 --8 Japan (Hotel) 22 --9 North America (Hotel) 23 --
10 Europe (Hotel) 24 --11 Others (Hotel) 25 --12 Britain (Hotel) 26 --
Default settingNumber Destination
1 North America
9.1.5. ID modeSelect the ID mode by Up/Down button on the remote control at the front page of CAT mode and then press the Mute button onthe remote control more than 5 seconds.
To exit the ID mode, press the R button on the remote control.
26
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
9.2. IIC mode structure (following items value is sample data.)
27
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
10 Adjustment10.1. RGB white balance adjustment
Instrument Name Connection Remarks RGB VGA W/B pattern
Color analyzer
(Minolta CA-100 or equivalent)
PC inputPanel surface
User setting: Normal(Picture menu: Standard)
Procedure Remarks Ensure aging is adequate.
Make sure the front panel to be used on the final set is fitted.
Make sure a color signal is not being shown before adjustment.
Put the color analyzer where there is little color variation.
1. Set COMPONET/RGB-IN SELECT to RGB.
2. Select the IIC mode PANEL W/B Adj. item.
3. Check that the color temperature is COOL (High).
4. Output a white balance pattern.
5. Touch the signal receiver of color analyzer to the highlight windows center.
6. Fix G drive at E0h and adjust B drive and R drive so x, y become the Color temperatureHigh in the below table.
7. Increase R/G/B together so the maximum drive value in R/G/B becomes FCh.
8. Set color temperature to NORMAL (Medium).
9. Fix G drive at E0h and adjust B drive and R drive so the highlight windows x, y becomesthe Color temperature Medium in the below table.
10. Increase R/G/B together so the maximum drive value in R/G/B becomes FCh.
11. Set color temperature to WARM(Low).
12. Set G drive to E0h and adjust B drive and R drive so the highlight windows x, y becomethe Color temperature Low shown in the below table.
13. Increase R/G/B together so the maximum drive value in R/G/B becomes FCh.
14. Copy the R drive, G drive and B drive data in NTSC, PAL DVI region.
Adjustment target
Hi-light: x 0.003 y 0.003
Hi-light is target of the number at drive adjustment in the hi-light windows.
Therefore, it is not target of the hi-light number at after adjustment white balance.
Picture Menu: StandardPicture: 25Aspect: FullPosition and size: Normal
Highlight section Signal amplitude 75%
Cutoff standard G: 80h
Drive standard G: E0h
28
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
29
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
10.2. HD white balance adjustmentInstrument Name Connection Remarks
HD W/B pattern (COMPONENT Output)
Color analyzer
(Minolta CA-100 or equivalent)
PC inputPanel surface
User setting: Normal(Picture menu: Standard)
Procedure Remarks Ensure aging is adequate.
Make sure the front panel to be used on the final set is fitted.
Make sure a color signal is not being shown before adjustment.
Put the color analyzer where there is little color variation.
1. Set COMPONENT/RGB-IN SELECT to COMPONENT
2. Select the IIC mode "PANEL W/B Adj. item.
3. Check that the color temperature is COOL (High).
4. Output a white balance pattern.
5. Touch the signal receiver of color analyzer to the highlight windows center.
6. Fix G drive at E0h and adjust B drive and R drive so x, y become the "Color temperatureHigh" in the below table.
7. Increase R/G/B together so the maximum drive value in R/G/B becomes FCh.
8. Set color temperature to NORMAL (Medium).
9. Fix G drive at E0h and adjust B drive and R drive so the highlight windows x, y becomesthe "Color temperature Medium" in the below table.
10. Increase R/G/B together so the maximum drive value in R/G/B becomes FCh.
11. Set color temperature to "WARM (Low)".
12. Set G drive to E0h and adjust B drive and R drive so the highlight windows x, y becomethe Color temperature Low shown in the below table.
13. Increase R/G/B together so the maximum drive value in R/G/B becomes FCh.
14. Copy the R drive, G drive and B drive data in YUV1_525ip, YUV3_625ip region.
Adjustment target
Hi-light: x 0.003 y 0.003
Hi-light is target of the number at drive adjustment in the hi-light windows.
Therefore, it is not target of the hi-light number at after adjustment white balance.
Picture Menu: StandardPicture: 25Aspect: FullPosition and size: Normal
Highlight section Signal amplitude 75%
Cutoff standard G: 80h
Drive standard G: E0h
30
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
31
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
10.3. Power control adjustmentInstrument Name Connection Remarks
PC (RGB) signal generator
(Leader: VGA/No.9 signal)
Wattmeter
PC input
Connect the AC power of theadjustment set to the wattmeter.
Set RGB at COMPONENT/RGB-INSELECT in Setup Menu.
Procedure Remarks[condition] Make sure the set is aged for 30 minutes or more before adjustment.
Voltage 120V 50/60Hz (variation within 1%)
Volume at minimum and screen size at full
PC input and picture menu at normalized Dynamic
1. Connect the sets AC power to the wattmeter.
2. Receive the VGA No.9 signal from Leader.
3. Select the PWRCTL item in Panel APL/ABL in the IIC mode.
4. Adjust PWRCTL so the sets power consumption is description below.
Adjust to shift large to small for DAC.
Factory adjustment with OSD
42" 210+5/-12W
BUSCON without OSD
42" 287+5/-12W
No.9 SignalTop half: Full color barBottom half: Horizontal 10 steps bar
Notes: 1. When passing through factory
adjustment mode, the power fewwatts which goes down is theconsideration being completed.
2. Adjust the large number for DACwhen they have 2 adjustmentpoints.
32
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
11.1.1. Display Indication 1. Self-check is used to automatically check the bus line
controlled circuit of the Plasma display. 2. To get into the Self-check mode, press the volume down
button on the customer controls at the bottom of the set, atthe same time pressing the OFF-TIMER button on theremote control, and the screen will show:-
If the CCU ports have been checked and found to be incorrectOr not located then " - - " will appear in place of " OK " 01 in the line of the PTCT means the number of blinks ofthe Power LED is 1. (Reference to 11.1.2) H09 in the line of the PTCT is the error code.Note:
The line of the PTCT displays when you get into the Self-check mode for the first time only after the Power LEDblinks.
11 Troubleshooting guide11.1. Self Check
11.1.2. Power LED Blinking timing chart 1. Subject
Information of LED Blinking timing chart. 2. Contents
When an abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, thedefective block can be identified by the number of blinks of the Power LED on the front panel of the unit.
33
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
3. RemarksAbove Fan function is operated during the fans are installed.
34
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
11.2. No PowerFirst check point
There are following 3 states of No Power indication by power LED. 1. No lit. 2. Green is lit then turns red blinking a few seconds later. 3. Only red is lit.
11.3. No Picture
35
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
11.4. Local screen failurePlasma display may have local area failure on the screen. Fig - 1 is the possible defect P.C.B. for each local area.
Fig - 1
36
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
12 Option Setting
37
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
Option Menu for GPH9D series
GPH9D chassis series have special function and operation setting facility called Option Menu. This Option Menu is useful forspecial function required customers. This should be set at the installation stage.
Option menus default setting ContentsOff-timer function Enable Off-timer operation Enable/Disable.Onscreen display On Enable/Disable to display input mode indication after power on and no signal
indication.Initial INPUT Off Sets the initial input mode when the power is turned on. Allow input mode
selection while power is on.Initial VOL level Off Sets the initial volume level when the power is turned on. Allow Volume
control while power is on.Maximum VOL Level Off Sets the maximum volume to desired level. Volume cannot exceed this level.INPUT lock Off Fixes the input mode to AV, Component/RGB or PC. Can not change input
mode by input selection key.Studio W/B Off Set warm mode color temperature to 3,200 Kelvin.Advanced PIP Off Off: Sets normal two screen display mode.
On: Sets Advanced PIP mode.Display size Off Adjusts the image display size on screen.
On: Sets the image display size approximately 95% of the normal imagedisplay.
Button lock Off Enable/Disable bottom operation buttons (Input, Menu, Enter and/or volumeup/down)
Remocon User Level Off Remote key invalidation.Off: Valid key is all key of remote.User1: Valid key are only Stand-by (ON/OFF), Input, Direct input, Status,Surround, Sound mute On/Off, and volume adjustment.User2: Valid key is only Stand-by (ON/OFF).User3: All keys are null and void
ID select 0 Set ID number from 0 to 100.Remote ID Off Remote ID function On/Off.
(While the Remote ID on, standard remote function can not control the unit.)Serial ID Off Serial ID function On/OffSlot power Off Sets the slot power mode while the power is turned on.
Allow Optional Terminal Board insert Slots while power is on.V. Installation Off V. Installation function On/Off (Not used)Rotate Off The image rotates 180 degrees (up-down)Serial Slot Select Slot1 Selects the slot which communicates serial.
Note: The setting of an external command can be set only from the fixedserial terminal.
Note:When both main unit buttons and remote control are disabled due to the Button lock, Remocon User level or RemoteIDadjustments, set all the values Off so that all the buttons are enabled again.Press the Volume down button on main unit together with R button on the remote control and hold for more than 5 seconds.The SHIPPING menu is displayed and the lock is released when it disappears.
38
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
13 Conductor Views13.1. P-Board
A B C D E F G H I
1
2
3
4
5
6
P-BOARD (FOIL SIDE)TNPA3911AJ
TH-42PH9BK/BS/EK/ESP-BOARD TNPA3911AJ
TH-42PH9BK/BS/EK/ESP-BOARD TNPA3911AJ
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
39
TH-42PH9BK/BS/EK/ESP-BOARD PARTS LOCATION
TH-42PH9BK/BS/EK/ESP-BOARD PARTS LOCATION
Parts LocationParts Location
P-BOARD (COMPONENT SIDE)
IC402 G-4IC406 D-1IC409 F-3IC411 H-4IC504 H-4IC509 B-5IC512 C-5
IC
Q404 C-2Q406 D-2Q412 B-3Q413 B-2Q434 H-3Q505 C-5Q507 C-5Q527 C-5
TRANSITOR
R443 D-1R628 C-5R661 D-5R665 C-5R671 B-5
VOLUME
P-BOARD (FOIL SIDE)
IC401 B-4IC402 C-4IC403 B-4IC404 C-4IC405 C-4IC406 F-1IC408 B-4IC409 C-3IC410 B-4IC411 B-4IC412 A-4IC501 B-5IC502 B-5IC504 B-4IC505 H-5IC506 G-5IC507 G-6IC509 H-5IC510 C-6IC512 F-5IC520 F-6
IC
Q401 B-4Q402 E-1Q404 F-1Q406 F-2Q407 F-1Q408 H-3Q409 H-2Q412 H-3Q413 H-2Q415 B-4Q418 G-1Q420 F-1Q421 G-1Q422 F-1Q434 B-4Q501 A-5Q502 A-5Q505 G-6Q507 G-5Q508 E-5Q509 E-5Q510 F-5Q512 A-4Q517 E-4Q520 E-4Q521 C-5Q524 D-5Q525 G-5Q527 F-5Q530 G-5
TRANSISTOR
R443 F-1R628 G-5R661 E-5R665 G-5R671 H-4
Q535 A-5Q537 C-5Q538 E-5Q540 G-5Q541 F-5Q551 C-5Q553 B-5Q554 B-5Q555 E-4Q556 D-4Q557 B-5Q558 A-4Q559 B-5Q561 A-5Q563 A-6Q564 F-6Q565 F-5Q566 E-6Q567 F-5Q568 B-4Q569 B-6
VOLUME
P
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
40
A B C D E F G H I
1
2
3
4
5
6
P-BOARD (COMPONENT SIDE)TNPA3911AJ
TH-42PH9BK/BS/EK/ESP-BOARD TNPA3911AJ
TH-42PH9BK/BS/EK/ESP-BOARD TNPA3911AJ
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
41
13.2. PB-Board
A B C D E F G H I
1
2
3
4
5
6
PB-BOARD (FOIL SIDE)TNPA3655AD
PB-BOARD (COMPONENT SIDE)TNPA3655AD
TH-42PH9BK/BS/EK/ESPB-BOARD TNPA3655AD
TH-42PH9BK/BS/EK/ESPB-BOARD TNPA3655AD
Q850
L851L
852
R850
R851
R852
R853
R854
R855
R856
R857
R858
R859
R860
R861
R862
R863
R864
C850
C851
C852
C853
C854
TP
FA
N D850
D851
D852
D853
D854
D855
D856
D857
D858
D859 D8
60
IC850
JS851
JS852
PB
30
PB
31
PB
32
PB
33
PB
34
PB
35
PB
36
PB
37
PB
38
TNPA3655 1 PB PbF
E BC
SEE REVERSE FOR ORDER NO.
15
2
4
315
13
13
13
1
3
13
13
13
13
Q8
50
L8
51
L8
52
R850
R8
51
R852
R853
R854
R855
R856
R857
R858
R859
R8
60
R861
R862
R863
R8
64
C850
C8
51
C852
C8
53
C8
54
J1
J2
D850
D851
D852
D853
D854
D855
D8
56
D857
D858
D8
59
D8
60
IC8
50
JS851
JS8
52
PB
30
PB
31
PB
32
PB
33
PB
34
PB
35
PB
36
PB
37
PB
38
J101
1PBTNPA3655NO.ORDER
1
3
4
52
15
31
31
31
3131
1 3
1 3
13
PBParts Location
PB-BOARD (FOIL SIDE)
IC
IC850 C-2 Q850 B-3
TPFAN B-2
TRANSISTOR
TP
Parts Location
PB-BOARD (COMPONENT SIDE)
IC
IC850 G-3 Q850 G-3
TRANSISTOR
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
42
13.3. HU-Board
A B C D E F G H I
1
2
3
4
5
6
C4
46
C4
48
L30
8
L309
L3
19
L320
JK3
01
JK3
02
JK3
03
JK30
4
Q301
C3
06
Q302
C3
07
Q3
03
Q3
04
C3
08Q305
Q30
6
C3
10
C3
12
C314
H1
C3
17
C3
18
C319C320
C321
C3
22
C323
C3
24
C325
C3
26
C327
C32
8
C329
D3
07
D3
08
D30
9
C330
C331
C332
D3
10
IC3
05
C335
C3
36
IC307
R3
10
R3
12
R3
14
R3
15
R3
16
R3
18
C3
40
R319
C341
C3
42
C3
45
R3
20
C348
R3
21
C349
R3
22
R3
23
R3
24
R3
25
R326
R32
7
R328R329
C3
54C356
R3
30
C358
R3
31
C359
R332
R33
3
R334
R33
5
R336
R337
R338
C360R339
C361C362C364
C36
5C
36
7
C3
69
R345
R3
46C370
C371C373
C374
C3
75
R351
C379
R3
52
R3
53
R3
54
C3
80
C3
81
R359
C382
C3
84
C3
85
C3
86
C3
87
C3
88
R360
R3
61
R362
R3
63
C390
C3
91
C3
92
C3
93
C394
C3
95
R3
70
C3
98
R377
R383
R391R392
R394
R3
95
R3
96
C400
C4
01
C402
C403
C404C405C406C407C408
C410
C411
C412
C413
C414
C415
C420
C423
R4
02
R4
05
R4
06
R4
09
C4
32
C4
33
C4
34
C4
35
C4
36
C4
37
C4
38
R4
10
HU
1
CR
NO
.3
TN
PA
38
85
PbF
LR
LR
CY
ORD
ERNO
.
B2
A1
A2
A4
0A
39
B3
9B
40
B1
125
26 50
1
2829
56
C440
C4
41
C4
42
C4
43
C4
44
C445
L3
01
L3
02
C447
L3
03
L3
04
C4
49
L305
L306
L3
07
C450
C4
51
L3
10
L311
L312
L313
L3
14
L3
15
L316
L317
L3
18
TP301
TP302
TP
30
3
TP
30
4
TP305
JK3
01
JK3
02
JK3
03
JK304
C301
C3
02
C3
03
C304
C305
C3
09
Q307
Q308
C3
11
C313
H0
H1
C315
C316
D3
01
D3
02
D3
03
D3
04
D305
R3
01
D306
R3
02
R3
03
R3
04
R3
05
R3
06
R307
R308
IC301
R3
09 IC
30
2
IC303
C3
33
IC304
C334
D311
IC306
C337
IC3
08
C338
C339
IC3
09
R3
11
R3
13
R3
17
C3
43
C3
44
C3
46
C347
C350
C351C352C353
C3
55
C357C363
C366
C368
R340
R3
41
R342
R3
43
R344
R3
47
R348
R349
C3
72
C3
76
C3
77
C3
78
R350
R3
55
R3
56
R3
57
R358 C3
83
C3
89
R3
64
R3
65
R3
66
R367 R368 R369
C3
96
C3
97
C3
99
R371
R3
72
R3
73
R3
74
R3
75
R3
76
R3
78
R3
79
R3
80
R3
81
R3
82
R3
84
R3
85
R3
86
R3
89
R3
90
R397
R399
X301
C409
C416
C417
C418
C419
C4
21
C422
C4
24
C4
25
C4
26
C4
27
R4
00
C4
28
R4
01
C4
29
R4
03
R4
04
R407
R4
08
C4
30
C4
31
R4
11
C4
39
R4
12
R4
13
R4
14
R4
17
TNPA38851HUCR NO.3L
R
GND
HD VDR4
15
R4
16
PbF
LR
LR
CY
SEEREVERSEFORORDERNO.
18
A1A2B1B2
A39A40B39B40
1
12
13 24
25
36
3748
1
3
4
5
1
3 4
5
1
44
45 88
89
132
133176
14
5 8
1 8
916
14
5 8
+
TH-42PH9BK/BS/EK/ESHU-BOARD TXNHU1ZFTE
TH-42PH9BK/BS/EK/ESHU-BOARD TXNHU1ZFTE
HU-BOARD (FOIL SIDE)TXNHU1ZFTE
HU-BOARD (COMPONENT SIDE)TXNHU1ZFTE
Parts Location
HU-BOARD
IC
IC3301 F-2IC3302 G-2IC3303 G-4IC3304 G-3IC3305 B-3IC3306 H-2IC3307 B-2IC3308 G-2IC3309 G-2
Q3301 D-2Q3302 D-2Q3303 D-3Q3304 D-3Q3305 C-2Q3306 C-3Q3307 G-3Q3308 G-3
TRANSISTOR
TP3301 I-3TP3302 I-3TP3303 H-2TP3304 H-2TP3305 H-4
TRANSISTORTP
HU
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
43
13.4. HX-Board
A B C D E F G H I
1
2
3
4
5
6
JK509
JK511
JK513
CR NO.3
TNPA2842
HX
1
PbF
1 5
6 9
1 5
6 10
11 15
SEE REVERSE FOR ORDER NO.
L507
L508
L509
L510
L511
L512
L513
L514
L515
L516
L517
L526
R653
R65
4
R655
R65
6R663
R66
4
R668
L555
R67
2JK
509
JK51
1JK
513
C523
C524
D50
1
D502
D50
3
D504
D505
D506
D507D508
D509
R508
R50
9
IC502
D510
Q53
1
Q53
2
Q53
3
R51
0
Q53
4
R51
1
Q53
5
Q53
6
Q537
R526R527R528
C550
R52
9
C551
R53
0
R537
R538
C56
1
C562
C563
C56
4
C565
C56
6
C56
7
R54
7 R548
R776 R777
R778
R58
5
R586
R589
R78
0
R78
1
R78
2R
783
R59
0
R78
4
R591
R78
5
R592
R786
R593
R78
7
R788
R789
R79
0
HX1
R79
1
R792
R794
C404
C405
C409R400
TNPA2842CR NO.3
A
B
B
C
C
1
D
D
E
E
A
HXPbF
15
69
15
ORDER NO.
1
4 5
8
111
12
22
HX-BOARD(FOIL SIDE)TZTNP03ZQTU
HX-BOARD(COMPONENT SIDE)TZTNP03ZQTU
TH-42PH9BK/BS/EK/ESHX-BOARD TZTNP03ZQTU
TH-42PH9BK/BS/EK/ESHX-BOARD TZTNP03ZQTU
Parts Location
HX-BOARD
IC
IC3502 E-4 Q3531 D-4Q3532 D-4Q3533 E-4Q3534 E-4Q3535 E-4Q3536 E-4Q3537 F-4
TRANSISTOR
HX
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
44
13.5. H3, S1, V1 and V2-Board
A B C D E F G H I
1
2
3
4
5
6
R1500
C1
53
0D
15
51
D1552
D1553
D1
55
4
R1550R1551
R1552
R1
55
3
R1
55
4R1555
SN1550
L1
50
1
L1
50
2
L1
50
3
L1504
L1
50
5L
15
06
RM001TNPA3640 1V1
R1556 SEE ORDER NO.FORREVERSE
PbF
SW061
S34
S1
1P
bF13
RE
VE
RS
EF
OR
NO
.O
RD
ER
SE
ETN
PA
3642
SW061
S34
ORDER NO.
TNPA3642
S1 1
13
Q1540
D1550
SN
15
50
V2
RM
00
1
TN
PA
3640
V1
1O
RDER
NO.
16 PbF
L1
50
7
L1
50
8
V15
TNPA
3641
V2
1
PbF
ORD
ERNO
.3 1
R1
51
3
SW1550 SW1551 SW1552SW1553SW1554
STR VOL.UP VOL.DOWN F TV/VTR
R1
51
1
R1
51
0
R1
51
2
SEE ORDER NO.FORREVERSE PbF
TNPA3641 1 V2
JK8500
H37
1 H3TNPA3931SEE REVERSE
ORDER NO.FOR
31
JK8500
H37
TNPA3931 1 H3 PbF
ORDER NO.
1 3
TH-42PH9BK/BS/EK/ESV2-BOARD TNPA3641 V1-BOARD TNPA3640S1-BOARD TNPA3642 H3-BOARD TNPA3931
TH-42PH9BK/BS/EK/ESV2-BOARD TNPA3641 V1-BOARD TNPA3640S1-BOARD TNPA3642 H3-BOARD TNPA3931
V2-BOARD(FOIL SIDE)TNPA3641
V2-BOARD(COMPONENT SIDE)TNPA3641
V1-BOARD(FOIL SIDE)TNPA3640
V1-BOARD(COMPONENT SIDE)TNPA3640
S1-BOARD(FOIL SIDE)TNPA3642
S1-BOARD(COMPONENT SIDE)TNPA3642
H3-BOARD (FOIL SIDE)TNPA3931
H3-BOARD (COMPONENT SIDE)TNPA3931
S1
V1V2H3
H3
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
45
13.6. J-Board
A B C D E F G H I
1
2
3
4
5
6
C2364
C2365
C2368
C2369
R2355
R2356
R2357
R2358
R2359
R2360J8
J13
J14
C8185
L2330L2331
3
TNPA3896 1
1
J
2
J7J11J12
IC8003C8072
C8073
C8074
C8075
R3230
R3231
R802
R803
R804
R805
R806
R807
R3050
R8069
R810
R811
R3059
R812
R813
R814
R815
R3061
R825 R826
R3070
R3071
R3072
R8088
R3078
R3079
R836
R3080
C803
C804
C805
C806
C808
C809
R3090
R3091
R3092
C810
C813C814
C815
C818
C819
C820
R2301
R2302
C8108
C8109
C8112
C3101
C855
C856
C3103
D802
C3110
C864
C2366C2367
C3114
C2378
R8112
R8113
R8117
R3104
R8118
R3105
IC801
R3106
IC802
R3110
R3111
R2367
R2368
C2392
C2393
R3118
JS8096
R3135
R3136
R3137
R2392
R2393R2394
R2395
R2396
R3144
C8183
R3163
D8181
D8183
D8184
R8181
D8185 R3172R
8189
R8190
R3188
R3189
C2409
R3190
R3197R3198
C2414
C2415
C2416
C2419
R2401
R2402
R2403
R2408
R2409
C8005C
8007
C8009
R2420
R2421
C8016
R2422
R2423
C3201
C3202
C3203
C8025
D8001
D8003
C3015
D8205
R8202
D8206
R8203
D8207
R8204
D8208
D3001
D3003
C3028
D3004
C3029
R3004
C3030
C3035
R8021
R8023
R8025
R8026
R8033
D3024
R3025
R3026R3027
PbF
SEE REVERSE FOR ORDER NO.
1 458
1
3
A1
A2
B1B2
A40
A39
B39B40
111
12 22
13
A1
A2
B1
B2
A40
A39
B39B40
A1
A2
B1
B2
A40A39
B39B40
1 10
1120
1 458
TH-42PH9BK/BS/EK/ESJ-BOARD TNPA3896
TH-42PH9BK/BS/EK/ESJ-BOARD TNPA3896
J-BOARD (FOIL SIDE)TNPA3896
Parts Location
J-BOARD (FOIL SIDE)
IC801 E-2IC802 E-2IC8003 I-1
IC
J
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
46
A B C D E F G H I
1
2
3
4
5
6
J2
J3
J8
J13
J14
J30
J34
1 JTNPA3896
THERMAL PAD
TH
ER
MA
L P
AD
J1 J4J5
J6
J7 J10
J11
J12
J15
A
A
C3058
R3
03
0
C3
05
9
R8045
R3
03
1
R3032R3033
R8047
R3034
R8048
C8
07
0
R3035
C8071
R3036R3037
C3060
R3038
R3039
R8050
R8
05
1R
80
54
R3040
R8055
R3041
R8056
R3042
R3043
R8
05
7
R3044
C8
08
0 C8081
R3045
R3046
C8
08
2
R3047
C8
08
3
R3
04
8
C8084
R3049
R8
06
0
R8065
R3
05
1
X8181
R8
06
7
R3
05
3
R3054
FL8000
R3057R3058
D3
06
1
R8072
R818
R3
06
0
R8
19
R3062
R8077
R3
06
3
R3
06
4
R3
06
5
R3
06
6
R3
06
7
FL
30
00
R820
R3
06
8
L3140
R3
06
9
FL
30
01
R821
R8
22
FL3002
R823
FL3003
FL
30
04
R8081
FL3006
R8
27
FL3007
FL3008
R8
28
R829
R3
07
3
R3
07
4
R3
07
5
R8
08
9
R3
07
6
R3
07
7
R8
30
FL3010
TP
JV1
R831
R832
R8
33
R834R835
R8
09
3
R837
R8
38
R3
08
1
R8
39
R3082
R3
08
3
R8
09
7R
80
98
R3084
R3
08
5
C801
R3
08
6
C802
R3087
R8
40
R3
08
8
Q2
30
0
R841
R3089
C8
07
R3
09
3
R3094
R3
09
5
C8
11
R3096
C8
12
L8182
L8183
L8184L8185
C8
16
L8186
C817L8187
L8188
L8189
C8
21
C822
C823
C8
24
C8
25
D2
30
1
D2
30
2
C827
D2303
C8
28
C8
29
R2303
R2
30
4
C830
C831
IC2
30
1
C832
IC2
30
2
C8
33
IC2303
C8
34
IC2305
C8
35
Q2
33
1
C837
C8
38
C839
C8100
C840
C8
10
1
C841
C8102
C8
43
C8103
C8
44
C8
45
C8105
C8
46
C8
10
6
C8
10
7
C847
C848
C2350
C8
11
1
C2
35
1
C2
35
2
C8113
C2
35
3
C8114
C2354
C8
11
5
C2
35
5
C8116
C2356
C857
C2357
C858
C2
35
8
C3105
C859
C2
35
9
C3106
C3107
C3
10
8
C8120
C2360
C860
ZA
30
01
C8121
D801
C2361
C861
ZA
30
02
C8122
C862
C2362
D803
ZA
30
03
C863
C8
12
3
C2
36
3
ZA3004
C2364
D804
D805
C3111
ZA
30
05
C865
C2365
C3112D806
C8
66
ZA
30
06
C3
11
3
C8
67
D807
ZA3007
D808
R8
10
0
C2368
C8
68 ZA3008
D809
C3
11
5
C2369
C869
D8
10
IC8100
C2370
C2371
C2
37
2
C2373C2374
C2375
C2376
Q2372
C2
37
7
C2379
R2351
R2352
R2
35
3
R2
35
4
R3
10
1
R2355
R3
10
2
R2356
R3
10
3
R2
35
7
C2
38
0
R2
35
8
R8
11
9
C2
38
1
R2359
C2382
IC803R3107
C2383
IC804
C2384
R3108
IC3101
L8
00
1
IC8
05
C2385
C2386
L8003
C2387
R8
12
0
C3
13
4
C2388R2360
C3
13
5
R8
12
1
L8005
R2
36
1
C2389
C3
13
6
R8
12
2
R2
36
2
R8123
R2
36
3
R8124
R2
36
4
R8125
R2
36
5
R8126
R2
36
6
R8127
R8128
R3
11
4
C2390
R8129
C2391
R3116
R3
11
7
C2
39
4
R3119
C2395 C2396
C3
14
3
C2397
C3
14
4
C2
39
8
C3145
C2
39
9
C3
14
6
L3002R3120JS8094
L3005
R3
12
1
L3006
R3125
R3
12
6
C3150
C3151
C3152
R2
38
3R2384
R2
38
5
R2
38
6
R2387
R3134
R2
38
8
R2389R2390
R2
39
1
R3
14
0R3141
R3143
R2397
R2
39
8
R2
39
9
C8181
C8182
C8185
Q8181
Q8182
Q8183
C8187
Q8184
R3150
R3151
IC3150
IC3151
IC3
15
2
R3
16
0R
31
61
D8180
R8180
L3050
R8182
R8183
R3170
R8184
R8185R8186
R8
18
7R
81
88
IC8181
C2400
C2401
X2
30
1
C2
40
2C
24
03C2404
C2
40
5C
24
06
C2
40
7C
24
08
TPJH1
ZA2300
R3
19
1
ZA2301
R3
19
2
C2410
R3195
C2411
R3196
C2412 C2413
C2
41
7C
24
18
C2
42
0
C2421
C2
42
5
C2426
R2
40
0
R2404R2405
R2
40
6
R2407
C8001
C8003
R2410
R2411
Q8002
R2412
R2
41
3R
24
14
R2415
R2
41
6R
24
17
C8
20
0
R2
41
8
C8201
R2
41
9
Q8
20
0Q
82
01
Q8202
Q8
20
3
C8013
Q8
01
0
Q8
20
4
C8
01
5
Q8011
C3
00
1
Q8
01
2
Q8
01
3
R2424
C3
00
4
Q3001
C8
01
9
R2425
R2
42
6
R2427
Q3004
Q8
01
9
C3009
C3200
C8021
C8023 C3010
C3011
C3012
C8
02
7
C3
01
3C
30
14
C8
02
9
R8001
R8002
C3
01
6
C3
01
7
R8003
C3018
R8
00
4
R8005
C3019
R8
00
6
D8200
C8030
R8009
IC8001
D8
20
1
IC8
00
3D
82
03
C8033
C3020
D8
01
0
R8200
D8
20
4
D8
01
1
IC8
00
5
C8035
C3021
R8201
C8036
C3
02
2
C3
02
3
IC8007
R8010
C3
02
4
C8038
D8
20
9
R8011
R8
20
5
C3
02
5
IC8009
L8
01
C3
02
6
R8012
R8206
L802
R8
20
7
C3
02
7
L803
R8208
L804
R3
00
1
D3
00
5
R8209
L805
R3
00
2
D3007
R3
00
3
R8017
L8
07
D3008
R8018
L8
08
L2330
L809
L2331
R3
00
7
IC8014
R3008
C3
03
1
C8045
IC3
00
1
IC3
00
2
C3032
IC8016
C3033
IC3003
C3034
L810
IC3004
C8049
IC3005
L811
IC3
00
6
L8
12
IC3
00
7
R8024
IC3008
R8029
C8051
L8
10
1
L8102L8103
C3
04
0
L8104
C3
04
1
L8105
C3
04
2
L8106
L8107
C3
04
3
R3
21
0
L8108
R8031
R3
21
1R3
21
2
R3
21
3
R3
21
4
R8035
R3
21
5
R8036
R3
21
6
R3
21
7
R8037
R3023R3024
R3
21
8
R8039
R3
21
9
R3028
C3
05
1
R3029
C3
05
2
C3053
C3054
C3055
R8
04
1
C3056
C3057
PbF
B
C
E
ORDER NO.
1
20
40
41
60
61
80
21
B
C
E
14
5 8
NP
NP
17
NP NP
16
1 29
302
1
3
A1
A2
B1
B2
A39
A40
B39
B40
1 11
1222
13
15
18
1
4 5
8
1
10
11
20
1
45
8
1
5
1
45
8
1
1415
28
7
8
21
22
1 19
202
111
1 211 21
1 3 16
A39
A40
B39
B40
A1A2
B1B2
A1A2
A39
A40B39
B40
B1B2
18
9 162011
101
1
78
14
1
4
5
8
1
4 5
8 1
10
11
201
7 8
14
1
8 9
16
1
8 9
16
114
15
2425
38
39
48
1
8 9
16
1
45
8
1
89
16
1
14
15
28
7 82
2 21
1 14
15
28
7 8
22 21
TH-42PH9BK/BS/EK/ESJ-BOARD TNPA3896
TH-42PH9BK/BS/EK/ESJ-BOARD TNPA3896
J-BOARD (COMPONENT SIDE)TNPA3896
Parts Location
J-BOARD (COMPONENT SIDE)
IC
IC803 E-2IC804 D-2IC805 F-2IC2301 H-2IC2302 H-2IC2303 G-2IC2305 H-1IC3001 F-1IC3002 C-2IC3003 C-1IC3004 C-2IC3005 B-2IC3006 C-2IC3007 C-2IC3008 G-2IC3101 A-2IC3150 C-3IC3151 C-3IC3152 G-2IC8001 B-1IC8003 B-1IC8005 A-1IC8007 B-1IC8009 B-1IC8014 D-1IC8016 D-1IC8100 D-2IC8181 G-3
Q2300 H-2Q2331 H-2Q2372 G-2Q3001 C-3Q3004 A-3Q8002 B-2Q8010 D-1Q8011 D-1Q8012 D-1Q8013 D-1Q8019 B-2Q8181 G-3Q8182 G-2Q8183 C-2Q8184 C-2Q8200 B-3Q8201 B-3Q8202 B-3Q8203 A-3Q8204 A-3
TRANSISTOR
TPJH1 A-2TPJV1 A-2
TRANSISTORTP
J
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
47
13.7. DA-Board
A B C D E F G H I
1
2
3
4
5
6
R994R995
C0
06
C2
02
C2
03
C0
10
C204C205
C0
12
C206
C0
13
C207
C0
14
C2
08
C015
C2
09
C0
18
C210
C2
11
C021
C215
C2
16
C217
C2
18
C0
25
C2
19
C0
26
C0
27
R0
01
C6
05
R0
02
R0
03
C6
07
C2
20
C6
09
C2
21
C222
R007
C0
31
R009
C0
32
C2
26
C2
27
IC003
C8
03
C6
10
Q8
01
C6
11
C6
13
R011
R0
17
R0
18
C0
41
R019
C0
42
C043
R0
21
R022
R023
R0
24
R0
25
R0
26
R027
R0
28
R0
29
D8
01
R2
23
R800
R2
25
IC6
05
R801
R802
R2
27
R804
R0
35
R2
29
L301
R0
36
L302
R037
L3
03
R808
R039
IC0
31
R809
IC0
32
R6
18
R6
19
R0
41
L501
R0
42
R812
L5
02
R0
43
R813
L5
03
R0
44
L5
04
R6
20
R0
45
R815
R6
21
L5
05
R6
22
R6
27
L7
02
L704
R8
20
R822
R825R
25
6
TP
70
1
C6
73
R845
TP
90
1
R846
TP
90
2
TP710
TP713
R2
71
R2
72
R2
73
R2
77
R2
78
R854
R2
79
R855
R8
59
TP721 TP722
C8
87
R285
R8
61 C696
R6
71
R6
72 R
67
3R
67
4
TP731
R6
75
TP732
R6
76
TP
73
3
R6
77
IC671
R2
92
R2
93
R2
94
R871
R2
95
R2
96
R2
97
R8
80
R691
R887R888
R8
90
R8
91
R894
R895
C3
02
C3
03
C309
C501C502
C3
11
C3
12
C3
13
C507
C508
C7
01
C7
03
C7
09
C9
01
C903
C904
C711
C9
05
C712
C9
06
C713
C9
08
C909
Q712
C911 C912
R3
13
C918
R314
C919
R315
D701
D7
02
R316
D7
03
D7
04
R319
R7
02
R7
04
C9
20
D709
R511
L2
02
L203
C9
23
R5
13
R708
C9
24
R5
14
R320
L2
05
C925
R5
15
L206
C7
32
D9
02
C926
R516
C927
D903
C7
33
C928
C9
29
D905
D714
R710R711
C5
45
R136
C546
C5
47
R138
C5
48
R1
39
R909
IC9
01
C9
31
C5
49
R7
16
C9
32
C933
C7
40
R718
C9
34
C7
41
R719
C9
35 R5
25
C9
36
R5
26
C743
C9
37
R9
10
C938
C5
50
D7
21
R911
C9
39
C551
R142
R912
D722
C5
52
D723
R913
C5
53
R144
R914
D724
R7
20
C5
54
R915
D725
C749
C5
55
R916
D726
R1
46
C5
56
R722
D727
R917
C5
57
R723
R918
D728
R1
48
C5
58
D729
R919
R7
25
C5
59
C942
C9
43
C750
R7
28
C9
44
C945
C753
R920D730
C7
54
C9
48
C5
60
R921
C949
C561
D732
C562C563
D734
R9
24
C5
64
C5
65
R9
26
C5
66
R7
33
C567
R7
34
C9
50
C5
68
C5
69
R7
36
C570
Q9
55
C571
Q956
R9
32
C572
R933
C5
73
R934
C5
74
R935
C5
75
R936
C5
76
R937
C5
77
R938
C5
78
R745
R939
C5
79
Q9
61
Q962
R940
C5
80
R941
C5
81
R9
42
C5
82
R9
43
C5
83
R944
C5
84
R945
FL
30
1
C5
85
C5
86
C587
R7
54
C588C589
R7
56
R7
58
R9
50
R5
68
C590
R9
51
FL501
C5
91
R5
69 R
95
2
C5
92
FL
50
2
FL
50
3
C593
R9
53
R7
60
C594
R9
54
R761
C595
R9
55
R9
56
C596
R763
R957C597
R7
64
R958
C9
81
R7
65
R9
59
IC951
C9
82
R7
66
IC952
C983
R7
67
C984
IC9
54
R7
69
IC955
FL
70
3
IC957
R9
60
R9
62
R9
63
R9
64
R7
71
R9
65
R9
66
R773
R9
67
R9
68
R7
75
R969
R777
R5
87
R970
R5
88
R971
R5
89
R972
R9
73
R9
74
R783R784
R590
R591
R5
92
R788
R5
95
R9
83
R9
84
R7
90
R9
85
R791
R792R793
R795
R798R799
R991
R992R993
1
34
5
DA1TNPA3901
3
CR NO.4
21
PbF
134
51 3
45
1 3
45
SEE REVERSE FOR ORDER NO.
1
4
5
8
13
45
112
1324
1
12
1324
1
3
45
11
2
13
24
13
45
TH-42PH9BK/BS/EK/ESDA-BOARD TZTNP020ZKT
TH-42PH9BK/BS/EK/ESDA-BOARD TZTNP020ZKT
DA-BOARD (FOIL SIDE)TZTNP020ZKT
Parts Location
DA-BOARD (FOIL SIDE)
IC
IC4003 D-2IC4031 E-2IC4032 E-2IC4605 E-3IC4671 C-3IC4901 E-4IC4951 E-4IC4952 A-4IC4954 E-2IC4955 A-5IC4957 B-5
Q4712 B-4Q4801 C-1Q4955 B-2Q4956 B-2Q4961 E-4Q4962 E-4
TRANSISTOR
TP4701 B-1TP4710 B-1TP4713 B-1TP4721 C-1TP4722 C-1TP4731 D-1TP4732 C-1TP4733 C-1TP4901 A-3TP4902 C-2
TRANSISTORTP
DA
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
48
A B C D E F G H I
1
2
3
4
5
6
DA4
DA10
DA1
1
DA5
DA6
DA7
C0
01
C0
02
C0
03
C0
04
C0
05
C007
C008
C0
09
C201
C0
11
C0
16
C0
17
C0
19
C212C213
C020
C214
C022
C0
23
C0
24
C600
X501 C6
01
C6
02 C6
03
C028
C6
04
DA
41
DA
42
C606
R0
04
C6
08
R0
05
R0
06
R008
C225
IC001
X7
01
C801
IC002
C802
C8
04
C2
28
R2
01
C2
29
Q802
C612
Q803
R010
R204
C614
R205
R012
R206
R013
R207
R014
R208
C2
30
C231
R015
R209
IC201
R016
IC202
IC2
03
C235
C236
R211R212
R213
R020
R214R215R216R217
R218
C2
41
R219
C6
29
R220
R2
21
R2
22
R2
24
R2
26
R803
R2
28
R805R806
R038
IC8
01
IC8
02
IC8
03
R2
30
R231R232
R2
33
R040
R2
34
R810
R2
35
R811
R2
36
R2
37
R2
38
R814
R2
39
R046
R816
R8
17
R818R819
R626
R2
40
L7
01
R2
41
R2
42
R2
43
L7
03
R244R245
R821
R2
46
R823
R824
R249
R631
R826
R827
R828
L9
01
R829
L902
L903
R2
50
R2
51
R2
52
R8
30
R8
31
R8
32
R2
57
R8
33
R8
34
R640
R8
35
R8
36
R8
37
R8
38
FL001
R8
39
C8
61
C8
62
C863
C864
R260
R2
61
C865
C671
C866
C672
R2
63
R2
64
R8
40
R8
41
R2
65
R8
42
R8
43
R844
R847R848
C8
71
R849
C872
C8
73
R657
R6
58
R850
R2
74
R851
R2
75
R852
R2
76
R853
R856
R8
57
R8
58
C8
81
C8
82
C884
R280
C8
85
R281
C886
R2
82
R283R284
R8
60
R8
62
R8
63 R
86
4
R8
65
R8
66
R8
67
R8
68
R8
69
R8
70
R8
72
R873
R8
74
R875
R8
76
R8
77
R8
78
R8
79
R8
81
R8
83
R8
84
R8
86
R8
92
R8
93
C107
C1
08
ZA
00
1
C301
ZA002
C304
C305
C3
06
C3
07
C3
08
C503
C310
C504
C5
05
C5
06
FL
67
1C702
C7
04
C705
Q7
01
Q7
02
C706
Q7
03
C7
07
C708
Q7
04
R105
Q7
05
Q7
06
R106
Q7
07
R107
Q708
Q7
09
IC102
C9
02
IC1
03
C710
Q901
Q902
C9
07
Q903
C7
14
Q7
10
PA901
C715
C7
16
R113
C717
Q713
Q714
C718
C7
19
IC301
C910
R5
01
R5
02
C9
13
R503
C9
14
R504
C915
R505
C9
16
R506
R3
12
C9
17
R507
IC5
00
R508
IC501
R509
IC5
02
R3
17
R3
18
R701
R7
03
R510
L2
01
C9
21
R7
06
C9
22
R512
R7
07
IC7
01
D901
R3
21
R7
09
IC7
02
R3
22
R3
23
IC7
03
R517
R9
00
IC704
R3
24
D9
04
R5
18
D7
11
R325
C5
41
R5
19
R9
02
D7
12
C7
36
R326
D9
06
C542
R133
R9
03
C7
37
D7
13
R327
C543
R134
C7
38
R9
04
C5
44
R135
C7
39
R9
06
R712
R907
R137
R713
R908
C9
30
R5
20
R7
14
R5
21
R7
15
R5
22
R7
17
R5
23 R5
24
IC7
11
C7
42
IC713
R5
27
C7
44
IC7
14
R5
28
IC7
15
R5
29
R7
21
R1
47
R7
24
C940
R5
30
R1
49
C941R
53
1
R7
26
R5
32
R7
27
R5
33
R534
R7
29
C751
R535
C7
52
C946
R536
R537
C9
47
R5
38
C755
R539
C7
56
R9
22
R923
D733
R7
30
R925
D7
35
R731R732
R9
27
R9
28
R540
R7
35
R9
29
R541R542
R7
37
R543
R7
38
R544
R7
39
R545R546R547
R9
30
R548
R9
31
R549
R7
40
R7
41
R742
R743
R550R551
R746
R552
R7
47
R553
R748
R554
R749
R555R556
R557R558
R1
71
R5
59
R750R751R752
R9
46
R7
53
R9
47
R9
48
R5
60
R7
55
R949
R561
R562
R7
57
R563
R564
R7
59
R565
R566R567
FL504
R762
C598
R570
C599
R571R572
IC9
53
R573
R7
68
R574
R5
75
IC956
R5
76
R577
R578
FL705
R579
R961
FL
70
6 FL
70
7F
L7
08
R7
70
FL709
R7
72
C9
90
R7
74
R580
C9
91
R581
C9
92
R7
76
R5
82
C993
R5
83
C9
94
R7
78
R584
C9
95
R7
79
R5
85
C9
96
R5
86
C9
97
C9
98
C9
99
R7
80 R7
81
R975
R786
R5
96
R9
81
L6
71
R9
86
R9
87
R796
R7
97
DA1
DA2
DA3DA
MM
3
DAMM4
DAMM5
TNPA3901
DA
MM
1
CR NO.4
DA
DA
MM
2
1
PbF
11
4
1
12
121
12
11
31
1
3
11
21
12
1
2021
40
41
60
61 80
15
A
1
134
5
110
1120
13
4
5
1 3
4
5
1
4
5
8
16
71
2
ORDER NO.
1
11 20
10
1
3
45
116
17
32
4849
64
33
1
10
11
20
AB C D EF G H J K
LM
NP R T
UV W YAA
ABAC
2
1
43
567
8910
11
1213
14
1516
17
1819
2021
22
23
1
30
31
50
51
80
10
0
81
+
144
45
8889
132
133
176
1 24
4825
14 5
8
1
3 4
5
1 3
45
1
4 5
8
110
11 20
13
4 5
+
+
1 3
45
13
45
12
19
20
140
1
29
302
TH-42PH9BK/BS/EK/ESDA-BOARD TZTNP020ZKT
TH-42PH9BK/BS/EK/ESDA-BOARD TZTNP020ZKT
DA-BOARD (COMPONENT SIDE)TZTNP020ZKT
Parts Location
DA-BOARD (COMPONENT SIDE)
IC
IC4001 B-1IC4002 A-2IC4102 B-2IC4103 B-2IC4201 B-3IC4202 A-3IC4203 B-2IC4301 B-5IC4500 D-4IC4501 C-5IC4502 E-5IC4701 D-3IC4702 C-3IC4703 D-4IC4704 D-2IC4711 E-1IC4713 D-2IC4714 C-2IC4715 D-1IC4801 D-1IC4802 D-2IC4803 D-1IC4953 E-2IC4956 E-2
Q4701 D-3Q4702 E-4Q4703 E-4Q4704 E-4Q4705 E-4Q4706 E-1Q4707 E-1Q4708 D-2Q4709 C-2Q4710 C-2Q4713 E-2Q4714 E-2Q4802 E-4Q4803 E-4Q4901 E-5Q4902 B-4Q4903 E-5
TRANSISTOR
DA
TH-42PH9BK / TH-42PH9BS / TH-42PH9EK / TH-42PH9ES /
49
13.8. D-Board
A B C D E F G H I
1
2
3
4
5
6
Q010
C028
C029
C800
C801
C032
C802
IC002
C803
C033
C804
C034
C805
C035
C036
C807
C037
C038
Q805
C809
C039
Q806
D017
D018
D019
IC011
D020
C817
Q044
Q045
Q046
Q047
Q048
Q049
R028
C822
C054
C824
D801
C056
C827
R223
R800
R801
Q055
R225
R226
D806
R802
Q056
R803
Q057
R227
D807
R804
Q058
D808
D809
R805
R229
R806
R807C
830
IC800
R808
IC801
C831
R809
C832
D810
Q060
R230R231
R232
IC806
D813
IC807
R810
C839
D815
IC809
L501
R811
L502
R813
R237
R814
R238
R815
R239
R816
C840
R819
R240
C846
C847
C848
R821
R824
C467
C850
C468
R828
C469
C853C855
C857
C858
R830
C859
R834
R835
C860
R841
R842R843
D9
R846R847
R848
R849
R850
R854
R859
C882
C883
C884
C885
C886
C887
R861
R862
R863
R094R095R096 R097
R868
R098
C891
R869
C896
FL806
C897
C898
R870
C899
R871
R872
R873
R876
R877
R878
R879
R880
R883
R884
R887
R891
R892
R893
R896
R897
C100
Q300
Q301
Q302
Q500
R100
R101
C512
C513
C515
C516
C517
D300
C518
C900
D301
C519
C901
C902C903
C904
C905
C906
C907
C520
R110
C908
C521
C909
C522
C523
C524 C525
C526
C527
C528
R500
C910
C529
R501
C911
C912
R503
C913
R504
C914
R505
C915
R506
C916
R507
C917
C530
R508
C918
R509
R121
C919
IC502
C532
R317
C536
C537
R127
C538
R128
C920
C539
R129
R511
C921
C922
R513
C923
C924
C925
C926
R516
C927
R900
C540
C928
R131
R901
C929
R132
R902
R133
R903
R134
R904
R135
R136
R906
R137
R907
R520
R138R908
C930
R521
R139
C931
C932
R523
C933
R524
C934
R525
C
top related